I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

I have never reviewed anything and feel compelled to chime in. The Maytag Bravos XL is the WORST washer dryer set ever. My 20 year old tiny washer with agitator cleaned a million times better in half the time. In fact this washer doesnt even clean your clothes! The reason is because so little water comes in and you cannot manually control the amount of water. Ive tried deep water wash-total joke. Heavy duty wash and extra rinse, still no better. You can wash it 2-3 times with the same poor results. Who wants to put on dirty underwear! The dryer easily takes 2 cycles to get an average size load dry and forget sheets and towels! They take 2 hours.

On 8/26/16, we purchased a top-of-the-line Maytag dishwasher from Lowes of Palm Bay, Fl. It began leaking water out one side shortly after installation. Because of a hospitalization, we were not able to report the problem to Lowes until the first part of December. A repairman from Brandts in Sebastian, Fl. came out on 12/6/16 and said it might be the door gasket, but he did not have a new one with him and if it continued, to call back. I called again and another repairman from Brandts came out on 1/3/17. He said it was out of square and he took out 2 screws and said to cut back on detergent because too many suds could cause it to leak (which we find ludicrous). Now it leaks on both sides. This is not a small leak; it soaks the bath towel we put under the door. On 1/11/17 Brandts sent 2 repairmen out and they claimed we needed to cut way back on detergent and put in a capful of salad oil because our water softener is causing the suds which causes the leak. We now use 1/2 teaspoon of detergent and the capful of salad oil. It is still leaking. Our previous Kitchen Aid dishwasher never leaked and we used the recommended amount of detergent in it. We are apparently stuck with a brand-new dishwasher that cannot be fixed. We will NEVER buy another Maytag appliance.

July 2018 I bought a new Maytag electric washer and dryer. After one mo. the enamel inside the dryer started come off in sheets. It was replaced with 2019 model which after 3 mos. wont come on unless you unplug it and plug it back in after using it. I am now waiting for Maytag to send a repairman to come look at it. Steer clear of Maytag front load electric dryers.

Maytag Centennial Washer MVWC400XW2 - Bought this washer Fall 2011 -- first 6 months had to be serviced and now (February 2016) needs to be serviced again - has not cleaned my clothes for the last 3 months. Now, I have had to order a new washer - you can bet it wasnt a Maytag. My new washer will not be delivered for another 3 weeks. Past the part of not cleaning clothes, now it wont even empty the water, or pump out the water. It makes a horrible noise! Before it wouldnt use any water, now, it fills completely up. I do not know if it will make it through this current load much less another 3 weeks. Always bought Maytag before BUT WILL NOT AGAIN - after what I have been through with this washer!

I purchased a Maytag Bravo xl washer & dryer for $1600 in May 2017. Sunday, the user interface panel went out in the washer. After an $85 diagnostic visit, we were told it would be $500 to repair and take an additional 5 days. My husband is recovering from major knee surgery so I was short on choices. I elected to purchase a new speed queen and will never purchase Maytag again. The 10 yr warranty tag on the front is useless!

I just purchased a washer in April and the door is locked with my son brand new clothes is stuck in the machine in water, I called to get service and was told a date 2 weeks away, worst experience ever. Sorry ma’am is what I was told in a non caring way. I’m so furious if I could return this washer and dryer I would.

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

I purchased a new Maytag dishwasher model MDB7609AWB1 approximately 2yrs ago from Sears. We purchased quite a few new appliances from them and they are always helpful. Within the first year, right after the warranty was up, it stopped working. No lights on the power panel. I called Sears, out of warranty, sorry. Said they would give me a deal on the repair. Sears came out, replaced the computer. $230.00. 6 months later, it stops working again. I go on line to look up these models and sure enough a lot of people are having the same issues. I did some of the checks that they said to do and found my plastic door latch was broken. A little plastic arm that actuates the switches broke. Should have been made of metal. I replace it myself, very easy, by the way. So I figure, in another 8 months it will prob break again. They run anywhere from $19.00-$30.00. 2 days ago power panel and light, not working again. I called Sears and asked them if they were having issues with the power panels that this was the second time in less than 2 years, and if there were any recalls, they said no. I guess they dont follow their reviews, but according to google reviews, its a major problem with most of them. Maytag, Whirlpool, and Amanda. Ordered a new panel today, again they are $141 from Sears but if you shop, you can get a new one for less than $85.00. If you have any kind of mechanical skills, you can replace it in less than 20 mins. It just seems to me that this big companies have let their quality control go and are more concerned about the profit. There should be a recall on these. Do Not buy a Maytag/Whirlpool dishwasher, they are total junk. Sorry Maytag, you lost another customer.

We moved into a new house and the GE washer died after the first week, then the Whirlpool replacement died after two weeks. Decided to try the Maytag which the store gave us for $50 more than the Whirlpool. It runs like a champ. At least two loads of laundry a day every day and sometimes weekends. Clothes come out perfect, no damage and the machine is quiet.

After owning Maytag Model MHWE450WW01 for nine months, we had to have the bearing and drum replaced. It was down two weeks, and I missed two half days of work. Two weeks after being supposedly fixed, it is down again, belt out this time and I will be missing two half days of work again.After missing two days of work, I still have a piece of junk washing machine.

I purchased a Maytag dishwasher less than 2 years ago through Home Depot and did not purchase the extended warranty. The start button has stopped working and is not lighting up. I was referred by Pacific Sales, the appliance sales company at Home Depot, directly to Maytag to schedule repairs which I am willing to pay for. After a nearly hour long call between hold times and conversations I was told the service would be scheduled for Thursday or Friday of this week. As we were scheduling the appointment, I was told the computer for scheduling had gone down and to call the next day to schedule. I called next day and spoke with a customer service rep who said there was no record of my call the day before. I gave her all of my information, then she transferred me to another service person who then had no record of my two prior conversations. After giving my info to the this 3rd customer service representative, I learned that a repair could not be scheduled for over a week. I asked to speak with someone about my complaints and was told there was no one I could speak with but that she would pass on the complaint. I asked for a return call or email to confirm that my complaint was received and she said that I would not get that. I then asked for a free service call because of their poor customer service. This was of course denied. The dishwasher has been fine for the short period of time I have owned it but I wont buy another Maytag because of their poor customer service and because the dishwasher has a problem in less than two years. I am just writing this as a warning for other potential Maytag customers.

I own an iron in case a guest needs to use it but I seriously havent ironed in over 20 years. I moved into a home in November and the appliances stayed with the home. I am systematically destroying my clothes that I always washed and dried but NEVER IRONED. They come out of the Maytag washer already wrinkled. I try to unwrinkle them in the dryer. I took 2 items to the dry cleaners to see if they could steam them but no results yet. What gives Maytag???

