Freezer does not freeze well. Causes most our food to get freezer burned. We tried turning it up and down but made no difference. Actually went and bought a separate freezer for meats.

I have a 7-year -old Maytag dishwasher, which was not working well. I paid over $600 for extra features. Maytag contacted me that the coil had to be replaced. They sent it to me, but the repair service said that theyve sent the wrong one. When they sent the second one, the repair service came out and called Maytag, They said that my model cannot be recalled. The repair service left, and after 1/2 hour later, Maytag called me and said that the repair man has to come back and install a new coil. He came back and installed it.

I have always hated soft touch control panels so I purchased a Maytag Dishwasher with old style push buttons. IT DID NOT CLEAN THE DISHES, so Lowes took it back and I was convinced to UPGRADE to an MDB7749SBB0 and was told this machine was top of the line, although it was VERY temperamental from the start. I guess I should have done my homework. I see now several complaints about the control panels not working. I was told that MAYTAG was a very reputable company and that they stand behind their product. WRONG!. The company KNOWS these panels have problems and should replace them free of charge as it is obviously a defect. Nope, first they offer to send someone out (In a week) to repair it at $80 just to look at it and the panel is over $100 to replace, and when I complained they tried to sell me extra coverage for $250. REALLY? What is the purpose of purchasing a QUALITY dishwasher? I might as well purchase a cheap dishwasher and replace it when it breaks. I think you should be responsible for your product when you have several complaints on a specific part.

We purchased this product from Lowe’s in 2009. We liked it for the first 6 months. Then it started putting holes in our clothes, the washer smells bad, coins get stuck, and make noise. Something needs to be done because there are thousands of upset consumers out there, all with the same complaints and Maytag does nothing. It’s not Lowe’s fault. They didnt make the washer. Read all of the complaints here.

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.

The first problem happened a month after we bought the horrible product. I had biscuits baking in the oven and the oven door locked itself like when in self-clean mode. Maytag sent out a repairman that had the part in his truck because they knew there was a problem with that models door. I pointed out that the door does not shut properly, causing inaccurate heating and scorching on the outside of the oven door. The repairman insisted that it was shut properly, and that it was designed at the angle the door sits. He replaced the scorched part of the door, but it immediately scorched again. I have had the part replaced 3 times, and will not do so again until we sell the house. I have spent over money over and over again to make the repair, because it makes the stove look like it is filthy with grease. Now, all the dots painted on the glass top are coming off, and the remaining black glass behind it also looks like burnt grease. It is so embarrassing when entertaining; but the stove is clean. I spent a lot of money for this, and it has been junk from day one. Avoid purchasing.

I can honestly say that my Maytag refrigerator is indeed the worse appliance that I have ever purchased. This is how it rolled... I bought a new Maytag stove, frig, microwave, and dishwasher in June of 2006. Here is what I am now dealing with... the frig went on the fritz 2 years ago (warranty expired). The problem being the freezer would not automatically defrost. Because of this the coils would ice up and this prevented the cold air from moving from the freezer into the frig part. Things remained frozen in the freezer, but everything became warm on the other side, the frig side. I had it repaired about a year and a half ago to the tune of $165. Then about 6 months ago the problem reoccurred, but instead of paying for another repair I figured out that if I used my blow dryer I could defrost the ice from the coils on my own.Unfortunately, the problem reoccurs more frequently now and I have to manually defrost the coils almost every week. This past weekend things finally came to an end as no matter how many times I manually defrosted the coils, it would be fully iced up again with an hour or so. Also, all the time it is acting up it just sucks up electricity, and I have notice a spike upwards on my energy bill. It must be related to the frig. So, I bit the bullet and bought a used frig on craigslist just to hold me over until I have time to do research on what appliance brand is indeed reliable. I should of done this before I bought my Maytag appliances from Home Depot. As far as my other Maytag appliances, here is their current condition. Microwave about the stove: the handle broke off a little less than 2 years after purchase. Stove: now has rust on the front of stove, at the bottom of the stove which is a pull out drawer.Dishwasher: not working at all. The start button doesnt work. Normally, you just push the button and a green light comes on and it begins the first cycle. This is no longer happening and no green light comes on. Refrigerator: Took it to the dumps this morning to be recycled. Cant believe it, all of these appliances are nothing but crap and I will never purchase another Maytag. I have shared my experiences with all my family and friends and have encouraged them to avoid Maytag, as it is not even close to being the product it used to be. Another piece of junk coming from somewhere other than here in the USA. We lose jobs here in the US, and then end up buying the goods from another country that makes inferior products. How stupid can we get!

I hate my new Maytag washer and wish I had never purchased it. Theres no way to control the water level in it, and on sensor mode, the clothes are barely wet and rubbing against each other creating wear. Things come out with soap stains and twisted up so tight that I dont believe water got close enough to the dirt to carry it away. Dont waste your money.

