I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

Purchased the Maytag Bravos washer from Home Depot in August of 2011. Today it caught on fire (Sept, 2014). Had problems with it from the start. Some of the issues include the washing machine constantly getting off balance even with small loads, not completely draining the water from clothes resulting in having to run additional spin and drain cycles, and a bad odor coming from the water that stays on the clothes (we even called a plumber thinking it was something with our plumbing). Well today was the best. I started a small load (one twin flat sheet and a pillow case) and about 10 minutes later I smelled a weird burning odor coming from the laundry room. When I opened the door to the room it was filled with smoke. The washer was the only appliance running, otherwise I would have assumed the dryer was the source of the smoke. When I opened the lid to the washer, smoke started pouring out from around the inside drum of the washer. It smelled like burned rubber and ash. Needless to say, I doubt this washer is worth repairing. We actually have had repairs on it previously (twice in the first year) and its just a piece of junk. Glad I was home when the washer caught on fire. I hate to think what would have happened if I had not been able to unplug it and it continued burning. Do Not Buy This Brand. Definitely do not run this washing machine unless you are home to monitor it. Maytag Bravos is a fire risk!!!

I have just joined the open and close the door Maytag Club. Purchased four Maytag products on Black Friday 2017 as I always trusted Maytag. Only disappointed to have my microwave (MMV4205D-4) come down with the virus (open & close door) that has plagued so many unsuspected owners. Almost made its 1st year anniversary. Now I see this has been going on for years and all they do is add different model numbers at the end. Luckily Im in the 1 year warranty and repairman coming next week. Now I question if I should take the extended warranty as I see this is going to happen again down the road. And will the extended warranty cover it? Guess the Maytag repairman isnt sitting and waiting for repair call anymore. He is being kept busy!

I am angry that Maytag puts out a washer that hasnt been through quality control. The computer panel is a piece of **, and is not worth $1.00. Do not buy this washer. Shame on Maytag.

We bought a Maytag dishwasher in August, 2014, and already the touchpad is malfunctioning and we cant start the dishwasher! I am very disgruntled and frustrated by this! I should have kept the old Kitchen Aid dishwasher that we bought in 1995! At least it never malfunctioned!

Maytag MCT Washer & Dryer - I bought the largest capacity to save time. However even my 6ft tall husband has problems reaching the bottom to remove clothes. Even worse is the lack of water to clean clothes, washes so long it wears clothes and they are still dirty. I tried to improve on my old Neptune and Id love to have it back. I may have to junk this washer. The dryer is very slow. Buying this set was tossing my hard earned money in the trash.

I had the exact same experience as the Tampa person with my Maytag dishwasher (Model: MDBTT60AWW). It was not cleaning the dishes, even when I thoroughly rinsed them. Plus, it started leaking midway through the cycle. Since the warranty was expired, I purchased an extended warranty in July 2012 for $296 (yes, in hindsight, I should have just bought a new appliance, not Maytag). I had 3 visits from 2 different technicians, both telling me the dishwasher did not leak. One telling me I was using the wrong kind of detergent and thats why dishes werent getting cleaned. The other telling me that there were too much suds and that could cause it to leak. So, I should pour a tablespoon of cooking oil (yes, cooking oil) in the dishwasher when it starts leaking and that will cut down the suds. I dont think so!Then, I found out a couple of weeks ago that this model was under a recall since 2010, not related to the leak at all. Yet, Maytag still sold me the extended warranty (wheres the ethics of that?). I requested a pro-rated refund of the balance on the warranty - and wouldnt you know that with the technicians service calls, the amount of time used on the warranty (6 months) plus an admin fee - I have used $296.48 of the warranty amount. It is almost to the exact penny of what I originally paid, so I will not be receiving any refund. They are only giving me a debit card of $150 or $250 once I buy a new Maytag to replace the recalled model. I do not want to continue down this frustrating path known as Maytag appliances.

