We replaced a 20 year old Kenmore washer with this Centennial washer (MVWC360AW), and after 2 years we are looking for another washer. The machine will not complete the wash cycle, and when we called for service, the factory authorized service tech couldnt figure out what was wrong with it. After 2 service visits in a months time, I tried contacting the company directly with my story to see if they would help resolve the issue. I sent them a letter by mail as well as on their contact us link on the company website. They have not responded to me in any form. We will never purchase another Maytag product, and will tell everyone we can how terrible this machine is and how the company apparently doesnt even care.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

I built my home and bought all Maytag appliances. The freezer and fridge knock on wood have been repair free. Replaced control panel on stove for 400.00$. Washer after 2nd repair had to replace 600.00$. Dryer repaired once 95.00$. Replaced dishwasher with a new Maytag. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. This is the 4th repair. I have paid for 2 repairs out of warranty. 380.00$ the last repair. I did request some help from Maytag. They said no... My dealer did only charge me for the parts.

Bought this Maytag XL washer and dryer in September 2012. In January 2014, the washer stopped working. Service guy came out and said the electronics went out. Then in May 2014, the dryer died. The dryer door latch broke. Would not stay shut. 2 days later, the heating element went out. Again, the service man came out. This service man said that this model is subject to break downs. This Maytag is a piece of junk. I went out and bought a Whirlpool, which I had before. I would never buy a Maytag again. I paid over 2000.00 for this Maytag and it is the worst washer and dryer I have ever had. Apparently, the Maytag repairman needs to get his butt busy. I have the Maytag now on my sunporch, waiting for the junk man to come and get it.

I love my Maytag. It does a good job, however, it takes almost an hour to run one load. Also, if you have a heavy load, it doesn’t spin long enough so your clothes are dripping when you take them out.

I purchased a new gas range in Nov 2013, but didnt use it until April because I was remodeling a house I had just bought. When I used it to cook Easter dinner, my meal was cold; the oven heats, then shuts off. Maytag has sent service techs 3 times. They have replaced the control board and the DSI module and ordered another part, for which we have been waiting over 3 weeks. Now they tell me it will be here next week. Maytag obviously cannot fix the NEW range, but they refuse to replace it. They deem it to be repairable though they cannot repair it. Customer service claims to be sympathetic, but will do nothing except schedule another service call and offer to extend my service warranty. What good is a service warranty if they cant repair the appliance? If youre smart, youll steer clear of Maytag and Whirlpool appliances. They are total CRAP.

Purchased our Maytag Bravo Quiet Series 300 about 5 years ago and came to this site to read about other washing machine complaints because I am looking for a new washer. Was SHOCKED to hear so many similar complaints to mine (our local appliance store who sold us this unit, as well as services it, said this was unusual). Tiny holes in all our clothes! Black marks on clothes! Dirty clothes! LOUD & BUMPY washing - will sometimes walk itself around the laundry room, slamming into wash sink & dryer (there are dents to prove the violence). UL light that stops the machine & cant be resolved even after I untangle & lift water-soaked items. Finally started seeing black marks splattering out from under machine & was told the bearing is bad and the case (?) is leaking? ... Anyway, result to repair is MORE THAN ITS WORTH.Also have a 3 year old Maytag Quiet Series 300 DISHWASHER, that does not clean well, sometimes leaves half the dishes untouched (dry & dirty), grinds food waste & redistributes onto dishes before baking it on tight (requires soaking to loosen, then wash by hand) ... Oh, and is NOT quiet! I was told I probably use TOO MUCH SOAP. Seriously?!? My complaint is NOT soap residue ... It is D.I.R.T. How can you run a load and still have sauce & ketchup that dripped onto the inside of the door when loading the dishwasher STILL on the inside of the door??? Darn thing cant even clean itself!

In July 2001 my husband and I purchased a 6-year old home. We are still here. We have replaced the refrigerator, oven and microwave - all in stainless steel. I am still waiting for the Maytag dishwasher to wear out. It has never been repaired because it has never broken down. Cleans dishes and silverware great.

First off, the drum split apart on the dryer. The drum part was not in this country, so instead of going ahead and replacing the clothes dryer, they told me to hang the clothes outside for six weeks or whenever the part comes in. That was three months after owning the piece of junk. I was having a bad day already, so I basically completely lost it. Im surprised I didnt get arrested for that. I wont ever lose my temper like that again. The clothes always smell bad, and sometimes really bad. Now, I find out that both washer and dryer could cause a fire. They are sending us a couple of really cheap GFCIs to keep them from a liability issue. Maytag is the absolute worst!

The Maytag MGR5875QDW oven does not come up to temperature. It might start, but then it will give 2 dings and show a failure. I have called the 800 number in the manual. There’s no good help. I turned the power off and then on. It’s no help. This a pain in the rear end. That is a kind way of saying it. Home phone is **; cell phone number is **. Call me any time. Thank you. You do not want my wife to go on the internet!

Stove does not heat evenly in oven. Electric burner cannot be turned down to low or simmer, then it will not cook at all. Other burner turned down to low does not stop bubbling and stays at a high temp. There is no consistency. I am extremely disappointed and curse at this stove every day. Model #MER7664XB. Serial #R13316302.

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

I spent over $600 dollars on a Maytag Bravo 300 series. The washer has cost me over $300 to fix the latch and 2 months later, it will not spin. I would recommend to anyone not to buy a Maytag product! Garbage! I had a standard Kenmore washer that lasted over 10 years without a problem, paid $300 and still sold it for $100. The funny part is that I sold it to my brother who still uses it regularly and has not had any problems. So what is money worth? Your call.

