My Daughter got me a Maytag oven with the AquaLift technology and is a piece of Junk. Half the time the Water is still there when the cycle is over. The water has made it between the front glass pieces and the finish on the top of the stove looks horrible, it just looks dirty. The knobs are cheap and the fake chrome finish is flaking off. Unfortunately Im stuck with it because I cant afford a new one... this was a gift to me because Im disabled and it was to make my life easier.

Our washer stinks. We have done all the things suggested by Maytag, and it still stinks. Maytag suggested having it serviced by A&E, but I see on the Internet that they are probably not the best choice (very bad reviews). We called our local Maytag dealer, and they said that there is no fix available. They just stink. We will buy a new washer and will never buy anything Maytag again. I would suggest the same to everyone else.

My disappointment with this washer (Bravos xl) is that it smells moldy and musty no matter what I do. I clean with affresh when light comes on, leave the top open, etc. I have tried cleaning it with baking soda and vinegar poured down the detergent opening. Water does not drain from the bleach or softener openings. I have resorted to using baking soda in every single wash and adding an extra rinse to keep my clothes from smelling. The laundry room always smells. I would go back to an agitator in a heart beat if this hadnt been so expensive. DO NOT BUY THIS MACHINE.

A contractor purchased the Maytag MDB7609AWW2 dishwasher about two years ago. Sometimes it will start a load, but most times it will not. The light for high temp, heated dry and sanitize work, but the heavy, normal, light indicators will not light up. Im faced with either replacing the control board or control electronics. I was told Maytag is a quality product. I have not abused the product. The last dishwasher that I had lasted 10 years. I only purchased this one because of a remodel. I will most likely replace the control board since thats the defective part. It doesnt give me a good feeling about replacing the part since it’s obviously a defective part. I will consult Consumer Reports before purchasing another dishwasher.

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

After writing a polite but stern complaint to several of the executives at Maytag and Whirlpool we got a call from their executive assistant. She arranged to have a technician come out to our house and assess the installation. He found nothing wrong and Maytag replaced the control panel for free. The technician has seen numerous faulty electronic control panels, and not just with Maytag. He would not recommend a preferred make or model. He longed for the old mechanical timer switches, which we could no longer find in the newer models. With enough customer complaints maybe they will do something about the electronic control panel in the future.

My husband and I bought a set of Maytag appliance 12/2011 the washer squeaks real bad on spin cycle and now today the dryer started making real real bad squeak sounds to the point I can not use it!!! My appliances are only 4 years old!!! And we wash clothes once a week for just my husband and I. I would not recommend buying any Maytag appliances!!! They are supposed to be the best but are not worth **!!! And I called Maytag, they are not willing to help. Bad service!!!

Washer was purchased at Lowes under direction from staff... Great washer, environmentally better, less water consumption... Well washer is piece of crap. Activator is out, door stays locked, have to unplug to release every time used, water does not drain and cycles do not function or start. Lowes no longer carries product and all other review on spot as to cost to repair... Piece of crap, loss of $600.00+. Could be used as target practice, best case scenario.

Maytag Bravos washer and dryer both need replaced in 3.5 years! Control board had to be replaced on washer in under 2 years and now the replacement went bad in about 15 months. Maytag can’t help! Hundreds of dollars wasted. Dryer is not much better as the control board is now malfunctioning! DO NOT PURCHASE MAYTAG!

Internet stated refrigerators should last a minimum of 13 yrs and up. Mine is less than 5 yrs. old, a Maytag 25 cu. ft. French Door Bottom Mount Ref. with freezer on the bottom (MFF2558VEW). Had to replace upper gasket in less than 1 yr. of purchase and needs another now (not affecting the sealing aspect on doors, more aesthetic on upper door thin flap that tears easily).Drain plug & configuration for drain was a known manufacturers defect, but cost me money to replace as 3 yr. extended warranty expired. Lower gasket had to be replaced in yr. 4 of ownership, bottom of freezer was producing a sheet of ice that needed removal every week. Normal settings is #3 for both top and bottom, worked fine for 4 yrs at this setting.Last month irregular cooling started to occur- top down to 52 degrees and bottom freezer below -20 degrees - ice cream hard as rock, have to defrost each time in microwave. Maytag repairman said could find nothing wrong, but try emptying entire contents and unplug for 24 hrs. I could hear pieces of ice melting and dropping throughout the evening. Next morning towels I had put around frig were saturated with water. Restarted frig after 24 hrs. and was working fine for 5 wks.This week same exact problem returned so I did the same thing only this time I had to go out and buy a small chest freezer as I had a full one in my Maytag and no place to put frozen food. It is nearing 24 hrs. and no water has appeared on the floor nor did I hear any ice melting and dropping - so dont know what to do. Will call repair man again and see what he suggests. As soon as I can afford another $1400 frig (this was on sale for $1,002 after discounts, but I will buy a less expensive one this time) I will purchase another brand with NO French doors and no bottom freezer. I loved my frig the first 3 yrs. under warranty, but now causing me too much physical problems having to empty and restock frig for repairs. I have a Tappan Frigidaire in the garage that is from 1998 - I bought from a neighbor who was moving and it has been working fine for 16 yrs. with no repairs. They dont make them like they used to!

Purchased a Maytag refrigerator in July 2011. The compressor failed May of 2013. After many phone calls to Maytag they replaced the parts (compressor) - my cost for labor (aprox $300.00). 30 days later, the service company had to repair a leak and recharge the system. March of 2015 the compressor failed again. Have spoken to Maytag (case # **) - they will provide no help what so ever. I was told I should have purchased an extended warranty.

