I bought Maytag frost-free refrigerator last August 2006. But now, I noticed that ice builds up in the freezer. The product is only five years old but I was told by Whirlpool that they had discontinued making defrost heater. The reason why I bought Maytag was the ad on TV showing the Maytag service technician seating and doing nothing, implying that Maytag brand is a good product. Think again before buying Maytag products.

Model #MFI2670XEM0, Maytag fridge top French doors, bottom freezer. Purchased fridge in May 2011 from Lowes, with a matching microwave. A couple months ago, I noticed puddle of water on wood floor in front of fridge, so I opened freezer to find ice on bottom with a sheet of fresh water on top. Call to Maytag was useless, also tried to sell us warranty. Guess that $300+ warranty would cover one year, so after the warranty runs out, would we have to buy another when it plugs again. Our kitchen floor is ruined, and the warping is coming close to our dining room. Googled problem online to see if there was an easy fix since it was out of warranty. I tried to defrost as described online, only to have it leaking again a couple weeks later. Will never buy a Maytag again. Guess that repairman in commercial is never busy because Maytag wont stand behind their products.

The top loader washer Commercial Technology washes very small loads well. I bought it for the deepwater wash. It DOES NOT work. It also has a auto sensing. Hate this washer. I have to pour buckets of water in the wash to fill it. Maytag/Whirlpool go back to the way it should be. If I want a full washer I should have it! At the end of the day IT IS MY WATER BILL!

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

Purchased a supposedly top-of-the-line Maytag washer and dryer (9000 Series with Steam and MCT-Maytag Commercial Technology; Washer MHWE900VJ). Just under five years of use and the repairman quotes me just over $1000 parts and labor with the overwhelming majority of that quote being parts. No wonder the Maytag repairman is the loneliest guy in town - its not worth fixing your not-yet-5-year-old machine. It kills me that companies are allowed to advertise and promote the quality and reliability of their products and less than 5 years later, the machine is going to the dump, after having paid a premium for quality. This technology was supposedly comparable to what is used in a commercial setting - not very believable in my opinion. No more Maytag or Whirlpool for me.

I purchased a set of Bravos 4 months ago and what a bad purchase! I wish I would have researched here first. Being environmentally concerned, I bought it because it was supposed to be high efficiency and low water usage. My clothes are being destroyed by this machine. They come out in a massive tangled ball, covered in ink and animal hair (after a wash or two, they are completely embedded into the fibers). Sometimes there are dry spots after I take a load out of the washing machine. No idea how that could happen. It torn my favorite sweater, ripped sheets, bore a hole in a towel, ripped pillows, and DOESNT EVEN CLEAN! I have to wash my clothes twice MANY times to get the dirt out which doesnt bode well for energy efficiency. Im calling them again today to try and get them returned for advertising that they will save me money. Not even close! They are a rip off! I gave my 35 year old set away and wish I had it back! Maytag is JUNK!!!

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

All of a sudden, the lid lock light is flashing. The washer is only 1.5 years old!

The Maytag Washer and Dryer we bought new and they have been great. The dryer was bought in 1972 and still works well. The washer was bought in 1997 and still does a good job. We are satisfied with the long time these 2 appliances have lasted. Do any appliances manufactured today last that long?

We bought Maytag Dishwasher on October 9, 2019. Due to the installation difficulties we were not able to install and try it right away. Lowes warranty expired in 30 days, and the dishwasher is not cleaning the dishes. Even with the hand prewash of all of them-they come out dirty. I have to clean them after. The dishwasher is very weak. We contacted Maytag and were told that they can do nothing for us, only send technician (we have to pay $160 per visit). We can not return or replace it, the quality is very poor, so we will have just to buy a new dishwasher and lose 500$ for this product.

Just had the repairman here. This machine is computerized so it won’t last. It does not have a setting that lets me do any load of laundry the way I need to do it. I have to use heavy duty to do a load and then it takes 2 hours. When I want to do a load of sweaters on delicate it will not put near enough water in the machine to wash them. The normal cycle does not add enough water to wash, let alone rinse the clothes. I can’t choose the size of the load based on how much I need to wash so I have to do more loads at 2 hours each or do everything on bulky. Whoever came up with all this needs to be fired. I am extremely unhappy with this machine and I have loved Maytag for years. No more.

I have a Maytag Clothes Washer. Lid Closed Light is flashing and agitator will not spin. Troubleshooting shows when the washer does not detect the lid is closed the agitator will not spin. I went to Maytag Canada website and chose Live Agent. There is no Live Agent! You get a Virtual Assistant that does not work; bad software. Virtual Agent shows connected. I type in the details of my issue and the Virtual Agent responds with No Input Detected. I type in the details again and the Virtual Assistant responds with Connection Closed, try refreshing. Over and over again. Tried calling the Maytag Canada 1-800 number. I have now been in the queue for more than 40 minutes. Just stupid cycling for a recording for common problems dealing with products that are not a washing machine (about a 9 minute cycle). NO CUSTOMER SERVICE. Avoid Maytag, Whirlpool and Kitchen-Aid products. Buy from another manufacturer that has live people working at the company.

I bought a new refrigerator and when I plugged it in would not cool. I called and the authorized tech came and said the compressor was bad and the evaporator was rusted and hoses were greased up. I have now been informed that the warranty was void because it was put in a dental office and not a single home. I said since it was never used I would put it in a house. They said it was void and I was out of luck. I always thought maytag sold good products but this has convinced me to never buy a product from them again. It never worked and the tech said it should be replaced but they said he should never had told us this.

We bought a Maytag refrigerator serial # K11101146 and model # MBL2258XES1 on 5/7/2011. We started seeing puddles on the floor about a month ago coming from the bottom freezer. The warranty on the refrigerator was only good for a year. We investigated it further online and saw that a lot of other people were having the same problem. We found a video on Youtube on the solution, which was to tear the bottom frig apart (which is a pain and takes about 3 hours to complete) and to thaw out all the ice accumulated on the coils and run hot water down the drain until that thaws out. It makes a real mess. Now we see that this will probably have to be done again and again from others online who are having the same problem. We never had this problem with any of our refrigerators or any problem with them for that matter. Our last one was a 15-year old Amana and we wanted a more energy efficient refrigerator. We bought this one at Home Depot thinking that this one would last us for the rest of our lives. We are in our mid 60s now. This should not be happening at all especially as much as we paid for the refrigerator. I contacted Maytag and they more or less said, “Sorry about your luck.” I hope something can be done about this, especially for the amount of complaints filed. Unfortunately I did not take pictures but if it happens again, which I understand from other complaints that it will. Thank you.