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

I also purchased a Maytag refrigerator model #MBR1953YES3 at Home Depot less than 2 yrs. ago. A year had not passed and I noticed the freezer starting to freeze up. Water started to leak from the bottom freezer. My husband had to break chunks of ice that clogged the drain but still, it continues to freeze. We hired a certified technician to clean the drain but a few days later, a puddle of water appeared all over our kitchen. Now we have a towel to stop the water from coming under the refrigerator. I thought when I was buying a Maytag, I was buying the best. I now know that, it was the biggest mistake. I will think twice before ever considering buying a Maytag again.

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

Maytag 765 Washer - What a disappointment after having a Maytag set for 2 decades only to get a new one that isnt worth much quality wise. 2 new washers in 2 weeks due to a ratcheting noise that they both have. The solution??? Have a third service call only to hear, replace it (which we did) or replace the transmission. The 3rd call coming up will be the same. What good is a new transmission going to fix it when the last 2 machines had New transmissions. Quality??? I dont think so. Oh, I had to buy the second replacement in order to get credit for the first one. This was at Lowes. Is there even a quality washer out there anymore?

I bought a new Maytag dishwasher installed by East Town Appliance in Wautoma, Wisc. They installed it and ran a full wash cycle and it worked fine. After they were finished, I got all my glasses out and put in their dishwasher all excited to get them clean and sparkling. I started the dishwasher, put on a coat to check my birdfeeders on the deck where I was standing in front of the patio door. I heard water running suddenly. Turning around to see water gushing out of the bottom of the dishwasher. I called East Town back and had the installers return immediately. The pump was stuck open. I called Maytag about what happened and they said they wouldnt pay for the floor damage because it was already installed and to call my insurance company which I did. They went after Maytag and won but I had to pay $500 insurance deductible. I will NEVER buy anything by Maytag again.

Maytag Smoothtop Double Oven - Bought this stove 2 and 1/2 months ago and already buttons arent working. Very disappointed, not getting a Maytag again.

I bought a Maytag Bravo washer and dryer 18 months ago. While taking clothes out of my washer, I noticed that the plastic collar above the washtub was shredding around the edges. I called the manufacturer about it. Because it was more than 12 months old, they refused to do anything about it. I feel that shouldnt happen so soon after purchase. Im a single person and dont do that much laundry. The piece should be made of something more durable. I will never buy another Maytag product. Is there anything further I can do to pursue this?

I can’t seem to get any help with my dryer. I have replaced the drum 2 times and thermostat 3 times. Model number is mde9700ayw. Serial number is 13229569gp. I simply want a new dryer that works.

We purchased a Maytag dryer in Dec 2012 and several days ago the heating unit failed (mid April 2014). I did a quick search on this site and a few others where I saw numerous such issues with Maytag dryers. I realized that I was 4 months beyond the warranty period but took a shot at calling their customer service line to voice my displeasure only to get the company line that they could do nothing. My wife and I have been married 27 years this year and this was the 4th dryer we have purchased (1st and last Maytag) which obviously did not last like the other brands or like we expected. I definitely do not recommend this brand!

Oven was purchased and put in May 2014. I have not be able to use. The oven temperature is off. If the oven is used at 500 degrees the temperature is really 900. I thought I had a gas leak because I got a bad headache because of the smell. The gas co told me to get a repair person to look at it. Maytag has been horrible to deal with. I have taken 3 separate days off trying to get it fixed. The last Maytag repair man had the nerve to ask me where the gas line was. He shut the wrong off and had a gas leak in my house. I had to open all windows. He was supposed to come back the next day. He did not and I received no calls. I have paid for an oven that is dangerous that I cannot use. I feel Im being treated this way because I am an older woman. I will never buy another Maytag.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

I purchased the Maytag double-oven gas range, Model MGT8775XS, in 2013. The quality of this double-oven stove cannot be understated. Performance? Terrible. Reliability? Awful. My experience was shocking because when I was a kid, Maytag was the ideal for quality and reliability. Those days are over. When delivered in 2013, the ovens did not work. Heating went to 200 degrees and stopped. During the next three years, we had this Maytag stove repaired four times. The most recent repair was in October 2016. A new regulator and igniter cost us $360. Four weeks later you guessed it the ovens stopped working yet again. We sent the Maytag stove to the recycle dump. Its far more valuable as scrap metal.

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

Our washer ran great until last week. Had repairman in. User interface died after 18 months use. $250 for the part plus labor. This is a $1000 washer. Buyer beware. Maytag is just another name for any washer in the Whirlpool lineup. Uses the same parts. Has the same issues. Should have bought a Speed Queen.

I have owned this Maytag washer model # MVWC360AW0 since Dec/2013. I do not have a single complaint about this machine. It has worked flawlessly for 5 years and am very happy with it. I just follow common sense maintenance like cleaning it once every month (do a full cycle with just borax & baking soda 1/2 cup each) no clothes of course. Another thing I do is to leave it open after I am done washing so it dries completely before I close the lid. The washer looks and works like new, cant be happier...

I love my washer. I have had it for 13 yrs and has only needed repair once. My complaint is the gasket on the tub has black mold that grows on it. I have cleaned it with bleach, bathroom cleaner, alcohol, but it always comes back. What can I do to prevent illness from mold?

I have a Maytag refrigerator, Model #MBR 2256KES6, that is only 18 months old. It has totally stopped working. First, there was a large puddle of water on the kitchen floor and then a loud clicking noise in the middle of the night. It does not cool the fridge or the freezer. I cannot believe that a $1300 product is done working at 18 months. I cannot afford a new refrigerator. They should be arrested for selling such junk to the public.

I love my dishwasher. The only hold back is similar to what I hear about all others and that is that it takes a long time. I love that is it quiet, has lots of room and is easy to use.

