Like everyone else Im calling corporate. Mr Fettig he should be in hall of shame after these complaints with their defective product. My fridge leaking, ice maker broken, water everywhere and eight inches of ice. I wonder if he owns a Maytag himself? Oh well after a while he might have a flood on his floor. This should be recalled just like my first model in 2001 that was a fire hazard. I had to go to the top then and I will now also. We should be protected from buying garbage while he makes 4 million a year.

I purchased a Maytag model 4000 Front Loading washer in April 2010 and in May 2011, the tub bearings went out which is a $600 repair. Now in January of 2012, the tub bearings are going out again. Neither Lowes nor Maytag are willing to do anything to remedy the situation. Do not buy Maytag and do not buy from Lowes. Their major appliance buyer has to know about this and continues to retail a product not fit for its intended purpose.

Maytag Bravos MVWB725BW - Purchased this washer last year and have been very unhappy with the way it washes. It is extremely harsh in the way the agitator moves the clothes. Because it has a low water level the clothes take quite a beating in the washing process. This is confirmed when I remove the clothes from the dryer and proceed to clean the lint filter. The filter is constantly full of lint, even after drying clothes that have been washed numerous times before. Additionally, the clothes, even though being put in evenly, end up bunching together.

I purchased a Maytag refrigerator (MBF2258XEB), stove (MER8674AB) and dishwasher (MDB7749SBB) on May 26, 2013. So far all three have been worked on. First, the dishwasher would not fill up with water after the trial run. Called the repairman out. A tag was placed in a position that was preventing the dishwasher from loading up with water. Granted, we should have taken the tag off, however, it stated not to. Lucky for me, I am still under warranty. Second, the refrigerator, which is a freezer at the bottom, started to leak. I thought that maybe we were dropping ice. However, I finally called and had the repairman back out. He knew exactly what the problem was because Maytag knew about it. There was a faulty plug. So in a matter of mins the problem was fixed. Lucky me still under warranty. Those two things happen within six months of purchasing these items. Now, the oven does not work. It heats up to the desire temperature but then cuts off. Called the repairman and he thought it might be the lower baking element. Unlucky for me, warranty has expired. So, $90.00 for service call. Received a called from the repairman, $120.00 for labor and $70.00 for the baking element. I purchased the baking element myself, $58.08 and installed it. Still does the same thing. Now I have another appointment for him to come back out and see what is wrong. Another $90.00! So far I have spent $238.08 on a $699.99 stove. I will never buy Maytag again. Depending on the amount to repair will depend on whether or not I go back to Sears and buy Kenmore. I had Kenmore for 10 years with no problems. I should have gone back to Sears for my upgrade. I did contact Maytag via email. I am still waiting for a reply. Live and learn!

About 6 years ago we purchased a new french door style refrigerator. It lasted one year and one month then needed over $700 in repairs. First you need to know I am into electronics, DeVry graduate with 30+ years experience in repairing electronic devices. The Maytag basically frosted over in the freezer and was warm in the upper part of the fridge. I called a friend who had experience fixing fridges and lo and behold we found something really unusual.The way this machine operates is by blowing the cold air from the freezer up into the fridge. There is a fan located in the back of the freezer wall that does this. We found the fan, which was mounted in a grey box, spinning at about 2 revolutions a minute. My friend took me to the wholesale parts distributor he uses and we gave them the brand (Maytag) model (MFD2561HES) and they gave us a fan... just a fan with two wires. No grey box with fan inside... At this point I got curious, I mean WTF?!?The grey box was made not to be opened and I had to get clever so as to not damage whatever was inside it. After getting it open I discovered the fan inside was wired to a circuit board which upon inspection was a timing circuit. This is why the fan still turned only too slow to function. The new fan was installed and my only problem with the fridge now is the ice maker, which I disconnected.Conclusion: Maytag actually designed this fridge to break down and require hundreds of dollars of repairs AFTER the warranty expired by installing a timing circuit that disables the fan that drives the cool air to the upper part of the fridge to keep your food cold and your freezer frost free. Replace the grey box with a normal fan and youll get years of good use out of your French Door Maytag! As long as you clean the seals regularly and dont mind buying ice to fill the tray with... The repair cost me $39 and a six pack of beer for my friend.

Duck bill valve for defrost water from freezer malfunctions, water flows into freezer freezes, then eventually overflows onto floor. Huge problem for folks with wood floors. Also a slip/fall danger especially for the elderly. When the repair line is contacted, they deny the problem and say you are the only one. But if you do your research, you find there are hundreds of complaints and in November 2013 they issue a service bulletin, but its internal, not meant for consumers to find out. So if you have this problem, go to the Consumer Product Safety Commission and fill out a complaint. Maybe then something may come of it.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

My microwave will not work when the door is shut. It says: Door open. It’s worked intermittently, doing this for about two weeks. Then my husband woke up one morning a week ago and the microwave was on like it was running, light on but the plate was not turning. So we’ve had to unplug it and do without during thanksgiving weekend. This seems to be a common issue, obviously from the reviews below, so shame on you Maytag for not owning up and doing the right thing, covering repairs or sending out a recall. It’s a $112 service call here locally plus parts and labor. I will certainly be telling others not to go with Maytag. Maytag is lucky- it turning on by itself AT NIGHT, WHILE WE WERE SLEEPING, that it did not cause a fire or something. I’m pretty upset that it’s inside a 2.5 year window and already has issues.

First off I dont usually spend my time writing complaints; however, I feel Maytag is deserving of my complaint. Purchased dishwasher Model #mdbh979sab1 in 2013 and days before the 1-year warranty was up the front control panel quit responding, rendering the appliance useless. Got that fixed under warranty. Now about 1 year later guess what... Its got the same problem. Began to read others post on this site and found that this is a common issue. One person posted that her dishwasher began to smoke and nearly caught her home on fire. Maytag was kind enough to offer a paid service call and enrollment into their extended warranty program. I think Ill cut the umbilical cord on this one and go get something more reliable and doesnt pose a potential fire hazard.

We inherited this Maytag (Model MGR7662WW) when we bought our house this year. I love this unit. It cooks accurately, its easy to clean and its just rock solid in its performance. I never worry that the cook times are going to be off either. The oven racks are solid and the overall look is nice. Our friends and family love the center grill as much as we do. If I need to pull something off the burner I dont worry that Ill scratch the stove top with this feature. The oven heat is also pretty contained. Our old oven radiated lots of heat through the top. This one doesnt and thats a huge plus. The only reason Im not giving it 5 stars is that the grills are cracking (not the center one). However, I have no way of knowing if the original buyer damaged them or if its a defect in materials. They still work fine but I will need to replace them at some point. Given the cost of replacing them Ill wait as long as I can.