We purchased a Maytag refrigerator Model # M1TXEMMWS02 and Serial # E01103420 in April of 2010 from Home Depot in Aurora, Illinois. First off, we did register the fridge online via Maytag which of course, they have no record of! Now, we go on vacation and come back to all of our food ruined because the refrigerator stopped working! No refrigerator should stop working within two years! I called Maytag and they offered me a Repair Plus One package of $302.73! Are you kidding? We paid $400.00 for fridge. Then of course, only one-year warranty and have to pay at least $75 for a service call, labor plus parts! If it’s the compressor, the charge is $326.20, plus shipping and handling! What a joke! There needs to be longer warranty and should offer free service calls and much more. I am disgusted in Maytag products and in which we purchased due to a reputable name! Never again.

Purchased the Maytag Bravos XL washer and dryer in January, 2014. Today, 5/16/15 (less than 1 1/2 years later) the repairman tells me that the cause of the loud noise in the spin cycle is bad bearings. Only a 1-year warranty on the machine. I have never purchased extended warranties on appliances so this will cost me $400! Or a new washer since this is more than half the cost of the new washer. This is bad business, Maytag. Ive been a loyal Maytag customer for years but I think Im heading to Speed Queen with their 5-year warranty unless youre going to give me a helluva deal to keep me. Grrrrrrr.

My built in electric double wall oven, Model MEW6630DDB, convection on the top, has been the most frustrating appliance I have ever owned. It has never kept an even temperature. It has been repaired several times and still does not keep an even temperature. It takes 14 hours to cook a 20 lb. turkey and baking cookies are not even an option. I have complained to Maytag and have paid for repair services. Their solution buy an extended warranty which is absolutely insane because they havent been able to repair it since it was new over four years ago.

We got our Maytag dishwasher in 2011. Weve experienced a lot of the same problems other people have mentioned. Control Panel was the first thing to go out. Now it has a foul odor coming from it and it doesnt get the dishes clean. The heating coil has stopped working and is rusting. This dishwasher is junk and Im very disappointed. I will never buy Maytag again nor any company related to them.

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

Built a new house, bought new appliances for the kitchen. Like others, did all the research, wanted to buy American made. Wow, did we ever make a mistake. Refrigerator is just over 2 years old. It is worthless. Repairman, Maytag Certified, says that it appears to be internal problems and probably come from the factory that way. He suggested I contact Maytag directly and they should be able to make things right for me and my family.So, I called, sat on hold for 10-15 minutes, and was finally connected to a customer service employee. I explained all that I knew about the problem, she pulled the repairmans notes and the notes of the technician that had spoken with the repairman. After reviewing the file, she informed me that my 2-year-old refrigerator was out of warranty and there was nothing that could be done.What ever happened to American Made companies standing behind their product? I didnt spend $2000 on a refrigerator that would last me 2 years. I expected 7-10 years, AT LEAST! I expected a company with the name MAYTAG to show some shame for creating a piece of junk and charging a customer this much money for something they know is obviously flawed from the factory. Shame? No. Guilt? None whatsoever.Caution to those considering a Maytag product. Run away! Go find a more reputable company. Go find a company who views customer service and quality products as a priority. I didnt purchase the cheapest refrigerator on purpose. I paid extra for American made and what I thought was a quality product sold by a quality company. Reality has now set in.

Bought this Maytag Bravos Washer online from Lowe’s in the holiday season of December 2017 because my previous Maytag HE washer broke after 17 years. I have had nothing but issues with this washer right from the start. The clothes do not come clean as I find myself putting them through the wash cycle two or three times to have them washed and come somewhat clean. The clothes come out soaking wet that I have to put them through the rinse and spin cycle at least one or two more times. I called Lowe’s to complain about this washer and they said they only have a 30 day return policy and they would be happy to call for service for me. I told them it didn’t work from the start but they didn’t care. So now, sadly, I have a repairman coming this week to fix my new washer, And hopefully he can fix it that I can use it and it can properly wash clothes. I wish I would have her read the reviews on Consumer Affairs about this washer before purchasing this Maytag. Not happy with Maytag. I would have never bought it and bought a different brand. Codes appear on the face of the washer better. Nowhere in the manual that I had to personally download myself because it didn’t come with one. And oh did I mention that I need a step ladder to reach into the bottom of the tub? This washer should come yellow because it is definitely a lemon!

My Husband bought a Maytag Bravos Washer 2 years ago this next month. The washer is extremely hard on clothes. We have to wash all clothes on hand wash to keep them from tearing up our clothes, and we are having to replace the door lock for the third time. Of course the last 2 times were not under warranty. So once again, I cant do laundry when I need to. Thanks.

We purchased a gas range and over the range Maytag microwave a few years back and have had problem after problem with the microwave. Weve had 3-4, maybe more, repairman here and they replaced pretty much everything. Its been going for about a couple years now without a service call, but it went out again today. Very frustrating when you spend good money on junk. We are now to the point that we either replace it with another brand or we just put in a hood and have a microwave on the counter. Just so frustrating. I would not recommend Maytag over the range microwave to anyone!

The washer 4 years ago we had the control panel replaced at our expense. Now, control panel is going out again. Also this summer I took the dryer apart to snug up some screws that had come lose, that were scraping the inside as the dry ran. I own a range and a dishwasher Maytag brand but will not buy another Maytag unit, even if they are built by my union brothers and sisters.

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

I will never buy another Maytag product. Our dishwasher is not even 2 years old and the control board went bad. No extended warranty was purchased because we assumed that it would last longer than 2 years when our Sears Kenmore lasted 25 years. No help from customer service. We now have to spend over $300 to get this piece of junk repaired.

After the 4th service call Maytag wanted a 2nd company to look at it. So on July 27th A&E out of Bristol, PA came out. He checked it out and said its not serviceable because theres a leak somewhere in the casing. Had to call KYW 3, On Your Side, they helped me get some progress. Jacqueline from corporate called and said they would replace it. It started on July 3 and now August 13 and still no fridge. Had my Maytag washer fixed, small problem. Parts came in a box marked Whirlpool for a Maytag washer from a Sears Warehouse. Plus the mechanic said my Maytag refrigerator is made by Amana. Buy American?

So the reviews for the Bravos MCT online were pretty decent. We purchased our set from Lowes. However, the clothes dont turn over. I watched as long as I could (getting frustrated the longer I watched) to see how the clothes were going to get turned over and washed. All they did was get rubbed on the bottom of the pile where those agitator fins are. But they never got a good flipping so that the top of the pile was washed. I only had 4 normal size towels in there. So it isnt like I had too many clothes.So I called Maytag to tell them what I was observing and the gentlemen explained that it was counter-intuitive technology and that it seems like they wont come clean but he promised me by the time the load was done they would be clean. Yet - they did not come clean! The dirt on the towel was still there on the top of the load with dog hair. NOT TO MENTION SUDS!! Im so disappointed because the burden is on me to either take this set back or deal with it. Buyer beware - if you look at this machine and ask yourself how in the world will the clothes get clean - you are asking a great question! They dont!!

