Washer is noisy and water does not saturate clothes on normal wash. Have to use sheet setting for small or large load. Washer changes gears and it is so loud and clanks like something is falling apart.

MBD7709AWB2 - Bottom line, every 1.5 years (18 months) you will have to buy a control panel. Number 3 for me cost me $149.00. Now my wash cycle will not kick on. Do I have to tell you what dishwasher not to buy!

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

I spoke to Destiny today at the Resolution Center, she knew one phrase, its a low usage washer. I would reply, 3 inches of water in a drum does not wash my familys clothes. Every load is covered in white soap specks, whether powder, liquid or pods are used. Again, Id hear, its a lower usage washer. Ok, I got it.The machine has been cleaned with Affresh.This washer cannot clean a single shirt let alone a full load of wash. Maytag (actually made by Whirlpool) should be ashamed to produce such a shoddy product and expect to the consumer to keep paying for repairs. From reading the reviews on a couple of websites, consumers have to keep repairing this washer time and time again. Destiny told me she would send a technician out at my expense. The machine will be in the landfill on Saturday. Never again Maytag/Whirlpool.

First off. Maytag customer service is horrible. I purchased a Maytag washer & used it 8 time. It now doesnt rinse the soap out of my clothing or even clean anything. The washer isnt broken because thousands of other people with the same exact washer have written negative reviews everywhere online. The washer needs to be recalled & never sold again. Maytag is making people SICK and they dont care. My whole family had skin irritation because we didnt realize our new washer wasnt rinsing.

My mother always said Maytags were the best but I never bought a washer and dryer until about 5 years ago and both are the worst appliances I have ever owned. The washer has rust all over the bleach container and smells to high heaven and I clean it with Affresh all the time. The dryer doesnt dry well and the washer doesnt wash well. I am trashing both and buying some new ones.

Do NOT buy a Magtag washer. I purchased a brand new washer from Lowes in 2017. The washer gets stuck in the wash cycle. When I called Lowes, they said to call Maytag, who sent a service person out. The service person recalibrated the machine never ran a cycle and left. We had to call two more times after this for the same reason with the same result where the serviceman left without running a cycle. This was all while the product was under warranty. Since I had three service calls, I called Maytag frustrated that this kept happening to a new product. I was told there was nothing they could do, but if it happens again to have the service guy come back out. When the warranty runs out, I will have to pay for the service tech. Unbelievable. Save your time, money and frustration and buy a Whirlpool! I dont know how Maytag gets away with selling defective products.

After buying this dishwasher model MDB6759WWW3 in Jan. 2010, I fully expected it to work longer than it did! So far, the control panel has been replaced 5 times. The last time was Sept. 17, 2012 and already it is out again. I talked with Customer Service, since Georgia has a lemon law. After 4 times it is to be replaced.They had no record of the part that was replaced, just that a technician had come and repaired (by ordering the same part they had no knowledge of). This time they will either replace or instead of me calling, my lawyer will call. I will never buy another Maytag product and will encourage anyone else not to buy either. My daughter had the same experience with a refrigerator, a piece of junk they did nothing about. By the way, I have an extended warranty plan, which should not even be necessary!

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

We purchased a Maytag Front Load Washer in April 2011. We did not purchase an extended warranty. From the beginning, it didnt seem to clean as well as our 12 year old top load Whirlpool had. Then in Summer 2013 it began to create fabric pulls in fine fabrics - tablecloths, blouses, etc. Whirlpool sent a repairman who charged $90 to tell us that the drum needed to be replaced because of a rough spot. He ordered a new drum and we understood that it would be replaced because it was within the 5 year manufacturers warranty on drums, but we would have to pay for installation. 2 months later, Whirlpool informed us they could not supply the new drum. Why are replacement parts not available for a 2 year old machine? The customer service rep told me that they would replace the machine for 15 percent of the cost of a new machine. All I needed to do would be to pick out a machine and let customer service know the model number and they would make arrangements and contact me re: payment of the 15%. When I contacted them again I was told that I would be expected to pay $508.00. That is 15% of a $3000.00 machine. It it completely unfair. Later, I was told that the first rep I spoke to must have been wrong because they dont pro rate replacements on a percentage basis. I told them that I was not interested and they have lost a good Whirlpool customer. In the last 15 years we have purchased 7 appliances made by Whirlpool. Never again! I am not impressed by their customer service.

I wish I had read the reviews before selecting this Bravos XL washing machine. I bought these from Conns Appliance as they were on sale 750. Rounded figure... They were delivered today and the company was professional and set them up, I have spent the last 4 hours washing the same medium load of childrens clothes trying to get them clean. Ive even separated them into smaller loads and am now into the 5th hour of laundering this same load... Im returning them but its gonna cost me 15% restocking fee. If theres a class action please count me in. I thought because our Maytag Neptune lasted so long wed have a great outcome again with these, boy were we WRONG!

Why are the clothes in my dryer getting stuck in Maytag Neptune? It seems there is a little opening around the rim of the barrel in the back of my dryer that drawstrings, zippers or similar small parts of the clothes can get stuck in. It twists the clothes around and is ruining clothes, also is making a thump-thump sound. Someone, please help!

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

We purchased this Maytag washer. My wife liked it at first, but after a few months she kept complaining the wash stinks, and I can also say that. I complained to my wife about the smell of our wash, especially the wash towels. The wash was turning colors and some we threw away. My wife has been complaining about all this for months and years and said she will never buy another washer like this. Then about two years ago, she was having trouble with codes coming up. We called service, but didnt get any help, so I looked on internet and found the problem with the code. I took the washer apart and cleaned the tube out and the washer worked, but every now and then my wife needs to climb over washer and unplug, let sit, then replug back in and start it to get rid of code. My wife and I are very upset with this washer!

I bought Maytag washer 15 months ago and the washer is now leaking from the bottom. My floor was damaged from the leakages. I have not use the washer much in the past 14 month because its just me in the household. I will never buy a Maytag product.

