I purchased a Maytag 4-door model, a little over three years ago. A little over a year ago, I noticed small puddles of water around the bottom of my refrigerator on the floor. I blamed the dog for having accidents and shrugged it off. Well, after months of putting up with this I came to the realization that it wasnt my dog, so I started looking for leaks on the seal, etc. Thats when I realized that the entire floor of the freezer was one solid block of ice! So, I looked online for people that might be having the same problem. Sure enough, there are A LOT of us!!! Now to add insult to injury, I have to have a MAYTAG certified repairman come and look at what needs to be done! He only charges $85.00 just to come to my house!!!! Thanks MAYTAG, I spend $2500.00 for a refrigerator thats obviously defective, and still have to pay more to have it repaired!!!

The machine does not rinse soap off clothes even after using 2nd rinse cycle. You have to wash clothes again using no soap at all. Defective machine maytag does not help or Clare wanted to charge service fee for tech even though machine is under warranty. This washer should be recalled. Very bad product. Lots of complaints.

My 20 yr old Kenmore washer broke last month so I replaced it with a Maytag I bought from Lowes. I wanted a simple washer that would maybe last 10 years. The Maytag has a sensor for everything. So you can’t fill the washer, it determines how much water to use and it never fills enough to cover the clothes. It doesn’t agitate really. It’s more like a slow on & off movement. It does everything in an on & off way. The water fill goes on & off, it “washes” on & off. Even the spin is a spin, slow to almost stop - spin again - almost stop - spin again. It also stops filling if you open the lid, I tried to let some water fill before adding clothes (so the liquid detergent could dilute a bit) but every time I opened the top there was no water in the drum, I heated the water running and the drum was wet but it wouldn’t gill at all. I think it only puts water enough to “sense” the clothes have been soaked. I will call Lowes and try to return it.

My oven looks like it has never been cleaned. The self clean Aqualift does not work to clean your oven. If I would have known that this feature did not work for self cleaning I would never have purchased this oven. My old cheaper oven at least came clean on the self clean cycle. Now it seems I am going to have to scrub my self cleaning oven. What a waste of money. Will never purchase another Maytag appliance.

I have always bought Maytag and never had a problem except with this new washer. Our clothes smell like dirty laundry and when done washing there is lint in the creases or folds of the clothes. I am using a product for cleaning the washer each month, but our clothes still have an odor. I do not like the way the washer works, it just moves back and forth slowly, but the clothes dont circulate enough.

This washer has been the biggest disappointment of any appliance I have ever bought. Purchased 12/2012 and immediately disliked it but thought I needed to get used to the new style since my previous machine operated for 23 yrs! It is loud and does not clean as effectively as my last machine. It stays in the Sensing mode for 15 mins or longer. Rarely will it spin as it should. Most loads, after the sensing stops and the lights go out, I have to move the dial to Drain/Spin, wait for it to sense again and then maybe it will spin. If this doesnt work I have to unplug the machine to allow it to reset. I called Maytag and was told there are no known issues with the machine. I google this model and find many customers have had a similar problem.

Washer leaves spots on clothes and massive knots in clothes. The serviceman has been here twice since we bought it and was told to use extra wash option and heavy load wash with fabric softener option as well, and to only use about one tablespoon of detergent. So much for the green option! Results, still washing clothes 2 or 3 times per load then into the dryer. Tried an experiment - washed a pair of my daughters white capris and then washed them at a friends house while water was saved in a separate tub. Holy crap, the dirt in the water. Do not buy this machine. Not even if it is offered to you for free.

We bought our front load washer and dryer about 5 years ago and have had no problems with either. We also purchased a Maytag French door refrigerator 2 months ago to replace our Sears Elite brand when its compressor went out after 27 months (Ill never buy another Sears appliance).

We purchased a Maytag Bravos Automatic Washer 6/28/09. The interior enamel around the bleach dispenser started rusting about six months ago and it’s getting worse. Our white clothes are getting rust stains on them. Otherwise the machine works well, but what a huge flaw. We will buy a new machine, but not a Maytag.

My wife and I bought the Maytag commercial Bravo set about 5 years ago and both the clothes washing and dryer machines are still working as great as the day we bought them. Im a bit biased though as I bought Maytag commercial products in the past and will continue to do so because its they are a dependable company made a reliable machines.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

I am 65 years old and for all of my life there has always been a Maytag washer and Dryer in our home. My great grandmother and great grandfather had a gasoline powered Maytag. My maternal grandmother had wringer-Maytag and my parents have always purchased Maytags. When I was on my own I purchased Maytags. In November of 2012 I purchased a Maytag Bravos XL washer and dryer. I had no reservations because it was Maytag. In October of this year (2017), the washer starting roaring and I had purchased an extended warranty. I called a reported this. A local appliance repair provider was sent out after I called the 800 number on the warranty agreement. I waited several days and finally called the repair provider and was told the parts needed were backordered. Time rocked on several weeks with no communication until I began calling both repair provider and warranty company. Still no washer repair. Ultimately, the resolution was not to repair or replace the washer, but to refund the purchase price and sales tax. The Home Depot salesman that sold us the washer and dryer, as well as the extended warranty coverage assured us that should either the washer or dryer fail it would be repaired or replaced, neither occurred. This left me without a washer for more than a month. Then finally I called the warranty company used by Home Depot and I was told a refund check would be sent for the washer, along with laundry reimbursement check. My difficulty with this is even though I got my money back on the washer and some of my expense on having the laundry and dry cleaning done elsewhere, it does address the issue. Simply, I see the Maytag commercials all the time and they are simply noise on TV now. I am still wondering how this could happen to a washing machine that had less than two and half years of use, never abused, cared for could fail in five years. I was used to having Maytags last decades with little or no repairs. Given the fact this machine was top of the line and well taken care of, I so very disappointed and not buy another Maytag of any kind again. By the way, I have a home in the country with a 27 year Maytag washer and 20 year old Maytag dryer that come from my home in town that Bravos XL dryer replaced. My research during all of this has led me to conclude this is not an isolated incident, but far larger problem with these washing machines. Why has there not been a recall on these inherently defective washers been issued. Where is the justice in this, even though the refund and small laundry reimbursement has been received it does not make any happier. I have lost my confidence in Maytag and I thought that could not happen with Maytag.

