Dont buy this machine. Although it is an HE machine and supposed to save on water, it does not give enough water to at least cover the clothes. I had repair come in and they changed the computer but no improvement. The cycles determine the water amounts not the type of clothes you are washing. So if I only a few things I use cold water wash, if I have a half load I use deep water wash and have to add water to it. Its ridiculous. Do yourself a favor and get an LG. I wish I had.

I bought a Maytag laundry set (washer and dryer, models MVWC565FW and MEDC555DW, respectively), and I concur with the fact that this is the WORST laundry set I have ever owned. The clothes came out of the washer extremely dry and did not come out as clean as expected. In addition, clothes came out with strange spots, especially the dark ones. Now, we wash our dark clothes with fear of damage them. The dryer is also pathetic. I put in a normal load on high for 60 minutes, and theyre still very damp. Sometimes I have to repeat the cycle 2 or 3 times. When I compare it with my old laundry set, this is extremely disappointing. And to make things worse, the customer service department doesnt answer you. I sent them a mail, on February 2018, and a month and a half later, I havent heard back from them.

We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

We purchased a MAYTAG refrigerator when we recently built our present home. This refrigerator has been a nightmare! Ice forms in the bottom freezer and then constantly melts out of the bottom of the appliance all over the floor. Weve had a number of service calls with no real effect. The computerized function that sets functions do not work well and often shut down the appliance with little clear way to start it up again. The ice maker/dispenser often clogs up or will not produce ice. Weve had it! We broke down today and spent the money on a new GE refrigerator. My very strong advice is DONT BUY A MAYTAG refrigerator with the freezer on the bottom!

We bought a Maytag washer and dryer in April 2012. A few weeks ago the washer while it was spinning out, it sounded like it was metal on metal. Sears came out and said the transmission and the tub had to be replaced and the tub was created to the transmission. My husband and the only ones living in home and I sort my clothes, so I dont have big loads. I contacted Maytag, their answer was its out of warranty so we are not going to do anything for you. Anyone who buys a Maytag Washer, watch out what youre getting.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

I bought a Maytag microwave in Feb of 16. Six months later, last August, it stopped working correctly (light doesnt come on, will not start, continually says open/close door to start). I have been trying for THREE MONTHS to have this fixed. Multiple calls to Maytag have resulted in nothing but empty promises. Calls to the store where we purchased it do no good - you have to call Maytag. We got 6 months use out of a Maytag microwave which we paid EXTRA to have installed. At this point I dont want it fixed. I want it replaced. The Maytag brand used to stand for durability and integrity; now it stands for badly made products and pathetic customer service. Look up my phone number on your computers, Maytag, and you will see all the efforts Ive made to get this fixed.

We have had and used this washing machine for over 25 years and only had one small problem and that was to replace the lid switch and the machine is working today as good as the day we bought it, it has went through raising four kids and many grandkids.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

Maytag is the worst washer company. I owned my washer for two years and I had two different problems with it and now I have a 3rd. The first was the same day they delivered the washer, I needed a wire harness. I should have returned it then but I didnt. The 2nd was six months after the first one. A wire came loose due to the washer shaking and the 3rd, Im not sure why it wont drain but the tub is full of water. I called Maytag and they really didnt care as long as they got their money. They referred me to three companies that fixes washer. Two of three was already out for this washer. If I didnt know any better I would think Maytag gets paid off for every customer they referred to these companies. I would never buy another Maytag Bravo or Whirlpool product. Im very dissatisfied with their Bravo washers. They lost a long time customer.

Maytag WFW7590FW & YWED75HEFW 24 Compact Washer and Dryer: These 2 machines are a lemon and the extended warranty plan was completely disappointed. Both needs maintenance before the 1 year warranty ends. The washer was the worst between the pair. The washer cannot spin the laundry dry. The Home Depot extended warranty plan was not the cost. It takes 2 business day for the service call to call us back. Then a schedule date was 2 days later. The service person complained about not getting authorization to do the work without charging us. He did even showed up for the 3rd call. He did nothing to resolve the issue and said the diagnostics showed there was a load issue, which was not true. A very light load still didnt spin dry. The washer not spinning clothing dry issue has been more than 1 month and is still not resolved. The repair person Dean didnt even re-schedule another date after not showing up today. There is a 90 day policy that we cant request for another repair person to attend to the issue. The dryer also made excessive noise which was caused by a broken attachment that established the drum.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

My Maytag dishwasher will not come on and it is loaded. The control panel is out for the third time.

We purchased a Maytag refrigerator Model # M1TXEMMWS02 and Serial # E01103420 in April of 2010 from Home Depot in Aurora, Illinois. First off, we did register the fridge online via Maytag which of course, they have no record of! Now, we go on vacation and come back to all of our food ruined because the refrigerator stopped working! No refrigerator should stop working within two years! I called Maytag and they offered me a Repair Plus One package of $302.73! Are you kidding? We paid $400.00 for fridge. Then of course, only one-year warranty and have to pay at least $75 for a service call, labor plus parts! If it’s the compressor, the charge is $326.20, plus shipping and handling! What a joke! There needs to be longer warranty and should offer free service calls and much more. I am disgusted in Maytag products and in which we purchased due to a reputable name! Never again.