I bought my first centennial washer less than four years ago, warrantied that machine out. It was replaced by best buy because of the warranty that I purchased. We are a family of four, with that in mind the replacement machine was a model year newer and it last just over a year and quit. I bought the machine anticipating that it will last me the next 10 years. With two children at home now that is not working, all I have to do on replace a new machine. The repair shop has told me that they get more of the Maytag centennial machines and then any other washing machine is going to cost me more to repair it than to buy a new machine because I had faith in the Maytag products for many many years. This particular machines are extremely hard to diagnose as to what causes the problem or what the problem is and could take a long time to get it fixed as well as the expense of getting it fixed. I would not recommend another Maytag product nor will Maytag ever get any more money from us. This particular product has become a piece of junk that I cant even get rid of to recycling. Maytag has become a joke and this machine has become a 500 dollar hunk of junk in my opinion.

I purchased a Maytag Neptune Washer in 2006 for $665.00 from Sears. Three years later, the control board broke and I paid $400 to replace it. In 2011, the motor and motor board need replacing which will cost $410.00. We kept getting an LR code. So in 5 years, our repairs cost more than the original machine. Maytag can count on never getting my business again. Im only sorry that I purchased a Maytag dishwasher this Summer.

Gave up a very good old washing machine to update to a newer one and so we got the Maytag bravos 300. I thought Maytag was a very dependable name and product. The warranty went out. 2 weeks later, the water pump went out. I had to pay to have it replaced. Then after that it started making noise that got louder and louder and now it sounds like a thrashing machine. And now it has started leaking water out of the bottom. So its going in the scrap pile. What a loss of money - the worst investment I have made. For what I paid for this machine, it should have lasted for many years to come. The washer I had before this Maytag I had for 16 years - no problems at and it still worked great when I gave it away. Maytag use to be a brand you could count on. Great craftsmanship has been taken away and monetary gain has taken over. I hope no one else has to go through this nightmare that I have. Maytag they should have to give peoples money back that we all worked hard for. Going with a LG now, hope its a good machine.

I built a new house in 2006. As part of a builders package, we had all new stainless steel Maytag appliances installed. The side by side refrigerator compressor stopped after 26 months (of course, passed any warranty). No customer support through Maytag and as previously posted very scripted responses. Maytag microwave handle has broken off several times, the glass seal in the oven door was compromised and the inside glass is stained - most recently the on-going issue with my Maytag dishwasher model mdb5601. Ive already replaced the handle /door latch assembly twice and am confronted with the current dilemma if I should replace the control panel that now appears not to be working. It goes without saying that I will never purchase Maytag products again. However, I am not in a position to replace what are fairly new products. That being said, I am reluctant to purchase costly replacement parts given their poor performance and ratings as mentioned in this thread.

My 20 yr old Kenmore washer broke last month so I replaced it with a Maytag I bought from Lowes. I wanted a simple washer that would maybe last 10 years. The Maytag has a sensor for everything. So you can’t fill the washer, it determines how much water to use and it never fills enough to cover the clothes. It doesn’t agitate really. It’s more like a slow on & off movement. It does everything in an on & off way. The water fill goes on & off, it “washes” on & off. Even the spin is a spin, slow to almost stop - spin again - almost stop - spin again. It also stops filling if you open the lid, I tried to let some water fill before adding clothes (so the liquid detergent could dilute a bit) but every time I opened the top there was no water in the drum, I heated the water running and the drum was wet but it wouldn’t gill at all. I think it only puts water enough to “sense” the clothes have been soaked. I will call Lowes and try to return it.

Maytag WASHING MACHINE MVWC200XW - Will not clean our clothing. We have been tolerant of Maytags disregard for the people who have trusted their product and name over many years. No longer will we purchase a new Maytag or Whirlpool product. They say third time is the charm but I can not afford to take the chance. I wish them luck, they will need it.

I purchased a Maytag dishwasher for $500. After several months of it working less days than not working, I contacted the repairman. I paid $350 to replace the control panel. I wish I had just replaced it with a reliable product. 1 year into ownership and the seals on the door are falling off. May I suggest never purchasing a Maytag product?