I have just inquired on this site about problems with Maytag dishwashers. Ours does not start. It is about a year old and is Model MDBH989AW03. I am very discouraged after reading the many continual problems with control panels. I am checking my warranty. If it is out of warranty, we think that we will purchase a GE that has worked great in our other house.

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

I bought this washer in November of 2012 thinking it’s one of the best because it is a Maytag. Five months later, the wash machine needed a new gear case because it was making this horrible loud noise when it was washing and spinning. The service guy came over and replaced this part. Now, the washer does not want to spin. The clothes are soaked, and I have to stand there and manually turn the knob to spin it; and it still doesnt spin right. This is the worst experience I’ve ever had with a washing machine, and I regret ever buying this Maytag. They should recall this series of washers because there is something really wrong when you have to have it repaired twice, and it is not even a year old!

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

I purchased Maytag washer/dryer set in Feb 2021. In June the washer broke. It took 2 weeks to get repair person to look at it. During the appt no faulty product was identified so they dont know what to replace. No parts were available. A follow-up appt was set for 1 month later. No parts are available to make the repair so a follow-up appt would be futile. . The only communications other than No Parts is that they want me to purchased an extended warranty. I will never purchase another Maytag product or recommend them to anyone. Meanwhile my warranty continues to time-out and they dont have any parts or idea when they will be available. Im not sure how a company can sell products that they do not have some level of support for those products. Beware of purchasing Maytag Products.

Overall I am satisfied with my Maytag Model MDB8859AWW2. I purchased the dishwasher 06/05/201. However, the door spring squeaks. It is a grating sound.

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

I bought a Maytag dishwasher in April 2012. The electronic control panel failed in October 2013. Repair quote was $250, and there is no guarantee that the new control panel will not suffer the same consequences. My research has revealed that this is a very common problem with the dishwasher experienced by a large amount of owners, all about at the 18-month mark. I contacted the company and was chastised for not purchasing the extended warranty and was basically told, Too bad so sad. Buyer beware, do your research before you purchase this appliance. I will never buy a Maytag appliance, or any brand associated with the Maytag name.

Bought a Maytag fridge model MFI2569YEM0 a few years ago. From the get-go, the ice machine would spit out ice hither and thither, mostly not into the cup or mug. Even when I held the cup up high into the dispenser orifice, I noticed it still spit out ice seconds after I released the cup, so ice cubes would spill onto the floor. Secondly, the vertical doors do not close well, and I must manually push them closed, especially the left door due to the poor design. (I noticed my neighbors more updated fridge has a better closing door. Forgot what brand, though.) Theres also rust forming on the front of the stainless steel fridge panel. It has penetrated through so I am unable to remove it.Lastly, this past week I walked into the kitchen stepping in a pool of water in front of the fridge. There was a sheet of ice accumulated on the bottom of the freezer. After some research, its likely the nipple in the back of the fridge that plugged up. I have yet to fix the problem, but so far, Maytag gets an F- in quality, and I will NEVER, EVER purchase any of their appliances again. I remember my parents washer dryer lasting 30+ years. Maytag, what happened???!!!

I purchase my Maytag Bravos washer from Sears in May 2011. In February of 2014, I started to get the UL message, meaning unbalanced load. I would re distribute the clothes and sometimes that did the trick and others not so much. Now every load comes up UL. I tried putting the machine on the drain and spin cycle to at least get the clothes a little bit drier but the UL message still appears and the clothes are still soaking wet. I lifted the washer up and there is an oil/grease type spin pattern under the washing machine. I called Maytag today (which is now Whirlpool I guess) as the washer has a 10 year warranty on the drum and motor. I was told a service call is $129. When I mentioned that I had Googled the product and saw many reviews with the same exact problem, she stated the Bravos has no common complaints. From what Ive read, it seems to me it would be more cost effective to go out and buy a new washing machine and it obviously wont be another Maytag or Whirlpool.

IT A GOOD DISHWASHER, BUT I HAVE HAD 2 PROBLEMS WITH THE CONTROLS AND HAD THE CONTROL PANEL REPLACED. TWICE. The insurance I bought with the machine, sent me a jerk to fix it, I complained and they sent a good repairman.

I have had trouble since I bought the Maytag Bravo washer. It first started out with the motherboard putting up crazy numbers. It took 2 different motherboards before that problem was fixed. Then it started with not wanting to drain; that was caused from the washer machine sucking up small clothes items in the drain plug. I had to call the Maytag repairman 4 times until I was told I had to put the small items in a laundry bag for this to stop. Now it is going off level on every wash, even when it has only 2 pieces of clothes in the machine. I am about ready to throw it out. Btw, all of my appliances are Maytag and I will never buy another Maytag appliance again or I will never recommend a Maytag to anyone.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

Maytag Bravos XL washer and dryer. Best washer and dryer I have ever owned. I have owned about every major brand and these are by far the best. My husband is a hog farmer and the washer does a great job. I will always purchase Maytag appliances.

