French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

Purchased Maytag dishwasher Model Number MDB7749AWM1 in June 2011. With a two person household, we need a new control panel in Sept 2014. Total cost of service call, repair and part is $325. This unit was a poor value for us. I see the trend is to discontinue a model after a short period of time, making it impossible for anyone to get a review of other peoples experiences. I went with Maytag because of this. It was a company with a strong reputation for quality equipment. Not so anymore. I would not purchase another product made by Maytag.

Can not wash 4 pairs of pants or 2 sheets because they get out of balance when the spin cycle begins. I had to take the clothes out and move them around to keep the balance. Very unhappy. Would not recommend this washer.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

Just purchased a maytag dishwasher from home depot. I did the install myself. The dishwasher will not work at all the panel lights up, but no water goes into the washer. I now must wait two days for repair. After reading all the other reviews, I am thinking about returning it for another brand. And yes the water supply is on. I have hooked up several dishwashers. This is the first time a brand new one did not work right from the store.

I have the Maytag Gemini Double oven 5 burner stove. It is great! I use the smaller oven more than the bigger oven. Holidays and cooking are a lot nicer with my range oven. The turkey can be cooking in the lower oven while pies are baking in the smaller upper oven. I have had my range for a while now but I have not once had a problem with it.

I love the way it can really handle large loads. The dryer is the best though. It actually dries your load without you having to turn it on more. There are many different choices that handle drying. So, no more to the bone drying.

Faulty Maytag Bravos electronic dryer model MEDB400VQ0 - I purchased a new Maytag Bravos washer and dryer in Feb 2011. About 3 weeks ago, I noticed the dryer not drying my clothes. They were hot, but not dry, leaving them hot and steamy. There was also wet lint that kept accumulating inside of the dryer. I took the back off of the dryer to see if there was an obvious problem and I found the blower belt and large bolt that holds one end of the belt to be off and laying on the bottom of the dryer. I have also looked online and did a search on this make and model and the issue I was having, it brought numerous people having the same problem on multiple internet forum sites. Apparently, there is also a service bulletin on this exact issue, but according to the Maytag customer service department, no recall. Therefore, I am out of luck as far as getting any kind of repair (unless I pay for it) because I am out of warranty by 3 weeks. I purchased the Maytag brand thinking this was going to be the best and will last me a very long time. Unfortunately, I was wrong. It only lasted me one year without breaking down and the customer service department is horrible. You can tell they definitely dont stand by their name, the Maytag name is a thing of the past. I will never recommend this brand to anyone else for purchase and I regret having swayed my mother to purchase the very same set I did. This has been an awful experience and I am wishing I had chosen a different brand. Maytag leaves me angry and very much dissatisfied.

Bravo XL - This is the worst washing machine I have ever purchased! Loved it at first but after a year or so we couldnt wash a full load without error messages. Then we couldnt even wash one pair of jeans without an error message. Called to have it repaired and $300. Later the bearing was replaced and the washer worked wonderfully once again. Less than a year later and we are back to having a non functional washer. Cannot wash anything without the error message. Customer service is absolutely no help. For such an expensive washer and supposedly a good brand, this machine is a real disappointment.

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

We built a new home in 2008 and purchased a Maytag appliance package from Home Depot, including a dishwasher, stove and refrigerator. From the beginning, we had problems with our French door refrigerator (MFC2061HEW; it has been discontinued). Within the first year we had 3 ice makers replaced because it was not making any ice. Now, mind you, we went through Maytag to have their repairman to service our appliance and they set up all the service calls. We limped by for awhile and called a different repairman to come and check the fridge because it was not staying cold or making ice again and, of course, it was out of warranty. The first thing he did was check the freon and we were told that it didnt have enough freon to keep it going, so he recharged it and it worked great. We have had to have the repairman come back again this month because it stopped making ice and the temperature for upper and lower was all over the place. He checked the freon again and said the unit has a slow leak in it and he was unable to fix that. I contacted Maytag because I felt if the first repairman had checked the freon from the beginning, we wouldnt be having this problem. The only suggestion I got from them was call a company with a dye kit test and that they are sorry, but its not under warranty. I dont know about anyone else, but $2000.00 for a fridge that has been a pain since day one is a lot of money to replace. I feel they dont care about their customers and they should be responsible for paying for the repair that should have been caught from the get-go.

Bought a Maytag Bravos XL washing machine because I thought it was a dependable brand. We have had it 14 months and the lid (upper left corner) will not stay connected. I called Maytag and the rep states to me Is it broken in the upper left corner and I replied yes. He continued he is just the parts guy, but every bravos has the same problem. I asked for the replacement part ($302), but he said the part is on back order for 60 days. He continued that maybe I should buy two because it will happen again. I only paid $700 for the washer, but it should never break down after 14 months. I highly recommend a different brand.

Love, love this washer. Does an amazing job cleaning colors, whites, and bulky bedding. If you like Tide Pods or other liquid pacs, this might not be the washer for you as they tend to end up inside the gasket. Powder-filled pacs are no problem however.