I purchased this washer in January 2017 at our local Home Depot here in Mexico. It was a washer/dryer combo. Now, in July, a mere 6 months and only a few wash loads later, it has gone from the worst machine I have ever owned to what I consider to be garbage material. First of all, it boasts about not using much water. This is true... Only 1/4 of your load is in the 3 inches of water at the bottom of the machine and the top 3/4 never even gets wet. I couldnt believe it. Now, I put 2 sheets in this morning and it fills almost to the point of spilling out, though I have to give it credit for shutting off the water before it actually did so. This is a NEW washing machine!!! I, along with a lot of other folks from what I am now discovering, are all in the same boat. I remember Maytag being a mark of excellence way back in the day... This is no longer the case. Stay away from this company... I know I will.

Bought in July 2014, third service call already! To replace my 6 years old Maytag Centennial thinking I was doing a good thing to upgrade to an HE... HA! Jokes on me! Washing machine: Water level. How can you wash clothes in 1 inch of water??? Noise. Very noisy at every cycle. Shakes and easily unbalanced. Clothes are still dirty after wash (obviously if not enough water). Dryer. Noisy with sporadic blower sound (like a plane taking off - high pitched). Three service calls in 6 months??? 2 calls for cable suspensions and now waiting over a month for the tech to change the drum completely. Good thing that I took an extended guarantee, for an extra $300.00!! After Ive read the over 400 complaints about this product, I really feel like I got screwed! My last Maytag EVER!

We purchased a washer and dryer, spent in the neighborhood of 1000.00 hard earned $$... extended warranty, the whole enchilada. Maytag. dependable, lonely repair man, ha.. that is just so much stuff. Well anyway it was a Centennial set. What junk. Never really worked that well to begin with. I trashed them both after exhausting all avenues to make it right. Well I got the hair to report the mess to consumer affairs and see if they are what they claim to be. This is more of a warning to all consumers.The stuff you consume today isnt worth the money you pay for it. The money isnt worth the time you spent to earn it. I am gonna try to find a old washer and rebuild it, and a dryer as well. Or just use solar. Best to keep the old stuff repaired and running. I dont know how many people I have spoken to about this problem. Our infrastructure is crumbling. A consumer based economy. Only there is not anyone to service the products we consume... pitiful. I guess my wife will be out back with a tub and washboard before it is all said and done... she will not like it, I guarantee that. I could not even begin to repair the washer. It was a computer operated board that did not work correctly from the beginning. The dude came out from the repair shop and fixed it while still under warranty. It died a slow painful death shortly after that. I disassembled it with a screwdriver and now have potatoes growing in the tub.The dryer has not met the same fate yet. It just sits there, anticipating the moment when I remove it and dissect it with a Sawzall. And I guarantee that day is coming. Do not buy anything from Maytag or its subsidiaries, think long term. We have become a bic lighter economy. I have been on the forefront of that movement. I did not realize it at the time. I do now. and for that I am sorry. I always expect something to work when I need it and if it doesnt, I try to repair it. Cannot fix this stuff now. The support we used to take for granted has been outsourced as well as the production of the product. Bob Dylan said it best in the song union sundown... Thank you and e pluribus unum.

I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is already in the junk yard, the drive system failed, the bearings failed and it began to leak. The dryer had a main control board failed, I was able to purchase a new one and replace it myself. The board was made in China, the machines were assembled in Mexico. I replaced the washer with a heavy duty Speed Queen washer made in the USA!

Maytag Bravos XL washer and dryer. Best washer and dryer I have ever owned. I have owned about every major brand and these are by far the best. My husband is a hog farmer and the washer does a great job. I will always purchase Maytag appliances.

We have had our washing machine for about 6 months, we got the F3 E6 error code. After doing some research, we found out that the control module was what we needed to replace. My husband and I called both Maytag and Lowe’s, (the store we purchased the washer from). We have been given the runaround. After talking with several managers in the Lowe’s warranty department, we were told that we had to contact Maytag directly about that particular problem. Okay, no big deal. We called and every single time we were put on hold for at least 30 minutes before we were hung up on. Not once did we even get to speak to a person. If we don’t get a response and our problem doesn’t get fixed, I will be going to the Better Business Bureau.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

I purchased my Bravo Maytag washer, dryer set May 31, 2015. I spent a little extra because they were suppose to be so reliable and last for MANY years. What a HUGE mistake! The washing machine is rusting. (A friend said, although Maytag’s big promotion was Made in America the inferior metal probably came from China). Buy cheap and to “hell” with the consumer! As many horrible reviews as I have read about the Bravo Series of washers and dryers I am shock there has not been a recall or better yet, a class action lawsuit! Rusting washing machine and have had to replace a part on my dryer...of course all cost came out of my pocket. I will NEVER buy anything Maytag as long as I live. I have told and will continue to tell my friends and family my nightmare Maytag story!!!

Water level is totally inaccurate, if you do get enough water in it, it will not spin clothes dry. This is the worst purchase I have bought in my entire life. This washing machine fails in every aspect period!! AND the matching dryer is a waste of space as well, clothes come out damp regardless of setting or time period. When I was younger, Maytag meant something, not anymore! I have searched to see if there are replacement sensors, or upgraded components to make these machines work properly, that I would even be willing to pay for myself and get them installed to make them functional, but NO they dont even offer that... we are just stuck with them. My water bill is higher and my electric bill is higher too! From these machines. I wouldnt even sell them used to another person. I wouldnt want them to inherit these problems, but as soon as I can save up enough money {being disabled} I will get these hauled off and buy a set of Speed Queen machines. My wife and I are so repeatedly disgusted!! I wish I had the receipt so I could post it for more proof.

The top of the range has blistered and has worn off. It cannot be cleaned. I spoke to a Maytag representative and was told to try and use magic eraser to clean around the burners. This did not work. The model number is mgr7775xs. Is there any solution to this problem. My range looks terrible.

Have had it for 2 years now and its leaked out the bottom since it was 6 mos. old. Now the ice maker has fried a motor and were having to repair it already. Cant believe we spent a small fortune on this fridge and are having constant problems with it.

This is my first convection oven. It is a double oven and I am hooked for life. I love the smooth top and use the convection daily. The only small issue I have is that the touch buttons on the range are on the harder side to push. But other than that, I have owned this for 5 years or more and would only get the same type again if I had too.

We bought our front load washer and dryer about 5 years ago and have had no problems with either. We also purchased a Maytag French door refrigerator 2 months ago to replace our Sears Elite brand when its compressor went out after 27 months (Ill never buy another Sears appliance).