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

I bought a Maytag dishwasher, stove and refrigerator and the dishwasher was a problem from the beginning. Repaired out twice and replaced the control panel. Seasonal residence, so the start of year 2 (this week) the control panel goes a third time. Its going to cost $387 to repair (told my elderly mother) and it turns out it was a warranty program that she purchased, not a repair estimate. She was misled as she called Maytag and they transferred her to a warranty company, and once again Maytag says theres nothing they will do. Now, Im hassled with cancelling that as well. I called Maytag and they dont stand behind their lemon of a product and said there is nothing they can do because its out of warranty (even though theyve been out twice to fix it). Do not buy a Maytag product. This is the first complaint Ive every written and I am just shocked that Maytag doesnt stand behind their product. Im informing 100s of people to not purchase Maytag and they will pass along my negative experience as well, for that, I am sure.

We purchased a Maytag washer model MVWC400XWO almost 2 years ago and it has problems with the bearings and the whole computer board is defective. I was told to buy the extended warranty for $350, which we did. As of today, we were told by extended warranty they are refunding our money because there are so many things wrong with this washer, including the whole computer board, that it would cost them too much to fix or replace it. Im in complete shock. We paid well over $500 and are still making payments on it. I spent the day reading hundreds of reviews from people with these exact same problems and Maytag is aware of it and will not help. They should not be selling these anymore. Im completely sick to my stomach. I cant afford another washer and when I called Maytag, they said it was past the year and we are out of luck. I cant believe this can happen to people and they get away with it. A washer should last longer than 2 yrs.There are hundreds of people going through this with Maytag and no one will help.

Control panel start button failed 55 weeks after purchase and installation. Model no. MDB4709PAW. Repair costs for labor and part totaled $298. I have since found out that Maytag dishwashers with this type of control panel are faulty and fail often within first 3 years. Purchased at Johnnies Appliance, Glendora on 6/14/14 NJ; ticket no. **.

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

We bought this Maytag washer 3 mo. ago and now need work done on it. We were told that they could not find anyone willing to come work in this area. We live in the Mississippi Delta, 30 miles so. of Greenville, 50 miles no. of Vicksburg or 90 miles from Jackson. So I guess the Maytag repairman is not just lonely anymore, he doesnt exist.

I bought a new Maytag refrigerator 5 years ago and it has been nothing but a headache. Ive spent more than $700 getting it repaired. The Maytag repairman is no longer lonely, hes really busy. These units are crap and the company does not stand behind their products.

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

Almost two years after purchasing the Maytag Bravo XL, I am fed up. I have the exact same problems as everyone else in these reviews. Soap scum left on dark clothes since day 1. I thought maybe I was doing something wrong. I have read and re-read the manual especially the troubleshooting guide and still have the same thing happen. Its very frustrating. I constantly have to re-rinse clothes because of soap, lint, dirt, etc left on clothes. I wouldnt give away this washer to anyone, I would rather burn it. I am currently looking for a new washer, the last one I had for 11 years was a front loading Whirlpool. I should have stuck with a Whirlpool, I still have the matching dryer no problems at all.

Was very happy with choice when it arrived. Bought October of 2010. Now, this summer, nothing but problems. Honestly weekly cleaning of vents underneath, sheets of ice in freezer, refrigerator not staying cool, constant frost plugging areas, and no more ideas of how to make it work. I already quit with Kenmore after terrible problems with their appliances and now when Maytag doesnt stand up for years what are we supposed to buy? OUTRAGED with American quality of products and disposables. UGH!!!

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

Maytag is a product that I would buy any time. Even uses it well last for a long time. If you want to spend money this is a good investment for your kitchen and as for your laundry get the washer and dryer. You do get your moneys worth with Maytag.

As many other reviewers have mentioned there is a defective control panel in the Maytag Dishwasher series MDB 7749. I too purchased this model at Home Depot and did not buy the extended warranty. The serviceman indicated that this model is known for its defect yet Whirlpool who owns Maytag does not have it on its recall list. I wrote to the President twice in Sept. 2017 without the courtesy of a response and now learn that he retired effective Oct.1. Is there no-one to answer his emails or is it more likely they really dont care. Sears just dropped them and who knows where their new president will lead this company. Be aware that this model dishwasher is defective and they wont replace the control panel. Too bad as once Maytag before Whirlpool bought them out, was a good and honorable company.

The top of the range has blistered and has worn off. It cannot be cleaned. I spoke to a Maytag representative and was told to try and use magic eraser to clean around the burners. This did not work. The model number is mgr7775xs. Is there any solution to this problem. My range looks terrible.

