My Bravo washer does NOT clean my clothes. I have tried many detergents. I have to pre-treat all spots with dish soap and run hot water over and then rub the spots out. This was the only recommendation given after consulting with Maytag. I have to pre-soak my clothes in a pail of water with detergent. The water is brown. My clothes are dingy, spotted and have bleach spots. I am very careful so this is not from pouring into the bleach dispenser. Maytag was the reason I purchased this washer. Never again.

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

Maytag Centennial Washer MVWC400XW2 - Bought this washer Fall 2011 -- first 6 months had to be serviced and now (February 2016) needs to be serviced again - has not cleaned my clothes for the last 3 months. Now, I have had to order a new washer - you can bet it wasnt a Maytag. My new washer will not be delivered for another 3 weeks. Past the part of not cleaning clothes, now it wont even empty the water, or pump out the water. It makes a horrible noise! Before it wouldnt use any water, now, it fills completely up. I do not know if it will make it through this current load much less another 3 weeks. Always bought Maytag before BUT WILL NOT AGAIN - after what I have been through with this washer!

We purchased our Maytag Neptune Washer and Dryer approximately 5 years ago. Over the past year or so, Ive noticed an odor coming from our washer and it’s becoming stronger. Water is staying in the drum and there is mold growing on the rubber seal when you open the door.

Eight years ago we bought all new top-of-the-line, stainless steel refrigerator, double oven range, dishwasher and microwave. All began malfunctioning within the first year: *The refrigerator began to make a loud rattle and the digital control pad needed to be replaced -twice within the first year. Within the next year the compressor had to be replace. *Dishwasher electronic control board was replaced twice, broke again and is still broken. *Microwave door handle broke off, and turntable motor broke.*Range burner ignition system only works on two burners and the shelf for the top oven does not fit -*Maytag refused to replace. Also, after using self-cleaning feature the lower oven still fills the room with smoke so it has been used very little. So, how much worse could it be? I had faith in Maytag-thats why we bought the brand.

We purchased a Maytag Bravo washing machine and dryer from Home Depot so needless to say, it was not an inexpensive purchase. I absolutely will NEVER purchase another Maytag ANYTHING! The washer will not spin and when it does, it sounds like it is coming through the washroom doors. The heating element has had to be replaced in the dryer and has always had a sour smell inside. I have nothing nice to say about these products and would absolutely NOT recommend them to even my worst enemy!

We bought the Bravo washer and dryer in 10/2009. Since then the dryer has never worked well. Weve had at least 8 service calls on same and the sensor doesnt work, i.e. says the clothes are dry when they arent and we always have to run them through at least two-timed cycles to make them completely dry. The washer is another nightmare. At least 8 service calls as well, and after one where the motor was replaced, it popped off and flooded my entire house. They laundry room is located on the second floor. I had to replace floors, walls, ceiling, light fixtures, etc. Insurance covered it but it never shouldve happened. Now the washer doesnt drain properly and the error code LD displays every load and we must manually drain it by either setting an extra drain cycle or take the entire machine apart and vacuum out the water. Each load takes twice the amount of time it should, if not more. But I guess its okay because the dryer takes just as long to dry a load of clothes. Something has to be done. Maytag is refusing to stand behind their products and it seems as though many of the complaints are for the same issues. Is there a lemon law for household appliances?

It is nice to know that there are other people out there that have the same problem with the Maytag washers cabinet inside and outside rusting. Our rusting is around the bleach area rim and on the outer seam of the washer. Our washer is now 4 years old. We started having the rusting problems in 2011. We called Maytag and of course. They are sorry for our problem but cant do anything about it. They made it sound like we were the only ones having this problem. We need to stand strong and continue to complain about this problem until Maytag takes responsibility for their poor quality washers. Anyone out there looking to purchase a washer. Do your homework. Buyer beware of Maytag washing machines!!!!

This dishwasher is extremely quiet and very attractive in the kitchen. Easy to use and does a great cleaning job. The price was also right. Would definitely buy again.

We purchased this brand new Maytag dishwasher (Model MDB7749) from Home Depot July 30, 2013. Now a little more than 18 months after purchase the control panel is out. Some lights blink, several go on at the same time. Tried resetting by removing then reinserting power plug (that worked once before, a couple of months ago,) but nothing works. Pretty much the same defect and problem I am seeing with other folks with these Maytag dishwashers. I saw online that a Sears outlet was selling these same model Maytag units for 48% off...Well, now I know why. My older Maytag appliances lasted many years. My Maytag washing machine was replaced two years ago, and it had lasted 14 years. I guess they simply do not build them like they used to. I should of just bought a cheaper model for 3-400 bucks, would of got the same use out of it. Does anybody know of a brand and model dishwasher today that is reasonably priced, dependable and has some longevity to it? I will call for service on this, but Im not spending hundreds of dollars on a defective engineering flaw, throwing good money after bad. Besides, the repair would probably only give me a 30-90 day warranty anyway. Learned my lesson. I will never buy another Maytag product again...Ever. Also I see now that they are part of Whirlpool, so they are out too. Anybody have any suggestions on a good replacement unit? Thanks...

Purchase in April 2010 on 12/31, motor and computer panel went out, not washing. I do not recommend this dishwasher cost to repair. Too expensive.

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

Purchased refrigerator with freezer on bottom. Purchased because made in America and husband raised in IA. Have had water leakage on floor every other day. Disconnected ice maker thinking that would help. NOT. Poor workmanship. You were good, WHAT happened?

