I bought a Maytag Range with the Aqualift feature 3 years ago. Worse purchase every, the oven clean option (Aqualift) is useless. It do not work at all, be prepared to spend hours cleaning. I followed manufacturers instructions and its useless, after running the cleaning cycle three times I gave up and starting cleaning for hours.

We purchased a Maytag front load washer in May 2006 (MAH6700AWW). In November 2012 we had a leak and called a repair service. We were told it was the dispensing hose which had a hole worn in it and was replaced. In February 2014, we called the same service and was told that we had the same problem. Now in November 2014 we are experiencing the same problem. We have notified Whirlpool of this problem and each time were told that the machine was too old to reimburse us in any way. Guess who wont be buying any Whirlpool products if they do not back up their faulty workmanship.

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

Maytag may have pay to replace defective controls. 1-866-931-7384 is the number to call. I have owned my maytag dishwasher for about 18 months. Its control panel was never great, but now my dishwasher wont work at all. Apparently, the tiny inside the control panel rust away because they arent sealed.

This appears to be a common, known, well publicized problem - freezer drain clogs and needs to be either changed or repaired with a fix, a free replacement part for the drain seal. Easy to install, takes 15 minutes. HOWEVER Maytag will not give you the part!! In order to take advantage of Maytags correction for a well known, chronic, manufacturer defect, you must engage an authorized service person for hundreds of dollars and wasted vacation time waiting at home for them to show up. Unlike any other product, recall this one is not free. My kitchen is full of Maytag products; dishwasher (not so good), range and a refrigerator that had to be replace when the compressor went out after six years. However this is the last straw, Ive learned my lesson, seen the light, THIS IS THE LAST MAYTAG PRODUCT I WILL EVER BUY.

Hello, My recently purchased dishwasher has leaked water within less than half an hour of the fifth time to be used and showed error: F8E4, dishwasher model and SN are: Model: MDB4949SKZ. Serial # : FA3003347. Registered: 09/11/2021, Ive been calling Home Depot who in turn asked the installer to check the connection, and the latter advised and reported its a manufacturer issue. And calling Maytag for several times but no response or action. On-line service scheduling of Maytag is not working!!! And the live chat is not helping, as well. Now my dishwasher is not working since more than two weeks, knowing that it has been installed only a month ago.

Replacing a working but noisy 14 year old Sears dishwasher for the newer Maytag was my bone head move for 2011. It died the first year control panel shot, no warranty. Paid for repair. This month dead again; same problem. Recall this stainless steel garbage. Maytag model MDBH949. Maytag, never again. Bought twice and last time.

I have a bearing going out. The Bravo washer makes a terrible noise. Now, they tell me I need a new tub/bearing. This repair will cost me more than $250.00 plus service calls. This is the second repair that I have had on this machine. It is only 4 years old. I use it twice a week. I will not recommend Maytag to anyone and I will never buy another one. They should check the internet for complaints and realize that there is a problem.

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

Just replaced a washer that lasted over 7 years thru 3 renters with the Bravos top loading washer. There is nothing efficient about a cycle to take 73 mins to wash 20 articles of clothing (t-shirts, socks and underwear). The machine dont wash the top of the load. Also the deep clean feature isnt deep cleaning. I recorded a video of 20 mins of the machine not washing properly before going into rinse cycle. If this item dont produce refunds of the amount of water wasted RE-WASHING and electricity because it doesnt clean on first wash, then its time for Maytag to pay my utilities. For the money spent on the machine, going to the laundromat every other week with 1 roll of quarters each trip comes to be I can wash for 4 years and will outlast the longevity of the machine before it breaks! Also bulky mode is how you get more water in the machine but will take 63 mins to wash.

This machine was purchased two years ago at the Home Depot. I wanted a top loader that was not digital and without a lot of choices. It has been nothing but a headache with every wash. I had a Maytag serviceman come out immediately and he said nothing was wrong. Every wash load I do, has problems. The dark loads are always full of white spots and the towels are torn up. Just bought some new towels and after the first wash, they were ruined. I will never ever buy a Maytag machine. These new He machines are ridiculous! I no longer have a receipt, but the complaint should help consumers in their decision to NOT buy a Maytag machine.

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

Bought Maytag dryer in December 2016. Worked fine for first 3 months. Then blue coloring showed up on back of drum and came off on white clothing. Had tech come out. He took pics and send to Maytag. They said it was normal. Further talks with customer service brought statements that we caused problem by drying blue jeans. Funny we never had. They just continued to say this discoloration was normal and we did something to cause problem and nothing they could do. But at least they were sorry for our problem. Whirlpool does not stand behind products. Dont buy.

I bought a Maytag washer expecting To get the best and have already had Service on it three times and it still isn’t working. I have spent a fortune at the Laundromat when I have a 4 month old washing machine at home and not getting anywhere with getting anything back on this. I am very disappointed in this Washing Machine.

I thought I was nuts - only 2 of water in a full machine of bedding or clothes. I agree with all the other one star remarks - clothes still dirty, still dry, hardly any water and if you use the bedding selection, it takes nearly 2 hours to wash a load and then it doesnt spin dry so you have to rinse and spin again. Very disappointed with the machine. Yes - class action lawsuit? How do we do this.

Dont buy this machine. Although it is an HE machine and supposed to save on water, it does not give enough water to at least cover the clothes. I had repair come in and they changed the computer but no improvement. The cycles determine the water amounts not the type of clothes you are washing. So if I only a few things I use cold water wash, if I have a half load I use deep water wash and have to add water to it. Its ridiculous. Do yourself a favor and get an LG. I wish I had.