I purchased a Maytag MDB7749AWW dishwasher in March of 2012. The electronic control on this unit failed in June of 2013 (3 months out of warranty). I have been trying to get a replacement part for over a month; the part is on backorder and unavailable. Whirlpool is unable to tell me when the part will be available. So, I have had no dishwasher for over a month and have no idea when, or if it will be repairable. Additionally this part is $150.00 and another $75.00 to have it changed. So it is going to cost me $225.00 to repair a 15 month old dishwasher that I paid $450.00 for. I have received ZERO support from Whirlpool. They told me today, 7-31-13, that the part is still unavailable and they will notify me in 3-6 business days as to if they can find a part. After seeing all the issues other people have had with this part, Whirlpools total lack of concern or support for the consumer and the cost issue it makes no sense to repair this unit only to see it fail again in a year or so. Basically I have a $450.00 boat anchor. The retailer purchased it from feels bad and is offering me another manufactures machine at a reduced price. Maytag has refused to do anything for me. I will never buy another Whirlpool / Maytag item again and I do intend to add my name to the pending class action suit.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

I purchased a Maytag Washer Bravos Quiet series 300 & a Dryer Bravos Quiet series 400 w/ steam in June 2009 from Lowes. I cant express my dissatisfaction in strong enough language with these products. From the time they were installed there were problems.The Bravos series 300 washer: Quiet? Never. The thing sounds like a huge motor whirring around my laundry room. Several times, a coin got stuck in the motor and created a clanking sound that had to be fixed. Ive never had a washer that allowed coins to enter the motor. I cant close the lid on the washer until the whole unit is dry because of the mold problem. I dont feel the washer really gets clothes clean. When we purchased the unit, the Lowes salesman stressed that we could fit a large bedspread into the oversized tub and get it clean. This didnt turn out to be true. The clothes tangle terribly and the unit is off-balance with any kind of a larger load. Ive been forced to purchase the extended warranty because of the complete & total lack of confidence I have in this awful washer (same goes with the dryer).The Bravos series 400 Dryer: This unit never dries. All the setting that should be used with the sensor never work which causes a huge problem. I start out on a particular setting with a stated time limit say, for instance 45 minutes. 45 minutes later, I look at the dryer and theres 1 hr of time still left to go! The dryer just runs on and on. Ive taken to using only the timed dry and I start out at 1 hr, then check it every 10 minutes or so. This is very hard on the fabrics and has caused the useful life of my clothes to be greatly diminished. Also, the stupid thing will start to beep and I cant figure out why. Using this dryer has increased the electricity costs to us.I cant stress enough to STAY away from these products. I purchased Maytag because of their prior good reputation. That reputation is in tatters now. They should recall this product and replace it with products that actually do what they advertise!

We purchased a Maytag front load washer and matching dryer in 2007. In 2010, the main control board of the washer broke down. We spent $450 to replace it.In 2014, the washer stopped working. The dryer started producing horrid odor when we used it. We replaced both with LG recently. We NEVER buy or recommend Maytag products. Stay away from Maytag. There are many other reliable washers and dryers in the market. This is to help other consumers.

My only issue is that I am short and find it difficult to reach the wet clothes to put them in the dryer. Other than that I am quite happy with the machine. I have had no problems to date. Thank you.

This Maytag is about 7 years old now, at least, and is still running strong. The one thing I do miss, though, is the lint collector basket that used to be on GE washers Ive had in the past. Kleenexes have a sneaky way to getting into the laundry and picking out the remnants is a royal pain! The lint basket on the GE would save me that task.

The washer does not wash the clothes, period. It leaves dirt and soap in the machine along with the unwashed clothes.

1st service call about 2 years after we got it. Put around $200 in it. Now broke down again. Service tech quoted $475.00 to fix it. So it was basically totaled after around 6 years. Nightmare kept getting LD (long drain) code. After hours of research I finally called service. Would not drain so I had to wring out a whole load of laundry and bail out the water by hand. Miserable experience!

This model MGR5875QDW range is very difficult to use. When you press broil for instance, the display says set. There is absolutely no indication of how to set. Therefore, no broil. The same thing happens when you try to use the clean function. It is virtually impossible to use the control panel; it is just too difficult. Therefore, most of the functions are not usable.The kicker though is that the handle comes off. During the extended warranty period, a technician came out and fixed it. The toughest part of this job is to get the oven door back on. I tried for 2 hours everything I could think of. Then, I got an idea to use Maytags live chat. They told me that I would have to call for service and pay for a service call to get the door back on. I told them that their clean cycle is too painful to use, so I am assuming I am not the only one who has removed the door to clean the oven. Pay for a service call every time I want to clean my oven or fix their defective handle design because the handle falls off every 2 years? That is not acceptable.

