Only 2 months after purchasing the Neptune Washer I required a service call as the washer was not draining. Technician replaced the pump and cleaned the drain filter. 4 months later the same issue happened. 3 months later the computer board was replaced and filter cleaned. Since purchasing this washer I have had to have 5 service calls to have it fixed. I called Maytag and they told me it is my fault the filter is clogged. Although the things in the filter are from my familys laundry the filter is located in the middle of the machine which requires the machine to be torn apart to clean the filter. This is a TERRIBLE design flaw which is NOT covered under the maintenance agreement as the service technician said this problem was caused by us. Maytag was the absolute worse to deal with as I have spoken to two levels of customer support managers and all of them said its my fault.

In the past 20 years, we purchased a washer, dryer, stove and dishwasher... all Maytag. The washer (purchased 20 years ago) is still functioning well! The other three appliances have all given us trouble and the dryer is no longer with us. Our stainless stove is LOVELY but thats about all its good for. Within 12 months, one of the burners burned out... just beyond its warranty. It has two ovens and 3 years after purchase, neither will hold a constant oven temp and both take an eternity to warm up... although the digital temp on the oven tells me its toasty warm. Recently, the dishwashers control panel wont set properly. An attempt to set it for a normal wash/dry cycle results in rinse only and a 2 hour delay. Make them like you used to, Maytag! Im no longer a customer!!!

Upon remodeling our kitchen about 4 years ago, we decided to put in Maytag appliances, one of which was the dishwasher . On Nov.29th, our granddaughters were playing with our dog when they ran through the kitchen and the dog started to yelp and went down and started to bleed. As she went past the washer her leg was sliced open by the bottom of the washer door. As it turns out, the bottom of the Maytag dishwasher doors has a sharp cut edge with no covers at all along the entire bottom of the door. We have also read about two children who have had the same thing happen to them. This is a very serious problem that needs to be addressed as soon as possible. The first surgery as of now has been $3,600.00 because of cut tendons. It would be totally irresponsible not to warn all consumers of this extremely serious hazard considering most families let their small children play in the kitchen

After first dishwasher was recalled, this one (installed less than 4 years ago - Oct. 2010) had the electrical panel burn out - two years ago. Now - for second time. LAST TIME BUYING A MAYTAG!

Had the new set for over a month now and are very impressed. If you actually know how to do laundry, and dont load it up to the top with greasy, dirt filled work clothes, etc. (like some **) you will have no problem lol. We have Absolutely nothing bad to say about Maytag products, and the new set is amazing!!!!

We purchased a Maytag refrigerator in 2009. The freezer is on the bottom. In the last 3 months weve had to defrost this frost-free refrigerator. The freezer frosts and the refrigerator went into the danger level for foods. A technician said there is a tube from the freezer to the refrigerator that gets blocked with ice and your food is spoiled in no time. I wish I would have read this website before I purchased a Maytag. Hopefully, this will help someone else. I thought that Maytag was a quality name. That was the good ole days and now Im living in the good ole days defrosting a frost-free refrigerator. Beware!

I just bought my Maytag Range model #MGR8700DS2 in August 2016. Bought Maytag because I always thought it was one of the best with the best warranty around. Now I am not so sure. After using it the first time, found that when you are baking anything in the oven the burner control knobs get very hot. That is because they designed the knob area to be right above where the heat vents out from the oven door. The knobs get so hot that you almost burn yourself if you touch them. This is a bad design in my opinion especially if you have any kids around. Even the sides of the oven get way too hot. This is also bad because of the tight spacing to your cabinets. I contacted Maytag about this and got a OH WELL kind of reply to my problem. You bought it and you are stuck with it. I would not recommend buying this model to anyone.

Always have bought Maytag. 16 years on both washer and dryer. The newer models, which I dont have, locks the top of the washer after it starts. I would hate that. I dont care if they are stackable but I would want full size. I dont think I would pay extra for a front loader, but the only front loading washer I have ever owned is small and at our camp.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

I have had and worked on many washing machines over the years. The worst design and complete failure of parts to easily align in Maytag front end washers is nothing short of staggering. Creating a tension wire to wrap a rubber seal that requires Hercules to install and easily tears the rubber is beyond ridiculous. Avoid front end Maytag washing machines like the plague since they may cause it given the mold and growth from excessive moisture when the seals tear.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

My husband and I purchased the Maytag dishwasher model #MDB7609AWW2 in December 2010. July 2012, the control panel would not operate. I called Sears to schedule a repair appointment. (I did not have an extended warranty.) After reading review after review of complaints about Maytag and control panel issues and learning it is a very costly repair, I called Whirlpool which now owns Maytag. (Be advised, Maytag is not the quality product it once was). Reviews also indicate that the replaced control panels are failing within 6 months to a year and a half. After talking to a person in the Maytag/Whirlpool service department, he suggested some things to do: unplug power, unlock control panel, etc. He determined it was most likely the control panel that needed to be replaced. I asked how long a new panel would last informing him of the complaints Id read. All he would tell me was that I had the option to buy an extended warranty. We have decided not repair the dishwasher and will replace it with a non-Maytag and non-Whirlpool brand. I will never buy Maytag or any products made by Whirlpool again. For a major component of the dishwasher to last only a year and a half is unconscionable.

I Hate this machine. It does an inferior job and I wish I never bought it. Our Bravos XL washer was purchased in spring. It left white residue constantly on my clothes. Even WORSE, the machine wrinkled the permanent press so the clothes had to be ironed before wearing. (I rarely had this with my last washer). I used the machine settings correctly and I called the company and basically...was told, Youre out of luck. I hoped that it would improve but No Way! Dont purchase this machine, dont waste your $$$.

We purchased a Maytag Bravos X washer 2 years ago. Theres not enough water in there, and the clothes get so tangled that Ive had holes in them. Ive had technicians come out several times and they just say that its the water saving feature of the washer. I put it on the wrinkle control setting and the clothes come out ridiculously wrinkled. All of these problems are due to the water saving feature. I absolutely hate this washer and would never recommend it. I want my old washer back with the agitator and enough water in there to actually wash clothes.

We had a three-year warranty which expired. We used a repair once for a rusting Clorox basin. Now, the tub swings wildly on every wash and will not complete because we get the UL warning. Weve tried making sure the washer was balanced but confirming that nothing helped. Most expensive washing machine ever and shortest life apparently.

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

Maytag dishwasher from Home Depot, model MDB7749SBM1. Bought it last May from Home Depot - in a little more than one year it has already needed 2 repairs to the control panel. We are having a lot of problems finding someone to come and repair it. We want our money back. This is a piece of junk!