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

I dislike Sears and more so Maytag. I bought a Maytag Bravo XL MCT. It worked nice with very few hiccups until 1 1/2 years old. Then the washer went to the lock and done mode, thought it might be the lid switch down the washer up. Looks like I would need to change out the whole panel. Its not worth the trouble OR time to put one dollar to repair the piece of **.

I purchased and installed a high end MAYTAG above the stove microwave. After 3 years of light use I hear an electric cracking sound and it dies. Of course no warranty coverage. Model MMV5208WB-1. I have to conclude MAYTAG builds junk and does not stand behind what they sell.

Lets be real and say that people with good experiences dont often end up on websites writing reviews because they are busy enjoying their product! I purchased my set in early 2012 and will admit that initially there was a learning curve with using a washer with no agitator. I enjoy doing laundry and Im really good at it but with this washer I had to change my routine. Always pretreat stains. Deposit clothes loosely around the drum and shake clothes loose before putting them in the dryer. My clothes come out great! I have a child, two dogs and a greasy truck driver man and everyones clothes smell great. I can wash my king bedspread and anything else in my house with no issues. And my washer has never torn any of my clothing, however fragile. I dont iron often and I hand wash nothing.I give 4 stars instead of five for the extra steps to ensure my clothes are clean and wrinkle free. No they dont make things like they used to but thats with all the new stuff. My moms 3000 dollar Samsung set (her washer) isnt working as I write this. Too bad more people with good experiences dont get online and share. Hope this has been helpful.

These machines have lots of service problems, although Im not familiar with the newer models. The function and the features are adequate, and typical. And overall, again, I have no complaints other than shortly after purchasing, there was a circuit board recall for these machines, and fortunately, I had a repairman who knew of the issue, and guided me to a cost free fix. Overall, it has served the purpose well of cleaning my clothes in a decent fashion.

Centennial HE top loading washer - When I put the HE Tide powder in the washer, it does not always rinse well. I have to rewash often. I use very little soap.

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

Purchase a top loader washer machine in Nov 2014, it is now Jan 2015. It is not completing drain cycle, leaving wet cloth. I am Not happy with the service. I had the tech people come out 3 time and saying to call customer service, and they keep sending out people. They do not want to give me back my money. Unhappy, waste of money, will not get another Maytag appliance again.

MER8700DH - Within 6 months, left rear burner stopped working and Maytag repaired it under warranty. Within next 6 months, and just before end of warranty, right front burner stopped working and again Maytag covered it under warranty. Within the second year of ownership, the oven was not working correctly and Maytag refused to cover it because it was off warranty. So I called a local appliance repair company who gave me an estimate of over $300 to repair it and basically advised against repair stating that this stove was a piece of junk. So I replaced it with a GE and junked the old one before it was even two years old. I filed a complaint with Maytag. At first they said they would go half on the labor, but then they said I should have bought the extended warranty and refused all further help.

I have nothing but great reviews for my Maytag experience... In approx 1975 I purchased a Maytag W&D, Model MAH4000 MDE4000, when their advertisement was portraying Maytag repairmen as the loneliest repairmen. Maytag was so dependable that the repairman was NOT needed...and it was true... That Maytag W&D set lasted til approx 1998 when it was upgraded to the Maytag Neptune MAH4000 series... Had a minor problem with mold in the washer, but Sears and Maytag replaced the seal and made another modification... We also dried the seal at the end of the washing day and left the door slightly ajar between uses... Have not again had that problem.I have since given the Neptune set to my daughter and the washer and dryer are still in operation, WORKING SUPERBLY I might add... So I am searching for a good quality Model MAH4000 and MDE4000 to replace my current much older, yet functional Whirlpool... It may need some repairs and about a year ago, I spent $173 to replace the Pump which was clogged by a sock inadvertently stuffed around the top of the drum when too many items were pushed in at one time. I prefer not to throw additional money at this machine! So, if you know of a Quality pre-owned Maytag Neptune washer and dryer in the Lexington KY area, please contact me...

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

Bravos 4.3 High Efficiency Washer - The worst washer ever. I recently returned from burying my step-mother. She actually used the same washer and dryer, by Maytag, for over 50 years. Those days are gone forever. This is my second set of Maytags in ten years. The first literally stopped working just after the first year warranty ran out. I still have them inside my pantry, like a set of anchors. Notwithstanding that, I thought, Maytag was a good brand, it must have just been the style of machines, so I purchased these in January. After over six months of usage, I am amazed at how many times I have to wash a single load of clothing to get the items clean. Who cares if the machine saves water? What was wrong with having an agitator? I literally have to remove freshly laundered clothing, turn it over and run the wash again to get the top of the laundry clean. I have had a blanket finish for the fourth time to get it clean, only to have to hang it outside because it is so full of water, the weight keeps it from spinning properly. And why would you remove a timer feature which permits very busy, working people, to wash their items while they are on the way home or in the middle of the night so that there is no waiting to pop the clothes in the dryer? None of the cycles takes less than 80 minutes to complete. Who has 80 minutes to wait on the washer to do its job? I am so upset about the amount of money I spent on all of these machines. Just think, I could have brought the over 50 years old set home from my step-mothers and had a washer and dryer do what they were supposed to do -- clean the clothes.

