I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

We have had our Maytag dishwasher MDB9100AWQ only 5 years and now it keeps shutting off. I see there is plenty of this complaint. I will not purchase another Maytag product after reading all these reviews and experiencing it.

Clothes do not turn over in the wash cycle. The clothes at the bottom get plenty of hard scrubbing from the agitator but the ones at the top barely get wet and never move down to the bottom. Insufficient amount of water enters the tub. The repairman says the washer is working as designed. Neither Maytag or Lowes will take back the washer. Worst appliance Ive ever owned. Bummer!

We bought a Maytag oven in Late October 2018. On January 22, 2019 the oven quit heating. Since it was still under warranty we called Maytag and they sent out a contracted service technician. The service tech said the circuit board had gone bad, and said it would be 5 to 10 days for part to come in. After a month the part still had not come and service tech was not returning calls. We called Maytag after another week and they provided very little help other than, We will contact service tech. Service tech never called us nor did Maytag call back. Called Maytag back on 3.10.2019 and asked how we could get this part and oven fixed. Customer service representative was not very helpful as they asked for part number which she was told was a circuit board and the tech they sent did not give that to us. After the customer service rep continued to provide any help other than say call service tech they sent out. I asked what if they replaced it for us since we have been without now for almost as long as we have owned. She stated Maytag does not do this except in extreme cases. I asked what is considered extreme cases. She stated she did not know. At this point I asked if she could transfer me to her supervisor and sat on hold for an hour, then had to leave for work. Very disappointed with Maytag and their lack of support to back their product.

We purchased our Maytag Washer back in August of 2019 and already needs a Motherboard and Lid replacement. Not only do you have to wait almost an hour to get a hold of their customer service I got hung up on once after waiting that long and the a Customer Service Lead by the name of Brittany couldnt offer any help either. We have been without our washer for almost a month now and will have to wait another couple weeks for the part to come in on top of probably another week for a maintenance person to come out and repair. I asked to expedite the part but that went absolutely nowhere. It actually added time to get the part because it was suppose to be here on the 13th but now its up to 9 business days for that to happen. I would stay away from purchasing any appliance from Maytag with the experience we have gone through and terrible customer service as well.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

Maytag Bravo Quiet 300 dryer(less than a year old): #1, on timed dry setting machine cuts off before the set time, clothes still wet. Needs multiple cycles to achieve drying, then you get wrinkles. Cannot manually set time, its automatic. Technicians (2) have replaced sensors and tinkered with timer, no fix, no documentation to show what was actually done.

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

We are in the process of replacing the 2nd control board in the past 2 years (have has this dishwasher for 3 yrs) on our Maytag dishwasher model MD87749AWW1. The lights on the panel completely quit working mid cycle. At $175 per replacement, we are into repairs for half of what we paid for the dishwasher. Bought Maytag because it is made in the USA but found out that a majority of the parts are imported from China? Very disappointing.

I bought 4 appliances - stove, refrigerator, dishwasher and microwave. Just after 1 year, our dishwasher stopped working. Serviceman said it was the motherboard. I had to talk with a supervisor in customer service to get it covered and found that it was only a switch that was bad. Next, our ice maker overflowed with water, causing damage to our new hardwood floor. Again, I had to talk with a supervisor to get this covered and I did not file a claim for the floor. Then, our stove shut down. Repairman found that a wire was shoved into the top box, causing them to be exposed and shorting out the system. Now 2 years and 4 months, our microwave is not heating and I have to call for service. This was a brand-new kitchen that was remodeled and all appliances were new.I am very disgusted with Maytag products and their attitude of We are sorry, but there is nothing we can do as the warranty has expired. It used to be 3-year warranties for Maytag products until they were bought out. Never will I buy their products again. Have been married 40 years, and our other appliances for 38 years never failed and to find that these products are made in the USA.

After the 4th service call Maytag wanted a 2nd company to look at it. So on July 27th A&E out of Bristol, PA came out. He checked it out and said its not serviceable because theres a leak somewhere in the casing. Had to call KYW 3, On Your Side, they helped me get some progress. Jacqueline from corporate called and said they would replace it. It started on July 3 and now August 13 and still no fridge. Had my Maytag washer fixed, small problem. Parts came in a box marked Whirlpool for a Maytag washer from a Sears Warehouse. Plus the mechanic said my Maytag refrigerator is made by Amana. Buy American?

I renovated my kitchen 3 years ago. I decided on purchasing new appliances which included refrigerator, dishwasher, microwave, range, washer and dryer, all of which I got from Maytag. Of course they were always known for dependability but apparently they were not! What happened to this American product? In the last 3 years, I have had my refrigerator (**) serviced 4 times for the same problem. Each time servicing has been a nightmare at the hands of AE service, Preway service and of course at the helm of my nightmare Maytag Customer service. The first mistake I made was purchasing Maytag products followed by the second mistake of purchasing Maytag service contracts. I now have a refrigerator that is not working, waiting on parts since end of august. When I called Maytag customer service, they confirmed the parts were not available and recommended I go online and try to find the part! This added insult to injury. Today, Preway service finally came to install my parts and upon technician’s arrival he opens the part box and realizes he ordered an ice tray cover, when he should have ordered an Interface Control Board. Maytag continues to have their products serviced by incompetent companies and appears to have no interest in keeping you as a customer after you purchase, whatever happen to the dependable people?Maytag had built their reputation on reliable products and dependable service, what happened to this American Made appliance? Here is a prime example of what happened, and why companies like LG and Samsung are gaining more and more customers every day. The best advice I can give someone is avoid Maytag. By the way, I forgot to mention I have 2 small children ages 3 and 4 and Maytag is not concerned about how I would provide food for them with a refrigerator that does not work. Shame! This is not what I expected from what I thought was a reliable company.

