Washer is Broken After 1-1/2 Years: Yes, the code F51 has come on quite often. Now, my washer does not work at all! Does not spin out, makes thumping noises even though I have taken good care of this machine. It cost me quite a lot of money and thought that this was a wise decision. It’s broken after a year, unbelievable! Also, clothes don’t get clean. I had to wash 2 - 3 times. The clothes wrap around each other and the machine does not clean them well. It’s a horrible machine. I have not called Maytag (Whirlpool) yet as I see from the comments that they will not stand behind their machine. I dont know what to do!

Like many others Ive read about online, our Maytag fridge model MFI2269VEW5 with bottom mount freezer has ice forming at the bottom of the freezer compartment. The ice then melts and runs onto the kitchen floor. At this point, I am able to prevent this leakage problem by removing the 1/2-inch layer of ice that builds up about once a week. Using a stiff plastic spatula, I am sometimes able to remove the ice in one large sheet but usually it breaks up and has to be removed in pieces. I have seen several videos online showing how this problem can be fixed but as a pensioner with limited income, I am sure the expense of a repairman would be prohibitive. I could likely make the suggested repairs myself but because of a knee replacement, I am not able to kneel for any length of time so that is out of the question. Besides, when we purchased this fridge 3 years ago, we expected it to run trouble free for the rest of our days. This is obviously a design problem and Maytag should be covering the cost for all repairs. However, it is a sad reality that Maytag and their owner, the Whirlpool Corporation is only interested in making a profit to satisfy their stock holders. They apparently only pay lip service to making quality products that last and customer satisfaction seems to be a thing of the past.

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

This Maytag dishwasher is beautiful inside and outside. I love that the controls are hidden. It cleans dishes very well. It has a large capacity for dishes, a rack for glasses/mugs, a small rack for cooking utensils, and a container for silverware. It is so quiet you hardly know it is working. I would highly recommend it.

This dryer ripped a gaping hole with sharp shards of metal exposed. It was working fine, and then it made a weird noise. It stopped and I assumed my laundry was done. We go to remove clothing and cut hand open on exposed metal. As if that wasnt bad enough, several hundreds of dollars in clothing had cuts in them. This dryer worked great for years, and out of the blue this happened. Im a widowed disabled mother, and cant afford a new dryer.

I had this microwave less than a year. The control panel went out and Maytag fixed it. Now a year and a half later, the same thing happened. This product was almost $400 at the time we purchased it. I have had better luck with $40 microwaves.

I called Sears to have a simple repair done to my Neptune washer and received a quote for $800.00++. They gave us a coupon to get a new washer at Sears and we did. Last week my dryer broke and I looked the repair up on Youtube. It looked real simple. A quote for $270 was given to us. Again a coupon if we wanted to buy new. It seems to me Sears jacks the price up on its parts and labor in order to push the customer to buy new. So far its worked for them and Im sure everyone else as well. Its not going to work out for Sears this time. Im no longer doing business with them and I will do the repair myself. I still got stuck with the service call but that will end as well going forward because I know now what the game is. Shame on you Sears. Double thumbs down for my Maytag Neptune washer and dryers.

My washer is less than 3 years old when I noticed the bleach dispenser has filled with water. I soaked the water out with a towel only to have it fill again the next time I washed. This in addition to the feeling I have that too much soap is left in clothes and spot removal is pretty consistently negligible.

Maytag washer was bought May 2010 with an extended warranty, which expired May 2014. This machine was used by two people with average wash loads. Five months later the machine computer programming didnt work and the machine sounded like a jet taking off. Whirlpool said a one-year warranty would cost $329! This would have been less expensive than a new machine, but I felt I couldnt trust having it repaired. A repairman very familiar with Maytag products said he had three service calls the same day with similar complaints for the Bravos 300 series. He told me the bearings were bad and the cost to fix was not worth the money and this machine should have been recalled. I bought another brand and will not buy Maytag again. When my new machine was delivered, there was grease on the floor from the Maytag.

I cannot use my Maytag gas range and oven appliance until I can purchase part #W10213446, which your factory website shows as back-ordered until 2020. This means that I cant cook a meal or have the family and friends Ive invited come to my home for Christmas dinner. I need your help to provide better customer service than Ive received to date through working with the Maytag customer service call center, and the service Maytag parts distributors Reliable Parts and WC May company have received from working through your factory website.Ive owned Whirlpool appliances since I built my home in 1989. When I remodeled my kitchen in August 2010 I chose a Maytag range, fridge, dishwasher and microwave as Id had a good experience with your products for 21 years. Youve built a great reputation for quality products and service, and I hope that you will continue to deliver on the commitment promised in your brand by resolving my problem quickly. A burner control on my three-year-old gas range and oven (model #MGR6775; serial #D00934496) recently stopped working (a Maytag design defect - several screws were too weak to hold the cooktop at the correct level) and your customer service call center referred me to A&E Factory Service for the repair. A&E service staff have been to my home twice and are unable to fix my stove leaving me without a stove for the past two weeks and foreseeable future - as the necessary part, #W10213446, is shown as back-ordered with no estimated time of arrival. The WC May company let me know that your website shows an ETA of 2020 for this part on your factory parts website.When the service repairman informed me that the part was indefinitely back-ordered today, I called the Maytag customer service center asking them to locate and expedite delivery of the part. The line staff and her supervisor let me know that they would not provide that service, as I do not have a pre-existing extended warranty contract for the range. I am willing to pay for expediting the part, but they wont give me that option. So I called the parts retailers covering the western U.S. myself to learn that Whirlpools supply chain is so flawed that it cannot provide a part for a three-year-old range.Whirlpools core principles espoused on your website say that founders Lou, Emory and Fred Upton continually improved their washer; they cared about their community, their employees and their customers. They believed that there is no right way to do a wrong thing. It also states that what truly distinguishes Whirlpool Corporation is our commitment to building strong brands and a loyal consumer base. Were focused on maximizing the benefits of our worldwide network of resources, which is unmatched in the industry.I believe that leaving me for up to two months without a range, so that I cant cook meals for myself every day, and for my family during the Christmas holidays is not living up to your brand promise. Please let me know as soon as possible how you will solve this problem.