I purchased a Maytag refrigerator about two years ago because of the Maytag quality hype. The ice maker has been leaking almost from day one and I need to clear out the ice from the bottom of the freezer every few weeks. Now the thing has quit cooling all together. I contacted the Maytag website and they recommended a local authorized repair firm. I took a day off work to meet the service provider. After checking the fridge they informed me that the problem was with the sealed system and that they could not work on it, and that I would need to contact Maytag to get a real Maytag repair person to come and fix the thing (right back where I started). They were however more than happy to charge me $70.00 for a service call. I tried the Maytag 1 800 number which was a nightmare and it finally hung up on me. I then went back to the website and managed to get a service appointment in two weeks (had to wait for a Saturday appointment because I cant afford to take another day off work). I just hope that this time it will actually be someone who can fix the thing and not charge me just to refer me back to Maytag again. I am not happy with the so called Maytag quality or their BS methods for providing service. Caveat Emptor if you are contemplating a Maytag appliance.

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

I purchased a Maytag dishwasher model number MDB7749SBM in May of 2013. In August the dishwasher control panel stuck on Rinse only cycle. It has been stuck on this cycle for a month. I contacted Maytag and they walked me through a reset. It has not worked. It looks to me as if the control panel has failed. This seems to be a common problem with the Maytag dishwashers. As soon as the warranty expires, so does the dishwasher. I purchased this dishwasher from Home Depot for over $600 thinking I was buying a quality product. My previous dishwasher was also a Maytag, even a lower end one that lasted almost 14 years! This one has not even lasted 14 months!!I was told by Maytag that I could purchase an extended warranty for $267.45 that would last a year. I believe, 4402 based on other reviews that I will be dumping more money into this one even after that. Very disappointed!! I will never buy another Maytag product again! I should have bought the Bosch. It was roughly the same price and high quality. I bought Maytag based on my previous experience. No More!!

I purchased my Maytag Bravos XL MCT because It could wash King size comforters/bed linen. I needed a machine that was large capacity. Also it was an HE washer that cut my water usage down quite a bit and reduced my water cost. Also this machine did a great job of cleaning my clothes and household items. The features were good. Variety of load type water temp if it was delicate, bedding, denim and more. I have had it for 5 years and so far no problems. It came with a 10 year warranty.

I bought a brand new refrigerator and about four months into using it, the freezer door began to become loose and opened by itself automatically. It also started to leak so I called the company continuously looking for a solution. However, they never resolved my problem. The company sent a technician. However he was unable to fix the problem. The technician said it was fine and did absolutely nothing. And now I am still waiting, but now your company says my warranty is up EVEN THOUGH I called much earlier and your company did NOTHING to help me. I need someone who can handle my problem. Ive been using your products for many years, and have always been satisfied by it. But this refrigerator has changed my perspective. I hope you give this a peace of mind and treat your other customers better.

Our experience with our Maytag refrigerator has been anything but good! It has the model # and serial # of the ones that have been recalled, only we have just found out about this. We bought this new at Sears. Soon after, it started having troubles with the freezer, would freeze up and the whole thing would stop working. Over the years, we have had repair after repair, money after money. Just for the record, my husband and I about every two weeks spend about one hour defrosting this monster! It looks nice on the outside.

We purchased this oven (MGR5775QDS ) along with a Refrigerator/Freezer, Dishwasher and Microwave on 2007 when we remodeled our kitchen. Since then the Refrigerator had to be serviced twice, the Dishwasher had a recall for fire safety - repaired, but I still have a scorched bottom tray, and the oven after self cleaning once has warped and the racks will not hold anything with any weight without collapsing. Maytag sent me new racks about a year ago, but that didnt help. I grill most of my meals or cook on the stovetop but on the rare occasion we try and use the oven it’s a nightmare. We lost a Thanksgiving Turkey and Easter Ham and recently a lasagna and a glass pan. Every time we have one of these events I search the internet in hopes that there has been some kind of recall on this model. It’s not safe. When the 20 lb turkey came crashing down, my wife was nearly burned by the juices that splattered and the house filled up with smoke. Happy Thanksgiving from Maytag - everyone go stand outside in the cold for 1/2 an hour while we clear out the smoke in the house. Recently when the rack collapsed and hot lasagna came crashing down, the glass/pyrex tray broke and left a huge bubbly mess in the bottom of the oven. Yay Maytag, thanks again - ruined a dinner, broke a dish and since we can’t use the self clean option, spent the rest of the evening scrubbing out the oven... and eating takeout food on Valentine’s Day. Sounds like the perfect Romantic evening right? I am so sickened with this company. We purchased all Maytag appliances because of their reputation. But now they dont even stand behind their products. What a shame.

The washer gets mildew all the time no matter how much I use the tablets and yes keep door open. It still has so much. I scrub it and it keeps growing. Sometimes my clothes come out ripped also which is another frustration. Please help these two issues.

The way the outlet line and pump are set up, the Maytag Bravos does not remove all water from the bottom leaving about 2-3 inches. Even following the monthly cleaning and care has not stopped the inside of the tub from producing MOLD. When I contact Maytag there was nothing they could do about this problem. At this point my washer is only a few years old. I attempted to clean it myself but the drum would not break free. My options are, deal with the smell of mold and mildew, Pay Maytag $250 to come out and clean it (this would need to be done every 1-2 years) or buy a new washer. NOTE: I paid about $550 for this one. I have run a few clean cycles with bleach, but I think at this point the mold has embedded itself into the plastic tub.

Maytag dryer MEDC215EW - This dryer does not dry the clothes without many wrinkles. Sheets just ball up with the inner sheet a mass of wrinkles. Small loads just flop from top to the bottom of the dryer, falling in clumps. I have gone back to having to ironing. Very disturbing!!! I would not recommend this dryer to anyone.

Purchased new Maytag MF 2558 VEM5 for over $1000 and have had nothing but problems. Water constantly leaking on floor, ruining kitchen wall trim. Now ice maker doesnt work. Bought in 2011 and started leaking after 2012 on out of Warranty. Now in 2014 ice maker stopped working. Bought at Home Depot who refused to fix. The worse fridge I have ever had.

Weve only had the machines for about a year, but so far they operate perfectly. However, the washing machine seems to take much longer to operate than my prior machine and is much noisier. But, the cleanliness of our clothes is great!