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

Im an 78 year old man, married in 1962. In all the years and two kids we have had just three Maytag washers. To me the gold standard of quality washers. When the motor went out in our 15 year old Washing machine I considered replacing the motor, which is well within my capability. I am a journeyman industrial machine repairman formerly with Ford Motor car company before retirement.Instead, my wife and I bought a Maytag top loader high efficiency washer from Best Buy. I was skeptical when I examined the new machine with paddles instead of the agitator. Trusting that Maytag had engineered a water saving washer using paddles, I made the very poor decision to buy it. I regret not replacing the motor in my old machine. Boy was I wrong. Given the chance I would trade my new machine for the old in a heartbeat...The old machine washed everything we could throw at it. The new machine wont wash anything to my satisfaction. The bedding deep fill cycle is the only one capable of a passable job. Even then I would like a soak cycle which, in my opinion, would vastly improve results. In all I would characterize this as a total engineering failure. Why Maytag would allow this POS to be sold, where the reputation of Maytag is totally destroyed, is beyond my comprehension.

This is the 3rd time my Maytag refrigerator has gone out on me and its only 7 years old! Its always the same thing, my refrigerator side starts getting warmer and warmer while the freezer starts forming crystallized ice. Both times its broken down in the past it has been the defrost timer. One service man said Maytag is not the reliable company it used to be and I would be better off buying a brand from Sears (Whirlpool or Kenmore) cant remember. Anyway, each of those services was close to $300 and now Im faced with another service call. We paid $2,800 for a refrigerator we thought would last decades. Well never buy Maytag again! I wish Maytag would own up to its cheap parts and send replacements to its customers with instructions on how to install!

Our less than five yr old washer finally died. It had been making awful sounds. Started in only very small loads but then started in bigger loads too. It finally stopped altogether. Model number MVWC400XW4. I would NOT recommend this washer.

I purchased a Maytag Dishwasher, Model MBD7609AWW2 from our local (small) Sears store in late 2011. I purchased Maytag because of reputation and experience with the brand. In June 2014 the control panel failed. I replaced it myself and the dishwasher worked fine for a little over two months. Today, it has stopped working again and the control panel again has gone bad and has to be replaced. Sadly, the dishwasher is great in cleaning dishes. I have only had to rewash maybe one or two items in the time that Ive had it. I purchased Maytag because my previous dishwasher was a Maytag that lasted 20 years. Granted I did have to change the belt twice but it was an easy fix. Ive tried repeatedly to contact Maytag today but they are experiencing extremely high call volume... HA! I wonder why? The dishwasher was warrantied for a year and based on the experiences I have read about online, this model was apparently an absolute failure. No more Maytag anything for me... I guess the Maytag Repairman is bored because Maytag doesnt stand behind their appliances.... anymore...

Every 3 months, the freezer compartment needs to be dismantled to unclog the defrost drain hole. When this occurs, it dumps all the defrost all over the base of the freezer which then leaks water out of the freezer door all over the floor. Clearly a design flaw and Maytag will not acknowledge this but appliance repairman says these are notorious for this. A $1700 fridge shouldnt do this. Never will I buy a Maytag again, a complete POS.

The salesman tried to convince me to purchase a Bosch dishwasher, but I wanted one with a fingerprint-resistant finish. That narrowed my selection to several manufacturers. This dishwasher has a food grinder in it. It gets my dishes spotlessly clean, and I have been very happy with it.

We purchased a Maytag dishwasher in January of 2011. Two years later the entire machine stopped working. We had purchased the extended warranty and the control board and panel were replaced. Now two years later it happens again. Maytag/Whirlpool is of no help nor do they care. DO NOT purchase their product!! Multiple complaints and issues with faulty control panels and the cost to replace one is the same as buying a new dishwasher so they cant lose. I will never again own a Maytag or Whirlpool product.

I purchased a Maytag refrigerator back in 2005; right around the time Whirlpool was making a play for Maytag. What a mistake! I had previously owned a GE that lasted 19 years! I even selected a model that did not have any ice in door or water in door that are prone to problems. In the 8 years I owned it, I had a serviceman to my place at least 4 times and dumped around $600 into it! Today the final straw... the compressor went! I will NEVER buy a Maytag again!

Shortly after purchasing my Maytag refrigerator had to pay for a new motor in the ice maker. The cover for the lower large food tray broke. Now approx. 4 years later am getting ice build-up on the bottom of the lower freezer unit, about one-half inch thick. It is enough so the freezer door wont seal when it closes and the inside builds up with frost. Not happy with Maytag or this refrigerator.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

We are on our 2nd Maytag washer with the 1st being a top load with agitator and the second without. Both were also bought used. The 1st one broke after I was cleaning it so totally my fault but the second one the door lock broke. Aside from that they do wash clothes well and but I do wish there were more or different cycle settings. Overall they are good machines for out price. (Being used that is.)

I purchased this washer in April 2017 from H/D. The machine started making funny grinding noise over this weekend. Had a tech come to house to repair. Tech said the insides are stripped, 300 plus in parts to repair and would be weeks to get parts. I called Maytag and they offered to send their own tech to see which parts and if any of them would be under warranty at a price of 109. I explained that I had an expectation that a washer would last longer than 31 months and spending another 109 dollars would be bad money after good with the 80 dollars for my tech. Maytag said take it or leave it. I am going to Lowes for a GE machine. DO NOT BUY THIS. IT WONT LAST. I will admit, Tina from Tennesse, the Maytag customer complaint person was nice and professional but not actually empowered to do anything to help. I will recommend to my 5 kids never buy Maytag.

