Purchased the Maytag MMV405DS Microwave and matching refrigerator from Best Buy in 2016, they were exactly what we had been looking for. Little did we know of the problems we would have with the microwave. At the one year mark the infamous open/close door problem begin. Luckily we were still within the warranty period since it was repaired at no charge. However six month later the problem re-occurred, we are now out of warranty and have little recourse. Maytag should have by now have come up with a fix. I find it hard to believe they are still manufacturing this microwave and selling this product knowing it will fail. We have little choice but to replace it with another brand which will not match. Suggest anyone looking for appliances stay away from Maytag.

I bought this after having a Frigidaire for 40 years and was immediately disappointed upon installation. This OVEN, not a range, was smaller inside and a lot of new pans would not fit! I have replaced the burners and the bulb wiring several times. Would not buy another one!

I purchased my Maytag washer and dryer set from the Maytag store in Glendale, AZ in September 2005. I even bought the stands for them. With my purchase, I got the extended warranty for four more years. I didnt realize that I would really need it. I have had so many issues with the washer and dryer I cant even count - from the control panel not working, to the noise and the vibration when washing, or maybe in the smell of moldy cheese. I also have issues with the constant chimes of D5 code that keeps coming up on the display screen. After 2009, I finally gave up on calling the Maytag customer service folks to have someone come and service the washer because it was out of warranty. I just decided to live with all those issues.As far as my dryer goes, the rollers went bad and that was replaced. The burnt smell isnt so bad as long as you use a wire hanger with a sock on the end of it and clean the inside of the vent. Then try to vacuum it, take the sock, get it wet, and clean the inside of the vent again. This was the most expensive piece of junk I have ever purchased in my life (almost $3,000.00 with the stands and warranty).What really gets me upset is I had the Maytag people servicing my washer and dryer up until 2009 and no one told me about a recall of my washer and dryer. The only reason I found out about it was searching for the specs as the washer finally died and I am replacing it. Trust me. I will not be purchasing a Maytag. I know that Whirlpool purchased Maytag so I am not even going to consider Whirlpool either. Since Whirlpool purchased Maytag, Whirlpool should have contacted all Maytag consumers, (which they didnt), put ads in newspapers (which I did not see) or put an ad on TV. None of these appeared to have happened.By the way, when I bought my Maytag appliances, I was supposed to get a $200 rebate for buying the stands that never came. It must have gotten lost in the mail - as well as the Tide coupons for three years. You, guys, remember that too. I will never ever purchase a Maytag appliance or Whirlpool, since they own Maytag now.

We purchased the Bravos X set (Model Number: MEDX700XW0 and Model Number: MVWX700XW2) form Lowes in October 2012. When the items arrived and we used the dryer for the first time in the delicate setting, the machine kept cutting off! So, Lowes brought us a new one. At first it worked but then the delicate cycle on that machine ended up not working as well a few months later. I ignored it and used the other settings. Yesterday, the washer broke. The entire basket detached! We were washing a small blanket and sheet set and kept hearing a loud banging sound. I went to check and the clothes were soaked and the entire drum was detached. I am so friggin angry! We spent over 1200 for this set and less than 3 years later, the set is ruined. I am on the phone with Maytag now b/c they need to replace this set or give us an upgraded set. They know that this set had issues yet they decided to still market and sell it. I want to sue!

This washer is the worst! Dont buy it! I paid a huge amount of money only to have it break down in 3 years! My husband and I live without children so our use is minimal. The spin cycle started to make a noise sounding like an airplane taking off. The repairman said it could be fixed for $800 and his service call, he told me that there were over 2400 complaints with this washer for the same product. He also told me not to use it while Im out to avoid the risk of flooding my home! Save your money and DONT BUY MAYTAG products.

Maytag HE Top Loader Washing Machine: I have regretted buying this piece of garbage since my first wash. This washing machine is complete waste of money and a piece of garbage. The Auto Sensing doesnt work and doesnt cover the clothes with enough water. When the deep water wash is chosen the clothes just float around but the agitator doesnt get them clean. Dont waste your money hoping it will work, because it wont. Maytag used to signify quality that is no longer the case. I am going to also give a bad review to the place I purchased this piece of garbage because all stores need to discontinue selling this junk.

Im an 78 year old man, married in 1962. In all the years and two kids we have had just three Maytag washers. To me the gold standard of quality washers. When the motor went out in our 15 year old Washing machine I considered replacing the motor, which is well within my capability. I am a journeyman industrial machine repairman formerly with Ford Motor car company before retirement.Instead, my wife and I bought a Maytag top loader high efficiency washer from Best Buy. I was skeptical when I examined the new machine with paddles instead of the agitator. Trusting that Maytag had engineered a water saving washer using paddles, I made the very poor decision to buy it. I regret not replacing the motor in my old machine. Boy was I wrong. Given the chance I would trade my new machine for the old in a heartbeat...The old machine washed everything we could throw at it. The new machine wont wash anything to my satisfaction. The bedding deep fill cycle is the only one capable of a passable job. Even then I would like a soak cycle which, in my opinion, would vastly improve results. In all I would characterize this as a total engineering failure. Why Maytag would allow this POS to be sold, where the reputation of Maytag is totally destroyed, is beyond my comprehension.

This is probably the worst place ever to buy any appliances. They are extremely unreliable and the technology on them sucks. If you wanna buy new appliances I highly recommend you spend your money elsewhere. The customer service is extremely horrible and is a disgrace. Shame on this company. They lie about when they will repair your stuff too, so dishonest and I hate this company.

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

My oven looks like it has never been cleaned. The self clean Aqualift does not work to clean your oven. If I would have known that this feature did not work for self cleaning I would never have purchased this oven. My old cheaper oven at least came clean on the self clean cycle. Now it seems I am going to have to scrub my self cleaning oven. What a waste of money. Will never purchase another Maytag appliance.

Below is the message I submitted to Maytag on 5/6/2016 at 10:00 a.m. ET and just received an answer via phone call today 5/9/2016 at 3:30 p.m. ET that Maytag will be doing nothing. Also, my husband has still not received a call about the drum seal and when Maytag can come fix this part that broke in their machine only months after purchase. I will let you read my message to Maytag and you may decide if you would like to buy their dryer after reading what I sent and knowing they will be doing nothing. (Washer works just fine).If this message could be passed onto customer retention and/or management, I would greatly appreciate that action being taken. My husband, and I purchased a Maytag Washer and Dryer Set from Lowes in (Listed Location) on (Listed Date) (Model Number: MGDC555DW2 and Serial Number: **). The dryers drum seal has already gone bad on one side. We had a Maytag servicer come to our home on Monday, May 2, 2016 to confirm this and said he needed to order parts and we would hear back from him on my husbands cell number in a few days, which we still have not received contact. Additionally, due to the drum seal going bad, a whole load of laundry has extreme tears in the material to the point of being ruined. I have pictures of the clothes/sheets and drum seal, however there is not a location on this contact form to upload them. I have three work shirts, worth around $30.00 each and new bed sheets just bought in the amount of $77.39 which have full threads pulled through them due to the dryer going bad in only four and a half months of normal usage. I am writing to request compensation for my items that are now unwearable/unusable and would be glad to provide pictures and receipts for price of items. We of course have not used the dryer since, which has been a huge inconvenience, especially with no update in knowing when the dryer will be fixed and reusable. Please contact me back in regards to my request. Thank you.