Our Maytag Bravos Quiet Series 300 is anything but quiet. Within two years of purchasing it, we now hear an F18 jet fighter taking off from our laundry room. Neighbors near and far come running to avoid getting injured when the spin cycle kicks into after burner. Seriously though, this looked to be a nice machine and operated flawlessly until a month ago when the spin cycle started sounding like a jet fighter taking off. I am handy and often fix appliances and things around the house. From reading reviews here on Consumer Affairs and other places, I am finding that the noise problems are more common than not. Investing $400+ into a replacement tub/bearing set would further support Whirlpool/Maytag and the sucking sound they make to get at my wallet. From what I have read, I am likely to have more problems after fixing this one (it will likely break again). I am going to quit while I am ahead and purchase a new washer. Whirlpool/Maytag will never see my business again. Its ludicrous to have an expensive appliance like a washer only last two years. BTW, I just spent $200 to replace the control panel on my 4-year old Maytag dishwasher. A cheap and horrible design. The part probably cost $10 to make. BOHICA. (bend over, here it comes again). FYI: Whirlpool owns and sells its products under several other appliance names. Names that include, Kenmore (yes, Sears), Maytag, KitchenAid, Jenn-Air, Amana, Gladiator GarageWorks, Inglis, Estate, Brastemp, Bauknecht and Consul (Wikipedia source). Like a Lotto Scratcher, peel the Whirlpool or Maytag name sticker off and underneath you will find the real name... CRAP! Its sad to think that you have to purchase products made in Korea to get quality. Very sad.

I have had this refrigerator for a few years and never have had a problem. It keeps food uniformly cold, and is frost free. While appearance is attractive, it doesnt look like a $3,000 refrigerator. However, black pebbled-surface exterior is easy to clean and scratch-resistant. Plastic and glass interior fittings also have held up very well. I originally thought it would be too small because I was buying it to fit a certain space in the kitchen. But it has turned out to be just the right size because there is no wasted space inside. I bought this at Home Depot on sale for about $400.00 and it has turned out to be an excellent buy. Delivery was on time, efficient, and people were polite and helpful. Refrigerator was ready to be used about 15 minutes after delivery arrived. I have found Maytag appliances to be extremely reliable and made to last. They have never disappointed me. I will continue to buy them. I highly recommend it.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

The Maytag MFI2568AES refrigerators ice maker is broken and we cannot get a replacement unit. Whirlpool who now owns Maytag is of no assistance. The unit is two years old. I understand planned obsolescence but this is ridiculous.

Why are the clothes in my dryer getting stuck in Maytag Neptune? It seems there is a little opening around the rim of the barrel in the back of my dryer that drawstrings, zippers or similar small parts of the clothes can get stuck in. It twists the clothes around and is ruining clothes, also is making a thump-thump sound. Someone, please help!

The water got so bad it damaged my cabinets. I called Maytag, they admitted my model was sent out with no drain hose so this entire time my $2000 refrigerator had a missing part that they are very aware of. The part was free but I had to pay for the service. Its still leaking on the floor because the drip pan got fried from having no water in it to evaporate so it melted my drip pan, now it needs more service that I have to pay for. I have no faith that this will fix it. I will never buy Maytag again it feels like cheap plastic. I would love to start a claim against them for taking our money knowing the refrigerator has missing parts. Now Im part of the towel on the floor club group.

We purchased a Maytag Dishwasher in 2011. In 2014 I got no response from the control panel when trying to start the machine. Service came out and had to replace the control panel. The cost for that repair was $269.00. It has now just stopped working again. Same issue. After seeing all the posts, I realize that this is a prevalent issue and in some cases a safety concern. If Maytag knows about this issue with their control panels why have they not recalled or corrected these problems! Needless to say, I will never trust this company again!!! Model number MDB7749AWM2.

I bought this washer and dryer (Bravos MCT MA655LDY) after receiving several notices from Hydro that I was consuming more electricity than my neighbours! It was delivered March 31, 2018. On July 5th 2018 I tried to use the washer. It lasted exactly 3 months! I called The Brick who sent a technician out, he said the control had gone. Not sure what that is, but 3 months? This is absurd. I would like them to replace this washer.

I love my gas stove. Mine is a five burner in white. Easy to clean and an accurate baking oven. Keeping the burner area clean IS a constant chore with a white surface. It would be lovely if the company made liners to catch the mess, but alas, I make my own with aluminum foil. This is an excellent stove and I’d buy it again! No buyers remorse.

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

My five year old refrigerator freezer was leaking due to a corner filler part left in the the freezer compartment that lodged over the drain hole in the freezer. It cost me $232.90 to have a repair technician dig it out. MAYTAG accepts no responsibility for poor inspection, workmanship or quality control and they will not reimburse my fee.

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

I bought a Maytag Gas Range in January 2010. In January 2012, the wiring caught fire, and now, the oven is unusable. Maytag was not very helpful in our loss of money and product.

I feel its kind of cheap. The interior is all plastic which doesnt look shiny and clean as it use to be when it was new. Not efficient in cleaning. Can see still dirt spots in some of the washed dishes.

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

I have not found one feature that impresses me. Clothes do not always get clean (folds of debris). They do not spin dry enough. The cycle choices are ridiculously complicated. You cant add any clothes once the load has started. You have to wash the machine on a regular basis at about $3 per month. To get more water in the machine, you have to elect the Bulky cycle. Small amounts of bleach is so concentrated that clothing elastic is deteriorating and small holes may appear.The clothing most often comes out of the machine like twisted up tangled donuts. The cycles take about an hour and no longer match up to the dryer time - more trips up and down per load. The cycle guide is way too complicated - Normal Heavy, Heavy Duty Regular - whats the difference? Two service calls tell me there is nothing wrong with the machine - get used to it. I would much prefer the old agitator machine.