My Maytag dishwasher control panel stopped working. The control panel failed, it was replaced. The replaced control panel failed. The control panel failed again and needs a fourth (4th) control panel. I have had to pay for service calls and control panels. I only use it 1 to 2 times per week. This is obviouly a lemon. I would like it fixed and to be reimbursed for the lemon part and service calls.

I purchased this relatively expensive range and could not have imagined how dissatisfied I would be. The Aqualift cleaning technology does not work. There is no way to clean the oven door. They stress not to use oven cleaner, but as the Aqualift system does nothing to clean the oven door, there is no choice but to use oven cleaner, which they say will ruin the oven coating. Also, the grates are very heavy and it is impractical to clean the range top. I wish I had researched further; this product is a MAJOR disappointment.

Purchased washer March 2017 and had to get it repaired twice by the end of 2018. The top loader even with agitator does not clean clothes very well. The repairman said not to fill the washer above halfway so I can only wash about 4 pair of my husbands heavy soiled work jeans. I won’t buy another Maytag.

The frontload washer 4000 series began making a very loud noise on spin. I called Maytag and requested service. The technician came and made a diagnostic evaluation, stating this has been a bearing defect affecting several of these models. I called Maytag, and the representative agreed to ship the parts at no charge. A week later, we received the parts, only for the technician to find one of the parts damaged in shipping perhaps. So another part was sent directly to the Maytag dealer. Upon my research, this appears to be a known issue with the Maytag/Whirlpool corporation, and I found where customers had requested Maytag to also be responsible for the service/labor costs, which were also covered by Maytag. I made the call today and was advised no and to be happy that Maytag paid for the parts due to a known defect and that no service or labor charges would be covered. I understand my machine is out of warranty, but this is a known defect; its nothing caused by my self.

I wish I had found this website before I bought my new Maytag washer and dryer from Home Depot on March 7, 2018. I replaced a 30 year old Maytag washer that I should have kept. I wash two loads a week so has not been used that much and now it will not drain. I tried everything, canceled the cycle out, checked the circuit breaker, unplugged it, removed the clothing, bucketed out the excess water, tried the drain and spin cycle, etc. Just will not drain or spin. Repairman is coming next week... Still under first year warranty but if it is not the “fault” of Maytag I was told there will be a $90+ minimum service charge.

My husband purchased the Maytag Bravo December 2013. We immediately started noticing clothes been destroyed and stains still in clothes. We immediately contacted Whirlpool and shared our concerns and they sent out technician. He stated that the motherboard was gone. After repairing the motherboard, that do not stop our clothes from being destroyed and making them clean. I have wrote numerous letter to the CEO of whirlpool and sent pictures. When they decide to call you back months have passed and still they do not want to help you. Whirlpool have refused to take responsibility for a bad product they invented. They do not stand by their mission. Someone please help the consumer, because this big corporation refuse.

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

Purchased washer in 2015, worked pretty good for 4 years. In 2019 belt, support rods, and control board replaced. In 2020 clutch, pulleys, and suspension replaced, waiting for service technician to replace transmission later this week. I purchased extended warranty thru Lowes, glad I did as the machine literally jumps in the air during spin cycle. Lowes stated I needed 4 repair visits to place a claim for replacement! Machine will not spin properly on high speed. Luckily I have a spare machine in the garage to use while I waited for repairs to be made. However, nothing seems to be correcting the problem. Very disappointed in the Maytag washer.

Purchased a Maytag Bravo Quiet Washing machine. Nice and big for our family and uses less water. Generally okay with it (occasionally need to rinse clothes again as they have streaks/spots after the hand-wash cycle due to low water feature). This year it started making a loud noise while spinning, obviously the bearing. Googled reviews on this washer, reviewers explained Maytag now owned by Whirlpool and not the quality it used to be. Called the repair line, Whirlpool refused to say whether or not this would be covered by the limited warranty, even though it is very clear which part is causing the problem. The only way they would tell is if someone came out, then we were charged $149 for 5 minutes of looking at the machine to be told it isnt covered. In the end we will order the part and fix it ourselves. We will remember not to buy Maytag again.

My parents always bought Maytag and so did I. Ive experienced minimal problems in the past and have done my own repairs. My new MDB4949 dishwasher is GARBAGE! Imagine coming home and seeing water flowing out of the house under your back door! The water was coming from the kitchen across the kitchen floor and cascading down the stairs like a waterfall. I pressed the cancel button, nothing? Opened the door, NOTHING! Shut off the circuit breaker, NOTHING!Water continued to flow until I closed the supply valve! The dishwasher damaged my home! Six service visits later and still not fixed! 9 days out of warranty and still having the same problem! Customer service told me to hire a plumber to fix my plumbing problem with the dishwasher water supply! Thats funny because 3 other dishwashers (in the same exact place) had no problem with the water supply in the past 23 years? Two of them were Maytag!I never give less than a positive review but, this is outright FRAUD! The dishwasher has damaged my home on 2 occasions! Unless I want to stay home the whole time its running I cant use it? The customer service is pathetic at best. The control board issue is a scam by every company. Its all designed to keep you on a service plan and is a scam! Long gone are the days of the reliable rotary timer/control that lasted forever! You can thank everyone you know for not paying attention and letting this happen! I guess we can wash our own dishes by hand or comply with this obvious scam?

Bought the Bravos machines in 2008. Nothing but trouble. First they both had to have their timers replaced because they took two hours to wash/dry a load. Then the washer began to leak. I need to keep a towel under it and swap it out with another one as it gets wet. Had warranty folks come out to repair it. Took three tries and two guys working together to figure out what was wrong. Within a year it was leaking again - back to the towels! The dryer always takes at least two cycles to get anything dry. No more Maytag for me!