This refrigerator has been my worst nightmare come true. Everything existent freezes: salads, tomatoes, berries, cherries, milk, water, etc. Never again will I purchase a Maytag product. Service is non-existent.

Purchased a Maytag Dryer, Washer and Oven Range in December 2011. Both washer and oven were serviced within 1 year under warranty. The dryer stopped working in August 2013, not under warranty. Total cost to repair is $450. Called Maytag to see if they could reduce the repair cost, answer... NO. Maytag spends millions of dollars in advertising... Built Strong to Last Long but they cant spend several hundreds to keep customers. Will never buy a Maytag, Whirlpool, KitchenAid or any other related company product ever. Their motto should be Built Weak to Last Weeks.

Purchased top of the line Gemini oven a few years ago. Lower oven stopped working. Maytag repair said igniter not installed properly at factory. I contact Maytag customer service to see if they would help with repair cost. Rude response from them... basically saying anything fails after 12 months not our fault. Rejected my request without even asking details about product which model etc. Unilateral rejection. Horrible customer service. I will never purchase Maytag appliance again. Horrible, horrible, horrible. Avoid this company and their products. They do not a good product and they provide terrible customer service.

I purchased a Maytag quiet series dishwasher (Model Number: MDB6759AWW) for $500.00 in May 2009. Three months later, I started experiencing difficulty with the control panel. One light would continue to blink and it would not do anything else. I called to have it repaired but by the time he was to come out, it started working again only to stop working again the next week. On 7 Oct 09, the repairman came out and replaced the panel. Then, about six months later, it stopped working again. I called again but canceled the appointment because it started working again. Then, after having it for one year, it stopped working again and I called only to be told that it was no longer under warranty. Now, we cant get the control panel to do anything. From all the other similar complaints I have read, it seems like there is a defect with the control panel. A dishwasher should last for more than one to two years. This is very frustrating.

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

We bought our Maytag dishwasher less than 2 years ago (model MDB8969SDM0) and we are remodeling our kitchen now January 2018, and when we pulled the dishwasher out we found that the wire (12/2) had melted into the back panel. We won’t be putting this Maytag back in.

Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!

We bought our $600 Maytag dishwasher less than two years ago and have had three separate problems with it, from faulty instillation, to a faulty seal to faulty control panel. The first problem was covered under warranty, the second problem we fixed ourselves and the third problem, nothing can be done except pay an additional fee of $250+ for a new part. Maytag used to be a good name but with three problems in under two years, the only guarantee given is that if you buy one, be prepared for problems. This company does not stand by their products and will only ask for more money to fix their faulty items.

Maytag BRAVOS XL Washer - The worst washer I have ever used. Do not buy! It does not use enough water and leaves a white scummy residue on dark clothes. You have to wash them all off in warm water and then send it through one or two more rinses to get it washed off. I may as well do laundry by hand! Absolutely disgusting!

I have had this refrigerator only 6 weeks. The freezer works but the refrigerator does not cool properly. I went back to Home Depot - Baltimore MD and told them I have lost 3-1 gallons of milk for it spoiled. I am right now putting a 4th gallon in and out of the freezer trying to keep it. A serviceman was to my house the other day and stated this brand new Maytag refrigerator only had in my home 6 weeks needs a new board and a flapper that opens up in freezer that sends cold air to refrigerator. Parts are on order. Home Depot would not trade a Maytag refrigerator that worked well and take this lemon back. I am stuck with a lemon I only bought 6 weeks ago.

Peeling of paint off the oven finish, inconsistent heating, fan goes on and cant shut off until the oven cools, have to leave door open in order to shut fan off. The paint peeling is really bad. It is right where the heat escapes from the oven, have to touch up paint every so often so it doesnt look so bad and the discoloration is covered besides the peeling.

Bought washer and dryer as a pair and Ive owned for 8 years with zero issues. Everything works as built and promised. Why would I expect anything less from a brand like Maytag?

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

My husband and I just purchased on 4/8/17 a BRAND NEW MAYTAG 4.3 CUBIC FEET CAPACITY FRONT LOADING WASHER WITH STEAM AFTER OUR PREVIOUS 15 year old washer that we both used just finally started having issues. So we decided to go new and with front loader with good brand. How sadly I was wrong! We brought our washer home, hooked it up and turned it on with 1/2 load of tiny laundry. It didnt even make it through one load! This POS started throwing error codes E1, E2, F8, F9, Suds and wouldnt drain any water. We reviewed the manual again, checked the filter hoses and detergent. All was fine but washer wouldnt work! I called Maytag 2 days later on Monday and after repairman came to look at it Thursday said it needs new drain pump and today now power wont turn on and nothing will work on front of machine, mind you this machine is brand new! I am so disgusted and angry that any company would sell this quality to anybody and at the prices they charge! NEVER AGAIN WILL I PURCHASE ANOTHER MAYTAG!

I have a top loader Maytag washing machine, Model MVWB835DW4, bought in 11/2019. Five months of light use, the lid cracked. Received a replacement and four months later the lid once again cracked in the exact same spot. Requested replacement parts under warranty and I was told that a service tech must install the lid. Due to health and safety concerns related to Covid, we are not take any chances letting people into our home. My wife and I are 70 years old and are at high risk. Maytags response was they would not send parts under warranty to me and a service tech must install the parts. If I dont let them in by 11/2/2020 (the end of the warranty period) then I would have to pay for the parts. Maytag has the very worse customer service in the industry.