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

Maytag Maxima 9000 washer not working since day 1: I have placed a call on Friday, June 14, about my Maytag washer not working. The service man came in on Friday, June 15, 2012, and stated that a UI board needs to be replaced. I have called Whirlpool to ask for the part to be ordered so it is faster, could not do anything. Then, I have not heard from Whirlpool since. I called them again on Wednesday, June 20th, and I was told that the part was ordered and it will take up to 10 days for it to arrive. Once it arrives, the technician will call to set up an appointment. So, according to Maytag (Whirlpool), I can be without a washer for at least 2 weeks (as 10 days are 10 business days) and it is all good.

The AquaLift Self-Cleaning is a very poor substitute for a normal high temperature Oven-Range. It gives as much work as an oven without any self-cleaning, as it does nothing to the sidewalls or the door. The minimum temperature is 170 Fahrenheit, too high to rise a dough.

Bought the set at Home Depot. The gear box went out after 2 1/2 months of use. I called the manufacturer warranty site and spent close to an hour on the phone then was given an appointment to have a service repair person look at it. Two days before the scheduled service call they called and said they would have to move the appointment out by a week. After diagnosing the problem, oil all over the floor and stained clothes from the oil, was told it could be up to 2 weeks until the part arrived and installed. So my warranty is being used up while the machine is out of service for a month. Beware of buying a Maytag!!!

I purchase my Maytag electric glass top stove 9 years ago. 2 years ago, one of the burners went out and had to be replaced. Now, in the past 2 days, my oven is taking FOREVER to preheat from 0 to 455 degrees. So far, its been 78 minutes waiting for it to go from 0 degrees to 425! Apparently the heating element is defective. As far as the self cleaning oven, it is absolutely worthless, and does NOT work! Needless to say that Im very disappointed, and looking at another repair expense!

We purchased our Maytag 4000 series washer and dryer (Model: MHWE450) in December 2010 from Best Buy. For the first six months or so, we were very happy. We started to notice that the washer was getting a little louder by the month. I checked the level multiple times to be sure that wasnt the issue. Assuming it was just part of how the washer broke in, I just let it go - a bad move! Fourteen months after I purchased the set, the washer flooded all over the floor. I opened the washer and pieces of plastic were all over our clothes. After further inspection, the drain was completely full of the same plastic. I cleaned it all up only to find that the washer tub was so loose that it was banging side to side.I called Maytag to ask for help or suggestions. They basically told me that I was out of warranty and kind of out of luck. I responded that we do a total of four to five loads of clothes per week and that there was no reason that this commercial series washer should have failed after 14 months. They offered a one-time service plus extended service contract. Feeling that I had no choice, I spent almost $400 assuming that I had a fixed washer and a year extra warranty. I was told that someone would be out to look at the washer in three days. Finally, after me pressing and pressing, someone showed up a week later. He put a list together of all of the items that were needed to repair the washer.Two days later, Maytag service calls and says that the washer will be too expensive to repair and they would be giving me a reimbursement for buying a new one. They didnt have an exact amount yet. Two more days later, they finally called me with an offer of around $550 ($250 less than what I paid) based on their research of what I should be able to find one for and directed me to the website. One big catch though - it didnt include the $125 shipping charge. When I called to request for it to be paid as well, they declined with basically a “take it or leave” type of attitude. Not knowing what to do, I called every local appliance store until I found someone that had two in stock. When I went to look at them, I was told that both of the ones that they had were rebuilt because that model Maytag washer had a major issue with the bearing and basically needed to be replaced on all of them.Luckily, I was able to buy the washer and a five-year extended service contract for around $690. So in the end, I paid $799 for the new washer, $400 for a warranty, another $100 to replace the washer, and close to $100 in laundry mat costs for three weeks. I promised everyone that I spoke to with Maytag that I would write a review to share my story and thats why I wrote this. The repair plus warranty is a joke. I like this washer/dryer but will never buy another Maytag appliance again. Next time, I will buy extended service contract from the start.

I bought a Maytag Top Loader. I soon discovered that it is not possible to do a cold water wash. After much communication with Maytag Customer Service it was determined that there is no way to bypass it. And it uses a lot of hot water, even on a cold wash. Their explanation was that the water needed to be a certain temperature to make the detergent work effectively. The same detergent that I’ve been using for 40 years with cold water in my Speed Queen. When I need to do a cold water wash, I go to my parents home and use their washer. Disappointing purchase, my last Maytag, for sure.

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

I bought the Maytag MVWX700XL1 (Bravos X) model in 2012 from Home Depot. I paid over $800 for this washer. I knew I was in trouble when I found dry spots on clothes after the washing completed. I started using the Bulky cycle. So much for saving water. It has not been overused, its only two of us. Today the spin cycle sounds like a train. The washing cycle has stopped working completely. Im very dissatisfied with this washer.

I purchased Maytag Bravos XL Steam Washer brand new from Lowe’s in January 2018. HORRIBLE washer! Does not get clothes clean and leaves soap and scum all over clothes. I have to wash everything on power wash with an additional rinse cycle (takes about 2 hours per load) and clothes still don’t come out clean. I often have to wash a load 2 or 3 times to get it clean. Will NEVER PURCHASE another Maytag product! What is even worse is that I also bought the Maytag “commercial technology” washer at the same time. It’s an even more TERRIBLE washer. Cannot get through one cycle without getting an LF (low flow) error & the cycle shuts off and machine drains & quits. Absolutely the two WORST washers I’ve ever owned in the past 40 years!!!

Dont buy this machine. Although it is an HE machine and supposed to save on water, it does not give enough water to at least cover the clothes. I had repair come in and they changed the computer but no improvement. The cycles determine the water amounts not the type of clothes you are washing. So if I only a few things I use cold water wash, if I have a half load I use deep water wash and have to add water to it. Its ridiculous. Do yourself a favor and get an LG. I wish I had.

