The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

I purchased a Maytag MDBH979SAB0 dishwasher from Home Depot two weeks ago for around $600. I got it installed and it would not turn on. I contacted Maytag and after a few questions, she stated that they would have to send a repairman. After a few days, the repairman arrived and said hed never seen this model before but that we needed a new control panel. After waiting a week with no work, I called Maytag to get an update. The control panel is out of stock and could be a while - they are trying to find one somewhere around the country. They refused to send a replacement dishwasher, even though this was brand new. Their policy says repair, not replace. Dont take the chance purchasing a Maytag dishwasher.

1 year 4 month old fridge went out. Waited a month for part/repair. No help from customer service. $1200 fridge, $700, lots of angry calls, no luck. Customer service is horrible. Will never buy Maytag again. Someone suggested to take it to small claims court. Has anyone successfully done this? Any advice how to get my $700 back? Please email me **. Thanks.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

I have owned my Maytag washer for approximately five years. Ive always used the recommended detergent and religiously used the tabs to clean the machine when it was required. I have never abused the machine by overloading it, using too much detergent, etc. It is now coming up with an LF code. There is no one in this area who does repairs and if I do find someone Im sure theyll want some exorbitant amount to come all the way out to the boonies to give an estimate and the repairs Im sure will be hefty. I take very good care of all my appliances and expected this machine to last much longer.

I bought a Maytag Neptune top load washer in 2002. It worked fine (with the exception of smelly clothes) until October 2011. Since then I tried replacing two new clutch assemblies, a new outer tub and bearings. What we were just told this week: it needs a new spinner. Finally throwing in the towel and taking the $500 credit from Sears and buying a new washer. And I can guarantee I will never buy another Maytag product again!

We have had this washer/dryer stack up for about 2 years now. Not long after it was purchased from Best Buy, it started smelling like mold, even though we were doing everything possible to keep it ventilated. Best Buy employee said that service was not covered by the warranty that we purchased, so they suggested we YOUTUBE some ideas on how to get rid of the smell. They said it was a common complaint for front load washers. We have tried Affresh, hot water and bleach, hot water with vinegar and lavender, etc. Nothing is working. There is mold on the plastic inside the washer door and the stench is horrible now. You can smell it when you walk into our home. I believe that stench is the reason we are all having respiratory problems, allergies, etc. I just dont know what to do anymore. Really frustrating!! These appliances cost a lot of money.

First Maytag washer we bought in 2003, worked flawlessly for 14 years, bought a new one in 2017 only because my wife wanted a bigger washer. Bought a Maytag top load MVWB765FW0. What a big mistake. In less than 3 years it has failed already. The water inlet valve went bad. Maytag offers no tech support because they want to charge you with a service call. I found out what was wrong by researching the problem and error code online and bought the part for $55.00 and fixed myself instead of them charging $100.00 just to show up at your door plus the part and labor. A washer failing in less than 3 years is totally unacceptable and I will never purchase another Maytag/Whirlpool product ever again. Someone needs to wake up at Maytag.

We bought the Maytag Aqualift cooktop about a year ago & are continuously dissatisfied with it, for several reasons: 1) the cooktop is a huge nuisance to cook on. The burners are either raging hot (causing boil-overs), or too cool to simmer. The boil-overs then require much cleaning with an expensive cleaning agent. 2) the oven, whether you use regular or convection, underheats - so you can’t tell how long the cooking or baking process will take, & you have to monitor the cooking process. 3) the so-called self-clean is a joke; the oven will not be clean unless you crawl inside & clean it manually. Overall, I’d prefer to toss this range in the trash. I’m a good cook, but I get angry every time I use this expensive, poorly- designed product.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

This washer has no agitator post and doesnt seem to clean as well as ones with agitator posts. I have heard that they are easier on your clothes though. The dryer works well enough, but I believe the control panel/motherboard needs replacing. The signal sounds even with the dryer turned off, which is startling to my dog and me. I reset it by flipping off the 220 breaker in the garage and leaving it off until the next time I do laundry!

We too were having a water leak from the French door freezer and a sheet of ice under the freezer drawer. The repairman came and told us that it was a common problem with the French Door fridge and an easy fix. Maytag has a new P type defrost hose that doesnt freeze up. He changed the part, $149.75 bill, and no more problem. Should Maytag have let consumers know this was a part that was failing? Yes, definitely. But at least the fix was reasonably cheap.

I purchased this washing machine from Home Depot in 2012. I am amazed that it lasted this long after reading the reviews on here. It will not drain water, it will not spin. I see many customers bought the same washer and are having multiple issues. When will Maytag recall these machines? Overpriced and unfair to consumers to sell something that is broken or not reliable.

I have ALWAYS bought MAYTAG since the 1970s. But MAYTAG is no more. Whirlpool bought them out. I have an HE (first mistake)... HE... will go away just like low flow toilets did!!! You cannot wash clothes in 4 of water. I bought a top loading Brazos XL for $1100 (second mistake)... Have had it just over a year! I should have returned it but did not. Huge mistake (#3)... Repairman told me to get rid of it as fast as I can. Will eat me up in repairs. Now needs repair again for another NEW issue... The fill sensor does not tell the machine to load the proper amount of water. Now I cannot clean washer, tried three times last night. I am beyond upset. Repairman said buy GE! You can bet it will NOT be High Efficiency!!!!!