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

Oven failed after 2.5 years of normal use (1-2x / week). Apparently a relay failed (and burned out bake element). Contacted service & parts dept and learned that repair would cost $100 for service visit and $413 to replace the control board. Only the $80 bake element is covered by the limited warranty. Wonderful oven if your hobby is appliance repair. After 2.5 years, it now functions better as a toilet than an oven.

I have trusted Maytag for many years, more than 60 years, my parents and then myself. My Dad always told me I could trust Maytag over any other brand and that has always been true until I bought a new Centennial Econoserve Washer. This is without question the worst machine ever made. I should have asked every question in the book concerning this machine but, oh no, I just trusted the name MAYTAG. I am so sorry. I cant trust it to clean anything that shows it needs cleaning so you have to wonder what does it clean that you cant see. Im sorry people, I just dont know what to do. I cant afford to buy a new machine and the store I purchased are basically telling me, Sorry, you bought a stripped down model. Too bad! I will never buy another appliance from that store nor will I recommend them to anyone. Too bad since they are locally owned. Anyway, Maytag, you blew it badly to turn out this terrible machine. Thats my story and Im sticking to it. Better product next time.

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.

Nice refrigerator, but cheaply made. I paid 1800 with tax for my french door Maytag and expected higher durability. It operates well but one worries about breaking drawers made of such thin plastic.

It is impossible to dry clothes in the dryer without the worst wrinkles you can imagine. I have 2 of them and they are both horrible machines!! The drum spins too fast which causes the clothes to get stuck against the tumbler fins. The centrifugal force holds them there and they just ride around without tumbling in the drum. When the cycle is finished the clothes have been dryer while jammed up against the fins and they are so wrinkled you have to wash them again. The ONLY way to get them through a drying cycle without a tremendous amount of wrinkles is to stop the machine every 5-8 minutes and fluff the clothes around inside the drum by hand. DO NOT BUY!!

I purchased a Maytag refrigerator from a local business (Decker and Sons in Grand Rapids, Michigan). The fridge is a French door style with the freezer on the bottom and a water dispenser/ice maker in the left door. In the 19 months weve owned the unit weve had to have service three times. One time for the freezer door not shutting correctly, and two times because the refrigerator portion quit cooling (freezer was fine). Both times it was due to something breaking that defrosts the area behind the vegetable drawers.Both times all of our food went bad. Second time it took almost two weeks to fix (Diamond was the repair service). Now, after the service, the left door doesnt shut correctly. The quality of the unit is so questionable that I hesitate to fill it back up with food. Its just plain old junk. Luckily, we purchased a five year warranty when we purchased it...but we thought the service would be performed by the shop where we bought it, but its farmed out to other repair providers.

Low water level resulting in poor cleaning. Very poor design. Requires 2 rinses so the water savings of the wash cycle is a joke! Im very disappointed with the so-called Maytag quality. If doing very very small or handwash loads it work somewhat ok! Would never buy Maytag again!!

This washer does not distribute enough water to wash clothes properly. I continually take clothes out of washer that are not completely wet. My darker clothes have white spots of detergent on them that did not get rinsed off. This product should be pulled from the stores. We have tried everything, using deep water wash, bedding wash, to get more water in the machine. Our clothes are not coming out clean. Complete waste of our money!

Bought a new Maytag Over the stove model Microwave from Lowes. It worked fine for a while. Then it started saying open close door. We opened the door and closed it, and sometimes it would work. This went on for a while till it finally would not work at all. Called for repair, the service guy came and took it apart and one of the door switches needed adjusting. He left and it was working, good deal. 2 days later open close door started all over again. We found if we lifted the door when closing it, then it would work sometimes, until one day it would no longer work. We called for another appointment, and got a new company to fix it called ABCO. The service guy showed up and tightened a screw and it worked again, said the other service guy might have forgot to tighten it down. I tried it and it worked. We did not touch it again till next morning and back to open close door again. Called ABCO back and got a new service time for Wednesday next week. Wednesday came and went, called to see why no show. They said we were not on the service list and were very sorry. So we set up a new time for them to show the following week Tuesday between 12 and 3 pm. At 3:49 they called and said sorry, but they were not going to be able to make it today. I told her then get us tomorrow and was told they were very busy and maybe Thursday would be better. I told her we were in line and and should get service before others that came on later. Her reply was maybe Monday of next week was better. After the runaround she said they would try for Wednesday tomorrow, but no promise made. After that I called Maytag direct and they said nothing they could do except make another service appointment. She told me I could get a service appointment tomorrow Wednesday between 8 and 12am or 12 and 3pm. I asked with who this time and was told ABCO who just told me they were too busy to show up tomorrow and had put me on standby. In the meantime I paid over $300 for the Maytag microwave that is never going to need service because the Maytag service man is so lonely. And bought a $ 200 Panasonic counter model so we could have a working microwave. So now we are in over $500 and still no Maytag working microwave. They did send me a letter offering me a discount on extended service plan if I want one. I told them it would be cheaper after the one year runs out under warranty, to just junk the microwave because it has cost me way more in wasted time, waiting for the lonely Maytag repairman to show up. Bottom line do not buy a Maytag Microwave model MMV4205DS-1 unless you just want a good looking decoration over your stove with a nice light, and have plenty of time waiting for the lonely Maytag repairman.

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

The washer stopped and displayed F51. It had that growling, horrible sound like it was dying. After restarting and trying everything, including going back to Lowes to see if a serviceman could fix it, with no luck, and father reading all the reviews on the F51 error and all of the displeased customers we divided after two years on a $900.00 machine, we would tear it apart and fix it ourselves! If possible and if not, what are we losing? Nothing! What we found was clothing between the outer casing and the drum preventing it from spinning. Unfortunately, we did not know how to get to them. With a lot of effort, we got the leggings out that was causing the drum not to spin. I am sure there is a lot more socks and a pair of fairy wings that I never found after Halloween in there. If there is anyone out there who knows how to get the outer casing off of the drum, please let me know. After removing the tights, I no longer have the error code F51 and my washer now works. I just wanted everyone with F51 error code to know it goes away after removing the clothing that gets stuck between the drum and the outer plastic casing around the drum.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

Maytag Gemini - This is a double oven which I purchased in 2010. 2 days ago Apr 13, 2015, the outside glass in the bottom oven simply exploded. The oven was in use at the time. It blew the side brackets off and glass was spread into my dining room as well as a mess in the kitchen. Maytag was supposed to send repairman today. Have waited all day and finally called repair company. They knew nothing of the repair and supposedly will contact Maytag and call me tomorrow. We will see. In the meantime has anyone else had this problem?