Bravos MCT - I researched online and bought the highest rated machine that had the features I wanted. I like the top loading and the less water used. It cleans well but I would like more control like water temperature for example. I have had this washer about a year. I also want quiet but did not get it in this washer. That is tough cause you dont know until you have it! I think that it is hard to buy big appliances and be happy with them at my age because at 70 years old you remember when a washing machine was built to last a lifetime! Now they last maybe five years and they cost as much or more! I am not interested in lots of the bells and whistles. I just want a washer that will last and does its job. Mine has a glass door in the top so you can watch your wash (I guess..). Well, who wants to stand around and watch your wash...get a life!!! Also, it fogs up right away so you couldnt see it if you wanted to. It all seems pretty silly to me but I guess that is the way the world works today. So I go with it and I watch my wash.

My Maytag has been out of service more than in service and this is my 2nd one in 2 years. They replaced my first one due to breaking down several times. I have spent so much $$ at the laundromat after paying big bucks for a washer.

I purchased a Bravo washer and dryer set about a 2 1/2 years ago and had problems from the start. The dryer control panel went out the first day. No problem, they replace the panel. The washer is a different story. The agitator went out next and the wait time to repair it - 3 WEEKS. The agitator went out again for the second time and the tech stated that it had to be replace. Wait for it. Waiting time - 1 month including parts. To make this story short the agitator will go out every 4 months and the tech stated once its been replace it will work like a new washer. Wait for it. The agitator has been going out ever since and the wait time average 3 WEEKS. Wait for it. This Maytag is trash.

1st service call about 2 years after we got it. Put around $200 in it. Now broke down again. Service tech quoted $475.00 to fix it. So it was basically totaled after around 6 years. Nightmare kept getting LD (long drain) code. After hours of research I finally called service. Would not drain so I had to wring out a whole load of laundry and bail out the water by hand. Miserable experience!

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

IT A GOOD DISHWASHER, BUT I HAVE HAD 2 PROBLEMS WITH THE CONTROLS AND HAD THE CONTROL PANEL REPLACED. TWICE. The insurance I bought with the machine, sent me a jerk to fix it, I complained and they sent a good repairman.

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

I am extremely dissatisfied with the Maytag Gas stove and oven. The setting are too high and you cannot simmer something, it burns. I tried the oven cleaner and my oven is still dirty. The burner knobs do not have a click feature. I came home to a house filled with gas. I was not using the top burners, so I must have brushed up against the burner knob while using the oven. I was only gone an hour, imagine if I had been gone longer and walked in the door and created a spark on the rug.

I too had to replace the control panel on my Maytag dishwasher which I purchased in 2007. I was told by my repairman to contact Maytag to see if they would do anything for me. When I called Maytag, I asked them if there were any issues with the control panels as I had heard there have been multiple issues with them needing to be replaced. I was told they had no record of any complaints and offered to sell me an extended warranty for $269, but there was nothing else they could do for me. I ultimately had my repairman order the part and it was replaced. My repairman did say Maytag did upgrade the panel because of all the issues they were having with the panel. Hopefully, they have fixed the problem and it will not have to be replaced again. But if it does, I will not replace it again. I will look into a new dishwasher and definitely not a Maytag. Yes, I would be interested in joining a class action suit.

Both work good. Washer could be a little lower and it has quit rinsing and I cannot use it. But it is 9 years old, I think for their age they were a good buy. I plan to get the washer repaired because have been satisfied with how clean it gets my clothes and it washes pretty quick. I got the large capacity and with a very large load the washer gets them clean. The dryer is very good. It is just as good on a large load as small, dries quick. I would buy this type washer and dryer again and would definitely recommend it to folks. I have been very happy with this washer and dryer. The paint is coming off the washer where you put detergent and fabric softener in and it has rusted out some but it is getting a little age on it so this is expected. I like it, I can throw my comforter in and it gets it clean and the large loads always come out great. I think anyone who bought the set would be very happy with it. It is also quiet which I like.

Less than 2 yrs old and starts giving UL error on spin cycle. I try replacing the springs. No relief. Notice dark brown fluid under dryer. Thing sound like a plane taking off. A little more research and Im thinking its the bearings. Looks like an expensive repair, now I have to decide whether to cut my losses. Seriously? The reviews on here are just horrible, not like this was an dl hell machine.

Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for 2.5 years. The unit started beeping at random times for about a week - then went dead! Sounds like other reported failures and it is unlikely repairs will be permanent! Never again Maytag.

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

My only issue is that I am short and find it difficult to reach the wet clothes to put them in the dryer. Other than that I am quite happy with the machine. I have had no problems to date. Thank you.

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

I bought a Maytag Top Loader. I soon discovered that it is not possible to do a cold water wash. After much communication with Maytag Customer Service it was determined that there is no way to bypass it. And it uses a lot of hot water, even on a cold wash. Their explanation was that the water needed to be a certain temperature to make the detergent work effectively. The same detergent that I’ve been using for 40 years with cold water in my Speed Queen. When I need to do a cold water wash, I go to my parents home and use their washer. Disappointing purchase, my last Maytag, for sure.

Never buy from Maytag. I and my daughter bought from them two refrigerators of them. After one month my daughter started to fix. I am started after one year or it is leaking. Our freezer destroyed and realize this after one day all my food I throw away. The same was with my daughter refrigerator. My daughter have old refrigerator it is working without problem for 50 year never fixed. Never ever buy from them anything. It is good I was at home. Sometimes I am traveling if it happens this time. I do not want to think about this. For fixing you have to pay lot of money. I hate that I purchased something with them.

I purchased a Maytag refrigerator in November 2016. It is now the first week of June 2017 and the ice dispenser no longer works and the door alarm goes off incessantly and intermittently all day and all night. I am so sick of being woken up by the alarm in the middle of the night. I reread the manual and ran through the limited troubleshooting to no avail. I called customer service, sat on hold for a half hour, and scheduled a service call. As an interim stopgap for the pull-my-hair-out alarm issue, the operator suggested I disconnect some wires, as there is no off button for the door alarm. I wasnt dumb enough to do that and void my warranty. Best part of the call was when the operator offered to sell me an extended warranty. Well see how the service appointment goes, but I have a feeling this is the last Maytag product I will ever get. I am very curious about the lack of product recall as my research unveiled hundreds of complaints about the exact same issues I am having. Why does it seem to take a class action lawsuit before a company fulfills the promises in their advertising? Model number: MFI2570FEZ01 Purchased from Home Depot in Nov 2016 for $1,230.