I bought a Maytag microwave in Feb of 16. Six months later, last August, it stopped working correctly (light doesnt come on, will not start, continually says open/close door to start). I have been trying for THREE MONTHS to have this fixed. Multiple calls to Maytag have resulted in nothing but empty promises. Calls to the store where we purchased it do no good - you have to call Maytag. We got 6 months use out of a Maytag microwave which we paid EXTRA to have installed. At this point I dont want it fixed. I want it replaced. The Maytag brand used to stand for durability and integrity; now it stands for badly made products and pathetic customer service. Look up my phone number on your computers, Maytag, and you will see all the efforts Ive made to get this fixed.

Control panel start button failed 55 weeks after purchase and installation. Model no. MDB4709PAW. Repair costs for labor and part totaled $298. I have since found out that Maytag dishwashers with this type of control panel are faulty and fail often within first 3 years. Purchased at Johnnies Appliance, Glendora on 6/14/14 NJ; ticket no. **.

Our Maytag Elite Series dryer is not under warranty but we have had nothing but issues with this dryer since we have had it. However, now I have holes in the heat intake at the back of the drum. This is so very dangerous and could cause a fire. I am certain this is a manufacturing flaw. How on earth does the inside of a dryer have parts that will not hold up to heat? At any rate, I want it fixed. The only way to fix it is to replace the drum. This has to be a flaw in design or manufacturing and this particular model should be recalled.

Dont buy this machine. Although it is an HE machine and supposed to save on water, it does not give enough water to at least cover the clothes. I had repair come in and they changed the computer but no improvement. The cycles determine the water amounts not the type of clothes you are washing. So if I only a few things I use cold water wash, if I have a half load I use deep water wash and have to add water to it. Its ridiculous. Do yourself a favor and get an LG. I wish I had.

Maytag Bravos XL MCT (Disposable). Model number MVWB835DW3 Top load washer. I’ve read many of the reviews on the site and feel your frustrations. Let me start by saying, at least you have a choice of products. I’m stationed in Okinawa Japan and have ONE place to buy my appliances and a choice of two machines. Both of them are garbage Maytag products. The first one (model noted above) died after 18 months. NOTHING they could do! The “technician” they sent didn’t have a clue. His answer was to replace the control board. Time to receive part? Up to 30 days. Really! My option? Buy the exact same product. I can’t even describe how screwed over I feel.

No matter what we we do we still have soap residue left on clothes, even when we do the 2nd rinse cycle (what a waste of water). We use the correct amount of HE detergent and we use the detergent dispenser but it doesnt helps. The machine just doesnt use enough water. We have removed items that still have DRY SPOTS on them when the cycle is done. Areas that have never gotten wet after a 45 minute cycle. Never once had this happen with an agitator machine. Would not buy this machine again. Model: C80441070. Serial #: MVWX655DW1.

I have always hated soft touch control panels so I purchased a Maytag Dishwasher with old style push buttons. IT DID NOT CLEAN THE DISHES, so Lowes took it back and I was convinced to UPGRADE to an MDB7749SBB0 and was told this machine was top of the line, although it was VERY temperamental from the start. I guess I should have done my homework. I see now several complaints about the control panels not working. I was told that MAYTAG was a very reputable company and that they stand behind their product. WRONG!. The company KNOWS these panels have problems and should replace them free of charge as it is obviously a defect. Nope, first they offer to send someone out (In a week) to repair it at $80 just to look at it and the panel is over $100 to replace, and when I complained they tried to sell me extra coverage for $250. REALLY? What is the purpose of purchasing a QUALITY dishwasher? I might as well purchase a cheap dishwasher and replace it when it breaks. I think you should be responsible for your product when you have several complaints on a specific part.

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!

This is my THIRD dishwasher, and by far the best. The Bosch machine I had before that was a catastrophe: mediocre cleaning, intense filter cleaning required - at least every two days - and, with a pretended noise level of 47 dB, MUCH noisier than the 50 dB announced by Maytag. Somebody is laughing at someone! To sum up: the Maytag MDB4949SHZ cleans dishes incredibly well, is very silent and requires no filter cleaning.

I purchased a refrigerator 9 years ago and the ice maker stopped working. When the repairman took it out there was plastic peeling from the ice mold. It cost $261.11 to have the ice maker replaced and the ice maker he replaced it with has the plastic on the ice mold. He said that GEs ice makers do not have the plastic coating but Maytags still do. I called Maytag and spoke to a supervisor and they said that there was nothing that they could do. I am filing this complaint because I feel that consumer need to be aware that they are ingesting plastic that is in their ice. I feel that Maytag should compensate me for the faulty part and also eliminate the plastic coating from their ice maker. This issue is impacting many other consumers and they need to issue a recall on the ice maker and replace it for free for other consumers.