If I want to line dry something, first I have to pick off all the lint. Even when I use the dryer, I still have to pick off lint and there’s often creases with dirt dried right in. I have to inspect everything that comes out of the washer to see if it is clean before I dry it. This doesn’t save water, as I often have to wash things at least twice. Awful! Also, ridiculous. A wash machine is supposed to get things clean.

I have had my Maytag Bravo for 5 years now. I originally paid 1800.00 for the set. And yes that is without the tax. Well I also got a warranty. Three years after I purchased my set my dryer stopped drying my clothes. I called the warranty company for a repair man and lo and behold my warranty is over. The repairman came and said that my lint was backed up. He stated that it was a good thing that I called when I did because they have been known to catch on fire. I asked him how is this possible? I check my lint screen and clean it after every load. He stated that the lint falls off the screen and just settles at the bottom of the dryer. And sometimes the dryer will get so hot that it will actually set the lint on fire. He fixed it but now it is back to doing the same thing two short years later. Im thinking that Maytag must know about this now and I am wondering why they havent did a recall on these before someone gets hurt or even worse by trying to do laundry.

Maytag Bravo Washer and Dryer XL Series - This the worst washer and dryer I have ever owned by Maytag. I wish I could give them away. The washer does not clean my clothes and the dryer does not dry my clothes. They are absolutely terrible. Do not buy them, you will be sorry.

We loved the YMMV4206 microwave - at first. After the warranty was over, we started having issues where we would put the food in the microwave and try to enter the time, wed get the message to open door and close door. Wed try that and for the next few months it would work. At the 18 month mark, thats all it would do, was tell us to open/close door. We ended up unplugging it and it has been unusable since before Christmas. When I call Maytag and related to the support staff our problem, they were of the attitude that it is out of warranty and we can send someone out to take a look at it - for $130 + HST without even repairing it, that would be to diagnose the problem that we already know, then we would have to wait for them to order the part and come back. Do Not Buy this product.

White clothes come out with some sort of grease stains on them and darks come out with a detergent white scum on them. I have to put them through twice to get the scum off and I have to scrub my whites by hand. So much for your new type washers. If I could find a washer with an agitator and water saver on it, I would buy it in a flash and get rid of this so called newest thing on the market. I have to put a cleaner through it every 2-3 weeks that costs me $10.00 for 3 pucks and having to rewash my clothes does not save water or time. There is a lot to be said for the washers that had water saver on them. First of all, I could open the lid during the wash cycle and add another item. (2) I could use the last of the 2 rinse cycles from my white clothes to start a load of dark clothes, that was truly a water saver and both loads were sparkling clean. Every women that I have discussed these new machines with (both front loaders and top loaders) say that you and other companies that think you have improved wash day for women have definitely not improved it but rather made it a nightmare. Absolutely hate this product. I hasnt given me a moments satisfaction since we spent the $1,000.00.

Ive had a Maytag washer and dryer for 10 years. They have worked well, havent had any problems. I bought Maytag because of their excellent reliability, which has proven true. Design is not as modern as others, and doesnt have all the features, but overall solid reliable washer.

Bought new in 2006. From the beginning it shook a little. I could not use high speed without leaning against it and pulling upward on the unit. Maytag service workers came out and at first said they needed to balance it. That was not it. Then they said it was the drawers that I purchased as an option. Finally, one guy just straight up said they had no answer for it. Then came the day, last month, it was spinning and suddenly it started to rock and I ducked out because I thought the tub was coming through. I seen smoke. Yelled for the kids to get outside. With the phone in one hand calling the fire dept, I ran for the electric box & started throwing switches. Fire dept said that is what saved my house. Now it sits in my dining area because of a lawsuit I was never contacted about. No parts are available. Thats what happened when Maytag chose to send the business to China. Now they are back to making them in the USA but why would I buy again from a company that does not make good? Well I love blogging and Facebooking. I know 40% of Central FL because Ive lived here 60 years, plus my husband serve all of Orange County 35 years. This review will go out all over. Anyone need a tall table?

Maytag MHWE450 washer - Purchased this front load washer/Dryer and pedestals 12-1-2011. The bearings are so loud when it spins that you cant hear anything. You have to replace the whole tub to fix it with no directions anywhere on how to do it. I had a Maytag top load washer for 15 years before this. They worked perfectly when I sold them. I thought these would be a great purchase for a lot longer than 2 years.

