Recently May 2019, bought a Maytag Bravos Washer, HE. Its now installed and so disappointed with this product. Not enough water to wash Clothes. Would of taken cashback from Maytag, but cant wait 6 to 8 weeks for cashback. 6 to 8 weeks after they have washer picked up. How long did we want to go without clean clothes, hummm. Problem was looked at by a professional appliance repair company sent by Maytag. His opinion, suggestion was, washer just didnt deliver enough water to wash clothes. I know its HE, suppose to me water miser, but Maytag Bravos just doesnt give enough WATER. How do we get clean cloth like that. As I mentioned in summary, I have added attachment close proximity to add water to washer raising water level to wash Cloth. Yes with proper water it does clean good, JUST NOT A AUTOMATIC WASHER now. Were only two, Rural NB, up to 3-4 washes per week, more when company around.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

Bought a Maytag refrigerator model #MFT2673BEW10 in 2013 for $2100, the ice maker has leaked for two years. Paid for service come out and look at it, ice maker is shot, three years old, and it is junk. Tried to get help from Maytag Customer Support, what a joke. I was hung up on 4 times, and never did get any type of help except your unit is out of warranty. Bought at the Maytag Store in Saginaw, Michigan. No help there either. DONT BUY MAYTAG!!! They are junk!!!!

Rather than go through all the things I dont like about this washer, just read all the complaints because that is my complaints also: bearings, not enough water in tub, clothes not getting cleaned. Just check out the lint filter and see the gray and dirty lint after a load and you will see it doesnt clean the clothes. Now, the motherboard is kaput! Cycles are all screwed up. Cost is $386 for motherboard plus labor and I will not put one more cent in this piece of crap.Listening to the salesman and consumer reports on the best washer to buy. All they are concerned with is energy savings and believe me when I say that all energy savings products are a joke because you give up operating ability for the sake of energy savings-- true of refrigerators and washers, dryers, furnaces and the like. I will be buying an agitator washing machine. The saving on water are not enough to give up clean clothes.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

No adequate response from Maytag. Unsafe washer. Will be taking this to consumer protection as my scrubs are coming out of the wash with blood etc. left on the articles, even with bleach used. Very serious for all concerned. If you have someone with shingles or any other transmittable skin disease in your household, do not use this washer.

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.

My washer is just past warranty and making horrible sounds! I have always liked Maytag but their quality is bad. I wish I had read reviews before purchasing my washer and want to tell anyone reading this to NOT buy one. My last Frigidaire washer lasted 15 years with minimal repair. Shame on you Maytag!!!

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

I didnt want something from Sears due to horrible experiences with them. Maytag is very reliable and the cost was reasonable. They fit in the small space available for washer and dryer. They have all the features I need. The only complaint I have about the dryer is that for some reason if the load is small, it takes longer to dry than with a full load. I have had them for about 5 years now. I expect a washer and dryer to work correctly every time. If its poor construction I would not buy it. I also expect an appliance to last many years with proper maintenance.

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

I have had this range (Maytag MER8775AS electric range) for 36 days. The hot surface indicator light doesnt come on (bulb is fine) and the heat elements turn on and off on their own when I am cooking. 36 days! This thing is junk! I am going to see if I can return it, even though it is outside the 30-day window.

My washer (Performance Series 4000) needed new bearings about 6 months after purchase. By the time the parts came in and after the A&E repairman rescheduled because he didnt know how to replace them, another two months had passed. Now, a year later and with no more warranty, the bearing needs replacing again! This washer is only 1 year 8 months old! The first repair cost well over $1,500 but was covered under warranty. There are hundreds of other people with Maytag washers having the same issues! Maytag is well aware of the defect and refuses to take responsibility. I would like to file a class action lawsuit against Maytag. Im in Tennessee. Please contact me. Thank you.

We went to Home Depot and bought a Maytag front load dishwasher and dryer and microwave 3-1/2 years ago. The washer and dryer were put in right away. The dishwasher and microwave stayed in their box for another year due to us remodelling the house room by room and the kitchen wasn’t done for a year. We put the appliances in and the dishwasher panel went out in October 2011. The washer in April 2012 started having a failure 8 when it gets to the last spin and rinse in which takes a lot of shuffling clothes to get it to finish its cycle. Then last night, May 14th, 2012, the microwave caught fire and all I was doing was brew tea in a glass Pyrex measuring cup not to mention the fan didnt work from day one. The whole house was full of smoke and it melted the plastic. So the most I got out of 3 of these products is 3 years at the most. This is very sad that we spent this much money and it lasted less than 5 years. I am writing this to warn consumers not to buy Maytag appliances. They should last longer than 3 years and are not cheap to buy. This makes me very angry and I hope someone takes this seriously and work on the problems before someone burns up due to these appliances catching fire. Our dishwasher had a recall shortly after we installed it due to the element catching fire and we had your repair man replace it.