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

Waste of $1700. Well all I can say is I wish I woulda read these reviews prior to buying but thought Maytag was a good brand. Boy was I wrong. Never again will I purchase Maytag products. I must say I haven’t had any issues with the dryer. Works great. The washer on the other hand is garbage!! It barely cleans the clothes. Some articles only get partially wet. Everything tangles together. The worst part is all my dark clothes ends up full of dust and lint. They look dirtier coming out than when they went in. Very disappointed. If you use deep load it takes about 1 1/2hrs to wash, definitely not energy efficient, and clothes still have lint on both cycles, and unfortunately most of our clothes need to be hung up, so dryer can’t pick up the lint. My old wash was way better. I shoulda went for same old style. Save you money and buy another brand.

My Maytag fridge was purchased on 2006 and since then have had multiple service repairs. Too much freezing, not cooling at all, fan replaced. Now freezer door not sealing.I tried a few days ago to get extension on warranty but was told it had expired so I could not renew. Why wasnt I told I needed to renew back in April before it expired? I believe they are not renewing because of the history of the appliance as it has too many repairs, it will not be cost effective for the company. We have also, in the last 10 years, purchased a washer and dryer and a large screen TV and all have the same problems. What are the chances of getting all lemon appliances? Obviously we are not shopping there any longer but many people are going to have to deal with same issues we did. All the while the company keeps making money!

This washer has a fault with certain types of blankets. Parts of these blankets come out shredded. We end up replacing these blankets. Other than this problem, the washer has worked fine.

We Purchased a Maytag gas oven/stove three years ago believing it to be the quality of the Maytag of yesteryear, Boy have we been disappointed! When Whirlpool Corp. bought out Maytag several years ago they continued using the Maytag name only.. The quality is now less than substandard, It is a cheaply built piece of crap.. We would sell it in a garage sale and replace it with a quality stove/oven but we dont want anyone else to have to deal with this piece of junk! It will soon go to the landfill!!!

On March 2011, I purchased a Maytag dishwasher model #MDB7749AWB1. The dishwasher worked excellent for 16 months. One morning, with dishes loaded and ready to go, the start button would not light up. The other buttons did light up but that did me no good, I need the start button. A few days later, none of the buttons would light up. I found a repair person who said it would cost over $200.00 to make repairs. I refuse to put another penny with no guarantee that this new part would work. I will never ever buy another Maytag appliance. The last inexpensive, unknown manufacturers dishwasher lasted me 13 years. Do not waste your money on this thing.

I bought a Maytag Bravos top loader in Oct 2011. About a yr after having it, it started having problems. At the end of the cycle, theres still water in the tub and clothes are soaked. A couple of months after that, it started completely skipping the wash cycle, so the clothes would just sit in dirty water and do nothing. I called the small appliance co. I bought it from and by the time I get done paying a house call and parts, I might as well buy another one. I called Maytag because it seems theyre all having the same problem and at some point youd think they would be responsible for their product. They couldnt care less and the options they offered me were a joke!! Please, whatever you do, DO NOT BUY A MAYTAG because you will be on your own if anything goes wrong (unless you want to pay them the price of a new washer!!).

I find this Maytag dishwasher just ok, nothing special. It doesnt seem to clean any better or worse than other dishwashers I have had or used in the past. It also seems to get really slimy under the inside of the door.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

The washer worked great for the first 6 months, then it didnt dissolve the soap, it wouldnt complete the cycle, and there is a loose bolt like sound when you spin the drum. The load level is not an issue. We have had the serviceman out four times, he has called the tech support each time and they cannot resolve the issue. Maytag said sorry! Unless it does it constantly then they cant help. The control panel has been replaced and the drum has been replaced. So we keep paying the water and sewer bill to rerun the load 1/2/3 times to get it to complete the cycle. This washer was purchased last May, 2011 and they say were stuck with it.

We bought a new Maytag top load washer March 2018. July of 2021 it starts making the worst racket Ive ever heard. I thought at first that there was a dog being killed by another animal. As I ran to the door I realized it was my washer. Long story short, repair guy said itd be cheaper to just buy a new washer. Maytag did nothing to help us resolve the issue of a 3 yr old machine totally useless. We bought this machine because we thought it would last for years. I mean their commercial shows the repair guys doing nothing because Maytags never need service. My new machine is not a Maytag. No more Maytags for me.

I have a 2-year-and-5-day-old frontloader washing machine. The bearing and axle broke. The repair is over $500.00. It appears to be a known problem, as Maytag knew exactly what was wrong from the description of the noise it makes. They knew all the parts that would be needed. They would send the parts but not help with the labor. Evidently, it is a two-person job requiring several hours. They are not consumer-friendly and do not seem to care that the company reputation is going bad fast.

In September 2008, I purchased a Maytag washing machine (Model MTW5700TQ0) that had a faulty transmission. The machine was immediately replaced. Three years later, the transmission is again faulty. Maytag has refused any responsibility for repair or replacement.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

Purchased a new side by side American made Maytag refrigerator (Model: MSD2559XVEB ) in August 2010 from Best Buy. Just returned from a 3 week vacation and the refrigerator died shortly after we left on trip ( 14 months post purchase date ). $700 worth of food ruined.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

We purchased Bravos series Maytag washer and dryer. These are a match pair, the top loader, extra large capacity, very top of the line, $$$$$. The washer has already been replaced after many repairs, but the replacement new Maytag leaves a powdered gray residue on all the clothes because of the small amount of water it puts in the washer tub. Even on the deep water cycle, if I put in a blanket it will come out of the washer half dry where water has never reached it. This washer is the worst I have ever seen and cost top dollar. Maytag says nothing wrong but when I show them the powdered residue on the clothes they refuse to answer. This is the worst engineered washer ever, tangles the clothes terribly, does not clean the clothes and usually forces you to wash them twice to removed the soap residue left on them. I have tried every soap on the market, stacked clothing as Maytag suggested, tried various tricks Maytag has suggested, but nothing stops the grey soap residue. This washer cost almost a $1,000 for just the washer, it is a disaster. I have asked Maytag to refund my money but they refuse. If anyone else has their washer - we need to join in a class action lawsuit to force Whirlpool, maker of Maytag to replace this piece of garbage!!!