My 6 year old Maytag 3000 series front load w/d set started leaking after 2 years. Minor leak on certain wash settings such as Rapid Wash setting that worsened (and I could live with), so that setting wasnt used. Last month the washer door was flapping open DURING a spin cycle. I stopped machine only to find the entire barrel had dropped and metal wire wrapped around clothing. Worst washer ever!

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

The washer does not wash good on the initial wash. I have to wash my clothing twice. Cost and time consuming. The washer is “HE” and the water level is never enough. My clothes be saturated with dirt/lint scum and I never overload my washer. HELP!!!

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

I purchased a bottom freezer Maytag refrigerator two years ago. It recently began leaking water onto the floor from the freezer compartment. I just had it serviced and the serviceman told me that it was a common problem. The duck-billed check valve gets plugged. This is a problem with Maytag, Jenn-Air, Whirlpool, Amana, and KitchenAid refrigerators as they all share the same manufacturer. There is a service bulletin out on this that lists hundreds of model numbers affected by the problem (Technical Service Pointer #: W10632338). I think it is criminal that consumers are expected to pay hundreds of dollars to have this manufacturers defect repaired. I tried to find a place with the government to file a complaint, but wasnt clear who had jurisdiction. Perhaps a class action suit is in order. There have to be millions of consumers potentially facing this problem. Anyone with any knowledge of how to further pursue this defect, please comment.

Ive tried all manner of washing clothes, especially dark ones. Different cycles, different detergents and amounts, but it always leaves scum marks in folded places. I have to either brush off what I can, and/or rinse the clothing in a sink and then rewash the clothing without detergent. In an attempt to save water, I end up using two or three times the amount.

Maytag, you are still trading on your good name but that will not last! I owned a Maytag, agitator style, for 20 years and it was still running just fine when we built a new house. I thought it would be wise to buy new appliances for my new laundry room so I chose the beautiful and expensive Maytag Bravos XL. I regret that decision. The washer lasted 4 years and began to have problems draining last week. The liquid that stayed in the washtub until the repairman could get here was so foul smelling! He came back today to replace the drain pump and now the washer is showing that the interface and CCU are not communicating. So now we are ordering another CCU and I hope this fixes the problem. I agree with all of you who say you will NEVER buy another Maytag again. Maytag, are you listening?

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

My dishwashers warranty expired in March 2011 and it stopped running in April 2011. I have not had the use of my dishwasher since then. I was able to finally afford to have a technician take a look at it. I am told that it is the circuit board and it is going to cost as much as the price I bought the dishwasher for. I thought Maytag products were better than the other products so I paid a little more and got a Maytag only to find out that they are garbage. I might as well bought an unknown brand at a cheaper price for all your products were worth. I guess you cannot trust anyone these days, and I will never buy a Maytag product of any kind again. I think that you should fix this.

Maytag Neptune was purchased over 15 years ago to replace GE, which we purchased when children were little. I wanted a step up in quality. I remember paying around $499 for this unit. This is an analog unit. The intellidry feature has been a real asset, protecting our clothes from over drying. We have had this machine for nearly 20 years. It has been real reliable, sometimes drying 20 loads a week. Large capacity, but has to fit down a narrow and twisting stairway. Must be energy efficient, have good reviews and decent price. We always look for sales or buying incentives. Brand is secondary to quality. Knowledge of an appliances historical reputation is important. I would look at reviews, especially concerning cost of repair. I would attempt to get a hands-on view, before purchase from a reputable supplier at the best price. My dryer has only required one major repair in the time Ive had it. A few years ago we replaced the motor and blower, and I have personally replaced the drum support rollers twice. I hesitate to replace this machine, because the analog controls have proved very reliable.

Same as all the others, bought this dishwasher about a year and a half ago for a new home. Didnt get the CO until 3 mo. ago and already having same problem with the keyboard flashing and not working properly. Very pathetic to believe less than 100 washes and were going to need a new washer, that works out to be about $ 5.00 a load. Wish someone could help. Model mdb7749sbb0. Thanks.

My husband and I bought a Maytag 3000 series front-loading washer in 2009. In either December of 2014 or January of 2015 it broke down. We had a repairman come out. The inner and outer tubs and a bearing needed replacing. He said it would be expensive and some of the parts were no longer available. In his opinion he hated these new machines as they were nothing but problems. Next we contacted our dealer whom we bought it from. He contacted Maytag himself, then he gave us telephone number to speak with. He no longer carries this brand because of problems and said our washer was no longer made because of problems. So we call, spoke with several supervisors in customer experience. They offered half off another washer of similar value on Maytag or whirlpool brand. Maybe Im being difficult but I didnt plan on buying a new washer after 5 1/2 years. When I and my husband ask to speak to next person in chain of command we were told there wasnt one. Really!!! She would not pass us to a higher authority. She read a classic... Im sorry for your experience. Were offering you a great deal considering your warranty was out. Im hoping this will keep anyone else from this Bad experience.

I purchased by Maytag Bravo from Lowes exactly 1 year ago when the gearbox failed. There was a loud grinding sound as the washer tried to shift from wash to spin. Reading through some on-line reviews and complaints it turns out that this is not a new problem and has been known to Maytag for some time. I specifically bought a Maytag because of their prior reputation for quality. Unfortunately, my information was out of date. It is so sad that a company would compromise such an outstanding reputation.

