This Maytag dishwasher works great if you are using as a sanitizer for your dishes so long as the dishes were soaked already. It stinks if you do not use it often and requires a lot of bleaching.

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

I have bought a new Home Depot Maytag Impeller HE washer. After 6 repeat washings of 2 items that are lightweight dark brown it was obvious after drying they had soap and lint and lot hairs on it. I reached with no he detergent. The last 4 times the water level filled to 1 depth even for high level water setting to extra rinse or power wash settings. I went to Home Depot and they suggested I call Maytag repair center on Tuesday after the labor day holiday to have them check it out. I will also call the supervisor at Home Depot as I do not feel paying $600 for a faulty machine is acceptable.

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

I bought a new washer and dryer on Sept. 9, 2011. Front Load Commercial 2000 Series. I have had Lowes to my home 2 times since it was delivered because it shimmies across the floor. I am very upset with the purchase of the Maytag front load washer. If you could please get back to me on what can be done. I would like for a representative to contact me and come and look at the situation.

The washer that always needs repair! My first problem with my Maytag washer was that the sensor needed replacing (wont wash or spin). Since then I have had the sensor replaced and motor replaced. Today, I had to call for a service call, and was told that I have to wait over a week! Bad customer service!

Maytag 6.2 Induction Freestanding Range Model MIR8890AS0 F47 - I am a very careful shopper. I spent many, many hours researching and searching for the best value. It took me over 2 weeks of research to find an induction oven we could afford. We are a family of 3. Normally, we use just one burner for dinner. We bought the range in Feb 2013. On August 5. 2014, we had company over for dinner. I used more than 2 burners and the oven at the same time and the right 2 burners quit working; I now have the dreaded F47 code. I have had numerous Maytag Authorized repairmen out. They ordered every part except for the one that was necessary to fix my stove. I purchased in Feb 2013, burners went out 8/5/14. This is only 18 months old and is JUNK. Arent our landfills full enough?Maytag customer service is awful. I spent hours on the phone, mainly on hold, in efforts to get help. Maytag claims to have such a great 10 year limited warranty but they wont warranty this F47 issue. Thank God I bought insurance with an outside company. The wrong parts that were ordered were at least covered by my own insurance policy; no thanks to Maytag. I am angry that I have to search all over again to try and find the right stove. I am now fearful of induction. I invested in a lot of induction cookware which was an added expense and burden! They need to stand behind their appliances!People cannot afford to waste thousands of dollars every 1.5 years to cook their meals! This has been an extremely unpleasant issue. It has cost me many hours of waiting for repairmen, waiting on hold, getting and storing many wrong parts ordered by repairmen. I calculate this cost me over 50 hours of my life on the F47 problem. Not to mention the time it took me to shop for this junk to begin with!I think they need to recall this issue as it is clearly a design flaw. I researched this and found many other owners had similar problems. The F47 means that the user interface isnt communicating with the range (the circuit board). They placed the circuit board under the burner surface area, sandwiched between the burners and the oven. It was just a matter of too much heat before this board shorted out. The cost to replace this board is over $600. I am afraid of investing another dime into this machine. I wasted time, energy and A LOT of money on this inferior product.

The dishes need to be washed off to be sure they will be clean. It holds a lot of dishes. You can put it on a short wash or long one. Leaves water on base of glasses sometimes. Holds moisture. Heavy wash, normal wash, light wash, rinse only, auto clean, delay 1-9, heated dry, sanitize, tough scrub, extra rinse. Regular size 24. Beige color. Electronic buttons. Maytag Quiet Series 200: I do not like the racks for putting dishes in. Otherwise it holds a lot. It does not clean dishes if you do not rinse them off first. If you run the dishwasher immediately after putting dishes in it will clean them off. Sometimes it leaves water standing. Even with what I have said I really like this dishwasher. We have had the dishwasher a long time. We use it at least 2 times a week.

I bought the largest Maytag top load washer. From day 1 clothes come out with laundry detergent left all over them. I have to take a washcloth and wash off every piece of clothing coming out of the washer. Had a technician come out. He said he gets this complaint every day. His suggestion, put less clothes in and use less detergent. This washer is programmed to use minimal water and it just doesn’t have enough water to clean all the detergent off. So, I bought the biggest washer to wash bigger loads and now you are telling me that just doesn’t work.Spoke with Maytag customer service. They said very rudely if there is no problem found when the technician came out, there is nothing they will do. She told me it was user error. My dryer also stopped working. Sometimes it would turn on, sometimes not. The technician said the lint screen error code came up. He would try to get Maytag to replace the whole board but usually they don’t do that unless the whole board has a problem. Called Maytag the next day. The technician documented he fixed a connection problem and closed the ticket. What???? So, now I guess I need to schedule another service visit. Very unhappy with 5 month old appliances. Paid $1700 for the pair, you expect quality products.

I bought my Maytag Model LA608 washer in 1976. It has very few electronics and a mechanical timer. It has been used every week since then for 2 or 3 people. It has had 3 problems in its lifetime. I replaced the 2 valves that control the hot and cold water entering the machine. I replaced a small plastic sprayer part. And last year I replaced 3 clamps that rusted and started to leak. Thats it in 40 years. I was able to open up the front and back covers to get at the parts quite easily.It is a simple machine with almost no electronics to stop working. Nothing bothers me about the machine. Its simple and wonderful. When it finally breaks, I will try and find a good sized machine that washes permanent press and regular clothes, has a controller to select hot/cold/warm water temperatures, has a regular and gentle cycle, and has 3 load levels for the water to be used. I will try to find one that is good quality with few electronic parts. I will not buy a high efficiency model that uses less water as I am on a well and water shortage is not a problem where I live. I will not buy a front loading model.I would not buy a machine that has options that I do not need. I would hope to find a quality machine similar to what I have now. I would read as many ratings about the various models before making a selection and then I would cross my fingers and hope for the best. If it is possible, try and find a good quality machine that will be dependable over time. Buy a basic machine with only the options that you really need. There will be fewer parts to stop working.

Purchased standard Maytag refrigerator w/ freezer on top in 2012. Freezer has never been able to keep ice cream. Never called for repair because after reading several of these complaints, mine seemed to be a minor frustration. However, I am waiting for the other shoe to drop.

I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

The dishwasher doesnt clean and the dishes and silverware come out greasy. What a piece of crap.

I have a Maytag Bravos washer and on almost every other load, the dark clothes (mainly slacks) come out with white splotches on them and then I have to re-wash the pants and the splotches go away. What could be causing this? Im tired of washing clothes more than once. Its incredibly wasteful and bad for our environment. Thank you.