I have had my washer and my dryer (model no. MGDB850WQ - serial no. MJ3311087), for 1 and 1/2 years. I have given both plenty of time and since the beginning, I have literally hated these products. This was a large purchase, so I feel locked into a terrible choice. I wish I had never bought these two items and will never use Maytag again. I will also never recommend these products to anyone. I do not like the new technology.

One month after warranty we had our first issue which cost us $380. Kinda my fault I was told by repair guy... My bra underwire came out during wash and destroyed the part we had to replace. Then a year later during spin cycle it sounds like an airplane taking off for about 10 minutes. Its so loud we cant even hear our TV! So guessing its bearings gone bad now? Which is a very difficult part to replace. And pricey. So guessing a new washer is in our future. We previously owned a Maytag washer and had it for 15 years and it still worked fine, we just wanted to upgrade. Big mistake! I wouldnt wish this washer on my enemies. I think the repair guys sets it to mess up when they do this reset thingy. Lol. Cause within a month of the renewed warranty we purchased was expired is when the 2nd issue began. I think the older washer are better because all this newer technology stuff is crap!! My advice do not buy Maytag Bravos series washer unless youve got lots of cash for repairs!!

So I read the reviews when I bought this Maytag Bravo Washer and figured stuff happens. We bought the top load Maytag Brava in 2013. We bought the Home Depot warranty, 2 years later the washer was leaking water. 5 repair visits and 3 attempts to fix the leak before it was repaired. As of 4-25-17 the wash machine displayed un-level errors and started vibrating with a thundering noise. Called out warranty repair and they stated we need new bearings. Repair is scheduled in 2 days and now the wash machine is thundering and spewing oil so it is shut off. 4 years old, and like the other complaints clothes come out with dry patches and not clean. This is a bad machine, we are saving for our next washer. It will have an old style spindle/agitator, no California efficiency and probably not Maytag.

My 1 year old Maytag Bravos 300 dryer caught fire on Nov. 21, 2011 after the first one was replaced. Firemen came. Luckily, it didnt spread to the house. The first one wouldnt dry my clothes.

Failure to drain after 3 years. Was disappointing so repairman fixed problem, a fuse, in 3 minutes but charged $300! Since then I make my own repairs and have had no problems that I can complain about. Both Maytag Neptune drier and washer have worked well. Buzzer just failed.

WOW! I cant believe I bought a Maytag MDB7749AWM1 Dishwasher without reading any reviews. Paid $650 for it a couple of years ago and the control panel is bad. $390 to repair it, unbelievable! Sounds like Maytag has a major customer service problem because I will NEVER BUY A MAYTAG DISHWASHER again! Spent $5000 grand on new Maytag appliances thinking they were the best to replace the outdated ones. Not the same, not sure what youre doing Maytag but youre losing a lot of loyal customers. What a shame! My old dishwasher lasted over 18 years and I didnt have any problems. 2 years? Come on!!! Same problem as the other 5000 people, someone needs a career change!

Worst experience of my life!!!! Don’t buy a Maytag washer!!! It’s agitating our clothes dry. Putting holes in clothes. We bought a warranty that’s pretty much useless. They will not replace. Only fix parts.

We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

This is a dishwasher purchased at Home Depot on March 25, 2012 for a rental unit... call from tenant said the dishwasher did not work. Repair person from Appliance Hospital went out today and said the control panel is out and the touch pad. Cost is over $500 to replace. I will have to replace this dishwasher BUT NOT WITH ANOTHER MAYTAG.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

I love my washer. I have had it for 13 yrs and has only needed repair once. My complaint is the gasket on the tub has black mold that grows on it. I have cleaned it with bleach, bathroom cleaner, alcohol, but it always comes back. What can I do to prevent illness from mold?

Model #MFI2670XEM0, Maytag fridge top French doors, bottom freezer. Purchased fridge in May 2011 from Lowes, with a matching microwave. A couple months ago, I noticed puddle of water on wood floor in front of fridge, so I opened freezer to find ice on bottom with a sheet of fresh water on top. Call to Maytag was useless, also tried to sell us warranty. Guess that $300+ warranty would cover one year, so after the warranty runs out, would we have to buy another when it plugs again. Our kitchen floor is ruined, and the warping is coming close to our dining room. Googled problem online to see if there was an easy fix since it was out of warranty. I tried to defrost as described online, only to have it leaking again a couple weeks later. Will never buy a Maytag again. Guess that repairman in commercial is never busy because Maytag wont stand behind their products.

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

I love the front loading machines. Fabrics dont get beat up like they do with a top loading machine with an agitator. My Maytag front loader doesnt have as many bells and whistles as others, but I love it nonetheless. Reliability was very important to me when I bought it, so I talked to a couple repair men to see if this was one they worked on a lot. When I found out they didnt, I bought it.

We have to rinse off any food particles before we wash or it may not wash off. So I use plastic wiper before we load. Only 2 of us so items may sit 3-4 days before we run our Maytag dishwasher.

I have owned my Maytag washer for approximately five years. Ive always used the recommended detergent and religiously used the tabs to clean the machine when it was required. I have never abused the machine by overloading it, using too much detergent, etc. It is now coming up with an LF code. There is no one in this area who does repairs and if I do find someone Im sure theyll want some exorbitant amount to come all the way out to the boonies to give an estimate and the repairs Im sure will be hefty. I take very good care of all my appliances and expected this machine to last much longer.

Bravos XL washer - I agree with others, if I won the lottery, this would be on the street in two minutes. It is a complete waste of money. Nothing comes clean. Supposed to be water efficient, well not when you have to wash everything multiple times and I have to do them in such small loads to have any hope of anything getting clean. Some clothes just never look clean. I have the same issue with all my dark things coming out with white residue and yet I use liquid detergent. I follow all the instructions and do the monthly Affresh tablet (cash grab) and still nothing is ever clean. I am SO disappointed in this machine. I thought Maytag and Whirlpool were good brands but not anymore. I also get a constant HC error and there is nothing wrong with my water lines. Just so disappointing, save your money and frustration and buy something else!!

This dishwasher is extremely quiet and very attractive in the kitchen. Easy to use and does a great cleaning job. The price was also right. Would definitely buy again.