Worst Washer ever...hated it from day one of receiving it (but couldnt return because moving into new place, took awhile to get it installed, and by then the 30 day return window had lapsed, so now stuck with this piece of garbage!). Is ALWAYS off balance whenever you wash anything of weight (i.e.: towels, sheets, blankets etc.). It takes me close to 2 hrs to get these items washed because I have to keep starting and stopping it to try to get it to spin dry because it ALWAYS throws the items so is off bal. and wont spin. Then when you hit pause, adj. bal., & start it again, it starts REWASHING the items (instead of continuing on from where you left off), and sometimes when it cant balance in the spinning cycle it just shuts down making you think the full cycle is complete, only to open up the lid to find your clothes all sopping wet. Also, NONE of the cycles will get any of my clothes clean...it just uses so little water your clothes come out feeling grungy and still dirty. I have had to resort to ONLY using the BULKY cycle because it is the ONLY cycle that will use a higher water level (mainly because bulky items like towels will absorb the water so it needs to add more). With this cycle at least my clothes dont FEEL dirty when they are done washing!There is no way of knowing how much time is left on any of the cycles, which is a real problem when you have to start and stop it, because you really have no idea how far back it goes to start itself up all over again. There is just no way to time it, because it keeps messing up where you have to keep stopping/starting it, and then you have no idea of time frame. Never saw a machine built so UNUSER friendly!I will NEVER buy a MAYTAG washer again, and NEVER will I buy a washer unless it HAS the center agitator, and a control for water level. These HE washers are the worst, and unfortunately they are now the only washers being made, but without water, clothes just DO NOT ever get clean anymore no matter which fancy and expensive detergent you use. HE washers are HORRIFIC. I may just buy an old style used washer with the agitator... at least I wont be wasting energy to only wind up with STILL dirty clothes when using HE washers! FINAL NOTE: AVOID Maytag HE Washers at ALL COST! You will be sorry if you decide to purchase one!

I bought a Maytag Refrigerator (Model No. MFT2672AEM10; Serial No. K31503192) on 05/13/2013 at LOWES. On 07/27/2013 my son got hospitalized due to some kind of infection. He had fever and diarrhea that didnt go away. We didnt know what caused it. When my wife was cleaning the refrigerator, she noticed that the ice bin container had a rusty screw and metal plate. Why is the ice bin screw/metal plate rusting? We informed Maytag about this issue and they replaced the ice bin. Now, the replacement ice bin is rusty again. I sent an e-mail to the Maytag Customer Service Manager on 04/20/2015 and was told that its no longer covered by the warranty. I informed the manager that this is a defective/flawed design/rusting part from the beginning and Maytag should have REDESIGNED it when I informed them first hand and not just replaced it with the same defective/flawed/rusting part. I told the manager that this is a safety concern and Maytag needs to do something about it. The Customer Service Manager I talked to didnt want to do anything about it.

I bought this MMV4205BAB microwave thinking Maytag was a good brand and I wanted an over the range type. Problems began when it would stop in the middle of a cooking cycle. I called the repairman as it was under warranty. It was decided by the repairman that the weight of thing was too great for its thin frame, not letting the door close correctly. I got a new one and it, from day one, would make a shorting sound every time anything was cooked, on the stove top, under it, while it was on. It finally just shorted out. I have a Maytag washer and dryer that are also junk. So, needless to say, Maytag, 3 strikes and youre out. I will never have another Maytag product and I let others know what a great product it is.

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

My Maytag refrigerator is less than 5 years old; the compressor went out (only warrantied for 1 year, 5 years used to be the minimum). I contacted the company who now owns Maytag, I believe Whirlpool. They told me they can fix it, no matter what the problem is, for $380.00. It turns out they sold me an extended warranty, but that was never explained in the conversation. Prior to contacting them, I had Sears out to fix it; they are the ones that told me it was the compressor. 1 week after buying the extended warranty, the repair company came out to fix it and found out the refrigerator was unplugged and informed me it needed to be plugged in for 24 hours in order for him to determine what was wrong with it. I scheduled an appointment 1 week later. When they came back, they said it was the compressor, and they needed to order the parts. 1 week later, they came back, and the compressor they came with did not work. 3 weeks now, no refrigerator. They said they would put a rush on the order, haha. Now, I have to wait another 8 days for them to come out to repair. 4 weeks without a refrigerator? I think there is some type of implied warranty when you purchase large appliances; these companies are getting away with murder. Are refrigerators now disposable commodities? Cheaper to buy new ones than repair the new ones? What will happen to our landfills?

MVWC200BW0 - Washer starts to fill and then drains before completing the fill cycle. Contacted Maytag through the live chat on their website (cant talk to a real person on phone). Since my one year warranty had been expired 12 days I was told to contact a certified repair person. They offered no help in solving my problem. Told nothing they could do, warranty had expired. Maytag will never get my business again. Now I know why the Maytag repairman is so lonely, people have quit buying Maytags.