Our Maytag refrigerator was about a year old when we noticed rust on the edge of the stainless steel doors. I called Maytag and they were nice enough to replace the doors even though the warranty had expired by their standards. Keep in mind, the warranty starts when you purchase the product, not when you install it. We ordered our appliances from Lowes well in advance of our kitchen remodel so we would have them when we needed them. The time our appliances sat in Lowes warehouse used up two months of our warranty.Now, the new stainless steel doors are rusting and they are refusing to do any thing about it. Should stainless steel rust? Maytag doesnt seem to care whether their product performs the way they should. Its all about the warranty. Once the warranty lapses, they could care less whether their product blows up. Thats the customers problem. Whatever happened to building a quality product that lasted and customers bought for generations? Obviously, thats a thing of the past.My goal in writing this is to make consumers aware of appliance warranties. When I spoke to Lucas, a Maytag customer service supervisor, he informed me their products offered no warranty on the finish of the product. So, according to Lucas, the finish on your brand new Maytag appliance could flake off like dandruff and its your problem regardless whether its a manufacturing defect or not. Remember, buyer beware!

Failed after only 13 months with light use. I have a Whirlpool extended warranty which I had to fight to get them to honor. Then someone came to fix my washer and needed part was ordered, but part isnt available and company wont tell me when it will be. I have received 6 part availability dates so far. Whirlpool wont help. Over two months now without a washer. Ive asked them to replace machine or give me my money back, but they refused. The Whirlpool Extended Warranty group doesnt answer their phones, was put on hold for a long period.

Ive been a Maytag consumer since 1980. I bought washer, dryer, refrigerator and a smooth top oven. I replaced the washer and dryer with the Bravos series on November 22, 2011. Everything was fine until 6 weeks ago. The bearing went bad under the drum. 2 techs and 2 weeks later, at the cost of $527 and change spent on repair for a $650.00 machine, I started to look into reviews. Not! Can you say class action lawsuit! The fine gentlemen informed me 5 years ago about the Canada buyout, a local retailer that only sold Maytags. He shut his doors due to the fact that he will not work on junk! Oh well, he was right. 13 months worth of use and Im going to spend that kind of money. Now I understand why the repairman in the commercials retired! Shame on you. Love, crazy Mike.

I purchased a white Maytag gas stove over 12 years ago. It has been great and never caused any problems. I live alone and rarely use the oven. However, I use the stovetop daily for cooking. With continual use, it has a lot of nicks and scratches. It also has stains inside the glass oven panel that I cant clean. The glass would have to be removed in order to clean inside. This is why I give a rating of 4 stars. If I used the oven more frequently, I would notice if it had any problems with the temperature, proper cooking, etc. and could give a more accurate rating. I have small toaster oven and therefore, I cook practically all of my meals in the toaster oven.

I have always bought Maytag and never had a problem except with this new washer. Our clothes smell like dirty laundry and when done washing there is lint in the creases or folds of the clothes. I am using a product for cleaning the washer each month, but our clothes still have an odor. I do not like the way the washer works, it just moves back and forth slowly, but the clothes dont circulate enough.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

This machine is the worst! I purchased this Maytag washer 2 years ago and the machine leaks from the left side bottom. I called Maytag and they said I need one of the techs out to check the machine and the cost was going to be $115 so I agreed even though was not too happy that there is no guarantee after 2 years. The service tech arrived. He could not move the machine himself and was a little angry so my wife called a neighbor to give the tech a hand after looking at the machine. He called if office to help him diagnose the unit and said the drum seal was bad and it would cost $315.00 so my wife agreed but at the end of the transaction my wife asked the technician, Is it guaranteed that this would fix it? He replied there is no guarantee but we still have to pay to try... What kind of diagnostic is this, Im very unhappy with this company. 1st the machine sucks after 2 years to start leaking and 2nd their service dept. sucks also... stay away from Maytag.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is already in the junk yard, the drive system failed, the bearings failed and it began to leak. The dryer had a main control board failed, I was able to purchase a new one and replace it myself. The board was made in China, the machines were assembled in Mexico. I replaced the washer with a heavy duty Speed Queen washer made in the USA!

We bought a brand new Maytag refrigerator online model # MSD2660KES and it arrived dead. The first Maytag tech that was sent said he does not recommend us fixing the problem because refrigerant leaking will happen every few years. We were not able to return the refrigerator, so we opted to let Maytag fix it. Here we are 2 years later and sure enough, the refrigerator has stopped cooling. We are out of warranty period, so the service call cost us $65.00. The tech told us this time its the compressor and replacement would cost $650.00 to fix. We are not wasting any more money on this piece of junk.

This refrigerator has been my worst nightmare come true. Everything existent freezes: salads, tomatoes, berries, cherries, milk, water, etc. Never again will I purchase a Maytag product. Service is non-existent.