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

We purchased this Maytag washer. My wife liked it at first, but after a few months she kept complaining the wash stinks, and I can also say that. I complained to my wife about the smell of our wash, especially the wash towels. The wash was turning colors and some we threw away. My wife has been complaining about all this for months and years and said she will never buy another washer like this. Then about two years ago, she was having trouble with codes coming up. We called service, but didnt get any help, so I looked on internet and found the problem with the code. I took the washer apart and cleaned the tube out and the washer worked, but every now and then my wife needs to climb over washer and unplug, let sit, then replug back in and start it to get rid of code. My wife and I are very upset with this washer!

Had a brand new Maytag MDB4949 dishwasher installed on 10/20/15. Noticed an acrid smell of burning plastic coming from the pull handle. After going to the reviews I see a pattern of shorting control panel boards melting the ribbon cable. Having repaired Xerox copy machines for 17 years, I recognized the smell of an electronics short and melting plastic. There are 600+ complaints for the same thing. Going to call the store we purchased it from and will escalate from there.

We purchased our Neptune washer and dryer combo MLG2000AWW from Circuit City in 1999 for $1900 also purchased the extended warranty. Here we are 15 years later and time to replace with new Samsung units. Besides having the main bearing replaced after 6 years in service, and having a sensor and a switch replaced on two separate occasions all covered by the warranty, our Neptune provided exceptional service throughout the 15 years. My understanding was that Maytag was bought out and run very poorly in the early 2000s as our unit was produced prior to that time... when Maytag was Maytag.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

Maytag Free Standing 30-inch Gas Range - In 2004 we bought our model MGR5775QDS gas range with 5-burners because it offered the most BTU variety for the price: 1 burner with a high BTU (16K), 1 with low (5K), plus 2 in mid-range (9.5K) and 1 with 12K. Within half a year of using the oven, we turned on the self-cleaning function. Big mistake. One cleaning cycle later, our oven refused to ignite. The cleaning cycle burned out the ignition unit. Cant remember if its replacement then was under warranty but the repairman said this was a COMMON PROBLEM with Maytag and we best not use it EVER. In 2014 our cleaning lady mistakenly thinking she was doing us a favor, set the self-cleaning function. Once again, the ignition unit was destroyed. This time its replacement was $350 with part and labor. One and half months later, the oven is again non-functioning. This time our repair guy said the part is a very minor, inexpensive one BUT MAYTAG IS NO LONGER MAKING IT!!! The only way well get our oven back is if he can find another model and cannibalize it to fix ours. Are we disgruntled? Yes. Would we like to see a class action suit against Maytag for knowingly manufacturing a gas range with a malfunctioning self-cleaning unit that destroys oven parts? Yes. Will we ever again buy Maytag? Not on your life. A once stellar manufacturer gone down the tubes with a growing reputation for making junk. American-made appliances mean zip these days. Thank you for nothing, Maytag.

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

Washer goes off-balance even when clothes are evenly distributed in tub. When it is turned off to rearrange clothes (which may have to be performed a couple of times), washer goes back to starting cycle which means more water. Afraid to do laundry unattended.

Bought a Maytag washer MVWC415EW in 4/2015. We dont use the washer heavily but over that time span the paint on the top cover and the side where the cover comes down has bubbled up. It looks like a bad rash but only on a washer. I think the company used inferior paint which can bubble up with the heat of the hot water during the wash cycle. I called the company but they do not cover cosmetic items on the warranty. I think since this was a flaw in the paint used they should at least replace the cover portion which would be an easy fix. Maytags are not what they use be! Last Maytag lasted 17 years with no paint problems or mechanical problems.

We ordered a new Bravos washer and dryer at the end of November but due to delivery snafus, we did not have both until the second week of December. Just yesterday, both failed. Part of the drum on the washer ripped off, and the dryer just stopped running an hour later. I am used to getting a long life out of appliances. The old dryer was over 20 years old, and while the old washer was only 17 years old, I thought it would be nice to get a matched set.

I have a major complaint with the Maytag double oven design. With the smaller oven above, if you spill any liquid while taking something out of the top oven, the liquid drips down between the two panes of glass on the lower oven door. This makes it impossible to clean. Maytags reply - call a service rep and have him make a house call and take the door apart for you and clean it. Not warranty work so I would have to do this every few months. Also, when baking in the upper oven, cakes and cookies tend to overcook on the bottom as the dishes are so close to the element.

I bought this Centennial washer about 7 weeks ago and it has worked right for 4 of those weeks. The washer wouldnt spin the clothes and they came out soaked. Service guy came out and said it was the computer panel and he didnt have one. So I waited over a week for another service call. He put that one and said that now the transmission was shot and he didnt have one, another wait. This is a piece of junk. Do not buy Maytag or Whirlpool products. I had a Maytag for 15 years and had one service call. They are not what they used to be.

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

Like everyone else got that French door fridge and was also duped on that 1 yr warranty - a 95 dollar repair visit for a 485 repair job on a 1200 dollar purchase. Shame on them. Im gonna fix my new floor and replace that frozen bottom, leaking on the left, non-working ice maker 2 yr old refrigerator. Very disappointed with the whole thing and sorry for all of our losses.