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

This top load machine replaced a top of the line Maytag Neptune. It has five water levels. It has three temperature settings and four wash selections. It also has a selection for an extra rinse that I use for white loads. The washer is very reliable. Clothes come out clean with an average amount of detergent. Although this washer is more than fourteen years old, it has never needed service or repairs. By running a cleaning cycle every six months, it drains like brand new. The stainless steel drum is still as polished as it was when it was new. Even the hoses have lasted with a need for replacement.

Maytag HE Top Loader Washing Machine: I have regretted buying this piece of garbage since my first wash. This washing machine is complete waste of money and a piece of garbage. The Auto Sensing doesnt work and doesnt cover the clothes with enough water. When the deep water wash is chosen the clothes just float around but the agitator doesnt get them clean. Dont waste your money hoping it will work, because it wont. Maytag used to signify quality that is no longer the case. I am going to also give a bad review to the place I purchased this piece of garbage because all stores need to discontinue selling this junk.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

I bought this Maytag MCT washer and dryer set brand new from Lowes October 31st, 2016. When I washed the first load it made so much noise I thought it was broken. Called Lowes and they said it is just noisier than the older ones. This is the water/load sensing model, supposed to be great. I am usually here by myself, so at most I wash one load of clothes a week. I have a queen size mattress pad in there washing right now. This pad fills up the drum pretty much, I have it on deep water but that only gives me maybe 1/4 of the drum that has water in it. The pad is wet from wicking, NOT from the water covering it. How is this supposed to clean anything when the water is not covering the items?When it spins out, it gets off balance easily. The manual says to not worry about balancing load as you put it in there, but doesnt make any sense to just cram on one side as the water isnt going to float the cloth around to balance. The settings for Bulky does nothing more than the setting for Deep Water, you still do not get enough water to wash your clothes.It also does not do any good to add fabric softener to the machine, as it seems to just take it all out, you cannot smell any fabric softener on your laundry when you are transferring it to the dryer. And the laundry when dry isnt soft like it was with the old machines. I will be 62 in December 2017. My parents always had Maytags, never a problem. This is the 4th set of Maytags I have had. And bought a set for my daughter in 2013 also. And this by far is the worst. Their quality is completely gone now. Nothing but cheap made products that are predestined to fail. Friend across the street said she had looked at this set when she was in market to get a new set. She has an friend who works on appliances and who works for stores selling these models and he told her, they were not worth buying. Wish I had known that. Do not waste your money.

13 months after purchasing MDB7749SBM3 dishwasher this lights started making no sense. For me the buttons still work, but it seems like only a matter of time until they stop working too. Like many others, I opened up the door and found the corroded ribbon connector (see photo). It wasnt damp so since the corrosion happened at the point where a ridge of plastic presses the ribbon against the hot handle, I suspect heat. Obviously a design flaw. Come on Maytag. Recall?

I bought Bravos xl. I hate it! Everything about it. It does not get my clothes clean and it ties load in knots therefore being off balance constantly.

Two years ago I bought a matched set of Maytag Neptune washer and dryer. Although I bought really liked the front loading and large capacity, I bought them because they were Maytags. I remember my parents grumbling that they couldnt afford a decent washer or dryer like Maytag and had to settle for Kenmore or some other brand that they figured was inferior. I noticed that they struggled through 20-25 years of maintenance free use of their inferior appliances. So when I found a pair of Maytag, I thought I had finally arrived. I was 60 years old and I knew this would be the last washer and dryer I would ever have to buy.It is now 2 years later and we developed dryer problems. The repairman found the computer malfunctioning and suggested it would be cheaper to replace than to repair. We asked him to check the washer while he was here and his diagnosis was similar. The drum bearings were gone and probably too expensive to repair. The Maytags are now in some scrap yard and I now have an inferior washer and dryer and I am looking forward to many years of maintenance free struggles. I used to think that Maytag repairmen are the loneliest people because their machines were reliable. I now know that they are lonely because all of the Maytags are garbage and not worth fixing.

Just got off the phone with Whirlpool Customer Care after getting the run around between parts and customer service for most of the morning. My issue is with the shelving on my MSF25D2EAS01 Maytag side-by-side refrigerator. The plastic surrounding the glass shelving is disintegrating and they are not admitting to a defective design only that the original part has been obsoleted and a new one is available for purchase (an over $300 expense to replace three shelves) on a unit that is just over 2 years old. I am willing to bet the old part has been replaced with a different design after they realized a substantial number of customer complaints. As an engineer, it is obvious to me that these shelves are poorly designed for their intended purpose, furthermore my work allows me to recommend appliance brands for large projects so I see no reason to recommend Whirlpool or any of its subsidiary brands (Kitchen Aid, Maytag, Amana, Jenn-Air) to any of our clients. Whirlpool quality and customer service is substandard and no better than any imported brand of appliances.

We bought a new Maytag Bravo washing machine last spring. It was easy to understand the instructions, but that is all that was good about it. Like everyone is saying. It doesnt wash the clothes completely. On every dark load I have what looks like streaks of lint. I contacted Maytag. They gave me suggestions for solutions. None of them worked. I have put the clothes on for a second rinse and spin and it got out some of the lint. Also. they are evidently spun so hard in the washer, after they come out of the dryer they are a wrinkled mess. All the wash and wear, which is almost everything we own, is wrinkled. I have to iron every item. Never again a Maytag for us. If there is a class action suit, I want in on it.

We purchased this model from Home Depot in February 2011. In July 2011, I found it full of water and dirty dishes after running a wash cycle. It was completely dead like it wasnt getting any power. I checked the fuses, etc. - nothing was wrong that I could find with the power supply. I called for a service tech that day and they sent someone out to check it. It was the control panel. They shipped me a new control panel and the tech came back to replace it under warranty. It worked great until July 2013. Again, it is full of water and dirty dishes, wont turn on and has no lights on the front panel. I called Maytag to get a service tech. The warranty is expired of course. They offered to sell me a replacement dishwasher at a discount for $409, Model # MDB7749SBW. Or I can buy an additional 1 year of warranty for $269. I also could buy a control board for about $150 online. None of these options is attractive right now, but hopefully if I get the new model, it will not have any issues... I wish they would just tell me it was a crap unit instead of giving me the option to either get a new one or pay for a useless warranty. I am fed up with this dishwasher. 2 control boards in 2 1/2 years is unacceptable and indicative of a defective unit or design. After reading the reviews here it appears to be a defective design.