I purchased our Maytag Dishwasher in 2014 (Model # MDB77495B) and after a little over a year, of course after the warranty had expired the panel started to act up. I did get it repaired costing over $300 for parts and service thinking all is well. The repairman that came out had to come out twice once to look at and then again to fix after the part came in. We had a conversation and he said that was common with this brand, the steam sometimes affects the panel. I spoke with Maytag about getting an extended warranty but after looking at the cost passed on it. Well now the panel is acting up again. If Maytag thinks I am going to have another repairman come out well think again. I will see how much the part cost and do it myself if it cheap enough, if not I guess Ill be back to washing dishes by hand for awhile. I bought this brand feeling that it was American made and the cost was on the expensive side that it would last. I am disappointed that this has happened again. For the money spent it should last at least 10 years. My old dishwasher that was given to me used lasted over 15 years with not one problem. Its a shame we cannot get good working appliances as we did back in the day.

We purchased an entire suite of Maytag kitchen appliances in September 2014 at a cost of $4300. Have had problems with every single item. The MMV5219DH microwave was the first issue. After a year it began to give us erroneous display messages when we tried to use it. We would input the number of minutes we wanted the food to cook, and wed get a message saying CHK TIME/OPEN DOOR. Repeated door closings, resets of the time, etc. did nothing. Sometimes if we hit cancel it would work - other times not. Wed push every button on the keyboard and eventually wed get it to work - perhaps 10 minutes later. When I called the appliance store (Vics Appliances in Saco Maine) I was told to unplug it for an hour. Okay, that corrected the issue - for a few days. When the problem continued, sometimes unplugging it had no effect - other times it did. Eventually we figured out if we didnt reset the clock time it would work most of the time (not 100%). The Maytag refrigerator began to malfunction at the same time (not keeping temp, and the ice in the icemaker melting and refreezing in a big lump that blocked the door water/ice dispenser) so we called Vics again and set up a service call. Serviceman reset the microwave to factory specs and we will see what happens. He also reset the fridge to different temps, and 2 days after his visit it has again melted the ice in the icemaker and formed a blob at the bottom. DO NOT BUY MAYTAG!!!

I purchased a washer/dryer, Maytag from Home Depot Nashville. It was delivered and set up. 02/24/17 the date of purchase, delivered 03/07/17. I have tried in every way to get the washer to wash properly, but to no avail. The water level doesnt cover the clothes, it takes 10 to 15 minutes for the wash to begin its cycle. It doesnt spin the clothes dry enough to put into the dryer. The washer makes all kinds of sounds thats drives you nuts while setting up to not wash your clothes clean. I have contacted Maytag on several occasion about this problem, they sent out someone to service the washer. Now, why would a brand new washer need servicing. Somethings wrong. It isnt functioning up to standards and they should give me another washer.Now on 05/18/17 the washer was serviced, I have called them again to do something about this piece of **. I was told that the only thing they could do is come service it again. Why, must this brand new washer be serviced every week. It doesnt make sense... I dont want this machine, I want my money back so I can purchase a machine that will wash my clothes properly. I purchased a secondhand washer and dryer from a used appliance store, it lasted my family 10 complete year. The only reason I dont have it now is because I wanted to upgrade, since I have never had a brand new set. What a disappointment. Everything that looks good from Maytag isnt good. I dont understand why they wont stand behind their product.Somethings got to be done about this. Maytag will not take my money 1,200 and force me to keep this malfunctioning piece of nothing. Im going to Youtube this product so the consumer can see how this product doesnt work properly, therefore they wont waste their hard earned money. I will be contacting the BBB Nashville, and wherever I need to. I will let the consumer know the make and model of this product and where it was purchased from. Maytag I want every penny back. And, should hold you responsible for ever time I have had to go to the wash house because my brand new set wont work, and your company wants to service it every time I try to wash. I purchased this appliance on the strength of the well known name, that was the wrong thing to do.

Our Maytag Dishwasher, Model MDB4949SDE2 was purchased May 14, 2016 at Home Depot for $470. It has performed perfectly until January 6, 2020, when a noise, loud enough to imitate grinding wheel, happened with every Start-Up attempt. An independent technician advised replacing the pump motor, thinking that perhaps some popcorn kernels had lodged in the system. (Kernels were cleaned out of the drain filter.)We operated the unit after he left, and the noise began to diminish, eventually disappearing altogether after several loads. Today, February 26, 2020, the same tech found that the large, upper impeller was clogged (not rinsing completely) with citrus seeds and VARIOUS METAL SHAVINGS & SMALL PIECES OF WHAT WOULD BE CHOPPER BLADES FROM THE INTERNAL GARBAGE DISPOSAL. After reading the Maytag Dishwasher problems experienced by others (with repeated control panel failure, burning wires, leaks, and house fires), I consider us lucky to have none of those. We will not run the unit at night, nor with an empty house. Next problem, we will buy a Chinese made dishwasher, like GE.

I wish I would have read reviews before I purchased this washer, but I was in a hurry to get a new machine. Maytag has a great reputation and we went on that!! My Bravos is 2 months old and we have been away for a month! What a disappointment so far. What Ive noticed is all my dark items have residue on them, and today some of my light clothes came out looking like there is grease on them. Im afraid its going to wreck more clothes! Does anyone know if theres been recalls on the Bravos XL washing machines?

I bought a Maytag refrigerator, model MBF2258XEW, March 2013. Bottom freezer, single door. The past 3 or 4 weeks I have been noticing water occasionally puddling on the floor at the freezer. The ice maker has never been hooked up, with no problem before now. I recently noticed that my wood floor is darkening in a spot that often gets wet. After reading some of these complaints it appears I am not alone experiencing water problems with something that is sold on its reputation for being trouble-free. I also see that I should expect to pay a few hundred dollars out of my pocket to fix the problem. Very disappointing.