I researched gas ranges for a few months before choosing our Maytag gas range - it was on sale when we ordered it and it arrived within a couple of weeks. We wanted to buy local and were successful with price matching the sale price. I would recommend this range as it functions great and we totally love the larger oven door.

Not yet two years old, my Maytag Bravos dryer stopped working. When I called a technician to see what the problem was, he told me that the circuit board was burned out and it would be $500.00 to replace. I then called Maytag to find out if there was a problem with this machine and was told no. This apparently is a lie as there were numerous complaints when I checked the internet. I have five Maytag appliances and at this point, only one has not caused a problem. Maytag is not the company of the past when if you had a Maytag, you had the best. The repairman no longer sits around with nothing to do.

I bought a Maytag Gas Range in January 2010. In January 2012, the wiring caught fire, and now, the oven is unusable. Maytag was not very helpful in our loss of money and product.

Buy this washer! It has the best features! No matter what the setting, your clothes will come out as dirty as you put them in, only with even more odor! I just cannot believe how many different settings they managed to program into this washer, each one delivering the same miserable results. I am so happy that I spent so much money on a washing machine, that in some cases, doesnt even get my clothes wet. Truly amazing technology!

Please do not buy a Maytag washer top loader. It does not get enough water and it does not clean your clothes. It is the noisiest cheapest made machine out there. If you have kids you really need to bypass this one. I have had this for 10 months and its only me. Please especially if you have children stay away from it. Im the most unhappiest camper Maytag ever had.

I bought this machine in 2013 and within a year it had stopped going through any cycle. It turns off and I either have to restart a cycle or set the machine to rinse/spin. My clothes do not seem clean so I have begun handwashing them before putting them in the machine. I retrieve clothes and find some clothes dry. My towels have worn spots and threads pulled out. I cannot wait till I get a new washer because I am going to put this Maytag Bravos in the backyard and take a baseball bat to this hunk of junk.

My 20 yr old Kenmore washer broke last month so I replaced it with a Maytag I bought from Lowes. I wanted a simple washer that would maybe last 10 years. The Maytag has a sensor for everything. So you can’t fill the washer, it determines how much water to use and it never fills enough to cover the clothes. It doesn’t agitate really. It’s more like a slow on & off movement. It does everything in an on & off way. The water fill goes on & off, it “washes” on & off. Even the spin is a spin, slow to almost stop - spin again - almost stop - spin again. It also stops filling if you open the lid, I tried to let some water fill before adding clothes (so the liquid detergent could dilute a bit) but every time I opened the top there was no water in the drum, I heated the water running and the drum was wet but it wouldn’t gill at all. I think it only puts water enough to “sense” the clothes have been soaked. I will call Lowes and try to return it.

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

I purchased my 10kg commercial Maytag dryer in March 2015 and started using it in May 2015. Within two months the heater had broken. I contacted the people I bought it off and it turned out I had to contact Whirlpool. It took them 8 weeks to get my dryer going again. The dryer broke down again in November. This time it was a sensor. Again I had to contact Whirlpool, it took them three weeks to get it going again. Being a care home the dryer is essential to our business. We were led to believe when we took out the extended warranty that the dryer would be fixed within a week. I will never purchase a Maytag again or anything to do with Whirlpool.

After seeing all the bad reviews about Maytag I decided to write my review, we purchased a Maytag washer and dryer 1990 when moving into our new home, and we still have the same set. Now it does not have a motherboard which I feel today is the major problem with most appliances. Get away from the motherboards. Turn the machine on and off when its supposed to, or let it run its Cycles. Dont overfill, because this causes wearing motor parts. The dryer belt wore out on the dryer but that was an easy replacement. Im a woman of 64 and get it myself. Maytag I hope that you get back to the plain ol simple washer and dryer because mine is probably going to wear out which I hope not but I would so love to get the same set I got now.

Purchased Maytag front load washer model MHW6630HW from Home Depot. Machine was installed 9/15/19. From inception we had issues that have escalated. Machine leaks and makes strange hissing sounds. Home Depot has no record of the purchase in their website now. We tried to return it within days. We contacted Home Depot executive offices and they keep sending Paradise Appliance repair. The repair people do nothing and keep saying we have to come back again for you to be considered for replacement. Home Depot is dragging their feet and we are concerned about the six month deadline. The Maytag does not do an effective job washing and clothes comes out wrinkled. Concerned about the sporadic leak getting worst and doing damage to floors.

I own an iron in case a guest needs to use it but I seriously havent ironed in over 20 years. I moved into a home in November and the appliances stayed with the home. I am systematically destroying my clothes that I always washed and dried but NEVER IRONED. They come out of the Maytag washer already wrinkled. I try to unwrinkle them in the dryer. I took 2 items to the dry cleaners to see if they could steam them but no results yet. What gives Maytag???