This machine does a great job at cleaning clothes. The clothes are always great in color, and removal of removable spots. The cycles are not too long and the machine is not noisy. Machine is nice looking and water cycles can be normal or large.

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.

We purchased a 3K Maytag refrigerator/freezer and purchased an extended warranty as well. 5 months later the ice machine stopped working. We called Maytag to get it repaired since its under the 1 yr factory warranty and they sent an appliance service company they contract with to repair it. 6 service calls and two months later its still not repaired. I called Maytag back to say if you cant fix it please replace it. They say it needs to be deemed not repairable to even consider replacement and that they would send out a different repair company. As of yesterday (9/(9/14) another month and a half and 5 trips from the second repair company and it still does not work, so I call Maytag again to complain and they give me the same line ....needs to be deemed unrepairable... How long and how many service calls does it take to fix a ice maker? How much work and how many hours do I need to miss to get what I paid for? I went to their website and it talks about how their mission statement is customer service etc, etc, etc..... Thats just a bunch of lip service and judging by the HUNDREDS of complaints I have read this is their standard method of operation.... I for one will not let this go and will be filing a claim in small claims court to get what I paid for..... BE WARNED if you are looking to purchase a appliance.

I have a Maytag Neptune washing machine which had a mold problem on the rubber grommet. I have been trying to call Maytag to no avail. I researched and saw there was a class action suit for this very problem and I was never informed. The washer may pose a health hazard and I would like Maytag to do something about it.

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

I bought a new Maytag dishwasher installed by East Town Appliance in Wautoma, Wisc. They installed it and ran a full wash cycle and it worked fine. After they were finished, I got all my glasses out and put in their dishwasher all excited to get them clean and sparkling. I started the dishwasher, put on a coat to check my birdfeeders on the deck where I was standing in front of the patio door. I heard water running suddenly. Turning around to see water gushing out of the bottom of the dishwasher. I called East Town back and had the installers return immediately. The pump was stuck open. I called Maytag about what happened and they said they wouldnt pay for the floor damage because it was already installed and to call my insurance company which I did. They went after Maytag and won but I had to pay $500 insurance deductible. I will NEVER buy anything by Maytag again.

This washer came with the home we recently purchased. I used the machine and OMG the spin cycle is NOT quiet.. I posted a video of it on FB. A friend of mine who owns and operates an appliance center watched it.. messaged me back and said Do not call repair man as it is cheaper to buy a new machine... I knew this machine sounded like a piece of **.. I know I wont replace with the same machine.

We purchased a Maytag refrigerator Model # M1TXEMMWS02 and Serial # E01103420 in April of 2010 from Home Depot in Aurora, Illinois. First off, we did register the fridge online via Maytag which of course, they have no record of! Now, we go on vacation and come back to all of our food ruined because the refrigerator stopped working! No refrigerator should stop working within two years! I called Maytag and they offered me a Repair Plus One package of $302.73! Are you kidding? We paid $400.00 for fridge. Then of course, only one-year warranty and have to pay at least $75 for a service call, labor plus parts! If it’s the compressor, the charge is $326.20, plus shipping and handling! What a joke! There needs to be longer warranty and should offer free service calls and much more. I am disgusted in Maytag products and in which we purchased due to a reputable name! Never again.

Oh my god, I feel your pain, folks. My mother is sick in the hospital while I try to maintain my house with this totally POS refrigerator!! 3 defrost cycles to remove ice and now the service guy tells me that compressor is shot, 6 week back order for parts!!! Just two years old!!! Also had the same water overflow issue to boot 1 year after getting it. Maytag (whirlpool)- youre killing me!!!!

MF12665XEM7 - Maytag Refrigerator purchased from Home Depot. We initially thought it to be a good value until it started leaking puddles of water onto the floor to the front sides of the bottom freezer drawer. This event repeated itself and I feared the water would seep between the floor tiles and begin to degrade the sub flooring or possibly cause mold as well. Upon further investigation of lying on my side and pulling the bottom drawer open, I felt, what I thought to be ice on the bottom of the refrigerators floor. I gently inserted a smooth butter knife and with a nudge, a whole sheet of ice about one half inch thick, lifted from the refrigerator floor. I have since had to repeat this about every three weeks or so. Im nearing retirement and shouldnt have to lay on my floor like this to protect my floor and to keep my wife and I from a potential hazard of a slip and fall from this water on the floor! Dependability People? Hardly! I think they got outsourced! Im disgusted! Thank you!

We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

Purchased side-by-side with bottom freezer 2009 after Hurricane Ike. Fridge has stopped cooling. Called Maytag Customer Center and was told nothing can be done only to find theres a 10 year warranty on the compressor. This malfunction should not be an issue after 8 years. My GE fridge still works after 25+ years. Horrible!

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

As others have stated, cant wash more than a couple towels or 2 pair of blue jeans. The washer is useless. Purchased Maytag for quality and received crappy worthless machine. Maytag should take returns and refund buyers money!

Water ran out of washer and flooded my garage. 1) Replace computer. 2) Wrong computer. 3) Water still flooding garage. 4) May need water valve. 5) Showed up didnt know what to do, then left. 6) Whole new tub - 3 hour repair - 2 weeks until they have time to repair. Still waiting. HELP.

Purchased the Maytag Bravos upon recommendations from Lowes and Home Depot to replace a 20-year Kenmore that finally died. Since the Maytag brand was always considered to be the top of the line washers, we purchased the pair. About a week ago during the spin cycle I thought that a 747 was taking off in our laundry room. Called a local appliance repair service who said that there had been numerous issues with the Bravos series and to call Maytag to inquire about a recall. After 45 minutes on the phone with a very sweet naive young lady, she told me that the new models did indeed have a 10-year limited warranty on parts. However my 3-1/2 year old washer was not grandfathered into the warranty. I could (a) pay the $150 service charge to have someone come to inspect it or (b) buy a new one. I will be purchasing a new one but it will not be a Maytag or Whirlpool product. Now we know why the commercial for the Maytag repairman is not running... Hes now very busy working on their broken products.