The range I have works awesome, which is surprising for an electric stove. For being 11 years old I am happy with how it is still holding up. The only thing I would improve is if it was a double oven instead of a single!

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

I purchased a floor model Maytag Dishwasher from Abt electronics about a year and a half ago. 2 months ago, various light started flashing. Somehow I managed to get it going. Some blogs reported it might be a drainage problem. Others suggested pressing a certain sequence of buttons. After Each time I got it to work, it became harder the next. I bought Maytag because my old dishwasher lasted 13 years. What is interesting is that a company whose name Ive forgotten sent me bimonthly requests to purchase a warranty from them. Now they have stopped. I am a single mom of 3 with an unemployed ex. I work and support my family without any assistance. I count every penny. I cannot afford repairs nor a replacement now or any time soon. This is a travesty.My door says 10-year limited warranty and the delineates stainless steel tub and racks and chopper blade, but not the panel. I do not understand how Maytags denial of the problem and their unwillingness to correct the problem can improve their image. I will never purchase from Maytag or its associated companies ever again. What a scam! To be honest though, I have not contacted the company since it is not under warranty and all the blogs have relayed the same message: Maytag denies there is a problem.

Washer sounds like gearing is broken, is noisy during operation, various combinations of options dont work, appearance of only one agitation cycle combination on washer, just many settings but all with the same response; dryer does not timely dry clothes, all settings default to the same palpable heat temperature; clothes take much longer to dry in new dryer than they did in old Maytag. Newer Maytag set appears to be secondhand garbage sold as new by Menards. Company unresponsive to complaints.

Bought top of line Maytag dryer and washer in 2011. Immediately had problems with dryer. Dryer resets timer itself to outrageous times. Clothes so dry they could have been parchment. This has continued with multiple service calls and electronics replaced. Still continuing but they will not act lemon law. I have extended warranties but get runaround everyone including Sears where I bought it pointing to each other. Tech came out today and said problem was the way the dryer is. No way to change it. I guess that is nature of the beast. I will never buy Maytag or from Sears again.

18 months old washer breakdown #6 - I purchased a new out of the box washer from Aarons model #MVWC7ESWWO and since Ive owned it, it has broken down repeatedly with the same problem - a water inlet valve. As a child seeing the commercial with the repairman with nothing to fix played a part in my purchase, I couldnt be more unhappy. With a family of five, there is laundry and not having a reliable washer does present a problem. I sent you this while waiting for the part to arrive from Sears. Sincerely, an unsatisfied customer.

Bought it in 2013. Just replaced freezer motor. I thought for sure it would give me better service.

Brand New 2017 Maytag Dishwasher MOB8959SFZ4 - The first time we used it it leaked from the door. I called the plumber back to make sure it was level and lined up properly and it was. Called the dealer, they sent a technician who sent away for a new latching mechanism. 3 weeks later the parts showed up. Technician installed them ran it through empty and no leaks problem solved? Nope. So I loaded it up and ran it again and it leaked. Called the dealer back but the technician is away on vacation.They suggested that the top rack might be pushing against the door for some reason when it is loaded so I removed everything from the dishwasher and ran it through again but it leaked again.Its something to do with the door not latching properly and it doesnt have a lever that locks like the old ones did. Its such a flimsy product. It baffles me that importers are getting away with bringing this crap into the country. Im now in week 5 with a brand new dishwasher that doesnt work. Maybe thats why its known for being one of the quietest dishwashers on the market.

We have had our Maytag dishwasher MDB9100AWQ only 5 years and now it keeps shutting off. I see there is plenty of this complaint. I will not purchase another Maytag product after reading all these reviews and experiencing it.

Control panel is defective on my Maytag dishwasher. Found a phone number that was created to deal with this problem. I only had to hold for a few minutes but the first person I spoke to was rude and unhelpful so I asked to speak to someone else. When another agent came on the line I told her that only the normal and rinse button light up but do nothing when pressed. She arranged for a repairman to come to my house and determine if my control panel is defective at their cost. When he arrived he asked me what the problem was and I said, The touch pad control panel is not working. He stated, Your control panel needs to be replaced. I have to order the part and come back to fix it. He was there for about five minutes and he never laid a finger on the dishwasher. When I asked if the control panel design has been fixed he said, No, you will probably have to replace it again.There is a video on the internet that shows how to seal the electronics with silicone. The repairman said that they cannot seal the electronics unless Whirlpool provides a kit to do it. I guess the Maytag repairmen may have to come out of retirement. My husband will seal ours after it is replaced so we hopefully dont have to deal with this problem again. So now I am waiting to see if he returns in a reasonable time frame and gets my dishwasher going. There is a class action suit about this issue filed in 2013 about this defect.Updated on 09/23/2015: A repairman came to my home on August 20, 2015, at Whirlpools cost, and he determined my touch pad did not work. He informed me that Maytag would provide the part, free of charge, but it would cost me 85.00 for them to come back and install it in 2-3 days. As of today I am still waiting for the part to come in, apparently due to high demand Maytag was out of touch pads, which were out of stock. No idea of when that would be, the repairmans company said, dont call us, we will call you when the part arrives. So I began to look for the part myself, found a couple on an auction site, but most companies that sold parts were on backorder. Until I found a company that said their inventory was out of stock but they had five, stashed in the back. The price of 105.00 was not that much more than the 85.00 cost for the service call. Got it in two (2) days, installed (in about five minutes), sealed by my husband and I loaded it and washed my dishes. I was so overcome with relief, tears came to my eyes and I almost fell out. I give five star to the fella that had the part stashed until I needed it.The Maytag repairman is still waiting for the part so he can fix my dishwasher.