My original GE dishwasher that came with our house finally crapped out after about 8 years of use in 2007. Bought a Maytag from Home Depot for around $400. Dont remember the model number. It worked okay but then in the middle of 2010 we got a letter in the mail saying our machine was being recalled because the heating element might catch fire (!!!). The recall gave us the option of getting it fixed or getting a $150 rebate. We chose the rebate option so we trashed this dishwasher and went back to Home Depot to buy another one.We found a very nice Maytag with the stainless steel tub and the racks with the lifetime warranty against corrosion (which was good because our previous Maytag had started to leave rust on our dishes because the plastic on the tips of the rack tines was starting to come off), model #MDBA979AWB1, serial #FY2501885. The one we found was a no-box display model but it had all the accessories with it and still had the factory warranty. We got it for just over $300 and with our rebate applied we were out the door for under $200 including tax. I installed it myself and didnt have any issues for quite some time. My wife and I were both very happy with how clean the dishes got!Now, last night the dishwasher wouldnt start. I checked it out this morning, made sure it had power and was able to get some lights on the control panel to light up but still couldnt get it to start. Looks like Ive been victimized by the control board as most of these complaints have said. I guess I should consider us lucky since ours seems to have lasted longer than the average 18 months to 2 years. Will be contacting Maytag and Home Depot to see what they can do but after reading all these negative reviews Im not hopeful.

Yesterday I was using my washer (small load of clothes), I was with my baby in the laundry room when suddenly there was a horrible noise and the door of the washer opened, he hit my back, something fatal could have happened. I do not know how it happened but a piece of concrete was inside the drum. I do not want to imagine what would have happened if that piece came out and hurt my baby. I spoke to the company and explained what had happened to me, but they do not want to be responsible for what happened because the washer is in Tijuana (border with San Diego), I bought the washer in Pirch San Diego California in 2015. Maytag United States is responsible for this defect. Dont buy this model:mhw8100dc extra large capacity washer with steam and powerwash® system-4.5 cu. Ft.

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

Purchased the Maytag Bravos upon recommendations from Lowes and Home Depot to replace a 20-year Kenmore that finally died. Since the Maytag brand was always considered to be the top of the line washers, we purchased the pair. About a week ago during the spin cycle I thought that a 747 was taking off in our laundry room. Called a local appliance repair service who said that there had been numerous issues with the Bravos series and to call Maytag to inquire about a recall. After 45 minutes on the phone with a very sweet naive young lady, she told me that the new models did indeed have a 10-year limited warranty on parts. However my 3-1/2 year old washer was not grandfathered into the warranty. I could (a) pay the $150 service charge to have someone come to inspect it or (b) buy a new one. I will be purchasing a new one but it will not be a Maytag or Whirlpool product. Now we know why the commercial for the Maytag repairman is not running... Hes now very busy working on their broken products.

We bought all new appliances for our remodel. I wish I could return this dishwasher. It has a problem with the door staying closed. I added images of how we are able to make it work. A service person is coming by tomorrow to put a new latch on it (I read several reviews saying the latch is messed up). So I made sure the service person is coming with the part. I called Home Depot when the problem started (used for up to 5 washes or so). And Home Depot wont return it! I called Maytag and they tried selling me an extended warranty and I asked what about the 10 year warranty the machine is supposed to come with? I guess thats a joke as the lady told me I should of read the fine print. So buyers beware! I wish I would of know about Maytag. I would have about a Samsung instead!!!

Bravo Large Capacity Washer with Optimal Dispensers - 4.3 Cu. Ft. - The washers shortest cycles take at least an hour (not including having to do another spin/drain) and uses such little water that I have to use the extra rinse cycle on most loads. The washing machine is VERY hard on the clothes; towels (which I feel are pretty hardy) have been destroyed. Today the machine stopped draining/spinning completely and smelled like it was burning. I called the warranty number and was told it would be a week until someone could come out. When I tried to escalate a sooner repair date the manager Jessie refused to assist in any way insisting there was nothing he could do. I spent the morning calling my local repair shops and was able to find a Maytag warranty repair person to come out the same day, but had to call the warranty number again and have Maytag place the request. Sorry for the long post, but this washer is the WORST purchase I have made. The warranty experience was very unimpressive. I will not be purchasing anything from Maytag/Whirlpool/Jennair ever again.

I can honestly say that my Maytag refrigerator is indeed the worse appliance that I have ever purchased. This is how it rolled... I bought a new Maytag stove, frig, microwave, and dishwasher in June of 2006. Here is what I am now dealing with... the frig went on the fritz 2 years ago (warranty expired). The problem being the freezer would not automatically defrost. Because of this the coils would ice up and this prevented the cold air from moving from the freezer into the frig part. Things remained frozen in the freezer, but everything became warm on the other side, the frig side. I had it repaired about a year and a half ago to the tune of $165. Then about 6 months ago the problem reoccurred, but instead of paying for another repair I figured out that if I used my blow dryer I could defrost the ice from the coils on my own.Unfortunately, the problem reoccurs more frequently now and I have to manually defrost the coils almost every week. This past weekend things finally came to an end as no matter how many times I manually defrosted the coils, it would be fully iced up again with an hour or so. Also, all the time it is acting up it just sucks up electricity, and I have notice a spike upwards on my energy bill. It must be related to the frig. So, I bit the bullet and bought a used frig on craigslist just to hold me over until I have time to do research on what appliance brand is indeed reliable. I should of done this before I bought my Maytag appliances from Home Depot. As far as my other Maytag appliances, here is their current condition. Microwave about the stove: the handle broke off a little less than 2 years after purchase. Stove: now has rust on the front of stove, at the bottom of the stove which is a pull out drawer.Dishwasher: not working at all. The start button doesnt work. Normally, you just push the button and a green light comes on and it begins the first cycle. This is no longer happening and no green light comes on. Refrigerator: Took it to the dumps this morning to be recycled. Cant believe it, all of these appliances are nothing but crap and I will never purchase another Maytag. I have shared my experiences with all my family and friends and have encouraged them to avoid Maytag, as it is not even close to being the product it used to be. Another piece of junk coming from somewhere other than here in the USA. We lose jobs here in the US, and then end up buying the goods from another country that makes inferior products. How stupid can we get!