Our Maytag Dishwasher, Model MDB4949SDE2 was purchased May 14, 2016 at Home Depot for $470. It has performed perfectly until January 6, 2020, when a noise, loud enough to imitate grinding wheel, happened with every Start-Up attempt. An independent technician advised replacing the pump motor, thinking that perhaps some popcorn kernels had lodged in the system. (Kernels were cleaned out of the drain filter.)We operated the unit after he left, and the noise began to diminish, eventually disappearing altogether after several loads. Today, February 26, 2020, the same tech found that the large, upper impeller was clogged (not rinsing completely) with citrus seeds and VARIOUS METAL SHAVINGS & SMALL PIECES OF WHAT WOULD BE CHOPPER BLADES FROM THE INTERNAL GARBAGE DISPOSAL. After reading the Maytag Dishwasher problems experienced by others (with repeated control panel failure, burning wires, leaks, and house fires), I consider us lucky to have none of those. We will not run the unit at night, nor with an empty house. Next problem, we will buy a Chinese made dishwasher, like GE.

MMV5207BAQ purchased in Feb 2009. I paid $512.00. 5-09 Bob Millers Appliance replaced the door because it bubbled. 10-11 Bob Miller appliance replace the door because the handle broke off. 3-12 Bob Miller appliance replace the door because the handle broke off. 10-16 Door handle broke off again under normal wear and tear. 12/14/16 I went to Bob Millers Appliances and was told to contact Whirlpool. 12/16/16 I called Whirlpool, Tina said, yes it is excessive but it is not under warranty and they do not make the microwave any longer and they cant do anything to repair it and they can not fix the issue. I find it how to believe Im the only person who has had this issue. I dont have kids. Its only me that uses it.

My clothes come out extremely wrinkled and start piling after a couple of washes. I wash on cold and do not overload the machine. I am 64 years old and had always loved Maytag until I got this set 4 years ago.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

I have the model with a smaller oven on top. I use it about 98% of the time so Im not wasting energy having to heat a larger oven space. I also like the fact that I can clean one oven. The larger oven is used when I cook turkeys. I can cook many dishes at a time, by using the smaller oven for dressing or cakes.

I bought the Maytag Bravos X washer and dryer combo 4 months ago and its been a hassle every time I use the washer. The dryer is fine, but the washer constantly has problems. No error codes, I just hit start and it clicks intermittently in sensing mode for 10 minutes and shuts off. Once in a while, it decides to work - adding water, but never cleaning thoroughly and I always have to run an extra spin cycle because the clothes are sopping wet once it finishes. Ive been reading reviews all over the internet describing similar issues with these models and I am kicking myself for allowing myself to be convinced Maytag is a quality brand. Dont waste your money on these pieces of junk and really do your homework. I wish I had never bought them and am angry that I will have to deal with it until it eventually breaks down in the very near future, Im sure.

Currently own model MTB1504ARW, serial number 12541413GT refrigerator. The defrost thermostat broke and it is causing the device to frost over and not cool. Maytag is trying to replace the part with part number 63001051 and that part does not match the part that came with the machine. I spoke with a supervisor, Mr. ** who certainly was not a problem solver or any help, in other words, lacks customer service. I explained the installation of the wrong part may be dangerous and could cause a potential fire or hazard. He assured me this was the part available, but also said it was discontinued and I would have to find it with an outside vendor. I explained I compared the part removed and the part they are suggestion, per the part list, and its the wrong part. As a supervisor, Mr. ** failed to provide true customer service for myself and future customers who may be in the same situation, with the potential of causing a hazard for customers. The Maytag supervisor should learn to provide customer service and prevent possible hazards for customers, taking the next necessary steps or research the issue with other departments within Maytag. The parts below are evidence of the issue, the suggested part has two wires, the one from the refrigerator has three... poor customer service, at best with potential hazards to families and children. It may because their appliances dont break, according to their commercials, they just have too much time on their hands and cant provide the assistance that is needed.

WARNING FIRE/HEALTH HAZARD - BRAVOS MVWX500XW1. Purchased it new 2011. Never cleaned well. Some clothes came out with dry spots, darks had soap scum/lint spots over them. On several occasions, clothes were not wrung out properly. BUT when I went to do a load of laundry recently, I heard a loud POP and almost instantly my entire basement filled with an acrid, dense grey smoke coming from under the machine. I am concerned toxic chemicals were released. People still smell the odor in the house. Need to get in touch with company again after the weekend to see what they will suggest.

I bought a Maytag microwave in Feb of 16. Six months later, last August, it stopped working correctly (light doesnt come on, will not start, continually says open/close door to start). I have been trying for THREE MONTHS to have this fixed. Multiple calls to Maytag have resulted in nothing but empty promises. Calls to the store where we purchased it do no good - you have to call Maytag. We got 6 months use out of a Maytag microwave which we paid EXTRA to have installed. At this point I dont want it fixed. I want it replaced. The Maytag brand used to stand for durability and integrity; now it stands for badly made products and pathetic customer service. Look up my phone number on your computers, Maytag, and you will see all the efforts Ive made to get this fixed.

Hi we bought Maytag washer & dryer from Lowes last year. Since then it burned every single fabric silk to cotton, tops, pants and sheets to comforters even on delicate setting, costed me thousands of dollars. We are totally wasted our time and money by buying this product. I would never recommend to anyone. It’s disappointing and pathetic to see how they even pass the quality testing before they release to the consumers. All my brand new clothes and comforters one wash and they are ???? burned. Not even one star worth my time. I cant wait to get it replaced ASAP. I have pics to provide. Totally dissatisfied with this dryer. Washing machine is two star only compared to other brands.

I bought a Maytag dishwasher from Home Depot August 2018 and it has leaked soapy water every 3 out of 5 times that I run it. Home Depot said they dont cover installs after 2 weeks and to directly contact the manufacturer for service. Maytag sent out a tech 3 times but they werent able to replicate the problem, so nothing has been done to fix the dishwasher even though Ive shown the tech different photos of the dishwasher leaking. The service tech said they will now charge me $90 to return, even though the dishwasher is still under warranty and not repaired! Ive owned many different dishwashers (rentals and houses) without any problems. This is the first Maytag brand and it is horrible. I will never buy another Maytag and have warned all of my friends and family.

Purchase date of Maytag dishwasher 12/9/11 for $651.37. Controls broke 6/2013. Used Maytag specified repair service at cost of $450. New control panel installed 7/9/13. Control panel broke again 8/13/14. WILL BUY NEW DISHWASHER. NOT MAYTAG.