We purchased our Maytag gas range in 2015. Within 6 months we noticed the clear coat and paint was defective, we called Sears, they allowed us another range top and replaced it but told us our warranty was up in a month and they would not replace another. The stove always looks dirty because the clear coat and paint have bubbled up and it is clearly a 100% manufacturing defect that should be recalled.

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

Like most people with this Bravos machine, I am 3 months out of warranty and the ball bearing is trash. When the wash goes into spin cycle, it makes a loud clicking noise and takes a few minutes to start spinning. I called service repair and he told me that it was the ball bearing and to talk with them as he has dealt with quite a few high end machines from Maytag that are breaking down after warranty. I should have realized there was a problem when we kept coming up with white spots on our clean laundry and would have to re-rinse clean clothes. This kind of defeats the water saver that is advertised with the machine.Do not buy this product. For a high end washer and dryer, there are many problems. Maybe that is why the Maytag guy is not shown sleeping in commercials any longer. Hes too busy fixing all these machines. Btw, they wont cover the part even though I offered to pay for the service. The best they can do is give me 25% off. Yippee! I cant wait for the other problems to hit me like everyone else.

A lot of the reviews contain complaints about the Bravos XL MCT top load washer. We purchased one in December, 2015, and so far have not had any problems. We had a 3 yr old Whirlpool side loading washer that we just gave away, as it never got enough water to even dampen a comforter or quilt. This machine works very well, in spite of lower level of water. I was pleasantly surprised when I could see the water level with the first load! The controls are not as intuitive as other machines; e.g. spin only requires you to select Rinse/Spin cycle, and THEN turn OFF extra rinse. Perhaps the proper way is to have a Spin-Only cycle, and then tell the user to click the extra rinse ON. We do probably 1 load a day. Water bill has not been significantly higher than when we had the Whirlpool that hardly used any water. Today, though, a heavy quilt (it WAS distributed evenly around the impeller) was put on Bedding so the water level would be a bit higher to ensure the entire quilt was wet. Fine so far. However, during the Spin Cycle, the unbalance became so violent that the washer stopped for a few seconds and then went BACK to the Rinse cycle. It did this several times before we realized that the time remaining had not gone down in over 30 minutes. My guess was that the sensor believed that maybe some additional water with another Rinse cycle MIGHT even out the load. It didnt. I finally stopped the machine, redistributed the quilt and then ran the Rinse/Spin cycle, choosing NOT to do the extra rinse. All came out fine. There was NOTHING in the manual indicating that this might be needed, except for the instructions to Spin only. If I have any other problems, I will send here.

Maytag French door model is four years old. Water accumulates on the freezer floor in small puddles. As I read other comments, this seems quite often the case. I should probably pull out the refrigerator to see if I have water leakage on my floor. From reading other reviews, it appears that Maytag does not stand behind the product. Am I forced to do the repairs myself, or am I forced to find a repair person and hope their fix eliminates the problem? Any advice would be helpful.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

I purchased this gas range from Home Depot in 2011. From the beginning I had problems with the cooking racks slipping off the oven wall. In some instances hot liquids poured on the oven floor. I had bought a service contract on this product and when I asked that this be repaired I was told that it was not covered as it was a design flaw. The condition has slowly worsened and now I cannot cook anything in the oven for fear of the racks falling down. This is a safety feature and the oven should be replaced my Maytag.

Purchased a supposedly top-of-the-line Maytag washer and dryer (9000 Series with Steam and MCT-Maytag Commercial Technology; Washer MHWE900VJ). Just under five years of use and the repairman quotes me just over $1000 parts and labor with the overwhelming majority of that quote being parts. No wonder the Maytag repairman is the loneliest guy in town - its not worth fixing your not-yet-5-year-old machine. It kills me that companies are allowed to advertise and promote the quality and reliability of their products and less than 5 years later, the machine is going to the dump, after having paid a premium for quality. This technology was supposedly comparable to what is used in a commercial setting - not very believable in my opinion. No more Maytag or Whirlpool for me.

We purchased all new Maytag appliances when we built our house. So far, the stove/oven has quit working and been repaired 3 times; its always the ignitor. The dishwasher has been fixed twice. The washer no longer spins out as it should. The refrigerator and dryer so far have run okay. I am definitely going to change brands with my new appliances. I will not purchase Maytag again. Its not what it used to be. I will do without oven this time, until I can buy a new one. Also, the dishwasher door has had problems from day 1, and now, it will not close at all. It seems like its off the hinge. Definitely, its not the Maytag of years ago.

The washer 4 years ago we had the control panel replaced at our expense. Now, control panel is going out again. Also this summer I took the dryer apart to snug up some screws that had come lose, that were scraping the inside as the dry ran. I own a range and a dishwasher Maytag brand but will not buy another Maytag unit, even if they are built by my union brothers and sisters.

Both the microwave and French door fridge handles are crap. The microwave has completely broken and the fridge is very loose and will soon break, Im sure. Both are less than 5 years old. I will never buy Maytag again.

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

I have had commercial front loading washers since they came out (first was a Whirlpool Duet); although I like the capacity they have for large quilts and sleeping bags, they just dont seem to clean as well as the agitate-in-tub style, and they can take a ridiculous amount of time for a cycle -- wheres the energy savings there that they advertise? Im going to go back to the agitate-in-tub of water style when a replacement is needed. A lot of hype and expense, and plenty of experience with these on my part, but Im going to grade them a C, at best, compared to the agitator style washing machines I use to own.