Maytag 2000 series front load washer - f you are looking for a front load washer DO NOT buy a Maytag! I purchased a new front load washer dryer set late 2013 and have regretted to washer ever since. Continual electrical problems, door gasket needed replaced almost immediately AND the worst part is that it has ruined over $1000 worth of clothing due to it trapping cloth between the drum and door and wearing holes in them. No matter how I load the clothes or sort them it continues. I have contacted Maytag and was told I have no recourse as the warranty is over. I was very disappointed because I have had Maytag products in the past and had no problems. Please, think twice before buying this washer! It will cost much more than just the ticket price!!!

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

Clothes do not turn over in the wash cycle. The clothes at the bottom get plenty of hard scrubbing from the agitator but the ones at the top barely get wet and never move down to the bottom. Insufficient amount of water enters the tub. The repairman says the washer is working as designed. Neither Maytag or Lowes will take back the washer. Worst appliance Ive ever owned. Bummer!

I bought my microwave in Nov of 2015. We began having problems in April 2017. When you cook or warm something up it gets hot. The light wont come on and the display continues to say open/close door. After about 4 hours of cool down time it may or may not restart. After contacting Maytag I was told I should have purchased the warranty. They also informed me that they do not have repairman in my area. We have just replaced all appliances with Maytag so now I am concerned they are all junk. We did buy warranties on the major appliances, but how will they repair with no repairman in my area. Maytag used to be the best appliances but after this experience and now I have a broken microwave after only a year and a half that they dont stand behind, I will never purchase any Maytag again. It also seems that this is not the only issue they are having with their microwaves. I have contacted my Lowes where we purchased and they even made a Maytag call with no results. Maybe the suppliers should stop promoting and selling their items. We replaced a 22 yr old Kenmore microwave that was still working thats why this is so heart breaking. Stand behind your products. No wonder you dont have repairman. They would never get a day off from repairing your junk.

In the last 6 years my husband and I have bought the high end front load Maytag washers and both have crapped out within the year. I will never buy another product from this company again. Their customer service was no help and the washer needs to be rebuilt. We are waiting for parts which are back ordered months in advance. I will have no washing machine for at least 2 months. I do not trust any product made by Maytag and any company who sells Maytag should be ashamed to sell their product. There is nothing that I have experienced that would make me trust this company whatsoever!

We purchased a Maytag dishwasher in July 2013. In October 2014 it stopped working. None of the buttons on the control panel would light up. The service technician diagnosis was that it needs a new control panel at a cost of about $200.00. We chose not to do the repair since the technician recommended against it.

Ive owned my Maytag Neptune front loader since 2003. Since then, the whites have either turned gray or yellow. Ive tried minimizing the use of Tide HE, maximizing its use, and I still get the same results. Can anyone please assist me with this major problem? Ive owned Maytag appliances since the mid 60s, and I know the quality isnt there anymore.

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

My Maytag washing machine is nothing like the ones that my mom used to have. This thing is loud as it click, click clicks through cycles. Being a mechanical engineer, I assume that parts are taking a beating inside that machine to make all that noise. Then comes the wash time on this thing. With water level on auto sensing and one rinse, this machine takes over an hour to do a batch of wash. It literally stops dead for at least a full minute between each cycle then click, click, clicks its way to the next. It does not rinse very well as more often then not there is soap scum on the clothes when the washer finally stops. SPEND A FEW DOLLARS MORE AND BUY A DIFFERENT BRAND! Maytag is garbage!

I purchased the Maytag oven in January and have had the service technician out 5 times to try to repair the oven because it doesnt heat properly. Theyve told me that because I live in a condominium that it is normal for the oven to take an hour to preheat, then another hour for the second oven to preheat. When I am baking the oven does not hold the temperature and anything I bake takes much longer than it should. They refuse to get me a new oven.

Buyer beware. This machine has received several complaints. Not long after purchase, the washer started to stop during the fill cycle and give an error code no. This is supposed to be sure to overloading the machine. The other reason they give is something stuck item the baskets. Again not the case. Supposedly it must be a motor issue. Maytag was my trusted band. Our last Maytag lasted us almost twenty five years.I was excited to get this machine but disappointed with the lack of clean clothes, error codes, and noisy operation. My first clue should have been the one year only warranty. Thats how much they believe in their products. Ill never trust Maytag again. So sad that whirlpool should sabotage the Maytag brand and turn an otherwise great washer manufacturer into a piece of junk manufacturer. Dont buy whirlpool either as thats how much they care for customers.

The dishwasher would not start July 30 2015. Tried to get service around here and no shops could respond. Called Midsouth Distributors for circuit board. They did not have one but would order and gave me the part # W10595570 based on the Model # MDB7749SBW3. Hoping could find one quicker somewhere else. Ordered one overnight from Sears and planned to replace the board by myself. However, I noticed the flat wire with 14 wires in the ribbon cable had brown spots. From my experience in the electrical systems, I realized this must be shorting out the start signal to the dishwasher logic controller. Sure enough, after scraping this off with a sharp knife, I was able to start my dish washer.My previous MAYTAG lasted 20 years. I bought this one in February 2014 at Home Depot. The design for the electrical controls is obviously very poor as testified by so many angry owners. MAYTAG should be required to replace all these control panels with a improved design at their cost. I hope this obvious poor design of a part gets attention in the United States and ConsumerAffairs will help us. I have called 1-800-688-9900 and registered with MAYTAG a complaint about this poor design.