Is there any place to give a zero to this Maytag Front Load Washing Machine Model MHW5500FW1 and if there is a class action lawsuit please include us! We have owned other Maytag Washing Machines and never experienced such an epic failure as we have with this washing machine! We were so excited when we purchased our new Maytag washer/dryer set in March of 2018 we even remodeled our pantry/laundry room to accommodate them! As the chief operator of the washing machine, I have literally cried at what a mistake weve made! We have no complaint of the Maytag dryer. Let me describe my new normal procedure for laundering a load of clothes. First, load the washer with clothes then press power/cancel then press rapid wash let the clothes get HOPEFULLY saturated with water then hit hold to start and then hit power/cancel this shuts off the washing machine. I then press power/cancel again and select normal and the water empties out of the washing machine from the prior load and then starts to refill, if the add a garment light comes on (when it wants too) and no I dont change any pre-set settings I am able to add extra water with a pitcher, if this procedure works I let the washer run its 1-hour and 48-minute cycle. If not, I have to start over again because the add garment light wouldnt come on to allow the door to unlock. After the clothes are finished I again press power/cancel then hit rapid wash put my fabric softener in the dispenser press hold to start and let it run its 36-minute cycle making sure my clothes are rinsed appropriately and not stiff because of the lack of water. I neglected to say that when Ive tried tricking the washer and think I am able to add extra water, if Ive added too much the sensing kicks in and the washing machine drains all the water out on its own and refills with the little water it allows! Which is maddening! I throw up my hands and sit down and cry!!! I have contacted Maytag/Whirlpool complaining about the lack of water and their wacky water sensor! I asked them how can you conserve water and electricity when you have to wash your clothes over and over with long wash cycles? This doesnt make sense! My white clothes are now dingy and stiff as well as the colored. Maytag says you can use powdered detergents if its HE High Efficiency powdered detergents, but thats not true. The detergent doesnt dissolve and ends up on the clothes at the end of the long wash cycle because of the lack of water! From the beginning I adjusted the amount of powdered detergent for the front load washer and have to dissolve it in hot water prior to washing and hopefully am able to add it to the clothes if the add a garment will let me! I have now resorted to extra cycles to rinse out any remaining detergent hoping my clothes will be soft and fresh smelling. I had planned to replace my old Maytag agitator washing machine with this piece of junk front loader, fortunately we kept our old washing machine as a back up!

Maytag Neptune Washer Drum Bearings have once again failed. Last time, I replace the whole drum via diy, cost was about $160 for the part. Now I see that outer drum is $500 +/-. I just may only replace the Seals & Bearings this time OR just part this thing out and buy a real machine without the Maytag name.

I purchased a Maytag Bravos washer in 2009. I have had nothing but problems. Since, it seems that this washer was never tested nor perfected but just put on the market to sell to us, the consumers, the company does not care that this washer breaks down constantly. First the pump had to be replaced, then the tub was replaced. These were nothing compared to coins falling through to get caught in the pump and cause the washer not to drain. When I bought my washer, I also purchased an extended warranty not knowing that if the washer were to breakdown to many times, Maytag would refuse to repair under the service plan that I purchased because now they are telling me that by letting the coins fall through is abuse of the washer. Really so what they are saying is accidents will not be covered, I thought thats why we purchase insurance.Thank You, Maytag. I will never buy your product again.

My fiancee and I purchased a Maytag washing machine from our local Sears. We got it home and it worked fine, but after the first month it wasnt switching over from cycle to cycle. We called Sears and they stated that they didnt provide service to the washing machines, so we would have to call Maytag. We called Maytag and they sent servicemen from B & B Appliance to our home. We were told that they needed to order a piece and would be back at another time to fix the washing machine. They came back and said it was fixed. I went to start a load of laundry the following morning and the basement flooded. The hose had become dislodged when they were working on it. To add insult to injury, the washing machine was still broken. I called Maytag to request a different service company come to our home. Maytag said that they couldnt send a different company. They also couldnt replace our still broken washing machine and they could not accept a return. At this point we are out an almost $800 for the washing machine, over $5000 (which we have submitted to insurance) for the damage to our home, and almost $600 for a WORKING washing machine that was a different brand. We will never use Maytag ever again.

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

The whole Control Panel lights are turned off for several minutes. Then they return on. Frequency? Few times per day. Reason? We dont know. No water or ice are dispensed when this happens. No water pipe is kinked, water pressure is OK, no problem with cooling system and nothing happens with food inside refrigerator or freezer. There are no mention made in trouble-shooting section of customer manual. What should we do? In spite of this, we are satisfied with the product so far, after 3 years of use.

Although this refrigerator is 10 yrs old it really performs well. I like the ice maker as it hardly ever hangs up, the freezer works great and the refrigerator part is really super in the veg drawer and the meat and cheese drawer. All in all this was a great buy.

Havent even used the range yet and the paint is peeling off of the top. I have had the repair guy out. The new top piece of the range arrived with peeling paint also. I put in a claim to have the range replaced and was told they would contact me in 24 to 48 hours. That never happened and so I called again. They said that they would call and, of course, it didnt happen. I paid $1,300 for a stove that looks horrible with the paint is peeling off of it. What kind of ** is Sears selling? Maytag is owned by Whirlpool and nobody wants to make this right.

I had the old style machine and finally it gave out and I bought an LG HE Large capacity. It was a well I can print it here but kept the machine for 5 years and gave it away. I bought a new Bravo Maytag set 5.2 with the old style agitator thinking I was going to get a great machine and NO. These new machines do not use enough water in the load sensing and clothes on top never get in the water. They come out with soap stains even with a double rinse. And no I am not using too much soap! My old machine had small medium and large load settings plus you could add more water if needed. Way better machine.The techs are trained to tell you this is how the machines work and there is nothing wrong with them. Finally an honest tech told me they are having all sorts of complaints and problems. If all you wash is bedding and dress clothes you get by but if you really have soiled clothes you have to do a lot of prep and then stop in the middle of the wash cycle and rotate your clothes manually! Total BS for 8-900 dollar machines. Do yourself a favor and buy a front load. At least the clothes will get flopped in and out of the water and hopefully rotate so they actually get clean. That is what I am going to try before I go back to the old scrub board and tub!