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

I have enjoyed my microwave and it has lasted 10 years so far. The only problem I have had is the handle coming off but I clip it back on. Also I changed the bulb. The microwave is over the stove and matched the rest of my appliances. Basically, I would recommend Maytag for any appliances that a person would need to buy.

I bought my Maytag in 2013. It worked fine at first but for the last year it isnt getting clothes clean. In fact, some look like theyve never been washed. I have to run the rinse cycle 2-3 times and they still seem somewhat soapy. The washer still leaves clothes drippy after running the spin cycle. It takes 2-3 hours to complete a small load. I wish I had my old Kenmore back. It worked fine for nearly 20 years!

I can see by the comments on this page that the letter I sent to Whirlpool was in vain. I purchased a Maytag double oven gas range (MGT8775XW00) from our local Lowes. We were remodeling a home we had purchased. Unfortunately (as anyone whos been involved in home remodeling/renovation knows well), it took much longer than I thought it would before range could be installed. It was several months later before it was installed. First time I tried to use the top oven, it would heat to set temp (I assume) and then shut down. The larger bottom oven had erratic heating. I tried adjusting oven temps but it was a guessing game. We had Fix-Rite Corp out twice and they were puzzled by the problem. Two times, they replaced the control panel. After the second repair, it was decided the only thing to fix the kitchen was a complete gutting, new cabinets and floor. The oven was pulled out before I had a chance to use it again. By the time we got the kitchen finished and range reinstalled, I discovered the oven still had the same problems and the broiler would ignite sometimes and when it did, the flame would go out after 30 to 60 seconds and would not come back on. By this time, we were past the one-year warranty. After the first repair did not work, I tried to get Lowes to take it back and assured them I would purchase another range from them. They said they could not do that. Now I can see Im going to end up buying another range. Be assured it wont be Maytag and it wont be Lowes. I also own and use Maytag washer and dryer.

I purchased a Maytag Bravos XL Commercial Technology top loading washer, model # MVWB850YWO, in May 2012 and it was delivered in August 2012 due to a home purchase not being consummated. Anyway, I bought this washer and the matching dryer at Lowes and purchased a 4 year extended warranty with Lowes. This would cover me with a warranty through August 2017. I had some problems with the washer while under warranty and had it repaired at least twice. I have had, and still do, have a water leakage in the washer. The water when dispensing into the detergent compartment splashes over and you would think it would just go into the tub. Someway the water leaks down the inside of the washer and runs out onto the floor also causing rust to the inside of the front panel. The resolution was to turn the water pressure down on the supply lines. When this was done, the washer would quit running due to not enough water being dispersed into the drum. A replacement seal was installed and I still have the same problem. The repairmans final resolution was to put tape over half of the detergent dispenser to hold the water in the detergent dispenser and still allow me to put detergent in the dispenser. So, a towel is in front of the washer to soak up any leakage. Now, just 5 months after the extended warranty expired, the bearings under the wash tub are starting to roar during the spin cycle. I contacted Lowes service again and basically I am out of luck. The repair cost is expensive, the part and requires 2-3 hours of labor. I decided to chuck this washer and buy a new one. My wife found one that has an agitator, unfortunately another Maytag, and wants it as she has said the Bravos washer never seemed to get the clothes clean (due to not having an agitator). When checking online for references on a new washer and any recalls on my current washer, I discovered other Bravos XL owners having the same problem with the bearings in the tub. I contacted a local business to try and sell it to him for cheap and when I told him what was wrong with my washer his reply was, I have one just like it out back with the same problem. Dont need two problems. Cant even get rid of a Maytag washer due to it being junk. Many other reviews have listed problems with Maytag products especially since Whirlpool bought them. The Maytags of today are not your parents Maytag. Used to be the Maytag repairman sat around his office waiting for repair calls. This has changed considerably since Maytag sold out to Whirlpool. After doing some research, it seems Whirlpool has bought just about every company selling washers and dryers and are making them as a disposable item. I would advise not purchasing any product that is under the Whirlpool corporate umbrella as I feel whatever they buy, even a superior product like Maytag, they cheapen the product and try to benefit from the name, as in the case with Maytag. So, no more Maytag or Whirlpool products for me until they have proven they can build a quality product once again. Hello GE!!!!

Purchased a pair washer/dryer Maytag Bravo XL module from Home Depot, Brentwood, CA #1076 branch. The first day I received my machines, the dryer had a defect. I called them within 24 hours to report the issue and requesting a return. Home Depot wont take it back; they said I have to go though the factory warranty to fix any problems. Its like buying a car, once you drive it off the lot its yours they said. 3 weeks after the washer started making noise. Home Depot kept delaying my claim for more than six month so I couldnt dispute the charges with the credit card company and avoid the California lemon law. I consider this a loss of money and time. Worst appliance purchase experience ever.

I have a Maytag Bravos washer that has gotten to where every time you try to run the final spin, you get an unbalanced load code and it shuts off - it does this even when you try running it empty. This washer is 3 years old, and has been doing this progressively worse for the last 4 months until now. We cannot even get it run the final spin cycle now.

I bought a new Maytag washer two and half years ago. One of the new HE (High efficiency) models. Clothes do not get washed clean. But not only that, now its not washing at all. My previous machine was a Maytag...Had it for 22+ yrs. I guess Maytag quality is no longer what it used to be. Disappointed customer!

I purchased a refrigerator 9 years ago and the ice maker stopped working. When the repairman took it out there was plastic peeling from the ice mold. It cost $261.11 to have the ice maker replaced and the ice maker he replaced it with has the plastic on the ice mold. He said that GEs ice makers do not have the plastic coating but Maytags still do. I called Maytag and spoke to a supervisor and they said that there was nothing that they could do. I am filing this complaint because I feel that consumer need to be aware that they are ingesting plastic that is in their ice. I feel that Maytag should compensate me for the faulty part and also eliminate the plastic coating from their ice maker. This issue is impacting many other consumers and they need to issue a recall on the ice maker and replace it for free for other consumers.

I bought a Maytag Bravo washer with the new stainless tub and the bottom agitator. It also has a clear glass lid. Mistake. I can see the action of the washer thru the glass lid and it definitely doesnt wash the clothes very well. They just stay in the same position and the bottom clothes get agitation but the tops ones just sit there. The towels especially smell musty after they have been washed. Probably because they dont get agitation. The water level is so low that the clothes barely get wet. It was a good idea of the company to save water and electricity. But they must not have thought about getting the clothes clean. If I could I would get rid of this machine but I wouldnt want to subject anyone else to this type of washing machine. I would feel badly selling it knowing that it doesnt get the clothes clean. So I would never suggest getting a Maytag washer with a glass lid because you dont want to see what it is not doing.

I have had a Maytag smoothtop stove for over 20 years. The only drawback has been when someone left an empty pan on a hot burner. Some of the pan melted to the top which could not be removed. I have to get special pans to conduct the heat, too. Overall, I love it. It has a self-cleaning oven, too, which is a bonus.