This was purchased 3/25/2010 with the Home Depot Service Contract thru 3/2015 . We have already had a service call in 2013. We were OK until January 2015. Now we join many other customers with the leaking defroster. We have taken all the steps of the other customers. We went and called for a service appointment. Weve spoken to Maytag Customer Service 800-253-1301. Ive asked if there was recall? NO! I asked if there was log made of my call, NO! Any work done had to with Maytag Authorized Repair Person. The Home Depot Contract use a Non-Authorized Service Person. Weve gone to Home Depot. We are in a catch 22! We have spent good money on this refrigerator. Out of sight, out of mind. We will go back to Home Depot Again!

Purchased washer March 2017 and had to get it repaired twice by the end of 2018. The top loader even with agitator does not clean clothes very well. The repairman said not to fill the washer above halfway so I can only wash about 4 pair of my husbands heavy soiled work jeans. I won’t buy another Maytag.

I love the fact that there is no agitator in this machine. It give lots of room when washing bulky comforters. I also love the vast amount of settings for load size and the soil settings. The con of this washer is that it has broken down on us twice in the 2 years since we purchased it. The pump has gone out both times. Unfortunately it looks like we will be making a purchase of a new washer in the near future because another mechanical issue has arose.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

I have bought a new Home Depot Maytag Impeller HE washer. After 6 repeat washings of 2 items that are lightweight dark brown it was obvious after drying they had soap and lint and lot hairs on it. I reached with no he detergent. The last 4 times the water level filled to 1 depth even for high level water setting to extra rinse or power wash settings. I went to Home Depot and they suggested I call Maytag repair center on Tuesday after the labor day holiday to have them check it out. I will also call the supervisor at Home Depot as I do not feel paying $600 for a faulty machine is acceptable.

Wish I had read the reviews! I have had Maytag before and they were awesome. New purchase is horrible! Doesnt clean the clothes, leaves a residue on clothing and dryer does not dry properly. Called Maytag and they said use Affresh. Spent $10 on a pack of 5, and it did no good. My dark clothing is getting ruined! The washer is also incredibly LOUD! Very disappointed in this company and would never recommend them to anyone! I had purchased at Lowes, but had a delayed delivery, so I cant take them back, or I would.

Water level is totally inaccurate, if you do get enough water in it, it will not spin clothes dry. This is the worst purchase I have bought in my entire life. This washing machine fails in every aspect period!! AND the matching dryer is a waste of space as well, clothes come out damp regardless of setting or time period. When I was younger, Maytag meant something, not anymore! I have searched to see if there are replacement sensors, or upgraded components to make these machines work properly, that I would even be willing to pay for myself and get them installed to make them functional, but NO they dont even offer that... we are just stuck with them. My water bill is higher and my electric bill is higher too! From these machines. I wouldnt even sell them used to another person. I wouldnt want them to inherit these problems, but as soon as I can save up enough money {being disabled} I will get these hauled off and buy a set of Speed Queen machines. My wife and I are so repeatedly disgusted!! I wish I had the receipt so I could post it for more proof.

Our Maytag dryer is only, maybe, 3 years old. I do not dry towels, jeans or heavy sweatshirts in it (I line dry and then soften up in dryer). I clean the lint filter each time. Our heating element has gone for the second time. The first time it cost $200-250 to repair. It is so sad that our appliances are not made to last as they did. Or is it just Maytag? You can be sure we will not buy another Maytag item. I am looking into recalls at this time.

I purchased a Maytag Bravo washing machine item # 26 23872 for $617.69 on 11-23-11 and it was delivered and set up on 12-02-11. My problem is if you have dirty sweaty clothes, you cannot get them clean with such little water. I used the HE detergent as directed. I talked to a woman at the local Sears Appliance store this morning, 7-11-12, about it. She said I need to use Affresh. So I did clean my washer but with a similar brand and my clothes are still stinky. I have even washed an empty load or two with bleach and hot water. I make sure I wash with hot water and completely dry my clothes.When you take a bath and dry yourself off with a towel, it smells like a musty basement. I am allergic to mold. I cant even take a wash cloth, get it wet and wash my face without wanting to throw up from the smell. I have had guest comment on the towels as well. Its embarrassing. The problem is you cannot clean something with an inch of water in the machine. I am 58 years old and now have to do the wash. I went to the store and asked if we could return it for an exchange or anything like a discount on a new one and she would not budge. She said it had to be within 90 days but 90 days was in the middle of winter and I was not having dirty sweaty clothes from doing outdoor yard work.Now that summer is here, 7 months later, my clothes have been smelly for a few months. I cant take it anymore. I showed the woman that I had been to Lowes and had an estimate of 10% off with free delivery, set up and haul away. She said she could do 15% but when you add on the delivery fee, it was higher than Lowes. I purchased my whole upgraded kitchen stainless steel appliances for about $7,000 and this set of washer/dryer but Sears could not help me out? What a disappointment that a loyal customer such as me could not at least get free delivery on a new washer. I went right back to Lowes and ordered the same machine I wanted Sears to sell me matching Lowes price.So now, I am stuck with a 7- to 8-month-old machine still in the one year warranty that is like new but is a worthless piece of junk as my clothes all stink. Run, dont walk if someone tries to sell you a low water HE machine. I tried sending this letter to searsinfo.com corporate office and it is rejected even though the website gives you that address.