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

Like so many other people reviewing Maytag refrigerators with bottom freezers, I am dealing with water on the floor. At 64+, I am not eager to tackle the problem as a DIY project. Once of defrosting and cleaning up was enough. I love the looks of my 2 yr old $2000 4 door fridge/freezer but hate the issues. I guess Maytag is going to ignore all of us. When someone finds a reliable company, sing it from the rooftops.

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

MBL2258XES1 - Like most of the other reviewers, we have a Maytag refrigerator just 3 years old with a lower freezer that leaks water onto the floor -- and has been doing it for the last two years. We have to take the freezer apart (NOT easy), defrost it, take the back panel off, and clear the drain tube. Obviously a defective design! Cant believe Maytag hasnt done something about this!

I purchased Maytag dishwasher (model # MDBH979AWW3) in June of 2010. Trouble started on washer after 18 months. Touch pad buttons dont all seem to be working. Occasionally gets to run after slamming door multiple times, but dispenser doesnt function properly. After trying to diagnose myself with door switches, connectors, etc., I caved in and called service. Service quoted $470 parts and labor to fix the problems, including control touch panel, dispenser, and control board (seems common from what I read here). Wish I had seen this string of posts before I called Maytag/Whirlpool customer service to see if they would help before I did any repairs. The responses I got from the service rep were rigid and scripted. Only time she varied from the script was to explain that modern high-efficiency appliances dont tend to last as long as ones 20 years ago. 18 months? Really? I might buy that if it was a mechanical durability design issue. Supervisors responses were also scripted, pointing back to the 12-month warranty. She said she did a warranty search on my model and that there was no warranty concern for this problem (really?). If there was, she might be able to help me. I guess there is no warranty history because most failures are between 12-24 months and the consumer has to pay for replacement outside of warranty. No semblance of customer service or customer care, just repeating what is on their website. Response was: I am sorry you are dissatisfied with the product and my response, but there is nothing I am authorized do. Sent an email to Maytag customer service regarding the problem and customer service interaction. They called back saying they stand by the original customer reps response, but offered to have someone else come out to give a second opinion on the problem. From what I read here, that doesnt seem necessary. Wish Maytag/Whirlpool would at least acknowledge that there is a problem, even the auto industry seems to have figured out a way to equip the service industry with known recurring problem history (TSB) and offer token help to keep customer loyalty. Apparently another quality organization fallen victim to short-sighted methods of maintaining shareholder value.

Horrible machine. Uses too little water, cycles are too long. No matter what the size of the load, it takes an hour. Just after 3 years the bearing went out on the machine. Cost for repair will be $250. Thats not even an electronic problem which Im sure would be next. NO THANKS. Im getting a new machine and it wont be a Maytag.

Maytag model mfd2561hes French door stainless steel purchased in June 2005 has been the worst appliance purchase ever. After 1 year warranty expired, icemaker and water dispenser stopped working. Was told by repairman to thaw the tube for water dispensing with a hair dryer. Are you kidding me? Why should I have to pull a huge refrigerator out from wall and put the hair dryer to it to thaw out the water line when I need water? What is the convenience to that? Cant buy fresh vegetables as it will freeze before I can use it. This is the worst appliance ever. Dont buy Maytag products. Maytag doesnt back products like the old days when they would last 20 + years. Cant last even a year anymore. Sad!

I bought a Maytag Dryer from Lowes in December of 2013. I paid 600.00 for this dryer which I thought was going to last for quite awhile. It stopped working in January of 2016. (2 years old). I had a repairman come out and he said the motor had burned out and he wanted 300.00 to fix it. I called Lowes and asked if I should expect the motor to burn out in 2 years; they said of course not - call Maytag. That proved to be a complete waste of time. They would do nothing. They simply said that there was not a recall on that machine and they were not technicians. However they would be glad to send someone for 125.00 dollars to look at it, then the parts and labor would be more. I have never had a dryer burn out in 2 years - not even when I was raising children and using a dryer daily. This Maytag clothes dryer isnt even used every week and when it is used, there are a few small loads. I am appalled and disappointed in Maytag and the poor quality of this appliance as well as their horrible customer service.

I purchased a Maytag Dishwasher Model MDB7749SBM3 in January of 2014. I have had issues with the control board for the past month: lights come up at random; it takes 3 to 10 trials to get it to start and now it is dead. After reading many reviews on this site, I now understand what the problem is. I called Maytag customer service and they wanted to schedule a service call at $98 just for the diagnostic. I asked the Maytag associate whether the control panel issue was a common problem and she said she would research that but did not give me an answer. I am totally disgusted by this company!!! I would be happy to join a class action suit.

My husband and I bought a Maytag dishwasher, Stove and Fridge. We were very reluctant because at our prior home we had Maytag appliances and they kept going out. Against our better judgement when we moved into our new home we decided to go with Maytag once again. First the dishwasher front panel stopped working. We had it replaced and it cost over 250.00 with replacement part and labor. Not a week later went by when our Fridge went out, that cost us another 300.00 plus to fix. Keep in mind we had only had these appliances for about 14 months. Less than a year of replacing the dishwasher panel it has gone out again. This is very frustrating and expensive. I dont usually write comments, but felt the public needed to know that Maytag has poorly made appliances. I recommend you spend the extra couple of hundred bucks and buy the better brands and warranties. Thank you.

Purchased a Maytag dishwasher in 2009 then had it repaired for a leak in 2010 (just past the 12-month warranty); next another leak in Nov 2013 so purchased another Maytag as repair appliance company said it wasnt worth fixing. Now in Feb 2015 it is leaking Again! So 2 dishwashers and 1 repair in 5 years! Both were purchased from Home Depot. I will Never buy a Maytag product again.

In May of 2009, my husband and I bought a new Maytag refrigerator side-by-side, model MSD-2572VEW. The day we bought it, pieces started breaking. The shelves started cracking, and now they are completely falling apart. There are also cracks in the inside walls of the refrigerator. Every single door shelf, inside shelf and wall is falling apart. I have fixed the ice-maker myself several times. I am now going to design and build some new shelves so that we can get as much use out if it as possible before it is unusable. I am angry that a company can make such a horrible product and not have to take responsibility. If my employer ever provided a client anything but the best, we would all be out a job.

We bought a new Maytag electric range from a local dealer three years ago. The oven element quit working, which shorted out the motherboard that controls the entire range. The cost of repair was $500 for the element, motherboard and installation. We have owned other brands that lasted 20 years and worked fine with no repairs. My folks have used Maytag for over 50 years with no problems. Who and where is this junk manufactured now? China? I will never buy another Maytag product!