We updated our kitchen appliances in 2013 and purchased all from Home Depot. Purchased Maytag Refrigerator, free standing range and microwave. What a big mistake!!! Not one of them are worth what we paid for them. I just noticed that I was getting a (chemical) smell from inside our 6 year old 3 door model MFI2670XEM5 refrigerator. Well being I know what refrigerant smells like I have a leak in the interior of unit. This is my final issue with Maytag and their so called great built appliances, I have had nothing but troubles since about 2 years after we purchased it.I guess what really surprises me is that unit is built by Whirlpool and has their name all over unit and I always had good luck in the past with the brand. This is one of several issues including rust on freezer door, broken plastic drawer frames to French door hinges broken, ice maker door issues. What a waste of my money that I spent on these and now after 6 years need to buy all new. IT WILL NOT BE Maytag or Whirlpool!!!

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

The oven range (model number mgr8772wb) will not heat to proper temperature. It runs 35 degrees cold even after the built-in adjustment of 30 degrees. the repairman said it was just a cold-natured oven and we had to get used to it. So if a recipe calls for 400 degrees, you must preheat to 430 degrees. As much as this thing cost, it should cook properly. I must rethink Maytags reputation. I thought they were the best. Wrong.

I bought a Maytag dishwasher (model MDBH945AWB3) in March 27, 2010 to replace a Kitchen Aid dishwasher that was only six years old and no longer serviceable. After a little over a year, its dead. When I try to turn it on, nothing happens. If I press the delay button, the lights come on, but in about a minute, they go off.

I am online now because we have the same problem. Our refrigerator is less than 2 years old. Watched a video on YouTube how to fix problem and repairman said engineers who created design must have been on drugs. I think hes right. Very common problem. Have to call repairman!!

The washer does not get clothes clean at all even with the help of odor blaster, does not spin right, does not even out the clothes, walks while it is spinning. My towels do not smell good at all. The dryer gets too hot and the lint trap is always a mess even though I clean it after every use.

The new technology on the washers is useless and saves no energy or water. People figure out how to get more water in the tub and use that setting. There is not small or medium water fill anymore.

I bought a Maytag stainless steel refrigerator w/ freezer on the bottom. Since 6 months fridge being in my house I started to have problems, rust on the doors, water coming out of the bottom, freezer door got stuck w/ ice and couldnt be opened, butter, eggs, milk can be frozen one day and the next they have mold and bacteria because of the changes in the cooling system, among my problems. And what? Well yes thank you so much for the guarantee Maytag has in Puerto Rico, IT SUCKS! They been in my house more than 5 times and nobody really says whats wrong. They supposedly change the computer, still having problems, and this was done after more than three times visits from Maytag guarantee. Im still paying for the damn fridge and DO NOT HAVE A RELIABLE REFRIGERATOR. Im wasting too much food, Im obligated to buy food almost every day cause Im scare to give something that may be bad and my family will be food poisoned. Whos going to pay me or my family if something happens. Maytag is still running falsely commercial ads and somebody MUST STOP THEM. This appliances are not free or cheap. PLEASE help us because Ive learned that Im not the only one having problems in Puerto Rico w/ Maytag. Also I believe Maytag is using technicians not ruled by the government of Puerto Rico and thats why the service is horrible.

We bought a Maytag Dishwasher - Model #MDB4949SHW a year and a half ago at a Home Depot Location. We had previously had a Whirlpool dishwasher for 13 years of heavy use, with no issues or difficulties. At the time we purchased our dishwasher, there were various different brands on sale, including the one we purchased. The sales rep at Home Depot advised us that although we could get a similar dishwasher for the same price, that this particular model had a 10 year warranty. When I heard that, all I heard was 10 worry free years. MY MISTAKE. I could never have imagined that a company such as Whirlpool would advertise a warranty, that in the end is made up of nothing but false advertising.We ran a cycle during the Christmas holidays, and detected a funny smell of burnt rubber but didnt know what to make of it. I googled the issue and some people had had experiences with perhaps a plastic utensil or some other plastic, being burned by the heating element, so I figured that its what might have happened. I ran another cycle the next day, and the smell was much less prominent so I thought the problem had gone away. The next time we ran a cycle, the water didnt drain. We called in a repair person, and was shocked to learn that both the drain pump and main control board needed replacing.We got in touch with Whirlpool and low and behold, the only items they cover are nonsense items such as the racks, drum, tub...etc....in other words, the parts that are actually responsible for the running of the machine, are not covered, neither is LABOUR. Therefore, in my opinion, their warranty is trash and should not be relied upon under any circumstances. We purchased a new dishwasher just a year and a half ago, and are left with a heap of junk in our kitchen. Our options? Either spend $600.00 to $700.00 on repairs, possibly more, or buy a new dishwasher. When I asked if there was anything they could do to at least mitigate my damages, I was told....Sorry for your inconvenience...but do you have any other questions. I dont have any other questions...but I do have have a comment.... Make your products better....and dont print warranties that are utterly rubbish, false, and only serve to mislead the consumer. Needless to say, we will not be buying any more appliances from this company. Their one and only goal is profit for their shareholders with no regard whatsoever for the consumer. If I could give it ZERO stars, I most certainly would. :)

I have Control Panel issues with my Maytag Quiet Series 300 Dishwasher. I have saved myself hundreds of dollars! The problem occurs when oxidation or steam shorts out the ribbon on the control board. Simply shut off the power to your dishwasher. Open the 5 or 12 screws on the door. Open the black box where the Control Panel ribbon enters the Control Board, slide the white tension clasp away from ribbon and clean off ribbon using a paper towel. Re-insert ribbon and slide tensioner in place. Replace all parts and turn on power. Job done! I hope you have as much success as I did.

Control panel broken for a second time in 23 months: I purchased a Maytag dishwasher less than 2 years ago at Home Depot. 11 months later, the control panel went out. Specifically, the start/cancel buttons stopped working. A service tech called me under warranty; the control panel was shipped to me, and the tech fixed it. He also told me that they had had numerous problems with the control panels.13 months later, the control panel went out; specifically, the start/cancel buttons stopped working (sounds familiar). I can get nothing from Maytag, except a demand for service fees or sales pitches for extended warranties (at a price that was half of what the dishwasher cost new). They also offered me the free part as long as I pay the service call fees. I told them to just to ship me the part and that Id do it myself. Nope. I must pay the repairman. Now, theyll ship me the part if I pay for it, but they wont ship me the free part. It only comes with a service call.Maytag also told me that there were no reports of problems with the start/cancel button, an obvious lie with a quick internet search. The customer service rep sounded like she knew I was getting treated badly and kept using the word policy. Her supervisor was much more cocky and made sure I knew that I wasnt getting anything from her company.They make horrible products, attach what once was a good name, provide zero customer service, and lie to your customers. Great business practices. I will never purchase a Maytag product again.

Washer gets out off balance too easily. If I put in a couple of towels, it will almost invariably stop part way through the wash cycle. I was told you have a great washer! Its the last of the two-belt Maytags! My reaction: so what?