I bought a Maytag front loader washer and dryer, plus the pedestals for each. In last August of this year the washer just stopped in the middle of a wash cycle. I placed a call to the customer service. The tech diagnosed and placed an order for a part and set an appointment for two weeks later, with a time window 1 to 5 pm. The person called at 5:30 to tell me he had an job before he could get to me. I had taken the day off to wait for him. I called and they ended up rescheduling, for two more weeks.. Tech came ordered different parts, tech did not show up. Tech came out again ordered new parts. Next week he arrived wrong parts. Washer still not extracting. New tech, new parts, new appointment, this was what happened throughout September and October. Tech was not happy with his job, stated that to me, would not do anything but install part, even if it didnt work. He took parts with him. The washer still not extracting. Last Thursday he didnt even have all the parts, made the decision to replace machine without discussing it with me. Told me Sears would call me in 48 hours. Received call today Tuesday. Go to Sears to have it replaced. None of the machines they offered are compatible with mine. I will have to purchase the pedestal for the new machine, plus pay the overage to get the comparable machine. Service appointment people were horrible, cold and rude. Sear store at the mall where I purchased my washer said that it was not their problem. Once we sell it you are in their hands. Have had Maytag for over 30 years. Will never buy it again. Will never buy at Sears again. Too bad I have to replace my washer with something from Sears. Not enough space to write everything I have gone through, the lost workdays, the extra expense of having to go to the laundromat, the stress of dealing with incompetent people and techs.

We bought the Maytag washer from Home Depot on 5/4/2011 and it quit working on about 7/2014. We had a repairperson look at it and he said the drive transmission is worn out. He recommended that we buy a different machine since the part does not hold up since the part is made out of a plastic fiber material that does not show up. We bought the Maytag because we thought they had good products but a 3 year life on a wash machine is not acceptable. It is installed at our cabin so we only use it part of the year on limited bases.

We purchased a Maytag Top Load 5.4 cu ft efficiency washing machine. May 2019. It was making a funny noise already mid October and we had 8 parts replaced. After that it completely stopped working. We have been without a working washing machine for 2 months now. The technician has been to our house 4 times. When he came on Dec 31st to replace the mother board, that didnt solve the problem. He says the washing machine can not be repaired. We have been fighting with Maytag Canada and Lowes since the beginning of December. Neither company cares. We will never own another Maytag product. The company are crooks.

Weve always bought Maytag, but this is our last time. The washer is just a piece of junk. It uses very little water and the agitator does not work. The clothes end up at the bottom in a ball. The water level is so low sometimes my clothes arent even wet. As I type this it has been stuck in the rinse cycle for 2 hours. It just keeps repeating. Maytag should have to replace everyone of the BRAVOS XL washers. I am no longer a loyal customer. I might as well go down to the river and beat my clothes on a rock. At least they would be cleaner. Shame on you Maytag!!!

Maytag MCT Washer & Dryer - I bought the largest capacity to save time. However even my 6ft tall husband has problems reaching the bottom to remove clothes. Even worse is the lack of water to clean clothes, washes so long it wears clothes and they are still dirty. I tried to improve on my old Neptune and Id love to have it back. I may have to junk this washer. The dryer is very slow. Buying this set was tossing my hard earned money in the trash.

Not only did I buy a Maytag washer for the brand name and trusted longevity, but because they were always a good product in the past. When my Maytag EZ-Epic washer drum failed after only owning it for two years, there was no effort made by any associate to cover this under any sort of warranty at all. To replace this part, I was quoted so much money that I could go out and buy a brand new one for the cost of the repair for this faulty part. I am extremely dissatisfied with the way I was treated because the so called product was out of warranty and I will never buy a Maytag product again. Shame on Maytag for ever selling off to such a fraudster of a company.

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

The machine has left pin-sized holes in finer clothing since we first used it. I had purchased the extended warranty so they were called out to repair the issue four times during the warranty. They replaced the drum, but I still get holes. I think it is because there isnt enough water to rotate the clothing and it rubs repeatedly against the same spot on the other clothing. I have a see-through lid and you can see that the clothing just moves very slightly in the same position. I separate all clothing that has a zipper or any trim that may rub against the finer fabrics, but I am still getting pin-sized holes. We requested compensation or a new machine. They extended the warranty. We have replaced enough clothing that we are now buying a new machine. It will NOT be a Maytag.

Never had a Maytag before I bought my house. So far the only complaint is there’s a broken piece that prevents the drawer from functioning. Otherwise, pretty good stove/range for the price. Do wish it was easier to clean without scraping anything up.

The Maytag Neptune TL washing machine has always been extremely loud! It smells awful and now our clothes too! I have found mold in the washer and cannot get it all out even with bleach. My children are extremely allergic to mold and they have had problems because of this. I am very disappointed in this washer and find it sad that no kind of action has taken place to help people who have bought them.

Didnt even want to put 1 star but that is the lowest you can give. Maytag microwave less than a year old paid $350. Door clasp broke. Took two weeks to send a repairman out, he came out and of course did not have the part -- took another week to get it. Fixed the door and then he crashed and burned the microwave shorted it out and now it is totally dead. That was 2 1/2 weeks ago. Maytag refuses to replace the microwave and insists that the same incompetent service company come out and fix it. Meanwhile I have to call Maytag every other day to find out when the correct part to repair the microwave will be in. Was told it would be in two days ago. Never got a call to schedule the repair, called today to find out they never even ordered the part. Here goes another week without my microwave. Not only does Maytag have horrible customer service, they manage to find unskilled repair techs with equally horrible customer service! Will never ever buy another May useless Tag appliance again.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

I purchased a dishwasher and stove from Home Depot. Stove has already been replaced twice because of faulty manufacturing and now the dishwasher, after 1 1/2 years no longer works due to the control panel. I called a repair representative of Whirlpool/Maytag and explained the circumstances. Their own customer service people indicate that it is cheaper to replace a product then it is to repair it. Shame on Maytag and Whirlpool that they move their companies to countries outside of the United States and they no longer stand behind their product. Shame on them that what use to be the best product around is no longer worth paper you print on. I will no longer purchase any product from Maytag, Whirlpool or Home Depot since they all seem to line their pockets from products they know wont last. One mouth is worth a thousand complaints and I plan on screaming from the rooftops!