This is about my model MFI2569VEB2 refrigerator. It has French doors with bottom pull-out freezer, refrigerator door ice and filtered water dispenser. The delivery person installed the fridge and took off outside plastic and left inside plastic in. It froze everything until I took out the inside plastic. Within the first year, water started shooting out of the top of the fridge. A rubber connector for the icemaker, which was on top of the fridge, had broken. Within 18 months, it freezes everything in the refrigerator, even on the warmest setting. I have to leave it unplugged each night. The icemaker gets big chunks of ice stuck to it and wont let ice out. On top of all of that, the water from the fridge door pours out extremely slowly, this just how they are built.I will have to fix the thing myself and eat the expenses, so to speak. I bought the Maytag because Samsung had poor reviews. No matter how fancy you want your refrigerator to be, and how nice you want it to look in your kitchen, stick to the basics. The fewer bells and whistles, the more reliable.

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

Maytag dishwasher model MDB4949SDE3: This dishwasher is the biggest POS that I have ever owned in 40 years. The first one would never turn on and fill with water and after it finally did it leaked on my new floor. Waited 10 days to have it replaced. The dishwasher cycle is 2.5 - 3.5 hours and the dishes come out dirty. The top rack is not adjustable to wash odd things. I feel that these dishwashers need to be replaced.

Have had the top freezer Maytag refrigerator for several years now, and it has performed great. Exterior is easy to keep clean, and the interior shelves come out easy for washing. Three drawers for fruits, vegetables and meat/cheeses work out great, and keep those products at the correct temperatures. Settings for both freezer and refrigerator are easy to see and change, if needed. Would buy another Maytag unit. Easy slide out for cleaning coils behind the unit.

Bought Maytag dryer in December 2016. Worked fine for first 3 months. Then blue coloring showed up on back of drum and came off on white clothing. Had tech come out. He took pics and send to Maytag. They said it was normal. Further talks with customer service brought statements that we caused problem by drying blue jeans. Funny we never had. They just continued to say this discoloration was normal and we did something to cause problem and nothing they could do. But at least they were sorry for our problem. Whirlpool does not stand behind products. Dont buy.

I purchased a Maytag washer and dryer (Bravo series) in February 2011. The top edge of the drum in the washer is fraying. I contacted Maytag about the issue and never heard back. Now my dryer is not drying clothes. It feels like there is heat, but after 1 hour, the clothes are all hot and steamy, but still really wet. Our previous washer and dryer was over 10 years old and had no issues whatsoever, we just decided to upgrade to an HE W/D and now after just 14 months, the dryer doesnt work. They dont make them last anymore.

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

We have had this refrigerator (Maytag Side By Side Refrigerator with Ice Dispenser 27 CU) for 5 years this month and have already had to have it serviced once and now the ice dispenser just went out. I wish there was a brand out there that did not have problems and when problems occur, you do not get the runaround to get them fixed!

I will never buy a Maytag dishwasher again. I purchased it on 05/05/07 for $500.00. It’s quiet series 300 MDB6601AWQ. After 3 years of use, the control panel is completely dead. It was only working on one setting for the last year.

Purchased new stove from Home Depot. Was delivered damaged after I opened it. Called Maytag and they cannot get a service man there to look at it. They keep on telling me I have a 30 day unconditional warranty, yet they cannot live up to their words. Absolutely amazing. Bought the Maytag because of the 10 year warranty. Do not waste your time. Buy locally at an appliance store not big box stores. Do not buy Maytag either - service is just a bunch of well qualified talkers and key punchers. Very poor buying experience.

Weve had our Maytag dishwasher for less than 4 years when the control panel quit. The repairman came today. He was here 10 minutes and it cost us half as much as a new dishwasher. Its just the two of us and we use the dishwasher once every 4-5 days. Almost laughed when the repairman said the part and labor was under warranty for 90 days! There is no quality control anymore. Just greed.

Bought a brand new Maytag French Door Bottom Mount refrigerator in 2014 to simply upgrade to stainless steel. Put my old refrigerator that I have had for 17 years in the garage. Never EVER had an issue with it and it still runs perfectly. Well, just out of warranty in May of 2015, the ice maker stopped working in the new Maytag. Called and got service. Learned there was a recalled part. Service man fixed. 2 days later, it broke again. They came back out and fixed again. This time, the motor was REALLY LOUD. They came out to replace that. Now, both the freezer and refrigerator are not properly cooling. Cannot keep ice cream and cannot make ice. Called again. I was told these dual fan systems simply do not work. I am out of warranty and too bad for me. A wasted $2500!!!

The right front heating element works at the high position only. The over doors viewing glass is too fragile. It shattered while positioning the range. Otherwise, there are no other issues with electric range.