First of all, the hoses that came with my washer leaked and were cheap made. My husband put the hoses from my old washing machine on the Maytag. Then, I hadnt had my Maytag washing machine but about two months when I had a problem with the mixer. I had to turn the hot water connection off in order to wash in cold water. When I called the store to explain the situation and ask if they had their own serviceman, the person I talked to made me feel like a complete idiot. He said in his twenty something years of selling Maytags, he had never heard of such a thing. Anyway, when a serviceman finally came, he also had to replace another part due to a recall. Now, my washer is right at four years old and is leaking from under it. My husband checked the hoses, and they are not the problem. I bought a Maytag thinking I was buying the top of the line but I guess I was wrong. I will not buy another one nor recommend them.

I suppose I am the lucky one in that the Maytag Bravos was given to me free. I took out a perfectly good Maytag standard agitator washing machine and replaced it with this several years old unit. What a mistake! I read the other reviews and see that I share the same problems. I always get a the oL fault as soon as it goes to do the final spin. So I have to reset and try again. Also I have seen the same kind of dirt on the clothing as others report. I dont know that I will waste my time contacting anyone about the fault code. I may just put the old one back in and scrap this thing!

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

The serial number is MDB8979SBWD. Just a few months before warranty expired the buttons were being flaky. Eventually it would not start. We brought it to the dealer because they wanted $150 to come to the house. They replaced the front panel. It lasted less than a year and stopped working again. Being out of warranty and being a technician I took off the panel and saw that there was no insulation in so the humidity would build up. The wires in the ribbon wire were corroded. I looked up the price of the panel and it was $150. The dealer wanted $150. I did not want to replace it because of the possibility that was not the only problem. We paid $400 for it on sale, (a mistake I know better than to buy stuff on close outs.) FYI to get the dealer to deal with it it would cost $300! From reading these complaints this panel seems to be a real problem with this and Maytag is not supporting this LEMON. I see a lawsuit here. Too bad Maytag is only out for profit. What is disappointing is that Maytag is owned by Whirlpool. Whirlpool has or used to have good appliances. We had a microwave that lasted 15 years and our last dishwasher that lasted 15 years. We will never buy Maytag or Whirlpool again. Maytag is junk. The dishwasher is probably ok except for the panel. Shame to get rid of it for that but unless I can bypass it that is what we will have to do. $150 is too much for a gamble and it seems that panel is a problem so it probably would not last long anyway.

The salesman tried to convince me to purchase a Bosch dishwasher, but I wanted one with a fingerprint-resistant finish. That narrowed my selection to several manufacturers. This dishwasher has a food grinder in it. It gets my dishes spotlessly clean, and I have been very happy with it.

Bought a Maytag Bravos washer 21/2 years ago... already have to buy a new washer... not a Maytag!! It started with the ul message coming on. Never could do anything to get it to go off.... then started leaking water around the bottom... bearings went out... costs more to fix than buying a new washer which is what I DID. Not a Maytag.... thought Maytags were a great product. Believe me their repairmen are always busy, not just sitting around like in their commercial.... Never buy a Maytag appliance again.

I purchased the Bravos X washer approximately 13 mos ago. Washer was noisy and has deteriorated since installation. I questioned the ability of a non agitator appliance getting close clean but was assured it would. Not the best if clothes are just moving against clothes. The machine had a difficult time in between adjusting to wash balancing a 3x event upon starting. It leaked intermittently during spin cycles and stopped due to unbalanced loads, sometimes refilling and stopping again. Now it wont spin at all, circuit board problems! This is my first and last Maytag. The company will most likely not balance/compensate on the purchase price (like the Bravos X) because it is beyond the 12 mos warranty.

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

Weve had 2 Maytag washers that lasted a combined 41 years. Five years ago we purchased a Bravos XL top load washing machine directly from Whirlpool. Like many other reviews, it is impossible to keep the machine from going out of balance and trying to tear the laundry room apart. I called Maytag and of course they want to make sure the machine is level in at least 3 dimensional space as well as 2 parallel dimensions per String Theory. As far as the 3 dimensions, I assured them I had already thought of this (as an aside, ever try to find any flat metal on one of these machines? Kind of helps when using a level.)So after more exciting conversation, they offered me a Warranty for $437. While trying to control my laughter, I said I could trash the Bravos and buy a new machine for that price. As far as repairing it, it cost $120 for a repairman to grace my door step plus $35 every 15 minutes plus parts -- again, the decision is to trash it and buy a new machine. In case I was too subtle in my comments, I WILL NEVER BUY A WHIRLPOOL PRODUCT AGAIN. Im too frustrated to tell you about my KitchenAid fridge. As much as I detest it, I am forced to join the buy and trash 5 year club . Sometimes the good old days were really better.

Dual oven - one is a convection oven. Never used the bottom drawer so that was wasted on previous range. I purchased a white appliance to match my others. The white stove top is a pain. Too bad it wasnt black. I checked this model online and found a good price in the city. I contacted the local Home Depot and they did a price match less 10% - all a bonus. The ovens work great although I have not tried the self clean. I have read that similar models have problems related to the self clean feature - high heat and circuit boards. My plan is to have a fan directed at the top of the stove when I use it and the range hood fan going. The convection oven is great - hard to mess up a recipe with that. The dual ovens are truly a great feature - strongly recommend. The keep warm is great also - nice to have two things cooking at the same time. That being said - the bottom oven is low, but that is worth the extra cooking space.

One year ago I bought a Maytag Micro-wave and a Maytag dishwasher - big mistake. I should have done some homework. I had problems with the dishwasher since the day it was installed. I should have suspected something was wrong when it was delivered. I opened my front door and there stood a deliveryman holding my dishwasher in his arms. He said, Where do you want it? I couldnt believe he could be carrying it by himself, especially since it took three of us to move out the old Thermador which by the way was still working just fine after almost 30 years. But my wife insisted on a new washer for her new kitchen. The Thermador was actually made of steel. The new Maytag was made of plastic even the motor. It had some steel and copper parts but mostly plastic. I dont think it weighed forty pounds. The problems began the first day with leaks through the door and under it. I suppose eight or nine service calls happened in the next 3 months. The factory service men were different each time and each had their own guess as to what caused the leaks. Over time they replaced all the parts that could be leaking some of them twice, because subsequent servicemen discovered that a previous service man had installed the wrong parts. We often had to wait several weeks because replacement parts were not on hand, and would be ordered and shipped directly to us. Then we would have to schedule another service call, only to find out the wrong parts came - more delays. One service man told us we were using the wrong detergent, even though it was the detergent and spot-free rinse that came with it. Another service man removed the door cover so he could watch to see where it was leaking when it operated. He said the soap was foaming too much and flooding over, so we had to try another brand of soap, even though by now we had accumulated three other brands that were just barely used. The service men never did fix the problem. It took much experimentation from my wife to stop the leaks, which meant we could only use a fraction of the recommended amount soap. By now we were using so little soap that the dishes always came out dirty. So our choice was mop up a wet floor or have dirty dishes every time. Most of the time now we wash the dishes in the sink. One service man said in Maytags effort to make the dishwashers more efficient, and less expensive to build that the motor and pump were way under powered, and everything was made from petro-chemical by-products (cheap plastic) and that we should invest in the extended warranty. Its cheaper than paying service calls when the warranty runs out soon. What we should have done was exchanged it for another brand. My wife said had she only known, we would have never replaced the old Thermador which will be my next dishwasher. As for the micro-wave there are many things I dislike about it especially the rectangle glass tray which is extremely awkward to remove and replace each time you have to clean out crumbs and spills which happen often. The timer on/off bell is way too quiet with no volume control. The message and operation display is difficult to understand. And to top it off the cheap plastic handle broke one week after the warranty ran out which I found out that its less expensive to buy a whole new door than pay for parts and a service call to repair handle. Maytags track record made me not want to deal with service dept. again. I will probably be money ahead to trash the two appliances, start over and do some homework and maybe buy a European made appliance. I know German technology is not all about profit making, but quality, reliability, durability. I hate to sound un-American but greed in American corporations will be their downfall.