Purchased a Maytag side by side MSB27C2XAM00 in June 2014 to replace a 20 year old Kenmore. After 14 months the fridge stopped keeping things cold in the food compartment and in the freezer. And, the water and ice dispensers stopped working. Called Maytag and they confirmed the fridge was 2 months past the warranty and the best they could do was offer an extended one-year warranty for $325 and set up an appointment. I declined and called a local repair company. They responded promptly and discovered the problem was a bad board. Had to replace the board at a cost of $475 (parts and labor). It was $150 more than the extended warranty but I was already in the hole for $100 service call and I was able to get the fridge repaired on the spot. I had the Kenmore for 20+ years without one repair. Maytag was good for one year and 2 months. Dont know how this company will last with a $2000 product that lasts a year. I can not recommend this product and advise anyone in the market for any appliance to avoid Maytag products.Updated on 11/20/2015: After the board was replaced, the fridge worked but was not keeping either of the side by side compartments cold. They were cool but not cold. Repairman returned. Said it was the compressor which needed to be repaired/replaced. Maytag said the compressor was under a 10 year warranty unlike the other parts of the fridge. Good news, Maytag covered the cost of the part / but bad news that it broke after 14 months of use. However, the service people told me the cost of the compressor was the smallest part of the repair. Labor and service would be costly and Id be better off getting a new fridge with a 5 year warranty contact. After I got over the initial shock of having to toss a 14 month old fridge that cost $1500 and complaining to Maytag, I went to Lowes and found a replacement fridge. This time it was not a Maytag. Moral of the story stay away from Maytag. Dont be fooled by the brand. Avoid them at all costs. And purchase a fridge with a 5yr+ warranty contact!

I bought a new smart washer and dryer from Maytag in mid-2019. Beginning in the first few weeks the machine did not perform as expected--cut off in middle of cycle, door failed to unlock at end of a cycle, constant error messages that made no sense (power failure when power didnt fail, codes that arent defined in the owners manual). To make a long story short, the company that does their warranty repair, which has worked on the machine approximately 8 times, tells me there is nothing else they can do, the machine is a lemon. But their customer service department refuses to replace it. They say it must be repaired, yet again. But the parts are out of stock (which should be a pretty good indication that theres a problem with product quality). So I am to wait. How long? They dont know. Call again tomorrow.Do NOT buy a Maytag appliance. Customer service does not stand behind their products and the products are no longer up to the quality I had previously expected from Maytag. Additionally, telephone wait times on the customer experience line can exceed an hour and are customarily over 30 minutes. Never had an experience like this with any other major appliance customer service department.

We bought a Maytag dishwasher March 2012 and the unit wouldnt turn on October 2013 - 6 months after the warranty ended. We called their service department and they told us to unplug the dishwasher or turn off the circuit breaker. We did so and the unit still would not turn on. We called a repairman who advised us that the touch pad was not working. The cost with parts and labor would be close to $300 which was more than half the original price. We repaired it and I sent all the papers with a letter to the consumer department and today I got a call advising us that they would not do anything. Do you think I have any further recourse? If not, I will never buy a Maytag product again and will advise anyone within a listening area as to how we were treated.

So far we have replaced the belt. Clothes have never come out clean. High Efficiency... Yeah, we have to put it on extra rinse to rinse all the soap out or wash twice because the clothes just do not get clean. Now it stops right before it drains after the wash. So I had to pull out clothes and use pitchers to get water out before we could tip forward and pull hoses to drain the rest. We checked hoses and connections. All lights work, it did a wash cycle, and again stopped before the drain. Really. All I got was “Didnt you take out the extended warranty?” Well, No I did not. Why would I consider the fact that MAYTAG would need repairs within the first 3 years. Its not like I do a lot of wash. Or have big bulky items. I have a laundry mat close by for that stuff, because it wouldnt get it clean anyway. Never again…

My daughter purchased this washer and matching dryer as a set from Lowes about 4 years ago. It was one of the few with an agitator and that is what she wanted. After using the washer for the first time she was very disappointed to find that the shortest cycle took over an hour and that the locking lid feature couldnt be bypassed. A few weeks ago the washer began gushing water onto the floor which flooded the basement below. She had purchased an extended warranty which was due to expire the following week.She called Lowes and scheduled a repairman. He finally came 2 weeks later and used the Internet to help him diagnose the problem!!! We could have done that. He decided that the control panel was only allowing the agitator to turn in one direction during the wash cycle. So essentially it was spinning a tub full of clothes and water causing lots of water to overflow the tub onto the floor. Needless-to-say he had to order a part and cant return for over 2 weeks to install it. IF this is even the problem! He also said he couldnt disable the locking lid feature! If my daughter had been able to open the lid when the problem started she would have known more about it.We are thankful her machine was under warranty but she will have been without a machine for almost 2 months when and if it is fixed. This is completely unsatisfactory for a gently used 4 year old washer. The dryer takes forever to dry also. If you are buying Maytag based on how long your grandmothers machine lasted, you will be disappointed! This washer caused so much damage we had to file a homeowners insurance claim!

We purchased all new appliances 3 years ago including a Maytag dishwasher. Same problem as a lot of others. We had the control board fail three times in just four months. Now today the repairman came and while he was here contacted other Sears technicians and Whirlpool technicians. They came up with the idea to replace the detergent dispenser which they said is causing the main control board to fail. However, while the tech was on the line with Sears and Whirlpool they done troubleshooting on the detergent dispenser and found that it was all within specifications. In fact, that was not a problem because it worked as it should. But in their wisdom they decided to replace the detergent dispenser. We now have to wait another ten days for the part to arrive and reschedule another appointment to have the detergent dispenser that works replaced. The serviceman that was at our house said that they are making him replace a part that is working and that this does not need to be done but he has to take instructions from Sears technicians. Our service person said that he doesnt anticipate that replacing the detergent dispenser will make the dishwasher work but he said if it does it will only last a few weeks as before and then fail once again. We have the dishwasher on extended warranty and there are about 22 months. I suspect that this one will be going to court to get resolved. Never Maytag again or Whirlpool.

Since the day I bought the Maytag Bravos XL washer it never worked correctly. An entire year of several repair men, which half said there was something wrong and other half said nothing was wrong with it. Now it sits in my garage as the most expensive paperweight. After repeated requests, the Whirlpool company that owns Maytag now refuses to stand by their product, replace it, refund it or anything at all. They have washed their hands, yet I cannot wash my clothes in it!

Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

I have Maytag dishwasher model # MDB7609AWB2. I purchased it from Sears on 5.30.10. It was installed 3 weeks later. From June 2010 through November 2011, the dishwasher has stopped working 3 times, every 6 months, requiring a service call to fix the electrical /circuit board problems. The aggravation of owning a poorly built machine and inconvenience of waiting for Sears to send a repair person has sealed our decision to stop doing business with Sears and Maytag.

I bought my washer just over 3 years ago and it started making loud clicking noises and it seems like the agitator function is not working at all. I have a repairman coming over in a few days. I knew I should have gotten the extended warranty!

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

Waste of $1700. Well all I can say is I wish I woulda read these reviews prior to buying but thought Maytag was a good brand. Boy was I wrong. Never again will I purchase Maytag products. I must say I haven’t had any issues with the dryer. Works great. The washer on the other hand is garbage!! It barely cleans the clothes. Some articles only get partially wet. Everything tangles together. The worst part is all my dark clothes ends up full of dust and lint. They look dirtier coming out than when they went in. Very disappointed. If you use deep load it takes about 1 1/2hrs to wash, definitely not energy efficient, and clothes still have lint on both cycles, and unfortunately most of our clothes need to be hung up, so dryer can’t pick up the lint. My old wash was way better. I shoulda went for same old style. Save you money and buy another brand.

We bought a Maytag Bravo model top washer recently and have no good things to say about it. The startup time is too long and clothes are coming out with lint all over them now. If the unit could be returned we would do it immediately but we cannot.

I have been Maytag customers for 40+ years. I purchased a new Maytag washer and dryer at Home Depot last year. The paint is coming off and the top is starting to rust. We have had Maytag washers and dryers for as much as 17 years that did not rust. The reason we bought Maytag was quality. Rusting in one year is not quality. Please contact us ASAP. Home Depot said there was nothing they could do.

I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.

Bought these in March of 2016. Got a 3 year warranty. In Feb 2019 the dryer burnt out the switch. Just by a hair it was covered. Now started working only on one cycle. The Washer with a 10 year limited warranty just stopped working out of the blue. ONLY 4 years old. Seriously???? during the Coronavirus outbreak!!!! I am beyond upset with this manufacturer. Geez my Kenmore washer and dryers lasted 17 years!!! My Whirlpools lasted 21 years!!!! What kind of junk are you putting on the market???? I was told at Lowes these were state of the Art machines - the best!!!! Here I am so stressed wondering what the Hell Im to do! Never buying Maytag again.

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

I purchased a new Maytag range (gas) in June of 2012 - 6 months ago. I have had the same problem many others have had (as Ive just read) with the toxic smell every time I used the oven. I was told it was just the chemical burning off from being new. I have never owned a new oven so I took their word for it. On Christmas day, my kids and I were going to bake cookies and set the oven to preheat. Flames and black smoke were shooting out of the range, and the fire department was called. Even after the fire department put out the fire and removed the stove from my kitchen to my front porch, they spent more time investigating the situation to make sure my home was safe than the certified Maytag repair person that was dispatched out by Maytag to service the range. This stove is only 6 months old and still under warranty with Maytag. The service person they sent out did not take the stove apart and spent less than 5 minutes looking it over; then he determined that it was a grease fire caused by owner’s negligence. I disagreed with him and told him I have been cooking for many years and thought he did not do a thorough job to determine the problem with the range. He got very upset with me, took his bag and left without leaving me a service slip. I asked Maytag to send someone else out and explained to them that this service person did not do a sufficient job in examining the range, nor did he perform any kind of service to get the range back in working condition. Maytag claims they will not send anyone else out, and there is nothing more they will do for me. They say it is my fault it caught fire; and if I want it fixed, I have to pay for it myself even though it is still under warranty with them. My stove is still on my porch where it has been since Christmas day. I then visited Maytags Facebook page and corresponded with others whom have had similar issues with their products and the lack of customer service from this company. Maytag has now blocked me from commenting on their Facebook page. The customer service rep on that site asked me to email her all my information about the range and my issues with it, and she assured me she would respond to the matter. As of yet, I have heard nothing back. I am terribly dismayed by the way I have been treated by this company, their so-called certified service technician, and that they do not honor their warranties or stand by their products. I am cooking for a family of 5 in a 12-year-old microwave (which is not a Maytag by the way) after spending over $600.00 on a brand new range.

So this washer, Bravos MCT cleans good not great. Saves water but clothes dont always come out clean or smell fresh. We have had it for just over a year and the control panel stopped working. Warranty is good for only 1 yr. UGHH!! It is all one unit so the complete circuit board had to be replaced. Half the cost of this washer new! I saved money by replacing it myself. Took 15 minutes. Very easy. Disappointing when you see this is a come problem with this model.

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

I bought a Maytag Bravo without an agitator. Regretted from the 1st load. Some of my clothes do not even get wet and I bought the commercial grade. My 20 year washer that was on its last leg washes better than my brand new Maytag. Please do not waste your money, your clothes will not come out clean.

Great appearance, great job on getting our clothes clean and dry. Good dryer cycle choices and output. Good washer cycle choices and output 98% of the time, BUT, sometimes the washer needs a do over about once in 50 loads. Overall, two thumbs UP.

Would give them 0 Stars if that was an option. Bought a Maytag washer and dryer in Aug 2021. Washer broke Jan 6 2022. Called Maytag/Whirlpool on Jan 6 as it was still under warranty. They only had one service company in our area to work on the washer. I called them and it took them 10 days to come see what is wrong. Ordered parts. Said it would be 2 weeks. We are now 6 weeks into this with no parts. Called customer service and they said they were notified that their service company needed a part and would take another 21 days to resolve. Talked to a supervisor (Demetrius) who sounded like he did NOT want to be in that position. Offered no solution other than we will just have to wait. Threw a 3 month extension for the warranty on which still does not fix the problem. Sad to see this company go down the tubes as it was once a pretty decent business with solid products. No longer.

Purchased a Maytag top load HE washer in November of 2011 & by Feb. of 2012, Maytag had to bring me a new one after a service call to fix lasted only one week. So at the end of Feb. 2012 they brought me a new Maytag Centennial HE Model# MVWC400XW3 & this one lasted till January of 2014, less than 2 years old & quit working. Had a service man come out to look at it & was told not only it would need a $400 repair but it was made by Samsung, but Maytag had their nameplate on it!! Called Maytag customer service line which took about 30 minutes of hold time to get through & was told, SORRY, LADY, we cant help you. Youre just out of $613 after less than 2 years of service & we WONT help you!! This company should be shut down, they are liars, frauds, cheaters, producers of poor quality products, uncaring, & sellers of the worst products on the US market & I hope the Consumer Affairs will see enough of these complaints about Maytag products & shut them down!!!