This washing machine is good for cleaning clean clothes, like stuff you wear one day at a desk job. But nothing dirty. Its really bad. Dont fill it either, nothing will get clean. 1/2 full or less. If you put too much clothing in there it will leave lint and other debris all over them. Also, dont use granular detergent, it wont dissolve or rinse out. Liquid detergent only. Weve had it for about two years, and its a constant disappointment. A total waste of money. Really annoying. I have to get rid of it. Its almost completely useless.

Bravos XL - This machine purchased in 2014 at Home Depot service plan, needed major repairs just over a year old. Tech working on this machine replaced the whole tub assy after Maytag want to just do the cheap repair and just do a bearing kit. Reading online all the hundreds and hundreds of the same complains Maytag has done nothing in good faith to replace these junk washers!! My washer is now leaking under the washer less than a year after the last repair!! My good friend purchased the same machine and has had the same issues and his has been down for weeks because the poor service person from Maytag service broke some of the new parts! Now the washer is leaking again. WHAT can be done. This not right!!! Public needs to be warned about these flawed machines and Home Depot is still promoting these Junk machines!!!

Should have researched before purchasing our Maytag Bravos MCT washer! We purchased it at Home Depot and it was delivered and installed by a certified technician. From day one it has been so loud and obnoxious with the way it “knocks” and “clicks” when it runs through a cycle. When it spins the whole machine shakes viciously, despite being balanced properly at installation.We have owned this washer just short of two years and for the last 8 months we have had to keep unplugging it to reset it so that it will even run through one cycle. The most recent two months have been extremely frustrating, due to the fact that not even troubleshooting can aid in “fixing” the fact that this piece of crap washer will not complete a wash cycle! It either stays in sensing mode & doesn’t add water, or it adds water but doesn’t do anything but sit still for about 15 minutes and then drains all the water back out and stays stuck on “wash”. We are researching online and have found many similar complaints with the same negative experiences. Our next step will be to call a repair person! What a crock!!! Maytag gets a big “thumbs down” from us!!!!

I bought a Maytag Dishwasher. The control panel has been replaced 7 times! About the protection plan that I renewed every year, the representative said that in order to replace a lemon, it had to break down 3 times in one protection plan year/12 months.

In 2003, I purchased a brand new Maytag washer and dryer set, I chose Maytag because of their reputation. Within the first 6 months, I had a bearing go bad on it and that had to be fixed. It has become noisier and noisier throughout the years and now it is leaking all over the floor when I do a load. I am single, I live alone, I do laundry very seldom and do not do large loads. I am so disappointed with Maytag. When the repairman came out initially to fix it, he said that the brand he fixes most often is Maytag. Expensive lesson learned, Ill never buy any type of Maytag product again.

Product: Maytag MFI2665XEM Ice2O 25.5. Bought this refrigerator on Feb. 2013 at Home Depot. Maytag cannot repair the heat exchanger as it is a discontinued model. Our only option: Purchase another comparable current model refrigerator with a full price of $2,199.00. It will be sold to us for a discount price of $1,308.00 with free delivery. NJ tax and installation not included. This is a two year old refrigerator with orig over $2000. We had requested for a repair since August 2015. We had spoiled food expenses and rented a temporary refrigerator. Numerous attempts to repair and order the parts to no avail. The excuse is either they ordered the wrong part and eventually was told its been discontinued. Our warranty was automatically canceled. We have spent numerous hours with the Maytag customer service and was given a promise to find the part overseas as well to get the appliance fixed. Finally, this morning of November 2, 2015, we were given the final Im sorry and this is all we can offer you, to buy another refrigerator from us. It appears that this is a defective model but we have not received any recall letters or warning about it. This needs to be addressed as this is an unacceptable practice and deceiving to the consumers, and certainly unfair for people like us who work very hard to pay for this appliances. We cannot afford another $1500 refrigerator. We are now stuck with this worthless, stainless steel junk in our kitchen.

I purchased it 8 months ago. I have had problems with the machine leaving clothes soaked at the end of cycle. I have contacted Maytag (still under warranty) and they replaced the motor. The first load after repair still had the same problem. They said the check drain was not clogged. The snaked drain has no backups. After every wash, I have to reset the cycle to drain and spin. The machine spins for seconds and fills back up with water and doesnt spin again, but does drain. Clothes are sopping wet at the end of cycle. I contacted Maytag. They said I could be billed for customer education ($129) if they find no problem (threat). I want my money for purchase returned or at least 3/4ths. I expected my new machine to last years, not months.

Model MDB7749SBM1, Complete FALSE ADVERTISEMENT and GARBAGE. Let me explain. Maytag clearly claims this dishwasher is stainless steel on the inside and out... FALSE, BOGUS CLAIM. Please check for yourself, tried a magnet to it everywhere and the magnet stuck everywhere. I have had this dishwasher for 15 months. The keypad frequently stuck. When I called Maytag, they told me if its usable, there is no defect. 15 months after purchase and 3 months after WARRANTY ran OUT on Thanksgiving Day with 25 guest. The keypad finally quit for good. I called the Friday afterward and was told no service for a week. I called and received local service but they told me it would need a keypad, which I waited to call on Monday since Maytag is closed on weekends how ironic. I was told they wont cover anything since a certified person didnt come out even though nothing was ever fixed and they blatantly lied to the consumer. Tried to sell me an extended service plan. I will NEVER BUY ANOTHER MAYTAG PRODUCT AS LONG AS I LIVE AND WHEN IM IN LOWES OR HOME DEPOT, I WILL TELL EVERYONE IN THERE SHOPPING THE SAME THING, DONT BUY MAYTAG IF YOU KNOW WHATS GOOD FOR YOU.

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

Our Maytag lint trap started falling apart a few months after we received it. Call Customer Service to get a replacement due to the product being faulty. The answer that I got from Customer Service: We sell you a new one. Poor customer service, faulty product. Dont buy dryer from Maytag.

I purchased My Maytag Washer and Dryer set from Lowe's, which was a very good experience all the way, back in June 2017. After two years I can finally give an honest review. We love this set even though it is not as quiet as the old Maytag washers. Still is but not as. We have not had one bit of trouble from either the washer or dryer. The next size larger would have been the better choice for us since we now have king size bedspreads to wash. It still does the job though, just one piece at a time. A lot of people complain about the smaller amount of water used but it still cleans clothes quite well. If you need more water just use deep water wash or for even more water use the setting for bulky sheets which really fills up the water level.