I bought a new Maytag French door refrigerator a few years ago and have been disappointed ever since. The quality is second rate and now the ice maker has failed. The product looks good but performs poorly. Buy a more quality foreign made product instead. Before this I had an LG which was quieter and never had a problem after 10 years.

The only complaint is the lights on the bottom quit working about a month after we purchased. It was nice to light up the stovetop when cooking. Now it’s slightly dark. I have gotten used to this. We spent about $8000 on all the matching Maytag appliances we purchased. I would love to replace all but not in the budget. I am a dissatisfied Maytag customer.

Purchased new stove from Home Depot. Was delivered damaged after I opened it. Called Maytag and they cannot get a service man there to look at it. They keep on telling me I have a 30 day unconditional warranty, yet they cannot live up to their words. Absolutely amazing. Bought the Maytag because of the 10 year warranty. Do not waste your time. Buy locally at an appliance store not big box stores. Do not buy Maytag either - service is just a bunch of well qualified talkers and key punchers. Very poor buying experience.

I absolutely do not like the fact that you can’t choose what size load you have. The washer wants to do it for you but it is not very good at it. You have to fool the washer to get any kind of water level or just use the deep fill every time which is what I do in order to get the clothes clean! This defeats the whole purpose of trying to save water. Also there are too many settings. I mean we’re just washing clothes here not flying a jet. I personally would prefer dials instead of the digital instrument panel. So much easier.

We purchased the Maytag double oven 30 inch 5 burner, stainless steel, model MGT8885XS. Oven worked good for six weeks. The igniter broke in the bottom oven and when the third party non-Maytag repairman came out to fix it, he was unable to remove the bottom oven door. It is not flush and heat escapes when the bottom oven is on and it causes the top oven to get condensation. The repair man was directed from a technician from Whirlpool that he had to order a new seal and hinges. I dont want it fixed. I want a new one. I have called Customer Service for Whirlpool and the third party and the store in which I bought it from and everyone is pushing it off onto someone else. Customer service is poor and stated they will only fix the oven and will not send us a new oven. We sent our rebate in the mail which was to arrive within 8 weeks and we have yet to receive it. Very poor customer service. Glad I purchased the 4 year warranty. I will never buy Maytag again.

We moved into our first house just over two years ago and decided we needed to get a new refrigerator. We did a ton of research online, reading reviews, etc. We found a few not so great complaints regarding Maytag; however, we took our chances. (Note that we live in a house built in the 40s, so the fridge space is small and we needed a fridge size that is smaller than normal. We didnt have many options.) Well, a little less than 12 months later (yes, luckily right before the warranty expired) our ice dispenser stopped working properly. The mini-ice door would not close properly, resulting in a lot of frost in where the ice door was located. (There was so much we couldnt open the freezer door. It would get stuck.) So, we called out the repair guy and he said he had never seen this issue before and basically had to replace the whole flap and parts. Sweet. It was fixed and cost was covered! Well, about 5 months later, it happened again! Ah, they got it fixed yet again. Well, another six months later and after the warranty expired (lucky us), the fridge completely stopped cooling. (And it just happened to be Halloween, not a great day for a house issue.) So, we had to remove all our perishable food and place it in a cooler (which works hundred times better than Maytag products), and move all frozen food to a family members house 15 minutes away (luckily!). We were also super lucky we found a repair company that could come out at 5pm the next day, which happened to be a Friday! Awesome company (Conners Repair in Metro-Detroit). He concluded the defrost board was broken, meaning it was freezing and creating frost and then not defrosting, clogs the vents and not allowing circulation to occur. He was shocked when he found out we only had this fridge for 2 years and said this is something that normally happens in 20-year old fridges. I then decided to call Maytag and nicely requested a refund for the issue. I was told no due to the warranty expiring and also because we didnt use a Maytag repair company. I didnt want to wait a week as I thought this was something that needed immediate attention. I also am not sure why it matters who you get to fix your fridge. I have an invoice for proof of the issue and the repairman even said hed call to verify the issue. I don’t understand why I have to pay for something that was not properly produced, and not to mention the time out of my schedule to deal with Maytags issues. I now know not to buy any Maytag products due to the lack quality. I guess I learned the hard way.

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

I purchased a Maytag dishwasher model number MDB7749SBM in May of 2013. In August the dishwasher control panel stuck on Rinse only cycle. It has been stuck on this cycle for a month. I contacted Maytag and they walked me through a reset. It has not worked. It looks to me as if the control panel has failed. This seems to be a common problem with the Maytag dishwashers. As soon as the warranty expires, so does the dishwasher. I purchased this dishwasher from Home Depot for over $600 thinking I was buying a quality product. My previous dishwasher was also a Maytag, even a lower end one that lasted almost 14 years! This one has not even lasted 14 months!!I was told by Maytag that I could purchase an extended warranty for $267.45 that would last a year. I believe, 4402 based on other reviews that I will be dumping more money into this one even after that. Very disappointed!! I will never buy another Maytag product again! I should have bought the Bosch. It was roughly the same price and high quality. I bought Maytag based on my previous experience. No More!!