Shame on Maytag! Customer Service is appalling! Paid 2500 for one of their top of the line refrigerator/freezer and had the repair people 5 times in one year. It was determined that it is a bad model number that Maytag wont recall but knows it is faulty. Started with ice build up in freezer making it sound like a plane taking off. It kept running trying to defrost (energy efficient-right). The repairman put in a request to have the product replaced based on symptoms and freezer being at 26 degrees. We had to wait five business days for Maytag to review it. I have a family and was having guests. They told me to buy a dorm refrigerator and they would send me a small credit towards it in 4 to 6 weeks. They finally agreed to replace the known faulty model, but I have to wait for the exchange team to contact me (2 weeks later). I keep calling and leaving messages but cant get the exchange team to even return my calls. I have my sons graduation this weekend and I dont have a freezer and my refrigerator is faulty with all my vegetables rotting within two days. It also took two days to originally get someone in management to call me back (even though it did no good - she cant help me). You cannot talk to management if you call customer service. They downright refuse! What a company!

Maytag Neptune Washer Drum Bearings have once again failed. Last time, I replace the whole drum via diy, cost was about $160 for the part. Now I see that outer drum is $500 +/-. I just may only replace the Seals & Bearings this time OR just part this thing out and buy a real machine without the Maytag name.

Washer stopped working, never did clean clothes. Out of warranty - some it is fix or buy a new one. DONT BUY!!

Purchased a Maytag French door freezer underneath refrigerator 8 years ago. It stopped working because of the circuit board located behind the ice and water compartment on April 7th. Contacted a Maytag repairman, which is a whole other story. Had to order the part, weeks and weeks go by telling us the part is coming. Then a call came from the repair man on June 17th, Maytag no longer makes the part. Meantime we located the part by taking the fridge apart ourselves and ordered it arriving today June 19th. Contacted Maytag - Whirlpool corporate. Answer, We are sorry we no longer make the part, and basically told me after spending $2800.00 8 years ago Im up the creek without a paddle.

Preheat the oven, put in the food. Oven does not maintain the temperature. Gives me a code of F2-3. Want to know what part needs replaced to solve this problem. If anyone can relate to this problem or help me with information please respond to this or email me.

Purchased Maytag washer Centennial Econoserve washer. It was 2 years old Aug 2013. Washer stopped working Sept 16, 2013. Of course since it had Maytag name brand, I did not purchase extended warranty due to thinking it would at least last more than several years. I called Maytag/Whirlpool. They gave me name of authorized repair in our area. So far they have come out 2 times. $560.00 later, it is still not working and they have no answer as to how or what to do. We are now into $1300.00 between purchase and repairs and still no washer. We are retired hard working people and this is really a bad way to treat consumers. Maytag customer service could care less about the situation. They just say we should have purchased extended warranty.

I write this as the repairman is fixing my Neptune washer. As with many other complaints, I was experiencing the awful mold smell with the only fix being leaving the washer door open when not in use. This works but for the past few years a switch on the front broke which means we have had to leave the top off the washer and rig it every time we used it. Sometimes it would work and sometimes an error code would show and I would have to just turn to spin and finish that way. At the same time in 2005, I purchased all Maytag appliances. First the microwave went out then the ice maker broke and is still broken, then the dishwasher went out and had to be replaced. Washer broke so basically the only thing that has had no issues is the oven and all happened just outside the five-year warranty. Never again will I buy Maytag.

We have had this refrigerator, model MFI2665XEM7, less than two years. The ice maker stopped working and we had it replaced at least 6 times in a two month period. We had a solid ice sheet in the bottom of the freezer drawer and it leaks water on the floor constantly! Even today... after another ice maker replacement, we have no ice! I never wanted a Maytag, but finances and the small space we had gave us little choice. I am not sure what our next move is. I will NEVER buy a Maytag product again! I should have google this sooner and we could have saved the poor repairman all of those trips!

I purchased a Maytag Bravos line washer model # mvwx500xwo back in Oct. of 2010 thinking that it would be great to save money on the water bill. I first had issues with it putting holes in my clothes. I then found out if you do not zip up all zippers and button all buttons, the machine will rip them up due to the high speed spin cycles. Now, the washer will not fill with water or start the wash cycle. I mean really, its less than two years old and I have to shell two hundred plus dollars to fix a washer that only cost $500. I guess I know what brand not to shop for next.

Bought a Maytag dishwasher 2011! Use it 2 weeks, digital board went down had it replaced! Now 2013, the board is down as well as the motor!! Can you imagine I use it once a day, at most 2 people in this house, and it completely breaks down! Thank goodness I have a Home Depot warranty. I would strongly advise against this product that I spent over $500 for 2 years ago!! How they could sell this dishwasher is a mystery.

I have owned a Maytag gas dryer for 10 years now. I have had to replace the idler and belt 4 times now. This dryer appears to be built as cheaply as humanly possible just to get it past its almost non existent warranty. The replacement parts are even worse. The idler has a bronze bearing in it as a wear item. Really??? Why was this never even considered as a part that could be lubricated at least occasionally?Granted, lots of people do not have any mechanical ability at all and just pay through the nose for a repairman to come to their place for any repair then pay dearly for the service but, I DO have mechanical ability so I do all the work myself. That is why I know firsthand about the terrible manufacturing results and the very cheaply built replacement parts available at outrageous prices.

Mine is a Maytag wall oven and I purchased it because I had a Maytag Range in the house before this and loved it. It is a very accurate oven. I would rate its accuracy with the Thermador wall oven which is one of the most expensive ovens. It heats quickly and stays within the range of temperature you are using. Everything comes out just right. I like going to a Maytag dealer who knows a particular brand or brands not a large dealer of many brands. Always do some homework since brands can change over time with who owns them and who is manufacturing them.