I called Maytags customer service about an over the range microwave that was bought 2 years ago and barely used. The mechanism in the microwave on the latch for the door, clicked into the body of the unit and therefore the door does not register closed which doesnt allow it to come on. After explaining this issue to the customer service rep, she insisted that the only thing that Maytag would stand behind was the part if needed. A service call would be between $100 - $150. The microwave isnt even that old and why would Maytag not stand behind a like new unit? I bought 3 Maytag products and I am now regretting it. I had asked to speak to a supervisor and she just proceeded to repeat the same thing the sales rep did. They will only cover the cheap part if needed.What happened to Maytag being top of the line? Apparently they dont care about standing behind their products and would rather you buy an expensive extended warranty to cover their cheaply made appliance. I think they should be under review as a company. I would somewhat understand paying if my appliance was 5 to 10 years old. But its basically new. How is there no protection for customers when it comes to purchasing lemons from an appliance dealer? I will NEVER buy Maytag again and plan on selling my 2 other newly purchased appliances before they have issues. Maytags reviews on social media are terrible. All they offer are the words Im sorry and I understand your frustration. I assume thats just what they have written down in front of them to tell everyone who calls with issues. How do you not stand behind your products! I wish I could select no stars vs the 1.

After less than 3 years the interior lip of the machine is rusting. I found this when I was cleaning the interior of the machine because my white clothes were coming out with black soot on them. I can estimate that bleach was used in the dispenser 3-4 times tops over these 3 years. Very disappointed in the equipment. Ive submitted a complaint to Maytag with hopes of a favorable response. This should not be a warranty item...its defective design.

I purchased a white Maytag gas stove over 12 years ago. It has been great and never caused any problems. I live alone and rarely use the oven. However, I use the stovetop daily for cooking. With continual use, it has a lot of nicks and scratches. It also has stains inside the glass oven panel that I cant clean. The glass would have to be removed in order to clean inside. This is why I give a rating of 4 stars. If I used the oven more frequently, I would notice if it had any problems with the temperature, proper cooking, etc. and could give a more accurate rating. I have small toaster oven and therefore, I cook practically all of my meals in the toaster oven.

The ceramic coating on the interior of the oven cavity in the top oven, which I use the most (may actually happen to the lower oven in time) has cracked in the exact pattern of the hidden element. When I spoke to the salesperson at the store, he wasnt surprised and said that it will eventually bubble and rust!!! Called customer service and was informed they consider this an aesthetic issue with no fix!!! They will not offer any remedy or compensation. Are you kidding me!!!

I bought a Maytag dishwasher in Sept. 2013. This dishwasher looks great, but it leaves glasses stained with a cloudy haze. It also does NOT dry, even on jet steam dry mode. Bottom line, after a little research, I was the one who bought it, so I took accountability and just rolled with it. Well, the control panel stopped working this week (wont light up). I called maytag and the lady told me they would cover a service call and parts even though its not under warranty. When the service company called me, they said maytag will NOT cover cost, totally contradicting what the Maytag lady told me. After reading these other posts, I wish I would have visited this site before I bought this headache of a machine. I will never buy Maytag again!

Weve always bought Maytag, but this is our last time. The washer is just a piece of junk. It uses very little water and the agitator does not work. The clothes end up at the bottom in a ball. The water level is so low sometimes my clothes arent even wet. As I type this it has been stuck in the rinse cycle for 2 hours. It just keeps repeating. Maytag should have to replace everyone of the BRAVOS XL washers. I am no longer a loyal customer. I might as well go down to the river and beat my clothes on a rock. At least they would be cleaner. Shame on you Maytag!!!

I have a Maytag Bravos washer and on almost every other load, the dark clothes (mainly slacks) come out with white splotches on them and then I have to re-wash the pants and the splotches go away. What could be causing this? Im tired of washing clothes more than once. Its incredibly wasteful and bad for our environment. Thank you.

I purchased the Maytag dishwasher a little over two years ago (MDB6759AWQ0). This was the first Maytag product I bought and it is definitely the last one! It was more expensive, but because of Maytags commercials on what good products they had, I thought it would last longer and work better. Boy, was I wrong. When it was installed, it was loud. I brought this to the attention of Maytag. I was told there was nothing that they could do. Repair people were sent to my home several times to see if the noise could be fixed and unfortunately, it could not. This is the loudest dishwasher that I have ever had. I should have stayed with the same brand that was over 10 years old that died! Now the control panel blew out and will cost over $300 to have it fixed. After reviewing the numerous complaints that you have on your dishwasher with the control panels not working, I would think Maytag would be more financially responsible in helping the people that have your products that no longer work after being less than three years old. Just a heads up, Maytag, I will be replacing instead of fixing and not with another Maytag product!

My Maytag dishwasher Model No. MDB7759AWS1 caught on fire last night, inside the control panel on the top of the door. This was very alarming as it filled the house with smoke and caused some fire damage on the bottom of the countertop also. This could have easily caused a house fire and is very disturbing. When I called Maytag, they say this model is not recalled. In my opinion it needs to be. This is a huge accident waiting to happen in other peoples homes. Please beware. If the countertop would have caught on fire entirely, the house would have gone up in flames.

I purchased it 8 months ago. I have had problems with the machine leaving clothes soaked at the end of cycle. I have contacted Maytag (still under warranty) and they replaced the motor. The first load after repair still had the same problem. They said the check drain was not clogged. The snaked drain has no backups. After every wash, I have to reset the cycle to drain and spin. The machine spins for seconds and fills back up with water and doesnt spin again, but does drain. Clothes are sopping wet at the end of cycle. I contacted Maytag. They said I could be billed for customer education ($129) if they find no problem (threat). I want my money for purchase returned or at least 3/4ths. I expected my new machine to last years, not months.