I purchased this on sale at Home Depot, 1 year later this washer top load doesnt clean clothes if the cycle does finish at all. I have to restart the cycle, re-rinse etc, theyre still dirty. I dont have time for that, I have four children and my husband works in construction and comes home with filthy clothes that are just wet and dirty when they come out of this washer. I dont usually write reviews but I hope I can save someone else the hassle. I wish I would have read the reviews beforehand, they all complain of the same thing. This washer altogether is BAD! ITS LOUD, it bangs around if I dont put in the tiniest loads, even then, they come out dirty. Dont waste your time.

Purchased washing machine, with insurance that was offered to me 9/17/10. May 2013, control panel went. June 2013, dial switch went. July 2014 washer motor drive & belt drive had to be replaced. August 2015 is broke again. Will never buy Maytag again.

Please let me know if there is a class action suit. This refrigerator leaks water all my floor every three days or so. I have to chip the ice off the bottom of freezer every three or four days. Storage is also a joke. Poor design.

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

Maytag water efficient, no central spindle top load. Clothes come out with scum on them. Really a problem on the solid darks. I have to scrub with terry cloth to remove. Maytag insists this is normal. Refused to honor warranty. Usually check Consumer Reports for quality and best buy. Energy/water efficiency is important. I like to have some control over the machine so that I can use it the best way for me. Such as soak. This machine cannot be manually controlled at all. Also it doesnt have a lint catcher, doesnt filter the wash or rinse water at all. All the lint and pet hair remains on the clothes or even gets worse.The clothes are not clean. I have no way to control the machine for my use. It may be water efficient but seems to use too little water to clean the clothes. Maytag wants to blame the EPA - This is irresponsible on their part. Its an awful washing machine and they made it. Maytag continued to insist that scum on the clothes was working normally. This scum was added by the machine. I used very little detergent; the clothes were relatively clean - just lightly wore a few days. They come out of the machine with streaks of white scum that I have to scrub off. The clean the machine cycle uses a huge amount of water. This is really DUMB: washing the machine instead of cleaning the clothes! Terrible! And Terrible customer service at Maytag. DO NOT BUY MAYTAG.

Maytag Dryer MED6000XR2 - Purchased in Sept. 2012 - first service call 1/13/14; 2nd service call 2/20/2015 and less than one month on 3/14/15 it goes out again. It takes one week to get service company out and then another week for the part to be ordered and put in. This means I am without a dryer for over 2 weeks. An $1,100 dryer goes out every year and sometimes within one month?! According to the service company, it just is the way this dryer works. Really? If Maytag ever wants my business again, I better get a more justified reason and better than 2 weeks service call. This is absolutely ridiculous.

Maytag top loader washer will not complete cycles. Washer is only fourteen months old. Repairman says parts will cost four hundred and seventy four dollars - almost what I paid for the washer.

Ice maker not making ice, lights on the temperature controller are all flashing, ice/water dispenser door continuously opens and closes, refrigerator and freezer both do not cool/freeze properly. I purchased a new main control and low voltage board at a total cost of $400 and replaced them to no avail. Nothing changed when electronic boards were replaced.

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

I’ve had this new stove just over a week. Used 3 times (I just moved). I have cooked on staying already on the ceramic top. I’ve had a ceramic top stove for over 20 years with barely a mark in it. Terrible. I’ve left a message with the store with no reply.

I have a French door fridge Maytag like everyone else. The bottom freezes over and I have to de-ice it. Now the freezer doesnt want to cool. Its 3 years old. Total piece of junk.

I purchased the Centennial Commercial Technology washer in June of 2013. In the last 2 1/2 years it has been repaired 3 times. The transmission had to be replaced twice. My household consist of two adults and definitely it is not overused or overloaded. The washer currently is not working. Consumer service cannot schedule an appointment for repair for 2 weeks. Previous repairs took approximately 2 weeks to schedule a service appointment and it took another week to two weeks to get the part in and washer repaired. I have decided to consider this an expensive learning experience and will not purchase Maytag products in the future!

My Maytag model MDB7749AWWI was purchased from Home Depot on March 10, 2011. On July 12, 2012, my dishwasher would not start. I had out of town guests and then the repair person was out of town, so I did not get anyone out to look at it until July 31. He stated that we had bad controls. The parts would be approximately $420.61. He could not get any parts because everyone was out of this part. Does that mean that all the dishwashers of this model number are broken? Is there a recall? This is unreal. When I was asked if I wanted extended warranty, I said no. If I needed an extended warranty, the equipment must be junk. Well, I needed the extended warranty. It is junk! I will never, never, never purchase another Maytag appliance as long as I live!

A little over two years and my Maytag dishwasher needs 300 to $450 in repair for circuit board or boards. The repairman said that they got cheap and left out a seal which allows moisture to get into the electronics, duh. They have a known problem but will not stand behind their screw-ups. Never again will I purchase Maytag, Whirlpool or any other product made by the bumbs.

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

Machine is very loud. Clothes do not feel completely clean when wash cycle has finished. I have a sense that not all soap has been removed. Dark clothes have streaks of white residue. Must turn clothes inside out before washing. Very disappointed.