Not yet two years old, my Maytag Bravos dryer stopped working. When I called a technician to see what the problem was, he told me that the circuit board was burned out and it would be $500.00 to replace. I then called Maytag to find out if there was a problem with this machine and was told no. This apparently is a lie as there were numerous complaints when I checked the internet. I have five Maytag appliances and at this point, only one has not caused a problem. Maytag is not the company of the past when if you had a Maytag, you had the best. The repairman no longer sits around with nothing to do.

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

It’s a front loader, very quiet, and uses less water. The clothes come out clean and less wrinkled if you take advantage of the settings. l like the extra rinse and the drawer underneath. The capacity is able to accommodate enough clothes so I only need to do a load of darks and a load of whites each week.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

I like most others have experienced the same issues with the new Maytag top load WM. In addition my new machine dances across the floor like a drunk leprechaun. After Lowes told me that with my extended warranty Id have to miss work and pay 100 bucks for a service call I emailed Maytag. Needless to say they didnt even respond. Ive have learned a few valuable lessons. Dont assume that more money means better merchandise. Made in America doesnt say much. And please dont buy Maytag.

Purchased this Whirlpool made Maytag Stainless Steel dishwasher Feb 2013. By Jan 2017 the washer was no longer operational. Due to poor factory design the touch pad wiring harness was crushed during the initial assembly. The harness is routed behind the touch pad/pull handle faceplate in the door. The factory design provided no clearance for the harness. Obviously after little use (opening and closing of the door) the pinched portion of the harness behind the pull handle becomes compromised causing the ELECTRICAL SHORT.I phoned Whirlpool the maker of the Maytag Stainless Steel Dishwasher for assistance, all they offered was a repair plan in excess of $300.00. I purchased this supposedly quality American Made Whirlpool product as well as a range, microwave, washer and dryer in the spirit of supporting US labor. Now Im stuck with a dishwasher that has an ELECTRICAL SHORT, possibly a FIRE HAZARD and Whirlpool trying to milk me for more money. Please think twice before purchasing anything from this Michigan based company.

We bought a Maytag refrigerator less than two years ago because... its Maytag. Less than a year later we had five service calls. The refrigerator wasnt cold, the freezer was the temperature of the refrigerator and it took two months and two different repair companies to fix it. And now... yes, the same problem seems to be occurring. It was a leak that was supposed fix. Cant bear the idea of going through this all over again. NEVER again Maytag!!!

These machines have lots of service problems, although Im not familiar with the newer models. The function and the features are adequate, and typical. And overall, again, I have no complaints other than shortly after purchasing, there was a circuit board recall for these machines, and fortunately, I had a repairman who knew of the issue, and guided me to a cost free fix. Overall, it has served the purpose well of cleaning my clothes in a decent fashion.

We bought a Maytag dishwasher in August, 2014, and already the touchpad is malfunctioning and we cant start the dishwasher! I am very disgruntled and frustrated by this! I should have kept the old Kitchen Aid dishwasher that we bought in 1995! At least it never malfunctioned!

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

The way the side by side fridge/freezer is built contributed to several injuries. I am 60 tall and of normal size, and accessing anything in the side doors lower down always results in smashed head, near bleeding injuries. I am so sick and tired of it. No other fridge has done this to me. Add that to the shelves being near razor sharp. One of these days this fridge is going to land me in the hospital with a lawsuit. Most people are not 3 feet tall or 8 feet tall, thats the only way to use this fridge safely!

Horrible machine. Purchased on 02/28/2014. I am 63 y/o retired housewife now. Machine used only for light washing, occasional king size sheets and weekly towels. I bought into the Maytag name, am so very angry that I did. Started a load at 1215 pm today... it is still sensing, washing, rinsing, spinning and then it starts all over again. Just unplugged from the power source, hopefully I can get the clothes spun out enough to dry!! Call and live chats to Maytag were frustrating to say the least. $400 plus Maytag service call to check out the machine not fix check out repairing would be extra. (I do not live in rural area, live 5 minutes from downtown Jacksonville FL!!!) Independent Repairmen will not touch this Maytag Model (cannot say I blame them!!). DO NOT PURCHASE A MAYTAG PRODUCT. This is a horrible company lacking in integrity, honesty and fairness. They sell shoddy, inferior products based upon past history.

We purchased the Maytag Neptune washer and dryer on May 2005. We purchased it for $2,000. We have had so many problems as we have replaced the drain pump 2 times because of objects getting stuck in it. We have also replaced the door switch, as well as flooding my laundry room floor several times.In 2006, we received a notice of recall. We responded to the recall and were supplied with a GFCI plug for our washer, as this was to prevent the control board from catching on fire. In September 2011, the control panel on the Neptune washer failed. I now have to purchase a new washer, as this is an expensive fix. With this poor workmanship and problems that we have encountered, I am very disappointed. This was a lot of money to spend on a washer, only to last 6 years.

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

Two years ago I purchased a Maytag commercial technology top-load washer. It only two options for water level, either deep water or Auto sensor. Because I live alone I have very small amounts of clothing to wash at a time. Therefore I was excited about the auto sense to save water. However when using the auto sensor theres such a small amount of water in the drum it does not cover the clothes being washed and often I have items of clothing come out of the wash cycle and rinse cycle with dry spots on them yet. The clothes dont get clean and begin to smell stale shortly after theyve been washed. I contacted the business from which I purchased the machine and they were not able nor willing to do anything about my dissatisfaction. This is the worst Appliance I have ever purchased in my 64 years hows life. I hate this washer. It is totally ineffective. And now Im stuck with it and dirty clothes.

Our front load washer is two weeks past the one year warranty and need $650 in repairs! I will never purchase a Maytag product again. My last Maytag was 19 years old when we got this new front loader for energy efficiency. You dont save money when you have to replace it after one year.