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

I purchased a Maytag dishwasher delivered in dec 2012. We are snowbird Canadians and the dishwasher is only used 5 months per year. Jan 2015 the control panel quit working and the repairman tells me the wires on the control panel have started to melt down. He called Maytag and was told they had extended the warranty on this machine for one more year. Missed it by 2 months. Considering this was only really used one year, I am very disappointed. How can an extended warranty on a safety issue only be for one year? This is my first Maytag product and will be my last. I only purchased it because I was told Whirlpool bought them out and I have never had a problem with Whirlpool.

I have owned this Maytag washer model # MVWC360AW0 since Dec/2013. I do not have a single complaint about this machine. It has worked flawlessly for 5 years and am very happy with it. I just follow common sense maintenance like cleaning it once every month (do a full cycle with just borax & baking soda 1/2 cup each) no clothes of course. Another thing I do is to leave it open after I am done washing so it dries completely before I close the lid. The washer looks and works like new, cant be happier...

We have a Maytag Dishwasher Model MDBTT60AWB purchased from Lowes about 8 or 9 years ago. This model was included in the huge 2010 recall of 1.7 million units due to the possibility of heater-unit fires. For the last couple of years, its had a problem staying on the selected cycle: After being started on normal wash, it reverted to rinse only after a few seconds, but eventually quit responded to the selection of other cycles altogether. Removing the back from the door to expose the innards revealed the ribbon cable that connects the circuit-board head to the control panel had worked loose. Reattaching it provides a temporary fix, but it eventually works loose again. We suppose the screw holding the back to the door will strip sooner or later, but by then well probably be so fed-up with fixing it that buying a new (non-Maytag) one wont seem like a bad option.

We have had this refrigerator, model MFI2665XEM7, less than two years. The ice maker stopped working and we had it replaced at least 6 times in a two month period. We had a solid ice sheet in the bottom of the freezer drawer and it leaks water on the floor constantly! Even today... after another ice maker replacement, we have no ice! I never wanted a Maytag, but finances and the small space we had gave us little choice. I am not sure what our next move is. I will NEVER buy a Maytag product again! I should have google this sooner and we could have saved the poor repairman all of those trips!

We are a family of three. We purchased our Washer and Dryer New, November 2011 at Lowes, in Lindale TX. I am disabled. I have had several spine surgeries and getting ready for another. I was injured at work and it left me crippled. I do not receive any benefits from my County Employer. My wife is a schoolteacher. We live on a limited income after my accident. We purchased this set with utmost confidence, our last set was twenty years old. We updated due to water, electric, and the environment. Our Maytags we had were still usable, it was just time for their retirement. They were hand me downs washer and dryer set. Truly! I dont know how old they were. When our washer started having troubles, it was making a horrible noise. We called Hughes Appliance. Theyre an authorized Maytag Repair Service Warranty Center. They sent Mark out we used them before. He stated the motor was not loctited from the factory. It worked its way loose almost coming completely off. This cost me a $85 service call. Mark also stated that the Tub Bearings were going out because off this. He called Maytag Customer Service and Dealer Warranty Service, said they wouldnt pay for the repairs or even the Service call for their factorys snotty WorkmanShip. I tried calling myself and got absolutely nowhere. I was polite, courteous and nice and they still Said, Sorry, We Know its less than three years old but thats the way it is. Sorry Sir! Have Nice Day! Its going to cost $389 to replace the tub bearings in top load washer. The washer only cost about 750 less than three years ago. Its the most expensive clothes washer Ive ever owned. One thing! If they dont make things right, I promise I will never own a Maytag again! And when I am in a store and see someone looking at their product I will make a point to tell them my situation and about my Maytag Washer. One thing is certain I can make sure young customer dont buy the wrong appliances while I sit patiently in my wheelchair waiting on my wife. Thanks Maytag! Its not What You Did For Me! Its What I Can Do For You!

The control panel went bad on our Maytag dishwasher of only 4 years that is only run about once a week, A replacement part would cost more than half of what the dishwasher originally cost, so we have decided to go with a KitchenAid. Not pleased at all with the longevity of the Maytag.

I have had my refrigerator freezer for 2 1/2 years. It worked fine until about 6 months ago. The vent started freezing and then water ran to bottom of freezer and freeze. If I get this fixed, I hope that will be the end of the problem. I am going to defrost it the old fashion way to see if that works. I will never buy this product again.