First off I dont usually spend my time writing complaints; however, I feel Maytag is deserving of my complaint. Purchased dishwasher Model #mdbh979sab1 in 2013 and days before the 1-year warranty was up the front control panel quit responding, rendering the appliance useless. Got that fixed under warranty. Now about 1 year later guess what... Its got the same problem. Began to read others post on this site and found that this is a common issue. One person posted that her dishwasher began to smoke and nearly caught her home on fire. Maytag was kind enough to offer a paid service call and enrollment into their extended warranty program. I think Ill cut the umbilical cord on this one and go get something more reliable and doesnt pose a potential fire hazard.

I bought a Maytag front load washing machine. We paid $1,100 for this machine. About a month ago, it was making a loud noise. I called them and they said were going to come out and fix it. However, our washing machine did not have a serial number. It had the model number/purchase date, etc, but no serial number. Our drier had it, but not our washing machine. All Appliances stated they could not help us until we had a serial number. We spent around 3 hours on the phone with Maytag, trying to get a serial number. Melinda informed us that we were out of luck, and that there was nothing they could do for us. She stated to call Nebraska Furniture Mart, to get the serial number. We did. NFM does not keep serial numbers. They keep model numbers, and purchase dates, but not the serial number. I called Maytag back, and spoke with Arthur. Within 10 minutes, he gave me a serial number to use. Interesting. In the meantime, I have been without a washing machine for 2 days. I have a load of wash in the machine, because now the wash machine has gotten so bad it is shorting the breaker, and not allowing electricity to the machine. This caused the front door to lock and shut down. Inside the washing machine is a load of clothes. All Appliances now has the serial number to order the parts. The parts were supposed to be here yesterday, Jan. 9th. Surprise, they are on back order until Jan. 13th. I called Maytag to see what they could do regarding me without a washing machine for over 5 days, which could turn into 2 weeks. They simply replied that it takes time to order parts, and there is nothing they can do and apologized. I asked what about me having to go to a laundromat and sit for hours, doing laundry. What about sending me out a loaner, to do laundry until you can get the parts. They again replied; there is nothing they can do.I also stated I spent $1,100 for this front load top of the line, Maytag washing machine, because of its name, and supposedly good quality. They again said there was nothing they could do. They did tell me that the washing tub, the part that we needed, was on back order until January 28th. This puts me at about a month without a washing machine. They stated they would try and locate the part, and have it sent out to my house, not the appliance company that is supposed to fix it, but my house, so that once I did receive it, I could call All Appliances, and set up the time/fixing of the machine. This has been pure hell! Maytag is a joke. I paid a good price for a supposedly good company/machine. They are doing nothing to expedite the parts. They are doing nothing to back their products. They are not even offering compensation for my inconvenience of having to go to a laundromat, or being without a washing machine for over a week, and potentially up to a month.I have been without a washing machine for over a week. I have had a load of laundry locked in the washing machine. I have had to drive to a laundromat to do laundry, which includes time and mileage. I have been informed that the parts are on back order, and now could be up to a month without a washing machine. Maytag is not offering any compensation, no loaner machine, no replacement. Instead, they are just saying, sorry, you have to wait for the parts. I would really like the VPs. and Presidents of Maytag to go without a washing machine for a week, or their families to go without a washing machine for a week, possibly a month, and see what they have to say about that company.

My Maytag dishwasher is a nightmare. I purchased it in February 2013, started having problems with it turning off a week ago. I called Maytag customer service on Wednesday and was told I had a service call scheduled for Friday. I took the day off of work to be available for the repair service. I was given a phone number for the repair service. By noon I was wondering when I would receive a phone call to let me know when the technician would arrive? Then I was told that my appointment was scheduled for next Tuesday... ARE YOU KIDDING???? THAT WOMEN FROM MAYTAG CUSTOMER SERVICE LIED TO ME ABOUT THE DATE OF SERVICE!!!! I spoke with Scott, customer service representative (manager) and he told me that I was sent an email with confirmation. ANOTHER LIE!!!! I HAVE NOT RECEIVED ANY EMAIL FROM MAYTAG. I would never buy another Maytag appliance.... They DO NOT STAND BEHIND THEIR PRODUCTS. LOUSY CUSTOMER SERVICE... SUB PAR TO SAY THE LEAST!!! Very dissatisfied customer - wasted my time and are not willing to make it right.

Bought Maytag Bravos from Home Depot in Dec 2010. Wife didnt like the way it cleaned clothes right from the start. It wouldnt get clothes as clean as her 20+ year old washer. 2 1/2 years later and her $900 washing machine needs $600 in repairs. My wife will finally be happy with the way her washing machine cleans again because we are purchasing a new one this week, and it wont be a Maytag.

After reading all the reviews I realize this is a wide spread complaint. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. You press the keys and hope for the best. I am thinking of going to the media with my complaint. Maybe we will all get some sort of refund or upgrade.

I purchased a Maytag dryer several years ago, not a fancy one but just a plain simple dryer (model number MDE2706AYW). Thank goodness from the other complaints I have read I didn’t buy one that is computer controlled. The heating element has burned out twice, main thermostat and limit thermostat has burned out, and if you look close, it seems the wires are trying to melt or at least the insulation. Well, the insulation is melting. And the venting system is cleaned regularly so they can’t blame that. The last dryer I had lasted well over ten years with zero problems. I should have just fixed it. I’m sure I wouldn’t have spent as much money on repairs as I have with this one. You remember that lazy Maytag repairman that was on TV for so many years, you know why you don’t see him any longer? He is at my house repairing my ** dryer! You never, never hear me say this but the next dryer I buy will be made overseas. My last appliance purchase with any of these name brands on them: Maytag, Jenn-Air, Amana, Admiral, Crosley, Magic Chef, Performa by Maytag, and Norge.

My old washing machine was about 25 years old but still doing a fantastic job getting the laundry done. When the dryer died we decided to replace both machines so theyd match. I had been setting money aside for years in preparation for this purchase. Ive only had them for two weeks and I stay awake at night wondering what GENIUS decided you can get clothes cleaner in a tablespoon of water than you can in an adequate amount of water?! My old washer could wash a load of laundry in about 20 minutes. Again, what GENIUS decided taking over an hour to wash a load of laundry in a tablespoon of water was a better way?! What working woman would choose to double the time needed to do laundry and then not feel confident that the clothes are clean?!!! I am so mad and frustrated and disappointed and I dont know what to do. I wish I could yell at somebody!!!