I have done absolutely nothing to this dryer except keep the lint screen clean. Have had it for 15 years. Keeps on tickin. It is used daily. Sometimes 3-4 times a day. The outside looks rough. But who cares. I bought a new lg washer with great looks and had it just a year and 2 weeks. Had to spend another $200 on it. Still doesnt work right. Im Maytag all the way!!! It is a simple dryer. But it is a workhorse. It was a gift from my mother and have so much appreciated it. It has been an amazing piece of equipment. From now on I will only look for the maytag brand for whatever appliance I purchase.

I have called this company several times. Most of the time, they tell you that you need to call another department...which means you spend even more time on hold. This washing machine is only 3 years old. I will never buy another Maytag/Whirlpool product again!

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

Maytag Dishwasher MDB8959AWS6, S#F15006566 purchased 12/28/2011. Here is a record of the product repairs done by All Tech Appliance Service in Portland. 1/12/2014 - Thermal Fuse and Control Board. 10/15/2015 - Thermal Fuse. 9/2/2015 - Thermal Fuse. 12/5/2015 - Unit stopped working again, strong electrical smell, probably Thermal Fuse again. This dishwasher product has a design defect. It should be recalled.

This review is for a Maytag Gemini MGT8775XW 30 Freestanding Double-Oven Gas Range w/ 5 Burners. I cannot believe the amount of problems I have had from this $2000+ range. Within just a few weeks of getting it, the paint started scratching off the surfaces nearest the heat. Then, the plastic cover over the digital display and controls bubbled up due to the heat of the broiler being in use. They designed it so that the heat escapes from the oven right in front of the control panel, so when you want to adjust temperatures on the control panel, you chance getting burnt from the hot air every time.The very worst design are the manual knobs for the burners on the front. They are at an angle, and if you look at the oven straight on, you see they are higher than the burner surface. A hot pan that overhangs the burner cooks the knobs. The plastic interior of the knob lacks any kind of heat resistance and actually starts to turn soft, keeping you from being able to turn off the burner at all!Most dangerous of all, the knobs are frighteningly easy to bump, pouring gas into your house. We have had this problem multiple times. Today, my dog must have wanted to investigate the top of the stove, because when I came home, the burner was on, had burnt through a pot on the stove, and was just at the ignition point for an item sitting next to the stove. If I had come home 15 minutes later, my house would be in flames right now. I am having to air out my home as I type this. I am DONE with this dangerous oven and will be shopping for a new one, and it certainly wont be Maytag.

I purchased Model #MGR7661XB (Gas Cooktop and Oven) in November 2009. From the very beginning, we realized it was a mistake and looking back, we should have sent it back.The finish, both on the stove as well as the burner racks (the removable grate that the pan sits on when cooking) has some sort of coating that instead of repelling grease and food seems instead to actually attract it. Any hot liquid or grease actually seems to melt into the finish and becomes impossible to remove. Essentially, our stove was ruined within the first week. We have even tried putting a scouring pad on a wooden spoon and scrub with as much force as we can muster - to no effect. Short of using a putty knife, and completely destroying the finish, I cant think of any way to resolve it.As for Self-Cleaning ... yeah, right. Use for entertainment purposes only. It doesnt clean at all.The latest issue is now the oven lights about 20% of the time. The broiler still works and we have discovered that we can trick the stove by allowing the broiler to heat up the stove to about 200 degrees first - then, when the oven is already hot, the oven part will ignite.Speaking of igniting ... from the beginning, this stove has the loudest ignition system I have ever heard. You can hear it ignite click/pop from two rooms away and the oven cycles on/off every 10 min. or so. It is very annoying.All I can say is, never again will I buy another Maytag. This was supposed to be the upgraded sealed burner model (which also is impossible to clean). This stove is only 4 years old but it was a mistake from the beginning. Like I said, I should have returned it after the first week.

We have had this refrigerator, model MFI2665XEM7, less than two years. The ice maker stopped working and we had it replaced at least 6 times in a two month period. We had a solid ice sheet in the bottom of the freezer drawer and it leaks water on the floor constantly! Even today... after another ice maker replacement, we have no ice! I never wanted a Maytag, but finances and the small space we had gave us little choice. I am not sure what our next move is. I will NEVER buy a Maytag product again! I should have google this sooner and we could have saved the poor repairman all of those trips!

All of my brand new white wash cloths have black stains on them. They look like mechanics use them to check the oil. And, my white denim capri pants have weird stains on them. This washing machine is a joke. It may be water efficient, but sacrifices cleanliness and stain removal. Maytag should recall this ** Queen.

Not only does dryer come with missing parts and are told by Maytag 1 to 2 weeks for delivery or drive 25 miles to pick up one. You do not qualify for rebate even though you do not receive washer and dryer for 5 days after rebate starts. Should have kept my old GE was faster and got clothes cleaner. Was looking at a Maytag refrigerator not anymore with their service.

I purchased a Maytag range with self-clean oven. Manual says to put 2 cups of water to self-clean and no cleaning is done. I called Maytag and they said it is environmentally friendly and the rest of baking stains I have to scrub myself. This is totally unacceptable. I also cannot clean with easy off, it will damage the inside of the oven according to Maytag customer service. I do a lot of baking. What am I supposed to do now, live and cook with a dirty oven! Ugh!

Do NOT buy a Magtag washer. I purchased a brand new washer from Lowes in 2017. The washer gets stuck in the wash cycle. When I called Lowes, they said to call Maytag, who sent a service person out. The service person recalibrated the machine never ran a cycle and left. We had to call two more times after this for the same reason with the same result where the serviceman left without running a cycle. This was all while the product was under warranty. Since I had three service calls, I called Maytag frustrated that this kept happening to a new product. I was told there was nothing they could do, but if it happens again to have the service guy come back out. When the warranty runs out, I will have to pay for the service tech. Unbelievable. Save your time, money and frustration and buy a Whirlpool! I dont know how Maytag gets away with selling defective products.

I bought a Maytag MDB8959SBS2 December 2013 with several major appliances for our new home while they were all deeply discounted and bundled with cabinets etc from Lowes. Moved in June 2014. Said dishwasher crapped out last month (May 2015). Buttons all fouled up, push normal and 6 other lights come on. Tried different resets, reboots, power down all no good. I ordered parts to repair, control board, control box, no luck. No warranty because purchase date was December 2013. This thing didnt last 11 months of use, and its just my wife and I running maybe 2 loads per week. I will certainly do more research and buy a foreign make/model or at least one not made by Maytag or affiliated brand. Unfortunately this supposed Made in the USA sticker sure doesnt stand for quality with this company.

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.

This washer is awful. We had repair guy out within year one 3 times. Changed the door gasket because it was a known problem. That did not fix problems. We have to drain and clean out hard to reach filter monthly, socks get caught in drain filter constantly. Horrible, horrible, horrible. Hate it.