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

We bought this washer before Christmas. I was very excited. However my clothes don’t come out clean. I am actually washing my white uniform with hands because each time I wash, dark scums remain on my clothes. I think that the machine sensor does not sense how much clothes are in there and how much water is required. This machine is very disappointing, it needs to be recalled. See pictures below.

My Maytag dishwasher Model No. MDB7759AWS1 caught on fire last night, inside the control panel on the top of the door. This was very alarming as it filled the house with smoke and caused some fire damage on the bottom of the countertop also. This could have easily caused a house fire and is very disturbing. When I called Maytag, they say this model is not recalled. In my opinion it needs to be. This is a huge accident waiting to happen in other peoples homes. Please beware. If the countertop would have caught on fire entirely, the house would have gone up in flames.

I had purchased a Maytag Front Load Washer Model no. MHWE300VW00 in 2009. Now the rear tub, basket, and belt are gone. I will never purchase another Maytag product and would not recommend them to anyone.

This washer had good reviews when we bought it, but now today the agitator is not working. I see there are now 100s of bad reviews of this machine most around the same 1 1/2 year mark. How unacceptable to have a large appliance like this break after such a short time. Ive called Maytag to see if there was a recall and there is not. They offered the extended warranty to me for $325 that would cover all parts and labor. Ridiculous.

I purchased my which I thought was a stainless steel French door refrigerator in 2011 that I was getting a great product. Not even 3 months later I was using my warranty to stop the leak from my freezer now. Mind you, I paid $1500 so I got it fixed. 3 months later I called for repair again... Getting annoyed because this time the freezer came off track. 6 months later were chopping ice chunks up to stop the leaking on the floor. This lasted until last October keeping towels and old clothes around the fridge to soak up the water. This is so embarrassing especially if you have company over. You have a pile of crap soaking up water. I am a wife and mother of 7 children. I cant afford to just go buy another fridge. This isnt fair... I spent hard earned money on that magnet attracting stainless steel fridge and Maytag could care less. Im so disappointed and broke. Now I have to scrap it.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

We purchased a Maytag dishwasher in July 2013. In October 2014 it stopped working. None of the buttons on the control panel would light up. The service technician diagnosis was that it needs a new control panel at a cost of about $200.00. We chose not to do the repair since the technician recommended against it.

I bought a washer and dryer a few months ago from Home Depot Maytag. My clothes do not come out wrinkle-free. They are very wrinkled, to the point where I have to iron the perma press. The dryer I just got rid of was 30 years old, and always got the wrinkles out of the clothes. So I am very disappointed in the way yours works. I dont know what you can do, but this is not good. Thank you.

I purchased an Atlantis washer in 2005 and assumed that Maytag was still one of the better manufacturers. How naive of me! What genius at Maytag thought it was a good idea to place the water filter inside the washer? Not only can you not keep the filter clean so that cold water will flow properly, even worse, if the filter completely clogs, the water will not stop filling into the tub which could, of course cause an overfill and flood. I narrowly escaped this scenario once. No one should have to stand and watch their machine fill with water to insure it stops. Now the machine is causing a grinding noise when agitating. I expect it to stop working any day. I will not buy another Maytag or Whirlpool, who of course now owns Maytag. And I will not pay another repair bill for the filter or any other part. The brand was once considered the best in America, now its just another brand thats a piece of junk produced in another country.

I purchased my Bravos (ecoconserve) washing machine in 8/2013 from hhgreg. The problem I have is this grinding noise with the spin cycle. So I unplug the machine because the lock lid light is flashing and wont unlock unless I unplug the machine. I grew up on Maytag so that was the reason I purchased this machine but never again. I am so disappointed in this product. :(

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

Purchased a Maytag dishwasher (Model #MDB7749SAW1) in January of 2013, installed in February. A little over a year later the control panel went out. I called Maytag and they were kind enough to pay for the part and I had to pay for the service. Now it is July of 2015 and the control panel is going out again. I called Maytag directly and talked with a service representative and the best they could do for me was for $269.95 they would have it fixed and I would have a one year warranty as well. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 2 1/2 years it is becoming a very expensive dishwasher. There should be a recall on this control panel. Very disappointed.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

Bought a Maytag microwave model MMV4205DS and I too have had an issue with open/close door display. Just like other reviews Ive read it started out once in a while for the first year then began happening more often til it stopped working by the second year. I also read someone asking why there isnt a class action lawsuit? Good question. Way too many bad reviews on same issue. If I knew how and if we could start one then I would. Thought we could trust a company thats been around for so many years. Wish we had check into it more and I have learned from other products to do just that from now on. Have a backup microwave by GE from WalMart weve had for 10 yrs still working.

We have had a Maytag dishwasher for just over a year. The control panel acts up randomly and has finally quit altogether. The design of the handle is very poor as it pulls the control panel away from the door. Will never buy a Maytag product again. This is a very clear design flaw and when we called Maytag they offered no help as we are passed the guarantee.

We bought our $600 Maytag dishwasher less than two years ago and have had three separate problems with it, from faulty instillation, to a faulty seal to faulty control panel. The first problem was covered under warranty, the second problem we fixed ourselves and the third problem, nothing can be done except pay an additional fee of $250+ for a new part. Maytag used to be a good name but with three problems in under two years, the only guarantee given is that if you buy one, be prepared for problems. This company does not stand by their products and will only ask for more money to fix their faulty items.