We have a Maytag Gemini Double Oven Range Model MGR6775ADW. This is a gas range and it was purchased in 2006. This past Saturday afternoon after cleaning the dishes, the igniters on the range starting ticking on their own. I checked to make sure the knobs were not on and they werent. The ticking finally stopped after about 2 minutes. After the ticking stopped, we planned on going out for a walk. Fortunately we didnt. In about 10 minutes after the igniters quit ticking, the range burst into flames. Flames were in the top oven and shooting out the vent holes and the holes where the knobs are located. Coal black smoke was also pouring out of the vents. I quickly pulled the stove away from the wall to prevent the cabinets from starting on fire and I pulled the plug to shut off electricity from the stove. The flames subsided shortly after pulling the plug. The kitchen and house smelled of burning wire insulation and plastic. After doing some research on the internet, I found out that many other people have had the same problem. I reported this to Maytag Customer Service and they wanted to send a repair technician to fix it. I told them I didnt want it fixed but wanted it out of my house. I told them I didnt trust the range since some people reported they had it fixed and the fire occurred again. I wouldnt be able to sleep or go out anywhere knowing that the kitchen range could erupt into flames at any time. The factory authorized repair technician, from A&E, did come to inspect the damage and to report back to Maytag on his findings. He admitted that he wouldnt even trust the range in his house. After paying $1300 for this range and only getting 6 yrs. of use, I feel that we deserve some restitution from Maytag on this badly designed and dangerous piece of equipment they have been selling. Do not buy the Maytag Gemini range. This is a bad and dangerous product.

Purchased a Maytag bravo washer model #MVWX500XLO 2yrs and 6 months ago April 28/2011. In Dec. 2013, I heard a loud clanking sound and was shocked. I thought that some coins were lodged somewhere.... not the case. I put up with the clanking until after Xmas.... Finally I called a licensed technician (in business more than 20 yrs). He immediately identified the problem.... THE TRANSMISSION was shot. Wow what a shock! 65.00 dollars house call to give me the news. I phoned head office to no avail. The office said that it is not covered and that the part would be in the neighborhood of 350.00 $ and probably the installation around $160.00. I am still in shock. We paid around $750.00 for the unit. The technician said that it is one of the worst machines he has ever worked on. I am now talking with Home Depot to see if they can get some compensation on the unit (speaking with the rep). Will I buy another Maytag (by the way) made by Whirlpool... I guess not.

I made the mistake of buying a Maytag 2 years ago, this machine would not wash clothes even when using the deep water wash. I should have looked at it closer, it is so full of modern computer garbage that I was having to wash clothes twice so the water saving was negative. I own a business across from a major shopping center so what we did was we loaded it up in one of our trucks and parked it in front of our business with a giant sign and invited people to take a look before buying one. In 6 months we must have had at least a 1000 people inquire.

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

Recently purchased Maytag Washer and Dryer from our local Home Depot June 2020. The appliances were finally delivered in August. When both appliances were installed, the installers made sure the washer was working properly and there were no leaks. They did the same for the dryer to make sure it was working properly. When the dryer was turned on however, the motor blew up and there was smoke coming from the dryer! I am now sorry I purchased Maytag. I had narrowed my choice between purchasing Samsung or Maytag. Im now thinking I should have gone with Samsung. Im supposed to receive another dryer today. The washer works, however its very, very loud. For the amount of money I paid, I hope these last for a while.

I purchased the microwave less than two years ago. I noticed the display panel would not always work a few months ago. This is part of the control panel that shows time, etc. Called Maytag just now & they told me that the control panel is starting to fail. I could purchase a one year extended warranty for $289!!!Are you kidding me??? The part alone would be around $160. What has happened to Maytag? I thought they had a good name. :( Very disappointed.

In October 2017, I purchased a Maytag MVWB765FW0, thinking that it would live up to the Maytag reputation but I will NEVER buy Maytag again. This machine is more suitable to wash industrial canvas rather than clothing and bedding. All the laundry is twisted and mangled and ends up in a large tangled ball at the bottom of the tub. My clothing is being destroyed faster than I can replace it.

My Maytag 2000 has ripped our clothes. This is my 1st front loading set. I looked on the internet and it seems that this is a known problem. Very upset that a brand that I had for 30 years and recommended to others as well has turned into a terrible company. Im a single mom and Im not in a position to replace a washer every year. I trusted Maytag! A recall and either replacement of the parts, or delivery of new part to fix the problem should have been put in place. I wrote to Maytag to see if they will do something to fix this problem.I have the set, washer shakes a lot, but works well. Washer also always has a lot of water left on the door seals folds, terrible design... I will post on other sites to warn other customers. This is not OK, my clothes are destroyed. See pictures. Clothes got trapped in a gap that exists in the perimeter of the opening, where it meets the door. Why is there a gap at all???

We bought a Maytag washer and dryer in April 2012. A few weeks ago the washer while it was spinning out, it sounded like it was metal on metal. Sears came out and said the transmission and the tub had to be replaced and the tub was created to the transmission. My husband and the only ones living in home and I sort my clothes, so I dont have big loads. I contacted Maytag, their answer was its out of warranty so we are not going to do anything for you. Anyone who buys a Maytag Washer, watch out what youre getting.

It is impossible to dry clothes in the dryer without the worst wrinkles you can imagine. I have 2 of them and they are both horrible machines!! The drum spins too fast which causes the clothes to get stuck against the tumbler fins. The centrifugal force holds them there and they just ride around without tumbling in the drum. When the cycle is finished the clothes have been dryer while jammed up against the fins and they are so wrinkled you have to wash them again. The ONLY way to get them through a drying cycle without a tremendous amount of wrinkles is to stop the machine every 5-8 minutes and fluff the clothes around inside the drum by hand. DO NOT BUY!!

My 2.5 year old hood range microwave stopped heating. I called repair guy, he charged $115.00 for barely a half hour and said he tightened a part and it should be fine OR the part would need to be replaced. Guess what!... That night microwave is still not heating anything. Dinos Appliance Repair is responsible to repair but Maytag doesnt stand behind its product. How do I get my money back when a repair doesnt repair anything? I wont buy Maytag again or GE.

Bought a Maytag washer from Lowes 3 years ago and it is just junk. I am 62 years old and never had a washer that actually broke down. What happened to good American technologies. I guess those days are gone, anyway dont buy a Maytag, duh. It is the day after x-mas and I have to buy another machine.

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

We purchased a Maytag Bravos X washer 2 years ago. Theres not enough water in there, and the clothes get so tangled that Ive had holes in them. Ive had technicians come out several times and they just say that its the water saving feature of the washer. I put it on the wrinkle control setting and the clothes come out ridiculously wrinkled. All of these problems are due to the water saving feature. I absolutely hate this washer and would never recommend it. I want my old washer back with the agitator and enough water in there to actually wash clothes.