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

I purchased the Legacy series washer and dryer from Home Depot in 2005. For the first 3 years, the washer worked fine. Since then, it has all been downhill. When I use bleach, I have to run an empty load because for whatever reason, the bleach goes through to the next load which has resulted in a number of ruined clothes. The wash cycle leaves clothes dirty and some even come out partially dry?! The rinse cycle does not always work as more times than not, the fabric softener is still in the dispenser cup. The spin cycle is getting worse with each load. Sometimes I reset the spin cycle as many as three times at which point I hand wring the clothes. This creates a strain on the dryer as I have to run it extra long to dry the clothes. I am more disappointed than I can say. I will never purchase anything Maytag again and I will not purchase from the company who makes Maytag products.

I purchased model number MF12067AEW in 10/07. Motherboard has been ordered to be replaced. I have been waiting 2 weeks for the board--all over the Xmas holidays without a refrigerator! We bought this model and paid $2,800 to have a counter-depth refrigerator. I will never by anything from Maytag again. We are holding our breath to see what the cost will be and if it will it break down again. We lost all the food in the top. Ice machine flap continued to pound open and shut all the time.

Wish I would have read the many, many, many reviews on the Maytag MDB8959SBS dishwasher before buying it. As noted by others, the touch control buttons stopped working 1 month after the 1 year warranty expired and Maytag wont do anything about it. BE WARY OF THE 10 YEAR WARRANTY CLAIM - IT DOESNT COVER THIS PROBLEM. Maytag should issue a recall on this product and do the right thing - take care of customers like they used to.

In 2011, I purchased 2 Maytag dishwashers, one for my tenant and one for myself. In 2014, the circuit board on my tenants dishwasher failed, when the unit was only 3 years old and of course out of warranty. I first contacted a local repair person, and he informed me that the repair plus service would be close to $300. When I contacted the company, after about an hour on the phone, they agreed to send their authorized repair service person and after his evaluation, would repair the unit with no charge to me, as a courtesy. This whole process took about 2-3 weeks. I felt that was fair. It is now 2015, and my unit, which I purchased at the same time and the same type, now is not working due to a faulty circuit board. My tenant uses her dishwasher more frequently, and that is most likely why her circuit board went first. This is a design flaw, or perhaps planned obsolescence. At any rate, Im not happy with this, and my model is mdb7809awb2, and serial # is FO4205659. Do you know if there have been any other complaints on this? Thank you for your help.Updated on 07/30/2015: After I wrote my review, I contacted Maytag about the problem. After considerable wait times, I spoke to someone who set up a diagnostic repair call, giving me the impression that Maytag would cover it. When the repair company called, they told me that I would be charged $104.95 just for diagnostics. Labor and parts would be additional. I called Maytag again, and they agreed to let the repair company charge back the diagnostic fee. After diagnosing the problem, it was determined the problem was the control panel and not the circuit board. The cost to repair with tax came to $315.85 and it was only this low because the repair company waived the return service trip. I can get a new dishwasher for a little over $400.00. I am very disappointed in Maytag, because I remember the commercials where the Maytag repair man was bored because the products were so dependable they never broke. My unit is only 4 years old, and its sad that it costs so much to repair it.

Worst Washer ever...hated it from day one of receiving it (but couldnt return because moving into new place, took awhile to get it installed, and by then the 30 day return window had lapsed, so now stuck with this piece of garbage!). Is ALWAYS off balance whenever you wash anything of weight (i.e.: towels, sheets, blankets etc.). It takes me close to 2 hrs to get these items washed because I have to keep starting and stopping it to try to get it to spin dry because it ALWAYS throws the items so is off bal. and wont spin. Then when you hit pause, adj. bal., & start it again, it starts REWASHING the items (instead of continuing on from where you left off), and sometimes when it cant balance in the spinning cycle it just shuts down making you think the full cycle is complete, only to open up the lid to find your clothes all sopping wet. Also, NONE of the cycles will get any of my clothes clean...it just uses so little water your clothes come out feeling grungy and still dirty. I have had to resort to ONLY using the BULKY cycle because it is the ONLY cycle that will use a higher water level (mainly because bulky items like towels will absorb the water so it needs to add more). With this cycle at least my clothes dont FEEL dirty when they are done washing!There is no way of knowing how much time is left on any of the cycles, which is a real problem when you have to start and stop it, because you really have no idea how far back it goes to start itself up all over again. There is just no way to time it, because it keeps messing up where you have to keep stopping/starting it, and then you have no idea of time frame. Never saw a machine built so UNUSER friendly!I will NEVER buy a MAYTAG washer again, and NEVER will I buy a washer unless it HAS the center agitator, and a control for water level. These HE washers are the worst, and unfortunately they are now the only washers being made, but without water, clothes just DO NOT ever get clean anymore no matter which fancy and expensive detergent you use. HE washers are HORRIFIC. I may just buy an old style used washer with the agitator... at least I wont be wasting energy to only wind up with STILL dirty clothes when using HE washers! FINAL NOTE: AVOID Maytag HE Washers at ALL COST! You will be sorry if you decide to purchase one!

MAYTAG HAS ALWAYS BEEN MY W&D MACHINES OF CHOICE! In my opinion they are the most reliable, dependable machines on the market - for years! I would NEVER by another brand of either washer and/or dryer.

Had a Maytag washer, 3.5 tub, stopped working. The motor upper bearing lost it press, drive shaft dropped 3/4 inch and locked against lower housing, stripped out pump spline. No f/u by Maytag after many attempts. This is a design flaw, the upper housing is so thin, if it had .001 press on it I would be surprised. This flaw resulted in a cascade failure of motor and pump.

Maytag Dishwasher purchased for $634 on 7-6-12 from Lowes. Control panel malfunctioned in August 2014. Started leaking in April 2012. From the online comments, I am trashing this machine. It is not worth fixing it and having it malfunction again. Maytag will not say anything about this, only offers a repair person out to fix. I am very disappointed that my hard earned money purchased a sub standard machine. Maytag used to mean reliability. NO more.

Maytag french door bottom freezer model #MFF2558VEB5 - It stinks to read all the similar problems Ive had with my unit. Purchased Nov 2011. Problems started within a year. First minor, deli drawer broke. I use clear duck tape to operate it and that has been fine. But not acceptable. About a year ago the water leak out of bottom freezer was noticed. The bottom inside is frozen sheet. I break up and manually remove quite often. NOTE: I intentionally do not use, did not install, the ice maker - historically they are poor risk so I dont bother. The ice unit is in the machine but not installed. I assume my water build up which freezes on bottom related to poor design of defrost drain and that is supported by other comments here. I find it disgusting. Live and learn. Its B.S.

Bought the Maytag high efficiency washing machine with the auto-sensing and deep water wash feature. It took some getting use to because of all the washing choices and different noises it makes. Auto-sensing seems to use very little water which is strange but clothes seem to come out clean. Best bet for me is like the old school way and use deep water wash and light load which is shorter and thats most efficient power wise but will use more water which is fine by me. Also bought the matching dryer and thats a 5 star review. Excellent product.