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

After the 4th service call Maytag wanted a 2nd company to look at it. So on July 27th A&E out of Bristol, PA came out. He checked it out and said its not serviceable because theres a leak somewhere in the casing. Had to call KYW 3, On Your Side, they helped me get some progress. Jacqueline from corporate called and said they would replace it. It started on July 3 and now August 13 and still no fridge. Had my Maytag washer fixed, small problem. Parts came in a box marked Whirlpool for a Maytag washer from a Sears Warehouse. Plus the mechanic said my Maytag refrigerator is made by Amana. Buy American?

Our 26 month old Maytag fridge (Model MFF2258VEM8) was the french door freezer on bottom modern style fridge. The freezer stopped working. The repair shop took the fridge away and repaired a leak (quality control issue) and then the compressor failed in a test. They wanted $700 to make a repair that would have a 90 day warranty about 1/2 the cost of the fridge. Maytag was contacted at multiple levels and they would not even provide a free compressor or provide a substantial discount on a new fridge. What a way to treat a customer who once had all major Maytag appliances in our home. We decided to get a GE Profile fridge and are very happy with it. I will never buy another Maytag appliance. I dont think it is the great company it once was years ago.

Dissatisfied with the poor performance of the Deep Water cycle of Maytag Model #MVWX655DW0. Cycle produces low water thereby resulting in inadequate cleaning of clothes. Choosing another cycle to wash a particular load doesnt match what is recommended.

We too were having a water leak from the French door freezer and a sheet of ice under the freezer drawer. The repairman came and told us that it was a common problem with the French Door fridge and an easy fix. Maytag has a new P type defrost hose that doesnt freeze up. He changed the part, $149.75 bill, and no more problem. Should Maytag have let consumers know this was a part that was failing? Yes, definitely. But at least the fix was reasonably cheap.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

Our Maytag Bravos Quiet Series 300 is anything but quiet. Within two years of purchasing it, we now hear an F18 jet fighter taking off from our laundry room. Neighbors near and far come running to avoid getting injured when the spin cycle kicks into after burner. Seriously though, this looked to be a nice machine and operated flawlessly until a month ago when the spin cycle started sounding like a jet fighter taking off. I am handy and often fix appliances and things around the house. From reading reviews here on Consumer Affairs and other places, I am finding that the noise problems are more common than not. Investing $400+ into a replacement tub/bearing set would further support Whirlpool/Maytag and the sucking sound they make to get at my wallet. From what I have read, I am likely to have more problems after fixing this one (it will likely break again). I am going to quit while I am ahead and purchase a new washer. Whirlpool/Maytag will never see my business again. Its ludicrous to have an expensive appliance like a washer only last two years. BTW, I just spent $200 to replace the control panel on my 4-year old Maytag dishwasher. A cheap and horrible design. The part probably cost $10 to make. BOHICA. (bend over, here it comes again). FYI: Whirlpool owns and sells its products under several other appliance names. Names that include, Kenmore (yes, Sears), Maytag, KitchenAid, Jenn-Air, Amana, Gladiator GarageWorks, Inglis, Estate, Brastemp, Bauknecht and Consul (Wikipedia source). Like a Lotto Scratcher, peel the Whirlpool or Maytag name sticker off and underneath you will find the real name... CRAP! Its sad to think that you have to purchase products made in Korea to get quality. Very sad.

Maytag washer, top loader, Bravo series: We purchased Maytag washer and dryer 4 years ago. Last week, the washer started sounding like a 747 was landing in our laundry room. Maytag sent a service representative and informed us that the bearings were faulty and it would cost at least $800 to fix. It is appalling that a 4 year old appliance should fail like this. We will buy a different make and we will never buy any Maytag appliance again. This is such poor quality and worse service. Maytag would only offer a 30-40% off a washer, but only if we bought it directly from them. We can get a better offer from any local store. They also said we could get a discount on the part we need, but not the service. Do not, I repeat, do not buy Maytag anything. You will regret the purchase.

In late March or early April 2010, I purchased a Maytag Microwave from Sears in Ocean, New Jersey. The microwave was installed by Sears technicians on April 9, 2010. The total price for the microwave and installation was $356.53. I specifically purchased the Maytag brand because of Maytags longstanding reputation for quality products with long lifespans.On October 5, 2014, the microwave became inoperative and displayed a code of SE. On or about October 9, 2014, I contacted Maytag Customer Experience Center, via email, and advised them of this problem. I also wrote to Maytag explaining the situation. On October 15, 2014, I was advised via email that, as my warranty had expired, any repairs were my responsibility. I requested that my email be forwarded to Maytags CEO for consideration and review and was advised on October 20, 2014 that a Maytag supervisor would call me within two to three business days (of October 20th). After a follow up letter to the CEO, I was again advised on October 28, 2014, that the microwave was out of warranty and any repairs were my responsibility.I should add that I contacted Maytag Repair Service and was advised that the price of the repair far exceeded the price of the microwave. I feel that four years is not the expected lifespan of a microwave, especially a Maytag, and can only conclude that the Maytag microwave which I purchased was defective. I have purchased less expensive microwaves that have lasted for at least ten years. I got absolutely nowhere with Maytag personnel, found them to be curt and dismissive and would NOT purchase another Maytag product nor would I recommend them. Buyer beware - Maytag is not what it used to be! Very disappointing.

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

French door always has freezer closing problems. Whenever the freezer is not closed tight, the bottom will form ice block, and freezer doesnt close. I have extended warranty but the repair people do not give quick appointment. I sick of this product.