I bought a French door refrigerator on May 23, 2012. It is now July 9, 2014 and the repairman has told me the compressor is bad. Maytag will do nothing about it because it is out of the 1 year warranty. I am very disappointed because I thought I was buying a quality appliance. I will never purchase another Maytag appliance!

Maytag Model MDB7749SBW: Lights on control started flashing even when not it use, cycle lights varied, dishwasher would start on its own. Stopped at dealer and he said he never heard of problem. Checked online and found problem identified all over the internet. Called Maytag and they knew of problem and said they would send serviceman out to check. First trip free and parts would be free but I have to pay labor for second trip to repair. Dishwasher is just under 4 years old. Serial F31703877. Problem is corrosion on small flexible circuit at top of door. Same problem as others. Maytag states never been a recall!!! THIS CERTAINLY HAS THE POTENTIAL TO CAUSE A FIRE. Will never purchase another Maytag or Whirlpool appliance again. Poor quality and lies on the part of company and dealers as well.

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

Bought this Maytag Bravos Washer online from Lowe’s in the holiday season of December 2017 because my previous Maytag HE washer broke after 17 years. I have had nothing but issues with this washer right from the start. The clothes do not come clean as I find myself putting them through the wash cycle two or three times to have them washed and come somewhat clean. The clothes come out soaking wet that I have to put them through the rinse and spin cycle at least one or two more times. I called Lowe’s to complain about this washer and they said they only have a 30 day return policy and they would be happy to call for service for me. I told them it didn’t work from the start but they didn’t care. So now, sadly, I have a repairman coming this week to fix my new washer, And hopefully he can fix it that I can use it and it can properly wash clothes. I wish I would have her read the reviews on Consumer Affairs about this washer before purchasing this Maytag. Not happy with Maytag. I would have never bought it and bought a different brand. Codes appear on the face of the washer better. Nowhere in the manual that I had to personally download myself because it didn’t come with one. And oh did I mention that I need a step ladder to reach into the bottom of the tub? This washer should come yellow because it is definitely a lemon!

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

The washer makes holes in my shirts. Odors like perfumes are still on the shirts when they come out. Does not wash great. The dryer is good but does not take out cat hair. My old machine washed a lot better than this new one. I have mold in where you dispense the cleaning product and the way it is made I cannot clean it. I am so disappointed with this product.

Dryer needed to be serviced within 2 months. Drum seal fell out. Service was no questions asked. Fixed promptly. Washer works fabulous. Gets clothes clean. Surprisingly quiet. You do need to keep up to the sensors on the dryer. Must be wiped with rubbing alcohol to keep performance.

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

I bought the Washer and Dryer. All I can say about this washer is that it does not use water enough to be considered a commercial type of washer. Its balance is poor also for being so deep. I have to pour a bit of water on the clothes so the sensor thinks it’s a heavy load and do an extra rinse. And I saw that on a video regarding this washer trick. But I’m wasting more water cause I have to rearrange the clothes when done. I put the top ones on the bottom and start over. To me it’s a waste of effort sometimes I just go to the laundromat. They should consider their products if we all are complaining about this they should really do something. To me the washer is really useless.

I purchased a Maytag dishwasher delivered in dec 2012. We are snowbird Canadians and the dishwasher is only used 5 months per year. Jan 2015 the control panel quit working and the repairman tells me the wires on the control panel have started to melt down. He called Maytag and was told they had extended the warranty on this machine for one more year. Missed it by 2 months. Considering this was only really used one year, I am very disappointed. How can an extended warranty on a safety issue only be for one year? This is my first Maytag product and will be my last. I only purchased it because I was told Whirlpool bought them out and I have never had a problem with Whirlpool.

Shortly after having this appliance custom wired and installed into the kitchen cabinets above our gas range, we found that the microwave no longer worked. The window where the digital clock shows the time instead Showed SE. I hit the clear button and the microwave once again worked. This happened again on many occasions and the clear button corrected this malfunction. Now this has happened once again but nothing Ive attempted clears the System Error or reboots the microwaves brain. Ive contacted many appliance repairmen but as soon as I mention Maytag they inform me not to repair the microwave as it costs more to repair than to replace. Ive attempted to purchase a new circuit board and repair it myself but no one has the part available. This appliance was purchased in April, 2009. Can anyone recommend a Microwave Brand as a replacement for this disappointment?

This has to be the biggest joke in the world for the respected name of Maytag! The engineers that developed this worst-of-all machines on the market must have been circumcised with pinking shears. 80 minutes for a wash cycle? Even rapid wash takes an hour of slowly spinning and spinning ad nauseam with almost no water. The clothes sit in the same position even on the very brief agitation cycle... Nope, the clothes do not come out clean, although if you add bleach to the dispenser, since there is no water in the tank, the bleach does triple duty and rots the clothes. Is this masquerading as energy efficient when all of the cycles are an hour long, about? Unfortunately it takes water to clean clothes and the environ-lack-of-mentalists must have bribed Maytag to develop the worst washer on the planet. Absolutely!

Bought a Maytag HE top load washing machine (Model MVWB765FW) in Jan of 2019. As I write this the repairman is banging away on the machine to replace the gearbox that had gone bad. This is the second time a repairman has been out to work on the machine. The first time was to replace a bad water pump, which was when the machine was about six months old. Maytag would have you believe that Power and Durability Come Standard. So too, apparently, are visits from the repairman. To its credit it does a good job cleaning clothes - when its working. If youre going to buy this machine, I recommend purchasing an extended warranty - youre going to need it.