This washing machine has been very reliable.No repairs needed yet. This machine has stood the test of time. We use it at least.. four times a week. Light and heavy loads. It fits in our washroom and budget. Just perfect. I would recommend this brand to everyone.

I purchased a Maytag Bravos washer and dryer pair in 2009. Over those 5 years I have had at least 8 shirts come out of the washer with tears in the armpits. First I thought it was my armpits destroying the cloth. Then I thought it was cheap cotton (all my shirts are 100% cotton) from foreign manufacturers. Ive had two shirts destroyed this week, this mornings was really thick material. Usually when I remove clothes from the washer, they are entwined and twisted. Consistently when I wash any load including a towel or two, the washer becomes unbalanced. My clothes often have a foul odor after washing. My theory is that the lack of a center agitating spindle is allowing the clothes to tangle, and not really cleaning them. I have to use the extra rinse setting or the clothes come out covered with soap suds. In summary, Im not happy with this washer and will never buy another Maytag appliance. Im also not sure the high-efficiency technology has had all the kinks ironed out.

This dryer ripped a gaping hole with sharp shards of metal exposed. It was working fine, and then it made a weird noise. It stopped and I assumed my laundry was done. We go to remove clothing and cut hand open on exposed metal. As if that wasnt bad enough, several hundreds of dollars in clothing had cuts in them. This dryer worked great for years, and out of the blue this happened. Im a widowed disabled mother, and cant afford a new dryer.

We purchased a Maytag washer model MVWC400XWO almost 2 years ago and it has problems with the bearings and the whole computer board is defective. I was told to buy the extended warranty for $350, which we did. As of today, we were told by extended warranty they are refunding our money because there are so many things wrong with this washer, including the whole computer board, that it would cost them too much to fix or replace it. Im in complete shock. We paid well over $500 and are still making payments on it. I spent the day reading hundreds of reviews from people with these exact same problems and Maytag is aware of it and will not help. They should not be selling these anymore. Im completely sick to my stomach. I cant afford another washer and when I called Maytag, they said it was past the year and we are out of luck. I cant believe this can happen to people and they get away with it. A washer should last longer than 2 yrs.There are hundreds of people going through this with Maytag and no one will help.

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

I have a Maytag washing machine (MDBTT53AWW1). The total cost is $524 for machine plus installation. And the cost of yearly repair on this machine is $300.I purchased this machine a year and 10 months ago in January 2010. A few months ago, the control panel started to only light up partially but the washing machine continued to run. A few days ago, when i tried to turn on the machine, it would not work--the control panel was no longer lighting up. I called a repair man recommended by Lowes, and after explaining the problem over the phone, we scheduled a time for him to come (ten days later was his first available opening!).Ten days later with a broken washing machine and doing all the washing by hand, the repair man came late. When I made the appointment, I was told he would come anytime from 8 to 11 a.m., and of course, he did not show up until almost 1:00 pm. When he finally arrived, all he did was look at the model and determined instantly that the reason our control panel was no longer working was due to a faulty design. This dishwasher allows the steam to escape through a small vent placed to the left of the control panel. The steam inevitably causes a short circuit, meaning that this will be a reoccurring problem every year.He did not dismantle anything and was in my home for no more than 5 minutes. I was told the cost of a new control panel would be $141 plus his labor fee of $137. So all in all, if you purchase a Maytag appliance, the initial cost is irrelevant. If you purchase a Maytag appliance, you will spend almost $300 yearly to maintain it--basically the cost of a brand-new washing machine.Something needs to be done; this is unacceptable. The least Maytag could do is provide all of us, fools who believed in their product and thought that they were of quality, with a free10-year warranty for this faulty machine which is pre-determined to break down every year as a result of their poor design planning.Cost aside, what kind of world are we living in that major appliances are made to last just one year and then are to be thrown in the dump? There is no way I will pay $300 for the next ten years to maintain a product that is made to break. That is wasteful and disastrous for the environment. Shame on you, Maytag. You will be filling landfills around the country with your terrible products, and the world will be a worse place for it.

We bought this washer before Christmas. I was very excited. However my clothes don’t come out clean. I am actually washing my white uniform with hands because each time I wash, dark scums remain on my clothes. I think that the machine sensor does not sense how much clothes are in there and how much water is required. This machine is very disappointing, it needs to be recalled. See pictures below.

Purchased a Maytag Bravos top load washer and dryer in May of 2011. We had our other Maytag washer and dryer for 14 years, and they were working fine when we sold them. We saved a year for a new one. We spent $1,700.00 for them both. We assumed they would last as long as our old ones. Been buying Maytag our whole lives. Besides the clothes not getting cleaned. Besides the washer smelling, even after we clean it regularly with the product proposed. Besides it not working on the normal function. Besides it shredding our clothes if you put it on the highest spin speed. It started to make a very loud noise. Like an airplane taking off. Called a friend of ours that use to have an appliance store in Fenton, Michigan for decades. He said it was the bearings and that You have to replace the whole tub. A $300-$400 fix. And that it would do the same thing again in a short period of time. He said that they are junk.We would be better off buying a new one. He said, The ONLY one you can buy now that will last like they use to is Speed Queen. I had never heard of them. They start at about $750. But they are worth it. He said that they dont make any washers to last more than 3-4 years anymore. We will NEVER buy Maytag again. And Sears wouldnt give us the time of day. Each time we called and asked to be switched over to the recall department, we just got a busy signal, then a fax machine noise. We have shopped at Sears for years. Boy, loyalty doesnt mean anything in this day and age. Im sure Speed Queen will be happy to help us out. DO NOT buy any Maytag products. There should be a class action suit against them for this. There are thousands of us that got ripped off. I cant tell you how upset my husband and I are about this. We are retired, and on a fixed income, and I am disabled. The stress this has caused cannot be put into words.