We were replacing a 4 year old Whirlpool Duet washer (bought on recommendation from sister-in-law) that needed the third repair and was putting holes in our clothes. We had purchased the warranty (which we had never done before) so Lowes gave us the choice of machines and we decided to go with the Maytag Bravos. Lo and behold, were still getting holes in clothes. Several repairman told us the issue is common and is caused by the force of the water flowing into the machines plus the rapid spin cycle which pushes the clothes through the punched holes in the tub and the clothes catch on the metal on opposite side of the tub. Turns out sister-in-law had the same problem with her Duet and (not knowing I bought the Bravos and had the same issues) bought the Bravos and also is still getting holes. So I know its not just me.We also have problem with the machine not putting in enough water so clothes do not come out clean. In fact, a lot of stuff comes out with areas that havent even gotten wet during the wash cycle. I just want an old fashioned machine with an agitator that fills the machine fully, washes my clothes and doesnt put holes in them.

We bought this from our local big box retailer paying $433.87 after installation, the oven, haul away and home delivery. Two years and 3 months later its a boat anchor. Display is cold and dark after stating we needed to open and close the door before it would heat. We did but it kept displaying the same message. Unplugged it, turned circuit off per Maytag customer service line, still nothing. It is no longer made and you cant get parts. It is useless. The 10 year warranty just covers the magnet and the cavity.

I spoke to Destiny today at the Resolution Center, she knew one phrase, its a low usage washer. I would reply, 3 inches of water in a drum does not wash my familys clothes. Every load is covered in white soap specks, whether powder, liquid or pods are used. Again, Id hear, its a lower usage washer. Ok, I got it.The machine has been cleaned with Affresh.This washer cannot clean a single shirt let alone a full load of wash. Maytag (actually made by Whirlpool) should be ashamed to produce such a shoddy product and expect to the consumer to keep paying for repairs. From reading the reviews on a couple of websites, consumers have to keep repairing this washer time and time again. Destiny told me she would send a technician out at my expense. The machine will be in the landfill on Saturday. Never again Maytag/Whirlpool.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

Maytag Bravos 300 Electric Dryer - Purchased dryer 2011 and a computer part went out and Maytag wants $418.66 for a computer part. This dryer was used only 6 months a year. Poor attitude about repairing from Maytag and they would not do anything to make us happy with product. A dryer that goes out in 3 years is robbery. Maytag should repair and make customers happy but they just dont care. Anyone who buys a Maytag or Whirlpool product should have their heads examined. I tried to talk sense to Maytag representative but to no avail. I am now going to make sure all of southern Indiana knows of my problem with this product. Those who know me know I have the ability to contact thousands of southern Indiana and Louisville residents.

We have had our side by side Kenmore for years and it hasnt let us down! We eat mostly fresh food since we cook a lot and we always have plenty of space for our food. We are only a family of 2 though. They say the ice maker is the first to fail and it has not given us any issues for nearly 10 years now! Love Kenmore!

We had 10 year old Kenmore units in the past that were much better and worked faster at both cleaning and drying. We prefer a washer with a agitator and top load. The dryer is preferred to be gas. Both the Maytag washer and dryer we have need constant repairs. Washer for control panel repairs, and dryer for false heat sensing problems. Now they say not to use dryer anti-wrinkle sheets. The washer needs less sheets put in at a time to rinse better. It is a agitator less model.

I purchased a Quiet Series 300 E71195 dishwasher in 2011. Its about 3.5 yrs old. I guess misery loves company because like so many other complaints on this site my control board died, and Maytag, while saying they care about customer satisfaction, basically said tough luck pal, youre on your own. Sadly I own 3 other newish Maytag appliances. When will these appliances die without support from Maytag? Im not holding my breath. My next step is to complain to the dept of Consumer Affairs and create a page about nefarious Maytag on social media. Avoid the Maytag brand when shopping for appliances. I know I will.

Maytag Dishwasher Model MDB 7749SAM0 - Bought this dishwasher from Lowes in 2012 for my daughter and son-in-laws new home. Thought I was making a good choice with Maytag. Wrong. Same control board problem that everyone else is having. Wiring ribbon is corroded and shorted. Why is this not a re-call? I will call Maytag and Lowes and complain, but likely will get no justice. Sounds like I should just bring this machine to the dump and take my losses.

The Maytag washer is very quiet & economical by filling the amount of water needed per load so actually a money saver. Also got the huge drum to wash quilts & blankets. My old one lasted 10++ years. Hopefully get as many years out of the new one.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

We purchased a Maytag Dryer with the lint vent on top on March 21, 2014 from ABC Warehouse in Ann Arbor, MI. Whoever engineered this does not dry clothes. Trust me, this will be the last Maytag I buy. There is lint seeping out of the top and when you clean it the lint gets all over the place therefore, my laundry room is always full of dust.

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

Purchased 6-1/2 years ago when we had kitchen remodeled. Bought the stainless steel with stainless interior. The interior design was perfect for placing the various dishes, glassware and utensils. There are a number of settings to choose from, however, we tend to use it as more of a sanitizer so the light or normal wash are the preferred and dont use the heat-dry as we dont find it necessary. Very pleased with the quietness of the cycles and have no regrets with our purchase.