We purchased a new Maytag Bravo washer and dryer on March 4, 2011. On January 26, 2015, our washer stopped spinning the clothes. We purchased these appliances while preparing for retirement, thinking we would possibly never have to purchase them again. There is only two of us! Wrote to Maytag (when it was still Maytag) and got a response of So sorry **, we can fix your washer for $319.00. We could buy a new washer for not much more than that!!!!!

I purchased a Maytag dishwasher (model MDB7609AWW1) from Sears on 09/11/2009. Its control panel failed twice in 3 years. In 02/2011, after just 17 months, the dishwasher wouldnt work. Nothing happened when I pressed the start button. I paid $294.39 ($129 for a new control panel plus labor) to have it fixed. Now, 17 months after the control panel was replaced, it has again crapped out with the same problem. I see by all the complaints here that this is a common problem. I wish I had read all these complaints before I had the control panel replaced the first time. Maytag, shame on you! Never again! I called Maytag and Sears, and as you would expect, they said, Sorry, its past the warranty period. When I buy my next dishwasher, it will not be a Maytag and it will not be from Sears.

Not only does dryer come with missing parts and are told by Maytag 1 to 2 weeks for delivery or drive 25 miles to pick up one. You do not qualify for rebate even though you do not receive washer and dryer for 5 days after rebate starts. Should have kept my old GE was faster and got clothes cleaner. Was looking at a Maytag refrigerator not anymore with their service.

This is the worse washing machine ever. Wish Id never have bought it. Clothes come out unclean, washer cleaner cycle doesnt work, water level is almost none, etc etc. I could go on and on, you get the picture. Coming here and seeing 100s of negative reviews and complaints many of which I suffer from as well, just clarifies how bad this machine really is. There has got to be a way to bring a class action lawsuit or arbitrary suit against them. Im pretty confident that there are probably 100s more who are dealing with this shoddy washing machine as we all are.

First off, the drum split apart on the dryer. The drum part was not in this country, so instead of going ahead and replacing the clothes dryer, they told me to hang the clothes outside for six weeks or whenever the part comes in. That was three months after owning the piece of junk. I was having a bad day already, so I basically completely lost it. Im surprised I didnt get arrested for that. I wont ever lose my temper like that again. The clothes always smell bad, and sometimes really bad. Now, I find out that both washer and dryer could cause a fire. They are sending us a couple of really cheap GFCIs to keep them from a liability issue. Maytag is the absolute worst!

My microwave is just 3 yrs old. SE error. Yeah, what a crock...Such junk. However, if we would just manufacture everything in the USA not only would we get better quality, but we would have more jobs. USA stop selling out to cheaper countries and pumping out more volume for less overhead.

I could care less if Maytag responds as I have already advised all my family and friends to avoid Maytag products. After spending over $1200 to buy this refrigerator it took 6 months for the ice maker to failed, and it needed a control board replaced. Maytag had a great reputation; however, in the past 5 years their products are worthless. I also have a Maytag dishwasher which failed and was stuck on cancel with a flashing light. The dishwasher panel needs to be replaced and I have just decided to replace both of these products with a different brand.

We bought a Maytag Dishwasher Model # MDB4709AWW4 about 2 years ago. Complete piece of junk. Just spent $350 on a new control panel. We called Maytag and they told us that our model wasnt under the recall for this issue. The old belief about the Maytag repairman not being busy is a lie. Avoid their products. They are poor quality.

We spent over $1,200 on a Maytag washer on 12/2015 and it did not work properly. The door got locked, had a couple loads moldy because we could not get it open. Didnt drain either. Maytag had someone come look at it 3 times and it still didnt work. Called Maytag and now they told me that they cant do anything about it because is not under their 1 year guarantee. And of course they are very sorry for my unfortunate inconvenience. I thought they had a good honest reputation but... Im just disappointed!

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

I specifically bought the washer because it has an agitator and you have a setting for more water if you need it. My previous washer had no agitation and really miss that. Seemed like clothes got cleaner. On this machine the agitator is certainly helpful, but there is so little water sometimes I find a pair of jeans with dry spots when load is complete. No, I do not overload the machine. If I change the setting to add more water I don’t see a difference in the amount of water that comes in. I find myself frequently adding an extra rinse. I feel that while making the new washing machines eco friendly they have cut back on water conservancy too much. At the very least the consumer should have more options as to levels of water. I would not buy this brand again.

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

We purchased a top of the line, state of the art Maytag washer and dryer Neptune. The fill valve failed twice, flooding the first floor and the big storage room below. Thank God we were here! Now the thing halts mid-cycle and wont continue. The repairmen both said the design is messed up and they hate to work on the Neptunes.

I bought this Maytag refrigerator model MF 12269FRB00. It is not, user friendly, meaning that condiments and small bottles just dont fit conveniently in any space, The biggest issue is the ice maker. The ice maker shoots ice out on each and every attempt. Every time you want ice you are guaranteed to have ice shoot out of your glass on to the floor. I often challenge my guests to get ice without the cubes shooting out of the glass. No one has ever won. Dont buy this piece of crap, unless you find humor in having ice on your floor every time. Shout out to Grays Appliance in Melrose for selling crap! I will never buy from them or Maytag again. To the engineers who designed this product, you suck too!