Same thing as everyone else. The motherboard/control board, the main face of the washer went out and this part isnt covered on an $800 commercial washer after only 3 years of residential use on a commercial washer. Menards refused to swap it out, saying this is Maytags issue. Maytag boasts their 10 year warranty and labels it right on the motherboard as a 10 year warranty, but the motherboard isnt covered? If the main computer isnt covered, What is covered? Just screws? I called Menards and got nowhere. Called Maytag and held for an hour then had to hang up so I can work. The warranty is extremely misleading and is the reason we bought this particular washer, because it says 10 year parts warranty right there, but Maytag conveniently doesnt consider the main control board a part.

Weve had 2 Maytag washers that lasted a combined 41 years. Five years ago we purchased a Bravos XL top load washing machine directly from Whirlpool. Like many other reviews, it is impossible to keep the machine from going out of balance and trying to tear the laundry room apart. I called Maytag and of course they want to make sure the machine is level in at least 3 dimensional space as well as 2 parallel dimensions per String Theory. As far as the 3 dimensions, I assured them I had already thought of this (as an aside, ever try to find any flat metal on one of these machines? Kind of helps when using a level.)So after more exciting conversation, they offered me a Warranty for $437. While trying to control my laughter, I said I could trash the Bravos and buy a new machine for that price. As far as repairing it, it cost $120 for a repairman to grace my door step plus $35 every 15 minutes plus parts -- again, the decision is to trash it and buy a new machine. In case I was too subtle in my comments, I WILL NEVER BUY A WHIRLPOOL PRODUCT AGAIN. Im too frustrated to tell you about my KitchenAid fridge. As much as I detest it, I am forced to join the buy and trash 5 year club . Sometimes the good old days were really better.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

I thought washers are supposed to last 10 years or something. 3 years and I have to replace it. I dont know who Im more dissatisfied with - Maytag or Direct Appliance where I purchased it. Just thought I would rant and warn others about this brand. The computer died so it doesnt know what cycle its on. Repair guy said its unfixable. ARGH!

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

I Hate this machine. It does an inferior job and I wish I never bought it. Our Bravos XL washer was purchased in spring. It left white residue constantly on my clothes. Even WORSE, the machine wrinkled the permanent press so the clothes had to be ironed before wearing. (I rarely had this with my last washer). I used the machine settings correctly and I called the company and basically...was told, Youre out of luck. I hoped that it would improve but No Way! Dont purchase this machine, dont waste your $$$.

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

I grew up trusting and believing in the name brand Maytag. Unfortunately, I wont anymore. I purchased a Maytag MDB7749AWM1 dishwasher from Lowes thinking that I would not need the extended warranty because well it was a Maytag and they just keep working and working for years to come. Not true anymore. 1.5 years after the purchase the control board has gone out. I come to find that hundreds upon hundreds of people have all experienced the same thing. Shortly after the manufacturer warranty expires, the panel dies. By all accounts it is an issue of POOR engineering and Maytag now being produced by Whirlpool. The replacement part is between $150 and $200. Thats about half the purchase price. It is a racket. Companies like this probably think, well if we build something that is going to last and last we cant make money on that. So lets rig it so our stuff breaks right after the warranty and charge half the price of the unit to fix it so we continue to make money either by people buying the part or just going and getting a new dishwasher. Well I can tell you I will be getting a new dishwasher and it certainly wont be a Maytag OR a Whirlpool.

I spent over $600 dollars on a Maytag Bravo 300 series. The washer has cost me over $300 to fix the latch and 2 months later, it will not spin. I would recommend to anyone not to buy a Maytag product! Garbage! I had a standard Kenmore washer that lasted over 10 years without a problem, paid $300 and still sold it for $100. The funny part is that I sold it to my brother who still uses it regularly and has not had any problems. So what is money worth? Your call.

The dishwasher doesnt clean and the dishes and silverware come out greasy. What a piece of crap.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

My Maytag refrigerator (bottom freezer) is about four years old now. Since the first year, it has been freezing up. The refrigerator gets warm and the freezer stays cold. Two repairmen have looked at it, replaced the electric panel and the thermostat - neither repair fixed the problem. If you completely defrost it, it will start working again. For about three years, it would work for a few months, but now it will only run for about two weeks before freezing up again. I called Maytag when this first started happening and again recently. They say they have never heard of anyone having this problem and they are sorry. The woman said she would put my complaint in my file. I certainly would recommend that people avoid Maytag refrigerators.