The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

Warranty dept. will not help you! I have been told by technicians sent to service my refrigerator after it spoiled food multiple times from not staying cold. The technician flat out told me that this refrigerator cannot be fixed but they are not allowed to say that it cannot be fixed. They will not return your calls and are just flat out rude. After asking to escalate a call, the rep said the manager will call me right back in a few minutes. Hours went by and I called again five minutes before they closed to speak to someone in management at that moment. This manager told me with no hesitation that they dont always believe what their technicians say because they send out techs that are good, okay, and not good. My first question is why is Maytag confident in the people they are sending to my house time and time again that stay for three hours?! She began to get rude and disrespectful and said, Well, if you had cancer, you wouldnt believe the first thing they say... I am in awe of these remarks. How do you compare a refrigerator to cancer?! I asked for a business address and stated that I would like the address to file with the Better Business Bureau and she told me that they have all the info I need. She refused to let me speak to anyone else. This situation is uncalled for when I have the technician telling me, This refrigerator is not repairable but they wont allow me to say that and Maytag will not make this an easy process for you. Unbelievable!

Same issues as many others here, had to replace the main control board a couple of months after the warranty period was up. Funny thing is though, I brought the old board into my local electronic repair shop thinking it might be worth getting it fixed in order to have a spare on hand in case the new one was also short lived... He told me he examined the board and there was nothing physically wrong... The problem he said was in the programming or firmware. Unfortunately, he said Maytag does not offer an update and there is no way to clone the newer version from my new board onto the old one so it was garbage. Seriously Maytag? Hundreds of dollars later in parts and melted groceries all because you wont issue a firmware update? Also have water leaking out of the bottom of the fridge late at night so Im never awake to troubleshoot it. Considering how sporadic it seems to be, Im guessing it must have something to do with the defrost cycle... Have to figure it out though as its starting to cause damage to the floor and leaking down to the basement :( Never again Maytag.

Maytag dishwasher, MDB4651AWW was purchased on 15/02/2010. Touch panel was replaced under warranty on 16/08/2010. Touch panel became defective on 04/07/2012. It was $103 for the service call: panel was not replaced (too costly, > $200). My 2-year old dishwasher is now useless. The touch panel on this model has failed twice in two years and is obviously a design failure. I would ask for a free replacement panel.

Maytag top load 300 series washer - This is the worst washer I have owned! It does not wash items- especially sheets - without getting totally tangled up and twisted! I wish I had my old one back that lasted 20+ years. I will NEVER buy another.

I purchased my Bravos washer and dryer in Sept. 2010. What a mistake! The dryer is okay but the washer is a nightmare! The repairman and I are on a first name basis. The last time he was here, he showed me how to recalibrate my washing machine. It stops working in the wash cycle, fills with water and then sits there. I have to manually drain it and start over. Then it gets confused and fills with water when it is supposed to be spinning and draining (consequently draining my well). I shouldnt have to recalibrate anything in life, much less, a brand new washing machine.

We purchased our Maytag gas range in 2015. Within 6 months we noticed the clear coat and paint was defective, we called Sears, they allowed us another range top and replaced it but told us our warranty was up in a month and they would not replace another. The stove always looks dirty because the clear coat and paint have bubbled up and it is clearly a 100% manufacturing defect that should be recalled.

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

This is the worse washer... As many other have complained I have the same problems. This washer it will not fill with water ever. It doesn’t rinse clothes or clean them as I’m use to the old washers doing. From day one I noticed the water does not fill in the tub and wondered how can the clothes be getting cleaned properly. Getting a F51 code and after going on YouTube and checking for problems it seems to say the same code after it works for a bit. This is the worse appliance I have ever purchased. I am so frustrated and will never purchase a Maytag anything again. Never did in the past up to this one and never will after this one.

Bought this Maytag Bravo washer in 2013 expecting long service life like I had with my previous machine. After 2 years spin cycle noise got progressively worse. Until now it roars loudly and keeps stopping in the spin cycle for rebalancing. Called Maytag. Experience was as described as others have reported with them and their repair service. Absolutely no help unless I spend another $310 for extended warranty to cover the $380 part (tub and bearing - 1 unit - cant get only the bearing). Paid $800 for the washer now more for the repair wanted. $1100-$1200 for a machine that will need repair again in a couple of years? Dont think so. This machine is only good for a boat anchor. Going out today to buy a replacement for $400 and it wont be a Maytag or its affiliates brand. Feel like a class action suit would be good for Maytag to wake up to.

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

Purchased my appliance at Lowes in 2012. I have had at least 8 service calls, the unit has NEVER worked as designed. Water leaks inside and out. The ice maker door heater had to be replaced. Fan Motors have gone out on it, broken water tubes. The temperature wont stay consistent, it freezes my refrigerator items, ruptures beverage bottles and cans. This once quiet unit is 3 times as loud than when I bought it. I am so frustrated!!!What a value $2,000 for the appliance, $700 out of pocket for repairs to date, $$ in lost food items, $$ in my time to clean the mildew, water, exploded beverages, cant put a $$ on the embarrassment when family/friends use. What is the potential danger to myself and family when the mildew is in the unit and water leaks into open refrigerator items? Next scheduled repair from my factory authorized repair technician? 10/29/2013.

Purchased a new top loading HE washer in 9/2012. This machine gets very little use - approximately 10-12 loads a month. It is now broken awaiting parts which will cost about $200. Of course the warranty is only good for 12 months There is no excuse for a washer this new breaking and costing this much to repair. What a piece of junk! Avoid all Maytag products.

Purchased a supposedly top-of-the-line Maytag washer and dryer (9000 Series with Steam and MCT-Maytag Commercial Technology; Washer MHWE900VJ). Just under five years of use and the repairman quotes me just over $1000 parts and labor with the overwhelming majority of that quote being parts. No wonder the Maytag repairman is the loneliest guy in town - its not worth fixing your not-yet-5-year-old machine. It kills me that companies are allowed to advertise and promote the quality and reliability of their products and less than 5 years later, the machine is going to the dump, after having paid a premium for quality. This technology was supposedly comparable to what is used in a commercial setting - not very believable in my opinion. No more Maytag or Whirlpool for me.

Bought a French door Maytag with freezer on the bottom. Ice build up on the bottom of the freezer and it has ruined my floor. We are replacing the floor in the kitchen. It is only a few years old. They have horrible customer service and will not replace anything.