I bought a new washer and dryer from Clarks Appliance on North Monroe St.,Tallahassee, FL. I do not like the washer. It is a top loader and has a lock on the lid. The pause button is supposed to let you open and then is supposed to continue the wash. But it releases all the water and shuts down. I asked to return the washer because I have had it only three weeks. They wont take it back. So now I would like to trade or sell it.

A lot of the reviews contain complaints about the Bravos XL MCT top load washer. We purchased one in December, 2015, and so far have not had any problems. We had a 3 yr old Whirlpool side loading washer that we just gave away, as it never got enough water to even dampen a comforter or quilt. This machine works very well, in spite of lower level of water. I was pleasantly surprised when I could see the water level with the first load! The controls are not as intuitive as other machines; e.g. spin only requires you to select Rinse/Spin cycle, and THEN turn OFF extra rinse. Perhaps the proper way is to have a Spin-Only cycle, and then tell the user to click the extra rinse ON. We do probably 1 load a day. Water bill has not been significantly higher than when we had the Whirlpool that hardly used any water. Today, though, a heavy quilt (it WAS distributed evenly around the impeller) was put on Bedding so the water level would be a bit higher to ensure the entire quilt was wet. Fine so far. However, during the Spin Cycle, the unbalance became so violent that the washer stopped for a few seconds and then went BACK to the Rinse cycle. It did this several times before we realized that the time remaining had not gone down in over 30 minutes. My guess was that the sensor believed that maybe some additional water with another Rinse cycle MIGHT even out the load. It didnt. I finally stopped the machine, redistributed the quilt and then ran the Rinse/Spin cycle, choosing NOT to do the extra rinse. All came out fine. There was NOTHING in the manual indicating that this might be needed, except for the instructions to Spin only. If I have any other problems, I will send here.

I purchased a Top Loading Maytag January 2019 (High Efficiency Washer) and I have had problems with it every time I do laundry. It doesnt matter what cycle I have it on. It doesnt fill properly when I put it on deep full. It tangles my clothes so I have to untwist them when I take them out. It has torn some of my things due to twisting. Some areas of the clothes dont even get wet. Some areas also do not get rinsed properly and I have to repeat the cycle. I have had repair people come out and they cant find anything wrong. I am so unhappy with the washing machine and Maytag just ignores the issues I am having. Im going to have to give it away and get some other brand. I am just devastated that I spent all of this money and clothes are getting ruined.

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

We purchased a Maytag dishwasher model number mdb7749sbm in April 2013. March of 2015 the controls stopped working completely. We looked online and instantly found it was a problem among many others, and said it was a result of corroded ribbon cable. We opened the panel and, sure enough, inside the ribbon cable the electrical wires were completely rusted through! We called Maytag, and, of course, despite the numerous complaints of the same problem, they would only fix it if we paid $250, or send us a replacement part for $350 to fix ourselves. Not going to spend that much on a dishwasher that already cost $600 and only lasted 22 months! We are attaching a picture that shows after we tried cleaning the rust (when Maytag refused to fix it) how much of the electrical wires disintegrated! We tried soldering a small wire to connect it again, but the ribbon was so thin it just melted right through.

Ive read a few reviews and would have to agree. This is the worse washer I have ever purchased. I agree clothes go in dirty and come out dirty. I have to hand wash clothes to get them clean and wont even mention how long it takes a white t shirt to start looking like it was placed in mud vs being placed in a washer. Called Maytag and they said I was loading it wrong even though I was loading it as suggested by the manual. Then they suggested it needed service. I think not after reading these reviews.The irony is that I had called for service on a front loader due to prolonged washing cycles, the repairman was as useful as this MayTag washer. Come to find out I replaced a perfectly functioning washer, intake screen on cold water needed to be cleaned, for this piece of useless metal. I guess since reading that Maytag doesnt value its customers by offering some type of consideration I will replace this piece of crap. Please dont buy the Bravo series. You will be sorry and you will never have whites white again.

Dishwasher control board has completely started blinking cancel when not touching it, ran for the entire time I was in Church. Numerous problems, only 2 years old. NEVER would I recommend this brand, EVER!!!

Great appearance, great job on getting our clothes clean and dry. Good dryer cycle choices and output. Good washer cycle choices and output 98% of the time, BUT, sometimes the washer needs a do over about once in 50 loads. Overall, two thumbs UP.

The washer machine is only 2 years old and its broke, at first it wouldnt spin and now it wont wash. Everyone is saying between the parts and service fee, it will cost 200 to 300 dollars or more to fix, most technicians wont repair them because they say that we may as well cut our loss and just buy a new one. No one likes these machines. I wish I would have known what a sham the washer machines were before purchasing.

Im very pleased with both the washer and the dryer. The front-load washer is very efficient with many washing options dependent on items being washed. Spin cycle spins very well which lessens the dry time of the washer.

Purchased this washer from Saginaw, Michigan location in 2007. Started sounding like it was going to come through the wall of the laundry room so I contacted repair service. Told bearing was bad and that cost of repair would be $1,000.00 - literally laughed at repairman. I find it difficult to believe that a washer is built to last 7 years after paying so much for it.... My years of purchasing solely from Maytag have thus ended.

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.

My Neptune dryer purchased in November 2005 had the drum crack at about three years old. I complained so much that they finally agreed to send a replacement drum for free. Now, two years later, the drum has cracked again and tore through the housing on the front of the dryer. The repairman said it would be too expensive to repair. Consumers, beware.

Our refrigerator is 2 years old and still under warranty. The ice maker had to be replaced. Now the water leaks on the floor. The deli drawer cover broke and when you get ice out of the ice dispenser it flies all over and goes on the floor. Our dealer has been fairly helpful.