The glass shelves stop 2 1/2 inches from the back of the refrigerator. Things keep falling down in back. I have a counter depth. Cant afford to lose any space. Freezer poorly designed for space compared to one I had before.

We bought our Maytag dishwasher less than 2 years ago (model MDB8969SDM0) and we are remodeling our kitchen now January 2018, and when we pulled the dishwasher out we found that the wire (12/2) had melted into the back panel. We won’t be putting this Maytag back in.

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

I purchased the Legacy series washer and dryer from Home Depot in 2005. For the first 3 years, the washer worked fine. Since then, it has all been downhill. When I use bleach, I have to run an empty load because for whatever reason, the bleach goes through to the next load which has resulted in a number of ruined clothes. The wash cycle leaves clothes dirty and some even come out partially dry?! The rinse cycle does not always work as more times than not, the fabric softener is still in the dispenser cup. The spin cycle is getting worse with each load. Sometimes I reset the spin cycle as many as three times at which point I hand wring the clothes. This creates a strain on the dryer as I have to run it extra long to dry the clothes. I am more disappointed than I can say. I will never purchase anything Maytag again and I will not purchase from the company who makes Maytag products.

I purchased a Maytag dishwasher delivered in dec 2012. We are snowbird Canadians and the dishwasher is only used 5 months per year. Jan 2015 the control panel quit working and the repairman tells me the wires on the control panel have started to melt down. He called Maytag and was told they had extended the warranty on this machine for one more year. Missed it by 2 months. Considering this was only really used one year, I am very disappointed. How can an extended warranty on a safety issue only be for one year? This is my first Maytag product and will be my last. I only purchased it because I was told Whirlpool bought them out and I have never had a problem with Whirlpool.

I purchased the Maytag MDB8959SBS dishwasher back in 2014. I have historically been a Bosch guy when it comes to dishwashers but I have been so happy with my Maytag Maxima washer and dryer, I wanted to give their dishwasher a chance. Well, it has been a major disappointment, to say the least. For starters, it just doesnt clean that well. I am very careful in how I load a dishwasher. I do not put baking sheets across the bottom rack lol. Consistently we find dirty dishes. Then after about a 6 months, I noticed the paint on the adjacent cabinets were peeling in spots (near the top and bottom corners). I started feeling around the outside of the door during the wash cycle and there was a fair amount of moisture collecting around the outside of the dishwasher seal (or non-seal). Fast forward to about a month ago, I noticed a burning smell in the kitchen while it was running. Did the typical check the heating element routine thinking something fell down and was burning. However, it was perfectly clean. Emptied it completely and ran a totally empty load. The smell was still there. I eventually figured out the smell was emanating from the upper right corner of the door. Coincidentally this was right above the location of the control board. I grabbed a tool and carefully removed the front panel and discovered wires were melted (some fused together) and even the inside of the panel (which is plastic) was melted in spots as well.So yes, I could have contacted Maytag and sent pictures and fought with them over a repair but to be honest, I have no interest in keeping this appliance. It has been trouble since day one. Again, to be fair, I have had good luck with their other appliances but this was an awful experience and a total waste of money. I have since gone back to Bosch and could not be happier.

I bought a top end Maytag refrigerator with the freezer in the bottom drawer. Spending the extra buck was something that I thought was worth it, being a Maytag. Fifteen yrs go by and it stops completely. It cost me 200 bucks for a service technician to tell me that the compressor or it has a leak. Its not worth repairing. With todays cience and technology, you would think that they can make a refrigerator last for 25 yrs or more, like the old ones. We went to the moon 44 yrs ago. Why cant they make them to last? I think that the corporations figured they can make more money making an inferior product that needs to be replaced every 10-15 yrs. I will never by a Maytag again.

My 16-month old dishwasher, which is not being used everyday, broke its control panel. Maytag will not fix it for free because they only back it for one year. This is a major appliance, shouldnt it last more than 16 months? The cost to repair is almost as much as a new dishwasher.

Me and my wife bought a Maytag refrigerator from Home Depot. The top half freezes up in a big way and it gets real frosted up I have to pull it apart every 2 months to defrost it. The bottom half starts to get warm if I dont do that. I will not ever buy another Maytag refrigerator again.

Called Maytag. Was part of 2005 recall with Neptune Maytag washer. We did not realize it and now Maytag will not do anything. Now having dryer issues with a cracked drum. Called and there was no resolution or attempt to resolve.

I inherited this Maytag washer, so it has been around a very long time (I have had it for 18 years). It still runs quite well, has 3 levels of wash/rinse, 3 cycles to wash in. Both of us...me and the washer are still kickin together. Highly recommend Maytag.

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

I bought the Bravo XL HP Washer and Dryer in 2014. Dryer is great but the washer just after having it 1 yr started making awful noises. Had a repair man come which cost me money and was told the bearing went out and I needed a new one. He said it would cost over 700.00. I didnt fix it as I could buy a new one for that price. I did that. I hate the washer. It doesnt get the clothes clean and the cycles are long. My clothes dont feel or look as good. I have to leave the top open or it smells awful. So, I got the new washer 1 yr after the other one in 2015. It is now 2016 and it is making noises. Theses washers need to be recalled and we should be able to get a different one or our money back. Please, do something about these washers as a lot of us are stuck with them.

I have had to replace the control panel on my Maytag Dishwasher 2 times in the last 4 years I have owned it. I diagnosed the problem using the serviceman repair manual which is located on the kick plate or lower plate for panel of your dishwasher. This is not one of the dishwashers that is listed on the recall list, but it is on the dishwashers list that Maytag suggested that you buy to replace your dishwasher that is on the recall list. Model number mdbh9898awb3.