I would not recommend the Maytag washer with the large tub. It does not clean your clothes. I called Maytag and they do not care as long as it uses as little water as possible! Not a good value for the money!! That was the first time and last time I buy a Maytag... Thats the last $5000 they will get from us!

Purchased MBF1958 model refrigerator July 2012. Has had 3 major problems. 2nd time the compressor has failed. For over 1 month have been playing phone tag and given the runaround by Maytag. Never return calls when promised and get a different story with each person I speak with. After 2 service calls to diagnose a bad compressor, $69 service fee, two weeks for the replacement to come in, the third serviceman decides this is not the problem and the refrigerator cannot be fixed. Maytag has once again offered to SELL me a replacement at a discounted price. Do I really want to subject myself to the HORRENDOUS MAYTAG EXPERIENCE again?

I bought a Maytag refrigerator model MBB1953XEW three weeks ago. According to its features on the Maytag website, its supposed to be quiet (QuietSeries 100 sound package). Ha ha, make me laugh. Its the noisiest refrigerator Ive ever had. The repair guy checked it out this morning. He spent about 5 minutes running some sort of test with the help of his iPad. He then told me everything was perfectly alright, the noise was normal for a Maytag, and that I was going to get used to it.Needless to say, he had a totally condescending attitude. Its the first time I ever bought a Maytag. Previously, I had a General Electric that was noisy but not as much as the new Maytag. Prior to that, I had a good old Kenmore that was perfectly alright but that I had to give away for other reasons. This time I chose Maytag because I thought it was good quality and I wanted it to be very quiet. Well, nope. Next time, for sure, it wont be a Maytag.

Faulty Maytag MDB8969 Dishwasher - BEWARE! Whirlpool, Jenn-Air, Amana, Maytag, KitchenAid... Are all brands that fall under Whirlpool. According to Better Business Bureau statistics there is less than 1 chance in 10 that you will get the Whirlpool product you are expecting! We purchased a new Maytag dishwasher at the end of 2016. Within a couple of weeks the dishwasher began failing: discharge pumps, heating elements, soap dispensers, door leaks, faulty racks, rinsing problems... Since purchasing the machine we have had to make 7 different service calls, all under warranty. The warranty service providers have been good but the machine has been a catastrophe, having been out of commission for several of the 18 months since being installed, and causing serious water damage to our kitchen floor (based on several other negative reviews this leaking is not an uncommon occurrence).A few months into owning the machine, after our 3rd service call, we contacted Whirlpool, Customer Service and asked for the machine to be replaced. They refused to replace the machine but extended our warranty free of charge- better than nothing but not a cure to the problem and the only remedial action that Whirlpool was willing to offer. We didnt understand at that point that the problem of faulty and defective Whirlpool products was probably so huge that Whirlpool could not afford to provide a reasonable solution to their customers; leaving many, as witnessed on various product review sites, to bear the extreme frustration and associated expenses borne from the incurred failures. Unfortunately, here we are once again, requesting our 7th service call in less than 18 months, and asking once again for a replacement.The Whirlpool response this time (CSR was not allowed to let us speak to her Supervisor in spite of trying to negotiate that for several minutes) was that they would not replace the defective machine but would sell us a new $850 machine for $250 and would dispose of the faulty machine for an additional $25. Whirlpool would not however pay for the uninstall of the faulty unit nor the install of the new unit (about $350) which would have to come out of our pocket. We won’t be spending the additional $600 to fix this problem as proposed by Whirlpool; we won’t be installing another Maytag product in our home. We were advised that we could fill out a form if we wanted, to try and claim for the damages which the dishwasher caused to our kitchen floor. The form was never emailed as agreed and now we are just really tired of the whole experience so will simply put this all behind us.Our Whirlpool experience has been extremely stressful and quite expensive. It is clear to us that if an appliance which is averaging a serious failure every 3 months since the first day of installation, does not in the opinion of Whirlpool warrant a full and prompt replacement, or even the direct telephone attention of a Customer Service Supervisor, that the Whirlpool quality standard must be so low, the failure frequencies so high, that the number of similar failures prohibits any commercial viability to manage the problems in a reputable manner. Whirlpool clearly has some very large problems. It would not have been easy to destroy the once highly respected Maytag name. Such degradation could only take place as a result of continuous and ongoing Whirlpool quality degradation. We will no longer be their ‘crash test dummies’ but I do hope for the sake of Whirlpool (apparently North American made) that they take ownership of their poor quality condition, realign and spend the next few years becoming the company that we all once knew and respected.

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

I have always stored clean dishtowels and oven mitts in the storage drawer of my ovens (for over 50 years). I bought a new Maytag (2 days old) and was cooking in the oven tonight. I opened the drawer to get a mitt and it was on fire!! I am shocked. How dangerous is that! I looked over the manual and there is nothing that says towels cannot be stored in the drawer. It was literally on fire. I emptied the contents of the drawer into the sink. Has anyone else had this problem?

We are on our 2nd Maytag refrigerator in 6 years and both units have failed. Maytag will not stand behind their product and the service company declined to come out to look at the unit because we were upset and contacting the BBB. So we have spent thousands on 2 refrigerator units that have lasted 2.5 to 3 years a piece. If I could give no stars I would and I would advise to look at other companies and models.

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

This washer is garbage. Control panel went out twice in less than a year

Dont buy their washers. Plain and simple. Will never ever buy Maytag again. This washing machine is garbage and I paid a lot of money for it. 3 months out and it had to have the entire circuit board replaced. I was assured that this was the issue. It has never cleaned our clothing, in fact, they come out twice as dirty and with soap. Weve used the Affresh, weve put as little as 1 tablespoon of detergent, weve triple washed several loads and still ended up having to wash them by hand in the tub. Changing the circuit board did nothing. Weve tried setting it to max fill (which it does) and everything still comes out the same. Its not the water, its not the water hook ups (previous washer worked great but was old, should have kept it). This is the worse product that Ive spent almost a thousand dollars on. Its a paperweight. On top of this, it twists your clothes into a mass. I expect companies to be honest about their products and provide what I paid for. How many times does this washer have to be fixed before you will call it a bad design? Im having to literally do all my laundry by hand for the last 8 months. I want my money back so I can buy a good quality product that works. I could have bought a $300.00 washer that would have done better then this. You want more proof, go read their Facebook replies to all their posts. Its all complaints about their washing machines. It would be nice for once to see a company fess up and say they made a design error. But that wont happen. Their money is more important.