When we sold our home (to buy a new one), it had a really nice matching set Kenmore front load washer and dryer, which worked fantastic!!! We gave the Kenmore set to someone, since the new home had a brand new Maytag Bravo XL, and Im regretting it... Our clothes are always full of lint, it does not remove any dirt and God forbid you spill something on your clothes, our white clothes are now yellow, and his work clothes (dress, shirts and pants) are ruined due to the harsh rubbing from the lack of water... I wish I would of done an Internet search on Maytags Bravo XL before getting rid of our old washer... BUYER BEWARE is all I can say!!!

We have owned the dryer (Maytag Bravos) since Dec. 2010 and are now on our 4th service call. Upon the second delivery of the part that was ordered last week - we will be on the 5th service call. I finally asked Maytag if I could get a trade in since this dryer is obviously crap. They said they could only handle the problem at hand, which is the same problem over and over and over. The flywheel was left off all together. The pulley belt for the dryer pops off about every 4 to 6 months. Ridiculous. Its a crap dryer, dont buy one!

I purchased a Bravo Washer and Dryer from Home Depot. The Maytag Bravo washer and dryer we purchased from Home Depot did not work from the beginning. Before I called Maytag, I tried for several months to redo the way I was loading the washer and dryer.I tried several different settings however, the clothing keeps coming out smelling like it is still worn. Spots are in the clothing that normally comes out with a washing (with my prior washer). The clothing just does not get cleaned and it gets so tangled that it has ruined some of my clothing. There is clumping of the detergent, even though not a lot has been used.I had the repair company come out three times for both the washer and the dryer. They have checked and no errors codes where found. One gentleman told me again to redo the way I load the washer and the dryer. I have done it so many times, but I tried again and even purchased little dryer balls. It made no difference.I called Maytag again and was told they would have to have another company come in and do a second opinion. The person came and said that he agreed that the washer should be able to wash and the dryer should be working correctly. He recommended that a possible problem with the motherboard for the dryer (which was a possible problem mentioned by visit #2) could be handled, but he had to have it approved. He would check with the company and get back to me. I received a call the next day and a message was left telling me there is nothing he can do with the washer. He was told by Maytag/Whirlpool that I should only fill the tub lightly and not pack it down (I told everyone how I load and I never pack my clothing down). The washer should, when loaded with wet clothing, be only 1/3 to full otherwise it decreases the wash ability dramatically.The problem of the siphoning action for the softener section of the washer should be handled by running boiling water through the tube to loosen up the wax portion of the softener. The possible correction for the dryer exchanging the motherboard (it could be set incorrectly) was turned down by saying that the dryer is running to Maytag/Whirlpool’s satisfaction and nothing else would be done, since there are no error codes for both washer and dryer.My towels have a mildew odor to them when they are used. They have to be washed twice and run through the dryer a long time before I can put them away. I purchased a high capacity washer and dryer and I am told now not to fill it more then 1/2 full. That is not what I was told by the person selling it. Otherwise, I would not have purchased this set at all.

While washing clothes in my Maytag front load washer, I noticed that there was water leaking from the front left corner from the bottom. I have owned the washer for only 2 years, and Maytag manufacturer (Whirlpool) told me that it was going to initially cost $80.00 for a service call and then more money to fix the leak. WOW. Also the wood floors that are underneath the washer and dryer, is starting to warp from the leaking washer. I would recommend DO NOT BUY A MAYTAG APPLIANCE. The warranty is basically worthless along with the washer.

We bought what was supposed to be the top of the line Maytag dishwasher as part of a kitchen remodel in 2011. Well tonight it has quit working for the 3rd time! I think this is the last straw for us! Tired of spending all this money having it fixed. We also bought a Maytag microwave at the same time that has been nothing but trouble from day 1, but not as bad as the dishwasher. I can promise you we will never buy another Maytag product ever. Heck at this point, I would not accept a free Maytag machine of any kind! Stay away from Maytag!! Just to be more specific, the first time the dishwasher quit it was the board and cost us half as much as the dishwasher. I see lots of mentions of boards going out early.

2 major repairs in 8 years, ridiculous! We purchased a washer and electric dryer pair in Feb. 2012, had a repair for the control board (CPU) 4+ years under extended warranty, had another in 2018 for the same thing. I was told power surges could cause it, however I have a WHOLE HOUSE SURGE SUPPRESSOR ON THE INCOMING 200 AMP SERVICE AND KNOW THATS NOT THE PROBLEM!!! Had the same CPU go out again in Nov. 2020 so, rather than pay $370 for the part plus labor, we bought a top loading GE with an extended warranty and factory 10 years on the motor. We will never buy another Maytag product again. We were told that we shouldnt expect to get more than 6-7 years from a washer now, ridiculous. Manufacturers are outsourcing electronic boards overseas to maximize profit and could care less about quality control!!! Junk!!!

Dryer doesn’t wash all the clothes and the dryer doesn’t dry anything correctly. All, regardless of materials or size of load, comes out damp. Repairman’s excuse was that it’s a learning curve(?) and our dryer vent was the cause (which it wasn’t as we had it checked out and there was nothing in it) and that was it. Very disappointed in the washer and dryer and now the company where we bought them as it seems that we’re stuck with over $2K worth of equipment that doesn’t wash or dry well. We’re awaiting to speak with manager for a replacement of anything not Maytag. Not holding our breath and definitely not a happy customer.

I bought a washer and dryer a few months ago from Home Depot Maytag. My clothes do not come out wrinkle-free. They are very wrinkled, to the point where I have to iron the perma press. The dryer I just got rid of was 30 years old, and always got the wrinkles out of the clothes. So I am very disappointed in the way yours works. I dont know what you can do, but this is not good. Thank you.

WARNING FIRE/HEALTH HAZARD - BRAVOS MVWX500XW1. Purchased it new 2011. Never cleaned well. Some clothes came out with dry spots, darks had soap scum/lint spots over them. On several occasions, clothes were not wrung out properly. BUT when I went to do a load of laundry recently, I heard a loud POP and almost instantly my entire basement filled with an acrid, dense grey smoke coming from under the machine. I am concerned toxic chemicals were released. People still smell the odor in the house. Need to get in touch with company again after the weekend to see what they will suggest.

The Maytag Neptune TL washing machine has always been extremely loud! It smells awful and now our clothes too! I have found mold in the washer and cannot get it all out even with bleach. My children are extremely allergic to mold and they have had problems because of this. I am very disappointed in this washer and find it sad that no kind of action has taken place to help people who have bought them.

Before you purchase a Maytag washing machine...from anywhere (I got mine at Home Depot), think again. This machine doesnt wash clothes, it doesnt rinse clothing. What it does is takes forever to fill up the tub then it doesnt even come close to filling it to where all the clothing is covered for rinsing or washing, then it just stops and sits there for a few minutes (??) and then it proceeds to empty the tub and youre supposed to feel like your clothes were cleaned.Not in a million years will your clothing get cleaned in a Maytag washing machine. Youve been warned...dont waste your money. Go to a used appliance shop, but the best one they have that does NOT have the Govt. regs built into it, and be happy you saved as much money and did NOT have to go through all the frustration and hassle everyone else has that bought a new Maytag washing machine.