I have been trying to get my refrigerator repaired for over 5 months through the extended service plan I paid for. They sent out a service repairman. He could not repair the refrigerator without some parts so he ordered parts. We waited months to find out he can not get the part anymore that he ordered. So now Maytag Extended Plans and Service Power said they would have to replace the whole refrigerator but every time I call about it, they give me the runaround and say someone will be calling me back within 48 hours.I never get a call back. I give them a few days, then I call back and get the same runaround again. Im getting nowhere with these people. My refrigerator is a $6,500 refrigerator that Im sure they just dont want to replace or offer me anything for that matter. They should abide by the contract I have with them.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

Like most people with this Bravos machine, I am 3 months out of warranty and the ball bearing is trash. When the wash goes into spin cycle, it makes a loud clicking noise and takes a few minutes to start spinning. I called service repair and he told me that it was the ball bearing and to talk with them as he has dealt with quite a few high end machines from Maytag that are breaking down after warranty. I should have realized there was a problem when we kept coming up with white spots on our clean laundry and would have to re-rinse clean clothes. This kind of defeats the water saver that is advertised with the machine.Do not buy this product. For a high end washer and dryer, there are many problems. Maybe that is why the Maytag guy is not shown sleeping in commercials any longer. Hes too busy fixing all these machines. Btw, they wont cover the part even though I offered to pay for the service. The best they can do is give me 25% off. Yippee! I cant wait for the other problems to hit me like everyone else.

We purchased the Maytag over the range microwave December 2014. Three months after installing it the door cracked. Maytag did replace the door and the repairman thought it might be due to the heat from the stove (huh, it was designed to go over the stove, where there will be heat). Now, six months after that, the layers of plastic on the door are separating and the piece around the control panel is cracked. Maytag agreed to replace the control panel but refuse to replace the door as it is only cosmetic (their words). So much for paying a little extra for what we thought would be a quality product. It seems to me that if something was made to go over the stove, it should be made to withstand the heat.

Maytag dishwasher model MDB4949SDE3: This dishwasher is the biggest POS that I have ever owned in 40 years. The first one would never turn on and fill with water and after it finally did it leaked on my new floor. Waited 10 days to have it replaced. The dishwasher cycle is 2.5 - 3.5 hours and the dishes come out dirty. The top rack is not adjustable to wash odd things. I feel that these dishwashers need to be replaced.

We purchased this Maytag washer. My wife liked it at first, but after a few months she kept complaining the wash stinks, and I can also say that. I complained to my wife about the smell of our wash, especially the wash towels. The wash was turning colors and some we threw away. My wife has been complaining about all this for months and years and said she will never buy another washer like this. Then about two years ago, she was having trouble with codes coming up. We called service, but didnt get any help, so I looked on internet and found the problem with the code. I took the washer apart and cleaned the tube out and the washer worked, but every now and then my wife needs to climb over washer and unplug, let sit, then replug back in and start it to get rid of code. My wife and I are very upset with this washer!

All in all I have liked my electric range, but I have 2 issues that I am having trouble resolving. I bought the range in 2003 and to find the model number I have to pull the range out from the cupboards on each side which would be extremely difficult under the circumstances. The reason I want to get the model number is so that I might find replacement parts for the doors edging that has flaked and rusted and is quite unattractive.

I purchased Maytag fridge a year ago and it has been a nightmare. The freezer doesnt freeze items. the drawers were all damaged upon receiving. I have contacted Maytag for more than 10 times and 5 techs came that I paid 125 each visit to fix the fridge because I didnt purchase the warranty thinking it was a good product . It is not! They dont stand behind their word. They lie and they send unqualified techs the misdiagnose issue to collect service calls. Please avoid this brand by all cost. My experience is terrible and I never want to wish it on anyone.

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

I purchased my Bravo Maytag washer, dryer set May 31, 2015. I spent a little extra because they were suppose to be so reliable and last for MANY years. What a HUGE mistake! The washing machine is rusting. (A friend said, although Maytag’s big promotion was Made in America the inferior metal probably came from China). Buy cheap and to “hell” with the consumer! As many horrible reviews as I have read about the Bravo Series of washers and dryers I am shock there has not been a recall or better yet, a class action lawsuit! Rusting washing machine and have had to replace a part on my dryer...of course all cost came out of my pocket. I will NEVER buy anything Maytag as long as I live. I have told and will continue to tell my friends and family my nightmare Maytag story!!!

Maytag Model # MMV4205DS - First Maytag microwave lasted just over a year before it quit. Replaced with same model to avoid install hassle and 1 year and 4 months later got the dreaded open and close door message. Read so many horror stories about repair service for Maytag that I decided not to bother and purchased a GE. I will never ever, ever buy anything Maytag ever again...

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

This product is not worth the money or irritation. It does not wash your clothes well and now mine wont spin. I have to completely unplug the machine and start it up to drain and spin. It takes 1 1/2 to wash one load of clothes. Its supposed to be energy efficient. Im pretty sure its not! I waste more time and electric doing a load of clothes than it takes to dry a load of clothes. Im dumping this thing for a real washer, one that works. I do not recommend this washing machine. I purchased the Bravo at Lowes.

The stovetop is very hard to clean and gets stained easily. The heat works wonderfully and the burners are great sizes. The left side with the adjoining burners is great. The double oven is fantastic. Heats relatively fast. Another negative is the button controls. You have to push so hard for it to register. Its painful. Not the best way to do it. Just setting oven temperature is difficult. Wish that was different.