1. can not get enough water in the Maytag machine to cover the clothes. 2. All of the clothes come out twisted. 3. After watching the machine wash the clothes I notice that agitator did not move all of the clothes down into the water, and that was probably because there was not enough water in the tub. 4. The machine gets out of balance easily and at that time the machine door is locked and you need to push the pause button and wait for it to unlock the door. 5. Its louder than my old Kenmore washer that we have had for 15 years.6. The Maytag dryer does not dry as fast as my old Kenmore dryer that we have had for 15 years.Bottom line is I would not buy another Maytag product. Do your homework.

I bought a Maytag Bravos washer in March 2015. Over the summer I had two items, both cotton t-shirts come out of the washer badly stretched and torn. Other items have come out badly stretched, but not destroyed. After the second shirt was destroyed, I called Maytag (Sept. 2015). A young man was sent over. He ran the diagnostic, finding nothing wrong. He did not check the agitator. He reported back that it must be the way I loaded the machine. I use the Normal and Active Wear settings, leaving the center clear. My loads are very small. Under these conditions items should not get caught. Maytag stands by their claim that it is my fault. I only figured out what was actually happening when I saw an item caught.

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

We have owned a number of dishwashers, some cost a great deal and some were inexpensive. Our current dishwasher is a Maytag and it has proven itself to be the best dishwasher we have ever owned, not only is it quiet, it cost less to operate and cleans all dishes and utensils excellently.

Less than 2 yrs old and starts giving UL error on spin cycle. I try replacing the springs. No relief. Notice dark brown fluid under dryer. Thing sound like a plane taking off. A little more research and Im thinking its the bearings. Looks like an expensive repair, now I have to decide whether to cut my losses. Seriously? The reviews on here are just horrible, not like this was an dl hell machine.

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

We bought a new Maytag electric range from a local dealer three years ago. The oven element quit working, which shorted out the motherboard that controls the entire range. The cost of repair was $500 for the element, motherboard and installation. We have owned other brands that lasted 20 years and worked fine with no repairs. My folks have used Maytag for over 50 years with no problems. Who and where is this junk manufactured now? China? I will never buy another Maytag product!

Purchased new washer mid-February from Maytag dealer. He said machine has few problems and it was a good machine. 3 and one half months later, the machine is dead. No lights on display but power at plug. Repairman comes at appointed time and says it needs a new circuit board. Within a week, the part arrives and an appointment is made to install the new board and still have the same problem. Have to order a new console panel. 3 and a half weeks later, the part comes in. I have a job which I used the money to buy this machine and now the service advisor wants me to take off work so they can try to fix this machine. He told me I cannot return the machine. Whirlpool Canada LP Customer Assistance said they could not do anything. When I asked to talk to her boss, she put me on hold. She came back and said they would give me 6 months extended factory warranty and she would email this which I have not received. Work schedules will dictate when the next appointment will be made.

We bought top load washer model # MVWC425BW1 at Lowes brand new 9/22/14 for $493.93. On 11/23/2017 it stopped working and would not even come on after lid locked. Found out it needed new parts that would cost us over $300 to fix and we could buy another new washer for $400. We are very disappointed that this washer with only two people only worked three years when we thought we had bought a reliable product that would last. Sent several messages in November but no response till today 12/13/17 after filing. BBB complaint filed and they decline to do anything. So this company just wants to sell products but has no customer service. They only give a year warranty. Of course if the product is not going to last they want you to buy more.

Just had the repairman here. This machine is computerized so it won’t last. It does not have a setting that lets me do any load of laundry the way I need to do it. I have to use heavy duty to do a load and then it takes 2 hours. When I want to do a load of sweaters on delicate it will not put near enough water in the machine to wash them. The normal cycle does not add enough water to wash, let alone rinse the clothes. I can’t choose the size of the load based on how much I need to wash so I have to do more loads at 2 hours each or do everything on bulky. Whoever came up with all this needs to be fired. I am extremely unhappy with this machine and I have loved Maytag for years. No more.

The control panel of our Maytag dishwasher stopped working when it was approximately 14 months old. We repaired it ourselves by following a reset directions we found online (push rinse button 5 times and then the cancel button twice). Also we cut the power to reset. Im not sure which of those two tasks reset it, but it worked until last week - now 28 months old. We are not able to reset the panel using any information that we can find. In trying to find repair options, we discover that there are a lot of complaints about the Maytag dishwashers control panels not working within just a couple of years. In speaking with Maytag, they tell me theres a class action law suit for this problem - meaning they do realize there is an obvious problem with their control panels, but are not acknowledging they have any responsibility to repair it. The law suit only covers the cost of the part but not the labor. The labor can cost between $100 - at the lowest - and up. Our Maytag dishwasher model # is MDB8949SAM1. Also noteworthy, our Maytag clothes washer gave out at less than 5 years. Maytag is no longer the company we all thought they were. Additionally, their faulty machines are costing their customers a lot of extra money. Not exactly what I would call a company with good customer service or even any ethics. We will never buy Maytag again.

I agree with everyone one else and their experience with these washers. I took advantage of a credit for those replacing old washers with new HE washers. IF I COULD ONLY GET MY OLD WASHER BACK!!! Its only 2 years old and it sounds like - what others have said, like a B52 taking off (during the spin cycle). I dont have rust spots inside of the machine or out so Im not sure what the issue is but I really dont want to invest in a couple hundred of dollars to this thing. It stinks, doesnt clean well and now this! VERY disappointed...VERY. As a single mom, the thought of finding money to replace something that is new just disgusts me! Nothing like the old washers that last for 18+ years. Nice Maytag I will never purchase another product of yours and will spread the word!

I bought this washer brand new in 2011 for $650. I had bought a Maytag washer before in 1967 and it was still running in 1995 when I gave it away. Considering my first Maytag lasted me nearly 30 years (Last I heard the machine was still running in 2005), I never thought my new Maytag would give me any problems, until it was at least 10 years old. (I did know Maytag had been bought by Whirlpool but didnt expect any difference in quality). Boy, was I wrong! After using it for a month the machine broke down and it had to have the clutch and gear box replaced. Last week July 2016 the machine broke down again. It was the internal computer (referred to as the electric control unit) a printed circuit board that retails for approximately $300 (A ridiculous price given that much more complicated laptop and tablet computers today can be brought for $100, the circuit board should retail for no more than $40).With labor the repair bill came to $550, which was nearly as much as a new machine and did not justify the cost. Supposedly the electric control is susceptible to current surges and power outages. Given that this is the case, it makes no sense whatsoever that a machine billed as eco-friendly would carry a part that will doom it to the junk pile because of a power surge or outage and does not carry a surge protector. After learning of my experience Maytag called me the next day and offered to sell me a new Maytag at a discount price, which of course I flat-out refused.I would never ever again own a Maytag appliance or one made by its new owner (as of 2005) Whirlpool. With such susceptible electric units these appliances will sooner or later result in electric fires that will end the life of its owners. The US govt needs to protect US citizens from these predatory companies that make over-prized, throwaway products labeled as eco-friendly that are potentially dangerous. My advice for anyone that is thinking of buying a Whirlpool or Maytag washer dont do it. For those that already own these machines do not run them without a heavy duty surge protectors. It is not worth your life.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