Purchased a Maytag smooth-top range about a year and a half ago. Ive only cooked frozen pizzas in it. Have only had it on six or seven times. Havent used the top burners at all. Its an electric range, and I just had it hooked up a couple of months ago, as I was trying to find a place for it in the tiny kitchen. The folks who lived here before me, had a huge refrigerator and gas stove right next to each other, and I didnt want to go that route. Anyway, I went to put yet another frozen pizza in the oven, and the light doesnt work!So, after only six or seven uses, the oven light is busted! My mom had an old Westinghouse Terrace Top range, and it lasted well over 20 years with no problems. The only reason she sold it was because she remodeled her kitchen. It still worked great after all those years. Its after-hours now, but when I call Maytag tomorrow, Im expecting to get the run-around, if the other reviews are accurate, and Im SURE they are. Wont ever buy another Maytag product again.

We purchased a Bravo Maytag series top load washer from Sears in June 22nd 2013. See receipt for verification of sale. It seemed to be alright and we were hoping to be a lucky consumer, but now it is January 2015 and today I could smell smoke along with a weird smell (like an auto repair shop smell). I immediately was concerned about the entire house catching fire. Luckily I figured out the smell was coming from the washer and was able to pause it, stop, and then turn off. We are not happy. Our whole main level smells awful. And Im pregnant so this is probably not good to be inhaling. We are looking for recalls that may be out but weve only seen front load recalls not top loaders. When we bought this it had great reviews, but now it appears there are so many complaints, so my question is: Why isnt Maytag doing something about this massive problem?

Does not clean laundry, leaves dry untouched spots, all my clothes look unwashed & the rinse is terrible, leaves dirt on clothes due to little water in cycle. Im a senior on fixed income. I cant buy another machine.. I called Maytag within a couple of weeks of using washer. They told me We have No guarantee for Customer Satisfaction. This is a complete scam on their part. If I could of afforded a Lawyer I would of taken them to court. They knew what they were selling & somehow got away with it. Give the people what they pay for, not the Bravos piece of Junk. Can only wash on 1 cycle to get wet wash. But paid for other useless cycles. Who made this machine & who allowed it to pass to the unfortunate Consumers. If anyone can help getting Payback from Maytag, Please let us know... Better business Bureau should get after them.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

The machine started having issues within a week of purchase. The current issue is, when running the clean cycle, the washer becomes stuck in a mode where it is constantly adding and duping water down the drain. First time it happened, I started the clean cycle before going to bed. In the morning the machine was still in the clean cycle. Running water in the tub and pumping back out down the drain. The water heater ran all night, as the washer was filling and draining the tub at the same time. Each time we attempt run the clean cycle, the washer locks up in this mode.This is the only issue I have had. Many people complain about wrinkled clothes and I agree. I take each garment out the washer and shake it out before putting it in the dryer, this makes a huge difference. Just remember, this is not your mothers washer. It does a great job at cleaning the clothes and saves many gallons of water a month.

I had no issues with my washer. The best thing I ever did was stop using Sabrina softener in it and made the switch to vinegar. The worst thing I ever did was think that paying $900+ for a nice washer would get me more than a year! What a joke! I started noticing small leaks when my hardwood floors started lifting and once my husband looked into this, we realized there is no seal around the top of the drum. So there is no barrier between the drum and your floors basically. Then one day we had a flood. As we watched the cycle run, we noticed that when the water was filling into the bleach and fabric softener compartments it was coming in at such a high rate, it was spilling over the sides down to the floor. So we went to the internet and found a few complaints about this, but no answers. Thankfully we found one guy who had the exact same problem and even had pictures that matched ours. Luckily a real appliance tech answered him and he couldnt even figure it out but took a guess at what I might be: the water inlet valve. But that was just a guess. So we called around to find the part and talked with a few sales persons. One was so nice to even ask a technician standing in line. And he said that there was no way this could be it. But then we decided to take a gamble. We also noticed that both compartments were filling up at the same time, but the bleach should fill during the wash cycle and the fabric softener during the rinse cycle. So it was either the $104 water inlet valve. Or the $200+ circuit board. These are my options after already spending $900+.. So we went with the valve and thank goodness it worked!!!! It is so disappointing that after a short time, this washer broke and cause more damage to my floors. It is an awful design. I bought myself the nicest front loaders for my first house. When that broke 7 years later, I bought this washer because I liked the no agitator design without the smell of a front loader. Now when this one breaks again, Im not buying another HE machine. The majority of people I talked with today said that these HE machines are breaking down faster and faster as the get better and better. I am so beyond disappointed, angry and in shock that this washer failed in less than a year and a half time. My hope is that this review will give the answers we couldnt find without paying an arm and a leg. Is this what passes for quality these days???

Bought this washer back in March of 2016. This is the biggest piece of garbage that I ever came across! That washer does not clean clothes, when they are dirty. If I stand in the rain dressed in dirty clothes, they get cleaner than in the washing machine. In 5 month I have tried every possible variation of washing to no avail. I have to handwash the clothes that I wear to work in the garden, or any other dirty job, because the washing machine does not do the job! I bought that washer at ABC warehouse, I paid almost $400 for the thing, and I have to handwash my dirty clothes!!! Shame on you!!!

We currently have had our Maytag washing machine for approximately 15 years. The first thing we noticed was how user friendly it was. Also, the options that came with our washing machine met all of our needs. The second thing that we were excited about was how quiet it was. Our previous washing machine could be heard at the back of the house and was constantly out of balance. The third thing we noticed was how much cleaner our clothes were. Our clothes smelled better and had less wear thus saving us money. Speaking of which, the machine is an energy saver. One of the most significant attributes I can attest to is how reliable it is. There has never been an issue that required repair services. I am sure our Maytag will be in service for years to come. c

Wow, my dream oven, or now nightmare! I purchased a Maytag dbl oven MGR6775BDS in 2007. The top oven stopped working first after about 3 years and this week, the bottom. I cooked a meal on Monday and Wednesday. Without notice, it would not go past pre-heat. I have called several people and they all act as if this was a truly unique situation. Since I have been out of work, both my regular and extended warranty have expired. I had good faith in a product that carried the name Maytag and the fact that it was on sale for $1,200. I didnt know I had so much company. Yeah, I was told I could purchase a repair warranty for the sale price of $340. Oh yeah, I replaced a 20+ year old oven for the new and stainless dbl oven of my dreams.

The oven hasn’t caused any issues. It’s beautiful stainless steel and black finish creates a shiny but modest finish to my kitchen. It’s self cleaning power is also useful and saves time and where I come from time is money. It cooks food evenly just as an oven should.

I bought my Maytag Quiet Series 300 about 6 or 7 years ago. About January this year the clean light quit working but the dishwasher was still doing its job. Every once in a while the clean light would come on again and then go away. I did not worry about this as the dishwasher was still working despite the absent clean light. I did call Maytag and told them about this. I believe I even asked if they (customer service rep.) had heard about this and was told no. Last Friday the start button no longer works which means the dishwasher will not function. Some of the other lights/buttons work but not start or clean. I have dealt with Maytag repair service/customer service before about my Maytag washer. I know they are not much help and I always end up paying a lot of money. I am not interested in calling a Maytag repair person in and paying from what 300.00 to 400.00 dollars to get it fixed. Past experience of others seem to prove that it will break down again. Last Maytag appliance that I will ever buy. I used to be a loyal customer. I want to join the class action suit. Please tell me how I can join.