Our Maytag French Door with freezer on Bottom MFF2258VEB quit on us after three and a half years. Called local authorized Maytag dealer. They sent out a repair man. He said the main control board was bad! After much discussion we told him to replace it. After part and labor $261.00 it is running for now. Then called Maytag to see if they could reimburse us for the part $161.00. NO DICE! I have a kitchen full of Maytag products and a washer-dryer set but will not BUY ANY MORE Maytag products. Pass the word to boycott all MAYTAG PRODUCTS!

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

Fifteen months after purchase of the top load washer, we have had to call in repair. The lid lock and sensor have went out on the machine and the repair costs are equal to the purchase of the machine. Whether the consumer has an extended warranty or not, this is unreasonable. So hear this Maytag, the CONSUMERS will invest elsewhere when delivered cheap merchandise like this even if it is Made in the USA as you wish to tout in order to bait the consumer for their money instead of providing superior quality American products. This consumer is sending this machine out the door.

Maytag, you left me disillusioned and disappointed. I used to believe you, trust you. How am I going to feed my kids without a fridge? I bought our side-by-side French door refrigerator a few years ago and even bought the extended warranty (which no longer is in effect, unfortunately). Yesterday, the refrigerator failed, We called a small local repair person who could be at my home in a couple of hours. He listened and said my compressor was out, a leak was probably in there too, and that it would cost about 900 dollars or more to repair. When I called Maytag to see what they thought, they said that because I called a non-Maytag assigned repair person (even though this small-business repair guy didnt even take apart the refrigerator), I could no longer get their repair plus one year warranty offer which runs 400 dollars. But there is nothing I see on their warranty page that says this. Here I was trying to help our local economy by calling a small mom-and-pop repair person who is known in our town and has a good reputation, but I guess that by doing that minor well-intentioned act, it goes against Maytag corporate policy. Wow, how foolish do I feel now? I feel ashamed to admit this, but I actually started crying when I was on the phone with their customer help rep and asked, Isnt there something that can be done? I was thinking to myself that two months after Christmas with three kids is a tough time to replace a 1300-dollar refrigerator. I offered to pay the 400 dollars to get the refrigerator fixed by a sanctioned Maytag official with their warranty, but that I didnt know that I wasnt supposed to call anyone else besides Maytag if my appliances broke down. I would have never called our small local guy if I had known that Maytag corporate had such a policy. She said that no, there was nothing that she could do, and that is what happens to customers who call a non-Maytag assigned repair person. I guess when this happens to your fridge, you ask your neighbors if they can keep some milk, lunch meat and cheese for you, at least until you can save up for another fridge. Thank goodness that dried pasta and Ragu sauce dont have to be refrigerated. There are also cans of peas and corn and dry cereal, so it should be okay.I cant express how absolutely disappointed I am with myself and with my purchase, and how this has soured me on everything Maytag. I feel like an idiot. Can you believe that I had actually scrimped and saved up for months to buy this Maytag refrigerator and the extended warranty (hah, just to be safe)? I had bought it because I thought Maytag was a reputable company and because it was supposed to help the environment with its energy saving technology. But dont you think that a $1300 refrigerator should last more than 7 years (Believe it or not, this newer Maytag fridge was replacing a 20-year-old fridge that I gave to my cousins and which is still running to this day!)? And to add insult to injury, I already had a major repair done 4 years ago on this same French door Maytag fridge when it was only 3 years old. Maytag should offer to come out and fix their mess, but all I received when I called Robin, the supervisor, at their Tennessee call center was a, Sorry, there is nothing that I can do and there is no one else that you can speak to, and Nope, there is no one at corporate that you can call for help either and I have no advice to offer you. I can give you a mailing address though, if you like. I think I did hear pity in her voice, so that was some comfort. Pity from a call center supervisor, think about that! How awful it must be for her if that is all that she can offer to the desperate people who look to her for guidance! I actually felt sorry for her after I hung up the phone. It must be terrible to know that the company that you work for is probably mistreating its customers and all that you can offer is an Im sorry. I wonder how often someone says a rosary for her and her workers taking on those endless calls for help. How often does she cry herself to sleep after a day of that?I really dont like complaining online and I rarely do it, but this experience was just so awful and hopeless that I feel I had to say something to save other people pain and money. I hope that everyone learns from my miserable Maytag mistakes and please pass on my experiences to all of your friends and family. Those big tax refund checks will be coming soon, and I know that a lot of people upgrade their appliances with that money. Please, please think twice before you buy anything Maytag. I would feel better if I knew that people could learn from my stupidity. Remarkably, I was once gullible enough to trust and believe in American-made Maytag - goodness, was I wrong to do that. I am considering Facebooking my friends and family to let them know what happened and save them the heartache too. I hope that everyone who reads this can learn from my own mistakes and misguided trust in a company. In a world where so many companies throw away or roll over on their loyal customers, all I can say is something that I learned from a wise high school English teacher - Et tu, Maytag? .

The Maytag MFI2568AES refrigerators ice maker is broken and we cannot get a replacement unit. Whirlpool who now owns Maytag is of no assistance. The unit is two years old. I understand planned obsolescence but this is ridiculous.

The dishwasher stopped working. The lights on left side of control panel arent working; so, machine wont start. Then machine was purchased in January 2010 for $525 and not including installation. Kim says it will cost $129 for their repairman to come look at it. I wished I had read the list of complaints on your site first.

I purchased Maytag Bravos MVWX500XWO top loading high efficiency low water washer and it is a piece of junk. All my clothes came out horribly wrinkled and ruined a white jacket when I used the color safe bleach dispenser. I purchased the machine from Sears, where I purchased the extended warranty. I had an A&E technician out and he explained that the new technology of machines are expecting all clothes to be dried in the dryer. Okay, but what do you do with clothes that say hang dry and they come out so wrinkled and twisted that even an iron cant get the wrinkles out? Another suggestion from the technician, put the hang-dry articles in the fluff cycle of the dryer. Well, thats a big nugatory since they are supposed to hang dry them. Supposedly, this machine is all about energy efficiency but isnt it a contradiction when you are using more energy with running a dryer? Someone suggested to me that perhaps there wasnt enough water being dispensed during the spin cycle resulting in horribly wrinkled clothes. Either way, I am on my last nerve with this machine. I always thought that Maytag was an elite company. Well, how wrong I was! Their customer service is pretty much not customer-oriented. Its all about the almighty dollar. After speaking to a supervisor, she explained to me that I should contact Sears with my complaint that Maytag had no recourse. Well honey, Sears did not make the atrocious machine. They are just the so-called messengers. I have unfortunately found that once Maytag sells their horrendous product, they dont even stand by it. Now isnt that typical of companies nowadays and sadly, lacking with this company? Pride in their workmanship! And again, its all about the almighty dollar and who gives a ** about customer satisfaction? Maybe thats why they dont have the Maytag repairman. He was ashamed to be associated with this irreverent company.