Bravos washer is 4 years old. Started making an extreme amount of noise during the spin cycle. Had a repairman look at and showed me the bearings and area under the tub. $400 plus in damage due to bad bearings, rust to bottom of tub and surrounding area. Four years for a high-end washer is pretty bad. Needless to say, I will buy a new unit and would NEVER recommend a Maytag Bravos appliance.

The performance of the refrigerator is disappointing. It was difficult to find someone to repair it when the freezer fan motor went out. It makes noise, shelf space is insufficient. Temperature mechanism often doesnt work properly.

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

Bought Maytag Electronic Washer and Dryer on Feb. 7th 2020. On July 10th control board went out in dryer. 3 weeks without a dryer and hanging clothes in 112-118 degree weather in Arizona. I am 77 years old and too old for this. Dont buy Maytag!!. Had Whirlpool Washer and Dryer for 22 years. Never a problem, regret buying a Maytag.

I am not complaining at all about my dealer. I am complaining that I also am like the many others with the French door fridge/freezer. The bottom of the freezer freezes up and water pours all over the floor. I thought that Maytag was a good appliance, but also had problems with the pump and drain on my washer. Both of these are only 2 1/2 years old.

Maytag Dishwasher model MDBH989AWB3. The dishwasher was purchased at Home Depot March 19, 2010 in Hollywood, FL; delivered to our new home April 16, 2010 in Brunswick, ME. My complaint is the exact same complaint as the previous 28 complaints! I think the reason our unit worked for 6 yrs is because it was in use only 6 months a year. My experience: you make your selection, two lights come on, you press start, but nothing happens. You think this is a simple repair. You read the manual and try their troubleshooting advice, but to no avail. When you contact the company, they tell you that this is going to be an expensive repair, probably over $500. You contact Home Depot who want nothing to do with you or your dead dishwasher. Their advice: contact the Maytag company. You contact local appliance repairmen and they will repair it at a cost of over $500. You offer the unit to the repairman for free; he declines. He suggests you check the online Consumer Affairs site. It is on that site that you realize the dead dishwasher belongs where one brings other dead things: the dump. I will NEVER buy another Maytag product. I would suggest no one else does either, unless you want to practice your skills in dealing with frustration or you want to throw $693.40 to the wind and watch it flit away helplessly. Thank you for reading this.

I purchased a Maytag washer-dryer combo in late July 2014. It wasnt until early August that we actually used the washer. It worked fine the first day, but the next day it would no longer fill. After following all of the troubleshooting instructions, I called Maytag to schedule a repair. They said they would locate an authorized tech to make the repair. I called back the next day and was informed that there was no repairman in my area and they would contact a service that contacts local repair techs. A few days later I called back to learn that they still could not locate a repair tech. I live near the New Mexico/Arizona border, and asked if a service tech could travel from Tucson, Arizona and was told that they could not cross state lines and, at that point there was nothing else they could do. They claim that I live in a remote area, but I reside near a major US Interstate (I-10). I will be filing a complaint with the BBB and my states Attorney General. It is now late October and all of my efforts have been ignored. I am totally disgusted with Maytags customer service.

Maytag washer MHW5500FW had service just a month after purchase and still a year later the washer has problems spinning using direct drive. Even a few towels are soaked when cycle is done or errors out and must be restarted. Most of the time the washer has to be cycled on spin to remove water from soaked items, not just a simple bath rug, towels, bed sheets. Almost anything has a problem spinning. Had to purchase another year of service coverage as I dont trust the washer will last. Soap dispenser needs to be diluted despite using correct soap, per service tech advice which triggers sensors to shut down. Machine looks good but not ergonomically designed without the stand as you can easily lean over the washer and turn on and off accidentally. Same goes for the matching dryer, also can easily set off the on pause and on/off button. Dryer works great other than that.

Neither appliance (Neptune dryer and washer purchased in 2006) was worth the price paid. The dryer drum actually cracked and the washer repeatedly gets hung up on 3E. I called about the dryer and got an Oh, well response. “We dont know whats happened to that dryer.” What happened to both appliances is that they were used for their intended purpose. I do laundry for my husband and me. Is that too much for a Maytag? Customer service is equal to indifference. So much for Neptune. And thanks for standing behind your products. What is the life expectancy of a dryer drum anyway?

No adequate response from Maytag. Unsafe washer. Will be taking this to consumer protection as my scrubs are coming out of the wash with blood etc. left on the articles, even with bleach used. Very serious for all concerned. If you have someone with shingles or any other transmittable skin disease in your household, do not use this washer.