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

I purchased a Maytag Dishwasher in April of 2011 - Ive had four control panels in that time and the panel gone again - in fact, one panel came out of the box nonfunctional (I counted that one as it was installed although the tech removed it when it quickly became apparently that it wasnt working). Ive got a complaint in to Maytag but I have low expectations as to a satisfactory conclusion. What Id like is for Maytag to buy this lemon back from me for around $400 - I paid nearly $600 (including installation). Again, I doubt this will happen. From my research online it appears that the control panel issue is a latent defect which Maytag knows about but either wont or cant figure out how to deal with it or correct it. I have a scan of the receipt which Ill see if I can upload later. I know about one class action lawsuit for CA residents. I wonder if its been expanded.

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

We purchased our Maytag Bravos washer and dryer in 2008. Within a year, the hinges that held the door open on the top load washer broke. In year 2, the area around the fabric softener dispenser rusted so badly that it almost completely ate the porcelain enamel away. In year 4, it started making a noise that I will compare to a jet on takeoff during the rinse cycles. It continued to work but got louder and louder. We looked into the cost of the repair, which was going to be $350 parts + labor. If it had been a good machine, we might have considered fixing it but it wasnt. Even a set of sheets could put it off balance, which stopped the machine with the wash cycle incomplete. It also set its own water level based on the weight of the clothes and many times the top items came out with dry spots that hadnt even been submerged throughout the whole cycle. Consequently, the clothes were never very clean and I would have to rewash many loads. This machine was not cheap - around $1,000. I was so frustrated and felt completely taken by the Whirlpool company again. We have had many unhappy situations with their products over the years - Kitchenaid, Jenn-Air and Maytag. We finally learned our lesson and researched washers online. The best rated that we could find was Speed Queen. We couldnt find it in Canada, so my husband drove 5 hours round trip to the US and bought one. We have had it 4 months now and the difference is unbelievable. Our clothes are clean again. I can set my own water level and the hot cycle actually gives you hot water. It never goes off balance no matter how many or few clothes it has. If I see that I need more water part way through a cycle, it has a button that lets you add some part way through. It doesnt have a lot of bells and whistles. Its a basic but excellent machine that is a pleasure to use. I would recommend it highly. I realize it has only been a short time, but my Maytag never performed like this machine even from day one. It reminds me of my very first washing machine many years ago, an Inglis, which never had a repair in 15 years of use. If our dryer goes, we will definitely buy Speed Queen. The trip is well worth it.

I cant warn you enough NOT to buy this design flawed machine. Ive only owned mine two months from Home Depot, the install was a nightmare and now due to a poor design flaw, if you miss loose coins or anything in pockets it will get trapped between the drum and the tub causing rattling and noise during spin cycle. Guess what? Service calls EACH time this happens. This is nothing more than a $750 piece of junk. I feel like its marring the whole feel of my new house. I hate hate hate this washer and am trying to get Home Depot to take it back, Maytag to refund me or sell it at a huge loss. This is NOT getting anything you pay for and I vow to NEVER EVER buy Maytag again.

I paid $958 + tax for a Maytag Bravos washing machine in August 2008. I live by myself, so the machine is not overused. Nevertheless, it began to sound like a jet airplane during the spin cycle. And then in May of 2012, it failed with error code F51, catastrophic failure. The machine was not even four years old. I called a certified Maytag repairman. In less than 5 minutes, he told me the cost to repair would be about $900, and then he charged $115 for the service call! A call to Maytag resulted in Im sorry, there is nothing we can do.

We updated our 25 years old dishwasher, which ironically still worked, to a Maytag we bought at a BrandsMart in GA in November 2010. Sixteen months later, the unit just died. The panel would light up, but would not run. We contacted Maytag and were assigned a repairman (The Appliance Guy) who could not come to fix the dishwasher until 5 days later. Once he finally showed up, I was informed by him that the control panel for the dishwasher had two shorts in it and it would be cheaper for me to just buy a new dishwasher because the repair to this one would be $344.44. When I contacted the customer service for Maytag, they offered to let me pay for the repairs and then they would give me a six month service warranty for free. Does that make sense to anyone? I could buy a totally different brand, brand-spanking-new and have a twelve month warranty with a better product. I asked to speak with Cheris boss and got to speak with Aaron, who offered me the same spiel. Heavily scripted, I apologize that you are dissatisfied, but all we can do is give you the service warranty for six months after you pay for the repair. I asked him if he was reading a script and he replied no. Now I know that he had probably repeated these same words twenty times a day. Heres a thought, Maytag claims to be a green company, using less electricity and water, and saving the customers money and yet they are filling up all the landfills with these appliances that are not even five years old. How is that being a green company?You know how when you buy a nice new button-up shirt? The makers of that good quality shirt go ahead and sew an extra button on the inside bottom part of the shirt because they know that theres a chance youll lose a button. Well, Im thinking that Maytag should just start shipping a couple extra control panels in every box of Maytag dishwashers. Crazy idea, right? Okay, so an easier and cheaper way for Maytag to correct the problem is to stop making dishwashers. Go back to the drawing board, make the engineer who designed the control panel wash everyones dishes (as punishment and he can get help from the customer service people because theyre really doing nothing), start building the old design dishwasher that has the old switch and dial, and start respecting their customers. There, problems solved!