We have had our Maytag dishwasher for more than two years. Heres how it stacks up: Energy Star rated-Yes; Noise-Almost inaudible except when water runs; Length of Cycles-long except for quick wash 59 minutes; Interior design and loading - 10 out of 10. This is the easiest dishwasher to load and it holds an enormous amount of dishes of all sizes and shapes. Adjustable and removable racks-Yes both. Everything fits including my barbecue and oven racks! Amazing. Stainless interior-Yes including silverware rack. Cleaning- 10 out of 10. Even on a quick wash (59 min) cycle this dishwasher cleans everything! I run a longer cycle just to sanitize if we have sickness in the house. Otherwise it is 59 minutes to finish. Drying-Like most dishwashers this one is only so-so in the drying department, especially on the short cycle. Without plastic containers or utensils the machine dries more completely. However, the amount of moisture remaining after a quick or regular cycle is minimal. The water tends to pool on bottoms of glasses and plastics mostly. Easy to dry by laying a cloth across top rack. Dries in just a few minutes.My only suggestion to Maytag is to work on drying technology to make the machines more efficient and effective. However, that being said, I wouldnt trade this machine for any other. It has every feature I love and a 10-year warranty on parts as well! My machine cost around $600.00. It was neither the top nor the bottom of the line.

Bought Maytag dishwasher 2007 at Lowes. Model mdbtt60aww-37837606ll manufactured in Benton harbor, Michigan. First got a recall that something was faulty, could cause fire, needed replacement. Took 2/3 weeks to get repaired. So couldnt use. Never quite cleaned good - many times had to rewash silverware, glasses. Never took off food unless very well rinsed. Today the control panel went. Called a local repair he said, Dont even fix. Toss and get a new one because its too costly to repair. I asked what should I get. He said no GE, they are getting out of appliances, no Samsung. Hes got whirlpool so guess Ill give that a try. In the past Ive had dishwashers 20 years, appliances 20 years. This junk lasts a year or two. Plastic cracks. None of these appliances are great anymore. Doesnt matter who you buy. Someone needs to get some quality control on what these companies are peddling .

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

I have been buying Maytag washer & dryers for 40 years. Have always been satisfied until now. The first 2 sets of washer & dryer were great. Very little ever went wrong. Now I have purchased another set approx. 3 years ago. As of today, I will be putting approx. $300.00 in repair to the washer. Repairman said it is a bad design. It is the second time for the same problem, which was repaired a year ago! I will not buy another Maytag product if they cannot be reliable. I should not have to pay $300.00 in repair for a 3 year old washing machine. I am very disappointed.

Weve always bought Maytag, but this is our last time. The washer is just a piece of junk. It uses very little water and the agitator does not work. The clothes end up at the bottom in a ball. The water level is so low sometimes my clothes arent even wet. As I type this it has been stuck in the rinse cycle for 2 hours. It just keeps repeating. Maytag should have to replace everyone of the BRAVOS XL washers. I am no longer a loyal customer. I might as well go down to the river and beat my clothes on a rock. At least they would be cleaner. Shame on you Maytag!!!

We bought a Maytag refrigerator (single-door) with a top-loading freezer that failed after four years. The freezer began to ice up and two repairmen from the company that does the extended warranty repairs in the Ottawa area were unable to figure out the problem. After the second visit, the freezer iced up again and the thermostat appeared to be failing. Even though we had an extended warranty, we just gave up and went to a different dealer to buy a new refrigerator that could be delivered within three days - and it wasnt a Maytag or any other of Whirlpools brands. If youre thinking of buying a Maytag refrigerator, you should reconsider. In fact, you should twice before buying anything made by Whirlpool.

I purchased the Top Loading Maytag Washer and have had nothing but an awful experience with this washer. The dark clothes come out with soap on them. I then need to take a wet towel to wipe out the soap stains. I have had a repairman in 2 times so far and there is nothing he can do to fix it. Maytag said I must wash all the towels with towels, all jeans with jeans, roll clothes into a loose ball before putting in machine, use the extra rinse cycle and the longest wash cycle and do not load clothes more than 5-6 inches high in the tub plus 7 other things I must do to get a clean load and none of those things have worked yet. If the salesperson would have told me all this, I never would have purchased a Maytag and nor should you!

Maytag Washer and Dryer XL Bravos - The worst machines ever. I have had many washers and dryers and every one of them were good enough to get my clothes clean and dry without wrinkles. This washer Maytag Bravos Washer and Dryerdoes not clean clothes no matter which setting it is on. The dryer does not dry the clothes without wrinkles if it dries them at all. They are only about 6 months old, I have followed the book on usage and it still doesnt help. If I could pick these up and put them at the curb I would. If Maytag would take them back I would return them. Buyer beware.Updated on 03/17/2018: Maytag wrote to me and wanted me to give them my contact information along with any other info regarding their appliances. Still havent heard from them, and I assume if I do it will be like all of the other replies, Sorry for your inconvenience yada, yada, yada. I did check online for Lemon laws for appliances and there are laws for the consumers to fight the companies. If and when they contact me I will be sure to mention this to them for what its worth. I think a class action suit might be the answer for all of us consumers. If banding together would help count me in!!!

The Maytag Bravos XL Gas Dryer I purchased less than a year ago has stopped working three times. The dryer stops producing heat. I am now about to call Maytag repair again and waste time and energy setting up a warranty service call. I spent a lot of money in order to go to the Laundromat on a Sunday. Do not purchase this dryer if you would like to be able to dry clothes at home with any type of consistency or confidence. Arrrggg!

Im totally done with the Maytag brand that Ive trusted for over 30 years. I never knew until yesterday via Facebook friends that they are not true Maytag-made anymore. They were bought out by Whirlpool eight years ago. I bought my top-load Maytag Bravo 400 Series Washer ($1,028) at Home Depot in October 2008. No problems with it until now, less than 4 years old with error code DL. So I looked in the book and found it was the lid lock (the little red light wasnt lighting up when closing the lid, which prevents it from running).I made an online appointment with Sears Home Appliance repair to check it out. But after talking with online friends and googling fix videos, I was able to get it running today by taking the top off, unplugging the lid wire and plugging it back in. So far, its working but now I will fear each time I go to use it that something else will fail. My old Maytags (washer and dryer) bought in the 80s never needed service until they approached the 14- to 15-year mark. That only tells me that the newer made appliances are total junk! So many complaints and how the companies dont back their appliances, it just sickens me.