I purchased this gas range from Home Depot in 2011. From the beginning I had problems with the cooking racks slipping off the oven wall. In some instances hot liquids poured on the oven floor. I had bought a service contract on this product and when I asked that this be repaired I was told that it was not covered as it was a design flaw. The condition has slowly worsened and now I cannot cook anything in the oven for fear of the racks falling down. This is a safety feature and the oven should be replaced my Maytag.

Our washer, still under 5 year parts and labor warranty, wasnt functioning properly. We went through proper procedure having repair personnel first attempt to repair; waited over allotted time for replacement parts, wanted to attempt to repair again, then to replace with sub-standard model. We are now in our 5th month of being told 3-5 business days, 10-14 business days, and I was just told it will be weeks (after waiting 19 days) that replacement will return our call as they are 4 to 6 weeks behind. I have pages documenting dates, times, names, departments and excuses. What can I do at this point? What are my options?

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

My Maytag Refrigerator Freezer model MFI2569VEM4 started leaking water into base under bottom freezer door. It then fills up and freezes into solid sheet of ice and overflows and leaks into floor. Ruins Hardwood Floor. BEWARE!!!!! I have now seen several similar complaints online. Mine started doing this less than 2 years old!!!!!

Mine is the Chrome Maytag four-burner cooktop model. About $700. I installed it with ease. After two years there are only one or two slight scratches. It sees full meals for two cooked daily. The grate is first class and looks new, the top itself is easy to clean with a damp soapy cloth and mineral oil. There is easily enough BTU power for any size of pro pan. The igniters are healthy and fine and a repair would be easy.

Have had Maytag HE washer for 4yrs, so far it has broke down three times. I contacted Maytag and they asked if I had bought extended service contract? No I paid $700.00 for this washer and had expected it to work a little longer than 2yrs before seal in door is cracked. Would NEVER buy another HE or Maytag product again!

I purchased your refrigerator (model #mfd2561heb) in 2005. I bought a Maytag, because I thought it would last me a lifetime. I came to find out it will not. I called Maytag, and got Repair Plus One. The repairman came out without a compressor or capacitor. Now, I have to wait 4 days or more. I have a 3 year olds birthday party, of which we will be working out of our 19 year old Kenmore in the garage, which has worked flawlessly. To make it short, you lost me as a customer, because of this product! I just wanted to let you know. It is sad too, as we enjoyed the refrigerator. Its been making noise for awhile. I thought it was just part of the ice maker. Now, it cost me another $299, plus all the food I had to throw out! There was a big recall of refrigerators from Maytag around the time mine was made. I think that this model should be part of that recall as well. Dont buy a Maytag! They may have had quality at one time, but I just think those days are gone. Thank God for our Kenmore in the garage. I dont know what I wouldve done without it.

Maytag washer Model #: MVWX655DW - I purchased this machine at Lowes in May of 2016. Always was a loud machine but seemed to work ok. In April 2018 the machine stopped working correctly. The spin cycle would lock up and not finish leaving clothes soaked. Called Lowes and waited for their repairman. He came and said it was the clutch and drive motor. Repair is over $400. Machine is worthless. Huge mistake. Never buy a Maytag. I called Maytag to see if they would warranty it. They basically said, Sorry only a one-year warranty on it. I told them the reason I bought it was it had 10-year warranty on it. They said only certain parts but its the drive motor that is clearly marked on the machine that has the 10-year warranty. I was told, No sorry. What huge waste of money. I am out close to $600 and Lowes only give you a store credit with their protection plan.The credit is not enough to purchase another machine without more out of pocket expenses. I will never buy another Maytag and I would not recommend anyone else does. Their warranty is a huge joke. Their customer service is terrible. Maytag should not even bother sticking the 10-year drive motor warranty on their machines. They do not honor it. My advice do not even consider buying one. You will be out the money and be purchasing a new machine within two years.

After reading several of the reviews, it looks like Maytag doesnt get it - or maybe they do and its a plot to make more money. Our dishwasher model MDB8959FSZ4 was installed in Dec. 2016. Within the year, it started leaking. After many service calls it was determined that the arms holding the upper rack were not installed properly and were pushing against the door and water was coming out. After that was replaced, weve had 2 years of relative good use. Now, it wont empty and that started after smelling something burning. The burning smell has gone away but it wont complete a cycle. Service tells us its the drainage pump and that will cost nearly $500 to replace. We wont be spending another dime on this piece of crap. Well replace it with NOT A MAYTAG. Im wondering if it has to do with the control panel as many others have mentioned. We dont care to find out at this point. We are buying something else.

My husband and I bought a set of Maytag appliance 12/2011 the washer squeaks real bad on spin cycle and now today the dryer started making real real bad squeak sounds to the point I can not use it!!! My appliances are only 4 years old!!! And we wash clothes once a week for just my husband and I. I would not recommend buying any Maytag appliances!!! They are supposed to be the best but are not worth **!!! And I called Maytag, they are not willing to help. Bad service!!!

They are coming for the 7th time to fix the ice maker. Three full replacements. The bottom of the freezer had a buildup of ice, another call to repair. I know where the Maytag repairman is, hes at my house.

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

My Maytag Neptune washer also has a problem with mold build-up and now the door lock assembly is totally gone. I was unaware of the class action suit or I would have joined. I am just disappointed!

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

Model #MDB8959SAS1 MAYTAG Dishwasher - purchased in 2014 at Home Depot. First we had to replace the rack adjuster, and after that another part broke. Finally, the electrical control board totally melted and smelled up the house. Fortunately our breaker switch worked and it didnt cause a fire. But Ive read other reviews of this happening with Maytag dishwashers where there was a fire. It now resides at the landfill.

Maytag Performa Side by Side fridge PSD262LHEB door handle pulled off for the second time since purchase but this time, the handle knocked over a pot of hot water on me. I am just relieved that I have no small children anymore. I would consider this very dangerous in any household. The first time, it was covered under warranty along with the broken ice maker. The repairman stated that he had replaced many handles and due to design flaw, they would not last long.