The Maytag Centennial (Model MVWC6ESWW1) washer was purchased in September 2009 and within 18 months no longer provided water at the temperature selected on the control panel. The problem started after we used a spin setting to remove water from a cycle that did not complete itself. Somehow selecting a spin cycle disturbed the water temperature control mechanism. We were advised by Sears to unplug and then reattach the electrical connection (similar to rebooting a computer), but this was not successful in water being delivered to the washer at the temperature indicated on the control panel. While there was minor damage to clothing and a waste of hot water before we realized what was happening, the real inconvenience is not being able to rely on the water temperature setting. Based upon reading comments on the internet (including Consumer Reports) concerning this washer, the public should be warned not to purchase this machine. Better still the machine needs to be recalled in order to protect the consumer.

They are coming for the 7th time to fix the ice maker. Three full replacements. The bottom of the freezer had a buildup of ice, another call to repair. I know where the Maytag repairman is, hes at my house.

I have had a Maytag smoothtop stove for over 20 years. The only drawback has been when someone left an empty pan on a hot burner. Some of the pan melted to the top which could not be removed. I have to get special pans to conduct the heat, too. Overall, I love it. It has a self-cleaning oven, too, which is a bonus.

Was so excited to get this machine so that I could wash larger loads, including blankets, but unfortunately the machine didnt really clean as expected. That was very frustrating, but even more upsetting was when it began to sound like a jet engine when in the spin cycle. In researching this online, we have discovered that it is probably the bearings. When we called for service from the local store where we purchased the washer and dryer, we were told that it will likely cost at least $600 to repair. We have looked online to see if it is something that we can do ourselves, but really dont want to attempt this as it will require some heavy lifting and a lot of time. I am amazed that a machine like this would fail in such a short period of time and would like to add my name to the list of people who will not buy Maytag again! If a class action suit is ever filed against Maytag for this poor excuse for a washer, count me in, but unfortunately I will probably need to buy a new one before much longer.

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

I had the old style machine and finally it gave out and I bought an LG HE Large capacity. It was a well I can print it here but kept the machine for 5 years and gave it away. I bought a new Bravo Maytag set 5.2 with the old style agitator thinking I was going to get a great machine and NO. These new machines do not use enough water in the load sensing and clothes on top never get in the water. They come out with soap stains even with a double rinse. And no I am not using too much soap! My old machine had small medium and large load settings plus you could add more water if needed. Way better machine.The techs are trained to tell you this is how the machines work and there is nothing wrong with them. Finally an honest tech told me they are having all sorts of complaints and problems. If all you wash is bedding and dress clothes you get by but if you really have soiled clothes you have to do a lot of prep and then stop in the middle of the wash cycle and rotate your clothes manually! Total BS for 8-900 dollar machines. Do yourself a favor and buy a front load. At least the clothes will get flopped in and out of the water and hopefully rotate so they actually get clean. That is what I am going to try before I go back to the old scrub board and tub!

July 2018 I bought a new Maytag electric washer and dryer. After one mo. the enamel inside the dryer started come off in sheets. It was replaced with 2019 model which after 3 mos. wont come on unless you unplug it and plug it back in after using it. I am now waiting for Maytag to send a repairman to come look at it. Steer clear of Maytag front load electric dryers.

DO NOT BUY THIS MAYTAG REFRIGERATOR. Purchased 9-30-19. Delivered 10-4-19. 12-9-19 - Not Cooling, Called Whirlpool on hold for exactly 1 hour. 12-11-19 - Repair service here - ordered new Control Panel. 12-17-19 - New Control Panel Replaced. 1-6-20 - Freezer is not freezing. Control Panel going up and down and blinking constantly. Called Whirlpool - on hold for exactly 1 hour. They called service repair. 1-8-20 - Service Repair here and ordered 2 thermostats: 1 for freezer and 1 for refrigerator. 1-15-20 - Service Repair here to install 2 thermostats - At this time I purchased the extended warranty for $119.30 for 3 years.3-1-21 - Control Panel completely went out again. I called Whirlpool - on hold exactly 1 hour before they answer phone. I am so pissed. They call Service Repair. 3-3-21 - Service Repair here. They order new Control Panel. States these panels are continuously going out and they are having to replace them everywhere. 3-12-21 - I called Service Repair since we havent heard anything. ETA on control panel from Whirlpool is not scheduled until 3-19. I am really pissed by now.In the meantime I have been on hold with Whirlpool for 47 minutes. At exactly 1 hour being on hold, they answer my call. Im told I have to wait. There is nothing they can do. I told her we were buying ice every other day at $10.07 for 2 20# bags and they wont replace money. Told me to throw my items away and they would replace all the food for $250.00 one time during the 3 year contract period. The service is Customer service on their contract is terrible. Waiting for parts is even worse. This is a piece of crap appliance and we will never buy another Maytag.

First front loader washer and love it. Saving on water, less tangling of clothes. So far they are quieter than others that I have had. The dryer is almost 10 years old and the washer less than a year. The machine I had previous to this was top loader that had to be replaced, would no longer spin.

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

My Maytag dishwasher (MDB7749AWM) stopped working at only 15 months. I had a technician check it and he said its the control panel not responding after he opened the door panel. Its when I searched online for replacement part I learned about the defective control panel. So I decided to forgo repair and bought a new dishwasher. I feel the manufacturer should be held responsible and called the number found on the internet, 858-646-8500, about a class action lawsuit filed in California federal court. The lawyer handling the case called me back that day explaining to me its a long road before the case qualifies for class lawsuit. Because I live in Texas, he will need someone to represent Texas plaintiffs in order to include Texas in the national settlement down the road. I said, I dont expect anything but would like to see a class action. Since I have no use of the defective dishwasher, he asked if I am willing to send the machine to him at his expense. I said yes. For all of you complaining about the defective dishwasher, I suggest you to call the number to join the lawsuit. Even though we may not see a penny for long, long time, its the only way to punish the deceptive business.