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

I purchased a Maytag washer-dryer combo in late July 2014. It wasnt until early August that we actually used the washer. It worked fine the first day, but the next day it would no longer fill. After following all of the troubleshooting instructions, I called Maytag to schedule a repair. They said they would locate an authorized tech to make the repair. I called back the next day and was informed that there was no repairman in my area and they would contact a service that contacts local repair techs. A few days later I called back to learn that they still could not locate a repair tech. I live near the New Mexico/Arizona border, and asked if a service tech could travel from Tucson, Arizona and was told that they could not cross state lines and, at that point there was nothing else they could do. They claim that I live in a remote area, but I reside near a major US Interstate (I-10). I will be filing a complaint with the BBB and my states Attorney General. It is now late October and all of my efforts have been ignored. I am totally disgusted with Maytags customer service.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

My wife told me yesterday she was getting a f51 code... went on you tube and took the top off and the clothes holder out, found 1 quarter and 3 dimes... put it all back together... same thing... took the back off... hoses off, unplugged it and the allen that holds the motor had backed out... no more maytags for me... Tightened the allen, all is fine for now... my opinion, this should never ever happen... No lock washer anything engineering to prevent this from occurring... My grade: replace the engineer...

We have had washer/dryer Bravo Series and been nothing but horror stories. Washer bounces all over room to point hoses come out and flooded my laundry room and foyer and garage. It takes over 1hour 45 minutes to do loads sheets which is 2 sheets 2 pillowcases. The repair man told me that takes that long due to MY sheets are dirty. I have been married 46 years and never heard that ever!!! The dryer is just as bad, takes over hour and half to dry sheets and towels almost 2 hours to dry. DO NOT BUY MAYTAG ANYTHING. The person who said needed hurricane straps to hold washer is something I agree with. Just a horror.

We bought this Maytag MFI2269DRM01 Fridge/Freezer in June 2016. We have nothing but trouble. First the center rail holding up the Fruit/Veg drawers snapped within a month then the freezer drawer would not close properly which gave us all sorts of problems (door open lights flashing and fridge staying on longer. Lights not working etc.) The service tech came out and tried to fix it and went away saying it was not repaired that he would need a new freezer drawer. In the meantime I had to push the drawer to try and get it to work right. Now the handle is loose and the stainless steel front of the drawer is damaged by pushing it in so much.This repair started in November and now it is the end of March. I asked them to replace the complete unit but they say that the warranty is just to repair. It seems like they have no parts to fix this. Then the new center rail snapped again!!! When they sent the part out to me to install, I found the main frame of the Fruit/Veg rack at the back had snapped. Everything is brittle plastic with not enough support. (The only vegetable that I think I can put in the drawers is mushrooms.) I thought by buying a Maytag that the name sold it. What a piece of junk it is!!! Will never buy another Maytag product!!!

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

I bought a Neptune Washer in 1999. 6 years later (2005), it started making the 747 landing noise. It was implied that somehow it was our fault, maybe, something from my contractor husbands pocket. After all, it was a Maytag, and surely there could be no design or engineering flaw! (My daughter still has 34-yr.old one.) We were told the repairs would be so expensive. It would be wiser to buy a new one. Foolish me, I bought another Neptune to match my dryer. Of course, now this one has the same bearing problem and again its cheaper to buy a new washer. I am angry and not sure how to proceed. Any washer, but especially a Maytag, should last more than 5 - 6 years. I should not have to buy my 3rd washer in 12 years. And if I do, it certainly wont be a Maytag!

The salesman tried to convince me to purchase a Bosch dishwasher, but I wanted one with a fingerprint-resistant finish. That narrowed my selection to several manufacturers. This dishwasher has a food grinder in it. It gets my dishes spotlessly clean, and I have been very happy with it.

I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

I would like to say that I purchased the Neptune washer & dryer for my parents back in 1998. Up to now, 23 May 2015, not once has either of the machines required service and have been functioning well for the past 17 years. This is a testament to the quality and workmanship that is Maytag. This week I have purchased the Maytag Maxima front loading washer & dryer for my home because of Maytags reputation.

We purchased our Maytag Bravo XL in 2012. Over the past year and a half we noticed the inside of the top lid is rusting as well as the bleach dispenser area. I called Maytag about the lid and they said there was nothing they can do and that we could buy a new lid replacement. Really??? My parents had only Maytag in their home for over 50 years with little to no repairs needed ever! We were a family of five back then. Because my parents always bought Maytag products so did we. This is the first time in 40 years that I have ever seen this happen! I was hoping for a recall for these issues but dont find any online. The washer and dryer were not cheap and purchased from a reputable retailer.

Purchased Maytag Model MVWB865GW0 Ser# **, had it ONE year, circuit board and switch have gone bad, will not turn to change the type of wash cycle and the lid will not lock, which makes the washing machine not start to wash. Contacted Maytag to request a service call, per the service team the circuit board will cost $300, plus a switch $75 and Labor $100 plus tax. We will be better off buying a new washing machine! We should not have this high cost within ONE year of purchasing! Will not purchase a Maytag again!

Maytag Centennial Washer - If a wash load becomes off balanced, the machine stops. No signal or buzzer or anything to alert me to this. It happens all the time and wastes a lot of my time. Here I am thinking that the wash is going fine only to find out 2 hours later that it has stopped. Anytime I wash more than 3 items, this happens. I will never buy one again and I am telling everyone not to buy. I will be purchasing a good old fashion washer with a dial gauge so I can spin it any time I needed.

We renovated our kitchen in 2008 and installed all Maytag appliances. We had purchased a Maytag dishwasher 3 years prior to the renovation-- that we kept. Well, the dishwasher was the first Maytag appliance to go. After replacing several cheap plastic parts on the dish racks (I resorted to use twist ties at one point to hold the racks together) the racks started to chip and rust, leaving stains on our dishes. The cost to replace the racks was about $150 so we just replaced the dishwasher (with a Bosch - so far, no problems!)Then, a couple of the igniters on our gas cooktop stopped working. Since they were the back burners that we didnt use much, we just used a match to light them and let it go. Next, one of the hinges on the double wall oven door snapped. This is a little concerning because the doors are heavy and will need to be replaced. And the final straw concerns our French door refrigerator. The control panel started flashing wildly and the ice door was opening and closing with a loud clicking sound. Of course this happened on a weekend so I looked online and found hundreds, if not thousands, of similar complaints. So I called Maytag and spent nearly an hour on the phone only to be told that my model number was not one of the recalled ones. I explained that my problem was exactly like the others and was told that the best they could do was offer me 50% off any parts. The service call and shipping would not be covered either. The Maytag representative that I spoke to tried to cheer me up by telling me that at least they had the part I would need in stock, unlike the recalled models. Those parts are discontinued and have to be specially manufactured and have a two month waiting period. The part is about $250 and add to that the shipping and service call and I am sure this is going to cost me several hundred dollars even with the discount on the part. Very, very disappointed. Never again will I buy Maytag, never again!