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

I wrecked on a bike, had surgery and in a wheelchair. I bought and had a Maytag dishwasher delivered from Beaumont Home Depot and this mdb7749sbw2 model never never worked. Home Depot told me I had to bring it back myself (Im in a wheelchair at the months that was impossible) and I called Maytag warranty. They sent a tech. He replaced a front power panel that didnt work. They sent out two more techs and they said use other soap Lemi Shine and the other guy said use Finish and turn your hot water heater all the way up. That never worked either. I have had this a yr and it just sit there and money in the trash. It makes me sick.

Purchased my Maytag range/oven 14 years ago and it still works to this day. I had to replace both oven heating elements. I am a do it yourselfer, took me less than 5min to replace both. The cook top is easy to clean. As long as you take care of it, it should last you a long time.

Purchased washer in 2015, worked pretty good for 4 years. In 2019 belt, support rods, and control board replaced. In 2020 clutch, pulleys, and suspension replaced, waiting for service technician to replace transmission later this week. I purchased extended warranty thru Lowes, glad I did as the machine literally jumps in the air during spin cycle. Lowes stated I needed 4 repair visits to place a claim for replacement! Machine will not spin properly on high speed. Luckily I have a spare machine in the garage to use while I waited for repairs to be made. However, nothing seems to be correcting the problem. Very disappointed in the Maytag washer.

Bought a Maytag washer from Lowes 3 years ago and it is just junk. I am 62 years old and never had a washer that actually broke down. What happened to good American technologies. I guess those days are gone, anyway dont buy a Maytag, duh. It is the day after x-mas and I have to buy another machine.

We purchased our Maytag Elite dryer almost a year ago. Began to have problems with it several weeks ago. We first tried to correct the problem through the store where we purchased it. After three failed service repair visits the technician recommended we call Maytag directly. We did. Another service appointment was set up. The repair guy determined there was nothing wrong with our dryer (?? It wasnt drying on one of the heat settings!!) but said he would come back and replace the front sensors anyway. After he left I called Maytag again. Explained why I was frustrated. I was told that since the repair guy said nothing was wrong with the dryer there was nothing further they could do for me. Further attempts at repair had to be at my expense. I was incredulous to say the least. The dryer doesnt function properly on the normal heat setting, but because the repair guy cant find the cause I am therefore just out of luck?I will never, ever purchase another Maytag product. I am shocked that they will not stand behind a product that is still under warranty. After only 11 months of use I am stuck with a dryer that will only dry on high heat?! How can a single service visit by their repair guy (whom is on their payroll) be the final say? No second opinion? Is he infallible? Simply unbelievable.

Please Do NOT purchase the Maytag Aqua Lift Gas Range. It does not clean anything, you will pay more money for a cleaning oven that does not clean any grease or droppings if you cook. This is not an Oven for any one, or family that cooks large meals or has gatherings. I had the technicians at my house over 4 times and they confirmed that this oven is not a self cleaning oven. It doesnt get hot enough as your self cleaning ovens. And MAYTAG did not want to hear anything, basically not clean much, but advertised as a self cleaning oven. Having been a Maytag customer for years I will never buy a Maytag product again. And we need to support American made, but not when the consumer is misled.

I purchased a Maytag model # MRT 18 FFFHO1 refrigerator from Home Depot. After 7 months, it stopped cooling (wouldnt cool below 52 degrees). Fortunately, I had taken out a 5-year extended warranty. Thats the good news. The bad news is that after numerous trips by a certified repair man -- and three spring/summer months without reliable refrigeration -- Home Depot promised a refund. Well see.Bottom line: keep looking for a refrigerator that works. I have tried GE, Frigidaire, Maytag and Sanyo. Since many of these companies are really just one inept cooperation with more names than Frank Abagnale (Catch Me If You Can), let the buyer beware! I would give Home Depot protection plan 5 stars, though. They stayed with me through thick and thin: by emails, phone calls and text messages. However, their protection plan is worth more than Home Depots appliance products -- through no fault of theirs.

This machine (Maytag Bravos XL) was in our new house and is relatively new. It is the worse machine I have ever owned. I am 58 and cant reach the bottom of the tub to get clothes out. It doesnt fill with enough water to clean the clothes, and repeatedly I have my clothes coming out dirty. I have had to rewash clothes to get them clean at all. Or they come out with grime all over them. I had both a LG and Samsung front loaders in the past, if I could afford it I would throw this Maytag out on the curb! Its a piece of junk.

Weve had 2 Maytag washers that lasted a combined 41 years. Five years ago we purchased a Bravos XL top load washing machine directly from Whirlpool. Like many other reviews, it is impossible to keep the machine from going out of balance and trying to tear the laundry room apart. I called Maytag and of course they want to make sure the machine is level in at least 3 dimensional space as well as 2 parallel dimensions per String Theory. As far as the 3 dimensions, I assured them I had already thought of this (as an aside, ever try to find any flat metal on one of these machines? Kind of helps when using a level.)So after more exciting conversation, they offered me a Warranty for $437. While trying to control my laughter, I said I could trash the Bravos and buy a new machine for that price. As far as repairing it, it cost $120 for a repairman to grace my door step plus $35 every 15 minutes plus parts -- again, the decision is to trash it and buy a new machine. In case I was too subtle in my comments, I WILL NEVER BUY A WHIRLPOOL PRODUCT AGAIN. Im too frustrated to tell you about my KitchenAid fridge. As much as I detest it, I am forced to join the buy and trash 5 year club . Sometimes the good old days were really better.

Ive owned the stainless steel version of the Maytag dishwasher model MDB7749SBM purchased on Sept 6th 2013. July of 2014, my first control panel went out. Lights not responding. Was within the 1 year warranty period. Now, that panel is acting up again. I called Platinum Factory service and they wanted to charge me for a new panel and the labor. Well, I used a few choice words on how I felt and the customer service person said the part would be free. Well, nothings free as I scheduled a visit by the Platinum Factory Service. They of course call 5 times to make sure you are home. The day of the service, the tech calls me to see if Im home. I of course said I am... then, he goes to tell me the labor charge for him to come out and hourly rate will come to $189!!! I said screw it and dont bother. Maytags quality and engineering SUCK. Avoid them...