We purchased a $945 Maytag 6.4 Cu. ft. self-cleaning freestanding electric convection range which was part of the stainless-steel package for $3600 + a $600-dollar 5 warranty. I did the research and found a solid 4.0 rating, so I went for it. Now I wish I never wasted my money and time. My 5-year warranty for all 4 appliances expired on 8/17 and now everything starts failing, how convenient. The oven will not heat past 340-350 degrees which won’t work with 90% of the stuff I bake. I called Maytag to see if it can be fixed and was quoted $400 for the issue but nothing else. I can pick up a new stainless-steel oven with the save features on a holiday sale for $500. Don’t waste your money on warranties!

On my 3rd circuit board for a MDB7749SBMO MODEL dish washer. The people at Maytag are people that wont even talk to you about it. How many people have to complain before theres a recall on a faulty ribbon cable.

I am so sorry to see so many people having the same problem. Maytag Dishwasher Model #MDB7749AWM2 purchased 12-10-11. Control Panel needs replaced (260.00...service call, part and labor). Writing this as Ive spent the last 20 mins on hold with Maytag. Im demanding them to make this right. Ive been told by Trisha at Maytag not to believe all these post as people tend to exaggerate the problems. Anybody have info on class action lawsuit? ?

Well, Im confused and nervous! Ive read the reviews and I LOVE my Bravos washer - cleans unbelievable, its quiet, no rattling of pipes. My daughter was highly impressed when she was visiting with her daughters. She told me my washer got stains out of her kids clothes that her washer could not! Im confused because of the number of bad reviews for this washer - maybe they changed the washer? Mine is about 3 years old and I am SO happy with it! No agitator, but cleans so well. Terrified if it dies on me, I wont be able to replace it.

Bought Maytag Bravos from Home Depot in Dec 2010. Wife didnt like the way it cleaned clothes right from the start. It wouldnt get clothes as clean as her 20+ year old washer. 2 1/2 years later and her $900 washing machine needs $600 in repairs. My wife will finally be happy with the way her washing machine cleans again because we are purchasing a new one this week, and it wont be a Maytag.

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

My Maytag washer and dryer (5000 Series) is about 2 years old. Just as soon as the warranty ran out, I started getting F35 and suds error messages. Information found on the internet tells me that many Maytag customers have experienced the same problem. Whats up with this Maytag? Since many of your customers have experienced the same problems, are you willing to meet the consumer in the middle by repairing the product at no cost or are you building the appliances to last as long as the warranty?

The Maytag Washer and Dryer we bought new and they have been great. The dryer was bought in 1972 and still works well. The washer was bought in 1997 and still does a good job. We are satisfied with the long time these 2 appliances have lasted. Do any appliances manufactured today last that long?

I have a Maytag side by side. In the first year, the ice maker failed and I had to replace it (in warranty/no charge). In the fifth year, the compressor failed (no warranty) and it hasnt been replaced. Since then, I have been looking at reviews and warranties of new refrigerators. The warranties (unless you want to pay $3,000+) are all one year limited. The reviews are scathing and it doesnt matter what brand. My question is, why dont you/we all get together and file a class action suit and demand millions in damages? Complaining wont get you anywhere with these people; however, hitting them in the pocket book will make them pay attention, especially if the penalty is severe enough.

Water level is totally inaccurate, if you do get enough water in it, it will not spin clothes dry. This is the worst purchase I have bought in my entire life. This washing machine fails in every aspect period!! AND the matching dryer is a waste of space as well, clothes come out damp regardless of setting or time period. When I was younger, Maytag meant something, not anymore! I have searched to see if there are replacement sensors, or upgraded components to make these machines work properly, that I would even be willing to pay for myself and get them installed to make them functional, but NO they dont even offer that... we are just stuck with them. My water bill is higher and my electric bill is higher too! From these machines. I wouldnt even sell them used to another person. I wouldnt want them to inherit these problems, but as soon as I can save up enough money {being disabled} I will get these hauled off and buy a set of Speed Queen machines. My wife and I are so repeatedly disgusted!! I wish I had the receipt so I could post it for more proof.

I have had my washer and dryer for 14 months and from day one, my washer eats holes in my clothes. It is always the bottom center front of my shirts. I complained about this and was told it was my clothes. They were either old, or the type of fabric, or too much bleach, etc. etc. Everything was wrong with myclothes except the washer. I purchased a new shirt and washed it without ever had worn it, and when I took it out of the washer, it has holes in the front. NOW YOU TELL ME that is the shirt and not the washer. I have used Maytag for the past 40 years and I never had any problems with the old Maytag washers. This new Bravos is a piece of junk and I am sorry I ever purchased it. I will never buy another Maytag product.

I also purchased a Maytag refrigerator model #MBR1953YES3 at Home Depot less than 2 yrs. ago. A year had not passed and I noticed the freezer starting to freeze up. Water started to leak from the bottom freezer. My husband had to break chunks of ice that clogged the drain but still, it continues to freeze. We hired a certified technician to clean the drain but a few days later, a puddle of water appeared all over our kitchen. Now we have a towel to stop the water from coming under the refrigerator. I thought when I was buying a Maytag, I was buying the best. I now know that, it was the biggest mistake. I will think twice before ever considering buying a Maytag again.