We purchased a Bravo HE washer about a year ago after our old Maytag finally died after 17 years. Our new one is more quiet, does a good job with less water although the cycle times are a bit longer.

Thinking it would be dependable and clean my clothes well, I spent $888 online for this washer. Normal use, HE detergent, only adults washing normal loads. After 4 mos., would not agitate, made loud clicking noise, filled and drained. Bought 3yr service plan, and company assigned still tried to charge a fee just to look at it. After 1 week of dirty clothes piling up, bought a Samsung combo, & had the Maytag hauled away. Money on the Maytag down the Toilet! Never again--Maytag, Amana, Whirlpool, etc. All made by same folks and pure trash!

Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

I purchased a Maytag commercial residential washer in late 2018, supposed to have a warranty for at least 5 years. We are in California and I was told that there was only one facility that could come two weeks later. I removed the front panel to have it ready for service tech, who on the first visit kept saying he did not know what the problem was, and left telling me he would order parts. After Christmas, I could not get in touch with service so again called Maytag. Service was supposed to come out on the 30th.After waiting almost 3 hours, he called to tell me he did not have the parts. Also, this repair tech treated me very bad since I removed the front panel which I thought I was being nice. He called me back on the 30th, said someone gave him a part, and came. All he did was remove control panel, lost the start button and told me it worked without checking it at all. He was rushing to another appointment so I tried to start it and it still had the original issue, which was slow agitator and a rubbing/grinding sound. Now, after he did something with control panel it had a clicking sound. I immediately called corporate and was told when he came back, which has now been over a month with no washer, that he would be with a senior technician.January 5th I waited all afternoon and he called and said he was not coming and that my whole washer would have to be rebuilt. He never replaced the parts on previous invoices I received, and I filed a complaint with the BBB. Now they are completely lying. Technician trying to say I had the control panel apart which is not true, and does not match up with the invoices I received. They are telling me my warranty is voided! Its been a month and a half. I was treated rudely from the beginning and now I am obviously being retaliated against. I have 3 kids, two with severe medical problems and have put so many hours into calling with all these issues.I had another service place come out and he removed the agitator and the transmission shaft/drive motor is rusted out, as well as the parts he said he replaced are worn and definitely not new. For this company to come back after all this time and say I did this, when I have the original invoice that clearly states otherwise is absolutely the worst service ever.I bought this machine thinking it would last, and now have to deal with all this. I have nerve damage and it is very difficult to take all the laundry for a family of 5 to do at laundromat. They refused to send someone else out, where they could easily have seen this repair tech never did what he said, and was unable to diagnose and fix the issue. Its appalling to me that this is how they treat customers. Laura ** at corporate is the one saying warranty is voided. The machine looks brand new as it has always been taken care of. They should be ashamed of themselves. Apparently, this is the standard a lot of times with people trying to get things serviced under a Manufacturer warranty!

I bought my Bravos XL 3 years ago after having older model Maytags since the 1980s. My mother also runs a laundromat and SWEARS by Maytag. To say Im disappointed in this purchase is an understatement!!! They have never washed the same as the older models. They twist the clothes horribly! Now Im having issues with all of my dark clothes getting grease spots on them with no apparent cause. I use HE detergent and softener (recommended amounts only) and clean the washer religiously, including the detergent, bleach and softener cups. I DETEST these machines. Also, the dryer never dries unless I run it for 2 cycles, regardless of what setting it is on. Waste of money and definitely not energy efficient when it comes to my water and electric bill, nor time efficient for me since clothes either come out still dirty or with new stains. After this purchase, I would NEVER buy Maytag again!!!!!!

My Maytag dishwasher MDB7749SAM is not quite 5 years old. At the end of December 2016 a bubble appeared on my vinyl floor. The plumber could not find any broken pipes or reason for any moisture to have gotten under the flooring. A flooring company did not know what was causing the bubble, moisture or the vinyl glue had failed. The floor got worse and worse, more bubbles.Called the flooring company again. Raised the register cover and could see all the moisture under the vinyl and underlayment. Plumber discovered the dishwasher fill valve had failed but because there was so much insulation on the kick plate, at the bottom of the dishwasher, it forced the water, which was in a pan under the dishwasher, to push the water to the back by the wall and under the flooring. Plumber said, the insulation acted like a dam to keep the water from showing in the front of the dishwasher. The first and subsequent bubbles, in vinyl were 3 feet away from the dishwasher. No way to tell the dishwasher had the problem. Has anyone experienced this problem? If not, take care to remove the kickplate and check your dishwasher for water problems.

Just passed warranty period and Maytag dishwasher broke. It would not start. Called and was allowed to purchase extended warranty for $135.00. A new panel was shipped and dishwasher lasted just under one more year with same issue. Another extended warranty was offered for $199.00. Needless to say we are buying a new dishwasher and not a Maytag or Whirlpool. The panels are notorious for rusting out. Hmmm moisture of a dishwasher and parts easily corrode.

Since the day the Neptune washer and dryer were installed, the washer has given me nothing but problems. It vibrates so badly and dances all over the floor.I have had the repairman over at least seven times and, now, it is out of warranty so I am spending my own money. The last service man was from Hurst Appliances in Regina, SK. He removed the pedestal to see if this might be the problem. He also sold me some foot pads for $50 that he said might help the problem. However the machine is still vibrating and the terrible mold smell comes out of it as well. I am thoroughly disappointed in this product. I will never buy another Maytag product and tell my friends not to as well.

Maytag bravos xl - HORRIBLE at washing and cleaning the clothes. Broke a little after a year... Went to Maytag site, saw that they push 10 yr warranty. Transmission went out... but not covered?? Garbage.