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

I have a Maytag front load washer, and it has been flashing codes since day one, smells like mold, does not spin water out, and at first, all Maytag could say is, Im using too much soap, the wrong soap, loading too full, and I have it on a stand that is sold with the washer that they dont recommend, after I paid $300.00 for it. Now, it is flashing an E3 code, and will not finish a cycle at all. Maytag wants money to fix the problem that thousands of consumers have, after paying over $1,000 for the machine. I will never purchase another Maytag product, for as long as I live.

I purchased a Maytag Neptune Washer and Dryer at Home Depot for over $900. Within months, the board went out. The repairman said that they didnt even know how to fix it yet - no training. The board was out again. This time, it was not under warranty. The repair costs $779 including part and labor. There were numerous other little problems along the way that we did repair, but now, forget it.

Yesterday I was using my washer (small load of clothes), I was with my baby in the laundry room when suddenly there was a horrible noise and the door of the washer opened, he hit my back, something fatal could have happened. I do not know how it happened but a piece of concrete was inside the drum. I do not want to imagine what would have happened if that piece came out and hurt my baby. I spoke to the company and explained what had happened to me, but they do not want to be responsible for what happened because the washer is in Tijuana (border with San Diego), I bought the washer in Pirch San Diego California in 2015. Maytag United States is responsible for this defect. Dont buy this model:mhw8100dc extra large capacity washer with steam and powerwash® system-4.5 cu. Ft.

I bought my Maytag dishwasher MDB7749SBM0 three years ago. After it was in one month it already needed a service call. It needed a control panel. Out of the dishwasher 4 weeks because this happened over Thanksgiving. Two months later it stopped working and needed another service call. Technician was inexperienced and another one had to be called. Out of the dishwasher 3 weeks. At this time, and because of the expense of the machine, I purchased an extended warranty. This was control panel number two. Not long after, the heating element had to be replaced. Two weeks without the dishwasher. Now, my dishwasher stopped working again and it needs a new control panel. The technician is rude but did offer the information that the moisture ruins the control panels. IT IS A DISHWASHER!!! IT USES WATER!!! I only run the dishwasher twice per week so I cant imagine how poorly it would hold up if it was run more often. I am on my third week without the dishwasher because the part is on back-order! No one can tell us when it will be in. I bought a Maytag because I thought they had the appliance market under control. MY MISTAKE! I am very angry.

I purchased my Maytag Neptune pair on Jan. 24, 2005. I was unaware of the problems and lawsuit related to these items. Luckily, I didnt have any problems with them until May of this year. At that time, I spent $337.00 for a new control panel for the dryer. (Just because I didnt want to split up my set.) I expected them to last me for the rest of my life. Of course, the washer had started to do something even the repair man had never heard of before, right about the same time. I told him that the tub would fill up with gallons of water, and surprise me when I opened the door on various occasions, flooding my laundry room and the basement downstairs. Mind you, this would occur even with the water supply cut off to the machine, no hot or cold running to it.He performed a diagnostic test on it and said everything showed up fine. Of course, it didnt overflow while he was here. He is the one who told me about all the trouble and the lawsuits. I had wondered why I didnt see them for sale anymore. I have been keeping the water turned off except when I need to use it after all this time. It still happens! The repairman thought I was senile or something. I dont have a mold problem, no trouble with the door lock (yet), and out of all the comments and complaints Ive read online today, only this site had one with a problem of it flooding the house. My husband and I are on a fixed income, and here is this unit (that I thought would be my last) rotting out my floor and wall in the laundry room, and flooding my basement. Not to mention it rusting out the inside of the washer and its pedestal. I would like to hear from anyone else who had this water problem, and what it took to fix it.

The only complaint is the lights on the bottom quit working about a month after we purchased. It was nice to light up the stovetop when cooking. Now it’s slightly dark. I have gotten used to this. We spent about $8000 on all the matching Maytag appliances we purchased. I would love to replace all but not in the budget. I am a dissatisfied Maytag customer.

I dislike Sears and more so Maytag. I bought a Maytag Bravo XL MCT. It worked nice with very few hiccups until 1 1/2 years old. Then the washer went to the lock and done mode, thought it might be the lid switch down the washer up. Looks like I would need to change out the whole panel. Its not worth the trouble OR time to put one dollar to repair the piece of **.

I bought my Maytag Bravos top load washer from Home Depot. In one year. I had the Maytag warranty people out three or four times. The warranty ran out and I purchased an extended warranty from A&E. I have had them out at least five times.I called Maytag and they told me since that I didn’t get the extended warranty from them, that there was nothing they could do for me. I explained to them that this washer cost me over $900 and that I have had numerous repairs on the washer, in which the warranties cost me over $400 so far.How much do I have to keep paying for this lemon? Maytag will not do anything about it! This goes to show you that paying top dollar for a washer does not guarantee you will have a good product. In this economy we can’t afford for this to happen. This is a very bad product and Maytag will not stand behind their own products, but they are willing to charge the consumer high dollar for them. This is a disgrace!

We purchased a Maytag refrigerator (MBF2258XEW) less than 6 weeks ago, and the compressor has already failed! Its not good, but the reason I am writing is their customer service (or lack of it)! We were told that it would take 3 weeks to get the replacement part, which was only 45 days old. Home Depot, where I had bought it, has been great; and they pushed Maytag/Whirlpool to agree to replace it. But Home Depot cannot not get us a new one until the paperwork comes from Maytag. We were told by their customer service that it would take 4 working days just to process the paperwork! Thats working days, and this is a Friday! So now, theyve all left for the weekend, and I still have no refrigerator and no idea when I will get one! They said no to getting the part faster, no to speeding up the paperwork, no to me returning it and getting a refund, and no to providing me with a rental. Please consider this when making any new appliance purchase.

I purchased a Maytag Bravos 5 months ago. I had trouble at first with unbalanced loads. The repair man came to look at it twice. One thing that can unbalance your loads is if small pieces of laundry such as a sock gets outside the basket. Sometimes the basket has to be taken all the way out because small pieces can be lodged under the basket. This happens when you fill the machine too full and those small pieces float to the top.The suspension on my machine ended up needing to be replaced. I have read lots of reviews about soap rings in the clothes. That happens from using too much soap. Make sure you are using HE detergent for one. I cut way back on my soap and my laundry gets clean and no problems with residual soap on my clothes. I was very unhappy with my machine at first but now I absolutely love it!