Washer Bravo MVWX655DW0 - Maytag has shipped the wrong part twice, sent me the right part which is faulty and the 4th one arrived today. I have not had a washer since 9-16 October 9, 2017. I am writing to tell you about my experience that Ive had with Maytag over the last 30 days. I have owned several Maytag and Amana appliances in the past; along with owning several currently. Over the years, weve had a wonderful experience owning these appliances however the last 30 days is one that has been unbelievable. On September 18 on a Monday early in the morning I called Maytag service line. I spoke to a young lady who had difficulties finding me in the system and did not know how to make an appointment to have a Maytag repairman come to my house to look at my washer. I did not take down her name as I thought and trusted that the company was acting on my behalf and would take care of me.I spent several minutes explaining to her that I did not live in Indiana that I lived in Iowa and that I would need a repairman who is close to my hometown. She continued to give me phone numbers with area code 407 in Indiana and then kept repeating some type of a ZIP Code 49 something for Indiana. I explained to her four different times that the zip codes in Iowa start with a five and the area code would be a 515 number in the area she was looking at. She finally gave me two phone numbers, one that did not work. I asked for a repairperson out of Jefferson. She told me Cranston Repair and gave me the phone number. She told me to call him. I told her that I would go with the Cranston repair since Jefferson with my hometown and it was close to where I lived.I then asked her if she would make the appointment. She told me she didnt know how to make the appointment and she kept messing up with the system. Not sure if it was her first day or not but that was fine so I said “never mind I will set the appointment up myself. I then asked her to double-check to see if our new Maytag refrigerator that we just purchased was registered. She told me she did not see it but all I needed to do was call back the next day with the model and serial number and anybody I spoke to on the phone could go ahead and get that registered. I thought I had registered online; I only wanted to double-check but she didnt see it so I assumed I did something wrong and then would make the call back the next day.I called Cranston repair and scheduled an appointment with the repairperson for the next day Tuesday, September 19. Repairman came the next day on time, looked at the washer and found that the transmission had gone out. I had purchased the washer just shy of two years ago. The repairman said that he would have to order the part and would let me know how long it would take and would return to fix the washing machine. He called from my house and was told that the part was on backorder until October 5. After the repairman left the house I decided to call Maytag back and express my disappointment in the product as Maytag says they stand behind their products and the fact that it was not even two years old and that a transmission would go out. The individual I spoke to this time, Antcwaniqua? Not sure about spelling, listened to my story. She also told me the part the repairman ordered was not correct.I needed part W1 1132267. She said that was a substitute part for the correct part that I needed which was W11035204. I told her that the part number ending in 204 we were told was on backorder until October 5. She said no, the part may show that in the system for repairmen but Maytag can locate the part in a warehouse, it would be shipped in 3 to 5 days. I told her that he had called a place in Davenport, Iowa. What she would do because of all the issues I was having was she would go ahead and ship the part out to me at no cost in 3 to 5 days.I wasnt sure about that warehouse thing. It didnt sound convincing but at that point I had to go along with it. What was shipped out to me was the substitute part W1 113-2267. At this point she told me that I would have to pay to have the part put in; I agreed to that on I want a new washer or I want my washer repaired within 72 hours at no cost. I have not had a washer for 3 weeks plus. Repairman in coming Friday and I am not confident that the 4th gearcase part that came today will work either.

I would have given this washer/dryer a 0 star, but wasnt able to. Bought the pair and first thing, couldnt get enough water in the tub, clothes wallowing around for an hour in the few cups of dirty water that it allows. Cant even believe how terrible this combo washer and dryer is! Now I get to wash everything in this piece of ____ twice, thank you Maytag! Just took out a load and it is dingy and stinks, so now its wet, on the floor waiting its turn to go back for another wash (possibly even a third).If you want clean clothes, do NOT get this washer. Dryer has issues also. For whatever reason, the AF signal has been on for a couple of months. Turn it off and back on and its okay for a bit, then back on. Its the Air Filter. Its not plugged, so I dont know, I just keep using it with intervals of resetting it altogether. What a total waste of money. Am going to give it away for free as soon as I find a replacement! Save yourself a huge headache and look elsewhere than Maytag. Oh, and if Maytag happens to read my review, you can contact me for a refund any time, just respond to this post, you can even come pick it up and get it out of my home. Thanks a bunch!

I bought it from a local dealer so that I could get it serviced locally. I bought it in 2012 and paid $750 for it. I hate just about everything about this (and all modern) washing machines. The deal breaker is all these safety features that are really inconvenient and pointless. If I could have found a good used washing machine at least 10 years old, I would have bought it. This is a Maytag Centennial. I dont like the automatically locking door, the inability to choose the water level myself, and the requirement to use a particular kind of soap. Also, I hate the idea that I have to clean the washing machine from time to time. Whoever heard of that? But you have to do it otherwise your clothes will have a sour smell. These new washing machines are not an advance in technology. I may have to go back to using a wringer machine.

This was purchased 3/25/2010 with the Home Depot Service Contract thru 3/2015 . We have already had a service call in 2013. We were OK until January 2015. Now we join many other customers with the leaking defroster. We have taken all the steps of the other customers. We went and called for a service appointment. Weve spoken to Maytag Customer Service 800-253-1301. Ive asked if there was recall? NO! I asked if there was log made of my call, NO! Any work done had to with Maytag Authorized Repair Person. The Home Depot Contract use a Non-Authorized Service Person. Weve gone to Home Depot. We are in a catch 22! We have spent good money on this refrigerator. Out of sight, out of mind. We will go back to Home Depot Again!

I purchased a Maytag side-by-side, model MSD2656DEQ, in June 2000. First service call within a couple of months was for a very noisy ice dispenser, which the tech said was normal. Other than the noise, the dispenser has worked fine. Aug. 2005, the freezer frosted up and the tech replaced the defrost timer and defrost thermostat. May 2010, I had the same problem again and again these two parts were replaced. This morning, I found the food thawing in the freezer, 3 1/2 yrs since last repair. It is Sunday so will have to call tech tomorrow. Third repair in 13 years for a $1500 (2000 year dollars) Maytag. I have never had an appliance with so many problems and it was the most money I ever spent on an appliance. I am done buying Maytag products.

I have a 2-year-and-5-day-old frontloader washing machine. The bearing and axle broke. The repair is over $500.00. It appears to be a known problem, as Maytag knew exactly what was wrong from the description of the noise it makes. They knew all the parts that would be needed. They would send the parts but not help with the labor. Evidently, it is a two-person job requiring several hours. They are not consumer-friendly and do not seem to care that the company reputation is going bad fast.

Within 1 month Maytag sent 2 repairmen to repair my microwave. I paid $271.20 for the repair and part. The same 2 parts used the first 2 times were ordered again and I was told that Maytag could not get them again. The service and parts are supposed to be guaranteed for 3 months. Maytag refuses to refund me; offering me 15% off a new purchase. I would not buy from Maytag. They lost a customer.

Barbara ** purchased a Maytag Bravos X washer. The washer did not perform anywhere near the advertised and EXPECTED performance. A letter was written to the Maytag Customer Center on July 12, 2014 complaining about the washers inability to clean or rinse clothes effectively. As of this date we have had NO direct contact from Maytag. After reading many reviews and noting that I have seen over 700 people which had issues with this machine, I wish that I had never purchased from Maytag. I have had to purchase a new machine to replace this useless Maytag. When I ask a used appliance dealer if he would be interested in purchasing my Maytag Bravos, his reply was, I dont want any Maytag Bravos in my store.I have made an effort to obtain some type of satisfaction from Maytag, but to no avail. I would like 100% refund for this purchase. If Maytag does not meet the expectations of its customers, then I feel that a class action law suit should be started through consumer affairs. When you cant even get a used appliance dealer to purchase a used Maytag Bravos, then there is a real problem with the product. The purchase price was $616.55. A total waste!!