Like so many others, I now discover, we are having a ridiculously frustrating problem with our Maytag dishwasher, bought one and a half years ago. Last week, the control panel stopped working -- we press normal and a whole bunch of other lights come on; try to press other cleaning options and entirely different ones light up again. Sometimes we can get it, with luck, to quick wash or super clean and thus have our dishes cleaned (which the machine never did that effectively anyway); sometimes we cant. I havent called the company yet, but given what Ive read, Im unsure if it would do any good. Judging from all the similar comments, Maytag is clearly selling a radically inferior product and care nothing much about this. We will surely never, ever buy another one of their products.

I have nothing but great reviews for my Maytag experience... In approx 1975 I purchased a Maytag W&D, Model MAH4000 MDE4000, when their advertisement was portraying Maytag repairmen as the loneliest repairmen. Maytag was so dependable that the repairman was NOT needed...and it was true... That Maytag W&D set lasted til approx 1998 when it was upgraded to the Maytag Neptune MAH4000 series... Had a minor problem with mold in the washer, but Sears and Maytag replaced the seal and made another modification... We also dried the seal at the end of the washing day and left the door slightly ajar between uses... Have not again had that problem.I have since given the Neptune set to my daughter and the washer and dryer are still in operation, WORKING SUPERBLY I might add... So I am searching for a good quality Model MAH4000 and MDE4000 to replace my current much older, yet functional Whirlpool... It may need some repairs and about a year ago, I spent $173 to replace the Pump which was clogged by a sock inadvertently stuffed around the top of the drum when too many items were pushed in at one time. I prefer not to throw additional money at this machine! So, if you know of a Quality pre-owned Maytag Neptune washer and dryer in the Lexington KY area, please contact me...

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

I bought this washer (Maytag HE) almost a year ago, and if I could redo my choice, I would not choose this machine. There is no separate spin cycle. Often items are left with quite a bit of water in at the end of the wash cycle (often literally dripping as you transfer to the dryer), and you cant just rearrange them in the washer and then spin again. The only option on the washer is to both rinse and spin, which almost never helps get out more water. So you then have a heavy load in the dryer, much longer dryer time, and higher utility bills to get some loads dry, especially bath towels, sheets, jeans, etc. The washer is large capacity, but if you fill it more than 1/2 to 2/3 full (depending on the heaviness of your items) the spin cycle definitely will not get nearly enough water out of the clothes. The lid on the washer is SLOPED!The most ridiculous design I have ever seen for a washer, everything you set on top, even for a moment - laundry detergent, folded clothes, wet clothes - ends up on the floor. And the lack of agitator means at the end of the cycle, some loads that contain a sheet or any large flat item (tablecloth, etc.) the rest of the items are captured below the larger flat item that is over them like a mushroom cap. You cant tell how long the items have been like that in the washer, but its hard to imagine they are getting properly cleaned and rinsed. You absolutely cannot use powder stain removers, especially OxiClean, unless you are using the oxi cycle (much longer than regular cycle) because with any other cycle you will have white cloudy patches on all your clothes and items where the powder dissolved in the water but did not rinse out. You have to manually scrub them out, as putting these items through another wash cycle does not remove all the spots.

Received this Maytag dishwasher model MDW7749SBW1 as a gift from my son in June 2013 when my old dishwasher finally quit. January 2014, the soap/rinse aid dispenser did not work. Called Maytag and they sent repairman who replaced the part. Still did not work so repairman said another part was not communicating with the dispenser so he replaced that part. Worked fine. No charge since it was under warranty. Now its July 2014 and the touch panel doesnt work. Called for repair and was told since it is out of warranty, it will cost about $350 to repair. I called Maytag about this and said that I had a defective appliance. I was told that since I didnt buy the extended warranty, there was nothing they could do. I mentioned my last Maytag lasted 25 years and had only two minor repairs so I didnt see any reason to buy an extended warranty. I thought I was buying a good product. I was told shed register my complaint. Waiting for my repairman to come out tomorrow and see what he can do. I also have a Maytag stove. Wonder how long that will last?

I purchased my Maytag side by side Model No. MSB27C2XAM00 in August of 2013. Within a 2 Weeks the lettering was gone on the control panel for the ice and water dispenser. I contacted Maytag and they replaced it, but the next one did the same thing, and the next one! They replaced it three times and they have all done the same thing. Now they are refusing to do anything more because they say I must be using cleaner or something on the panel because I am the only one having an issue with this! I assure you I have not used any cleaner and there are only three people in my household so it doesnt even experience excessive usage! I know this problem isnt as extreme as some, but when you pay this much money for an appliance you would like to think it should last longer than this!

I bought a new Maytag dishwasher installed by East Town Appliance in Wautoma, Wisc. They installed it and ran a full wash cycle and it worked fine. After they were finished, I got all my glasses out and put in their dishwasher all excited to get them clean and sparkling. I started the dishwasher, put on a coat to check my birdfeeders on the deck where I was standing in front of the patio door. I heard water running suddenly. Turning around to see water gushing out of the bottom of the dishwasher. I called East Town back and had the installers return immediately. The pump was stuck open. I called Maytag about what happened and they said they wouldnt pay for the floor damage because it was already installed and to call my insurance company which I did. They went after Maytag and won but I had to pay $500 insurance deductible. I will NEVER buy anything by Maytag again.

I bought my Maytag Dishwasher (mdbh979aww3) about two years ago and just last week, the control buttons on the right stopped working. I see on this site that someone else had the same problem and explained that the wires got corroded, so now Im not sure I even want to replace the part when it only worked for 2 years. Now Im stuck buying a new dishwasher.

Our Maytag French Door with freezer on Bottom MFF2258VEB quit on us after three and a half years. Called local authorized Maytag dealer. They sent out a repair man. He said the main control board was bad! After much discussion we told him to replace it. After part and labor $261.00 it is running for now. Then called Maytag to see if they could reimburse us for the part $161.00. NO DICE! I have a kitchen full of Maytag products and a washer-dryer set but will not BUY ANY MORE Maytag products. Pass the word to boycott all MAYTAG PRODUCTS!

When I bought Maytag Neptune top-load washer, it lasted three months. I had to have the rockers replaced. Three months later, the lock switches went bad. Six months later, the main circuit board went out. Thank God it was under warranty. Ive had this ** washer four years and it broke down once again. I dont have any warranty and the money. They want to fix it. Im going to go out and buy something else. Piece of junk. It makes no sense. And when the first situation arose, I did ask if it had been recalled and of course, they said no.