Maytag Bravo XL -Model MVWB88OBWO. Washer quit after 13 months of light use. Repairman came, $148.00, worked on just a few setting for 4 loads. It has a bad controller and some other part. Total cost of repair, if I was stupid enough to make it, $650.00. Guess whats going to the trash. I guess that kind of negates the ECO-FRIENDLY, huh? I will NEVER own another Maytag appliance.

I have had my washer and my dryer (model no. MGDB850WQ - serial no. MJ3311087), for 1 and 1/2 years. I have given both plenty of time and since the beginning, I have literally hated these products. This was a large purchase, so I feel locked into a terrible choice. I wish I had never bought these two items and will never use Maytag again. I will also never recommend these products to anyone. I do not like the new technology.

I purchased a Maytag Dishwasher in March 2013 and the control panel failed in July 2014. I, along with hundreds or thousands of others it seems, discovered that this is an extremely common issue with several models of Maytag dishwashers. Rather than standing behind their products and making it right for their customers, Maytag is hiding behind their one year warranty and refusing to do anything about it or even admit they installed thousands of FAULTY control panels. This has been an expensive, infuriating issue to deal with and I have never been so dissatisfied with a company. Bottom line, they made a bad product that should have been recalled. It blows my mind that they are getting away with this. I wish I had known the recent changes in Maytag/Whirlpool and I wish I had done my research prior to the purchase.

I have bought 2 high end top loader models (Maytag centennial commercial), brand new both from Home Depot. The problem is Maytag is making them cheaper! Suspension is coal springs that suspends the load so if you fill it up, it lowers the drum to the floor, instead of a bottom bracket that supports the weight from lowering the drum to the floor! Second is the pulley system with the belt drive that wears through the plastic casing. You know some people dont have $900 or $1,000 for a machines that says commercial or heavy duty that only last 4 years when you have a family of six! Very very sad, will never buy another Maytag.

MDB8959SBB. Purchased this Maytag dishwasher late December 2013 and had it professionally installed on January 4, 2014. Could have burned down the house this weekend! Smoke everywhere! Thank goodness it was running during the day and not night so that we were able to shut off the power. Lights in the kitchen were blinking and smoke pouring out of the dishwasher. The house still smells of smoke. So disappointing. Ive always been a proud owner of the Maytag products. Never again. Especially after reading the reviews. Interesting enough, THIS dishwasher was purchased because of a recall on the PREVIOUS Maytag dishwasher I had trouble with. They gave me a credit to use towards my next purchase. Ive learned my lesson.

Purchased this washer from Saginaw, Michigan location in 2007. Started sounding like it was going to come through the wall of the laundry room so I contacted repair service. Told bearing was bad and that cost of repair would be $1,000.00 - literally laughed at repairman. I find it difficult to believe that a washer is built to last 7 years after paying so much for it.... My years of purchasing solely from Maytag have thus ended.

The refrigerator works well. No problems. Easy to move to clean behind it. Good value. I havent had any problems since I bought it. Keeps a steady temp; Its exactly the size I needed; has plenty of space. Its a plain fridge with a reasonable price!

I am 86 years old and have happily owned Maytag washers for many years. I just recently purchased the front loading model for ease of access. After using it for sometime, I could not be more disappointed. The clothes come out smelly, stained and gray. I tried using affresh washer cleaner on hot setting and the tablet did not even dissolve. There is black mold growing and must be cleaned constantly. I am so sad that my favorite company has let us down. I cannot afford to buy another washer so I am stuck with this lemon!

I bought this washer three years ago. It is the worst washer I have ever owned. Washing a load of clothes, it goes off balance constantly, large load, small load...it doesnt matter. The smell because of low water usage is awful, and the clothes dont come out clean. I have to buy a new one and that really stinks. Maytag youre off my list for purchases. These days its quality that will keep you in business. We are too smart for this garbage.

I have filed a class action lawsuit against Whirlpool for their faulty control panels in their Whirlpool and Maytag dishwashers. Please contact my attorney, Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 and let them know if you own or owned a dishwasher with control panel failures.

We purchased our Maytag Bravos washer and dryer in 2008. Within a year, the hinges that held the door open on the top load washer broke. In year 2, the area around the fabric softener dispenser rusted so badly that it almost completely ate the porcelain enamel away. In year 4, it started making a noise that I will compare to a jet on takeoff during the rinse cycles. It continued to work but got louder and louder. We looked into the cost of the repair, which was going to be $350 parts + labor. If it had been a good machine, we might have considered fixing it but it wasnt. Even a set of sheets could put it off balance, which stopped the machine with the wash cycle incomplete. It also set its own water level based on the weight of the clothes and many times the top items came out with dry spots that hadnt even been submerged throughout the whole cycle. Consequently, the clothes were never very clean and I would have to rewash many loads. This machine was not cheap - around $1,000. I was so frustrated and felt completely taken by the Whirlpool company again. We have had many unhappy situations with their products over the years - Kitchenaid, Jenn-Air and Maytag. We finally learned our lesson and researched washers online. The best rated that we could find was Speed Queen. We couldnt find it in Canada, so my husband drove 5 hours round trip to the US and bought one. We have had it 4 months now and the difference is unbelievable. Our clothes are clean again. I can set my own water level and the hot cycle actually gives you hot water. It never goes off balance no matter how many or few clothes it has. If I see that I need more water part way through a cycle, it has a button that lets you add some part way through. It doesnt have a lot of bells and whistles. Its a basic but excellent machine that is a pleasure to use. I would recommend it highly. I realize it has only been a short time, but my Maytag never performed like this machine even from day one. It reminds me of my very first washing machine many years ago, an Inglis, which never had a repair in 15 years of use. If our dryer goes, we will definitely buy Speed Queen. The trip is well worth it.