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

I purchased a complete Maytag set for my kitchen (fridge, double oven, microwave, dishwasher) from Home Depot on November 22nd 2012. About two months ago I noticed the dishwasher started to glitch here and there, but was still functional. I removed the panel and found that the wiring was completely corroded and would need to be replaced. I put everything back together and have managed to make it almost a month on the same cable. In the mean time, I searched for my receipts, my manuals, and anything else to show my purchase given the 10 YEAR WARRANTY Maytag wants to mention as a sale point. Aside from Home Depot not being able to find my order information to duplicate the receipt, I managed to find where I had ordered my set online and was emailed a copy. Home depot is not involved with the warranty process, unless you purchase the additional warranty. They deferred me to Maytag. I contacted Maytag and was informed that the warranty only covers the stainless internal tub, the racks, and the chopper. Seriously?? So, absolutely NOTHING mechanical about the product past one year.After paying the $699 for the washer, and another 57.99 for installation and kit, I was told by Maytag that I could buy another 1 year warranty that would cover the part, but it would cost me $289, or roughly half the price I paid to get a whole two years out of the dishwasher in the first place. This means I might as well be paying almost $300 a year just to have this product... ridiculous!! Just to buy the part and do the work myself, the part is $172 plus tax/shipping. Since it is only 4 screws and a couple clips holding this thing on, I am likely going to go that route.I have read many people saying similar things about the electronic wire corroding and this appears to be a well known issue with their products. They recommend sealing the entire area using a tube of silicone to help reduce the amount of time it takes to ruin another cable. Very very very poor craftsmanship. Nice racket they have through charging people so much every couple of years for their products!! As my $4000 kitchen appliance set falls apart, I doubt I will ever replace it with another Maytag item.

Wow! I wished I had reviewed this page before purchasing a Maytag. We bought a new Maytag Range (#MGR5751BDD) from Menards in March 2008. Within a couple of months, we were out of a stove. I was lighting the burner to make dinner for my family (it is a gas range) and all the burners started making a clicking noise and they caught on fire. Luckily, my husband was nearby and took the fire extinguisher to it.We thought for sure that the house was going to be gone. We contacted Maytag and they had a guy come out (wasnt the friendliest and cted like he could care less). He stated there was wiring that was bad but because we took the fire extinguisher to it we probably voided the warranty. What? He would submit a report to Maytag.Maytag reluctantly gave us some money but not near enough to cover the stove that was only a couple of months old. Now, I cant use the new range that is 2.5 years old. It pops and spurts because the regulator needs to be replaced. The bad thing is by the time we pay for a repairman and the new part, it will cost us a lot of money we cant afford. This stinks.

We purchased our Maytag dishwasher less than a year ago and are very disappointed with the poorly designed quality of this product. We had a Maytag repairman look at our dishwasher and he told us that; the dishwasher cleans with enzymes in the dishwasher not water pressure, and we need to make sure the water in the kitchen faucet need to be hot before starting the dishwasher, we also need detergent, rinse aid, and citric acid added to each load. Adding all these products to the dishwasher does not fix a poorly designed product. This product does not clean the dishes, even with rinse aid the glasses come out cloudy. The dishwasher has a power blast button, it does not clean the dishes any better than the regular setting and it runs for four hours. We will never buy another Maytag product.

This machine is awful and a waste of money. Don’t trust the reviews with “workarounds.” That’s crazy! Doing laundry is difficult enough in my house so I need to add extra work? And they don’t work anyway. Water is barely 1-2 inches deep. But the real issue is the clothes don’t come out clean. Of course, they smell clean because all the soap hasn’t rinsed out but they are not. I spilled coffee on a white tee. Dabbed it up with a wet napkin. Threw it in the laundry. Did whites and added extra bleach and extra water because I know how much this machine sucks. Not only are my clothes yellow but the coffee stain is still there. I can’t imagine how it will wash tough stains like blood and wine and grease. I cannot even believe they are allowed to rip people off with this product.

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

I purchased high end Maytag washer, dryer, dishwasher and microwave in May 2010. On Saturday 4/25/14, the Maytag Microwave stopped heating. The fan runs, the panel, display, lights, clock, and tray all work. It just doesnt cook. The Microwave was installed in June of 2010. Not even 4 years old. I have tried to troubleshoot via the instructions that came with the microwave, i.e. Check the demo mode is not on. Dont know why after 3 yrs it would be, but checked it. No help. Pulled the plug out and replaced; turned breaker on and off; checked to see if its was locked. Nothing. I then checked the door and I found that the plastic inside panel on the latching side of the door is pulling away from the door itself, which is part of the locking system. The magnetron shouldnt work if the door system isnt closing properly. The latch system is what is causing the door to pull apart. I am wondering now how much microwave exposure my family has been getting from a malfunctioning door? I have had a Microwave, dishwasher and refrigerator made by Maytag in the past. The refrigerator is 14 yrs old and still works fine. The microwave and dishwasher were at least 10 yrs old when I replaced them with the new Maytags I have now. Here is the problem. Maytag is not Maytag Corp. anymore. Whirlpool Corp now owns the Maytag brand. Prior to the old Maytags I had, I had GE fridge which was junk, and Whirlpool, dishwasher, stove and microwave. They were also junk. I swore I would never buy Whirlpool products again. Surprise.

My dishwasher is less than 2 years old. Dishwasher will go on when we are not in the house. Cant control the panel. The control panel lights all come, have to cancel to stop the machine. This could be a fire hazard.

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

This Maytag refrigerator is a counter depth so a little smaller in the Inside than I would like but fits in my tiny kitchen great. It has an inside water dispenser which is so nice because it keeps the clean look on the outside. It’s a year old and so far I have not had any problems with it.

I would like others to know that Maytag does not stand behind this product at all. I am not sure about other products, but after talking to Maytags customer service team I would guess you would get the same runaround with other products. We have had our washers for about eight years now and have had many things go wrong with it. The one that gets me the most is the one that my appliance repair service does not cover and that is the main bearing. I have done some research to why this is and most of them do not cover this, because they should last for the life of the washer. Most washers last for more than ten years. However this washer has only lasted a few years on each bearing. I have now put in my third bearing into this washer. The last bearing only lasted two years. If I had to pay for labor on replacing this part I would have not replaced it. I had been given a quote for replacing it and it was over $350. Some places wanted more than $400 to do it. To me the washer is not worth this. Yes we paid like $900 for the washer, but it is not worth putting that much money into this washer. If you cannot replace this part on your own then just walk away from it. Buy a Speed Queen. I know Maytag has sent parts to other people free of charge, but I have not been so lucky. When you send others part to fix the same problem, to me that is admitting that there is a flaw in this washer. With that said my wife and I already filed a BBB complaint against Maytag and will be sending a letter to the Minnesota Attorney General. I have proof they have sent replacement parts to others and dont see why they cannot do the same for me. Maytag is own by Whirlpool, you think it would be cheaper and easier to make customers happy than just brushing them off. I would say that customer service in many of these large companies and even small companies is gone. I remember when you would call a company and make a complaint and they would go out of their way to try to make you happy. Now they come up with reasons why it is all the customers fault that their products are bad. Maytag is just another example of a greedy business that does not care about their customers. So please do your research before you buy this product and good luck to those who have that are stuck with the junk that Maytag sells customers.