If I could give this a 0-Star rating, I would! I cant believe Maytag would make such an awful washing machine! Within the first 2 weeks I called their service department because (in my opinion) the washer wasnt washing properly. It took over a month and several calls to get someone out to look at the washer & dryer. According to the technician, both machines were operating properly. Apparently the washer is designed to destroy clothing and bedding! The gentle cycle set on deep fill will add just enough water to get the clothing wet, then agitates for about 10 minutes, then it fills up, agitates for 3 more minutes and drains. During the 10 minute dry-run, I watch my clothes get destroyed! I have never seen anything like this! My sweaters are shredded, my tops are pilled up & in a garment bag this thing managed to destroy a sports bra! This machine has ripped my mattress cover in several places and pulled my sheets from excessive rubbing due to not enough water. And what is up with the slow fill? The technician informed me that the trickling water is also normal. If I could return this washer, I would! I will never buy another Maytag because my Bravos washer died after only 4 years, and this one is brutal!

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

Not only did I buy a Maytag washer for the brand name and trusted longevity, but because they were always a good product in the past. When my Maytag EZ-Epic washer drum failed after only owning it for two years, there was no effort made by any associate to cover this under any sort of warranty at all. To replace this part, I was quoted so much money that I could go out and buy a brand new one for the cost of the repair for this faulty part. I am extremely dissatisfied with the way I was treated because the so called product was out of warranty and I will never buy a Maytag product again. Shame on Maytag for ever selling off to such a fraudster of a company.

Bought a Maytag Dishwasher (Model No. MDB7749SBM2) in Sept. 2013 and I am in need of repair for the control panel. The dishwasher is in a vacation house and isnt used on a daily basis. I always thought Maytag was a reliable product but Ive been reading the reviews and the control panel is a problem on relatively new units. How do they get away with this. The unit was around $600 and now Im stuck with a big repair bill... and it appears, from what Ive read on this site that it is a common problem. Maytag has replaced the control panel part and, as far as I am concerned, they should have provided them to all the consumers who were stuck with the defective ones they sold us in the last few years. Now we all know why we dont see the Maytag repairman sitting around with nothing to do on TV. Hes working his ass off trying to fix the dishwashers.

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

I cannot even begin to describe my disappointment in these overpriced machines! Bought a 4-year extended warranty when I purchased and two weeks after warranty expired, my heating element went out on the dryer. This repair cost over 300 bucks. Six months later the washer was making some crazy noise and service guy could not find the cause...another $120 bucks. A few months later the same noise...this time a coin had slid under the bottom plate and caused damage to the machine...another service charge of over $200 bucks plus I purchased an extended one year warranty at $189 bucks. Thank goodness, because now it is throwing an LD code and will not drain. Oh and I forgot about the service call for the latch breaking on the dryer door...another $119 bucks. The repair guy felt sorry for me and didnt charge me for the part. Tangled clothes when washed and forever to dry. Next time I will buy an inexpensive set like I had before that lasted 16 years with no problems! This stuff is junk!

Purchased a stackable washer and dryer (Maytag) for our new condo in Feb 2015. After it was installed a few months later the problems began. The washer wasnt removing the water from the clothes. We contacted Maytag and they informed us that they subcontract out to a company called Appliance Service of Central Florida (727-462-0394). Contacted Appliance Service and set up a date to be serviced. Since then, we have had Appliance Service out to our place over 8 times. They found fault in our control panel, our door lock, replaced our motor and have replace several other parts. It has been over 4 months since they started repairs on our machine and have informed me that they have a right to try and fix the problem. I have no problem with this but when and how long do I have to put up with this? They dont seem to care that my wife and I havent had a working washer in over 4 months.The people doing the repairs stated that this machine should have been replaced because it had or has several problems with it and after replacing the motor, electric panel etc it still isnt working. When I contacted Maytag they stated that as long as Appliance Service is working on the problem, it out of their hands. Is there anything I can do besides contacting a lawyer and spending more money?

Bravos washer purchased Sept. 2016. I purchased the Maytag washer based on experience and reputation. I am so disappointed in this washer. I have had the control board replaced after only 3 months and it vibrates, shakes and is very noisy. It does not fill with enough water and the clothes are tangled at the end of the wash. I will never buy another Maytag.

I purchased Maytag dishwasher (model # MDBH979AWW3) in June of 2010. Trouble started on washer after 18 months. Touch pad buttons dont all seem to be working. Occasionally gets to run after slamming door multiple times, but dispenser doesnt function properly. After trying to diagnose myself with door switches, connectors, etc., I caved in and called service. Service quoted $470 parts and labor to fix the problems, including control touch panel, dispenser, and control board (seems common from what I read here). Wish I had seen this string of posts before I called Maytag/Whirlpool customer service to see if they would help before I did any repairs. The responses I got from the service rep were rigid and scripted. Only time she varied from the script was to explain that modern high-efficiency appliances dont tend to last as long as ones 20 years ago. 18 months? Really? I might buy that if it was a mechanical durability design issue. Supervisors responses were also scripted, pointing back to the 12-month warranty. She said she did a warranty search on my model and that there was no warranty concern for this problem (really?). If there was, she might be able to help me. I guess there is no warranty history because most failures are between 12-24 months and the consumer has to pay for replacement outside of warranty. No semblance of customer service or customer care, just repeating what is on their website. Response was: I am sorry you are dissatisfied with the product and my response, but there is nothing I am authorized do. Sent an email to Maytag customer service regarding the problem and customer service interaction. They called back saying they stand by the original customer reps response, but offered to have someone else come out to give a second opinion on the problem. From what I read here, that doesnt seem necessary. Wish Maytag/Whirlpool would at least acknowledge that there is a problem, even the auto industry seems to have figured out a way to equip the service industry with known recurring problem history (TSB) and offer token help to keep customer loyalty. Apparently another quality organization fallen victim to short-sighted methods of maintaining shareholder value.

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

Purchased a Maytag range with Aqualift technology in 2013 thinking it was a good brand and *happy* to find a new way to self-clean my oven. This turns out to be nothing but a joke and I am not *happy* with it. After following directions to the letter, there is some loosening of anything on the floor of the oven, but the sides and top are slowly being coated with more and more grease. Ive spent way too much time with my head in the oven trying to scrub stuff without using a heavy duty cleaner but feel I now need to resort to Easy Off as there is no other way to get it clean. I also dont understand why they tell you to remove the racks since there obviously isnt enough going on to even clean the oven... How would the racks be damaged? And now I believe there is a problem with the Dual Choice element where Im not able to turn the temperature down. Even turned back to the low setting, the pan cooks away like its on high. I have to keep turning it off and then back on in an attempt to find something similar to medium or low heat. Im so very disappointed in Maytag and feel this method of oven cleaning should never have been put on the market. Its a scam!