I purchased a Maytag Bravos washer and dryer pair in 2009. Over those 5 years I have had at least 8 shirts come out of the washer with tears in the armpits. First I thought it was my armpits destroying the cloth. Then I thought it was cheap cotton (all my shirts are 100% cotton) from foreign manufacturers. Ive had two shirts destroyed this week, this mornings was really thick material. Usually when I remove clothes from the washer, they are entwined and twisted. Consistently when I wash any load including a towel or two, the washer becomes unbalanced. My clothes often have a foul odor after washing. My theory is that the lack of a center agitating spindle is allowing the clothes to tangle, and not really cleaning them. I have to use the extra rinse setting or the clothes come out covered with soap suds. In summary, Im not happy with this washer and will never buy another Maytag appliance. Im also not sure the high-efficiency technology has had all the kinks ironed out.

Maytag wont fix new washer. Service person came 3X, but it still wont go to rinse cycle. Last 2X Maytag said service scheduled, but no one showed. MT mgr said cant help & to just keep calling back.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

I am a WWII vet. I bought a Maytag dishwasher 4 years ago from Home Depot... Cost me $600 in total repairs. Maytag would not help. My son just brought it to the dump! At that same time I bought a Maytag bottom freezer from Home Depot... It has never worked right. Ice dispenser broken after 1 year, food freezing in fridge at any temperature... It just died! Maytag refuses to take any responsibility for THIS POS!They should be ashamed at the way they treated me. I am 94 years old, and have fought for our freedom, and was looking for one simple thing from this American company. Its called fairness! Maytag sucks! You have lost a lifetime customer. You have lost my son as a customer, and will lose anyone I talk to, as well as my son posting on ALL social media! SHAME ON YOU MAYTAG! SHAME ON YOU MAYTAG!

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

I love using my microwave because everytime I am in a hurry, like going to work and my kids to school and dont have time to cook or we dont like to eat outside fast food I cook healthy the night before and microwave it the next day and it just feels like the food is just made. It taste so good my kids and husband love it.

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

We purchased a Maytag refrigerator in 2009. The freezer is on the bottom. In the last 3 months weve had to defrost this frost-free refrigerator. The freezer frosts and the refrigerator went into the danger level for foods. A technician said there is a tube from the freezer to the refrigerator that gets blocked with ice and your food is spoiled in no time. I wish I would have read this website before I purchased a Maytag. Hopefully, this will help someone else. I thought that Maytag was a quality name. That was the good ole days and now Im living in the good ole days defrosting a frost-free refrigerator. Beware!

The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

Maytag Bravo washer and dryer delivered 2 days ago.My complaint is with the washer. I didnt know it was HE and that it requires special detergent! I didnt know the lid locks! I didnt know when I push the hot water button, the machine mixes in cold water! Complicated, delicate machine and not user-friendly. I dont expect the washer to last long.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

MDBH979SAM0 - Bought this dishwasher from Home Depot 2 years ago and have taken care of it, never abused it or anything. All of a sudden it just starts freaking out, once you start a cycle it will wash and then rewash and then keep going costing us money on electricity, water and wear and tear on the machine. Ive tried everything but it seems like its just stuck in start mode. The indicator lights on the panel flip out too, they will all blink randomly. So when I close the dishwasher and dont intend to start any cycles and it is off it will start up all on its own so Ive had to unplug it. Funny how I called to order a control panel part and its on back order... Very interesting how they are out of this part probably because everyones ordering it.

We bought a new Maytag electric range from a local dealer three years ago. The oven element quit working, which shorted out the motherboard that controls the entire range. The cost of repair was $500 for the element, motherboard and installation. We have owned other brands that lasted 20 years and worked fine with no repairs. My folks have used Maytag for over 50 years with no problems. Who and where is this junk manufactured now? China? I will never buy another Maytag product!

Does not clean properly! Water level is too low for clothes to move around properly. This appears to be a very poorly engineered product. We have had Maytag products for many years. The only good thing I can say about this product is that it beats a scrub board. Would not recommend Maytag product to anyone. Looking at other complaints it appears that Maytag is doing nothing about this. Will try to sell this at a yard sale and hope no one asks my opinion. Then go buy something that works.

I wish I would have read reviews before I purchased this washer, but I was in a hurry to get a new machine. Maytag has a great reputation and we went on that!! My Bravos is 2 months old and we have been away for a month! What a disappointment so far. What Ive noticed is all my dark items have residue on them, and today some of my light clothes came out looking like there is grease on them. Im afraid its going to wreck more clothes! Does anyone know if theres been recalls on the Bravos XL washing machines?