Purchased a Maytag - MDB7749AWM1 dishwasher in 2011 from Home Depot. The door seal has failed several times and been replaced by a serviceman. The warranty has since run out but the seal continues to fall out every time you run the dishwasher and open the door. Has anyone else had a similar problem? I have considered gluing the seal in place but cant find a glue that will handle the temperature. Im sure that Maytag will say they have never seen this problem before. Maytag is off my purchase list forever!!!

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in Nov 2013. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within first 13 month. Then another valve got stuck about a year ago and the third one got stuck today Nov 19. So far I spent $400.00, just for 2 of them and the last one has not being replaced yet. This is a safety issue, because it always happen when the stove is on and will not turn off. I need Maytag to replace my stove because I am afraid this will burn my house down. I bought Maytag because they always advertise as quality product, and now I have to live with the nightmare of burning my house down.

Upon remodeling our kitchen about 4 years ago, we decided to put in Maytag appliances, one of which was the dishwasher . On Nov.29th, our granddaughters were playing with our dog when they ran through the kitchen and the dog started to yelp and went down and started to bleed. As she went past the washer her leg was sliced open by the bottom of the washer door. As it turns out, the bottom of the Maytag dishwasher doors has a sharp cut edge with no covers at all along the entire bottom of the door. We have also read about two children who have had the same thing happen to them. This is a very serious problem that needs to be addressed as soon as possible. The first surgery as of now has been $3,600.00 because of cut tendons. It would be totally irresponsible not to warn all consumers of this extremely serious hazard considering most families let their small children play in the kitchen

This Maytag washer and dryer are far more superior than the units I had before. It is also made in USA which makes me feel like it will not fail me as soon as the others. The agitation when washing anything is something else I love. I will buy more Maytag in the future.

I bought a Maytag Bravo Series 300 washer and dryer for $2,000. The dryer is fine, so far, but the washer is dead. I have not received any answers from Maytag and the product is already outside of its warranty. I only had it for two years.

I have had a Maytag smoothtop stove for over 20 years. The only drawback has been when someone left an empty pan on a hot burner. Some of the pan melted to the top which could not be removed. I have to get special pans to conduct the heat, too. Overall, I love it. It has a self-cleaning oven, too, which is a bonus.

Purchased this machine to replace the recalled Samsung washer that was exploding. I should have kept my Samsung. I loved it and had no complaints, but since there were reports of it exploding I took the rebate and purchased the Maytag Bravo Nightmare. Everything you have read or will read here is true. I would spend hours, I mean hours trying to do a load of laundry. If the cycle would complete itself, the clothes would be soaking wet, and they never smelled clean. I would try rinsing again and the cycle would start out with 18 minutes and I would return to the machine 1 hour later and it would be still running water and still have 18 minutes or more left. I watched it complete the spin cycle and start the rinse cycle again. We had the service guy out several times - he would call the techs and they would test the machine and say nothing was wrong other than it was off balance. They said I was using the wrong detergent - when proving that I was using an HE detergent, they counseled me on how to lay the laundry into the machine, and said I was using too much laundry detergent. After babysitting this machine for more than a year, and being told by Lowes Customer Service that the techs say there is nothing wrong with the it, I was fed up. I called Lowes and told them to send their techs to my house to do the laundry. I threatened to call for service every week until my extended warranty was exhausted. They finally gave me a merchandise card valued worth the purchase of the machine. Now, I have the painful decision of deciding what to buy next - It wont be a Maytag!

Never liked this machine. No flexibility in settings, ruins clothes, noisy and often shuts down. But main concern in the fact the whole top is rusting by the bleach dispenser and it leaks from the top all over. It is only 3 or 4 years old. Can not believe an expensive product like this can be so bad.

My wife told me yesterday she was getting a f51 code... went on you tube and took the top off and the clothes holder out, found 1 quarter and 3 dimes... put it all back together... same thing... took the back off... hoses off, unplugged it and the allen that holds the motor had backed out... no more maytags for me... Tightened the allen, all is fine for now... my opinion, this should never ever happen... No lock washer anything engineering to prevent this from occurring... My grade: replace the engineer...

Our experience with our Maytag refrigerator has been anything but good! It has the model # and serial # of the ones that have been recalled, only we have just found out about this. We bought this new at Sears. Soon after, it started having troubles with the freezer, would freeze up and the whole thing would stop working. Over the years, we have had repair after repair, money after money. Just for the record, my husband and I about every two weeks spend about one hour defrosting this monster! It looks nice on the outside.

This review is for a Maytag dishwasher. I do not know the Make/Model. It did a very poor job of washing the dishes. It may have been the city water, but no matter what I put into the machine to keep the dishes from being cloudy it never worked. It became disabled about a year after we moved in, and it was only about 6 years old. However, there were two families before me that used it and I have no idea how they used it. It was the first and last Maytag dishwasher I will ever use.

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

Similar to dozens of others, we purchased a Maytag dishwasher from Home Depot in March 2011. Recently, it stopped working, dead - no lights, no action. Called Maytag and they referred me to a Maytag Repairman: Coastline Appliance Service of Huntington Beach, CA. The serviceman came out and spent 20 minutes, checked the door switch for continuity, and declared the control panel bad. How do you know its the control panel, I asked. Its my gut feel, based on experience, he said! He charged me $129 for the visit and said a new control panel would cost $380! After reading other posts online, I can only conclude that a new control panel (if that is, indeed, the problem) will also go bad in the next year or two. So, like so many others, were off to buy a new dishwasher - and we will never buy a Maytag or Whirlpool appliance again.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

Bought a Maytag dishwasher 2011! Use it 2 weeks, digital board went down had it replaced! Now 2013, the board is down as well as the motor!! Can you imagine I use it once a day, at most 2 people in this house, and it completely breaks down! Thank goodness I have a Home Depot warranty. I would strongly advise against this product that I spent over $500 for 2 years ago!! How they could sell this dishwasher is a mystery.

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

Bravos XL washer - I agree with others, if I won the lottery, this would be on the street in two minutes. It is a complete waste of money. Nothing comes clean. Supposed to be water efficient, well not when you have to wash everything multiple times and I have to do them in such small loads to have any hope of anything getting clean. Some clothes just never look clean. I have the same issue with all my dark things coming out with white residue and yet I use liquid detergent. I follow all the instructions and do the monthly Affresh tablet (cash grab) and still nothing is ever clean. I am SO disappointed in this machine. I thought Maytag and Whirlpool were good brands but not anymore. I also get a constant HC error and there is nothing wrong with my water lines. Just so disappointing, save your money and frustration and buy something else!!