Our washer/dryer combination (2005 Maytag Neptune MLE2000AZW) has given us nothing but problems. The main problem is the stink from the washer. The unit is no longer usable and we are searching for a top loading unit to fit in the space. I am so angry - how did this piece of junk ever pass Maytags quality control?

Keep having the problem, the display panel tells me to close the door when the door is closed. I had a repairman repair it. 2 months later it started happening again. Im buy another microwave. It doesnt make sense to have it fixed again.

I have owned my Maytag washer for approximately five years. Ive always used the recommended detergent and religiously used the tabs to clean the machine when it was required. I have never abused the machine by overloading it, using too much detergent, etc. It is now coming up with an LF code. There is no one in this area who does repairs and if I do find someone Im sure theyll want some exorbitant amount to come all the way out to the boonies to give an estimate and the repairs Im sure will be hefty. I take very good care of all my appliances and expected this machine to last much longer.

I have had this machine for 15 years and never spent a penny on any maintenance, I love it. Some things are worth it and it still has a stylish look and cleans great. The only thing I would change is if it didn't have any the middle washer paddle so it would have more space like the newer models.

I purchase this dryer not even a year ago. It is not performing right. I call customer support and they willing to try something to see the problem. I hope I don’t have to pay anything out my pocket.

DO NOT BUY A MAYTAG BRAVOS MCT WASHING MACHINE!!! I have had the machine for two and half weeks, it HAS NOT WORKED EVEN ONCE!!! Service was scheduled - again for a BRAND NEW machine - through Maytag/Whirlpool - and the service ordered never happened. We waited an entire day, 8 am - 4 pm, only to discover the service desk of Maytag doesnt work either. My service is now booked for another week away and I am working on returning this AWFUL Maytag washing machine which never worked even one time!!! Warning: Do not buy Maytag/Whirlpool appliances!!

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.

Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

We purchased a Maytag Commercial Technology washer from Lowes. After having the washer for only 3 months, the drum failed, an entire load of clothes was turned black with oil, and my washer was out of service for months. The drum had to be replaced. They did not offer me a replacement. I was just without a washer. They couldnt get the parts because of supply issues created by Covid. I was offered a 2-year additional warranty which should have carried me through 2022. Last week, I called to use the warranty - service was scheduled (and I was told that I did indeed have a warranty by the service team.) I was then told by the repair team that I was out of warranty. Maytags notes show I was only offered a 1 year additional warranty. I talked with Management at Maytag/Whirlpool - they will do nothing for me. Shame on me for not getting that in writing. Shame on Whirlpool/Maytag for lying to me. The washer has been a nightmare! Dont buy one.

I bought a Maytag Top Loader. I soon discovered that it is not possible to do a cold water wash. After much communication with Maytag Customer Service it was determined that there is no way to bypass it. And it uses a lot of hot water, even on a cold wash. Their explanation was that the water needed to be a certain temperature to make the detergent work effectively. The same detergent that I’ve been using for 40 years with cold water in my Speed Queen. When I need to do a cold water wash, I go to my parents home and use their washer. Disappointing purchase, my last Maytag, for sure.

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

I have had my Maytag refrigerator for eight years and it is best one I have had in fifty years. It is dependable, quiet running and easy to maintain. The ice maker is wonderful; it always has ice ready even on the hottest summer day. If and when I ever need to purchase another refrigerator, I wouldnt hesitate to buy another Maytag!

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

The control panel acts just like the other reviews on here. The cancel light stays on. If I close the door, the washer automatically starts up again. It is unusable and it costs too much to have it repaired. First and last Maytag product for me.

We purchased our Maytag through Sears. We wanted a very basic machine, and thats what we found at Sears, yay! Fast forward eight years and it suddenly quit agitating. We tried fixing it ourselves by replacing a plastic gear part, which, later on our appliance technician said was totally logical, but it still wouldnt work. We got our appliance repairman out here and he took it into the shop and fixed the problem, which turned out to be part of the motor or something like that. The thing that bothers me the most is that he asked if we had bought a refurbished washer, but we hadnt, it was brand new. He gave us a part that was swapped out that wasnt made for the machine and also said the safety guard for the cord was missing. This keeps it from pulling out of the machine in case it gets jerked. I feel deceived and just wanted to vent because there really isnt anything I can do about it now. Buyer beware, yes, but I know we have to be our own technician sleuths to be sure were getting what we paid for?

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

This Maytag Centennial with commercial technology washer has ruined a couple of thousand of dollars of clothing, maybe 10 to 12 of my favorite shirts (ripped holes around the top of the pockets), bath towels and sheets and comforters and hand knitted small blankets that can never be replaced. It tore holes in nearly everything that was made out of cotton, I was doing spring cleaning and I normally wash most of my summer clothing, but this time this washing machine destroyed nearly all my summer clothing. This washing machine came with the house I just purchased. (I gave my older Maytag washer and dryer to some needy folks which worked great when I moved here). Disappointed in MAYTAG. Will never buy another Maytag!