I have owned this Maytag washer model # MVWC360AW0 since Dec/2013. I do not have a single complaint about this machine. It has worked flawlessly for 5 years and am very happy with it. I just follow common sense maintenance like cleaning it once every month (do a full cycle with just borax & baking soda 1/2 cup each) no clothes of course. Another thing I do is to leave it open after I am done washing so it dries completely before I close the lid. The washer looks and works like new, cant be happier...

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

Nobody seems to know how to replace this part online. I have discovered what a POS this Maytag MGDC700VWO dryer is. The ONLY way to access this part is to beat an access hole in the bottom-left panel. After the repair, you are left with a nice 4 hole??? What an absolute POS! The back panel has screws but after removing them, I discovered the panel is also tack-welded! This is beyond stupid! Maytag used to be a great product before they were obviously sold to the Yugo factory. Time to move on.

This microwave doesnt rotate in use, it only goes back and forth...not as good! I believe the rotating type of microwaves heat your food more evenly, but it might just be a personal preference. I would NOT recommend this type of microwave.

I purchased a Maytag (as Maytag was always rated the Best) and from the start was not happy with the product. I contacted Maytag (Whirlpool, the makers of Maytag) and was told to get stains out, you had to pre-soak and scrub the area... really? Then I might as well just hand wash all of my clothes and hang to dry. I would not need a washer. My clothes do not come clean at all. DO NOT PURCHASE A MAYTAG (or I think any washer Whirlpool makes as they do not back their products).Prior to this, I had a Whirlpool washer with agitator and loved the washer. Clothes were always clean, and I did not have to pre-soak stains for them to come clean. Go Figure! I have never been so disappointed in a washer or company. I am now looking to purchase a new washer as I have had it with this one... and it wont be a product made by Whirlpool.

I can honestly say that my Maytag refrigerator is indeed the worse appliance that I have ever purchased. This is how it rolled... I bought a new Maytag stove, frig, microwave, and dishwasher in June of 2006. Here is what I am now dealing with... the frig went on the fritz 2 years ago (warranty expired). The problem being the freezer would not automatically defrost. Because of this the coils would ice up and this prevented the cold air from moving from the freezer into the frig part. Things remained frozen in the freezer, but everything became warm on the other side, the frig side. I had it repaired about a year and a half ago to the tune of $165. Then about 6 months ago the problem reoccurred, but instead of paying for another repair I figured out that if I used my blow dryer I could defrost the ice from the coils on my own.Unfortunately, the problem reoccurs more frequently now and I have to manually defrost the coils almost every week. This past weekend things finally came to an end as no matter how many times I manually defrosted the coils, it would be fully iced up again with an hour or so. Also, all the time it is acting up it just sucks up electricity, and I have notice a spike upwards on my energy bill. It must be related to the frig. So, I bit the bullet and bought a used frig on craigslist just to hold me over until I have time to do research on what appliance brand is indeed reliable. I should of done this before I bought my Maytag appliances from Home Depot. As far as my other Maytag appliances, here is their current condition. Microwave about the stove: the handle broke off a little less than 2 years after purchase. Stove: now has rust on the front of stove, at the bottom of the stove which is a pull out drawer.Dishwasher: not working at all. The start button doesnt work. Normally, you just push the button and a green light comes on and it begins the first cycle. This is no longer happening and no green light comes on. Refrigerator: Took it to the dumps this morning to be recycled. Cant believe it, all of these appliances are nothing but crap and I will never purchase another Maytag. I have shared my experiences with all my family and friends and have encouraged them to avoid Maytag, as it is not even close to being the product it used to be. Another piece of junk coming from somewhere other than here in the USA. We lose jobs here in the US, and then end up buying the goods from another country that makes inferior products. How stupid can we get!

Ive always loved Maytag but this centennial makes grinding noise and doesnt wash clothes well. Even on largest setting the drum never fills all the way up with water. It adds water 8 times during wash cycle only to immediately go to drain after last add. Ive only had for approx 4 years and the 10yr warranty only covers motor and basket so be sure to understand your warranties.

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

I purchased a Maytag top-load washer 16 months ago. I had a problem with it four months after purchase and they told me it was not leveled, which I did not believe. I set it up as the manual said to. The washer left clothes soaking wet about every 30 loads. I continued to use it and the washer finally quit working after 16 months. The repairman found the nut which holds the pulley on the shaft that turns the drum had been loose and had been this way for some time. $129.00 later, it was fixed. It works fine now. I wonder if this problem should have been caught on the first service call when it was still under warranty.

We purchased a Maytag brand thinking it would be a quality long lasting machine. Wrong, the washer shakes from day one, We complained to Lowes, they brought out and installed a second unit, it does the same. The clothes dont get clean, sometimes you can see the blue HE Tide still on the clothes (sheets) after cycle is complete. Junk, waste of money, Ill never buy another Maytag product again. Dont waste your money on a Bravos Maytag top loading HE machine.

When I went to use this machine (maytag bravos). I noticed there was like a 1/4 filled in tub, checked water flow, that was fine. Then read the manual that Maytag sees using Less Water is better for clothes, I always thought it was less detergent, ohh well. Wouldnt recommend this item to anyone.

We purchased our Maytag® 4.5 cu.ft. White Front-Load Steam Washer online through Menards and picked up the washer on Feb. 5, 2022. We set it up on Feb. 6, 2022 and it didnt work properly from day one. The washer makes a clicking sound when it spins and also gets out of balance very easily. I contacted Maytag and they referred a warranty repairman in our area. He looked at the machine and said it could be one of two things and it would be a major repair. We would have to haul the washer to his shop and he would have to tear apart the washer to fix. He said it would be a big job to fix and we would be out of a washer for a few days.I also had contacted Menards shortly after we purchased the machine and they told us to contact Maytag. They wanted nothing to do with us and didnt want to stand behind a product that they had sold. Getting major warranty work done on a NEW washer makes no sense to me. I am very disappointed in Maytag and will never purchase anything Maytag again. Dont bother wasting your money like we did!

So our 4 year old Maytag Dishwasher just took a crap. Thank God we were at the kitchen table when it started to smoke, which smelt like burning wires and unplugged it immediately. Repairman came out and said it would be a 3 to 4 hundred dollar repair. What happened to the great 10 year Warranty? Oh yeah, its a limited warranty which does not include wiring. Could have burnt down my 4 year old home, but thats ok, not covered. The good news, the upper arm I replaced due to wear and tear would have been a free repair, because it would have been covered! No more Maytags in this home, ever!!