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

We purchased a Maytag Bravos X washer 2 years ago. Theres not enough water in there, and the clothes get so tangled that Ive had holes in them. Ive had technicians come out several times and they just say that its the water saving feature of the washer. I put it on the wrinkle control setting and the clothes come out ridiculously wrinkled. All of these problems are due to the water saving feature. I absolutely hate this washer and would never recommend it. I want my old washer back with the agitator and enough water in there to actually wash clothes.

The machine started having issues within a week of purchase. The current issue is, when running the clean cycle, the washer becomes stuck in a mode where it is constantly adding and duping water down the drain. First time it happened, I started the clean cycle before going to bed. In the morning the machine was still in the clean cycle. Running water in the tub and pumping back out down the drain. The water heater ran all night, as the washer was filling and draining the tub at the same time. Each time we attempt run the clean cycle, the washer locks up in this mode.This is the only issue I have had. Many people complain about wrinkled clothes and I agree. I take each garment out the washer and shake it out before putting it in the dryer, this makes a huge difference. Just remember, this is not your mothers washer. It does a great job at cleaning the clothes and saves many gallons of water a month.

MVWC565FWO Maytag Top Load - Bought a new washing machine less than six months ago... extremely noisy: Clank, Clank, Clank, Clank, etc. Reviews said it was just noisy, nothing wrong with it. Last week it would not spin the clothes dry. Now when it is plugged in, it does nothing but run the pump! No lights, no water. Also the deep wash was never deep at all - barely covered a modest load of laundry. Repair coming today. Wish I could return it.

Below is the message I submitted to Maytag on 5/6/2016 at 10:00 a.m. ET and just received an answer via phone call today 5/9/2016 at 3:30 p.m. ET that Maytag will be doing nothing. Also, my husband has still not received a call about the drum seal and when Maytag can come fix this part that broke in their machine only months after purchase. I will let you read my message to Maytag and you may decide if you would like to buy their dryer after reading what I sent and knowing they will be doing nothing. (Washer works just fine).If this message could be passed onto customer retention and/or management, I would greatly appreciate that action being taken. My husband, and I purchased a Maytag Washer and Dryer Set from Lowes in (Listed Location) on (Listed Date) (Model Number: MGDC555DW2 and Serial Number: **). The dryers drum seal has already gone bad on one side. We had a Maytag servicer come to our home on Monday, May 2, 2016 to confirm this and said he needed to order parts and we would hear back from him on my husbands cell number in a few days, which we still have not received contact. Additionally, due to the drum seal going bad, a whole load of laundry has extreme tears in the material to the point of being ruined. I have pictures of the clothes/sheets and drum seal, however there is not a location on this contact form to upload them. I have three work shirts, worth around $30.00 each and new bed sheets just bought in the amount of $77.39 which have full threads pulled through them due to the dryer going bad in only four and a half months of normal usage. I am writing to request compensation for my items that are now unwearable/unusable and would be glad to provide pictures and receipts for price of items. We of course have not used the dryer since, which has been a huge inconvenience, especially with no update in knowing when the dryer will be fixed and reusable. Please contact me back in regards to my request. Thank you.

Please do not buy a Maytag washer top loader. It does not get enough water and it does not clean your clothes. It is the noisiest cheapest made machine out there. If you have kids you really need to bypass this one. I have had this for 10 months and its only me. Please especially if you have children stay away from it. Im the most unhappiest camper Maytag ever had.

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

According to repairman this washer had a very common problem with what mine was doing. Water was gushing up out of the detergent, bleach, and softener dispensers and running out onto my floor. It was going to cost an arm and a leg to repair it. Mind you this washer isnt even 3 yrs old yet. Called the manufacturer and they basically told us that we should have purchased the extended warranty. We said if so many washers of that model had that problem they should have had a recall and fixed it for the customer. They said it wasnt a safety issue. I asked if falling on a floor covered with washer water and breaking a hip isnt considered a safety issue? No more Maytags for me.

I purchased a Maytag Top Loader Washer MVWX500XL last May 2011 from Home Depot to replaced our 15-year old GE washing machine. Two weeks ago, it started making horrible noise like a jet engine taking off during spin cycle. I called in the Maytag repairman and was told that the bearing is gone and it will cost $ 493.00 to repair it. He claims that the damage is caused by not using HE detergent exclusively and he refused to leave us a written estimate. We are only three adults in our household and we do our laundry once or twice a week. For this machine to be repaired only after 2 1/2 years of light service and for almost the same cost as a new one, I will never buy another Maytag/Whirlpool products ever again and I will encourage everyone the same.

I have a Maytag refrigerator that is 7 years old. It works fine except it needs a new freezer door gasket. In trying to get the part so it can be repaired I discovered that they had chosen to discontinue production of this part. I can no longer get it anywhere. They were the most unhelpful customer service I have ever worked with. They refused to try to find a part for another model that may work. They refused to offer a discount on a replacement product. They even refused to give me a phone number to talk to management. I had always been a loyal customer to their brand prior to this but I will never again purchase a Whirlpool or Maytag product. I dont expect not to have an issue but I do expect the ability to be supported in obtaining a commonly replaced part for a major appliance that is less than 10 years old.

Washer sounds like gearing is broken, is noisy during operation, various combinations of options dont work, appearance of only one agitation cycle combination on washer, just many settings but all with the same response; dryer does not timely dry clothes, all settings default to the same palpable heat temperature; clothes take much longer to dry in new dryer than they did in old Maytag. Newer Maytag set appears to be secondhand garbage sold as new by Menards. Company unresponsive to complaints.