I purchased a small (14.5 cubic feet) refrigerator for my basement from Home Depot on January 26, 2013. It was delivered on January 30, 2013. On February 14, 2013, we found that it was not cooling like it was supposed to. The soft drinks in it were not cold. I called Home Depot and was told I had to call Maytag for a repairman to come out. Since it was so new, I felt it should be replaced. They disagree. The warranty only calls for repair. So a repairman came out on Feb. 19th. He said that it has no freon. He doesnt know why. It could have a leak. It could have leaked out in the warehouse. There is no way to know this. He said another repairman would be out to fix it on the 20th. On the 20th, no one showed up or called. I called the repair company, S & S Appliance of Bessemer. I was told the repairman that I needed is in Montgomery today and the repairman yesterday was told to tell me he would call me. He was told to not tell me someone would be out today. So now, I have to wait until tomorrow for someone else to call me and see when he can fit me in his schedule. I think Maytag has a problem with their refrigerators. I think Home Depot has a problem not standing behind what they sell. I think S & S has a problem with their servicemen. I am not happy with any of these companies and will never buy another Maytag refrigerator or washer, but thats another story.

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

I purchased our Maytag dishwasher last November. Last week, the control panel went out. I called customer service and they were actually polite and helpful, except for the fact that I had to wait an entire week to have a technician come to my house. Being that I live in the Balt/DC Metro area, I would have thought they would have enough people in the area to come over faster. Anyhow, we finally had the technician come today and tell us that the control panel needs replaced and that he highly recommends an extended warranty, which costs $200 for 5 years. He let my husband know that the repair itself would cost $500 if not covered by warranty!!! What a ripoff! I purchased this dishwasher because I grew up believing in the Maytag brand. Sounds like this is an extremely common issue and if Maytag wants to make things right, they should discontinue sale of their crap product and provide those of us who are stuck with it, a complimentary 5 year warranty. I shouldnt have to pay $200 in extended warranty to make up for the fact that my control panel is likely to go out again in another year, when Ill be forced to buy a new dishwasher.

Worst experience of my life!!!! Don’t buy a Maytag washer!!! It’s agitating our clothes dry. Putting holes in clothes. We bought a warranty that’s pretty much useless. They will not replace. Only fix parts.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

We purchased the washer and dryer set from Lowes about 5 years ago, and purchased the extended warranty fortunately for us. We had good luck with the washer for about 6 months, then we had to call problem service out because the washer filled with water but wouldnt do anything else. It took several days for the service people to come out and when they did, they had to order parts to do the repair, so we did not have a washer for a few days or a week. They got the washer fixed and everything was good for a few months, then our dryer quit working. We were told that the tub of the dryer had come off, so they had to order another one. So we were again without a dryer. Once they got the parts in the repair company that was sent out to fix our dryer, did not fix the dryer correctly so we had to call Lowes repair service to send someone out again. We have owned this set for over 4 years and once again our dyer has gone out. During all of this time, I and my Brother had to leave our job in order to be home and meet the maintenance people to fix both washer and dryer. I would not recommend this set to anyone, this is one of the worst sets that I have owned. I thought Maytag was a brand that you never had problems with, but we have had nothing but problems with this set.

My dishwasher is two years old and it just stopped working. I called the store I purchased it from and they sent out a repair man. He told me that the control panel was damaged and that he would have to replace it. The cost is $145.00 plus the $50.00 service call. He said something must have spilled and got into the control panel. It is a built-in dishwasher underneath a kitchen counter. I think it should somehow be protected against spills and/or moisture getting into the control panel as it is underneath the kitchen counter. I do not remember spilling anything that ran down the front on the dishwasher. But even if something spilled, if it was made properly it should still be working. I will not recommend a Maytag to anyone and will also spread the word about what happened. Unhappy in Pennsylvania.

We have a Maytag Dishwasher Model MDBTT60AWB purchased from Lowes about 8 or 9 years ago. This model was included in the huge 2010 recall of 1.7 million units due to the possibility of heater-unit fires. For the last couple of years, its had a problem staying on the selected cycle: After being started on normal wash, it reverted to rinse only after a few seconds, but eventually quit responded to the selection of other cycles altogether. Removing the back from the door to expose the innards revealed the ribbon cable that connects the circuit-board head to the control panel had worked loose. Reattaching it provides a temporary fix, but it eventually works loose again. We suppose the screw holding the back to the door will strip sooner or later, but by then well probably be so fed-up with fixing it that buying a new (non-Maytag) one wont seem like a bad option.

I purchased top of the line Maytag washer and dryer in 1975! They are Harvest Gold. They were sold last week along with my house. I now have Whirlpool appliances in the rental apartment I moved to. There are some irritating features.

Bought washer in 2010 from Sears. Told me the washer had a sensor to measure how much water it needs. Was told by service guy that was a blatant misrepresentation by the sales person. It only fills up with 8 of water. When I wash my white towels with normal dirt (dog paws), with HE detergent and bleach on various cycles, my towels come out tie-dyed with dirt. Totally dislike this machine.

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

We bought what was supposed to be the top of the line Maytag dishwasher as part of a kitchen remodel in 2011. Well tonight it has quit working for the 3rd time! I think this is the last straw for us! Tired of spending all this money having it fixed. We also bought a Maytag microwave at the same time that has been nothing but trouble from day 1, but not as bad as the dishwasher. I can promise you we will never buy another Maytag product ever. Heck at this point, I would not accept a free Maytag machine of any kind! Stay away from Maytag!! Just to be more specific, the first time the dishwasher quit it was the board and cost us half as much as the dishwasher. I see lots of mentions of boards going out early.

Our home has seven Maytag appliances: an upstairs kitchen, downstairs suite and laundry room. All were brand new six years ago and what we thought to be good quality by the price we paid for them. We have lived to regret ever dropping a cent into Maytags business account, as we have had nothing but trouble with them. We dont have small kids or teenagers abusing them. Its just us and a very responsible single adult downstairs. And every time we turn around, one of them is costing us nothing but money and grief. Our first problems began with our upstairs fridge when it was only two years old. At that time, it cost us $400 and since then, it just goes on and on. Last week, our downstairs fridge quit, and today, our upstairs one quit. We have had work done on our range, as well as our washing machine and dishwasher. If you are thinking of buying a Maytag appliance, dont, unless you like to throw away your money. I couldnt believe when I looked up Consumer Reviews on Maytag appliances tonight that I would find only 1 out of 5 stars, and read all the terrible reviews written by angry consumers. Well, add me to the list because I will never buy another appliance from Maytag again, and am beginning to think its time to sell this house to get rid of these stupid, useless, pieces of ** Maytag appliances! Sorry, people, but I cant afford to keep replacing them!