My husband and I just purchased on 4/8/17 a BRAND NEW MAYTAG 4.3 CUBIC FEET CAPACITY FRONT LOADING WASHER WITH STEAM AFTER OUR PREVIOUS 15 year old washer that we both used just finally started having issues. So we decided to go new and with front loader with good brand. How sadly I was wrong! We brought our washer home, hooked it up and turned it on with 1/2 load of tiny laundry. It didnt even make it through one load! This POS started throwing error codes E1, E2, F8, F9, Suds and wouldnt drain any water. We reviewed the manual again, checked the filter hoses and detergent. All was fine but washer wouldnt work! I called Maytag 2 days later on Monday and after repairman came to look at it Thursday said it needs new drain pump and today now power wont turn on and nothing will work on front of machine, mind you this machine is brand new! I am so disgusted and angry that any company would sell this quality to anybody and at the prices they charge! NEVER AGAIN WILL I PURCHASE ANOTHER MAYTAG!

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.

I have owned my Maytag Bravo Series less than a year. After 4 repair calls, I called again. The service department was rude and hung up on me. He accused me of destroying the washer on purpose. They are the worst company I have ever dealt with. DO NOT BUY Maytag products ever.

Bought this machine with the intention of having at LEAST 10 problem free years with it. Its a Maytag after all. Not an unreasonable expectation. Within the first 2 years, the machine sounded like the bearings were going out (heavy, grinding noises when it shifted gears). Repairman came, replaced the entire drum (only way to get to the gears, I guess). Didnt fix a thing. Then the rinse and spin cycle on ANY wash cycle randomly quits. Just stops. Full load of wet, soapy clothes, sitting in the tub while an LD error code quietly flashes.Its not uncommon for it to take two full days of screwing around with this machine to get one load of clothes done. Have to UNPLUG the machine, let it sit for about an hour, and try again. It is the biggest waste of money ever and I will NEVER buy another Maytag nothing. Contacted Maytag and they recommended I call a repairman...REALLY? REALLY? Gee, I wish I had thought of that. Repair guy has been to my house so damn many times for this machine, we are now friends on Facebook. Dont waste your money on this machine.

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

The dishwasher doesnt clean and the dishes and silverware come out greasy. What a piece of crap.

If you have a second floor laundry room, DO NOT, and I repeat, DO NOT acquire this washing machine!!! The Bravo MCT model washer is TOO loud (during spinning cycle), and for some reason, the clothes come out all tangled up. Some cycles are a waste of a cycle, and most cycles take a bit longer than my former washer. I miss the cycle choices I used to have on my former GE Profile washer (GE does not make that model anymore hence my changing brands). For the most part, clothes come out clean; thats why I give it a two-star rating instead of one. The dryer: Must dry every load in low heat so it doesnt come out extra crispy and wrinkled up. Although I generally have to run a second drying cycle, low heat does work great and the clothes come out ready to be folded/put away.

Purchased a Maytag - MDB7749AWM1 dishwasher in 2011 from Home Depot. The door seal has failed several times and been replaced by a serviceman. The warranty has since run out but the seal continues to fall out every time you run the dishwasher and open the door. Has anyone else had a similar problem? I have considered gluing the seal in place but cant find a glue that will handle the temperature. Im sure that Maytag will say they have never seen this problem before. Maytag is off my purchase list forever!!!

The glass shelves stop 2 1/2 inches from the back of the refrigerator. Things keep falling down in back. I have a counter depth. Cant afford to lose any space. Freezer poorly designed for space compared to one I had before.

#Mgt8885x500 Maytag Gemini. After oven heats up, racks fall. What should I do. This is a safety issue. Help, afraid to use oven.

Purchased this machine to replace the recalled Samsung washer that was exploding. I should have kept my Samsung. I loved it and had no complaints, but since there were reports of it exploding I took the rebate and purchased the Maytag Bravo Nightmare. Everything you have read or will read here is true. I would spend hours, I mean hours trying to do a load of laundry. If the cycle would complete itself, the clothes would be soaking wet, and they never smelled clean. I would try rinsing again and the cycle would start out with 18 minutes and I would return to the machine 1 hour later and it would be still running water and still have 18 minutes or more left. I watched it complete the spin cycle and start the rinse cycle again. We had the service guy out several times - he would call the techs and they would test the machine and say nothing was wrong other than it was off balance. They said I was using the wrong detergent - when proving that I was using an HE detergent, they counseled me on how to lay the laundry into the machine, and said I was using too much laundry detergent. After babysitting this machine for more than a year, and being told by Lowes Customer Service that the techs say there is nothing wrong with the it, I was fed up. I called Lowes and told them to send their techs to my house to do the laundry. I threatened to call for service every week until my extended warranty was exhausted. They finally gave me a merchandise card valued worth the purchase of the machine. Now, I have the painful decision of deciding what to buy next - It wont be a Maytag!

Its frustrating the way the bottom of the dishwasher has curves making wasted space. Second, the tracks for the trays are such that often the tray comes off the track and makes it difficult to get back on without unloading dirty dishes to do so. Finally, I really dont get the lighting system for dishwashing on the outside of the machine.

They are coming for the 7th time to fix the ice maker. Three full replacements. The bottom of the freezer had a buildup of ice, another call to repair. I know where the Maytag repairman is, hes at my house.

I wanted a small stove that did what a large/standard stove could do. I was worried that the heat would be weak but it cooks my food amazingly well. This stove has all the bling of a simple stove for a smaller price and size for my tiny house.

Maytag AquaLift Oven #YMER8880BW - The aqualift technology does not clean the oven. It is sorely inadequate. I bought Maytag because of its reputation. This range should be recalled as should all their ranges with this useless technology. Buyers BEWARE! Do not purchase any range from Maytag which advertises Aqua Lift technology. This purchase has soured your reputation Maytag. I also purchased a fridge with the stove. I will NEVER buy a Maytag product again. I also would like to ask frustrated and disenchanted readers how they are getting their ovens cleaned. What product(s) can be used. Maytag - complete FAIL!!

Purchased a Maytag dishwasher (Model #MDB7749SAW1) in January of 2013, installed in February. A little over a year later the control panel went out. I called Maytag and they were kind enough to pay for the part and I had to pay for the service. Now it is July of 2015 and the control panel is going out again. I called Maytag directly and talked with a service representative and the best they could do for me was for $269.95 they would have it fixed and I would have a one year warranty as well. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 2 1/2 years it is becoming a very expensive dishwasher. There should be a recall on this control panel. Very disappointed.