I could not get parts for Maytag Model MHWE200XW00 Type 832A as the Whirlpool does not provide after sales service. I purchased the new washer in 2010 and lasted for just 4 years. I believe they guarantee supply of spare parts (Inner Basket, Outer Tub and Rubber Boot) for 10 years and more.

Bought a maytag dishwasher 04/12/2013...have been thru 2 control panels...Now installing a third...washer works great except for that!!! Model mdb8949sbb0.

We purchased this microwave in Jan. 2012 to accompany a Maytag double oven for our kitchen remodel. Last night while using the microwave, 2 sparks shot up out of the top of the microwave and an electrical surge noise. I quickly un-plugged the appliance. The next day I attempted to use the microwave again and dense electrical smelling smoke poured from the top of the microwave, again un-plugged the machine. I have called an appliance repairman since the 1 year warranty is up. This machine is not even 2 years old and we will never again purchase a Maytag product. PS If the problem is the magnetron (whatever that is) I will contact Maytag for the warranty information.

This machine is not backed up by Maytag unless you purchase an extended warranty. I tried to contact Maytag regarding this machine breaking in less than two years. This machine has all the bells and whistles but dont expect to use them all because as soon as I used hot water or steam, it affects the lid lock assembly. This should be a recall from Maytag. They know it happens but arent doing anything to improve or remedy the situation. I was only able to use this machine with cold water after this happened. I spent more money getting this washing machine fixed than it deserved. Im so disappointed with Maytags customer service and their product.

I have had it since 2011 and still works as good as it did back then. I love it. Hope it helps people decide when they go shopping for a dryer. I have a dog so I have to keep her clean so I wash a lot of her bedding and she sheds a lot. She also sleeps on the with me so that other bedding that I put for her on my bed between her clothes and mine which I do separate. The dryer works a lot and it is still going strong.

MODEL # MDB4949SDMO. Purchased Maytag Dishwasher. 07/2014 stop working. I have purchased a Maytag Washer also. It also did not last two years. I am very unhappy consumer. I will not purchase another Maytag appliance. Stop selling these lemon appliances. Need to repair free.

Dark clothes are left with residue on them, have to run another rinse cycle to get them clean. Been having this problem since we first got the machine. Anyone else having this problem or got a solution to fix it?

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....

My clothes come out extremely wrinkled and start piling after a couple of washes. I wash on cold and do not overload the machine. I am 64 years old and had always loved Maytag until I got this set 4 years ago.

First, the machine is a wrinkle monster no matter what I try. I wash my clothes on delicate cycle to keep the colors longer and so my clothes last longer. This has never been a problem with previous washers. I take them out IMMEDIATELY as soon as the door unlocks and shake them out and hang everything to dry. This worked great previously and I never had to iron anything or put anything in the dryer to get wrinkles out. Now, this washer wrinkles my clothing to an unbelievable extent so that they need to be ironed or a round in the dryer to relax them. This is true on Wrinkle Guard and using the delicate setting, set between medium and none on the spin cycle. Wrinkle Guard? I don’t think so. This thing wrinkles my No Iron shirts so they will have to be ironed or steamed.The washer leaves lint like residue most all of the time on dark clothing from day one. I most recently did a load of black only clothes that I did on delicate, soil level between med to extra heavy, spin speed between med and none, and, because of the dirty clothes issue, I had the extra rinse on. The clothes came out dirtier looking than they went in and looked like I washed them with a box of tissues and too much soap. They looked dirtier than before I washed them and had a whitish and lint like residue on everything. So I ran them through the same cycle/extra rinse again but WITHOUT any soap. Unfortunately I didn’t watch to see how much water the machine sensed that these loads needed and I didn’t see how much water was there - but I did for other loads after - see the next problem below. After the second identical cycle, the clothes had the same residue which I photographed and have enclosed below. (And still a wrinkled mess.)We have found that the water sensor can’t sense the proper water level needed and is likely not functional. Sometimes it seems like it might almost be be appropriate and sometimes not at all. Specifically, after I ran the black load through, I decided to try a small red load before my usual large blue load just to see how much water there was. Same settings as above, 6 small items that barely covered the bottom of the drum and the washer sensed a medium load. Certainly by volume of clothing this was not a medium sized load and if it goes by weight, it was the smallest load possible! Medium water level… These clothes seemed to agitate ok because they were completely submerged in water and came out clean. Then I did the much larger blue load that filled the drummer then halfway. This had so many more items than the red load and weighed way more. I tried the same settings as above and this time the machine sensed a SMALL load and the water level was barely halfway up the clothes, if even that much. So half of the clothes were out of the water and we watched and witnessed that the clothes did not agitate properly. This load came out like the black load so I ran the whole cycle again including the double rinse. This time, the same load was sensed to be a MEDIUM load although NOTHING changed except that the clothes were damp and lower in the tub as they were compressed from having gone through the entire wash cycle. They came out mostly clean, after the second wash, again, likely because this time they were almost covered by the water (2/3rds or so) and could move around a little better but still not great agitation.There almost never seems to be quite enough water so that the clothes are not able to move by the agitator and sometimes we watch and can see that the clothes above the waters never get pulled into the water. I understand that this machine may not completely cover the clothes but this seems way short on water and the fact that things usually come out dirty means something is wrong. There is often so little water that the agitator can’t possibly work the clothes into the water. So, next I ran an Oxi cycle and witnessed that about half of the items were not in any water and were only wet because of the filling cycle not because they were moved around by the agitator. How can the oxi do its job if the clothes aren’t in the solution of at least wet from the solution which I didn’t see as likely as the clothes didn’t seem to move through much if at all?Along with the same water sensing problem, why on earth isn’t there a manual water adjustment? If the water sensor doesn’t work, the other option is only the high fill setting. After finding my clothes still dirty when we first got it, I tried the high fill setting to see if this would help but the clothes still came out with that residue. This was the very first few loads I ran and was assuming it was just user error so I studied the manual and tried everything as recommended. Since reading that residue can result from too much water, I use the recommended sensing feature now. So, we can either have too much water or barely any at all…