We purchased this set 6 months ago. The store we purchased it from is unwilling to help us. Maytag insists there is nothing wrong with the washing machine. The machine doesnt clean the clothes. After a wash cycle there is pet fur and lint all over the clothes, even after it comes out of the dryer. The clothes are all twisted in tight knots when the load is done. The washing Machine doesnt dispense enough water to wash. I have taken clothes out of the washer and the items are dry in spots, most times you can smell the mustiness of a dish towel after its been washed.I used the steam clean dryer to fresh in up the curtains and the panels came out different lengths. Not eager to try that feature again. This is our 2nd dryer set purchase, the last set was 10 yrs old. I couldnt find anyone willing to repair it. I was told they dont make machines like they used to and they are all designed to last 10 yrs and you’re lucky if it lasts 15 yrs. Yes, we contacted Maytag and yes, like the many other folks who have shared their stories we also got the run around. Sad to say we are going to do our research and will be looking for a new machine. Im going to shamefully donate the set to a charitable organization and use the receipt as a tax write off. IF you’re doing your research, DO NOT BUY A MAYTAG.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

Maytag Dishwasher, mdb7749sam1 - I got this dishwasher new in Feb. 2013 for my new house. I thought that Maytag was supposed to be a very good appliance company. (I just found out that Whirlpool bought them! I dont like their dishwashers, either! Ive had 3 whirlpools that only lasted about 2-4 years each.) My dishwasher worked great until the control panel buttons started blinking and going crazy! Then, it just stopped working altogether. I called Maytag about this part, and found out that it is only covered the first year, and the so-called 10-year warranty doesnt cover it. What good is the extended 10-year warranty if it doesnt cover all the parts!? I researched this dishwasher before I bought it. It got fairly good reviews at the time. Now when I look it up, it gets these terrible reviews! I am so disappointed with this situation. I have other Maytag appliances that have performed great. Im not sure why their dishwashers cant be made the same way.I am going to order the part and repair the machine. I hope this will fix the problem. I had hoped that the Maytag brand would live up to their hype, and be better than the Whirlpools I had already had such bad experiences with. The Whirlpools had great features, they just didnt last! This dishwasher, too, has great features. Two years isnt a long enough run for it to be a good choice, though. Really disappointed :(

Worse washer ever, clothes are dirty and smelly. Customer Service is even worse. After a normal cycle clothes come out half wet, never enough water in the machine. Everything gets washed on bulky and there is soap residue on everything. Have taken clothes to the laundromat on several occasions just to get them clean. I cant wait to get rid of this piece of crap!!! Never ever buying Maytag again!! Warning to everyone... DO NOT BUY THIS MACHINE!! And with the extended warranty, they still dont cover it. :(

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

Maytag Bravos XL Washer & Dryer - After a long 45-year use of our old GE W./D. that were still working fine when we decided it was finally time to upgrade. Big mistake. Nothing but dissatisfaction on every level of complaints by those who registered here before us and then some. This all was noticed almost immediately after purchase, but we lived with it trying not to believe our worse fears. That is until we both started breaking out with skin rashes. Just logged on this site after a Google search... We were shocked and disappointed in our purchase decision. We will join in a class action lawsuit if ever one is initiated... Any lawyers with one of these?

Maytag top load washer. I dont understand why Maytag would make such a piece of crap. It takes so long to wash, that I can only wash a couple of loads a day. It doesnt fill. It doesnt get the clothes clean. My electric bill is higher. Its so noisy too. Never thought Maytag would make such garbage.

In the winter of 2007, we remodeled our kitchen and bought all new Maytag appliances. They cost a little more but we felt that we were getting a good quality product. Within months, the handle on the freezer became loose and I had to call for a repairman to tighten it. He told me we should buy the extended warranty because only a trained repairman could fix the handle. That turned out to be untrue thankfully because if it was true, I would have to call for repair at least once a month. The handle is constantly coming loose. A few months later, the microwave would turn on when the door was closed. I called repair as it was still under warranty. After he removed and replaced the door, I was told that we have to be careful when we close the microwave. There was nothing he could do to stop the problem. Approximately three years after we purchased the appliances, we had a problem with the dishwasher. We could only use one function; the others would not work. We were told by the technician that we got water into the door where the controls are and ruined the motherboard. I never heard anything so absurd. I have had a dishwasher in the same place for 25 years with no mishap. The cost of repair was $800. A few months later, we had a problem with the large burner on our cooktop. The outer coils heat up but the inner coils do not. I have yet to call for repair because I do not trust Maytag. Now, our microwave does not work. My husband used it to make popcorn with no problem. A little while later, I tried to heat a cup of coffee and it would not heat. The keypad works, the light comes on in the microwave but the motor does not run. Needless to say, we are very unhappy and will never buy another Maytag appliance. I wish I would have read the reviews before we purchased the appliances. Two of our friends had their kitchens remodeled at the same time we did and they have not had any problems with their appliances. But they didnt buy Maytag. I guess thats why.