I have only had this machine for 2 weeks after having a Maytag since 1994. Even broken, my old machine was far superior to this one, a Maytag Bravos. Fortunately, the salesman noted that I wouldnt be happy with this machine but, thanks to a government mandate, all new machines behave in a similar manner to save water and energy. This agitator-less machine neither washes nor rinses the clothes/bedding/towels properly. It takes four times as long to wash the items but doesnt get them nearly as clean. Today, I put 2 pairs of shorts, 2 T-shirts and a standard bed-sized mattress cover in to wash. The mattress cover never even got thoroughly wet even though I used the deep wash and extra rinse settings. Last week I put sheets in the sheet setting only to have them come out totally wrinkled and stiff as a board with soap even though I used the recommended amount of detergent. This is a disaster. Shame on Whirlpool/Maytag and the U.S. Govt. A river and a flat rock would work better!

I purchased a Maytag gas stove. Right away I noticed the oven racks would sag in the middle pulling the back corners to pull away from sides dropping the rack down on top of rack below. I got a hold of Maytag and they sent me out a set of 3 new oven racks that were exactly the same as the ones I had. I have been fighting with them for years. I called Whirlpool today who make Maytag and was told its off warranty and that I can order another set of oven racks at a cost to me. They would be the same as I have. The racks are so cheaply made and cannot stand even a few pounds. The finish on the stove also chips very easily. You rub a pan up against it and it scratches the white porcelain off. I spent a lot of money buying the dream gas stove I had thought, but only to be unsatisfied with my purchase. Buyer beware of Maytag products.

Worst washing machine!!! I purchased the top loader Maytag Bravos washer HE in 2011 and they are the worst!!! It has been repaired three times already and now is making such a loud noise and I have been told it is the bearings. I did purchase the extended warranty and it expired. The reason I did not get a renewal is Maytag & Home Depot do not allow the the extended warranty company to let you know the warranty is ending. So now I have a 3 1/2 year old washer that needs bearings and will cost $500 + for repairs. Will not be spending anymore money on this absolute piece of junk. I had a Maytag that was 22 years old that I replaced and thought I was buying the same quality but never again another Maytag. This company may want to employ only repairmen because you will need only them because no one should buy a new one going forward.

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

My $1500 2 yr old Maytag mbf2258Dem refrigerator stopped cooling properly (wont freeze). The icemaker was the slowest I have ever had. That may have been the problem when I bought it. The Maytag Repairman came out and said that even with Maytag sending me a new compressor (under warranty) this unit was not worth fixing. I called Maytag and they said sorry there was nothing they would do. So l looked up every review I could find... and this refrigerator is just bad. Not Worth Fixing. So Maytag deceived me. On the front of the door it says 10 year compressor warranty. Thats a big sales feature! They know that they have a problem. This is one bad company!

I am a regular customer of Leons and used to buy all my home appliances from them, because I trusted their quality and service of their products. However, last time I bought French Door Maytag refrigerator from them, about two years ago, we suffered from defects in this type of fridge. The problem started before one year when my wife saw some leakage of water on floor in the front side under the fridge freezer door. In the beginning, this was occurring once a month or every two weeks, so she didnt think it would be a problem or it might happen occasionally. However, the water leakage now became worse and almost every day. We had to put a towel permanently under the freezer door to dry the water which appeared ugly. Also, I had couple of accidents that my child slide over because of that water leakage. I spoke to one technician, he told me resolving this type of problems is not guaranteed because the problem will appear again or after while. He said this could be a manufacturing defects in this type of Maytag fridge models!!! Another problem appeared also one year ago, that one of the door handle started to shake very little, but now it looks like moving from its position and there is no way to fix it!!!Therefore, when I requested the help from Leons they told me that, You didnt buy the extended warranty and we cant do anything for you!!! You can talk directly to Maytag. Then, I send email to Maytag explaining the problem. They even didnt bother to reply or call me. Now, I feel that I was bluffed by these companies. I didnt think that I was buying a $2,000 refrigerator to scrap it after two years. That is ridiculous when you buy defected product from them, but they dont care to resolve the issue.

Maytag model #MDB6949SC, purchased Feb 22, 2015. In early May plastic parts from the top rack wheel assembly broke. Assembly unit replaced at no cost through the 1 year warranty. (cost = time and effort to arrange replacement with repair person). Same parts broke again in November - replaced at no cost again under warranty. Warranty expires in two months. If past performance indicates future performance, this part will need replacing twice a year at ~$140 per visit or $280 per year. Not a good thing. Called Whirlpool and with several calls and emails. They offered an extension of a year on the warranty. I think using plastic for this wheel assembly unit is a design flaw. Would not recommend this dishwasher.

I purchased a Maytag front loader washer less than a year ago. Based on their deceptive advertising, Maytags rarely need service (model MHWE201YW00). There was a loud banging within 11 months. I called service for the additional warranty I purchased. The service man told me this machine is shot. The bearing completely broke and the drum was loose. They ordered 3 huge boxes, 3-1/2 feet cubes delivered to my house. I had to drag them into my garage where they have been sitting for two weeks. I am now 4 weeks without a washer with 4 kids. Ive called Corporate Headquarters and have spoken to their Corporate Board Gwenn and Jackyln who seem to think they can diagnose the problem. I told them the machine smelled like it was burning and the last load was dripping wet and the clothes smelled burnt. This is a stackable in my kids bedroom and I told them I was concerned about an electrical fire. Ive already missed one day of work for this. I am now being told Jan. 11, 2013 is when it can be serviced. That would be 2 months without a machine. They are willing to endanger my children with wet wires and an electrical fire. Mr. Fettig is impossible to get in touch with and this customer service center apparently has no supervisors. What they say, goes. A class action should be started against Mr. Fettig and his team of crooks who are putting crap out into the market place, falsely advertising it and then not backing up when their product breaks less than a year and becomes a possible hazard in someones home. Ive sent to his home address a UPS letter to Mr. Fettig, letting him know if a fire starts in my home due to water on the wet wires (water that got behind the drum because of the faulty bearing), water that was leaking from the bottom of the washer that I hold him and his company personally responsible. They have been alerted to the problem numerous times and ignore it. I spoke to their Safety department and I asked what to do if I smell a burning smell when the machine was running. They told me to immediately shut it off and unplug. Yet Whirlpool is trying to put a Band-aid on a machine that has already been infected with water damage to the wires. This has been such a frustrating, stressful experience. Even 5 weeks from now, when my replacement parts are put in, I will worry each time the machine is run if there will be a spark from the damaged wire. Something must be done legally to stop these crooks from doing to this and getting away with it. All they care about is their profit margin. The Whirlpool creed to their customers is a bunch of bull! Mr. Fettig vacations at his home on Dolphine Island, Alabama while hardworking people are scrambling around trying to figure out what happened to their new appliance that promised to work but is broken in less than a year. He vacations at his home in Florida while the hard-earned money you spent on his product is a waste.