Bravos washer is 4 years old. Started making an extreme amount of noise during the spin cycle. Had a repairman look at and showed me the bearings and area under the tub. $400 plus in damage due to bad bearings, rust to bottom of tub and surrounding area. Four years for a high-end washer is pretty bad. Needless to say, I will buy a new unit and would NEVER recommend a Maytag Bravos appliance.

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

Dishwasher (MDB7709AWB2) stopped running mid-cycle, internet search revealed that control panel needs replacement at a cost of $135. excluding labor, for a dishwasher that originally cost $348. Notified Maytag and am awaiting a response.

In August of 2009, we had an opportunity to remodel our kitchen plus add new windows and doors. How exciting! SO we had put down new flooring in our kitchen that matched our oak cabinets and since we had a little money saved, we wanted to purchase new appliances to match. We purchased a Maytag side by side with ice and water in the door. It also had the fingerprint resistant stuff on the outside. It cost about $1300. You buy name brand so they will last a while but here we are November 12, 2014, 7 years later and the compressor goes out. If repaired, it will cost $8090 to fix. Why do I want another Maytag. I got a citation I bought in 1978 and it still runs. Hello Facebook, you will my next visitor.

Bought a new home in July of 2016 and the builder had included a Maytag Bravos XL washer and dryer. They are THE WORST performing appliances I have ever used! I will replace as soon as I have the means to do so. DO NOT PURCHASE the Maytag Bravos XL appliances. The engineers that designed them should be fired! The washing machine makes an incredibly loud noise (like an old starter grinding in a 50s car). Im told that this is normal for the machine. Does NOT clean well and leaves soap spots on dark clothes... leaves them on light clothes but I cannot see them. Whites come out dingy even with bleach. The tub is so deep that I have to use tongs to get out smaller items, I am 53 tall and have never had this issue before. Soap dispenser drawer wont stay closed during wash cycle. Clothes are so badly tangled during the wash cycle that it is hard to describe the wrinkled mess that has to go into the dryer.Dryer issues: Very loud. Very wobbly and unstable, and yes, it has been leveled 3 times. Bed linens have to be separated at least 3 times during the drying cycles because they twist and wad up into big, wet knots of cloth. Infuriating!!! Dry time is very long unless you wish to cook your clothes. So disappointed in this product. Total rubbish!!

I purchased Maytag fridge a year ago and it has been a nightmare. The freezer doesnt freeze items. the drawers were all damaged upon receiving. I have contacted Maytag for more than 10 times and 5 techs came that I paid 125 each visit to fix the fridge because I didnt purchase the warranty thinking it was a good product . It is not! They dont stand behind their word. They lie and they send unqualified techs the misdiagnose issue to collect service calls. Please avoid this brand by all cost. My experience is terrible and I never want to wish it on anyone.

I purchased a Maytag dishwasher in March 2005. About every 8 to 12 months since Ive owned it, the control panel malfunctions and needs to be replaced. I was told by the repairmen (similar to the many other postings below) that the malfunction is due to a faulty design where warm moisture shorts out the electronic control panel. For a few years, I paid for a service contract. But this seemed quite unfair, given the regularity of the same malfunction. Given that this is such a common problem, isnt there some responsibility by Maytag? This is clearly a faulty design. What about the legal responsibility for a recall? Is it possible that, together with other aggrieved owners, a lawsuit against Maytag would be the appropriate action?

25 months ago, I bought a brand new Maytag stainless steel microwave. We had upgraded all of our appliances except the microwave when we moved in our home. Our first purchase was the Maytag refrigerator. Should have learned my lesson from that because after less than a year, the freezer on the bottom went out twice! We bought this new microwave to replace an old one that didnt match the other appliances and was worn out. Two months ago, the code SE started appearing and then would go away after a few minutes. Now it doesnt go away and you cant use the microwave. I finally called a repair person since its out of warranty and was told that it would cost over $300 to fix it. Really! Im so angry because now I have to take money. I dont have to replace a microwave that should have another few years of use. Nothing at all reliable about a Maytag. I doubt Ill buy anything else they make.

IT A GOOD DISHWASHER, BUT I HAVE HAD 2 PROBLEMS WITH THE CONTROLS AND HAD THE CONTROL PANEL REPLACED. TWICE. The insurance I bought with the machine, sent me a jerk to fix it, I complained and they sent a good repairman.

My wife told me yesterday she was getting a f51 code... went on you tube and took the top off and the clothes holder out, found 1 quarter and 3 dimes... put it all back together... same thing... took the back off... hoses off, unplugged it and the allen that holds the motor had backed out... no more maytags for me... Tightened the allen, all is fine for now... my opinion, this should never ever happen... No lock washer anything engineering to prevent this from occurring... My grade: replace the engineer...