Both the washer/dryer are of the Bravos models and both perform amazingly well. It seems everything works so well, including the vents which are thorough and vent the machine well. Our laundry is always clean and the settings on both machines work very accurately! We believe our Maytags are simply the best operating machines weve ever owned!

I would highly recommend you do some research on the Maytag bravos XL machines and dryer.This thing is about as good as a piece of paperweight thrown in the fire for no good of nothing. Warranty ran out but it has a 10 year warranty so I don’t understand, bought one year ago been broke down three times in that time. Speed queen all the way.

I purchased a Maytag dryer (MDE2400AZW) 2 years ago, but have only been using it for the last year - and fairly infrequently, as this is a dryer that my guests use. I called Home Depot where I bought the dryer (along with the washer). I thought I had purchased an extra warranty, but turns out I only had it on the washer - what was I thinking. I wish I had read these reviews before I made my purchase. My local repair man charged me $192.00 for a new heater and his time. Theres a whole 90-day warranty on the new heater!! I sure hope this one lasts more than a year otherwise Ill be buying a new dryer and it wont be Maytag.

On August 25, 2011, we purchased a Maytag washing machine (Model Number MVVYC400XW2) at the Lowes Saugus, MA, store. Initially, we had no performance problems with it; however, on January 12, 2012, the washing machine wouldnt start. That day, I called Maytag for service on the machine, and it was fixed. Then on August 18, 2012, the same thing happened. A serviceman was called for the second time, and was repaired. Ironically, the Maytag 1- year warranty was expiring on August 24.Prior to the expiration of the Maytag warranty, I had been contacted by mail about an extended warranty plan, which I thought was being offered by Maytag, which it wasnt. The offer was being made by Federal Warranty Service Corporation. I purchased a 5-year extended warranty, expiring on August 25, 2017, the reason to have coverage for what seems to be a faulty machine. I would probably need it.Dealing with Federal Warranty has been nothing but grief. In 2012, the washing machine, had required 3 service calls, one with a Supervisor explaining my frustration with the number of service calls I have had made for the washing machine, but nothing has changed. Thus far in 2013, I have made two (2) additional calls for service on the same washing machine. Not only are there the numerous service calls made but the inconvenience of not having a washing machine, and the additional costs for outside laundering, during that time has to be taken into consideration. Additionally, my wife is 68 years old, and Im 71 (72 in August). Going up and down the stairs to the basement isnt something we should be doing, especially to find an inoperable washing machine.

Product: Maytag MFI2665XEM Ice2O 25.5. Bought this refrigerator on Feb. 2013 at Home Depot. Maytag cannot repair the heat exchanger as it is a discontinued model. Our only option: Purchase another comparable current model refrigerator with a full price of $2,199.00. It will be sold to us for a discount price of $1,308.00 with free delivery. NJ tax and installation not included. This is a two year old refrigerator with orig over $2000. We had requested for a repair since August 2015. We had spoiled food expenses and rented a temporary refrigerator. Numerous attempts to repair and order the parts to no avail. The excuse is either they ordered the wrong part and eventually was told its been discontinued. Our warranty was automatically canceled. We have spent numerous hours with the Maytag customer service and was given a promise to find the part overseas as well to get the appliance fixed. Finally, this morning of November 2, 2015, we were given the final Im sorry and this is all we can offer you, to buy another refrigerator from us. It appears that this is a defective model but we have not received any recall letters or warning about it. This needs to be addressed as this is an unacceptable practice and deceiving to the consumers, and certainly unfair for people like us who work very hard to pay for this appliances. We cannot afford another $1500 refrigerator. We are now stuck with this worthless, stainless steel junk in our kitchen.

My old Maytag is still working after 20 years but my husband surprised me with a new pair! Washers is just pure junk. Not enough water to hardly wet the clothes. They just rub together and get worn out looking, towels are rough and not soft but my biggest complaint is the AWFUL wrinkles! I have to iron everything! Only had it 3 days, called Menards and asked if we could return for an exchange or upgrade and they said no. If this is the best American Made has to offer, then I will look at the Samsung! Shame on you Maytag. Not one good review on here and you do nothing to restore confidence in American Made. I will spread the word - NEVER by a Maytag or an appliance from Menards. Neither one stands behind the piece of junk!

I purchased a Maytag dishwasher at Home Depot in October 2009. Recently, it made noises for a few months of laboring, and finally would not start.Maytag said it’s out of warranty and wanted $125 just to diagnose. Took it to my shop for $60 to diagnose and they found a faulty control panel.

BROKE AFTER 3 YRS. Purchase a new Maytag model: MVWC425BW1 top load washer and dryer after just 3yrs of use. It failed and to find out this is a common problem with these new open drum washers. The bearings go out. Be aware do not purchase them and they also do not wash your clothes good, clothes just stay in same position and you have to wash 2-3 extra washes. It was going to cost 350.00 plus to repair so I purchased Speed Queen that has good reviews. Tech said that top load open barrel washers have been a nightmare.

This is the WORST washing machine I have ever had. You cannot control how much water goes into the machine and the clothes being washed are not even covered by water. They stick out above the water at least a few inches!!! How can anything get clean if no water is touching it! I even add water into the machine at the beginning with jugs of water just to cover the clothes... the machine automatically gets rid of that extra water and when the wash cycle comes on again the clothes are not submerged! I paid A LOT of money for this awful machine and Maytag needs to do something about it! And, yes there is a sticky gummy substance on all the dark clothes! I even put clothes in the washer with a dirt spot on it purposely and the spot is always there when the wash is done. Nothing gets clean! DO NOT BUY this machine... you will be very sorry!!!

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

My daughter purchased this washer and matching dryer as a set from Lowes about 4 years ago. It was one of the few with an agitator and that is what she wanted. After using the washer for the first time she was very disappointed to find that the shortest cycle took over an hour and that the locking lid feature couldnt be bypassed. A few weeks ago the washer began gushing water onto the floor which flooded the basement below. She had purchased an extended warranty which was due to expire the following week.She called Lowes and scheduled a repairman. He finally came 2 weeks later and used the Internet to help him diagnose the problem!!! We could have done that. He decided that the control panel was only allowing the agitator to turn in one direction during the wash cycle. So essentially it was spinning a tub full of clothes and water causing lots of water to overflow the tub onto the floor. Needless-to-say he had to order a part and cant return for over 2 weeks to install it. IF this is even the problem! He also said he couldnt disable the locking lid feature! If my daughter had been able to open the lid when the problem started she would have known more about it.We are thankful her machine was under warranty but she will have been without a machine for almost 2 months when and if it is fixed. This is completely unsatisfactory for a gently used 4 year old washer. The dryer takes forever to dry also. If you are buying Maytag based on how long your grandmothers machine lasted, you will be disappointed! This washer caused so much damage we had to file a homeowners insurance claim!