I purchased a Maytag Bravo washer 2 years ago and it is the worst washer I have ever used. My clothes are never clean. It is always out of balance and is so slow and takes forever to do a load of laundry. It has started stopping on spin and have to unplug it to get it started back then it sounds like a jet coming in for a landing and has to restart the spin about 3 or 4 times before it ever finishes. I have had the repairman to look at it and says there is not anything wrong with it, but something has to be wrong for it to stop on spin and have to unplug it for 5 mins. in order for it to reset itself and start again.

This was purchased 3/25/2010 with the Home Depot Service Contract thru 3/2015 . We have already had a service call in 2013. We were OK until January 2015. Now we join many other customers with the leaking defroster. We have taken all the steps of the other customers. We went and called for a service appointment. Weve spoken to Maytag Customer Service 800-253-1301. Ive asked if there was recall? NO! I asked if there was log made of my call, NO! Any work done had to with Maytag Authorized Repair Person. The Home Depot Contract use a Non-Authorized Service Person. Weve gone to Home Depot. We are in a catch 22! We have spent good money on this refrigerator. Out of sight, out of mind. We will go back to Home Depot Again!

My refrigerator stopped working less than two weeks after purchase. The ice maker failed to produce ice. I feel they sold me a lemon. Yes, I do!

I bought this washer from Lowes in 2013. It worked okay for a little while but lately it stops mid-cycle. Clothes are soaked and all of the soap hasnt been rinsed out. Poor excuse for a washing machine! Will never buy a Maytag again!

If I can rate the AquaLift Technology oven cleaning system that my Maytag oven has as a “Zero”, I would. This technology only removes some of the spills on the bottom of the oven. It does not clean the sides or top of the oven. I’m back to the olden days of using a lot of elbow grease to remove splatters and spills. They say you cannot use any cleaners in the oven either. At least with the old ovens you can spray an oven cleaner and wipe it clean. This product has taken us back before there were spray oven cleaners!

I purchased a white Maytag gas stove over 12 years ago. It has been great and never caused any problems. I live alone and rarely use the oven. However, I use the stovetop daily for cooking. With continual use, it has a lot of nicks and scratches. It also has stains inside the glass oven panel that I cant clean. The glass would have to be removed in order to clean inside. This is why I give a rating of 4 stars. If I used the oven more frequently, I would notice if it had any problems with the temperature, proper cooking, etc. and could give a more accurate rating. I have small toaster oven and therefore, I cook practically all of my meals in the toaster oven.

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

I bought my Bravos XL 3 years ago after having older model Maytags since the 1980s. My mother also runs a laundromat and SWEARS by Maytag. To say Im disappointed in this purchase is an understatement!!! They have never washed the same as the older models. They twist the clothes horribly! Now Im having issues with all of my dark clothes getting grease spots on them with no apparent cause. I use HE detergent and softener (recommended amounts only) and clean the washer religiously, including the detergent, bleach and softener cups. I DETEST these machines. Also, the dryer never dries unless I run it for 2 cycles, regardless of what setting it is on. Waste of money and definitely not energy efficient when it comes to my water and electric bill, nor time efficient for me since clothes either come out still dirty or with new stains. After this purchase, I would NEVER buy Maytag again!!!!!!

I purchased both a Maytag washer and dryer and I am very disappointed in both products. Both appliances have electronic controls and are substandard. For the dryer if you do not touch the start area exactly right it will not start, can take multiple tries. For the washer, my town turned off my water to switch out the meter, once done the washer did not know how to clear the air in the lines and gave a LF error and no one at Maytag customer service could help me solve the issue and then could not set up a service call as their computers were down and did not have a process to call back the customer. This is terrible Customer Service - never again Maytag or any of their other products????

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I bought this MMV4205BAB microwave thinking Maytag was a good brand and I wanted an over the range type. Problems began when it would stop in the middle of a cooking cycle. I called the repairman as it was under warranty. It was decided by the repairman that the weight of thing was too great for its thin frame, not letting the door close correctly. I got a new one and it, from day one, would make a shorting sound every time anything was cooked, on the stove top, under it, while it was on. It finally just shorted out. I have a Maytag washer and dryer that are also junk. So, needless to say, Maytag, 3 strikes and youre out. I will never have another Maytag product and I let others know what a great product it is.

I grew up trusting and believing in the name brand Maytag. Unfortunately, I wont anymore. I purchased a Maytag MDB7749AWM1 dishwasher from Lowes thinking that I would not need the extended warranty because well it was a Maytag and they just keep working and working for years to come. Not true anymore. 1.5 years after the purchase the control board has gone out. I come to find that hundreds upon hundreds of people have all experienced the same thing. Shortly after the manufacturer warranty expires, the panel dies. By all accounts it is an issue of POOR engineering and Maytag now being produced by Whirlpool. The replacement part is between $150 and $200. Thats about half the purchase price. It is a racket. Companies like this probably think, well if we build something that is going to last and last we cant make money on that. So lets rig it so our stuff breaks right after the warranty and charge half the price of the unit to fix it so we continue to make money either by people buying the part or just going and getting a new dishwasher. Well I can tell you I will be getting a new dishwasher and it certainly wont be a Maytag OR a Whirlpool.

Purchased Maytag dishwasher from Ft Knox Exchange in 2011, Model MDB6709AWW1; Serial # F04117463. Like most posts before me, the panel started failing after 2 years. Unit is now inoperative. I am attempting to fix myself using repair techniques Ive found online as I refuse to pay hundreds of dollars to repair this piece of junk. Will never buy Maytag again.

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

We purchased a new Maytag dishwasher last year when we purchased our new home. All the other appliances were Whirlpool. This dishwasher runs forever. We have huge electric bills and I am sure this is a contributing factor. We purchased it from Lowes. They have sent out two technicians who say there is nothing wrong with it. One said it was because it was in an island. The other that our water is not hot enough. He turned the water heat up and now you have to warn people using it to be careful or they will get burned. No wonder the Maytag repairman is so bored. He knows the appliances he services are junk and doesnt bother. Take my advice. Buy ANYTHING BUT Maytag!

Our circuit board has went out twice. The stove is not designed well. The oven vent sends hot air over the plastic panel / circuit board. It melts... The first one was under warranty and the second, only three years later, was not. This is a very expensive part and Maytag will not even talk about giving me a discount.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

I purchased a washer in July and its already off track. When I seen it I know it was junk but the sales person assured me it was a good product. 3 months later its off track. No spinning. DO NOT WASTE YOUR MONEY.