On June 5th, my husband turn off the water to the house since we were going to be away for 4 days. Unfortunately, it was not completely turned off. When we left, the washing machine was OFF, with the door slightly cracked open (to allow for circulation). When we returned, there was water all over in our upstairs, plus water had gone down the walls to the lower level. We could not figure out how the water got into the washer since it was turned off. The insurance company asked that we call a repairman to find out what was wrong. Fortunately for the repairman and us, the machine continued to go on and on after the Curtis had checked it out (it pumped out for him but not for us) and turned it OFF. It jumped from cycle to cycle after he had turned it off. Obviously the control board did its own thing. Be aware-- it can happen!!

Maytag Bravos Commercial Washer MVWX500XWO - This has been the worst experience with this $900 washer and breaking down in less than 2 yrs. Complete Garbage, New Locking Mechanism, now spin cycle not working. I am about to take back to Home Depot and let them have it. Garbage product - NOT WHAT MAYTAG USE TO BE... NORMAL 10 YRS NO ISSUES THIS MACHINE - STAY AWAY FROM.

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

Like in a previous posting I also have a Maytag dishwasher, model MDB7749. Just this weekend we had our third control panel go up in flames. Thankfully the breaker hit and it burned itself out quickly. We had previously had one go out where it would just restart in the middle or near the end of a cycle. One other time, we heard the popping and saw the small black smoke come out from under the panel covering. This last time we were in the other room and heard the popping, and then smelled the burning. Aside from the panel issues, this has been a decent dishwasher. But at this point with a third repair I could have bought a new one. This is the only appliance I havent bought the extended warranty on and I regret it. Hopefully Maytag will add this to their previous recall.

The ice maker in my Maytag French door refrigerator quit working 11 months after purchase. It was replaced under warranty, but again quit working 12 months later. That one was replaced at my cost, and lasted another year. It was again replaced at my expense and that lasted two years. I am now back to the dark ages of filling ice cube trays. I have been reading reviews, and find I am not the only one who has had problems. My letter to customer service was responded with a sorry about your luck letter. I would never purchase another Maytag appliance.

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

I bought my Bravos x washer and dryer set three years ago. Ive never been happy with them. You have to put the washer setting on bulky to even wash a normal sized load and they still dont come clean. Only three years old and Ive had problem after problem with the washer. As Im typing this I have a full load of clothes in the washer that will not wash, its full of water and wont even drain and spin. PLUS the lid wont unlock. So aggravated.

Bought in July 2014, third service call already! To replace my 6 years old Maytag Centennial thinking I was doing a good thing to upgrade to an HE... HA! Jokes on me! Washing machine: Water level. How can you wash clothes in 1 inch of water??? Noise. Very noisy at every cycle. Shakes and easily unbalanced. Clothes are still dirty after wash (obviously if not enough water). Dryer. Noisy with sporadic blower sound (like a plane taking off - high pitched). Three service calls in 6 months??? 2 calls for cable suspensions and now waiting over a month for the tech to change the drum completely. Good thing that I took an extended guarantee, for an extra $300.00!! After Ive read the over 400 complaints about this product, I really feel like I got screwed! My last Maytag EVER!

Quiet, efficient and leave you with clean dishes & utensils at the end of its multicycle cycle. This unit can self-clean and is always beautiful with its shine finish stainless steel interior. This unit can be installed by any user as it comes with everything one will need to complete the installation.

I purchased a Maytag washer the centennial commercial technology model about 4 years ago. At the just barely 2-year mark it needed an all new transmission (Approx $800) Thank God for extended warranties. Now it is doing the same thing again making terrible noise. For a purchase of $1000 this is not good quality or decent workmanship And Maytag does not stand behind their product. I guess I need to buy another brand from now on. Please beware of very costly repairs with this one.

I have the model with a smaller oven on top. I use it about 98% of the time so Im not wasting energy having to heat a larger oven space. I also like the fact that I can clean one oven. The larger oven is used when I cook turkeys. I can cook many dishes at a time, by using the smaller oven for dressing or cakes.

First I do like the fact that it spins at such a high speed that the water is mostly gone, and that is the good news. I do like that it uses less water but when washing any dark colored clothes there are dirt or scum like marks where the clothes may have been folded or twisted in knots which I also do not like. I have cleaned machine but this started when new. Drying doesnt get rid of those scum marks either. I never had this problem with my old full fill machine. I have used more detergent and less HE of course in both liquid and powder. Any suggestions?

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

Maytag Bravos Quiet Series 300 - Just DONT BUY this junk. We bought the washer and dryer set from Home Depot in 2011 and have had nothing but trouble with the washer. Three times small objects like dimes, pennies and nickels got past the agitator into the drain pump which has been replaced twice. Beneath the agitator we even found a few missing socks. Today after a visit to the Laundromat, we bought a Samsung with a 5 year extended warranty. If that doesnt work it will be an old fashioned Speed Queen next. We will never buy anything Maytag again and I hope to influence everyone we meet about them. I cant wait to throw it into the city landfill for recycle dog food cans.

I recently purchased a Maytag French door, bottom freezer. It was delivered and set up by delivery men and when they pulled out the bottom freezer the bin and tray were missing. This refrig should have never been shipped (per Home Depot) and also delivery men. They called Maytag and ordered the missing part. 5 days later it arrives and is not the right bin. I purchased the 5 year warranty contract and after calling 3 numbers and getting shuffled around, they told me it should also have a slide out. They set up appt. for this Thurs. I wanted to file a claim for loss freezer meat and was told Miss, your 5 year warranty does not start until the 1 year manufacturer warranty is up. She also proceeded to tell me that no refund will be issued and they are NOT responsible when their product leaves their plant and gets to me. REALLY... The refrigerator was not properly inspected and still shipped. Not covered under warranty and fridge is 5 days old and have had issues from date of delivery. I will never make another purchase of a MAYTAG and their customer service could use more training and a course is representing their company in a much better way.