Our Maytag washer 4000 series was installed on September 2010. Within 12 months and 5 days, we are now waiting for our second spin bearing to be replaced. It is a repair that takes 2 guys and 2 hours, and they basically have to replace the guts of the machine. I can imagine this is, at minimum, a $500 repair. We didnt buy the extended warranty, but luckily, the appliance shop was able to talk Maytag into eating the cost since we were only 5 days out. With the purchase of our new house, we upgraded from our appliance allowance to this model. With everything going on with the new house and selling our old one, I didnt do my normal internet searches for customer reviews and that was a mistake!Maytag has since sent us a warranty extension offer for $350, covering 3 more years. I guess Ill be buying that. It sucks that you pay top dollar for a washer only to find out that you have to pay an extra 40% just to keep it running for 4 years. No more Maytags for me, ever. Note to Maytag, you sell junk and your business goes into the ground. You are selling junk! Stop trying to squeeze every penny out of design and build, or you wont have a job.

Part on fridge is defective. They have sent the part but tell me they dont have anyone in the area to work on it. Nor will they pay for someone to come out. We must replace it ourselves. This product should be on recall. Maytag fridge. Freezer door on bottom filling up with water. We have 2 of them doing this. One about 15 years old. Other one is 3 yrs old. Maytag knows of the problem but wont fix it. Wont recall their default product.

I suppose I am the lucky one in that the Maytag Bravos was given to me free. I took out a perfectly good Maytag standard agitator washing machine and replaced it with this several years old unit. What a mistake! I read the other reviews and see that I share the same problems. I always get a the oL fault as soon as it goes to do the final spin. So I have to reset and try again. Also I have seen the same kind of dirt on the clothing as others report. I dont know that I will waste my time contacting anyone about the fault code. I may just put the old one back in and scrap this thing!

Refrigerator - The freezer of the refrigerator would randomly leak on the floor. When I had it repaired on 12/30/14, at a cost of $253.97, the repairman showed me the defective part. He confirmed the online reports that the leaking was caused by a defective part. The defective part had been used because it was cheaper. Now the repaired refrigerator works well. Last month, the control panel on the dishwasher stopped working. According to the online reviews, this is a frequent problem requiring that a new control board be installed. The reported failure typically occurs after the one year warranty expires. My appliances are located in a second home so are only used about once a month. A salesperson at a different appliance store said that appliances usually last from 10 to 12 years. The four years of occasional use prior to failure is not acceptable. I would like to have Maytag repair the dishwasher at their cost. How do I get this to occur?

Ive had this Maytag for more than 15 years and it still works well. Its a basic fridge, no special features. Just keeps food cold or frozen. Freezer at top, fruit & veggie bins at bottom, cheese bin. No problems, good performance.

Purchased a Maytag Dishwasher (Model MDB7749SBBO), total with tax $590.34 on 3/31/13. It wasnt a cheaper model, had stainless interior. Owning it after a 1-1/2 year, the Control Panel went bad. Maytag offered me for $267 for repairs and 1 yr warranty. Why thats about half the price I paid. My personal repairman told me the cost would be around $200 to replace the control panel. Why I could get a more inexpensive model for $300 and still get a year warranty. Very disappointed in Maytag quality of their product.

IT A GOOD DISHWASHER, BUT I HAVE HAD 2 PROBLEMS WITH THE CONTROLS AND HAD THE CONTROL PANEL REPLACED. TWICE. The insurance I bought with the machine, sent me a jerk to fix it, I complained and they sent a good repairman.

Was assured the washer could do comforters, etc. Well, I took a video of the washer doing 5 t-shirt, 1 pair of pants, and 3 pairs of socks on the power wash cycle. Nothing tumbled. All the plate did was swish some water around on the bottom. Clothes werent clean at all. Check my Youtube video, and you can watch the leg of the pair of pants sticking up out of the water and never getting back down in to get wet. Horrible horrible machine. With that said, called the company I bought it from, and they arranged for a front loader since Id only had the machine for a couple hours. Stuck me for a second delivery fee though, which I wasnt happy about. Well see when the new one gets here Tuesday.

I purchased the washer and dryer approx 6 or 7 years ago. Out of the gate about a year the pump had to be replaced on the washer- 2010. 1/2012 the tub needed to be replaced, 6/2012 the PUMP needed to be replaced again! Then 2013 the dryer need a new board at the tune of $391.00. And today, yes - yet once again I need a new pump! Over $2,000 in repairs on these awful machines. I called Maytag because I thought maybe they would care - not so much. The rep told me that the Bravos models were discontinued (shocker) but that she could give me a discount on a new comparable version at ONLY $600. How nice! I will use these until they fail again - which according to history - that wont take long and then I will NEVER EVER EVER purchase a Maytag product again. We work hard for our money and continually giving it to a company (for parts) for a product that they failed to make a quality product is not going to happen again! DO NOT BUY MAYTAG. Do your research and give your money to companies that care. MAYTAG should be held accountable and a class action suit should be filed. They need to GET IT and they never will if we sit back and let them take advantage of consumers.