The Deli drawer randomly falls, shelves in general do not fit well. Rough edges on door corners are a hazard especially for children. Service call line was extremely poor with a total disregard to customer concerns. It has been a very bad decision!

Fifteen months after purchase of the top load washer, we have had to call in repair. The lid lock and sensor have went out on the machine and the repair costs are equal to the purchase of the machine. Whether the consumer has an extended warranty or not, this is unreasonable. So hear this Maytag, the CONSUMERS will invest elsewhere when delivered cheap merchandise like this even if it is Made in the USA as you wish to tout in order to bait the consumer for their money instead of providing superior quality American products. This consumer is sending this machine out the door.

Purchased Maytag Jetclean Dishwasher Model # MDB7749SBM3 on March 19, 2014 and on June 10, 2017 the washer would not go through the cycles properly. So I got on the internet to check out the problem. Maytag has very flimsy wiring circuit on the back of the control panel that rusts out due to being close to high-temperature water. Obviously a design flaw. The only way to fix it is to replace the control panel for $150 dollars with another flawed part. Do not buy Maytag dishwasher.

Within a year of purchasing this washing machine, I needed to schedule a repair service because the washer started making an unfamiliar noise. Repair Service shows up and refuses to touch my washer. The ink on the Serial and Model number (stick on label) inside the washing machine door has washed off. Sticker label in excellent shape, except all the ink has come off. If the Repair Serviceman cannot read the label, NO SERVICE FOR YOU. MY SAGA... Did you know that if your washer or dryer does not have a readable serial number on the machine, NO repair service will work on it. It does not matter if you have all the paperwork showing this information. If the original label is unreadable, no repair service will touch it because they will be fired. Maytag changes parts on a model all the time. The serial number is the ONLY way a serviceman can tell exactly what parts your washer was made with. Apparently the serial and model number label sticker was not printed with permanent ink. The Repair Service said the Serial and Model number ink washed off the label because the sticker was incorrectly put on the inside of the washer door at the bottom. But they were WRONG! Maytag shows online that is exactly where the serial and model number sticker is supposed to be located. So, I called Maytag to order a new serial number (stick on) label for our washer. I gave Maytag the information and I was told I would have the label in two weeks. Then I called back a week or so later to make sure the serial number was ordered and on the way. Maytag said there was a misunderstanding, and that they received my request on 6/17/15 and it was sent to the ONE AND ONLY GUY that makes replacement serial number tags and he was sent my request on 6/22/15. Maytag said it would take the one and only man quite some time to make the label (SINCE THERE IS ONLY ONE!!!) and I could expect to receive the replacement label in 4 to 6 weeks and they were sorry, but there was absolutely NOTHING they could do about it. So as my year old washer sits for over a month, Im going to the Laundromat each week. We should have received the new serial number on August 6, 2015. So it’s taken almost 2 months and my label is close to two weeks late. To date I have not received my serial number. I tried to use MAYTAG chat, dont bother, they said they couldnt help me. I needed to call in. So I emailed Maytag today for their support services to tell me WHEN I can expect to receive my new serial number label. I bought this through hhGregg. Check your Maytag washer. IF THE SERIAL NUMBER AND MODEL NUMBER LABEL ARE INSIDE THE DOOR, CHECK TO SEE IF THE INK IS COMING OFF THE MACHINE LABEL, and order a new one NOW if it is, or you will not be able to get your washer serviced. Do not put new label back on the inside of the washer door. This is just unbelievable.

We first purchased a Maytag Neptune washer and dryer set. We loved them. Had them for 15 years with no problems. When we decided to get a new washer and dryer, we were loyal to the Maytag brand. I was immediately drawn to the Maytag Bravos XL due to the extra large capacity. What a mistake! This washer and dryer pair take more than two hours to complete a single load of laundry. It often takes more than one wash to get clothes clean. If you wash an extra drum large load of laundry, often times there is not enough water and agitation to even get all of the clothes wet. I have a one-year-old boy and a six-year-old boy, their clothes get very dirty. This washer Does not get food off of my one-year-old’s bibs. And my six-year-old’s clothes come out looking as if they haven’t even been washed. What a disappointment! My husband and I are going out today to purchase a new washer and dryer set after having just purchased these Maytags in April last year. What a waste of money! Please include me if a class-action suit it’s taken.

Because of the power of advertising, we replaced every appliance in our home in 2005 with Maytags. Since then, weve had minor problems with the stove and dryer, many problems with the dishwasher and washing machine, and complete failure of two Maytag microwaves, the last one was only two years old. The washing machine failures resulted in major flood damage two separate times due to two separate failures. Our refrigerator, model MBB2256GEW, has yet to let us down, however, since new it makes loud snapping noises that wake us up at night. It sounds like someone banging two large sticks together. Fortunately, I can repair most of these issues when they arise, but Id much rather get some rest like the Maytag repair man...

Constantly does not clean clothes, always out of balance, codes constantly come up, only 2 1/2 years old and already rusting out. No matter what you do this washer does not want to work. Has special cycles for bulky loads but try to wash 7 towels and it will dance all over floor then shut down with an unbalanced code and you have to unplug to reset then wash towels again but not use spin and have to wring out towels by hand. I cannot believe the Maytag company has not recalled this very expensive pile of junk, and their service department is very rude and not helpful at all.Also as soon as you call an appliance repair company and tell them its a Maytag Bravos they say we do not fix those, do yourself a favor and junk it and buy any other brand. I have 3 kids now grown so we have bought about 5 washers over the years and when we saw that this was supposed to save water and energy and do bigger loads we were sold. Big mistake! Whatever you do never buy any appliance from Maytag. Products are garbage, service is nonexistent, and the cost will make you boil.