It went bad, then I called a technician who replaced the compressor. After a few months, it broke down again after I had bought new parts for it. I was very dissatisfied with how the refrigerator was built. I spent lots of money on it, and it wasnt worth it.

We bought the highly rated Maytag Bravo washer and dryer in March of 2010. In less than a year, the dryer broke down and the drum drive belt had to be replaced under warranty. Last month the washer drum stopped turning. A & E Factory Service quoted $466.87 to replace the bearing that had failed. We have hated this washer since the day we got it. So, it wasnt hard to buy a Samsung front loader and have the miserable Maytag hauled away to wherever badly designed machines go. Trying to wash clothes using high speed spinning instead of water causes excessive wear on the clothes and the machine as well as tying the clothes in knots. It is one of the worst mechanical designs I have ever seen.

This is my second washer in less than 5 years, going third. No customer satisfaction. Maytag/Whirlpool dont care, Customer Service doesnt care - all I hear when I call is, “too bad”, “so sad”, “call a repairman”, so you can spend another $100.00 plus. I hope this doesnt happen with someone elses brand when we buy it. Shame on such a big company.

The HE version of Maytag washer leaves the clothes smelling bad. There are suggestions to remedy this, but why do these type washers cause this? The suggestions dont work. No more HE washers of any brand.

My fiance bought this dishwasher 5 years ago but has never been able to use it due to the fact he is disabled and unable to open the door. When I moved in 4 months ago, I began using it regularly 2-3 times a week. Yesterday, I loaded it and when I hit the start button, it did nothing. The lights come on but the start button doesnt seem to be working. I have torn it apart twice and after looking all over the internet have determined that the control panel is bad. We live on a very fixed income and fixing something like this will take a large part of our budget. I am shocked that something so expensive can only last a few months then stop with no warning. We will be calling and adding our names to the list for the class action lawsuit here in California.

The washer that always needs repair! My first problem with my Maytag washer was that the sensor needed replacing (wont wash or spin). Since then I have had the sensor replaced and motor replaced. Today, I had to call for a service call, and was told that I have to wait over a week! Bad customer service!

This dishwashers start button stopped working after 1 1/2 years. We did not buy the Extended service warranty. So we are responsible for the service call and the replacement of the control panel. Ridiculous. I called Maytag to file a complaint and they never returned my call. I will NEVER buy Maytag again. There are enough problems posted to know better. This company should be ashamed!!!

I bought a new Maytag dryer model # MEDC555DW2 18 months ago. Prior I had owned a Whirlpool for 22 years and the only expense on maintenance was that I replaced 3 belts. This new Maytag started making a terrible noise so I called the store where I bought and they sent out a tech. $76.77 they charged me to...remove a penny from where it got lodged in the edge of the drum somehow. Maytag refuses to do anything about it and I feel like Ive gotten the shaft because I bought an inferior product. In 22 years Id guess I dried on accident over 100 dollars in change since I have kids. Should have bought a Whirlpool again and so should you. Ill never buy another Maytag product. Ever.

I bought it from a local dealer so that I could get it serviced locally. I bought it in 2012 and paid $750 for it. I hate just about everything about this (and all modern) washing machines. The deal breaker is all these safety features that are really inconvenient and pointless. If I could have found a good used washing machine at least 10 years old, I would have bought it. This is a Maytag Centennial. I dont like the automatically locking door, the inability to choose the water level myself, and the requirement to use a particular kind of soap. Also, I hate the idea that I have to clean the washing machine from time to time. Whoever heard of that? But you have to do it otherwise your clothes will have a sour smell. These new washing machines are not an advance in technology. I may have to go back to using a wringer machine.

I have owned this washer for 3 years and purchased it to match the Centennial Dryer and because of its advertised commercial grade components. The washer has just now turned 3 years old and has never been abused but I have been told the drum bearings are going out.

Bought a Maytag bravo xl washer and dryer two years ago. Spent around 1,500 dollars. Didnt make it a year before things started going bad on them. First the lid lock on the washer broke. I got the lid lock pulled out far enough that I could drill a hole in it and tie some thread to it to pull it out when the washer was ready to lock. Today the piece of junk just quit. Not long after the junk washer started messing up the dryer starts sounding like a fork in the garbage disposal. It still works and dries the close but you hate to even turn it on because of the noise. I will never purchase anything maytag again in my life. JUNK!

This fridge is a piece of crap. Bought brand new and right after warranty the freezer started freezing up and leaking all over the floor, ruined the wall behind the fridge which created mold as well as the puddle on the floor that multiple people in my home slipped and fell and it started shocking anyone who touches it. Called a repair man he says he doesnt know why its shocking probably is the manufacturers fault as well as the defect causing it to freeze up and leak. I call Maytag and the guy doesnt seem to care that my 7 year old has been shocked and says unplug it and I will just need a new fridge. I already spent the money on the new fridge. Why should I have to go buy a new one now after 2 years, that I cant afford. Its ridiculous how many other people are having problems. Its a defect and should be recalled and they should have replaced the crap fridge they sold me in the first place. You would think for such a big company they would do something but yet people are getting seriously injured and this seems like it should be taken to court for a lawsuit. I am extremely unsatisfied and wont ever buy a Maytag and will let all my family and clients through my cleaning business not to ever purchase a fridge from Maytag.