Maytag, you are still trading on your good name but that will not last! I owned a Maytag, agitator style, for 20 years and it was still running just fine when we built a new house. I thought it would be wise to buy new appliances for my new laundry room so I chose the beautiful and expensive Maytag Bravos XL. I regret that decision. The washer lasted 4 years and began to have problems draining last week. The liquid that stayed in the washtub until the repairman could get here was so foul smelling! He came back today to replace the drain pump and now the washer is showing that the interface and CCU are not communicating. So now we are ordering another CCU and I hope this fixes the problem. I agree with all of you who say you will NEVER buy another Maytag again. Maytag, are you listening?

Worst experience of my life!!!! Don’t buy a Maytag washer!!! It’s agitating our clothes dry. Putting holes in clothes. We bought a warranty that’s pretty much useless. They will not replace. Only fix parts.

Model MDB7749AWB2 Dishwasher - we purchased this dishwasher 3 years ago on 12/23/2011 and it appears to be falling apart. We have replaced two thermo fuses, one door latch/switch and now need the front control panel and handle because two mounting locations for the six screws have broken off. I truly expected a much longer product life than three years when I purchased a Maytag. So much plastic in crucial high stress areas must have slipped by the engineering folks. Or was it just cost cuts. I believe it will be a long time before I consider a Maytag product again based on this one. Thank you.

Oh my god, I feel your pain, folks. My mother is sick in the hospital while I try to maintain my house with this totally POS refrigerator!! 3 defrost cycles to remove ice and now the service guy tells me that compressor is shot, 6 week back order for parts!!! Just two years old!!! Also had the same water overflow issue to boot 1 year after getting it. Maytag (whirlpool)- youre killing me!!!!

Brand new top of the line top loader washer. Lid locked mid cycle and couldn’t open it. Called Maytag. Sent a repairman out to fix. Three trips later, 5 parts, and over four months later, still broken. Unable to use washing machine. Been going to laundromat to do laundry. When speaking with Maytag, all you get is a sorry. Now I’m waiting on another part and then schedule another appointment to have guy come install. Maytag would rather replace every part, one at a time, than send a new washer. It is beyond ridiculous for a new washer to have to have all of its parts replaced. It’s a hunk of junk and Maytag will not stand by their product. Worthless company. Will NEVER buy another product from them. Their washer and their service is so far below standards, it’s criminal.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

I bought a fridge from Home Depot. It was on sale and not a Maytag. Somehow they delivered a Maytag. I am over-the-top happy with my fridge. It keep things cold. It is roomy, It has separate temp controls for the freezer and fridge. The bright LED lighting is wonderful. It is energy efficient. It is easy to move around when I need to clean under it. It was delivered right away.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

Maytag washer Model #: MVWX655DW - I purchased this machine at Lowes in May of 2016. Always was a loud machine but seemed to work ok. In April 2018 the machine stopped working correctly. The spin cycle would lock up and not finish leaving clothes soaked. Called Lowes and waited for their repairman. He came and said it was the clutch and drive motor. Repair is over $400. Machine is worthless. Huge mistake. Never buy a Maytag. I called Maytag to see if they would warranty it. They basically said, Sorry only a one-year warranty on it. I told them the reason I bought it was it had 10-year warranty on it. They said only certain parts but its the drive motor that is clearly marked on the machine that has the 10-year warranty. I was told, No sorry. What huge waste of money. I am out close to $600 and Lowes only give you a store credit with their protection plan.The credit is not enough to purchase another machine without more out of pocket expenses. I will never buy another Maytag and I would not recommend anyone else does. Their warranty is a huge joke. Their customer service is terrible. Maytag should not even bother sticking the 10-year drive motor warranty on their machines. They do not honor it. My advice do not even consider buying one. You will be out the money and be purchasing a new machine within two years.

Bought this as W/D set brand new from Home Depot. Had been noticing incredible wear and tear on clothes, as things get so tangled up and need to be practically ripped apart before going into dryer. Cycle times are crazy long, up to over an hour in some cases. Doesn’t have a “Speed Wash” cycle. But WORST of all, after less than 3 years, it just stopped draining properly. Tried all the Codes test, etc. Finally called a repairman just to be told repair costs would probably cost more than the machine is worth. $125 to be told we ought to just buy a new washer. Not happy.

I purchased a Maytag Bravo XL from Lowes. Ive had nothing but trouble with it since day 1. I called Lowes and they said the hose that was placed on it was the wrong hose because I cannot use the the BULKY Cycle. Its easily to off balance and shakes the house. Im continuously having to restart it, it just stops and blinks without any codes showing, on all cycles. I paid $1,000.00 for this washer and will not purchase another Washer with sensors. The life span of the digital washers without agitators are maybe up to 3 years, if that. My last washer was a Whirlpool Cabrio Top Loader and it did the same thing. No More for this mom of three children, the older generation of Washers lasted TEN years or more!!!

I grew up trusting and believing in the name brand Maytag. Unfortunately, I wont anymore. I purchased a Maytag MDB7749AWM1 dishwasher from Lowes thinking that I would not need the extended warranty because well it was a Maytag and they just keep working and working for years to come. Not true anymore. 1.5 years after the purchase the control board has gone out. I come to find that hundreds upon hundreds of people have all experienced the same thing. Shortly after the manufacturer warranty expires, the panel dies. By all accounts it is an issue of POOR engineering and Maytag now being produced by Whirlpool. The replacement part is between $150 and $200. Thats about half the purchase price. It is a racket. Companies like this probably think, well if we build something that is going to last and last we cant make money on that. So lets rig it so our stuff breaks right after the warranty and charge half the price of the unit to fix it so we continue to make money either by people buying the part or just going and getting a new dishwasher. Well I can tell you I will be getting a new dishwasher and it certainly wont be a Maytag OR a Whirlpool.