I bought a Maytag Centennial Commercial washer, 3.8 cubic feet, Model # MVWC425BW on September 17, 2014. My clothes were never clean and barely wet. The machine took almost 2 hours to do a load of clothes and they werent even clean! I bought the 3-year extended warranty through Lowe’s. Three years and 8 days later the machine stopped working. Serviceman came out and told me the washer was fatally wounded. He said the transmission failed. He also told me the replacement part would be $400.00 and that it wasnt worth it. He said these machines are junk and Maytag has had all kinds of issues with them. So Maytag knows these machines fail and yet do nothing for their consumers. Maytag, you will only ride on your name for so long; consumers are catching on. Maybe back in my Moms day you were the go-to brand but Im afraid that ship has sailed. Ive always gone with Maytag but now I question that choice. I came on Consumer Affairs page to see what brand I could buy other than Maytag. Seems Kenmore gets high marks.

This is the worse washer... As many other have complained I have the same problems. This washer it will not fill with water ever. It doesn’t rinse clothes or clean them as I’m use to the old washers doing. From day one I noticed the water does not fill in the tub and wondered how can the clothes be getting cleaned properly. Getting a F51 code and after going on YouTube and checking for problems it seems to say the same code after it works for a bit. This is the worse appliance I have ever purchased. I am so frustrated and will never purchase a Maytag anything again. Never did in the past up to this one and never will after this one.

MDB7749AWM1 more Maytag corporate garbage! I bought this dishwasher since my last one, Whirlpool, gave out at three years (garbage motor from Korea) thinking this would be a quality product made in USA. Well after about 6 months into usage and under warranty, the circuit board went out! The repairman assured my wife that it was rare to replace it on a Maytag. Now 9 months later, out of warranty, the circuit board goes out again! I know what it is, I can fix it, but will Maytag work on fixing to get a better circuit board? No! The US government is a puppet to all these companies that keep getting bigger and fatter! I say buy foreign products! Enough of these fat companies buy the competition out and giving the US public no option. Preston E. Tucker said it best: You let the big guys push the little guys out of the game and you will end up with garbage for products! Do yourselves a favor, buy Bosch, LG or Samsung. I know their products are not better but just maybe, someone in these corporate offices will see that to sell in the USA, you have to sell quality again!

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

I purchased a matching set of Maytag Neptune washer and dryer about 6 years ago and the washer is junk! It sounds like a jet is landing in the laundry room. The repair man said it is not worth fixing - bad bearing. I am not happy!

Dryer needed to be serviced within 2 months. Drum seal fell out. Service was no questions asked. Fixed promptly. Washer works fabulous. Gets clothes clean. Surprisingly quiet. You do need to keep up to the sensors on the dryer. Must be wiped with rubbing alcohol to keep performance.

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

I purchased a Maytag Washer Model MVWB765FW in April 2017. Its transmission has failed, makes lot of noise. The cost to repair is about $500. for Parts and Labor, under the 10 year Limited Warranty, as advised by Factory Service. I am better off buying a new Washer for that cost. The days of Maytag reliability are gone. I would not recommend this product to anybody.

All of a sudden, the lid lock light is flashing. The washer is only 1.5 years old!

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

Thanks for the other reviews about the control panel problems... I too have the same issue with the short circuit. My Maytag dishwasher mdb7749sam1 was installed in January 2013. I spent an hour on the phone and the chat... HERES THE SOLUTION: When I told them the machine started in the middle of the night on its own, it became a safety issue. I have all the same problems as everyone else, flashing lights, the washer does not properly respond to the input from the control panel... I was told that even though it was out of warranty, as a gesture of goodwill Maytag is sending out an authorized repair service to fix whatever is wrong at no cost to me at all... Tells me that there really is an underlying issue. Anyway best of luck to anyone else in the same boat. I rated them as a 3 - not happy that this machine failed and I wont buy another, but they seemed to jump on fixing it...

I am writing for your assistance with an ongoing problem that I am having with my Maytag Series 2000 front-loading clothes washing machine. I am, frankly, astonished and frustrated beyond any means of coping with the response I have gotten from Maytag about the lemon washing machine that was sold to me. As I have never before had any sort of reason to complain about any major appliance purchase (nor about any car or house purchase), I’m not yet sure of what avenues are available to me. It seems prudent to inquire of your office before getting a private attorney to help me with this. The following is my situation:First of all, I am asking for a replacement washing machine. I am clearly saddled with a lemon.On or around December 2010, we purchased the Maytag Series 2000 washing machine from Cedar Appliance of Medford, MA. Within the first several months, the washer started ripping, shredding, and putting holes in our clothes. This did not happen during every wash cycle, just sometimes. At the time, we didn’t know if it was the washer or the (also new) Maytag dryer that was causing it. After living with this for some time, we decided to call Cedar Appliance for service. Cedar came out several times to look at the machines and they couldn’t tell what machine was causing the holes. Eventually, I started examining every article coming out of the washer to determine which machine was causing the problem. Over time and many visits later, Cedar Appliance referred us to L.A.R. Service of Wakefield MA, which they called Maytag service.L.A.R. Service came out and looked at it. They said that we were missing a part. They ordered the part and installed it and said everything should be fine. They also sold us an extended service contract. I am still having the exact same problem with the machine. Today I called L.A.R. and they told me that I had to call Cedar to get an authorization for service. I called Cedar and they told me to call Maytag. I called Maytag and after spending an inordinate amount of time recalling the details, the service representative told me that I could pay up front for an extended warranty and they would send someone out. I asked for a supervisor. I got Kitty. Kitty told me that Maytag would not replace my machine, which is clearly a lemon because I hadn’t yet had enough service done on it. I explained that I have spent hours calling for service, scheduling service, waiting for service, supervising service, and paying for service. She explained that on only one service call did they install new parts, so I needed more service. So, I should have demanded new parts on each of these service calls so that I would have earned some credibility for my lemon machine?The fact is that my family and I have lost hundreds of dollars on torn and ruined clothing caused by a new washing machine! After the boot was installed, or replaced (I’m not sure exactly what was done), we are experiencing the exact same problem. When the L.A.R. Service people left last time, they told me the problem was solved. It wasn’t. This is not normal. This is a lemon machine.Its one thing to have clothes destroyed, but what is extra frustrating is that I never know when the machine is going to destroy an article of clothing. This past Friday, we were preparing to go out of town for our daughter’s basketball tournament. I took the clothes out of the washer on Friday evening to discover that one of the blue uniforms was destroyed. There was no time to replace the uniform and my daughter was out of luck. This means that I cannot put an article of clothing into the washer that I absolutely have to have. I can’t live this way. This is a relatively new washer that should last 20 years. Right now, I can’t wash any important article of clothing. I’ve been told before that it was all set. Kitty has L.A.R. coming again this Wednesday to repair the machine. What am I supposed to do when it’s repaired? Put a uniform jersey in it? This is a very brief description of the experience I have had over the past 1.5 years with this new machine. The hours, money, disappointment, and utter frustration is more than I can describe in an email. I have attached three photos of recently destroyed items. Unfortunately, I threw away tens of items several months ago when L.A.R. fixed it.Is this unbelievable? Or are my expectations too high? Is this really what Maytag/Whirlpool has in mind for customer service? Is this really what they mean by standing behind their products? Why wouldn’t or why shouldn’t Maytag replace this machine? How much more time, money, and tears is a customer expected to spend and endure? How do I regain peace of mind and quality of running a household? Am I supposed to toss this machine and buy a new one? Believe me, that’s what I will have to do if I can’t get relief on this problem. There is no way that I can go many more months with this headache. In many ways, buying a brand new machine would be worth the peace of mind, but I am trying to make sure that my family, as consumers, are treated properly. It is also the principle of the thing. Please advise on any remedies available to me here in Massachusetts and please let me know what additional details should be provided and to whom.As an aside, Maytag/Whirlpool does not seem to be doing well with their reputation on the internet regarding customer service.