Like many others, my Maytag Bravo motherboard has stopped working after about 2 years. The clothes do not get particularly clean, it is extremely noisy, and the wash cycles are excessively long. I would not recommend this appliance to anyone.

I purchased a Maytag Bravos HE top loading washing machine two years ago. The clothes hardly get wet enough to get clean. It leaves a residue on dark clothes and the basket goes unbalanced at the drop of a hat. Whatever you save in water, you spend on electricity because a cycle takes twice as long as a conventional washer. It goes out of balance and bangs the machine enough to walk it across a room. I purchased this machine from an appliance store, not some discount house. I have had machines last 20 years and this one is shot in 2. I will never, ever purchase another Maytag, Whirlpool or KitchenAid product again ever.

I have a Maytag dishwasher and the rollers for the racks are failing due to heat: plastic wheels breaking up. $35 each to buy and replace. There are eight total. So $280 because of poor testing and quality of materials. Manufacturers should test to ensure the parts last a reasonable period of time and are designed for the environment in which they are being used.

Bravos washer purchased Sept. 2016. I purchased the Maytag washer based on experience and reputation. I am so disappointed in this washer. I have had the control board replaced after only 3 months and it vibrates, shakes and is very noisy. It does not fill with enough water and the clothes are tangled at the end of the wash. I will never buy another Maytag.

WORST MACHINE EVER! Besides the soap scum Maytag Bravos XL Washer leaves on all of our jeans and my husbands work pants, the machine decides when it wants to work and when it does not want to work. Weve had repairmen over, we have called the 800 numbers, just like all of the other reviews on here. Ive readjusted clothes in that thing more than Ive done laundry in my life!!! I HATE this machine. Ive memorized the manual from reading it so many times, have the correct detergents, tried washing large loads, small loads, lined up the clothes around the outside so the middle thingie is not covered, thrown clothes loosely in there. Every way possible. The machine senses, starts filling, then just stops. Today, no matter what I do with the load in there, it will NOT run, it keeps shutting itself down and I do not even know what else to do. NEVER EVER EVER buy this machine! We will never own another Maytag EVER.

I bought the newest most energy efficient Maytag model M9BXXGMYM00 (for about 1K) from a local appliance store and after 9 months it wouldnt freeze. The local store picked up and left a loner for the fridge and made repairs in shop returning it in a week - great - except that approx. 11 months later the fridge again wouldnt freeze. The store sent repairman who charged 125$ to tell me it had leaked its freon again and would need repairs which were no longer covered under 1 year Maytag warranty. I asked the store to back their work but was only given a refill of the freon and half off the service visit. 2 months later the fridge is not freezing. I know because the repairman and store owner Mike told me that it had freon leak and that Mike himself had made repairs to the leak that the unit wasnt repaired.I have read that freon is toxic and can be hazardous to people with heart conditions and a list of bad effects. Maytag will only send someone to repair unit for a service call charge plus the repair charges and will not replace a defective unit. I can take the appliance store to small claims court over faulty warranty repairs but probably not the health risks - which are disputed by the experts. Ive read reviews and have heard from people who have appliance issues that the companies basically use a defective unit as a cash cow sending repairmen back again and again and never fixing the problem making a lot of money off of frustrated people who have bought a lemon from a company who doesnt back their product or their work. I was only looking for a decent refrigerator and paid plenty for one. I now have to get rid of a nuisance or pay to fix it - probably more than once and spend lots of time getting through the court vs. store owner process for any of the 1000 bucks lost on the defective toxic junk I got from Maytag.

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

I had my Maytag washer and dryer just barely over 30 days. My washer sounded awful and I had to get a new motor. Then my clothes would come out with dry spots. Not enough water. The computer was replaced and within a few months of purchase, all the major parts of my washer were replaced. I hate it! My clothes still come out with dry spots and it is loud. Worst major purchase I made. Dryer so far has been ok.

I had the microwave serviced and they heated a cup of water which was fine. I heat food on the tray and only one side gets heated. I have to turn the plate to heat the rest of the food. I never had that problem with a turntable microwave. I cannot understand why they are still selling this inferior product. Maytag used to have excellent products. What happened to this company?

I purchased both a Maytag Neptune washer and dryer in 2007. This is without a doubt one of the biggest mistake I have made. I have had the dryer drum and rollers replaced and the washer will no longer run. It is going to cost me hundreds of dollars to repair. To think I bought these units for 2 reasons: 1. that Maytag are the dependability people, but its not! and 2. Energy efficiency. It is not too efficient when they are broken more than they work. The worst was when the repairman told me that I had purchased the worst product on the market. These units are in short, garbage! I will never buy another Maytag Product!

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

2 Year old washer. First the actuator was replaced. A 150.00 charge. Two months later the pump is shot. Another 200,00 to replace the pump. This is worst piece of ** washer I have owned. I would not recommend to anyone. Stay away. I would give it 0 stars if I could.

The washer machine is only 2 years old and its broke, at first it wouldnt spin and now it wont wash. Everyone is saying between the parts and service fee, it will cost 200 to 300 dollars or more to fix, most technicians wont repair them because they say that we may as well cut our loss and just buy a new one. No one likes these machines. I wish I would have known what a sham the washer machines were before purchasing.

I purchased these appliances on 02-10-16 from Home Depot in Loganville Ga., for almost $2000.00. I filed the first repair call less than 3 weeks after delivery. The sensor panel was bad and had to be replaced. Now 8 months later the washer is not starting, AGAIN. The dryer will only dry one load a day or you get the AF code. This means that the dryer cannot push air over 5 or so and we need to have a vent booster fan (an additional $200.00) installed plus have an electrician run a new outlet. I returned to Home Depot with my complaint. Feeling that I have an inferior product, they tried to get Maytag to make it right. Maytag refused to offer any solutions whatsoever. Home Depot refunded a little over $300.00 for my inconvenience.The washer is an absolute ill-conceived piece of junk. It is ROUGH on clothing and does not remove soap. I started out with brand new (expensive) towels when I purchased this machine and 8 months later all of the hems have been snatched off and theyre unraveling and falling apart and are slowly becoming car wash towels.You cannot wash delicates in this machine and allow it to spin. Underwires in bras are badly misshaped or broken completely. You cannot wear them afterwards without being gouged by bent wires. The only way around this is to take away the spin cycle, but you better be ready with a clean garbage can to haul the dripping clothes elsewhere and hung up to drip dry. The washer has NEVER removed all of the soap from bed sheets. I have a dark gray set that show the soap best. Now I have to wash once with soap then wash again with no soap. This negates the machines being efficient.Unfortunately, I found the negative reviews AFTER buying the machine. My complaints are well known to Maytag, seeing has to how the same complaints are found online as far back as 8 years ago. I have been brand loyal for 30+ years to Whirlpool and thought that I was moving up with a Maytag, based on my parents 50 year experience... I was wrong! I will never purchase another Maytag product nor Whirlpool since Whirlpool now owns Maytag. I have researched and am of the opinion that Speed Queen is a far better product and plan to junk this set and replace them with Speed Queen.