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

We purchased a Maytag dryer in Dec 2012 and several days ago the heating unit failed (mid April 2014). I did a quick search on this site and a few others where I saw numerous such issues with Maytag dryers. I realized that I was 4 months beyond the warranty period but took a shot at calling their customer service line to voice my displeasure only to get the company line that they could do nothing. My wife and I have been married 27 years this year and this was the 4th dryer we have purchased (1st and last Maytag) which obviously did not last like the other brands or like we expected. I definitely do not recommend this brand!

In the last 6 years, Ive had a Whirlpool dishwasher that the motor seized due to poor design and overseas Asian motor builder (3 years of normal service). I cleaned the motor and it seems to barely work another couple of months but the design and manufacture process was garbage at best. Thinking I would go with the best produce MAYTAG (Old commercial about repairman having no calls), only to find out that it too was bought out by CRAPPY WHIRLPOOL and it too lasted a couple of years with cheap MADE IN CHINA electronics!!! Thats why we are the laughing stock in the world as far as products.I remember the days of where built in the USA was the best of the best, now with selling our great nation down the toilet so some Wall Street Commie can make his/her biz-zillion dollars and sell this nation down the toilet. Maybe they need to go down to Arlington and see who really has paid the price for their luxurious life-style!!!

Washing Machine MVWC6ESWW - The fourth time was October 12; I called. Shreka at Maytag said she would send someone out at no cost on October 15, between 12-5 pm. Justin called from AE at 5:05 pm stating he was on his way. He then asked for my receipts. We were moving and had packed many things. He said he would call and find out. He said they were out 7/2011, 9/2011 and again 9/2011 all for the same problem. I requested in September 2011 that this was a lemon and send me another. I was assured if the same problem occurs, it would be covered. Well Justin said it isnt covered anymore and it was due to being made overseas. The cost to fix it is around $350 to $400. The washer cost me $383.40, plus I bought the matching dryer of $403.39. This makes zero since. Please advise.

I am absolutely disgusted with this Maytag Bravos XL washer. Have owned it 6 months and cant wait to get rid of it. We live on a farm and have cattle. If jeans go in the machine with mud on them, they will come out with mud on them. I have tried soak, deep water wash, power wash. Nothing works. I might as well put a wash tub in my back yard and wash by hand. Anything black must be washed by itself as it will come out covered in lint. How did this machine ever go on the market? Expensive mistake. Please do not buy this machine.

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

Updated on 08/13/2021: Today a repairman who is authorized by Maytag came out. He found the problem, some arm that popped out that is located underneath the washer. He put it back together and said he needs to order the part and it will take 30 more days. Set the washer so that it SHOULD work for a couple of loads. I spent $700 on a washing machine and I have to go to a laundry mat to get my clothes washed. Here is the clincher. The guy left no paperwork, nothing, not even a business card. So I am at the mercy of this repairman (I think he said his name was Jessie). The guy was friendly, quick and knowledgeable, however he told my husband he knew what the problem was going to be, if you knew why didnt you bring the part with you and he said the part is out of stock. Why, is this part unique to Maytag washers? So I am still waiting for my washer to be fixed.Original Review: In December 2020 I purchased a Maytag washer it was delivered in January 2021 and it worked great for the first several months. Then the machine started making noises, clicking noises like it couldnt move through the gears. Then I started noticing that my clothes were not getting cleaned. It was taking an hour to wash the clothes. I told my husband it is not agitating just clicking. We had to stop and start back up the washer just to get the water level high enough for the so called deep water wash. I was finding residue left on my clothes and had to wash them 2 or 3 times to get the clothes clean enough to wear. Sometimes it wont spin enough to empty the water in the tub. It smells almost like wire burning. It has barely been 6 months and I have to have a repairman out. I will review the washer again after it has been fixed or replaced. But as of right now I will never buy another Maytag again.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

In October 2016 I purchased a New Maytag washer (Model# MVWC565FWO) from LOWES. I bought an extended 5 year warranty with it as well. I have my invalid, totally incapacitated Sister living with me. The situation requires several loads of washing each day due to her conditions. TWO WEEKS after starting to use it we began having issues with the washer. It would stop in the cycle, lights flashing, only way to restart is to unplug it, move control from wash cycles setting to drain and spin... then within the next 3-4 loads it would do it again. Sometimes it sat for awhile I would smell like an electronics Odor getting hot... I called Lowes. They replaced it. Approximately 3 weeks later the NEW washer began doing the SAME THING...Lowes would not replace it with a different Model or brand... only send a repairman out. Long story short, he has been here 4 times, replaced the Computer Control with NO IMPROVEMENT!!! NOW Lowes is sending him out again and saying that if this doesnt fix the problem they will refund my money... My problem with it all is this... IF MAYTAG is having these type issues, WHY PRAY TELL, has a recall or solution been found and passed on to the repair folks??? I bought this Maytag due to #1 Reputation, #2 It was Assembled in the USA, NOT South Korea like the Samsung with recalls... Now all this is going on. I WANT A WASHING MACHINE THAT WORKS RIGHT!!! This is totally unacceptable and totally uncalled for. WHY could these Govt agencies and Manufacturers not LEAVE the washers alone? Computer technology... PLTTT. The old timers controls gave no problem in over 40 years of using them. Now this crap.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