I have been reading the recent comments about the Maytag Bravo I purchased in 2011, and is sitting in my laundry room broken down. The timer wont advance past 18 minutes. I have reset it to factory default a number of times to no avail. I am very frustrated that the customer service offered an extended warranty for $319 to cover the service repair and another 1 years warranty. My washer is three years old! The warranty they offer is half the cost of the purchase price! The quality of this machine is very poor. I am truly disappointed with Maytag, who used to be a company you could trust. They have lost my trust along with my business.

I have used several brands of refrigerators and Maytag stood out for me. Everything works as good as new. However, my experience with ice machines, has been the first thing to quit.

This is the worse washing machine ever. Wish Id never have bought it. Clothes come out unclean, washer cleaner cycle doesnt work, water level is almost none, etc etc. I could go on and on, you get the picture. Coming here and seeing 100s of negative reviews and complaints many of which I suffer from as well, just clarifies how bad this machine really is. There has got to be a way to bring a class action lawsuit or arbitrary suit against them. Im pretty confident that there are probably 100s more who are dealing with this shoddy washing machine as we all are.

First Maytag washer we bought in 2003, worked flawlessly for 14 years, bought a new one in 2017 only because my wife wanted a bigger washer. Bought a Maytag top load MVWB765FW0. What a big mistake. In less than 3 years it has failed already. The water inlet valve went bad. Maytag offers no tech support because they want to charge you with a service call. I found out what was wrong by researching the problem and error code online and bought the part for $55.00 and fixed myself instead of them charging $100.00 just to show up at your door plus the part and labor. A washer failing in less than 3 years is totally unacceptable and I will never purchase another Maytag/Whirlpool product ever again. Someone needs to wake up at Maytag.

First things first, Maytag Bravos washers are crap. Dont buy one. Purchased model # MVWB750WQ 06/12/2010 for $872.02 + tax. After 3.25 years the spin cycle started making extremely loud whining noises. Bought a replacement water pump for about $100 as several people were reporting the same issue. Before I had a chance to replace it the washer started leaking from under the washer. And not a small amount of water! Mats were getting soaked after each wash. I went ahead and replaced the water pump. But the whining noise, while diminished, didnt go away. And the leak continued. Based on what Ive read on this and other forums it looks like Ill have to replace the bearings for the tub. Not going to happen. Just ordered a Speed Queen washer for about the same price as the Maytag and I will never buy another Maytag (or Whirlpool) product again. Note that I purchased the Maytag at Best Buy. Its important that Best Buy take some of the credit for this issue as they are complicit in keeping these substandard products on the market.

I have a MFX2570AEM French door refrigerator. Like many others on this site I have ice building up under the freezer drawer. Water also leaks onto the floor. We keep a towel there constantly. We bought this refrigerator along with a dishwasher and microwave, all Maytag and have been disappointed with all of them. We thought Maytag made quality appliances, but my experience tells a different story. I havent called for service yet, but will later today.

On 11-10-10 I purchased a top of the line Maytag fridge. All had been great till we needed a part in Nov. of 2014! After nearly 3 months of searching they tell us that they no longer make parts for this unit and I am out of luck! Fridge works great but the center seal is broken (french door - Mullin) they quit making the part???? I am beyond angry! Will never buy Maytag again!!!

I bought a top end Maytag refrigerator with the freezer in the bottom drawer. Spending the extra buck was something that I thought was worth it, being a Maytag. Fifteen yrs go by and it stops completely. It cost me 200 bucks for a service technician to tell me that the compressor or it has a leak. Its not worth repairing. With todays cience and technology, you would think that they can make a refrigerator last for 25 yrs or more, like the old ones. We went to the moon 44 yrs ago. Why cant they make them to last? I think that the corporations figured they can make more money making an inferior product that needs to be replaced every 10-15 yrs. I will never by a Maytag again.

I purchased a Maytag Bravos HE top load washing machine from Sears in 2011. In January 2015, the machine stops at the spin cycle and wont continue the full process. The lid light comes on and blinks red. The machine made a loud grinding noise. A technician from Sears has been to my home 4 times in a month but unable to fix the problem. I have to take my clothes to the outside laundry. I have a protection warranty but it ends in a week. Im frustrated. Maytag Bravos sucks.

I bought a Maytag Bravo Series 300 washer and dryer for $2,000. The dryer is fine, so far, but the washer is dead. I have not received any answers from Maytag and the product is already outside of its warranty. I only had it for two years.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

The paint (stainless steel) on the top panel surrounding the digital screen is deteriorating from the heat and steam from light cooking. This happened the first time I used one of the back burners for light simmering. I purchased the range in December 2011, but had not used the back burners because I dont cook large meals. The black paint on the range top is also easily scratched when moving the grates for cleaning. This product has defective paint and Maytag has NOT responded to my questions sent to them by email. I will never purchase another Maytag product NOR will I purchase appliances from HOME DEPOT again. Home Depot should not sell shoddy products!

I purchased two high end Maytag machines, one washer and one dryer, approximately 36 months ago. I did not buy the extended warranty because I was foolishly convinced Maytag sold reliable products. The dryer required service twice within the first 18 months. The washer, which is computerized, is almost unusable. The sensors dont work properly. It does not spin without continual restarting the machine. It takes me hours to wash one load of laundry, and even then it is not spun properly. I wrote Maytag headquarters twice via e-mail, with no response. Even though their website says someone will get back to you within three business days. I called Maytag on August 12th and was told there is nothing they can do because I didnt purchase the extended warranty. So the bottom line is you can spend thousands of dollars on their machines but dont expect them to last, or work. And Maytag will not stand behind their products.

You would be better off going to the river and washing your clothes with rocks. Piece of junk. Maytag will have you believe that the six inches of water this washer uses to clean a comforter is enough. I would like to know which individuals in the dept of energy thought this water saving feature was a novel idea. What use is a giant washer tub if it doesn’t have enough water. Sorry Maytag, my clothes used to come out clean with your old model, now I spend hours trying to figure out ways to get this washer to clean. Currently I am using the clean washer cycle for my comforters and then using the deep water cycle. So it takes about four hours to do a load of clothes. Thanks Maytag! This Maytag Bravos XL washer stinks.

Ive had a Maytag washer and dryer for 10 years. They have worked well, havent had any problems. I bought Maytag because of their excellent reliability, which has proven true. Design is not as modern as others, and doesnt have all the features, but overall solid reliable washer.