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

We have a Maytag Dishwasher Model MDBH949AWB. We have purchased the extended warranty. Today, after more than 100 minutes on the phone, mostly on hold, we were unable to schedule an appointment to replace the control board, or even have them verify that we have extended warranty coverage. It generally took many many minutes to get a person, only to be referred to a different person at a different number. Nobody had access to our extended warranty info, and to go further into getting a repair scheduled, they said they needed that info. I finally went on their website, and after keying in extensive information, I got a screen saying they were having trouble with their website, and to please try again later. So I did their chat, and ultimately they told me to call 866-730-6094. The earlier numbers I called, in sequence, were 866-576-1660 (53 minutes on hold); then told to call 866-265-0029, for another long hold. And then told to call 800-626-4342. Long hold, and I hung up. At one point, I think the second person I actually spoke with gave me an incident number of **. My extended warranty expires in Feb. of 2017, and they even asked me to renew early. Since the warranty seems totally worthless, why would I do that? Terrible customer service. Wont do business with Maytag ever again, and am warning others not do so either.

I hate my new Maytag washer and wish I had never purchased it. Theres no way to control the water level in it, and on sensor mode, the clothes are barely wet and rubbing against each other creating wear. Things come out with soap stains and twisted up so tight that I dont believe water got close enough to the dirt to carry it away. Dont waste your money.

Nineteen-month-old dishwasher was repaired once while under warranty; 6 months later, same problem. They said they would send me a new part but I would pay for labor. I wasn’t happy but I agreed. I am being forced to use their people and pay first before the part is received and before the work is done. They said this is their procedure. If I must pay labor, I should be allowed to use whom I want. It is absurd asking for payment before job is done when the part is free. I have since checked the complaints, and there are over 200, with one woman on her fourth control panel – I will be on my second one. I feel this machine should be replaced free of charge. Its obviously a lemon!

My Maytag Front Load Washer Model MHWE200XW purchased from Sears had a malfunctioning spin cycle. The authorized Maytag repairman from Landers, with support from a Maytag technician by phone, did not know how to repair it. The machine had light use over the past 15 months, and hence was not covered under warranty. So I am out $650 for the machine and $200 for the repair that resulted in continued and even worse malfunctioning. Unfortunately for me, the tests did not show any errors and the machine did not state any error. It just would not spin and then would not allow the door to open. It is a lemon and I do not recommend its purchase.

We bought this refrigerator in 1998 and it is still going strong. It has gotten a bit noisy over the years when defrosting, but it works great. It is not as fancy as the freezer over top, but it is large and so is the refrigerator.

What junk. Bought this gx2shbxvy05 french door fridge. In less than 16 months the freezer is fine the fridge section gets up to 80f. Throw all the food away. Found the freezer coil covered in ice. Took the back panel off and noticed ice around the copper tubes by the compressor going up into the body. Not good. Put a small brick heater in and slowly melted the ice into the drip tray. Warning, it filled up 4 cups of water and of course spilled and killed the wood floor. After the clean up. Plugged the unit in and it seemed to work for about 3 months. Now its dead again. Looked into parts around 300 to 400 bucks plus labor to replace the system needed parts. P.S. the fridge, this junk replaced is downstairs working after 25 years not one issue other than the color. NEVER BUY A MAYTAG product please. TRAIL APPLIANCE should never have sold this product and should have stepped up to help out. Wont buy from them again.

My dishwasher is less than 2 years old - has only been used a total of less than 12 months as I am seasonal in Florida. The control panel has failed. It will cost $275 parts and labor to fix.

Maytag refrigerator - After 3 months, a water line broke and caused $350 in damages to our kitchen floor. The next month, the ice maker jammed. The next month, the ice maker went out. I have agreed to let the Maytag repairman (youve seen the commercial where he never has anything to do) use our spare bedroom. Seriously its the worst appliance, by far, Ive ever owned and Ive had plenty as I am 71 years old.

I purchased the subject Maytag washer (MHWE201YW-3.5 CU FT WHT FRNT LD WSHR) from Home Depot in December of 2012. I got exactly 1 year of use and then the washer stopped working. I called the Home Depot repair person who came and repaired the unit. The repair lasted two weeks and the washer stopped working again. Because the unit was no longer under its 1-yr warranty the Home Depot repair person was not available for repair. Another independent Maytag repair person came and evaluated to problem. He said the computer which is located on the motor was no good and to the tune of over $400.00 (parts and labor) a new motor was purchased and installed. It lasted two months and it quit working again. After several months I was finally able to contact the original Home Depot repair person for one visit. He said he would check the code message and get back to me. I never heard from him again. I have been taking my laundry to the laundromat ever since and it is getting expensive. I dont want to spend another $400 on this machine as it will only break again. What do you recommend?

I would like Maytag to repair or replace this dishwasher. It has only been installed since November 2014. The only button that works is the auto clean. None of the buttons work. I thought Maytag was a reputable business.

I have owned a Maytag gas dryer for 10 years now. I have had to replace the idler and belt 4 times now. This dryer appears to be built as cheaply as humanly possible just to get it past its almost non existent warranty. The replacement parts are even worse. The idler has a bronze bearing in it as a wear item. Really??? Why was this never even considered as a part that could be lubricated at least occasionally?Granted, lots of people do not have any mechanical ability at all and just pay through the nose for a repairman to come to their place for any repair then pay dearly for the service but, I DO have mechanical ability so I do all the work myself. That is why I know firsthand about the terrible manufacturing results and the very cheaply built replacement parts available at outrageous prices.

All of a sudden, the lid lock light is flashing. The washer is only 1.5 years old!

Maytag has always been my choice with appliances. Ive purchased others and always dissatisfied. This dishwasher has been a trooper and lasted forever. Its been overworked with 4+ children and yet still going strong. I recommend Maytag????

July 2018 I bought a new Maytag electric washer and dryer. After one mo. the enamel inside the dryer started come off in sheets. It was replaced with 2019 model which after 3 mos. wont come on unless you unplug it and plug it back in after using it. I am now waiting for Maytag to send a repairman to come look at it. Steer clear of Maytag front load electric dryers.

The washer does not wash properly at all. There is not enough water. The clothes come out covered in lint and still soiled. MOD: MVWX655DWI, SER: C63142093. DO NOT PURCHASE THIS PRODUCT unless you want a ton of frustration!

I purchased my new refrigerator in 2005. Within 3 months, the bottom freezer went out. I had purchased warranty and it was fixed. Again, the fan went out 1 year later with the same exact problem. Now, it went out again 2 years later with the same exact problem. I called Maytag and they do not care. They are rude and simply will not fix this refrigerator. The warranty is gone and again, I have to pay for this constant problem. Why doesnt Maytag own up and service this problem. Didnt we pay for this? It wasnt given to us free. Someone needs to step up and gets it resolved for consumers. If legal action needs to bring this to their ignorance, so be it. We all have spent a great deal of money on a refrigerator and all they do is say, is “Too bad. How can any company continue to be in business and operate this way?