Bought the dishwasher (model MDB8969SDM0) at Lowes Burlington Canada beginning of September. After two months of use, the plastic pins and attachment to the drum, top rack broke and cracked in several places. Called Whirlpool Canada for repairs many times and got the run around, spent hours on the phone and still not resolved as of December 12, 2014. This model has a problem with the plastic and breaks continuously as seen by many reviews on the internet. The technician said that this is a problem with this newest model. I have now been waiting for over two weeks for the parts with no end in sight since they claim that the parts are back ordered. Called again today and was told that it would be another week to see if they can find the pieces. This is ridiculous, I paid over $ l,000 dollars for this model and it looks like now that I will not have it repaired by Christmas. Lowes refuses to help me because they have washed their hands since it broke after one month. I have been lied to many times by customer service at Whirlpool Canada. They claim that I am the first one to complain about this model yet the reviews on the internet are full with this issue. They say what you want to hear and do not seem to care at all. It is a disgrace, I feel totally cheated and robbed of my hard earned money. Maytag is no longer a good company for their appliances and service. I am starting to think that I am stuck with this machine and that they have literally robbed me of $ l,000. Shame on you Whirlpool and Maytag.

On March 2011, I purchased a Maytag dishwasher model #MDB7749AWB1. The dishwasher worked excellent for 16 months. One morning, with dishes loaded and ready to go, the start button would not light up. The other buttons did light up but that did me no good, I need the start button. A few days later, none of the buttons would light up. I found a repair person who said it would cost over $200.00 to make repairs. I refuse to put another penny with no guarantee that this new part would work. I will never ever buy another Maytag appliance. The last inexpensive, unknown manufacturers dishwasher lasted me 13 years. Do not waste your money on this thing.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

We purchased a Maytag refrigerator (freezer on the bottom) in August 2012. In 2014 we had to have the freezer repaired (defrost drain) which cost $153. This month, July 2015, we had to have the refrigerator repaired for another $293. The problem with the refrigerator the repairman told us is the control board (p/n W10503278). He stated that they didnt make the first board very well and hes been replacing this part quite frequently for customers. I only spent $799 on the refrigerator and I already have $446 into it. That is half of what I paid for it! I wouldnt recommend Maytag to anybody!

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.

I bought a new washer and dryer on Sept. 9, 2011. Front Load Commercial 2000 Series. I have had Lowes to my home 2 times since it was delivered because it shimmies across the floor. I am very upset with the purchase of the Maytag front load washer. If you could please get back to me on what can be done. I would like for a representative to contact me and come and look at the situation.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

Within 2 months of 1 year warranty running out, the control panel went wacky - does all kinds of weird things except work right. Called to see if there is any suggestions or work arounds and was told they would be glad to set up a service call for between $70 and $100, where they could tell me how much it would cost to fix. As with the other 100s of folks with the same problem, they basically said gee, you should have bought an extended warranty. If you have this many people with the same problem then it is Maytags problem, not the poor sucker consumer who got stuck with it. If you are considering this dishwasher, run, dont walk, as far from a Maytag or Westinghouse product as you can get. If anyone starts a class action suit against this product, please count us in!

Warranty dept. will not help you! I have been told by technicians sent to service my refrigerator after it spoiled food multiple times from not staying cold. The technician flat out told me that this refrigerator cannot be fixed but they are not allowed to say that it cannot be fixed. They will not return your calls and are just flat out rude. After asking to escalate a call, the rep said the manager will call me right back in a few minutes. Hours went by and I called again five minutes before they closed to speak to someone in management at that moment. This manager told me with no hesitation that they dont always believe what their technicians say because they send out techs that are good, okay, and not good. My first question is why is Maytag confident in the people they are sending to my house time and time again that stay for three hours?! She began to get rude and disrespectful and said, Well, if you had cancer, you wouldnt believe the first thing they say... I am in awe of these remarks. How do you compare a refrigerator to cancer?! I asked for a business address and stated that I would like the address to file with the Better Business Bureau and she told me that they have all the info I need. She refused to let me speak to anyone else. This situation is uncalled for when I have the technician telling me, This refrigerator is not repairable but they wont allow me to say that and Maytag will not make this an easy process for you. Unbelievable!

Maytag fridges, obsolete in less than 3 years. TWICE! My last Maytag fridge dies at about 2.5 years. I called up customer service. It was a compressor not repairable. This was an expensive fridge. Reluctantly we bought another one as the space could only accommodate a Maytag. Again less than 3 years old, the ice maker is shot and the plastic inserts are all falling apart. This time Ill renovate my kitchen for that extra 2 inches to accommodate a different brand.

I had six service calls, one was a few months after purchase when under warranty for loud noise. I bought it in 08 and since then during the last 6 months, its freezing in the refrigerator. Service person is upset. I contacted corporate and they do not care and told me I should have bought their warranty. Yes, they had to be here when it was under warranty. Still freezing, they played with air hoses, replaced the temp panel and did everything they can, with no results. Theyre giving it one more try and it is going to be hooked up to the Silverado and put on I-75 with a sign on it. Do not buy from this company. Terrible service. I emailed CEO and no response. I just tossed a tomato and strawberry on the tile floor. Yes, buy American. They moved their plant from Indiana (union) to I think TN for non-union. Well, get what you pay for and the employees get what they are paid for. I work in the building business and everyone knows not to buy this product! Just throwing your money away. One good thing is if you like frozen beverages, this is the product to buy! Never again! Receipts in hand! Romney probably owns the stock! LOL

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

This machine may save water but I spend more time and money getting out the severe wrinkles it creates. I use my dryer and iron much more than with my previous washer. I never thought a new washer would make wash day more difficult.