I purchased this machine (Maytag washing machine model MVWB700VQ0) from Home Depot in December of 2008. When purchasing it I decided to spend a bit more money on the machine, thinking I would get a quality product. For the last two years and 5 months it has only been me and my wife in the house as the kids are in college. Hence, the washer has not been used as much as some would use it. Within the last two and one half weeks the machine started making a horrible growling noise (probably the tub bearing going bad) and then started to leak yesterday. I noticed this morning that there was a large puddle of bleach water coming from under the machine. I called Maytag, which is just a fancy name for Whirlpool, and they basically told me too bad. It is inconceivable that a machine that used to last 20-plus years barely lasted three with only two adults using it. When I owned my previous home in another town the house came with Whirlpool appliances which literally fell apart within 5 years. I wanted to stay away from Whirlpool; however, I did not know that Maytag was owned by Whirlpool. I have received no assistance from Maytag. I am absolutely disgusted with the fact that an American iconic company such as Maytag is producing such garbage. I am going to be forced to figure out and fix what is wrong with the machine myself. However, I do believe this subject should be looked into further and possibly a class action law suit against Maytag for bad customer service since there seems to be quite a few people with issues surrounding this machine.

Paint bubbling & peeling off appliance: I purchased new double convection oven from Lows (Maytag). One month after delivery, paint began to bubble and peel off. Maytag takes the position that as long as the oven functions properly, the paint is simply cosmetic and the warranty does not cover cosmetic problems. Maytags position is that even if all the paint peels off but the appliance still functions properly, too bad for you!

Maytag Bravo X-We bought this washing machine not even 4 years (February 2013) ago from Lowes. We had this issue before the warranty went up a couple of times and then it stopped and started working fine. We contacted Maytag before... But of course beings the issue resolved there was no way to send someone out here to troubleshoot the problem. Now it is doing it all the time. A few months ago it went out of warranty. We are having issues with it going into the spin cycle and it will stop there and it will not spin out my clothes and finish draining. Contacted them and they want to charge money for a service tech to come out just to look at it. Lord only knows how much it would cost to fix.

Update 3/7/2018. I have been without a working microwave since 1/23/2018. Technician sent from Maytag came out to repair it and said he needed to order a new board and door switches. These items were installed on 2/26/2018 but did not solve the issue. The technician said the microwave needed to be re-wired completely and would schedule for the microwave to be removed and brought to shop where it would be repaired. After I called Maytag and explained the situation they told me they would replace the microwave (with the same model.) I called today to get an update on when the new microwave would be installed and they said not for another 14-21 days!!! After expressing my displeasure at the whole situation I was told by the Maytag representative that I could choose any new microwave model (under $399) from the lines of Maytag, Whirlpool, Armana, or Kitchen Aid. It would take about 14 days for delivery and they would schedule the installation at no additional cost to me. So now I am researching microwaves again!!! Ill update this review once the new microwave is installed.

We purchased a Maytag 4000 series washer and dryer in October 2011, and within 5 months, the main bearing failed. The Maytag repair person told us it was an inherent issue and to make sure we use HE detergent (We always have.). Maytag advised parts were not available for 3 weeks, so no washer after 5 months of use. The bearing failed a second time after 11 months. Maytag refused to replace the washer and advised it was repairable condition. Now, we have the bearing fail a third time, and Maytag has advised that they would not repair the washer under the extended warranty program. They offered us 75% refund on the washer (So I guess they expect their products to only last 4 years.), which is simply unacceptable. We are now faced with purchasing a new washer, which will not match the dryer; or we have to purchase a washer and dryer of another brand. Maytag has provided pathetic customer support, and their response or lack thereof shows that they simply just dont care about their brand image or the customer.

My Maytag 2000 has ripped our clothes. This is my 1st front loading set. I looked on the internet and it seems that this is a known problem. Very upset that a brand that I had for 30 years and recommended to others as well has turned into a terrible company. Im a single mom and Im not in a position to replace a washer every year. I trusted Maytag! A recall and either replacement of the parts, or delivery of new part to fix the problem should have been put in place. I wrote to Maytag to see if they will do something to fix this problem.I have the set, washer shakes a lot, but works well. Washer also always has a lot of water left on the door seals folds, terrible design... I will post on other sites to warn other customers. This is not OK, my clothes are destroyed. See pictures. Clothes got trapped in a gap that exists in the perimeter of the opening, where it meets the door. Why is there a gap at all???

Maytag side-by-side fridge with water/ice dispenser (Model # MSD2572VEW00) was purchased in 2011. Mechanically, fridge is working, however, every piece of plastic inside the refrigerator section (the regular glass shelves with plastic rims, vegetable bins, and door ban shelves) are all cracking and falling apart. Additionally, the buttons on the ice/water dispenser fell off, exposing the actual buttons on the panel. All three of the regular sized shelves have severe cracks in the plastic that affect the sturdiness of the shelf. Both vegetable drawers are badly cracked, falling apart and one doesnt even stay secure on the track. Even all three of the door ban shelves are cracked with fractures along the sides and bottom. Weve resorted to putting clear packing tape just to hold the shelves together.We contacted Whirlpool, who owns Maytag and because our fridge is 4 years outside of the 1 year warranty, they could do nothing for us. In over 30 years of owning refrigerators, this is the first time Ive seen every shelf and bin crack the way this fridge has and in less than 5 years no less! Whirlpools solution to our issue was to send my call to their Parts Department. The total cost to replace all the cracked shelves, bin drawers plus the ice/water dispenser panel is $702.28. No thanks, thats as much as a new fridge. Whirlpool should be utterly ashamed of their total lack of Customer Satisfaction by distributing such a piece of junk. Who would have thought that an appliance costing a couple hundred dollars would be considered as disposable as an aluminum pan and in only 5 years! One thing is for sure, I will certainly think carefully again on ever buying another Whirlpool product again since they are so apt to take my money only for me to repurchase an expensive appliance again in less than 5 years.

My Maytag washing machine is nothing like the ones that my mom used to have. This thing is loud as it click, click clicks through cycles. Being a mechanical engineer, I assume that parts are taking a beating inside that machine to make all that noise. Then comes the wash time on this thing. With water level on auto sensing and one rinse, this machine takes over an hour to do a batch of wash. It literally stops dead for at least a full minute between each cycle then click, click, clicks its way to the next. It does not rinse very well as more often then not there is soap scum on the clothes when the washer finally stops. SPEND A FEW DOLLARS MORE AND BUY A DIFFERENT BRAND! Maytag is garbage!

We purchased the Bravos X washing machine on Feb. 9, 2012. I had a Maytag for 30 years before this one and did not have any problems. My model # is MVWX700X. I have given it sufficient time to get used to it. I have tried all cycles for my whites and am not satisfied. I use Clorox in the receptacle and I have only used Tide HE. I spot treat all of our underwear, which is changed every day, and it always comes out unacceptable. I am so disappointed since I was so fond of my old one and only thought I wanted another Maytag. At this point, I would never recommend this machine.