I have had my washer and dryer for 14 months and from day one, my washer eats holes in my clothes. It is always the bottom center front of my shirts. I complained about this and was told it was my clothes. They were either old, or the type of fabric, or too much bleach, etc. etc. Everything was wrong with myclothes except the washer. I purchased a new shirt and washed it without ever had worn it, and when I took it out of the washer, it has holes in the front. NOW YOU TELL ME that is the shirt and not the washer. I have used Maytag for the past 40 years and I never had any problems with the old Maytag washers. This new Bravos is a piece of junk and I am sorry I ever purchased it. I will never buy another Maytag product.

I related my problems with a Maytag Bravos Washer a few days ago. A year and a half after I purchased the washer, it would no longer spin, among other problems. I was persuaded to call a repairman who diagnosed faulty electronic components which would cost me nearly $400 to repair. He confirmed that the washer was poorly built and strongly advised that I replace it. So, after paying him only $25 for a service call (he felt sorry for me), I did some research and bought a top-load agitator washer because the old-fashioned machines actually do their job - they wash clothes! I was duped by the high-efficiency claims, low-water-usage of the Maytag which didnt wash that well when it did work.

I purchased a topload washer two years ago and the plastic lid has been replaced 4 times because it cracks at the hinges. It is obviously a manufacturers defect that Maytag refuses to admit. They come up with excuses blaming the consumer instead of their bad design.

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

I purchased a Maytag electric range model # MER8775AS in Feb 2012. While boiling syrup, the pan overflowed onto the oven door. As I began to clean up the spill I noticed that some of the spill had gotten inside the door on the inside of the oven glass. To remove the stain would require disassembly of the door. I called Maytag and complained of what I called a design flaw and they said, No, its your fault for spills entering the door. They even sent a condescending email to me informing me that if I needed to purchase parts, where I could get them. I designed appliances for years and this is another example of poor quality and lack of consumer service. I AM DONE WITH MAYTAG.

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

My Maytag 2000 has ripped our clothes. This is my 1st front loading set. I looked on the internet and it seems that this is a known problem. Very upset that a brand that I had for 30 years and recommended to others as well has turned into a terrible company. Im a single mom and Im not in a position to replace a washer every year. I trusted Maytag! A recall and either replacement of the parts, or delivery of new part to fix the problem should have been put in place. I wrote to Maytag to see if they will do something to fix this problem.I have the set, washer shakes a lot, but works well. Washer also always has a lot of water left on the door seals folds, terrible design... I will post on other sites to warn other customers. This is not OK, my clothes are destroyed. See pictures. Clothes got trapped in a gap that exists in the perimeter of the opening, where it meets the door. Why is there a gap at all???

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

I love my Maytag washing machine. It have different settings for the wash, also a size load for your washing, and I love the rain cycle. You could do single runs with Downy or extra runs which is great. Especially great if you’re doing blankets and towels you need that extra rains. Great reliable machine. Highly recommended.

We purchased our Maytag 4000 series washer and dryer (Model: MHWE450) in December 2010 from Best Buy. For the first six months or so, we were very happy. We started to notice that the washer was getting a little louder by the month. I checked the level multiple times to be sure that wasnt the issue. Assuming it was just part of how the washer broke in, I just let it go - a bad move! Fourteen months after I purchased the set, the washer flooded all over the floor. I opened the washer and pieces of plastic were all over our clothes. After further inspection, the drain was completely full of the same plastic. I cleaned it all up only to find that the washer tub was so loose that it was banging side to side.I called Maytag to ask for help or suggestions. They basically told me that I was out of warranty and kind of out of luck. I responded that we do a total of four to five loads of clothes per week and that there was no reason that this commercial series washer should have failed after 14 months. They offered a one-time service plus extended service contract. Feeling that I had no choice, I spent almost $400 assuming that I had a fixed washer and a year extra warranty. I was told that someone would be out to look at the washer in three days. Finally, after me pressing and pressing, someone showed up a week later. He put a list together of all of the items that were needed to repair the washer.Two days later, Maytag service calls and says that the washer will be too expensive to repair and they would be giving me a reimbursement for buying a new one. They didnt have an exact amount yet. Two more days later, they finally called me with an offer of around $550 ($250 less than what I paid) based on their research of what I should be able to find one for and directed me to the website. One big catch though - it didnt include the $125 shipping charge. When I called to request for it to be paid as well, they declined with basically a “take it or leave” type of attitude. Not knowing what to do, I called every local appliance store until I found someone that had two in stock. When I went to look at them, I was told that both of the ones that they had were rebuilt because that model Maytag washer had a major issue with the bearing and basically needed to be replaced on all of them.Luckily, I was able to buy the washer and a five-year extended service contract for around $690. So in the end, I paid $799 for the new washer, $400 for a warranty, another $100 to replace the washer, and close to $100 in laundry mat costs for three weeks. I promised everyone that I spoke to with Maytag that I would write a review to share my story and thats why I wrote this. The repair plus warranty is a joke. I like this washer/dryer but will never buy another Maytag appliance again. Next time, I will buy extended service contract from the start.