Shame on Maytag! Customer Service is appalling! Paid 2500 for one of their top of the line refrigerator/freezer and had the repair people 5 times in one year. It was determined that it is a bad model number that Maytag wont recall but knows it is faulty. Started with ice build up in freezer making it sound like a plane taking off. It kept running trying to defrost (energy efficient-right). The repairman put in a request to have the product replaced based on symptoms and freezer being at 26 degrees. We had to wait five business days for Maytag to review it. I have a family and was having guests. They told me to buy a dorm refrigerator and they would send me a small credit towards it in 4 to 6 weeks. They finally agreed to replace the known faulty model, but I have to wait for the exchange team to contact me (2 weeks later). I keep calling and leaving messages but cant get the exchange team to even return my calls. I have my sons graduation this weekend and I dont have a freezer and my refrigerator is faulty with all my vegetables rotting within two days. It also took two days to originally get someone in management to call me back (even though it did no good - she cant help me). You cannot talk to management if you call customer service. They downright refuse! What a company!

I have never owned a Maytag in my life but was told it was the best on the market. That is so wrong. I purchased my Maytag Bravos washer and it has been a nightmare. Never again will I buy a Maytag. I have replaced two belts. It never spins the clothes out. Always have to restart it to respin. It turns off in the middle of the cycles. It will take hours and hours to do one load. At this time it just puts up the minutes and counts them down...does nothing. I am just fed up with this washer. I also bought a Maytag Centennial Commercial dryer. I have replaced a belt once. I would highly recommend not buying the Maytag Bravos washer. Save yourself the headache.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

In October 2016 I purchased a New Maytag washer (Model# MVWC565FWO) from LOWES. I bought an extended 5 year warranty with it as well. I have my invalid, totally incapacitated Sister living with me. The situation requires several loads of washing each day due to her conditions. TWO WEEKS after starting to use it we began having issues with the washer. It would stop in the cycle, lights flashing, only way to restart is to unplug it, move control from wash cycles setting to drain and spin... then within the next 3-4 loads it would do it again. Sometimes it sat for awhile I would smell like an electronics Odor getting hot... I called Lowes. They replaced it. Approximately 3 weeks later the NEW washer began doing the SAME THING...Lowes would not replace it with a different Model or brand... only send a repairman out. Long story short, he has been here 4 times, replaced the Computer Control with NO IMPROVEMENT!!! NOW Lowes is sending him out again and saying that if this doesnt fix the problem they will refund my money... My problem with it all is this... IF MAYTAG is having these type issues, WHY PRAY TELL, has a recall or solution been found and passed on to the repair folks??? I bought this Maytag due to #1 Reputation, #2 It was Assembled in the USA, NOT South Korea like the Samsung with recalls... Now all this is going on. I WANT A WASHING MACHINE THAT WORKS RIGHT!!! This is totally unacceptable and totally uncalled for. WHY could these Govt agencies and Manufacturers not LEAVE the washers alone? Computer technology... PLTTT. The old timers controls gave no problem in over 40 years of using them. Now this crap.

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

Bought a Maytag dishwasher (Model #MDBH979SAM0) three years ago. Four weeks ago the control panel wouldnt work correctly. No matter what cycle I attempted to select, other cycle buttons lit up. The start button did not light and the cancel button would not turn off. I called a repair guy, he came out and said Maytag was having a lot of problems with the control panels. He reset the machine and finally got it working again. He said he wasnt able to get a new control panel from Maytag due to demand/delay in manufacturing. Today the control panel went out again. Based on all the other reviews Im not sure its feasible to put more money in this machine. Ill research other dishwashers and get one that has a better performance record. DO NOT BUY A MAYTAG.

Maytag refrigerator model MFF2558VEM9 purchased in November 2012 from Home Depot for $1329 suddenly would not maintain freezer temperature under high 20s in April 2017 (4 years, 5 months). Repairman says it has coolant leak, probably due to corrosion within the sealed system. Cost to repair - $1500. Repairman says this is a common problem.

My Maytag refrigerator has driven us up the hill and back and has taken us several months in order for us to get the issue solved. This is quite an expensive fridge freezer and the after service has been diabolical to say the least. All their service calls in the UK were handled by a third party and it seems that there is some sort of change of ownership between Whirlpool and Hotpoint so after all the previous visits by different companies the problem of water leaking unto our floor is still going on and now all their call are being routed through a major insurance and a utility company who are more interested in trying to signing you up on one of their insurance policies than fixing it.To make matters worse the contractors they use are absolutely useless when it comes to fixing american style refrigerators. I was told I needed various parts which would have cost hundreds of pounds or that the appliance was uneconomical to repair. All of which was untrue. This I later found out when after emails after emails Whirlpool passed on the contact details of a service agent ags refrigeration who came out and found that there was a fault with the water in line connector at the bottom of the refrigerator which they replaced.