We bought a Maytag refrigerator two years ago with the front french doors and bottom pull out drawer. We chose Maytag because we thought it was a name we could trust, a good quality merchandise. However, in the last two months, we started having problems when the fridge wouldnt stay cold, the freezer worked fine. We removed everything from the freezer and my husband found the freezer needed defrosting as the back of the unit was a solid sheet of ice. It took hours to defrost and we thought that we had the problem taken care of.. and that we wouldnt have to worry about this happening again. However, we have now had to do this three times in the last two months!! I love the style of this fridge..but am getting SO ANNOYED with having to rip everything out of the freezer and spending HOURS to defrost it! I have NEVER had this problem with any other fridge!! Im ready to replace it, but weve only had it for two years, and I shouldnt have to be spending a fortune on ANOTHER fridge after TWO years!!

The washing machine is rusting and Maytag refuses to take care of their inferior product and obvious inferior materials used, and also inferior workmanship.

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

Both my washer and dryer are Maytag. Dryer element shorted out but was still under warranty so was fixed. Washer is very loud and now makes a rattling sound. Every so often it will hang in the middle of a cycle and the lid wont open until I unplug it.

We purchased a MDB8949SAW dishwasher in 2013. 1 month after the warranty expired the touch buttons went on it. If you selected normal it would opt for something else like rinse only. We researched online and my husband followed instruction online to take the door off and seal the moisture to prevent this from happening. This worked for about 2 months and now back to the same thing. We paid $500 for this and just living with the problem for now. All we can do is warn others.

Bought this Range in March of 2019. I really liked the large oven in it. Right away I noticed that the oven didnt back things very uniformed and very quickly, so a lot of burnt cookies. But I adjusted to that, not super happy about it but it was fine. Tuesday while cooking the cooktop suddenly went out. I had been smelling something strange the last couple of times I had cooked with the oven and cooktop on so I just assumed it was the oven, it did need to be cleaned. Well I ended up pulling the range out from the wall and taking the back metal piece off...the wire running to the cooktop was burned, like 3 inches up the wire and also the wire coming into that wire on the range cord. Just destroyed. I was shaking. My house could have burnt down.I just attempted to call Maytag, knowing my warranty is up (1 year) but thinking they should know about this issue. I was told that they would need to send out a certified tech would need to come out to access the situation...ok...when are they available and she said the 29th of December, really? How many people can go 3 weeks with no oven? I take care of my 93 year old neighbor and make dinner every night. So obviously I cannot wait. I have a tech coming today to fix this fire hazard. I was told there was nothing that can be done as it was not under warranty anyway. What so your certified tech was going to come out for free and then charge me what I probably paid for the range to fix it.

I purchased a Maytag dishwasher on Nov. 5, 2013 from Freds Appliance. I had to have the control panel fixed twice and it failed again in June 1916. My stemware had a film on it and I either had to wash it by hand or rinse it in hot water and dry by hand. Thus I felt like how could my other dishes not have this film on them even though I faithfully used Finish. I have 2 daughters who live within a half mile of me and they did not have this trouble with their dishwashers. I always felt Maytag was a top brand, but I replaced my 3 year old Maytag with a Whirlpool that my daughter and her family of 4 used for 19 years. Guess what... my glasses come out sparkling without using Finish and they wash in half the time and are dry!

One baffle broke off in my washer. Very disappointed in this Maytag Model #MHWE201YW00 Serial #HL20102420. I purchased this in Sept 2012. Where the baffle was hooked on had sharp fins sticking out that ruined my 2 small rugs - shredded them.

I have had nothing except trouble with my new Maytag Bravos washer! I first had a suspension arm or something like that replaced along with the agitator. My water cycle has never worked correctly since it was new. I take out the clothes and half are still dry. My daughter washed her kids’ clothes in the washer while she was living with us and the stains did not come out. She thought that is really unusual since they werent stains that normally you would see left on the clothes. I went to my father-in-law’s house (they have a front loading Bosch), took her detergent with her that she used here and guess what? It’s just one washing and the stain was gone. She had washed the clothes in our washer at least 7 times trying to get out the stain. Now, we have such a loud noise that it sounds like it is going to take off. Then, the bottom of the washer started to leak. We took it out and checked it and we cant find the leak. The clothes smell awful when they come out of the wash. I dont know if it is bacteria build up. I use the cycle cleaner when I am supposed to. This is so sad. This is the first time I have had matching washer and dryer and I wish I would have kept my old Sears model that worked great. I havent decided if we want to fix it. With the price to fix it, I can buy one I might like. Never will I buy Maytag again or another Whirlpool without checking out the reports.

My $1,500 Maytag double oven Gemini has been trouble from the get go. 1st, trying to broil something cannot be adjusted. It sits 3 to 4 from the fire & there is no 2nd shelf. The control knobs sit on top of the stove & its easy to burn them when cooking. The broiler has always smelled like its leaking gas. Plus, the bottom oven stopped working & we had to get it repaired. The last straw was when the control board went out. We arent even going to try to repair, just going to buy a new stove. No Maytag!

Did not know of the lawsuit or recall. Now I have to buy a new washer after fixing it out of pocket and mad that cant get part of the settlement. Not ever going to buy Maytag again!!