My 14 month old Refrigerator made a popping noise and quit working. I called Maytag and I had to pay $299.00 for a Service Plan so the repairs would be covered under a warranty and A&E Factory Service came out to do the repair. The repairman told me the Circuit Board and Compressor were melted and he was surprised it didnt cause a fire. The repairman had to get authorization to order the parts for this repair because they were so expensive and he is not even sure if the repair will fix the refrigerator. It is going to take 2 weeks for the parts to come in which means I will be without a refrigerator for a total of 3 weeks and were not sure if this will fix the problem. I am being told by Assurance (the warranty company) that they have to replace the parts 3 times before they will replace the refrigerator. I asked them, Exactly how long do you expect me to go without a refrigerator before I get mine fixed or replaced? When I called customer service and spoke to Brittany she gave me her standard robotic answers. I asked to speak to a manager and she sent me to the never-ending hold zone. I called back and non manager was available but they took my name and number and assured me that someone would call me back. I am still waiting for that call.

We purchased washer at Sears 6 years ago. Have had same issues for 5 or more years. Sears has been out to check it 6 to 7 times! They clean it out, tell me to use (expensive) Affresh tablets monthly, problem solved but it never is! When we run our washer and walk in laundry room it smells like a sewer. If we open lid its even worse. I use Norwex all naturally, biodegradable laundry detergent. There is nothing Ive done to create this smell. Its a manufactured problem that probably relates to ALL the other issues with this crappie washer that Maytag will do nothing about. I called Sears for 7th or 8th time, said they could send someone out AGAIN, I said thats a waste of my time and yours. They told me to call Maytag. They wont do anything (warranty is up). Of course there are NO ISSUES OR RECALLS on this washer and obviously there should be with not ONE good review! Im angry. You all should be too. We paid good $ for a product that used to have a good name and they are screwing us. I think we should ban together with a class action lawsuit. Please give me your thoughts. They know something isnt right and they shouldnt get away with this.

I purchased a Maytag dishwasher on Nov. 5, 2013 from Freds Appliance. I had to have the control panel fixed twice and it failed again in June 1916. My stemware had a film on it and I either had to wash it by hand or rinse it in hot water and dry by hand. Thus I felt like how could my other dishes not have this film on them even though I faithfully used Finish. I have 2 daughters who live within a half mile of me and they did not have this trouble with their dishwashers. I always felt Maytag was a top brand, but I replaced my 3 year old Maytag with a Whirlpool that my daughter and her family of 4 used for 19 years. Guess what... my glasses come out sparkling without using Finish and they wash in half the time and are dry!

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

We purchased a Maytag refrigerator (freezer on top) model m1txegmyw00 in May 2012 and the compressor recently failed roughly 3 months from the two-year mark. We first noticed the issue this winter when the bottom level of the fridge start freezing our food. We adjusted the internal temperature setting down, but this did nothing. Then the compressor started cycling on/off for roughly 5 minutes at a time. After we noticed that, the freezer no longer kept things frozen. We called the Maytag repairman ($80 including taxes just to visit). He said the compressor is gone and that They dont make them like they used to. - I thought he was joking. He also recommended getting a servicing contract on a new fridge (but I would expect that from a serviceman). The cost to replace the compressor was over $600 and their work is only guaranteed on that part for 3 months (so anything else in the fridge could go wrong). I asked if we could have avoided this - he said it was possible that if we had unplugged the fridge for 10 minutes when we noticed the on/off cycling, it might have given the fridge time to reset (so take that for what it is worth). Our previous fridge lasted over 8 years - I dont understand how Maytag (owned by Whirlpool) can sell a high ticket item that will work for less than two years. I will not be purchasing another one.

Water level is totally inaccurate, if you do get enough water in it, it will not spin clothes dry. This is the worst purchase I have bought in my entire life. This washing machine fails in every aspect period!! AND the matching dryer is a waste of space as well, clothes come out damp regardless of setting or time period. When I was younger, Maytag meant something, not anymore! I have searched to see if there are replacement sensors, or upgraded components to make these machines work properly, that I would even be willing to pay for myself and get them installed to make them functional, but NO they dont even offer that... we are just stuck with them. My water bill is higher and my electric bill is higher too! From these machines. I wouldnt even sell them used to another person. I wouldnt want them to inherit these problems, but as soon as I can save up enough money {being disabled} I will get these hauled off and buy a set of Speed Queen machines. My wife and I are so repeatedly disgusted!! I wish I had the receipt so I could post it for more proof.

Updated on 08/13/2021: Today a repairman who is authorized by Maytag came out. He found the problem, some arm that popped out that is located underneath the washer. He put it back together and said he needs to order the part and it will take 30 more days. Set the washer so that it SHOULD work for a couple of loads. I spent $700 on a washing machine and I have to go to a laundry mat to get my clothes washed. Here is the clincher. The guy left no paperwork, nothing, not even a business card. So I am at the mercy of this repairman (I think he said his name was Jessie). The guy was friendly, quick and knowledgeable, however he told my husband he knew what the problem was going to be, if you knew why didnt you bring the part with you and he said the part is out of stock. Why, is this part unique to Maytag washers? So I am still waiting for my washer to be fixed.Original Review: In December 2020 I purchased a Maytag washer it was delivered in January 2021 and it worked great for the first several months. Then the machine started making noises, clicking noises like it couldnt move through the gears. Then I started noticing that my clothes were not getting cleaned. It was taking an hour to wash the clothes. I told my husband it is not agitating just clicking. We had to stop and start back up the washer just to get the water level high enough for the so called deep water wash. I was finding residue left on my clothes and had to wash them 2 or 3 times to get the clothes clean enough to wear. Sometimes it wont spin enough to empty the water in the tub. It smells almost like wire burning. It has barely been 6 months and I have to have a repairman out. I will review the washer again after it has been fixed or replaced. But as of right now I will never buy another Maytag again.