Bought a stove in May of 2014. In July of 2014 we noticed a 1x6 stain inside the glass of the oven door. I called Maytag and they stated only 30 day warranty on cosmetic flaws. I said this was not there when we bought it. They asked if anything had boiled over because if liquids get in the vents on the oven door it can get in between the glass. I stated no, only cleaned with Stainless steel clear. They stated most likely when I sprayed the door it ran down in between the glass. I said that is a flaw. They said, no the vents are there to allow heat out. I asked if they also were designed to let liquids inside the glass, they said no, I said design flaw. They will do nothing. I also pointed out that nowhere in the owners manual is there a reference to this possibly happening. Our sons in laws have a 3 year old LG stainless steel with vents and have never had this problem. Maytag will not stand behind their products even when they are the ones at fault. Buy a different brand.

If I want to line dry something, first I have to pick off all the lint. Even when I use the dryer, I still have to pick off lint and there’s often creases with dirt dried right in. I have to inspect everything that comes out of the washer to see if it is clean before I dry it. This doesn’t save water, as I often have to wash things at least twice. Awful! Also, ridiculous. A wash machine is supposed to get things clean.

DO NOT BUY MAYTAG REFRIGERATOR. I purchased a Maytag refrigerator 3 years ago, now it started to leak water on the floor. Repairman said this happens after about 3 years to all Maytag refrigerators because the water hose is too small and gets plugged which causes water to flow into bottom of freezer; 2 inches of ice on bottom of freezer. Now we have to remove everything from freezer and refrigerator, unplug for 2 days to melt ice so we lose all of our food in freezer and refrigerator.

I bought a Maytag MMV1153BAW Microwave. Within a year, the electronic key pad started cracking from normal use. After two years, the microwave intermittently starts then just stops, with the key pad showing 0000. We must unplug the device, or turn the breaker off and on. I called Maytag about the key pad and they said it wasnt covered, and a replacement key pad cost more than the microwave. After two and a half years, we purchased a new microwave, and have sworn never to buy Maytag again.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

Washer model mvwc200bw1 c43942055 -Worst washing machine ever! The clothes come out all twisted together, I cant even see how the washer works because the lid locks when washing! The sound the washer makes while washing sounds like its barely even washing the clothes! I will never purchase any Maytag products and I wish I could return this one!! So disappointed, Im sticking with Whirlpool!! Plus the clothes dont even get that clean!!

Bought a Maytag refrigerator from Home Depot about 2 years ago. Like everyone else we are having leaking problems from the freezer drawers. I wonder if anyone has had it repaired and whether it was repaired

My grandmother got a Maytag Bravos XL MVWB755 washer and from day 1 she had to call Maytag with issues due to residue left on the clothes. They told her to not use this setting... buy this detergent... only use cold water etc. Never did they offer a repair guy to come out. A year passes still having issues shes out of warranty. They now offer a repair guy but claim theyre going to charge her $90. Once she explains to them that she was never offered a repair guy & they shouldve done this before. They decided to waive this fee and send a repair guy. Once the technician comes out to the house they do absolutely nothing and they fill it up with water say we need to clean it and Ill come back out and do another diagnostic. When they come back all they do is fill it up with water get a glass check the water and say, Nope, no floating residue. Everythings fine. They then tell her she needs to get a water softener which is going to be hundreds of dollars.The technician also says do not use any other settings except for these two. Can someone please explain to me why they have all these dang buttons and settings if were not supposed to be using any of them and why all of the clothes come out with soap residue scummy residue all over them? The old washer never did this. It was a Kenmore and its the same water same everything but this Maytag washer is been nothing but problems. It leaves the residue which is stripped all over dark and white clothes, it is extremely loud, not all the clothes even get wet! Maytag is been extremely uncooperative with assisting my Nana. They tell her no one else not one other person is having this problem but when I look up this issue I find that about 2500 people on this forum are having very similar problems. Something has to be done. Maytag should have to take responsibility for this washer. The bottom line is it supposed to be an XL. When my grandparents are washing its only for two people. Theyre not even filling that washer up of all of the clothes are not even getting wet. It just goes to show you that the energy-efficiency that they claim is not working. The washers not getting enough water inside of it. Its not fully rinsing the clothes and no one should have to put the clothes in wash them then do a whole another rinse cycle just to get the dang soap off. So basically at this point she stuck having to do multiple washes using way more utilities than she should have to and Maytag is basically going to do nothing. It wont help her over the phone the technician is a joke and it looks like so many of you people are having the same issues.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.