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

Just purchased a Maytag French Door Refrigerator and am I sorry I did! Very noisy and runs continuously. Maytag says it is because it has high-efficiency compressor and fans? How is running continuously efficient? The continuous noise actually keeps me awake at night. Not sure what to do as I have spent $1700. :(

Used my washer ONE time and when the load was done my clothes were soaking wet. Tried to get the clothes to spin dry but the washer would not work. Called for repair. They replaced the activator. I did one load of laundry. It worked fine. Did a second load of laundry and the clothes were soaking wet. The washer would not do anything else.

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

I purchased my Maytag Neptune pair on Jan. 24, 2005. I was unaware of the problems and lawsuit related to these items. Luckily, I didnt have any problems with them until May of this year. At that time, I spent $337.00 for a new control panel for the dryer. (Just because I didnt want to split up my set.) I expected them to last me for the rest of my life. Of course, the washer had started to do something even the repair man had never heard of before, right about the same time. I told him that the tub would fill up with gallons of water, and surprise me when I opened the door on various occasions, flooding my laundry room and the basement downstairs. Mind you, this would occur even with the water supply cut off to the machine, no hot or cold running to it.He performed a diagnostic test on it and said everything showed up fine. Of course, it didnt overflow while he was here. He is the one who told me about all the trouble and the lawsuits. I had wondered why I didnt see them for sale anymore. I have been keeping the water turned off except when I need to use it after all this time. It still happens! The repairman thought I was senile or something. I dont have a mold problem, no trouble with the door lock (yet), and out of all the comments and complaints Ive read online today, only this site had one with a problem of it flooding the house. My husband and I are on a fixed income, and here is this unit (that I thought would be my last) rotting out my floor and wall in the laundry room, and flooding my basement. Not to mention it rusting out the inside of the washer and its pedestal. I would like to hear from anyone else who had this water problem, and what it took to fix it.

Both work good. Washer could be a little lower and it has quit rinsing and I cannot use it. But it is 9 years old, I think for their age they were a good buy. I plan to get the washer repaired because have been satisfied with how clean it gets my clothes and it washes pretty quick. I got the large capacity and with a very large load the washer gets them clean. The dryer is very good. It is just as good on a large load as small, dries quick. I would buy this type washer and dryer again and would definitely recommend it to folks. I have been very happy with this washer and dryer. The paint is coming off the washer where you put detergent and fabric softener in and it has rusted out some but it is getting a little age on it so this is expected. I like it, I can throw my comforter in and it gets it clean and the large loads always come out great. I think anyone who bought the set would be very happy with it. It is also quiet which I like.

We purchased this washer (MHW05500FWD) and dryer set in 09/26/2016 and have had nothing but issues. I have had the repairmen out twice. The first time the washer wasnt rinsing out clothes, when the repairman came out he couldnt find anything. In June of 2017 the same thing happen. Once again the repairman came out. I found out that there was a recall on the part which was on Backordered. Now the matching dryer model MED5500FWD is not drying. This is the worst washer and dryer I have ever own. I will NEVER own another front loader again. Buyer Beware!!!

I bought a new Maytag stove and it is less than two years old and the oven has already quit working. It only has a one year warranty and will cost about $200 to fix. I am very dissatisfied with what I thought was a good product.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

My dishwasher racks are disintegrating. I called to see what to do or if there was a recall. I was told that problem happens a lot, but there is no recall or other option other than to purchase new racks. I could almost buy a new dishwasher. I bought Maytag so that it would last a long time with few repairs. That has not been the case with this dishwasher. I had a medium grade Sears’s dishwasher for years before I supposedly upgraded to a better dishwasher. Maytag is obviously an overpriced name and the quality of their product is no better than any other cheap dishwasher.

Our current dishwasher was already installed when we purchased this house. It is adequate, however, it does not do a great job with caked-on food. This means that the worst dishes need to be pre-cleaned.

Maytag Centennial Impeller HE Washing Machine - The seller left this piece of junk for us. I wondered why because it appeared brand new. After the first washing I knew why. I sure regretted leaving my old set behind. This washing machine wont let you add the amount of water you need. I had to add buckets of water and hope it didnt just empty it out because the sensor controls everything. Twice it just emptied it after I closed the lid and it locked. There is an impeller instead of an agitator. It moves slightly but not enough to move the clothes. To top it off the spin cycle tears into the clothing and twists and wrings it so hard everything is wrinkled with soap residue remaining even on delicate. Each load takes over an hour and the clothes arent even clean. It went to the dump after 4 washes. I went on Craigslist and purchased a used Kenmore and am in heaven. No lock, an agitator, 3 water levels, clean clothing, you can open it and add the missing sock, no sensor controlling how you want to do laundry and no more buckets. Dont buy a Maytag. Look at all of the reviews. They arent exaggerating, they are really that bad. Thank you.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

Bought this as W/D set brand new from Home Depot. Had been noticing incredible wear and tear on clothes, as things get so tangled up and need to be practically ripped apart before going into dryer. Cycle times are crazy long, up to over an hour in some cases. Doesn’t have a “Speed Wash” cycle. But WORST of all, after less than 3 years, it just stopped draining properly. Tried all the Codes test, etc. Finally called a repairman just to be told repair costs would probably cost more than the machine is worth. $125 to be told we ought to just buy a new washer. Not happy.