My 16-month old dishwasher, which is not being used everyday, broke its control panel. Maytag will not fix it for free because they only back it for one year. This is a major appliance, shouldnt it last more than 16 months? The cost to repair is almost as much as a new dishwasher.

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

This is a wonderful washing machine. For cleaning clothes it does exactly what you expect from a washer. We have had 2 Neptune front loaders. They, however, have a couple flaws I dont want to live with again and will be looking for one that has come up with the solution to them. One, the bearings on them need replaced on a periodic basis or it sounds like a 747 taking off. Two - the front gasket around the barrel has a mold problem no matter how much you try to keep the thing clean. Other than that, these machines perform fantastic.

We updated our 25 years old dishwasher, which ironically still worked, to a Maytag we bought at a BrandsMart in GA in November 2010. Sixteen months later, the unit just died. The panel would light up, but would not run. We contacted Maytag and were assigned a repairman (The Appliance Guy) who could not come to fix the dishwasher until 5 days later. Once he finally showed up, I was informed by him that the control panel for the dishwasher had two shorts in it and it would be cheaper for me to just buy a new dishwasher because the repair to this one would be $344.44. When I contacted the customer service for Maytag, they offered to let me pay for the repairs and then they would give me a six month service warranty for free. Does that make sense to anyone? I could buy a totally different brand, brand-spanking-new and have a twelve month warranty with a better product. I asked to speak with Cheris boss and got to speak with Aaron, who offered me the same spiel. Heavily scripted, I apologize that you are dissatisfied, but all we can do is give you the service warranty for six months after you pay for the repair. I asked him if he was reading a script and he replied no. Now I know that he had probably repeated these same words twenty times a day. Heres a thought, Maytag claims to be a green company, using less electricity and water, and saving the customers money and yet they are filling up all the landfills with these appliances that are not even five years old. How is that being a green company?You know how when you buy a nice new button-up shirt? The makers of that good quality shirt go ahead and sew an extra button on the inside bottom part of the shirt because they know that theres a chance youll lose a button. Well, Im thinking that Maytag should just start shipping a couple extra control panels in every box of Maytag dishwashers. Crazy idea, right? Okay, so an easier and cheaper way for Maytag to correct the problem is to stop making dishwashers. Go back to the drawing board, make the engineer who designed the control panel wash everyones dishes (as punishment and he can get help from the customer service people because theyre really doing nothing), start building the old design dishwasher that has the old switch and dial, and start respecting their customers. There, problems solved!

Maytag Bravo 300 Quiet Series - Bought this Maytag 5 years ago because Ive always had good experiences with them. After 3 years it started making rattling sounds so we had someone come out and fix it for around $275.00. 2 years later its still rattling, leaving black grease marks and putting holes in the clothes. Will not complete cycle unless it is unplugged, reset and plugged back in. I give up, I just bought an LG. I will never buy another Maytag washer again, still have the matching dryer though.

Worst brand ever. They both broke at the same time. Spend too much money. Never buying these brand again. Maytag sucks. Dont buy Maytag washers or dryers.

We have a Maytag Neptune washer we purchased new in 2001. The Neptune was useless on My mechanic clothes, but good for delicates and blankets so we have an old style washer to clean my regular clothes. The Neptune was at work on a blanket when we smelled it burning. With it unplugged, I got around to investigating the situation and found the motor control was shorted and burned. I tried calling Maytag. I was asking about an upgraded part or recall. They didnt want to help. The representative was condescending and after I listened to her attitude, she said someone would be in touch. NOTHING. Now I see these suits and I guess I understand. My house could have burned down - they dont care. Maytag is garbage and Im sorry I ever thought otherwise.

Apparently the Maytag Bravos HE top loading washer is poorly designed. We have sparingly used this washer for approx 3 years and it began to make a horrible noise in the spin cycle and then to give us UL error codes. After searching on the internet we discovered that the seal around the main spin shaft and the bearings were bad. Inspection under the machine revealed a terrible rust and grease spot and splatters of rust and grease on underside of unit. This is a typical problem and this machine should have been recalled or at the very least repaired by Maytag for little if any cost. They now make a kit to fix this problem, but this should not happen after only 2-4 years of use on a $700+ machine. Very, very disappointed with Maytag! Customer service, of course, offered us nothing as pathetic 1 year warranty was expired. Ten year on the tub, like anything will go wrong with that.

We purchased this model from Home Depot in February 2011. In July 2011, I found it full of water and dirty dishes after running a wash cycle. It was completely dead like it wasnt getting any power. I checked the fuses, etc. - nothing was wrong that I could find with the power supply. I called for a service tech that day and they sent someone out to check it. It was the control panel. They shipped me a new control panel and the tech came back to replace it under warranty. It worked great until July 2013. Again, it is full of water and dirty dishes, wont turn on and has no lights on the front panel. I called Maytag to get a service tech. The warranty is expired of course. They offered to sell me a replacement dishwasher at a discount for $409, Model # MDB7749SBW. Or I can buy an additional 1 year of warranty for $269. I also could buy a control board for about $150 online. None of these options is attractive right now, but hopefully if I get the new model, it will not have any issues... I wish they would just tell me it was a crap unit instead of giving me the option to either get a new one or pay for a useless warranty. I am fed up with this dishwasher. 2 control boards in 2 1/2 years is unacceptable and indicative of a defective unit or design. After reading the reviews here it appears to be a defective design.