We purchased a $700 Maytag range 2 years ago and recently the oven did not work. After a Maytag authorized tech came out and checked the unit, he proclaimed the circuit board was bad and needed to be replaced. Since these ovens only have a 1-year warranty - regardless of the price you pay - he said it would be over $450 to repair it. When I asked why so expensive, he stated that they dont price the parts - Maytag does. I decided I could buy a new range for that price and get one with a warranty so I passed. I then decided to contact Maytag because I was very disappointed that such a reputable brand would prove so faulty. After writing a very polite letter and emailing customer service, they replied with a pack of lies. They stated that they have no control in what the service company charges for parts and failed to offer any assistance. They did not offer any solution except to say, Sorry. Well, you can bet that I have already spread the word to all my friends and associates about this experience and my Facebook page lit up with comments after I posted it. I will never buy another Maytag product and will make it my mission to spread the word. I had a similar issue with my brand new HP laptop but after contacting them, they immediately reached out to me and offered to pay for part of the repair!! Thats how you take care of your customers.

Maytag Bravos Series 300 - I bought this machine less than a year ago. There is an awful smell coming from the machine that I never smelled from any other washer I have owned. The clothes do not look, feel or smell clean, and my towels are ripped. It is an extra large washer, yet when blankets are put in the machine bounces and shifts. After reading all the reviews, it seems I am not alone in my concern with a machine that was not only expensive, but was told it is a great product. Maytag needs to do the right thing and recall this machine.

I purchased this $857 dishwasher from Lowes in May, 2021. It broke in June, 2021. S&S Repair was sent by Maytag to repair. It took 3 weeks for them to come, then they discovered the motor and pump assembly had gone out. Parts were on backorder. It is now August, 13, 2021 and I still have no dishwasher. Lowes would not replace this dishwasher. Maytag will not authorize a return. This is disgusting.

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

Maytag Bravos XL - I have always loved Maytag and never had any problems. In Feb we did some major remodeling with new flooring in our laundry room. Decided to buy a brand new washer and dryer even though our 10-year old Maytag washer and dryer worked perfectly fine. After looking at Home Depot and Lowes we first settled for a Samsung W & D but before it was delivered we shopped some more. After doing some inquiring we decided that we wanted to stick to a long trusted W & D line so we chose this washing mashing and matching dryer. From day one I decided I did not care for it. I found if I put too many clothes in that they did not come out clean. Any dark pants would come out with what looked to be soap or softener stains and would have to rewash 1 or 2 times. Now I can only put in about 4 pairs of pants to wash. I have been cleaning it once a month as the manual says to do but yesterday I noticed a terrible odor coming for the washer. I could smell it out in the hall. I did the cleaning again but still smell it. Now after searching the internet I find a video that shows the problem is mold under the drum. No amount of Affresh or bleach is going to clean something UNDER the drum. It is not my job to have to take this apart every few months and clean out mold and moldy water. Sounds like this problem has been going on for a few years and this should have been fixed long before this. I wish I had my old faithful washer and dryer back. Maybe I should have stuck to the Samsung washer and dryer.

We purchased a Maytag refrigerator and right away had a loud noise. Found out the ice maker was on even though we dont have it hooked up. Now our freezer isnt working. Food is defrosting and ruined. Bottom half of refrigerator is freezing everything. Our fruit and pop and water and lettuce all frozen. 4th time they came which is today. Now says our freon is low so well see what happens. The repairman was so rude he was yelling. We said our Popsicles turned to slush so he said, Dont buy any. He was so nasty. No more Maytag for us – waste of money. Even had the compressor replaced. Wasted 1100.00.

Quiet, well priced and reliable technology which makes owning this dishwasher an easy buying and owning experience. Having the brand backed with great reliability and if needed excellent service makes the buying decision easy for the consumer.

We bought a Maytag refrigerator less than two years ago because... its Maytag. Less than a year later we had five service calls. The refrigerator wasnt cold, the freezer was the temperature of the refrigerator and it took two months and two different repair companies to fix it. And now... yes, the same problem seems to be occurring. It was a leak that was supposed fix. Cant bear the idea of going through this all over again. NEVER again Maytag!!!

I like my fridge. Its a old one and still works. Its been very reliable and have never had a problem with. I dont think I would ever purchase a different brand for Maytag is the brand for me. They last for years.

The washer is so loud it can be heard all over my home (my home is 2700 sq.). It sounds like metal to metal grinding. I was told thats how the run and the first bit of water isnt enough to even wet the clothes. Id never buy another one (even though this is my 3rd Maytag washer. Im 78 yrs.old).

The Maytag Bravos washing machine (Model No. MVWB75OWQ1 Type 580) is the worst Ive ever owned. The low water level obviously is not sufficient to clean the clothes as the clothes come out still dirty. I pre-treat stains carefully and follow all of the directions and 9 times out of 10, my clothes come out with the stain still there. The clothes never smell clean. In fact, they have an odor. My t-shirts still have a smell of BO under the arms and some of my clothes still smell like my perfume. They just arent clean. I feel like we put our dirty clothes in this machine and they agitate around in a little pool of water for an hour and they come out still dirty. The machine frequently gets off balance and shuts down too. If I had the money to trash this one and go buy another one - Id do it in a heartbeat. Unfortunately - Im stuck with this piece of junk until I can afford to buy a new one. This was a total waste of money and Maytag should be ashamed that they have not recalled it and given its customers a replacement option.

Dissatisfied with the poor performance of the Deep Water cycle of Maytag Model #MVWX655DW0. Cycle produces low water thereby resulting in inadequate cleaning of clothes. Choosing another cycle to wash a particular load doesnt match what is recommended.