My experience is very similar to Richards below. I have an MDBH979AWS3 that was purchased new in April of 2010. Just over one month after my warranty expired, the touch panel ceased to work. Since it was no longer in warranty, I had to replace it out of pocket. The wiring harness to the old panel looked heat damaged. Last winter, the central computer died. The machine was useless. I called Maytag customer service and actually seemed to find a sympathetic ear. They agreed to a new part if I paid $129 for one of the two companies doing certified repair to install it. During the summer, it blew several fuses. Then in late November of this year, the touch panel went again. I hesitated on how to respond and waited until after the holidays to call them. I got the most rude customer service rep that Ive dealt with in a long time. Somehow, I was blamed for a misdiagnosis on the computer panel (duh, no, that was a different issue and it was indeed broken), accused of misuse of the dishwasher, and flatly told that they werent going to do anything more on a machine. So far, out of warranty. Im sorry, but I cant accept that a machine under 3 years old should have 3 major failures. Maytag has to step up and at least look at this problem. From what Ive read, this is a common problem that has resulted in several fires. Maytag has to know about this and continues to do nothing, not even issue a recall on the current touch panel used. I am now faced with putting another $100 in (which puts me at about $350 total on a machine I paid almost $500 for) or just buy a new product. Rest assured I will never buy another Maytag-Whirlpool appliance.

We used to own a Neptune Model. After always leaving the door opened and following the recommended monthly cleaning and many extra cleanings with diluted bleach and water, we could not get the smell out. We paid for a new seal, Advice from Washing Machine Repair service even though we paid a lot for an extended warranty. We had to pay for this ourselves. We also had our year to year maintenance. Because we could not fix the issue, nor would MAYTAG, we donated the set to donated it to Salvation Army.We decided to give MAYTAG another chance, so we purchased a brand new FRONT-LOAD WASHER and DRYER in 2014. As I would repeat the same regiment, I would notice little black specks, so I would clean it an extra time with Afresh. I have continued to this date, repeating the same regiment of keeping my washer clean and serviced as we should, I now have the whole tray dispenser spotted with LARGE black goo that smells. So I have continued to clean my Washer.After returning home from the Cleveland Clinic, I was ready to do our laundry from the trip, more black goo and smell coming from my Maytag front-load washer. My sister had stayed with my 86 year old mother and had wash a load of towels while we were gone. She left the door opened also as she was instructed many times, and that is how we found it. So I took the dispenser tray out as usual and bleached it and scrubbed it. As I did this I noticed bigger areas of goo. I looked in the dispenser housing and OMG it was covered with black mold. I am appalled that our $900.00 Washing Machine is like this. This IS BLACK MOLD, There is no way to remove this mold. I have the sides and bottom cleaned with bleach, BUT I cannot get into the multiple crevices.I called Maytag and I was initially told by a Maytag Customer Service Person said that it sounds like BLACK MOLD and MAYTAG COULD DO NOTHING! I asked to speak with a supervisor. At first she seemed a little put off, but as we talked she became more pleasant, I offered to send pictures or a video of the WASHER WITH THE BLACK MOLD and she said no. She told me to pour bleach into each dispensing compartment and the drum. Then run a wash with no clothes on all HOT WATER 2 times, then rinse 2 times and this should get rid of it and to also leave the dispenser drawer open a crack as well as the door after each wash.The Supervisor said ok and thanked her for her help. Then she said good luck and thanks for calling MAYTAG. Ive did and already do everything our Washer manual says to do on cleaning and maintenance of my expensive Maytag Washer and dryer. The manual says nothing about leaving the dispenser drawer open a little so it dries. The bottom of the housing looks great from doing this, along with me scrubbing it until 5:00 am with diluted bleach water. However, in the MANY SEAMS, CREVICES, THE SCHUTE AND POSSIBLY THROUGHOUT THE WASHING MACHINE IS BLACK MOLD that we cannot access without disassembling the machine and voiding our extended warranty.MOLD GROWS RAPIDLY and causes many illness. I already have an ongoing illness since childhood, I take care of my 86 year old mother, my husband just finished cancer treatment in January. We certainly do not need any other health issues. I called my local Appliance repair company and they said that they normally do not handle anything like this, but if my husband couldnt take the outside of the machine off then the top I could pay for a repair person to come out to take it apart then call and have them come back to put it back, pay them again to reassemble our Washer.I believe Whirlpool in its purchase of Maytag has taken a Monkey on its back. Maytag will do nothing, why should they? They already have their money from when we purchased our machines along with money from many other consumers who also have ongoing issues with their WHIRLPOOL/MAYTAG Front-Load washing machines. It is undignified and deceitful how they treat their consumers with such disregard when we have filled their pockets by being loyal customers.Word of mouth is good or bad advertisement for any company. Everyone who has unresolved issues of any kind can write a formal complaint to the CEO and President of Whirlpool/Maytag. The address is on the internet. Shame on Whirlpool/Maytag for taking many consumers hard earned money, when apparently some of Whirlpool/Maytags money is ill gained by developing and manufacturing a consumer product that causes black mold and marketing it to sell to us, the consumer. THIS IS A SERIOUS ISSUE WHIRLPOOL/MAYTAG. OWN UP!!! My advertisement begins today!!!

This is the worse washer... As many other have complained I have the same problems. This washer it will not fill with water ever. It doesn’t rinse clothes or clean them as I’m use to the old washers doing. From day one I noticed the water does not fill in the tub and wondered how can the clothes be getting cleaned properly. Getting a F51 code and after going on YouTube and checking for problems it seems to say the same code after it works for a bit. This is the worse appliance I have ever purchased. I am so frustrated and will never purchase a Maytag anything again. Never did in the past up to this one and never will after this one.

I had purchased a brand new Maytag refrigerator and in less than a year, the ice dispenser stopped working. I had called Maytag warranty department in regards to this matter and they flat out said, There is nothing we can do about it. I will never deal with this company whatsoever and wouldnt recommend it to anyone about it. Less than a year and they refuse to fix the item they sold. No better than a used car lot attitude.

Shortly after having this appliance custom wired and installed into the kitchen cabinets above our gas range, we found that the microwave no longer worked. The window where the digital clock shows the time instead Showed SE. I hit the clear button and the microwave once again worked. This happened again on many occasions and the clear button corrected this malfunction. Now this has happened once again but nothing Ive attempted clears the System Error or reboots the microwaves brain. Ive contacted many appliance repairmen but as soon as I mention Maytag they inform me not to repair the microwave as it costs more to repair than to replace. Ive attempted to purchase a new circuit board and repair it myself but no one has the part available. This appliance was purchased in April, 2009. Can anyone recommend a Microwave Brand as a replacement for this disappointment?