We purchased our Maytag dishwasher (model MDB7609AWW2) on November 14th, 2009 from a local appliance shop in White Plains, NY. Total purchase price was $449, not including tax.Sometime in November of 2011, the unit stopped working. I tried every simple test I could think of to hopefully reset the unit. Finishing the obvious checks, I researched some possible problems on the internet latch micro switch, drainage problem, dirty latch, etc. Frustrated as nothing got it working again, I called a repairman recommended to us by the appliance store.The repairman charged me $75 for the visit just to tell me that the control board is shot. Even worse, and this is the reason for this letter, the part costs $329 plus $40 in labor! That is outrageous! If you do the math, I am facing the costs of a brand new unit to fix the old one. That might make sense if the unit was 8 years old but it is barely 2.I have sat on the decision now for a few days as I am beyond upset and I never make good decisions when I feel like this. But to recap, Maytag manufactures an appliance where its basic function - turning on - fails in 2 years and the repair cost essentially totals (to use insurance parlance) the unit. I find this absolutely unacceptable.I don’t expect Maytag to do anything for me. But I will say this; I plan on letting everyone I know just how this experience went. To make things worse, I am willing to pay for a quality unit but how does anyone know what that is anymore? For color, my grandmother has a KitchenAid dishwasher from the 1970s that is still running fine. No membrane controls, no delay functions or fancy BS super sanitary cycles and guess what, it has no control board, just plain old dials and buttons. Imagine that mechanical control? Built to last unlike the junk you see today.To remedy, I plan on picking up a used machine from the classifieds. I’ll install it myself and be able to do this for 9 years at $449, assuming it only lasts one year (I’m finding these units for $50 used). I may get lucky and find an old one from the 70s that will last a lot longer than that.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

Purchased my microwave in 2005 and seldom used it. However in the last few months, the halogen light which lights up the range surface has been flickering. When I asked an electrician doing other work around my house to repair it, he discovered that the halogen light is attached with a dual pin socket which is plastic. When the halogen light gets overheated (and halogen produces alight of heat) it melts the plastic. It has already melted some of the plastic socket. When it fails to operate, I will have to repair the light socket which will be very expensive or buy a new microwave. This microwave cost $800 or more because it offered convection cooking which I have seldom used.This is what is presumed quality appliance? Plus I added the cost of an extended warranty.

My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

I purchased this dishwasher at least 12 years ago and it still works. However, after that much use some of the buttons no longer work. It has china, economy, regular, rinse only and extreme wash features.

I bought a Maytag laundry set (washer and dryer, models MVWC565FW and MEDC555DW, respectively), and I concur with the fact that this is the WORST laundry set I have ever owned. The clothes came out of the washer extremely dry and did not come out as clean as expected. In addition, clothes came out with strange spots, especially the dark ones. Now, we wash our dark clothes with fear of damage them. The dryer is also pathetic. I put in a normal load on high for 60 minutes, and theyre still very damp. Sometimes I have to repeat the cycle 2 or 3 times. When I compare it with my old laundry set, this is extremely disappointing. And to make things worse, the customer service department doesnt answer you. I sent them a mail, on February 2018, and a month and a half later, I havent heard back from them.

I have a top load commercial tech washer with an agitator that is brand new as of September 2019. I have done all of the troubleshooting suggestions and nothing works. I use 1 tsp of liquid cold water detergent, deep fill, extra rinse, and clear liquid oxi and my darks still come out with white stains. I have had a Maytag tech check out the machine and it checks out without issues. I would never recommend this product to anyone!

I positively HATE the new BravosXL Maytag washer, which has no decent agitator. It is ruining my clothes, as it spins with little water and leaves soap residue all over the clothes. Additionally it puts large, long wrinkles in my knits, especially disfiguring slacks. Maytag must have known how rough and ruinous this washer was on knits BEFORE selling it to an unsuspecting public! I want my money back in order to purchase an old-style, well-functioning agitator washing machine.A class-action suit should be brought against Maytag. There was no way to know before buying and using that this machine is horrible!!!

Like so many others, I now discover, we are having a ridiculously frustrating problem with our Maytag dishwasher, bought one and a half years ago. Last week, the control panel stopped working -- we press normal and a whole bunch of other lights come on; try to press other cleaning options and entirely different ones light up again. Sometimes we can get it, with luck, to quick wash or super clean and thus have our dishes cleaned (which the machine never did that effectively anyway); sometimes we cant. I havent called the company yet, but given what Ive read, Im unsure if it would do any good. Judging from all the similar comments, Maytag is clearly selling a radically inferior product and care nothing much about this. We will surely never, ever buy another one of their products.

I purchased a refrigerator 9 years ago and the ice maker stopped working. When the repairman took it out there was plastic peeling from the ice mold. It cost $261.11 to have the ice maker replaced and the ice maker he replaced it with has the plastic on the ice mold. He said that GEs ice makers do not have the plastic coating but Maytags still do. I called Maytag and spoke to a supervisor and they said that there was nothing that they could do. I am filing this complaint because I feel that consumer need to be aware that they are ingesting plastic that is in their ice. I feel that Maytag should compensate me for the faulty part and also eliminate the plastic coating from their ice maker. This issue is impacting many other consumers and they need to issue a recall on the ice maker and replace it for free for other consumers.

Stay away from this product!!! Lets just say one star is too much for this product. Terrible. Lets just say one star is too much for this product. We bought this washer 2/2017. We used our previous Maytag washing machine for about 15 years without any problems. But this machine on the first try was a big disappointment because it did not wash clothes very well. Clothes come out of washing machine smelling bad and you could see the soap scum on darker clothing. We try to return the machine to Home Depot after 3 days, but they said after 48 hours they could not take it back. So if there was any problems we had to call a technician to repair it. Well, there is nothing to repair because thats just the way the machine is designed to conserve water.Worst washer and the customer service is even worse than this machine because they just keep repeating that if there is nothing to repair then, there is no problem. So, therefore its not their responsibility. TERRIBLE!!! I even bought their extended warranty and that doesnt do anything with dissatisfaction on this product. If you are owner of this company or at least care about your company, you should stop making this kind of product, and listen to peoples complaints!!! What a waste of our hard earned money in this bad economy!!!