I just bought my first home and after well over 20 years of apartment living and not having my own washer & dryer I was so excited to finally be able to buy one! I decided on the Maytag/Bravos and even spent the extra $100 for the glass top. The high efficiency machine was delivered on August 8, 2016. My kids are grown so its just me; I do one load a week give or take. A week or so ago, I noticed the washer was taking an inordinate amount of time to go from sensing to washing and even longer to get into the washing cycle. This past weekend, it didnt work at all. Just sat for hours with the sensing and washing lights on, without actually washing the clothes. The machine was packed loosely with the correct amount of High Efficiency Detergent in the proper place. I called the #Sears store I purchased the appliance from (Braintree Ma.) and they said there was nothing they could do as it was past 30 days, gave me their customer solutions number which is basically a call center with people who I could barely hear and/or understand. They in turn gave me more phone numbers which seemed to me to be in the same call center. I want to return the 4 month old washing machine that doesnt work and I want my money back. Ive filed a report with the Massachusetts Attorney General Consumer Affairs Department. I will NEVER AGAIN shop at #Sears and I will NEVER AGAIN purchase a #Maytag appliance. I am beyond disappointed in #Sears and #Maytag, both names that used to mean quality and customer service. And if theres a class action lawsuit to be filed, please count me in.

Barbara ** purchased a Maytag Bravos X washer. The washer did not perform anywhere near the advertised and EXPECTED performance. A letter was written to the Maytag Customer Center on July 12, 2014 complaining about the washers inability to clean or rinse clothes effectively. As of this date we have had NO direct contact from Maytag. After reading many reviews and noting that I have seen over 700 people which had issues with this machine, I wish that I had never purchased from Maytag. I have had to purchase a new machine to replace this useless Maytag. When I ask a used appliance dealer if he would be interested in purchasing my Maytag Bravos, his reply was, I dont want any Maytag Bravos in my store.I have made an effort to obtain some type of satisfaction from Maytag, but to no avail. I would like 100% refund for this purchase. If Maytag does not meet the expectations of its customers, then I feel that a class action law suit should be started through consumer affairs. When you cant even get a used appliance dealer to purchase a used Maytag Bravos, then there is a real problem with the product. The purchase price was $616.55. A total waste!!

We purchased a $945 Maytag 6.4 Cu. ft. self-cleaning freestanding electric convection range which was part of the stainless-steel package for $3600 + a $600-dollar 5 warranty. I did the research and found a solid 4.0 rating, so I went for it. Now I wish I never wasted my money and time. My 5-year warranty for all 4 appliances expired on 8/17 and now everything starts failing, how convenient. The oven will not heat past 340-350 degrees which won’t work with 90% of the stuff I bake. I called Maytag to see if it can be fixed and was quoted $400 for the issue but nothing else. I can pick up a new stainless-steel oven with the save features on a holiday sale for $500. Don’t waste your money on warranties!

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.

Overall- I think washers aren’t made to last like they once were. Growing up- we had the same washing machine while living at home. It seems now- they only last 10 years if you are lucky. They should make more longer lasting machines.

We bought a Maytag refrigerator (single-door) with a top-loading freezer that failed after four years. The freezer began to ice up and two repairmen from the company that does the extended warranty repairs in the Ottawa area were unable to figure out the problem. After the second visit, the freezer iced up again and the thermostat appeared to be failing. Even though we had an extended warranty, we just gave up and went to a different dealer to buy a new refrigerator that could be delivered within three days - and it wasnt a Maytag or any other of Whirlpools brands. If youre thinking of buying a Maytag refrigerator, you should reconsider. In fact, you should twice before buying anything made by Whirlpool.

In May 2007, I bought a matching Maytag Neptune washer Model MAH5500 and dryer. I also bought the 3-year extended warranty. Approximately 4 years later, actually 1 month after the warranty had expired, the washer started to get very loud and sounded like a jet engine taking off. I called Brennen Repair Service in Midland, Michigan. The repair man came out and said he did not even have to look at the washer. He knew what was wrong. The bearings were going in the machine. He said I could fix it for approximately $600 or just run it till it quits. I was furious. I called Maytag and explained my issue and was told that there was not a recall and they could do nothing to help me. They even told me that they had not had any complaints of this nature regarding this model. I told them they were full of it. I know of at least 4 people in my family and workplace that have had to replace the Maytag front loader piece of ** washing machine. I think Maytag should stick behind their product with all the complaints out there. I would like to shove my washer through their front window. I previously owned a Maytag washer for 25 years and had not one issue. It ran perfectly. I will never buy another Maytag product nor will anyone in my family. Maytag, you suck. Your service and reputation is appalling.

After less than 3 years the interior lip of the machine is rusting. I found this when I was cleaning the interior of the machine because my white clothes were coming out with black soot on them. I can estimate that bleach was used in the dispenser 3-4 times tops over these 3 years. Very disappointed in the equipment. Ive submitted a complaint to Maytag with hopes of a favorable response. This should not be a warranty item...its defective design.

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

This washer has been the biggest disappointment of any appliance I have ever bought. Purchased 12/2012 and immediately disliked it but thought I needed to get used to the new style since my previous machine operated for 23 yrs! It is loud and does not clean as effectively as my last machine. It stays in the Sensing mode for 15 mins or longer. Rarely will it spin as it should. Most loads, after the sensing stops and the lights go out, I have to move the dial to Drain/Spin, wait for it to sense again and then maybe it will spin. If this doesnt work I have to unplug the machine to allow it to reset. I called Maytag and was told there are no known issues with the machine. I google this model and find many customers have had a similar problem.

My washer is just past warranty and making horrible sounds! I have always liked Maytag but their quality is bad. I wish I had read reviews before purchasing my washer and want to tell anyone reading this to NOT buy one. My last Frigidaire washer lasted 15 years with minimal repair. Shame on you Maytag!!!