I purchased the top model Maytag dishwasher, and within four uses, I noticed major water damage to the side of my cabinetry. I pulled out the dishwasher and realized it was coming from the side unit where water enters the tub. These things happen, and I phoned their customer service department expecting this unit to simply be replaced, being that it was less than a week old, and that I would have been left a satisfied customer. They were willing to send a technician over to try to fix the problem, but not replace it. I now have to replace my cabinets, and maybe even my granite as it may be damaged in the removal process. I am not asking them to fix that even though the damage was caused by their dishwasher, but a new dishwasher, I did expect them to cover. Their customer service stinks, and I suggest to anyone that if you have any problems with a new unit, the best thing to do is return it to where you bought it. Im sure they will gladly give you a new unit and send the bad one back to Maytag. Dealing with Maytags customer service is the worst thing you can do. They do everything in their power to not replace it. Instead, theyd rather lose a customer for life. Whats sad for them is that Im a builder, and I usually build approximately three houses per year. Thats a lot of units theyve lost sales on over a simple replacement of a dishwasher. Its not a good way to do business. The bottom line is, stay away from Maytag.

We purchased a Maytag Centennial line washer (Model # MVWC400XW0) and paid a little more hoping that it will last longer than a normal washer. After just 14 months, the washer breaks and we are forced to buy an extended warranty from Maytag for $300. The warranty price seemed a little high; however, the only other option was to buy a new washer. The repair guys showed and said it should be fixed.After just three weeks, the washer broke again with the exact same symptom. Since I had the extended warranty, I called in another ticket. A different repair guy showed up and he said the first guy messed up. He said the guy misread the diagnostic code and didnt even put in the part that he said he replaced. The repair guy checked with Maytag and they told him it was no longer cost effective to fix our washer. Really? They overcharged for the warranty and wont even repair it when it breaks. The only reason I can think Maytag would do this is that they know the washers are junk.

We were replacing a 4 year old Whirlpool Duet washer (bought on recommendation from sister-in-law) that needed the third repair and was putting holes in our clothes. We had purchased the warranty (which we had never done before) so Lowes gave us the choice of machines and we decided to go with the Maytag Bravos. Lo and behold, were still getting holes in clothes. Several repairman told us the issue is common and is caused by the force of the water flowing into the machines plus the rapid spin cycle which pushes the clothes through the punched holes in the tub and the clothes catch on the metal on opposite side of the tub. Turns out sister-in-law had the same problem with her Duet and (not knowing I bought the Bravos and had the same issues) bought the Bravos and also is still getting holes. So I know its not just me.We also have problem with the machine not putting in enough water so clothes do not come out clean. In fact, a lot of stuff comes out with areas that havent even gotten wet during the wash cycle. I just want an old fashioned machine with an agitator that fills the machine fully, washes my clothes and doesnt put holes in them.

I purchased this range from a Maytag outlet in Nov. 2006. No problems with it until Nov 2015. The oven igniter failed. This was serviced locally and replaced in an efficient manner by the local service tech. All is good until 2 days later when I decided it is time for an oven cleaning cycle. I set the cycle for Medium Soil (3hrs). After the conclusion of the clean cycle, the oven (bake) would not work. Called Maytag service, the service tech replaced burned up oven wiring as well as the igniter again. However, the cleaning cycle had taken out the gas safety valve control as well. I am now told there is no replacement oven gas safety valve unit available anywhere. I even called Maytags 1-800 number and searched online only to find the part on backorder and not available.I find this particularly frustrating in light that I spent over $1200 on a Maytag product I thought would bring way more than 9 years of service before it is deemed unrepairable. The average gas range lifetime is 18 years. In my opinion, not a good return for the investment. Its a shame because the rest of the range works and looks fine, which is now destined for the dump. I am replacing the Maytag with a $550. Frigidaire with manual cleaning. Will never buy another Maytag appliance or a self cleaning oven again. If the self cleaning feature has the potential to fry the controls, why would they offer such a feature, or why couldnt they warn one of the potential failure.

Top loader Maytag Bravos type 588-03 - This washer is extremely slow and does a very poor job of cleaning. I use the recommended detergent (I use Tide HE) and follow the directions being careful not to overload. I can tolerate the slow operation I guess, but the poor cleaning is a real problem. When I put a plastic shower curtain in it, no clean happens. I just throw them out and but new every time. I will definitely go back to a Kenmore with an agitator.

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

We bought this washer in February of 2010. We had the pump replaced under warranty in January of 2011, and the pump appeared to have a hole in it from some type of hard object that had gotten inside the pump and damaged it. We then replaced the L-shaped hose between the tank and the pump because it had a small hole in it - very thin rubber. Last week, the washer was leaking again and the service technician said that the pump housing was cracked due to a penny rattling around inside the pump.This washer performs very well when it is working but it seems to be too fragile to handle on normal usage. The Whirlpool washer we replaced with this one ran for 23 years with no problems before it finally went out. From all appearances, it seems that every failure we have had with this washer has been due to damage from foreign objects getting trapped in the pump. Is there no screening mechanism to prevent hard objects from entering the pump? This seems to be a design flaw more than anything.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

The refrigerator had to have repairs in first year. Maytag was aware of freezer issues and reluctantly finally replaced the parts. I had to argue with repairman because he tried to tell me that the freezer was too full.