At two different times today I was left on hold for thirty minutes each. I was told the compressor only had a year warranty on it, cant do anything about it. I then went online to Maytag web page and it read only on compressor the warranty had ten years. I called them after a very long wait and was told that was just started with the ten year warranty. I have owned many different refrigerators never heard of compressor only lasting 5 years. The serviceman who came out to tell me compressor was bad said the name Maytag used to stand for something but now stands for junk. Worse customer service, worse product.

Dishwasher cleans well, but the control console has failed again & only responds to two functions. After replacing the console a couple of years ago with a new unit I thought it was done (it didnt get much use). Is there any recourse for this complaint? All I want is a new console panel. Maytags brand is apparently only good on the commercials. Very disappointing. Also, the top rack is very awkward & is only good for short glasses etc.

I purchased a Maytag dishwasher model MDB7749AWB2 in Dec. 2011 from Home Depot after a major flood destroyed my entire first floor of my house. I had replaced a previous dishwasher only a short time before the flood. This dishwasher is JUNK. I was lucky I bought a five year extended warranty on it which actually gave me 6 years. I needed it. Within a year the control panel went. Then water started spraying out the side of door. Then it sounded like it was crushing ice every time I ran it. Then the control panel went out again. Ice noise came back again. Control panel a 3rd time. It runs for hours as it is.Now the warranty is expired and last time I ran it the start light was blinking a few hours later. We were having high winds on and off so I thought maybe the power went on and off and that’s why it was blinking. Today I turned it on and after about 45 minutes I realized I didn’t hear it running anymore so I got up and looked and sure enough it wasn’t on. Normally the clean light is lit when done. I opened the dishwasher to see it filled with water still. I tried to hit cancel/drain but nothing works yet again. Wonderful news for a single mom that can’t afford to fix this over and over! Maytag is the worse company. Their dishwashers are horrible and they should be doing something about this as I’m not the only one that has had this issue. Home Depot was just as useless. Will NEVER buy again.

Purchased a Maytag refrigerator less than two years ago. Model M1txegmyb that was nothing special. Main purpose was to keep food cold/frozen. Now it makes noise and will not freeze anything. We called Maytag and they told us to take a hike or pay $469 for a new compressor on a fridge we spent $650 on. I would never buy their products again because the quality is so poor. Reading the other comments we have decided to throw the unit out at this point as we have pledged never to give Maytag another dollar.

Purchased a non agitator washer 1 year ago. Constant frustration with the sensing technology. Cannot select a water level or load size. The expectation is that the machine will do that automatically. The water dispenses through the soap container adding soap to dry clothes which then leave white marks on dark clothes. All of the selections for loads do not have a water level close to covering the clothes. The only way to achieve coverage is to reopen the lid multiple times to restart the sensing feature. Another option is to add wet clothes to increase the weight to “fool” the sensor. Some clothes have come out of the wash still dry in areas. Every load, no matter what size takes a full hour to complete! There is no quick load to be done! I have paused the cycle to leave the house and the water drains from the machine causing you to begin your 1 hour cycle again. Epic fail by the Engineers to provide a user friendly machine. This one, as time goes on, just becomes more frustrating and yes very noisy during the spin cycle.

We bought a Maytag Bravos three and a half years ago. We always tried to follow instructions for the machine. Only used he detergent, used the affresh, tried not to overload the machine etc. Had to call a repairman. Our washing machine started leaking water at the bottom. Hoping that it is only a three machine it would be fixable. Bad news the repairs would be over $600.00. It needs a new tub seal and bearings. For a THREE YEAR OLD washing machine! The repairman and I had quite a talk about appliances. He said they just dont make them to last anymore and the companies such as Whirlpool, Maytag, etc. do on purpose and they get away with it. Stay away from Maytag Bravos. It is a worthless piece of crap. It will not last long. Now we have a three year old washing machine that does NOT work right. Something has to be done in this country to come down hard on the companies that make appliances. I would NOT recommend this piece of crap of a washing machine.

I just found this website & do not have my model info with me. But we have bought 2 Maytag refrigerators since 2001. We still have the 2nd refrigerator but I want to replace it as soon as we can. They were different models but had/have the exact same problem. They freeze up into sheets of ice and then leak puddles of water on to the floor. Makes me mad when I see their ad about how great their product is - what a load of crap! My first refrigerator was a General Electric; it was still running after 19 years when I left the farm. I still have my 2nd General Electric refrigerator (18 years old) down in my family room - running like a top! NOT EVER GOING TO BUY MAYTAG AGAIN!

I purchased a Maytag Bravos line washer model # mvwx500xwo back in Oct. of 2010 thinking that it would be great to save money on the water bill. I first had issues with it putting holes in my clothes. I then found out if you do not zip up all zippers and button all buttons, the machine will rip them up due to the high speed spin cycles. Now, the washer will not fill with water or start the wash cycle. I mean really, its less than two years old and I have to shell two hundred plus dollars to fix a washer that only cost $500. I guess I know what brand not to shop for next.

There was a maytag dishwasher in the house we bought 11 yrs ago. The only problem we have had is a recall on the rinse aid dispenser which was replaced by a service man but never worked again. We are completely satisfied with the operation of the unit, our only disappointment is the wire racks. The original racks plastic coating broke at the end nubs and became rusty and swollen. We found someone selling a unit and we just took the racks and left the unit for him to resell rackless. Unfortunately not two yrs later the same thing has happened to those racks. Even tried these little plastic covers that are made specifically for this problem. They were virtually impossible to get on and didn’t last more than a few months.

First dishwasher was overheating fried control panel, turns out there was a recall. Got another Maytag at a discount. Thanks for nothing, little over a year, its fried too. Will never own another Maytag product again.

We purchased a Maytag Dryer with the lint vent on top on March 21, 2014 from ABC Warehouse in Ann Arbor, MI. Whoever engineered this does not dry clothes. Trust me, this will be the last Maytag I buy. There is lint seeping out of the top and when you clean it the lint gets all over the place therefore, my laundry room is always full of dust.

Our control panel just went out...purchased in November 2015. From reading reviews it appears our only option is to purchase a new control panel and hope for another two years. Ours (MDB7749SBM3 Dishwasher) was purchased from Sears and was not cheap. When is Maytag going to recall this panel? I read reviews that this problem goes back to 2011.

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

This machine that I bought 2 1/2 years ago is very loud. Sounds like a helicopter that is going to hit the house. Last week the machine did not empty and would not spin. What a mess. We had to take the clothes out and try to wring them out by hand. Then we had to scoop all the water out. Had to call a repairman to fix it. $187 which included two trips to the house and a new pump. The pump was $56. Just the last year my grandson came to live with us, but before that there were just two of us in the house to do laundry for.