We purchased this microwave in Jan. 2012 to accompany a Maytag double oven for our kitchen remodel. Last night while using the microwave, 2 sparks shot up out of the top of the microwave and an electrical surge noise. I quickly un-plugged the appliance. The next day I attempted to use the microwave again and dense electrical smelling smoke poured from the top of the microwave, again un-plugged the machine. I have called an appliance repairman since the 1 year warranty is up. This machine is not even 2 years old and we will never again purchase a Maytag product. PS If the problem is the magnetron (whatever that is) I will contact Maytag for the warranty information.

I have to rewash many load of dark clothing because pale white smears appear on the clothing most times. Ive tried various cleaning methods to try to remove any residue that might be in the walls of the tub. Unfortunately, I cant afford to replace the Maytag white elephant model 500XWZ, serial C31430894. I no longer have the receipt. Buyer, beware. No Maytags in my future.

It sounds like an old threshing machine... I have to close the laundry door it is so loud. People cant believe its a new machine. So saving water is the big deal we hear so much about...but water is the main cleaning agent and it hardly covers the clothes even on a full load coverage. Do not use bleach in the machine unless the load contains ONLY WHITES. It just destroyed a new pink top as it spurts out the bleach without any controls. It does not get whites or clothes clean and just twists the clothes to the point everything you wear has to be ironed. There is not one good thing I can say about this pair of appliances except BUYER BEWARE~ I wish I had read the reviews... Buy the old...tried and true.

Less than four years ago we purchased a new set of Maytag appliances, refrigerator, stove, dishwasher, microwave, and upright freezer. To date, the only appliance we have not had a problem with is the microwave. The bottom element is not working on our stove model # MER8775AS. We will never buy Maytag or Whirlpool products again. Save yourself time and money!

This a 28-month-old bottom freezer fridge purchased from Home Depot. At about 26 months, the freezer started to leak water as ice was completely covering the bottom of the freezer floor and the excess water would then run out once the door was opened. I managed to get the ice out with slim bladed putty knife and did this about every 10 days. Contact with Maytag affirmed that I had no warranty available as it only comes with a 1-year, except for the compressor. Every effort was made to sell me an extended 1-year warranty for $330, and then a technician would be sent to fix the problem. I asked if the compressor had failed, would I be discounted as it is warranted and the answer was no, the fee was still $330. I had great difficulty in explaining why I would purchase a warranty for an item that is already warranted to no avail.I decided to go with their 2nd option of having a local appliance tech to solve the problem at my expense which I did for a final cost of $130. Technician came and immediately knew the problem and removed a little black rubber stopper valve that is supposed to let water pass but gets clogged and the water backs up into the freezer. It took him all of a half hour to fix everything, $85 for the visit and $45 for time in place, $0 for parts. He stated that this is a continuing problem that he has seen many times. Moral: Dont buy any Maytag products as the Maytag repairman who had nothing to do has died.

I bought my Maytag refrigerator Sept. 2013 and now in December, 2014 it is dead. After five visits from Maytag to repair it, they say it will cost $1,200 to repair it. The advice the man gave me was throw it out and buy something different. The refrigerator never worked right from the beginning. Four of the visits were in the warranty period. Compressor and evaporator shot. NEVER AGAIN. Maytag does not stand behind what they sell.

Maytag Bravos XL does not use enough water to wash a load, also does not rinse all the detergent out. I have tried smaller loads, less detergent, nothing helps. The loads have been so small that I have to wait for two or three loads wash before I can dry the clothes. Too small a load in dryer and the sensor will kick off that the load is dry.

I purchased this product at an authorized Maytag dealer sixteen months ago (Maytag front-Loading washer, model MHWE55OWW1) for approximately $1,500. The main bearing and drum are now shot. Maytag has acknowledged that it is likely defective. Notwithstanding their conclusion, Maytag has chosen not to offer a repair or replacement. The conclusion is simply that Maytag does not make a very good product, and any prospective purchasers can expect that they will not get any customer support for their products.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

We purchased a wall oven model MEW7530DE 11/8/2014 which was installed the first part of December 2014. From the beginning the temp was not constant and everything baked was either burned or under baked. The first repairman said the control panel was faulty and was replaced four months after purchase, the problem continued. After three more repairmen all from different companies concluded they could find no problem and thats just how ovens work now. We contacted the owner of Hamiltons Appliance, where the oven was purchased, and requested a replacement oven which was accomplished December 2015.New oven, same problem, very disappointing. My wife has been baking for over 50 years and has never experienced problems and frustration on this level. The condition of the oven is totally unacceptable and with all the effort by us and others we are at a loss. We purchased an extended warranty which has resulted not fixing of the problem. We hired an electrician to inspect the wiring in case that was the problem, costing us $200. The wiring was all good. What do we do next and what are our options short of another new oven. WHAT IS MAYTAGS RESPONSIBILITY? Respectfully, a very unhappy customer.

I purchased Maytag Centennial Commercial washer and dryer eleven years ago. Both are still going strong. It has been a great purchase. Only issue is a couple of stains have appeared on outside of appliances.

I purchased Maytag Bravos MVWX500XWO top loading high efficiency low water washer and it is a piece of junk. All my clothes came out horribly wrinkled and ruined a white jacket when I used the color safe bleach dispenser. I purchased the machine from Sears, where I purchased the extended warranty. I had an A&E technician out and he explained that the new technology of machines are expecting all clothes to be dried in the dryer. Okay, but what do you do with clothes that say hang dry and they come out so wrinkled and twisted that even an iron cant get the wrinkles out? Another suggestion from the technician, put the hang-dry articles in the fluff cycle of the dryer. Well, thats a big nugatory since they are supposed to hang dry them. Supposedly, this machine is all about energy efficiency but isnt it a contradiction when you are using more energy with running a dryer? Someone suggested to me that perhaps there wasnt enough water being dispensed during the spin cycle resulting in horribly wrinkled clothes. Either way, I am on my last nerve with this machine. I always thought that Maytag was an elite company. Well, how wrong I was! Their customer service is pretty much not customer-oriented. Its all about the almighty dollar. After speaking to a supervisor, she explained to me that I should contact Sears with my complaint that Maytag had no recourse. Well honey, Sears did not make the atrocious machine. They are just the so-called messengers. I have unfortunately found that once Maytag sells their horrendous product, they dont even stand by it. Now isnt that typical of companies nowadays and sadly, lacking with this company? Pride in their workmanship! And again, its all about the almighty dollar and who gives a ** about customer satisfaction? Maybe thats why they dont have the Maytag repairman. He was ashamed to be associated with this irreverent company.