I built a new home in November of 2013 and filled my house with all brand new top of the line Maytag appliances. Almost a year and a half in, my $2500 refrigerator is broken and all my food is lost. They send a repair man out; and guess what, the warranty is expired. So they wanted me to pay $800+ to have my refrigerator repaired a year and a half after I purchased it. I cant believe they have no shame in sending out products with their name on it that only last 1 1/2 years! I would never treat anyone like they treat their customers. They hold no responsibility. Their name holds no value to me anymore. I was extremely disappointed.

This washer is only two years old and does the wash for 2 people. The control board has broken down and the lid lock did too. Of course the warranty had just expired, so there is no help from the maker, Whirlpool. Save yourself a big loss and dont buy these brands. Mine is going to the dump where it belongs. Thats $500 down the drain. Do yourself a favor and get a Speed Queen.

I purchased the Maytag Bravos washer and dryer in September 2010, before moving to Washington. After a few months, the washer broke and had to have a repairman out twice to fix. It never would wash a blanket without stopping with error messages. He told these were notorious for problems. Now our dryer is leaking and not drying. I checked the vent hose and water and some wet lent are inside. In moving the dryer, I can hear a piece rattling around inside. From research and other posts, it sounds like its a broken pulley system inside. Maytag is junk. Customer service is terrible! I bought this unit during a veterans day sale at Lowes, using my veteran discount. Obviously, Maytag has no problem ripping off veterans or anyone else based on their horrible customer service. I will be actively posting as many negative online posts and videos about my experience on every forum and veteran site I can. They are horrible! Stay away from Maytag!

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

Bought a dishwasher about 2 years ago, through Home Depot. After it was installed, contacted Maytag to let them know that it didnt seem to be working correctly. They sent out a repairman, who looked at the machine, and then told us that with the new eco friendly settings, it would be best to let the dishes dry overnight. It seems that the company and its employees dont know [or care] about the product. Contacted their service/helpline to let them know that the screws on the insides of the latch [on the cover] are NOT screwing into anything, they come loose. Person couldnt find same in his system, finally sent screw, but they were the wrong size and didnt work. Just opened the dishwasher this AM, after washing the dishes last night. 12 hours later and they still are not dry. This isnt eco, this is something that is wrong that Maytag doesnt want to address. Buy something else!!!

You can not add water to the fill, blankets dont even get wet when you wash them, you can do double rinse but cant control the fill, have to sit there and lift the lid up and down for 20 minutes to get enough water in the machine! The washing machines have turned into absolute garbage! Wish I would have come here first, whats the difference if I control the load size water or IF I SELECT DOUBLE RINSE? THIS WASHER 200% GUARANTEED I WILL NEVER BUY A MAYTAG AGAIN. ABSOLUTE TRASH FOR $700.

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

Its unfortunate that Maytag expects their products to be so short lived, they wont produce parts for their appliances after 7 years. They just told me they are only required by law to make parts for their products for 7 years so thats what they do. So unfortunately, if your microwave outlives its handle, youre going to have to replace the entire appliance which will cost me almost $500. I will never buy another Maytag or Whirlpool products because of this.

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

I just saw that there had been a class action lawsuit settled in 2005 for the Maytag Neptune front load washer and I was never notified as an owner! I have this crummy product and have been living with it for more than 10 years! I just scheduled a repairman to replace the moldy gasket (for the second time) and the noisy pump, and a latch that has to be slammed for a sum of $438. What a crock. I was told this was a top of the line model when I purchased it for $999. Ive never had such a piece of junk before in my life. I run loads of bleach weekly to control the mildew.

Please Do NOT purchase the Maytag Aqua Lift Gas Range. It does not clean anything, you will pay more money for a cleaning oven that does not clean any grease or droppings if you cook. This is not an Oven for any one, or family that cooks large meals or has gatherings. I had the technicians at my house over 4 times and they confirmed that this oven is not a self cleaning oven. It doesnt get hot enough as your self cleaning ovens. And MAYTAG did not want to hear anything, basically not clean much, but advertised as a self cleaning oven. Having been a Maytag customer for years I will never buy a Maytag product again. And we need to support American made, but not when the consumer is misled.

I bought a new washer and dryer on Sept. 9, 2011. Front Load Commercial 2000 Series. I have had Lowes to my home 2 times since it was delivered because it shimmies across the floor. I am very upset with the purchase of the Maytag front load washer. If you could please get back to me on what can be done. I would like for a representative to contact me and come and look at the situation.

I bought an off-white or light cream color gas Maytag stove about three years ago. When I first used it to boil some water for tea, the light colored grills turned black. And this is without cooking a full meal, merely boiling water. After a few more uses with light cooking, and a few spills on the cooktop, I discovered that it was simply impossible to clean. The glass on the oven door became discolored with the first use, and is also impossible to clean. I purchased several types of cleaning items and sponges, and nothing works. This is a disgusting stove. I hate it and I wish I never bought it. I will never purchase a Maytag anything ever again. Its the poorest and cheapest no-quality item - a total waste of money.