Maytag French Door Refrigerator (Counter depth) #MFC2061KES14 which cost over $2,500 dollars is a DUD and the company is EVIL. The freezer leaks all over the floor and the company will not stand by their product. When I called the company they said they have had to upgrade a part called the drain tube kit because of this problem but did not put a recall. They know that this problem will occur just about the time the warranty runs out. I bet the wife of the CEO of this company has a very expensive good brand of refrigerator. Stand by your product and pay for the repairs and labor to get it fixed and put out a recall. LIFE IN AMERICA!!!

I bought the Maytag Bravos Series 300 Dryer in 2009. In September 2011, the dryer wont start. I called Maytag. They basically said were on our own. It only lasted two years. What happened to appliances that lasted 10 years? I will never buy a Maytag dryer again.

The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

Wish I would have read the many, many, many reviews on the Maytag MDB8959SBS dishwasher before buying it. As noted by others, the touch control buttons stopped working 1 month after the 1 year warranty expired and Maytag wont do anything about it. BE WARY OF THE 10 YEAR WARRANTY CLAIM - IT DOESNT COVER THIS PROBLEM. Maytag should issue a recall on this product and do the right thing - take care of customers like they used to.

Shortly after purchasing my Maytag refrigerator had to pay for a new motor in the ice maker. The cover for the lower large food tray broke. Now approx. 4 years later am getting ice build-up on the bottom of the lower freezer unit, about one-half inch thick. It is enough so the freezer door wont seal when it closes and the inside builds up with frost. Not happy with Maytag or this refrigerator.

After purchasing this washer in 2007, the washer started to smell like sewage. At first we werent sure it was the washer and had a company come out to check the pipes. After this and calling Maytag complaining without any luck. We were told to buy affresh tablets and run it through the washer once a month. This last only so long and the smell comes back. Now when the washer goes into the spin cycle it sounds horrible. Again called Maytag without getting any resolve. I will never buy a Maytag again!

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

The machine runs and runs and runs and still the clothes come out dirty. Clothes are often not even wet all over. The Maytag HE water-saving washer is a terrible Hoax. The dryer also is faulty. It rolls the clothes into a big, undried ball of dirty clothes.

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

My Maytag Series 300 Dishwasher would not start. I read the reviews and took the door off (easy if you have the right tool), removed the control panel box (one screw), and cleaned the ribbon with electronic cleaner as per someones suggestion. It started right up. This is a bad design. Would I buy another Maytag? - No way! We will see how long this lasts. There is no seal on the door to keep out humidity. Do we really need a new control panel? When this is done...I am done with Maytag!

We have had this refrigerator, model MFI2665XEM7, less than two years. The ice maker stopped working and we had it replaced at least 6 times in a two month period. We had a solid ice sheet in the bottom of the freezer drawer and it leaks water on the floor constantly! Even today... after another ice maker replacement, we have no ice! I never wanted a Maytag, but finances and the small space we had gave us little choice. I am not sure what our next move is. I will NEVER buy a Maytag product again! I should have google this sooner and we could have saved the poor repairman all of those trips!

I bought a pair of Maytag washer MVWB700BW and dryer YMEDB700BW in November 2014 from Home Depot and the washer was never washed cleaned from the 1st load! The detergent was stuck to the clothes. I tried different cycles and the result was the same. I called Whirlpool and they sent 2 different technicians to check. I showed the technicians the clothes. They both admitted there was no technical problems but the washer performed badly. The 2nd technician even took pictures and attached to the report he sent back to Whirlpool. Still Whirlpool refused to take back the pair or exchange to another model. I went back to Home Depot. Home Depot said they talked to Whirlpool but Whirlpool refused to refund me. Home Depot finally agreed to take back the pair and allowed me to exchange to another pair of a different brand but I was charged a 15% restocking fee. Whirlpool said the machine was working properly yet it was never even met its basic requirement of a clean load! Still they refused to take this pair back and refund me the money! Now I had to pay a 15% restocking fee to get an exchange. I will never buy anything from Whirlpool/Maytag and I will not recommend this brand to my family or friends!

I got a washer from a Menards Store in Fond du Lac, WI. I was given a line of crap at how great it was, and because Ive used Maytag for years I bought it. Id rather have my 20 plus old one back. At least it didnt take over an hour for a load, and the rinse cycle really worked. WE HATE YOUR NEW WASHER. As soon as we can afford a different washer well be looking for a different brand.

I have never been so disappointed in purchasing an appliance for my home. The Maytag Bravo XL large capacity top loader, has never worked properly, and I have many ruined pieces of clothing. Although it has a very large capacity, the water barely fills to a 1/4, and clothes are sticking out of the water, while they are supposed to be submerged/being washed IN the water. Clothes come out of the washer smelling foul. WORST WASHING MACHINE EVER.

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

We bought our Maytag washer and dryer a bit over 5 years ago. Now the UL warning comes on. Found out it will be over $400 to fix it. It only cost $500 new. Repairman says it is very common and not to pay him to fix it. Our GE went 20 years. Lesson learned, wife is out looking at new GE.

Our Maytag lint trap started falling apart a few months after we received it. Call Customer Service to get a replacement due to the product being faulty. The answer that I got from Customer Service: We sell you a new one. Poor customer service, faulty product. Dont buy dryer from Maytag.