We purchased a new Maytag Bravos X washer and dryer from Lowes in June of 2013. After a year and a half of normal use (2 people in the household) the washer needs a new gearbox bearing at a repair cost of $529.00. I called Maytag and spoke to a customer service representative who informed me that there was nothing they could do about it because it was past the one year warranty. I asked to speak with a supervisor who told me they would offer me a 50% discount on the bearing but would not pay for the repair work (the cost of the bearing is approximately $25).Needless to say I will not be having the washer repaired. We will be purchasing a new washer and it WILL NOT be a Maytag, Whirlpool or any other brand made by that company. Its just appalling to think a company like Maytag can scam customers the way they do by producing appliances that are of such poor quality and then offer third rate customer service on top of it. Maytags answer to the whole issue is selling everyone an extended warranty which we all know is as bogus as the companys integrity!!!

I have a self cleaning Maytag electric stove. I discovered the self cleaning starts after so many times of using the oven. But the stove didnt give me warning of this when I put my Thanksgiving turkey in the oven. Halfway through cooking, the oven door locked and went into cleaning mode which scorched my turkey and could have possibly caused a house fire. Also, my top burners have a mind of their own, while cooking they turn up on their own. This stove is very dangerous.

Neptune 4000 washer - Worst washer EVER! Two weeks after we bought it sounded like a jet engine during the spin cycle. They replaced the bearing parts. Only cost us 450 in labor. One year later, again the bearing but this time we insisted on full coverage. 6 months later, here we are again! Most expensive washer in the history of washers and this is a KNOWN issue - yet Maytag gets away with it while consumers foot the bill! Ridiculous! Never again will I purchase their product and make dang sure everyone I know stays away too and everyone that hears my washer is in shock that it hasnt injured something or someone. Its only a matter of time!

I purchased a Quiet Series 300 E71195 dishwasher in 2011. Its about 3.5 yrs old. I guess misery loves company because like so many other complaints on this site my control board died, and Maytag, while saying they care about customer satisfaction, basically said tough luck pal, youre on your own. Sadly I own 3 other newish Maytag appliances. When will these appliances die without support from Maytag? Im not holding my breath. My next step is to complain to the dept of Consumer Affairs and create a page about nefarious Maytag on social media. Avoid the Maytag brand when shopping for appliances. I know I will.

Neither appliance (Neptune dryer and washer purchased in 2006) was worth the price paid. The dryer drum actually cracked and the washer repeatedly gets hung up on 3E. I called about the dryer and got an Oh, well response. “We dont know whats happened to that dryer.” What happened to both appliances is that they were used for their intended purpose. I do laundry for my husband and me. Is that too much for a Maytag? Customer service is equal to indifference. So much for Neptune. And thanks for standing behind your products. What is the life expectancy of a dryer drum anyway?

Maytag 7000 series front loaders bought in 2013 on basis of high ratings from Consumer Reports. Also durable and look good in the process. Had for 3 years. Machines highly rated by Consumer Reports and bought on sale. They were a very good value. Both W & D have steam feature but find Ive rarely used it. Durability is key, as is the ability to balance wide variety of loads, which our machines do well. Capacity of 5 cu ft or better sufficient for a household of 2. Maytag reputation for durability and reliability and made in US, though a clone of Whirlpool. These are big, heavy machines, best for side by side but they can be stacked. The units are quiet, have more features than weve ever used and so far have been reliable, gentle on clothes incl delicates and drum bearings really help with keeping loads balanced. Door hinges built like a tank but the chassis theyre attached to arent up to par. W & D have stainless drums. Washer is resistant to mold & odors but dryer lint system convoluted in design and hard to clean out.

I purchased the Bravos XL washer and dryer from Lowes in March of 2011. I had only had my dryer for a couple of months when it stopped drying out of nowhere. The repair man came and replaced the fuse assembly and all was well until December 2011. Again the same problem happened. I had to wait almost 10 days for someone to repair it. Once again in January 2012 for the second time the fuse assembly was replaced. Its now December 2014 and again my dryer has stopped working. Have to wait again 10 days for anyone to come and fix this. I will never buy another Maytag dryer again.

We bought this Maytag MFI2269DRM01 Fridge/Freezer in June 2016. We have nothing but trouble. First the center rail holding up the Fruit/Veg drawers snapped within a month then the freezer drawer would not close properly which gave us all sorts of problems (door open lights flashing and fridge staying on longer. Lights not working etc.) The service tech came out and tried to fix it and went away saying it was not repaired that he would need a new freezer drawer. In the meantime I had to push the drawer to try and get it to work right. Now the handle is loose and the stainless steel front of the drawer is damaged by pushing it in so much.This repair started in November and now it is the end of March. I asked them to replace the complete unit but they say that the warranty is just to repair. It seems like they have no parts to fix this. Then the new center rail snapped again!!! When they sent the part out to me to install, I found the main frame of the Fruit/Veg rack at the back had snapped. Everything is brittle plastic with not enough support. (The only vegetable that I think I can put in the drawers is mushrooms.) I thought by buying a Maytag that the name sold it. What a piece of junk it is!!! Will never buy another Maytag product!!!

We purchased a Maytag Centennial washing machine from a local business here in Knoxville in 2013. My previous Maytag lasted seven+ years and I was very happy with it. It began to leak water and after two times of having water on the floor, we decided it had worn out and purchased another washer. We immediately wanted another Maytag since our previous one has lasted for quite a while. We bought the new Maytag Centennial washing machine in the Spring of 2011. This is May of 2013 and we have had to purchase another washing machine since the electrical board in ours went out. The replacement part is listed at $300+ and that is without labor to install. Needless to say, I am very unhappy that I have had to purchase another washer so soon... and did not buy a Maytag this time.

Has had problems with machine being off-balance and clothes getting clean. 3 years and now the machine is broken. Too costly to get repaired. Warranty only covers very specific things. Have had Maytags repair person come out and he did not access the problem properly. What a waste of time and money! Says it needs a very expensive part which with labor and parts cost almost as much as machine.

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

Horrible washing machine. Cannot get clothes clean. It simply does not supply enough water to wash. Have tried everything. I want my money back. How do you start a class action lawsuit. Thousands of people are dissatisfied also.