Maytag Bravo was making loud noise in the Spin cycle. Ordered new bearing, shaft and parts from Amazon. Also had to order the Bearing tool, cost more than the bearing parts. Total cost $145. Watch a youtube video on replacement, took about 3.5 hrs by myself. Biggest problem I had was lifting the washer up over the drain pan it is in. Washer is on the 2nd floor.

My experience over the past 2 years with my top loading Maytag washer is echoed in almost every review here. 1. Not enough water to clean the clothes 2. Clothes come out still dirty and covered with detergent 3. Barely agitates 4. Repeated repairs for leaking and computer board breakdown 5. Complete lack of interest by either Lowe’s and Maytag when contacted. I could write a long, detailed complaint but it has all been said quite well. We need to band together and file a class action lawsuit against Maytag. Any lawyers out there willing to take this on?

We purchased a refrigerator in December 2010 with a 12-month warranty. Since the refrigerator was delivered, we have experienced nothing but problems. Most recently, there was a problem with the auto defrost causing us to lose all our food stored. It also caused water damage to our floor. We scheduled maintenance with a contracted company through MayTag. After three scheduled visits, which made me miss 3 and a half days of work resulting in an additional loss of over $300, our refrigerator is still broken and they just want us to schedule another maintenance visit. When calling Maytag customer service we are literally told, “your loss, there is nothing we can do to resolve your issue, we can only continue to send out maintenance.” I am so disappointed in this company, the product, the customer service, maintenance service etc.

I had bought Maytag Dishwasher MDBH979AWW3 in Sep. 2009. Oct 2011, the dishwasher stopped working and the control panel had to be replaced, few days later, it stopped working again and the Thermal fuse had to be replaced. Now two months later, it stopped working again. Till this point, Ive spent a lot of money on the repairs and I wish I had used that money to buy a new dishwasher. Looks like not just the Maytag dishwashers are faulty, but even the parts they have are faulty. I will not recommend any Maytag products to anyone.

This set is a GREAT ONE! I love my HQ washer and dryer. The washer has so many settings to choose from for all different loads of clothes. It washes and spins everything great. My dryer is so nice! I can dry a load of whites: towels, washcloths, hand towels etc in record amount of time. I would highly recommend them both.

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

We purchased a Maytag Dishwasher Model #MDBTT60AWW3. Shortly after manufacturer warranty ran out, the control panel went out. Luckily we had purchased the extended warranty. The repair company came out and put a new control panel in it. Two months later, the control panel goes out again. The warranty firm sends out a different repair company. They replace the control panel again. This time it doesnt work. They replace some of the buttons as according to the repair person they arent registering the correct OHM reading. It works again. Yay!. A week later, its not working again. The repair company is coming back. This is really starting to get old. Between the multiple times it has broken down, waiting for the repair company to come out, diagnose the problem and order parts, we have been without a dishwasher for approx. 2 months the multiple times it has broken down. Im so fed up with this thing. I also will never ever buy another Maytag again. They need to have a major recall on these because of the terrible, terrible control panel. This isnt just me, its a lot of people.

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

We are on our 2nd Maytag refrigerator in 6 years and both units have failed. Maytag will not stand behind their product and the service company declined to come out to look at the unit because we were upset and contacting the BBB. So we have spent thousands on 2 refrigerator units that have lasted 2.5 to 3 years a piece. If I could give no stars I would and I would advise to look at other companies and models.

Consider all other manufacturers before purchasing a Maytag dishwasher. Our 3 year old model MDB8949SBB1 is junk. The control panel is a joke. Works when it wants to. Do not spend your hard earned money on Maytag.

MF12665XEM7 - Maytag Refrigerator purchased from Home Depot. We initially thought it to be a good value until it started leaking puddles of water onto the floor to the front sides of the bottom freezer drawer. This event repeated itself and I feared the water would seep between the floor tiles and begin to degrade the sub flooring or possibly cause mold as well. Upon further investigation of lying on my side and pulling the bottom drawer open, I felt, what I thought to be ice on the bottom of the refrigerators floor. I gently inserted a smooth butter knife and with a nudge, a whole sheet of ice about one half inch thick, lifted from the refrigerator floor. I have since had to repeat this about every three weeks or so. Im nearing retirement and shouldnt have to lay on my floor like this to protect my floor and to keep my wife and I from a potential hazard of a slip and fall from this water on the floor! Dependability People? Hardly! I think they got outsourced! Im disgusted! Thank you!

We purchased our Maytag dishwasher on 12-26-2013. It was installed in early Jan. We did not buy an additional warranty. We put our faith in the Maytag name. We had no problems with our dishwasher. It was smooth and quiet. The one year warranty ended in Jan. 2015. In March of 2015, our dishwasher control panel began to go crazy. A short while later our Maytag shut down completely. Every now and then the washer will come on by itself. We will try and cut it off. It cuts off when it is ready. We have got quotes on getting it fixed by Maytag. With installation and tax, our Maytag Dishwasher cost us $649.22. Our complaint is the same complaint of thousands of other customers - the control panel. Maytag should have a recall and fix this problem. Maytags remedy for this problem is to sell a warranty for each year that a family owns the dishwasher. That is not acceptable. Please consider a recall on this item. Our model is MDB7749SBW2. Our serial #F33406909. Thanks for your help.