Control panel is defective on my Maytag dishwasher. Found a phone number that was created to deal with this problem. I only had to hold for a few minutes but the first person I spoke to was rude and unhelpful so I asked to speak to someone else. When another agent came on the line I told her that only the normal and rinse button light up but do nothing when pressed. She arranged for a repairman to come to my house and determine if my control panel is defective at their cost. When he arrived he asked me what the problem was and I said, The touch pad control panel is not working. He stated, Your control panel needs to be replaced. I have to order the part and come back to fix it. He was there for about five minutes and he never laid a finger on the dishwasher. When I asked if the control panel design has been fixed he said, No, you will probably have to replace it again.There is a video on the internet that shows how to seal the electronics with silicone. The repairman said that they cannot seal the electronics unless Whirlpool provides a kit to do it. I guess the Maytag repairmen may have to come out of retirement. My husband will seal ours after it is replaced so we hopefully dont have to deal with this problem again. So now I am waiting to see if he returns in a reasonable time frame and gets my dishwasher going. There is a class action suit about this issue filed in 2013 about this defect.Updated on 09/23/2015: A repairman came to my home on August 20, 2015, at Whirlpools cost, and he determined my touch pad did not work. He informed me that Maytag would provide the part, free of charge, but it would cost me 85.00 for them to come back and install it in 2-3 days. As of today I am still waiting for the part to come in, apparently due to high demand Maytag was out of touch pads, which were out of stock. No idea of when that would be, the repairmans company said, dont call us, we will call you when the part arrives. So I began to look for the part myself, found a couple on an auction site, but most companies that sold parts were on backorder. Until I found a company that said their inventory was out of stock but they had five, stashed in the back. The price of 105.00 was not that much more than the 85.00 cost for the service call. Got it in two (2) days, installed (in about five minutes), sealed by my husband and I loaded it and washed my dishes. I was so overcome with relief, tears came to my eyes and I almost fell out. I give five star to the fella that had the part stashed until I needed it.The Maytag repairman is still waiting for the part so he can fix my dishwasher.

I purchased Maytag Bravos MVWX500XWO top loading high efficiency low water washer and it is a piece of junk. All my clothes came out horribly wrinkled and ruined a white jacket when I used the color safe bleach dispenser. I purchased the machine from Sears, where I purchased the extended warranty. I had an A&E technician out and he explained that the new technology of machines are expecting all clothes to be dried in the dryer. Okay, but what do you do with clothes that say hang dry and they come out so wrinkled and twisted that even an iron cant get the wrinkles out? Another suggestion from the technician, put the hang-dry articles in the fluff cycle of the dryer. Well, thats a big nugatory since they are supposed to hang dry them. Supposedly, this machine is all about energy efficiency but isnt it a contradiction when you are using more energy with running a dryer? Someone suggested to me that perhaps there wasnt enough water being dispensed during the spin cycle resulting in horribly wrinkled clothes. Either way, I am on my last nerve with this machine. I always thought that Maytag was an elite company. Well, how wrong I was! Their customer service is pretty much not customer-oriented. Its all about the almighty dollar. After speaking to a supervisor, she explained to me that I should contact Sears with my complaint that Maytag had no recourse. Well honey, Sears did not make the atrocious machine. They are just the so-called messengers. I have unfortunately found that once Maytag sells their horrendous product, they dont even stand by it. Now isnt that typical of companies nowadays and sadly, lacking with this company? Pride in their workmanship! And again, its all about the almighty dollar and who gives a ** about customer satisfaction? Maybe thats why they dont have the Maytag repairman. He was ashamed to be associated with this irreverent company.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

We purchased a Maytag refrigerator model # 1TXEGMYWOO. The refrigerator part froze all of the food in it. We moved the temperature selector to the last place (two notches away from the recommended setting), and the food still froze. The furniture store we purchased it from replaced it with another refrigerator (same model). And that one did the exact same thing. We had to throw out more groceries. Obviously, this model is defective. We are now waiting for the store to replace this one (with a different model and brand). They have been very good about trying to make things right for us. Maytag, however, is a different story. They were very rude and indifferent when I called to complain. Their policy is to repair or replace the part (temperature gauge). I dont want a new part. This is a new product. And I bought it expecting it to work. I have had to throw hundreds of dollars worth of groceries away. I was very disappointed in their attitude. I will not purchase another Maytag item again. They used to have a good reputation. They now sell inferior products and do not stand behind their products.

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

Washer sounds like gearing is broken, is noisy during operation, various combinations of options dont work, appearance of only one agitation cycle combination on washer, just many settings but all with the same response; dryer does not timely dry clothes, all settings default to the same palpable heat temperature; clothes take much longer to dry in new dryer than they did in old Maytag. Newer Maytag set appears to be secondhand garbage sold as new by Menards. Company unresponsive to complaints.

Never buy from Maytag. I and my daughter bought from them two refrigerators of them. After one month my daughter started to fix. I am started after one year or it is leaking. Our freezer destroyed and realize this after one day all my food I throw away. The same was with my daughter refrigerator. My daughter have old refrigerator it is working without problem for 50 year never fixed. Never ever buy from them anything. It is good I was at home. Sometimes I am traveling if it happens this time. I do not want to think about this. For fixing you have to pay lot of money. I hate that I purchased something with them.

Omg I am so shocked at all the complaints about these refrigerators.. I too bought refrigerator, stove, microwave, dishwasher from Lowes after a storm just about destroyed our home. I was so excited to have such a beautiful refrigerator and new kitchen...but shortly after it started freezing on the bottom of freezer and leaking all over. My new floors and kitchen cabinet are ruined. Every other day we have to break up ice and clean it out from freezer.. it still then leaks.. several family members have slipped and hurt themselves. Please if anyone knows how to get it fixed without it costing us a fortune let us know. Maytag (Whirlpool) knows it is a defect... Why will they not fix it? I cant afford a new refrigerator and shouldnt have to after only two years.. If a class action comes up.. please contact me. Shame on them...

I would say you have plenty of options when choosing a color for your dishwasher. You can choose black or stainless. Try one today you wont be disappointed. I load plenty of dishes into the space. It has extra pockets for little things and it has plenty of hooks and hangers to use for bigger cycles. Kenmore Dishwasher runs great. Very efficient and cleans the tough stains better than any dishwasher Ive ever used. I would recommend this to anyone looking to buy a dishwasher. Of all the dishwashers I researched at Lowes and Home Depot and Sears and Ace and other local stores, the Maytag was the lowest price with all the features I wanted.

I am angry at my Maytag! It sprays water on clothes that is not enough to soak them or let the detergent to be dissolved especially for towels. Hopelessly, I Hand Wash my towels, rinse in tub then just put them in the machine to spin. BAD BAD :( :( Is it possible to increase the water amount?

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.