We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

DO NOT BUY A MAYTAG BRAVOS MCT WASHING MACHINE!!! I have had the machine for two and half weeks, it HAS NOT WORKED EVEN ONCE!!! Service was scheduled - again for a BRAND NEW machine - through Maytag/Whirlpool - and the service ordered never happened. We waited an entire day, 8 am - 4 pm, only to discover the service desk of Maytag doesnt work either. My service is now booked for another week away and I am working on returning this AWFUL Maytag washing machine which never worked even one time!!! Warning: Do not buy Maytag/Whirlpool appliances!!

We purchased a Maytag brand thinking it would be a quality long lasting machine. Wrong, the washer shakes from day one, We complained to Lowes, they brought out and installed a second unit, it does the same. The clothes dont get clean, sometimes you can see the blue HE Tide still on the clothes (sheets) after cycle is complete. Junk, waste of money, Ill never buy another Maytag product again. Dont waste your money on a Bravos Maytag top loading HE machine.

I hate my new Maytag washer and wish I had never purchased it. Theres no way to control the water level in it, and on sensor mode, the clothes are barely wet and rubbing against each other creating wear. Things come out with soap stains and twisted up so tight that I dont believe water got close enough to the dirt to carry it away. Dont waste your money.

Like so many other people reviewing Maytag refrigerators with bottom freezers, I am dealing with water on the floor. At 64+, I am not eager to tackle the problem as a DIY project. Once of defrosting and cleaning up was enough. I love the looks of my 2 yr old $2000 4 door fridge/freezer but hate the issues. I guess Maytag is going to ignore all of us. When someone finds a reliable company, sing it from the rooftops.

Fridge Model MFF2258VEB6 - Our refrigerator is less that 2 years old and it wont make ice! The bottom of freezer is filled with water that froze. Everyday there is water on the floor. We asked at Home Depot where we purchased it and they said we need to change the filter. What filter? The owners manual is a joke. We cant figure out where the filter is located so it looks like we have to pay money to have someone come look at this. Hey, this is ridiculous. I thought Maytag had a good reputation and thats why we bought ALL Maytag appliances two years ago! Never again!

I purchased a Maytag stainless steel French door model the middle of 2006. While cleaning the French doors with the cleaning product given to me with the purchase of the new fridge, I notice what looked like coffee on the doors. It wasnt, it was rust on the stainless steel doors. I called the service tech and they came out. Rubbing the fridge, he told me it wasnt rust. He took a closer look and found that it was in fact rust. He called his office; they told him that rusting on the doors has been an issue lately. He charged me $65.00 for what I already knew. I called Maytag and it took a while, but they decided to send new doors. However, I had to have a Maytag rep install it, which would cost me. I didnt have it done. Two years later in 2010, the French doors felt hot to the touch and the inside was warm and not cooling. The freezer was fine. I called for a tech to come out and it’s another $65.00 to fix a fan motor that blows cool air from the bottom to the top. Oh, it’s not under warranty because it wasnt inside with the motor. Total cost: $235.00. In 2010, I woke up and opened the fridge to get milk out. It was warm and so was the inside of the fridge. I thought it was the same problem, but the freezer also was warm. Upset and not wanting to pay for this again, I unplugged the thing and started using a little fridge that I have stored in the basement. It has no freezer. Today, I finally got over being pissed and decided that I would have a tech come out and find out and finally fix it. The tech said that the compressor has failed and it would cost $790.00 to fix. Im not having it fixed, so it’s another $65.00 gone. The tech said that the compressor in Maytags/Whirlpools has been a pretty big issue lately. All I can say is that I will not ever purchase Whirlpool products again. From inside to the outside, this product has been unsatisfactory. I just noticed that the rubber is failing on one of the French doors. Wake up, Whirlpool. Model number is MFD2561HES.

Purchased our dishwasher 11 months ago from Lowes. Dishwasher has a 10 year warranty on racks and 2 other items. We are 2 adults in the household. Dishwasher is maybe used 4 times a week. Very light use! Circulation pump is bad which also took out the dishwasher solenoid. Im not going to fix because it if only lasts a year again that is a very expensive repair. Very disappointed in this made in the USA product. That was the reason I purchased it. Made in the USA. Come on Maytag. You can do better than this!

My dishwasher is 9.5 months old. The computer board needs to be replaced and they cannot find the part. It’s been 2 1/2 weeks since I called in the repair which is under warranty. I was told they have 10 business days to search the country. Really search the country. Does anyone know what will happen if they cannot find the parts I need?

I purchased the Maytag MFI2670XEM0 3 Door Refrigerator in Oct 2012. Thank God I purchased the extended warranty. The freezer has had issues with improper sealing since I bought it. It builds up ice around the bottom of the freezer where the seal meets. So bad it prevents it from closing. It happens fast, so I have to scrape it off every week minimum, to keep it closed. They have replaced the seals twice, all of the slide rails, twice and it still doesnt close right. I thought when I moved to Florida, I wouldnt have to scrape ice.Next: Ice maker quit working and had to replace that. Now, I came out this morning and about busted my ** when I slipped on all the water flooding my kitchen. The ice maker has a stupid little fitting on top of the refrigerator that has a rubber bulb connected to the ice maker water line. It split in half and every time the ice maker cycles, it pours water out that fitting and down the side. Why in the ** did they design it like that? It has caused damage to my cabinets and tile floor from running under it.Im sick of this appliance. I thought Maytag was known for quality. What happened to that? What a disappointing piece of junk and Im stuck with it unless I want to put out money for something different. There should be a Lemon Law rule for appliances like this. I have asked and get nothing from the warranty service but silence (crickets). They are sending out a tech again but that will require two service calls because they always have to order parts, which takes 2-3 weeks. Ive had to call them at least 5 times, which has amounted to no less than 10 service calls and here we go again. Stay clear of these units at all cost.

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

My stainless steel french door refrigerator started to rust 4-5 months after purchase. Upon contacting Maytag/Whirlpool I was advised that this is cosmetic and the cosmetic portion of my warranty is expired. I think this is a poor grade of stainless steel and should be recalled and/or replaced. I would not recommend.