Our Maytag refrigerator is leaking water all over my kitchen floor to the point that my floor tile has lifted. The ref. is a French door with water and ice in the door and freezer on the bottom. We have been cleaning up puddles of water at least several times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasnt ConsumerAffairs demanded a recall on these expensive defective refrigerators to date? I am truly disgusted.

I grew up trusting and believing in the name brand Maytag. Unfortunately, I wont anymore. I purchased a Maytag MDB7749AWM1 dishwasher from Lowes thinking that I would not need the extended warranty because well it was a Maytag and they just keep working and working for years to come. Not true anymore. 1.5 years after the purchase the control board has gone out. I come to find that hundreds upon hundreds of people have all experienced the same thing. Shortly after the manufacturer warranty expires, the panel dies. By all accounts it is an issue of POOR engineering and Maytag now being produced by Whirlpool. The replacement part is between $150 and $200. Thats about half the purchase price. It is a racket. Companies like this probably think, well if we build something that is going to last and last we cant make money on that. So lets rig it so our stuff breaks right after the warranty and charge half the price of the unit to fix it so we continue to make money either by people buying the part or just going and getting a new dishwasher. Well I can tell you I will be getting a new dishwasher and it certainly wont be a Maytag OR a Whirlpool.

Maytag Bravo Washer - I recently purchase a fairly expensive washer built by Maytag. In my opinion it is the worst washing machine I have ever owned. Again in my opinion their advertising about being such a reliable company should be considered false advertising, and near criminal. If you had a lower rating I would use it. Absolutely you should never use the word Bravo in a description of this washer. I will never purchase a Maytag appliance again. Check the internet for reviews before you purchase. I had just came out of surgery and in a wheelchair and trying to move back home and didnt do my homework.

Last year we replaced a Maytag dishwasher which had a faulty control panel after just a few years of light use (There are just the two of us). It was going to cost almost as much to repair it as to buy a new dishwasher, so we opted for an $800 model (MDB8959AWW6) with a control panel across the top of the door. There had been a recall on that first Maytag for the heating element or something, so we decided to put the credit towards a machine that would last us for years, we hoped!We have been in this house for 18 years and the original cheap builder-installed dishwasher lasted for 12 years. In fact, there was nothing wrong with it when we replaced it with the last one. Whatever happened to the lonely Maytag repair man? We did not buy an extended warranty, but I can see now that probably these things are only meant to last the lifetime of the warranty.We are semi-retired and cannot afford to have the dishwasher repaired, so it will be a decoration in the kitchen from on. Never ever will I recommend Maytag to anyone! One bad experience should have been enough, and we probably would not have bought a Maytag again had it not been for the credit we got for the product recall on the last one!

I have a Maytag washing machine (MDBTT53AWW1). The total cost is $524 for machine plus installation. And the cost of yearly repair on this machine is $300.I purchased this machine a year and 10 months ago in January 2010. A few months ago, the control panel started to only light up partially but the washing machine continued to run. A few days ago, when i tried to turn on the machine, it would not work--the control panel was no longer lighting up. I called a repair man recommended by Lowes, and after explaining the problem over the phone, we scheduled a time for him to come (ten days later was his first available opening!).Ten days later with a broken washing machine and doing all the washing by hand, the repair man came late. When I made the appointment, I was told he would come anytime from 8 to 11 a.m., and of course, he did not show up until almost 1:00 pm. When he finally arrived, all he did was look at the model and determined instantly that the reason our control panel was no longer working was due to a faulty design. This dishwasher allows the steam to escape through a small vent placed to the left of the control panel. The steam inevitably causes a short circuit, meaning that this will be a reoccurring problem every year.He did not dismantle anything and was in my home for no more than 5 minutes. I was told the cost of a new control panel would be $141 plus his labor fee of $137. So all in all, if you purchase a Maytag appliance, the initial cost is irrelevant. If you purchase a Maytag appliance, you will spend almost $300 yearly to maintain it--basically the cost of a brand-new washing machine.Something needs to be done; this is unacceptable. The least Maytag could do is provide all of us, fools who believed in their product and thought that they were of quality, with a free10-year warranty for this faulty machine which is pre-determined to break down every year as a result of their poor design planning.Cost aside, what kind of world are we living in that major appliances are made to last just one year and then are to be thrown in the dump? There is no way I will pay $300 for the next ten years to maintain a product that is made to break. That is wasteful and disastrous for the environment. Shame on you, Maytag. You will be filling landfills around the country with your terrible products, and the world will be a worse place for it.

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

The Maytag Bravos XL Gas Dryer I purchased less than a year ago has stopped working three times. The dryer stops producing heat. I am now about to call Maytag repair again and waste time and energy setting up a warranty service call. I spent a lot of money in order to go to the Laundromat on a Sunday. Do not purchase this dryer if you would like to be able to dry clothes at home with any type of consistency or confidence. Arrrggg!

So our 4 year old Maytag Dishwasher just took a crap. Thank God we were at the kitchen table when it started to smoke, which smelt like burning wires and unplugged it immediately. Repairman came out and said it would be a 3 to 4 hundred dollar repair. What happened to the great 10 year Warranty? Oh yeah, its a limited warranty which does not include wiring. Could have burnt down my 4 year old home, but thats ok, not covered. The good news, the upper arm I replaced due to wear and tear would have been a free repair, because it would have been covered! No more Maytags in this home, ever!!

I have a Maytag MEDC200XW3 model. Good price reliable and rugged. It washes all the way from my delicates to my husbands heavy fire protective clothing with no problems. Holds lots of clothes with no issues either!