I live in Southern Indiana and bought my appliance from Charlie Wilsons for 25 years. 3 years ago my Whirlpool washer quit filling up to full level. I decided to move it over and use for my car and pet towels. When I bought my hose in March 1999 every appliance was Whirlpool washer, dryer, refrigerator, stove, dishwasher. GE is made in Louisville, KY but I dislike the union.Anyway I bought a Maytag model MVWC415EW1 June 2017. Recently it started making a grinding noise when going in spin cycle, wadding cloths up and leaking black water on basement floor. Called repair shop out. I just do not have the time to repair stuff anymore. They came out $80.00 service call and tell me at least $300.00 to repair. Wait a minute. $500.00 to buy a new one over $300.00 to repair. Guess what I did? I called Maytag and complained. CASE NUMBER **. They reviewed and denied. Not a problem. I said, I guess you do not need me as a customer anymore.I have twenty year old Whirlpool washer and dryer still running, I have replaced my refrigerator (Old one in garage still running a colder than new fridge and day of the week). Bought Amana=Whirlpool and it has quit and replaced with a Whirlpool July 2019. Nothing is built like it used to be BUT we still pay as much if not more. Off I go to Charlie Wilsons to buy a $1000.00 Speed Queen washer with 7 years parts and labor warranty. Had to order it but old washer still running just not going to full mark.

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

My Maytag washer (model number MVWC400XW3) worked well for 6 months. Suddenly, it started making terrible loud noises when spinning. Repairmen have come out 6 times, and I got second opinions. It was turned over to another repair company. Transmission has been replaced as well as the motor. I have been without a washer for 3 months. Repairmen would come out, replace a part, and leave; and the washer is never fixed. I asked the repairmen to stay for an entire cycle, but they act insulted and left, saying its fixed. When I tried to wash, everything went crazy. I unplugged the washer and plugged it back in to reset it. I turned the dial to spin, and the lights said the washer was sensing. The lights never moved off that. The washer sounded like its trying to wash, but theres a strong grinding noise. When does the repairman decide he cant fix it? My husband is insisting we go buy another washer. The washer was bought in September 2011, so its still in warranty. In addition, we bought a five-year warranty. The repairmen stay 15 minutes, plug in a new part, and leave. They dont come back for two weeks. Will we ever get this washer fixed or get a new one. How do we put pressure on Maytag to fix it or give us a new one?

About 9 yrs ago, we remodeled our house. And when it came to appliances, I was vehement we were going to go with Maytag because of their great name and reliability (We have 7 sons and needed reliable appliances). Boy, was I ever wrong?! We have gone through 2 Maytag dishwashers and countless repairs to the Maytag dryer. And our top of the line refrigerator has been a piece of junk!Of course, shortly after the year warranty was up, the flimsy pieces of plastic holding up the shelves started breaking off. The repairman, who came to replace the cooling coil on the refrigerator, said those shelf plugs couldnt be fixed. The whole front of all drawers have come off as well. He mentioned that Maytag was going bankrupt and started compromising on fit and finish. And he said that we just happened to purchase in that time frame. Now, we have a compressor that needs to be replaced for over $500! I have, in my garage, a Gibson freezer from my grandma that is 40 yrs old, and literally the most reliable appliance we have. Never have we made any repairs to it!I called Whirlpool (since they bought Maytag) to tell about my horrible experience with Maytag, and let them know we have to replace these appliances. I asked if there was anything they could/would do (discounts whatever) to redeem their name. I was told that they would not be able to help at all. So, I told them that I would not give Whirlpool anymore of my business and warn anyone I could, not to buy Maytag, Whirlpool or Amana. Isnt there any appliance company out there who cares about customer service, a good name and a reliable product?!

I will never buy another Maytag appliance. We built our home in 2005 and bought brand new Maytag kitchen appliances (refrigerator, gas oven/stovetop, dishwasher, and hood microwave). In seven years, we have had problem after problem with all four appliances. We had to replace the compressor in the refrigerator in the first 18 months and then the fan in the refrigerator about a year ago. We have had to replace the heating unit in the oven twice and the handle has broken off of the oven door twice. We have had to replace the handle latch on the dishwasher once and today, the microwave stopped working. We are not rough on our appliances (especially the microwave as we rarely use it), so I think the fact that every single Maytag appliance has broken down one to three times in different capacities in the last seven years says it all. We have had a very poor experience with this brand and will definitely never buy another Maytag appliance.

Low water level resulting in poor cleaning. Very poor design. Requires 2 rinses so the water savings of the wash cycle is a joke! Im very disappointed with the so-called Maytag quality. If doing very very small or handwash loads it work somewhat ok! Would never buy Maytag again!!

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.

I bought the washer dryer combo. Dryer already broken. Washer is very loud when it changes gears. Would not recommend the washer or dryer.

My washer is less than 3 years old when I noticed the bleach dispenser has filled with water. I soaked the water out with a towel only to have it fill again the next time I washed. This in addition to the feeling I have that too much soap is left in clothes and spot removal is pretty consistently negligible.

Maytag Bravos XL - I am having the same problem as everyone else with this washer. My clothes do not get clean and they smell. Maytag advertises tumbling, rubbing action to get clothes clean but my washer does neither. The clothes lay in the bottom of the tub and never move except when in the spin cycle. I am going to file a complaint with Maytag and if they do not refund my money am going to file a DTPA claim against them for false, misleading and deceptive advertisement. They will have to pay up to three (3) times the purchase price of the washer. Maybe everyone else should consider the same.

My dishes come out super clean and I love it, even when there is calcium build-up around the filter. Thanks to Maytag and their great technology. You cant beat Maytag.

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

The washer does not wash the clothes, period. It leaves dirt and soap in the machine along with the unwashed clothes.