I purchased a Maytag dishwasher at Home Depot in Roanoke, TX on 07-14-2011. Model Number: MDB7749AWB2Serial Number: F12604431Unfortunately, Ive just been obliged to open my third service call on this new dishwasher. The first service call was made in August 2012, just outside of the first year warranty period to repair a wire which had come loose in the control panel, making the dishwasher inoperable. The second service call (May 2013) was to replace the front panel housing and touch pad which had broken off at the screw-mounts holding it on to the door. As the handle to open the dishwasher is part of the front panel (which must be pulled out pretty hard to open as it does not have a latching mechanism) screws set into unreinforced, thin, plastic posts holding the panel to the door seems like a serious design flaw.The third service call which I placed last week (August 2013) is to address the fact that the dishwasher has become completely inoperable with no lights on the front panel and is completely unresponsive. To say the least my experience with this product (and by extension the Maytag brand) has been a serious disappointment. I guess the reason I no longer see those TV commercials with the lonely Maytag repairman is because these days hes actually really busy fixing broken down ** Maytags. I will never, ever buy any Maytag or Maytag-family brand appliance ever again.

My Maytag MDB7609AWW2 dishwasher was purchased on 1/2010. Last month, the control board only worked on the right side of the panel and the dishwasher would not run. I called Maytag to see if this was a typical issue with the washer, which they denied. I ordered and replaced the control panel but this did not help. After reading all these posts, I do not think Maytag is being honest with their customers. Also, it looks like even if I am able to fix this issue, it is likely to repeat. I think I will cut my losses now and buy a different brand of dishwasher. I will never buy a Maytag again.

Almost two years after purchasing the Maytag Bravo XL, I am fed up. I have the exact same problems as everyone else in these reviews. Soap scum left on dark clothes since day 1. I thought maybe I was doing something wrong. I have read and re-read the manual especially the troubleshooting guide and still have the same thing happen. Its very frustrating. I constantly have to re-rinse clothes because of soap, lint, dirt, etc left on clothes. I wouldnt give away this washer to anyone, I would rather burn it. I am currently looking for a new washer, the last one I had for 11 years was a front loading Whirlpool. I should have stuck with a Whirlpool, I still have the matching dryer no problems at all.

Gemini Twin natural gas range - I bought this range approximately 18 months ago. I thought it had all the features I needed and it looked good -- looking good is just about all it does! If you are a real cook I would suggest you avoid this range. The burner controls are preset and it is impossible to turn the flame very low if a simmering heat is required. If you are making meringues, again, the oven heat cannot be turned to a cool enough temperature. Ovens bake/broil unevenly. It takes forever to bring a pot of water to a boil, not because the flame is not hot enough, but because the pots sit far too high above the flame. Bad, bad design. Probably designed by someone who eats take-out!!

Maytag bottom freezer / refrigerator: What a low-quality operation these guys are operating. We have a 5-year-old double door unit, which is not a cheap ticket item; and we thought that Maytag was from the days of old. The compressor failed along with ice makers and some high-use parts inside. I can understand the plastic lids and guides wearing out with heavy use, but not the compressor. I called Maytag and was directed to their proud Tennessee Service Location. It might as well be in China, where the real owners are located. She said, Oh well, we build quality units that are to last 12 years. However, they are man-made, and you cant count on that being a positive thing. What arrogance. I might get stuck with another brand from Asia. But it will never be a Maytag or any other in their family of products. The repairman is really busy these days.

Maytag washing machine Model # MHWE500VW - 2 control boards only last 4 years. I paid top dollar, $1229.00 to be exact and the parts and labor are $659.00 with no guarantee that there wont be further problems. Technician told me that this is typical of Maytag products. Contacted Maytag and they told me to take a hike and have a nice day. I will attempt to get some help from the place of purchase, Hamai Appliance, Maui, Hawaii.

Maytag washer mvwc565fw: You have heard about how noisy they are & dont fill up enough water unless you set it on deep water wash. I cant get the right water temp. Its cold, cold warm. No hot at all. Sorry I ever bought the piece of junk. Only have had it a month too. The last washer I had it at least lasted 4 years. Wouldnt recommend it to my worst enemy.

We bought this brand new washing machine just 6 years ago. Went with a Maytag because they are supposed to “last forever”. Ha! Last weekend it stopped spinning. Water would drain but no spin cycle. Had a recommended repair person come out and he said it was unfixable. The bearings were shot. This is crazy. There are only two of us using this machine how could it be totally unfixable 6 after only 6 years. The average washing machine life is supposed to be 14 years. No more Maytag for us.

First bought a nice looking Samsung. Didn’t last 6 months. Upgraded to a nice Maytag with steam and have never regretted it. It’s been years of worry free and trouble free use. My Samsung dryer is on the way out the door and to be replaced with a Maytag too.

Clothes do not turn over in the wash cycle. The clothes at the bottom get plenty of hard scrubbing from the agitator but the ones at the top barely get wet and never move down to the bottom. Insufficient amount of water enters the tub. The repairman says the washer is working as designed. Neither Maytag or Lowes will take back the washer. Worst appliance Ive ever owned. Bummer!

I have owned my Maytag Bravo Series less than a year. After 4 repair calls, I called again. The service department was rude and hung up on me. He accused me of destroying the washer on purpose. They are the worst company I have ever dealt with. DO NOT BUY Maytag products ever.

The only complaint is the lights on the bottom quit working about a month after we purchased. It was nice to light up the stovetop when cooking. Now it’s slightly dark. I have gotten used to this. We spent about $8000 on all the matching Maytag appliances we purchased. I would love to replace all but not in the budget. I am a dissatisfied Maytag customer.

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.