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

I bought this washer brand new in 2011 for $650. I had bought a Maytag washer before in 1967 and it was still running in 1995 when I gave it away. Considering my first Maytag lasted me nearly 30 years (Last I heard the machine was still running in 2005), I never thought my new Maytag would give me any problems, until it was at least 10 years old. (I did know Maytag had been bought by Whirlpool but didnt expect any difference in quality). Boy, was I wrong! After using it for a month the machine broke down and it had to have the clutch and gear box replaced. Last week July 2016 the machine broke down again. It was the internal computer (referred to as the electric control unit) a printed circuit board that retails for approximately $300 (A ridiculous price given that much more complicated laptop and tablet computers today can be brought for $100, the circuit board should retail for no more than $40).With labor the repair bill came to $550, which was nearly as much as a new machine and did not justify the cost. Supposedly the electric control is susceptible to current surges and power outages. Given that this is the case, it makes no sense whatsoever that a machine billed as eco-friendly would carry a part that will doom it to the junk pile because of a power surge or outage and does not carry a surge protector. After learning of my experience Maytag called me the next day and offered to sell me a new Maytag at a discount price, which of course I flat-out refused.I would never ever again own a Maytag appliance or one made by its new owner (as of 2005) Whirlpool. With such susceptible electric units these appliances will sooner or later result in electric fires that will end the life of its owners. The US govt needs to protect US citizens from these predatory companies that make over-prized, throwaway products labeled as eco-friendly that are potentially dangerous. My advice for anyone that is thinking of buying a Whirlpool or Maytag washer dont do it. For those that already own these machines do not run them without a heavy duty surge protectors. It is not worth your life.

I have had this dishwasher less than 2 years, Maytag model # MDB7749SBM2. The control panel started acting up, it would not let me select a wash cycle, it would select its own and I could not change it. After reading these reviews, I took off the control panel and discovered the wires which are encased in a plastic were all darkened and messed up. I will try to replace it on my own but if I have to I will buy another brand as this dishwasher hasnt really cleaned my dishes all that well to begin with.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

I purchased a Maytag Bravos washer and dryer pair in 2009. Over those 5 years I have had at least 8 shirts come out of the washer with tears in the armpits. First I thought it was my armpits destroying the cloth. Then I thought it was cheap cotton (all my shirts are 100% cotton) from foreign manufacturers. Ive had two shirts destroyed this week, this mornings was really thick material. Usually when I remove clothes from the washer, they are entwined and twisted. Consistently when I wash any load including a towel or two, the washer becomes unbalanced. My clothes often have a foul odor after washing. My theory is that the lack of a center agitating spindle is allowing the clothes to tangle, and not really cleaning them. I have to use the extra rinse setting or the clothes come out covered with soap suds. In summary, Im not happy with this washer and will never buy another Maytag appliance. Im also not sure the high-efficiency technology has had all the kinks ironed out.

1st service call about 2 years after we got it. Put around $200 in it. Now broke down again. Service tech quoted $475.00 to fix it. So it was basically totaled after around 6 years. Nightmare kept getting LD (long drain) code. After hours of research I finally called service. Would not drain so I had to wring out a whole load of laundry and bail out the water by hand. Miserable experience!

Just when you think that youre able to do laundry. First, comes the musty smell. So, you clean cycle your HE machine using only the cleaning product directed by the manufacturer. Then, comes the pump being stuck on. Like it still have to drain yet your clothes are soaked but you heard full force of a good drain. Poof. Unplug and kick it. Look on YouTube and discover you should take it apart and clean out some obscure puddle holder & look! You discovered where the sock monster lives...its gross. Going to start my own business (125.00) to clean these things out. Hopefully not get some kind of fungus from the grossest mold ever. Its Maytag not a Home Depot issue.

I purchased a Maytag Dishwasher Model MDB7749SBM3 in January of 2014. I have had issues with the control board for the past month: lights come up at random; it takes 3 to 10 trials to get it to start and now it is dead. After reading many reviews on this site, I now understand what the problem is. I called Maytag customer service and they wanted to schedule a service call at $98 just for the diagnostic. I asked the Maytag associate whether the control panel issue was a common problem and she said she would research that but did not give me an answer. I am totally disgusted by this company!!! I would be happy to join a class action suit.