I have a Maytag Bravos high energy machine that Ive only had for 3 years that has stopped working. After the cost of two diagnosis visits, estimated repair costs are $734 - more than I paid for the machine. As explained to me, these high efficiency washers are in their infant stage, especially when I bought mine in 2010. I feel I have no recourse except to buy another machine. It certainly wont be a Maytag or Whirlpool model! I did research the machines at time of purchase. I thought I was buying a top reputable brand. Guess I was wrong.

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

Bought this as W/D set brand new from Home Depot. Had been noticing incredible wear and tear on clothes, as things get so tangled up and need to be practically ripped apart before going into dryer. Cycle times are crazy long, up to over an hour in some cases. Doesn’t have a “Speed Wash” cycle. But WORST of all, after less than 3 years, it just stopped draining properly. Tried all the Codes test, etc. Finally called a repairman just to be told repair costs would probably cost more than the machine is worth. $125 to be told we ought to just buy a new washer. Not happy.

Purchased the Bravos XL top load washer a month ago. We work outside daily and our clothes get very dirty. I havent really taxed the machine yet (Im doing what I consider a normal load of wash. I know the machine could handle twice as many clothes as its the 5.3 cubic feet washer, but I havent had that many clothes to put in at one time). The washer works great. Clothes are clean and smell fresh. For those that say this washer is extremely loud - you must not have something set up incorrectly. Either the wet pan you put under the machine is making contact with parts it shouldnt or someone didnt level it properly. Really, this is NOT a loud machine. We purchased from Lowes and they delivered, set up and leveled both the washer and dryer. (Yes, we also purchased the matching Bravos XL front load dryer and were impressed that it dries our clothes in half the time our old one did). We would definitely recommend the Maytag Bravos XL washer and dryer.

We bought Maytag refrigerator MTB2195 AEW in 2006 for a hefty sum. The store where it was purchased was closed. The place where it was serviced was closed. We have had seals replaced, fixed, etc. twice. The freezer is full of ice balls hanging. The refrigerator doesnt keep as cold as it should and stays steamed on glass. I had a repairman again today and was told that he cant fix it. The frame will not stay tight. Theres a 3/8 in. drop from left side to right. It cant seal properly. You have always been a great product. Whats happening here? What can you do for me; Im at wits end. I have an older refrigerator in the basement thats 26 years old and is still going strong. I need something done quickly as I dont want to wrangle with this ice any longer and shouldnt have to. Please give me your attention on this as soon as possible. Kathy

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.

The washer doesn’t have enough water to to get clothes clean. Even on deep water wash there’s is not enough water. It doesn’t get clothes clean, its very noisy. It takes a long time to was, even on short cycles. You can’t soak dirty clothes, it has a cycle for soak but it is not long enough. After about 3 months the lid licking doesn’t work and the progress lights remain on and never go off. This is the worst washer that I have ever owned. I just want to return it and get a different one!

On the 11/25/16 bought a refrigerator at Home Depot. Beside that the first was not called off, wait for another month 12/31/16 for the other refrigerator the problem are. I file a complaint because Maytag left me a message refrigerator half a price. Now they deny when I have proof.

We bought this refrigerator one year & 3 months ago & we have had various issues that are now no longer covered under the warranty. The pantry drawer has a peg on the side that is plastic & broke off on the right side. Will have to replace the whole right side panel. One of the door handles is coming loose which should be an easy fix, but its just annoying that it happened at all. Now the control panel is reading OFF/OFF & isnt responding at all. Tried unplugging for 10 secs, then plug it back in, but no luck. I cannot find any info online regarding this issue, so we will have to call Maytag. Hopefully, there is an easy resolution to this problem & we wont have to buy a new motherboard.

Model MDB4949SDZ0. 7/10/2018 Purchased from Costco. 7/23/2018 Installed by company arranged by Costco. 6/18/2019 A burning smell was coming from front control panel area of dishwasher when it was turned on. 6/25/2019 & 7/3/2019 Repair technician came to fix but could not find anything wrong so burning smell continued whenever dishwasher was one hour into cycle. 7/12/2019 Repair tech changed out front control panel because burning smell was still coming from handle area. 8/9/2019 Dishwasher does not drain completely when wash cycle is complete. Sometimes there is sudsy water left, sometimes it is clear. The water level is above the heating element at bottom of dishwasher.We only run the machine 2-3 times a week and have been using different cycles to see if the draining issue is with one cycle or all of them. No matter which cycle is used, water remains at the bottom of the dishwasher above the heating element. This seems like way too much residual water. Repair technician is scheduled to come for the 4th time to look at dishwasher but we just received a message that we will have to pay $129 service fee because dishwasher is now out of warranty. Maytag, fool me once, shame on you. Fool me twice, shame on me. Therefore, know that we will not be purchasing a Maytag product ever again.

After buying this dishwasher model MDB6759WWW3 in Jan. 2010, I fully expected it to work longer than it did! So far, the control panel has been replaced 5 times. The last time was Sept. 17, 2012 and already it is out again. I talked with Customer Service, since Georgia has a lemon law. After 4 times it is to be replaced.They had no record of the part that was replaced, just that a technician had come and repaired (by ordering the same part they had no knowledge of). This time they will either replace or instead of me calling, my lawyer will call. I will never buy another Maytag product and will encourage anyone else not to buy either. My daughter had the same experience with a refrigerator, a piece of junk they did nothing about. By the way, I have an extended warranty plan, which should not even be necessary!

This is the best microwave that we have ever purchased. I especially like the baked potato choice. Its also very easy to use and clean. I would definitely recommend it.

Bought a dishwasher about 2 years ago, through Home Depot. After it was installed, contacted Maytag to let them know that it didnt seem to be working correctly. They sent out a repairman, who looked at the machine, and then told us that with the new eco friendly settings, it would be best to let the dishes dry overnight. It seems that the company and its employees dont know [or care] about the product. Contacted their service/helpline to let them know that the screws on the insides of the latch [on the cover] are NOT screwing into anything, they come loose. Person couldnt find same in his system, finally sent screw, but they were the wrong size and didnt work. Just opened the dishwasher this AM, after washing the dishes last night. 12 hours later and they still are not dry. This isnt eco, this is something that is wrong that Maytag doesnt want to address. Buy something else!!!

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

The ceramic coating on the interior of the oven cavity in the top oven, which I use the most (may actually happen to the lower oven in time) has cracked in the exact pattern of the hidden element. When I spoke to the salesperson at the store, he wasnt surprised and said that it will eventually bubble and rust!!! Called customer service and was informed they consider this an aesthetic issue with no fix!!! They will not offer any remedy or compensation. Are you kidding me!!!

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....