Purchased this washer at the end of August and it was delivered the first week of September. On September 27th the rubber seal around the door somehow got tangled in with a shirt and was ripped off (absolutely no idea how that even could have happened) and spilled water all over the floor. I called Maytag on Sept 27 and they had a tech out here by October 2nd which was great. However, even though I had told them the problem and that the rubber seal was damaged the tech didnt bring one when he came. I had to call them last week to find out what was going on - they had the tech call me and he said that the part had just shipped and he should have it by next week - Today, I had to call again as there was no follow-up from the tech and was told that hopefully the tech will come on October 21st once he gets the part as he hasnt received it yet. I regret purchasing Maytag, as I had heard they had better service (local techs/parts warehouses) than LG or Samsung but that doesnt appear to be the case. 3 Weeks to repair a $1400 washer that I used for about 4 weeks is unacceptable. On top of the inconvenience Ive had to spend $40+ dollars a week at a laundry mat, plus waste my time. One star service.

I purchased a Maytag dishwasher in 2013 and the control panel needed replaced within the warranty period. About a year later, the control panel started to malfunction again, this time out of warranty and Im told it will cost over $350 to repair. I paid a lot for this dishwasher and thought I would get years of use out of it. I plan on buying a new cheaper one (not Maytag) for a little more that the cost to repair the Maytag. Im very disappointed and will not purchase another Maytag. I also read online that Im not the only one experiencing this problem.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

Two years ago I purchased a Maytag commercial technology top-load washer. It only two options for water level, either deep water or Auto sensor. Because I live alone I have very small amounts of clothing to wash at a time. Therefore I was excited about the auto sense to save water. However when using the auto sensor theres such a small amount of water in the drum it does not cover the clothes being washed and often I have items of clothing come out of the wash cycle and rinse cycle with dry spots on them yet. The clothes dont get clean and begin to smell stale shortly after theyve been washed. I contacted the business from which I purchased the machine and they were not able nor willing to do anything about my dissatisfaction. This is the worst Appliance I have ever purchased in my 64 years hows life. I hate this washer. It is totally ineffective. And now Im stuck with it and dirty clothes.

Original owner of $800 HE top loader washer since 2010. We heard a grinding noise for months, then finally it seized up. Repairman quoted me $300 to replace bearings. The repair guy seemed a bit too eager for the job, so I knew it must have been easier than expected. I Googled the heck out of it, and used this forum heavily for guidance. Seems the bearing failure is a pattern issue. It also seemed ridiculously involved and no one had posted a how to video matching my model’s layout. I took a peek with my own eyes and noticed a sock had gotten under the basket. The sock got caught in the drive belt and knocked everything loose. I removed the debris, tightened the pulley and everything worked. Cost me $0 to fix myself. So buyers beware before repair. And check the error codes yourself when in doubt! The first thing I did was check error codes. Found a great video here **.

Maytag used to have a reputation for quality. Their low water energy efficient Centennial is a waste of money. Half of the time clothes come out wet and most of the time they are still dirty. Also you are only supposed fill the tub 1/4 of the way with clothes so you end up doing 3 times as many loads per week. What genius came up with this idea? Save your money. You would get better results washing your clothes in a tub with a washboard. Seriously!

I bought a Maytag washer, dryer, and a dishwasher from Home Depot. It has only been a year and 1/2 and the washer has already broken down. Maytag wont help and neither will Home Depot. We are two elderly ladies (sisters) that used it once or twice a week. I feel we got ripped off. We cannot afford parts, labor, or a new washer. This product needs to be pulled. And Home Depot should not sell anything that is not a better quality. I trusted both companies and am sorry I did. Thanks.

I have an MSD2542VEB01 model refrigerator purchased slightly over two years ago. I have the same problem as many others, which is the plastic breaking on the shelves. The first time, it was within a year and the part was under warranty. It is now a year and a half later and one is broken beyond use and another is cracking again. Maytag refuses to help me as there is no “recall and the plastic is not available separately from the easily removable glass of the shelf. The least expensive price that I can find for the shelf is $107 and I need two of them. $214 (plus shipping) when all I need is two pieces of plastic? Be very careful when selecting your appliances.

Bought a Maytag fridge model MFI2569YEM0 a few years ago. From the get-go, the ice machine would spit out ice hither and thither, mostly not into the cup or mug. Even when I held the cup up high into the dispenser orifice, I noticed it still spit out ice seconds after I released the cup, so ice cubes would spill onto the floor. Secondly, the vertical doors do not close well, and I must manually push them closed, especially the left door due to the poor design. (I noticed my neighbors more updated fridge has a better closing door. Forgot what brand, though.) Theres also rust forming on the front of the stainless steel fridge panel. It has penetrated through so I am unable to remove it.Lastly, this past week I walked into the kitchen stepping in a pool of water in front of the fridge. There was a sheet of ice accumulated on the bottom of the freezer. After some research, its likely the nipple in the back of the fridge that plugged up. I have yet to fix the problem, but so far, Maytag gets an F- in quality, and I will NEVER, EVER purchase any of their appliances again. I remember my parents washer dryer lasting 30+ years. Maytag, what happened???!!!

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

We purchased a brand new Maytag washer dryer and had nothing but problems with both. After talking with corporate several times, trying to reach the CEO, the customer service person told us that the problems were buyers remorse. Needless to say we will never purchase another Maytag/Whirlpool product as long as we live. We are going with Electrolux!

Worst brand ever. They both broke at the same time. Spend too much money. Never buying these brand again. Maytag sucks. Dont buy Maytag washers or dryers.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.