I have a new Centennial Maytag dryer. What a horrible sound it makes when the time is up!!! I had another Maytag dryer for 19 years and it did not sound as obnoxious as this new one. HELP!! I can tell some man invented it.

Maytag stove MGR7662WW - I purchased this stove about 4 years ago. Now, the stove will not light. I called in to Maytag only to be told I must pay a service fee or purchase a repair manual. It’s very strange. My old Kenmore lasted 22 years and here I thought Maytag would at least last 10 years less than half the life of my old stove, realizing products today are not what they used to be. Maytag, the dependability people, I guess that old Maytag commercial where the Maytag repairman is so bored claiming no one needs service for a Maytag product is really false advertising. Buy American products; I’m not really sure who is the current country who is home to the great Maytag corporation. I guess me and my wife will spend another $700 on another brand stove and try this process all over again, hopefully not again in approx 4 years.

I had the washer repaired twice in January, once in April and again in August, the same repair wire coming out of harness. I had to pay a second time before Willie, the repairman, finally put a longer wire on the harness. Maytag told me they would send a new repairman after I called to complain. All 4 times, its been the same man and it cost me money. It seems like a bait and switch with the repairman. I called both A& E and Maytag. Both refused to refund the $129 second charge because it was more than 90 days. I say its been the same issue, repairman is a scam when they dont fix it right and charge again. I had another man there who knows about repairs and finally told the repairman to change out the wire or it wouldnt have been done this time either. I do want an attorney to contact me about this as this is wrong. Im going to file a complaint with BBB.

I moved into my home in July 2013. My kitchen came with all stainless appliances that appeared and seemed to be in excellent shape. I have been using the Whirlpool Microwave oven to heat foods (all in microwave safe) containers and dishes. This morning, I was heating a muffin, when suddenly I hear popping. When I looked through the glass into the inside of the microwave I saw sparks then flames. I immediately stopped the microwave. The fire apparently started in the area of one clip that holds the metal rack inside. In researching this issue online, I found hundreds of complaints from people who have experienced the same issue, and Whirlpool refused to replace the unit because it is out of warranty.

I purchased the Maytag MFI2670XEM0 3 Door Refrigerator in Oct 2012. Thank God I purchased the extended warranty. The freezer has had issues with improper sealing since I bought it. It builds up ice around the bottom of the freezer where the seal meets. So bad it prevents it from closing. It happens fast, so I have to scrape it off every week minimum, to keep it closed. They have replaced the seals twice, all of the slide rails, twice and it still doesnt close right. I thought when I moved to Florida, I wouldnt have to scrape ice.Next: Ice maker quit working and had to replace that. Now, I came out this morning and about busted my ** when I slipped on all the water flooding my kitchen. The ice maker has a stupid little fitting on top of the refrigerator that has a rubber bulb connected to the ice maker water line. It split in half and every time the ice maker cycles, it pours water out that fitting and down the side. Why in the ** did they design it like that? It has caused damage to my cabinets and tile floor from running under it.Im sick of this appliance. I thought Maytag was known for quality. What happened to that? What a disappointing piece of junk and Im stuck with it unless I want to put out money for something different. There should be a Lemon Law rule for appliances like this. I have asked and get nothing from the warranty service but silence (crickets). They are sending out a tech again but that will require two service calls because they always have to order parts, which takes 2-3 weeks. Ive had to call them at least 5 times, which has amounted to no less than 10 service calls and here we go again. Stay clear of these units at all cost.

I wrecked on a bike, had surgery and in a wheelchair. I bought and had a Maytag dishwasher delivered from Beaumont Home Depot and this mdb7749sbw2 model never never worked. Home Depot told me I had to bring it back myself (Im in a wheelchair at the months that was impossible) and I called Maytag warranty. They sent a tech. He replaced a front power panel that didnt work. They sent out two more techs and they said use other soap Lemi Shine and the other guy said use Finish and turn your hot water heater all the way up. That never worked either. I have had this a yr and it just sit there and money in the trash. It makes me sick.

Maytag HE Top Load Washer - We bought our whole house lot of Maytag appliances 6 months prior to when we would need them, in Nov of 2015. There was a great Canadian Black Friday sale event special, so we purchased the whole lot at Home Depot thinking we had got a great deal, however back then there were very little reviews on the washers, as they were fairly new. This is the absolute worst washer, I have to pause the washer after the water level that the sensor allows finishes and add at least a bucket more of water to cover the clothes and clean them properly and rinse them twice to make sure the residue from the soap gets washed off (I use HE pods, so not using too much soap). Certainly not what you would expect when you buy a high-end appliance. Im going to replace it, but I cannot even try to recoup any money back, as I couldnt/ wouldnt be able to sell it to anyone knowing that it is just garbage!! You would think that a high-end appliance company like Maytag would admit that this appliance is a mistake and offer the consumers that purchased this junk a credit towards a washer that will do what is expected!! Think about it Maytag... you have lost a lot of future business by ignoring the fact that this machine is not what you advertise as a company that stands behind their name. I am sure to tell everyone that I know about the disappointment in this product. I have a friend that has a LG HE washer and it works great... so no excuses about water consumption regulations... its just not designed properly!!

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

The washer w10420491A is 2 1/2 years old and got the F51 code. The result is the hub bearing are shot along with a circuit board. I would stay away from any Maytag Bravos washers.

First off, the drum split apart on the dryer. The drum part was not in this country, so instead of going ahead and replacing the clothes dryer, they told me to hang the clothes outside for six weeks or whenever the part comes in. That was three months after owning the piece of junk. I was having a bad day already, so I basically completely lost it. Im surprised I didnt get arrested for that. I wont ever lose my temper like that again. The clothes always smell bad, and sometimes really bad. Now, I find out that both washer and dryer could cause a fire. They are sending us a couple of really cheap GFCIs to keep them from a liability issue. Maytag is the absolute worst!