This machine was in best machines of 2019/2020. It has many features. Ive had one day and have multiple concerns, I will be returning the machine. The dryer isnt great either. Had multiple loads not dry. On the washer, there is no interior light so you cant actually see items in washer to judge soap etc. Has a soap disp that is supposed to hold multiple loads, says 8. Ive washed over 8 and the out of soap alert hasnt come on as youd expect, but when I check the dispenser is full of water so who knows! Cant see inside so I have so way of knowing if there is soap that is still going in, should I add more or what? The alert bell is too quiet, cant hear outside of the laundry room. Multiple loads have not spun out well, leaving standing water and clothes too wet for dryer. Ive had to run a drain/spin cycle to get clothes spun out. It is supposed to connect to wifi but that hasnt been successful, plus, not everyone keeps a phone on them 24/4! Need a louder alert. I washed a sm item that threw it off balance. My LG washed a small floor mat with no issues. I do a significant amt of research before a LG purchase and I feel I was lead astray. I am not happy with this washer or dryer. I wanted to buy American made but this is not up to the standard I expected from Maytag.

I purchased this washer because it has a large, stainless steel drum, and a deep wash setting. My laundry comes out very clean, and I do not need to run it through an extra rinse cycle. The sensor determines what size load I put in, so I am not wasting water on small loads. Overall, I am very happy with my washer. I purchased it about six months ago.

We purchased a Maytag washer model MVWC400XWO almost 2 years ago and it has problems with the bearings and the whole computer board is defective. I was told to buy the extended warranty for $350, which we did. As of today, we were told by extended warranty they are refunding our money because there are so many things wrong with this washer, including the whole computer board, that it would cost them too much to fix or replace it. Im in complete shock. We paid well over $500 and are still making payments on it. I spent the day reading hundreds of reviews from people with these exact same problems and Maytag is aware of it and will not help. They should not be selling these anymore. Im completely sick to my stomach. I cant afford another washer and when I called Maytag, they said it was past the year and we are out of luck. I cant believe this can happen to people and they get away with it. A washer should last longer than 2 yrs.There are hundreds of people going through this with Maytag and no one will help.

Just bought a washer and my clothes are always left with dust and dirt on them after washing. Called Maytag, they sent a technician over, but he found nothing wrong. Company refuses to do anything about it, including exchanging it for a different model, since weve had it for more than a month. I am extremely dissatisfied since I just lost over a grand on a washer that doesnt actually wash my clothes.

Our Maytag Elite Series dryer is not under warranty but we have had nothing but issues with this dryer since we have had it. However, now I have holes in the heat intake at the back of the drum. This is so very dangerous and could cause a fire. I am certain this is a manufacturing flaw. How on earth does the inside of a dryer have parts that will not hold up to heat? At any rate, I want it fixed. The only way to fix it is to replace the drum. This has to be a flaw in design or manufacturing and this particular model should be recalled.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

It doesnt agitate enough to move clothes around. Doesnt put enough water in tub, even on deep fill just barely gets to the top of clothes. Washed a shirt 3 times by myself to get dried mud off of it. 3 time it was washed bumy its self. Clothes do not to get as clean as they did in the old style washers that had good agitation and the agitator that was bigger than whats in these new ones. And water. Need water. We arent trying to dry clean. And even thats done with a liquid that totally covers clothes and moves around better than this garbage I have right now... Looking for an old washer to replace this one... HATE HATE HATE THIS WASHER.

Within 1 month Maytag sent 2 repairmen to repair my microwave. I paid $271.20 for the repair and part. The same 2 parts used the first 2 times were ordered again and I was told that Maytag could not get them again. The service and parts are supposed to be guaranteed for 3 months. Maytag refuses to refund me; offering me 15% off a new purchase. I would not buy from Maytag. They lost a customer.

We trusted the Maytag name to give us a good product that would last. After six weeks the Maytag Bravo stopped working. Having to wait 7 days before a service repair person came to our home. The main motherboard needs replaced. So currently, we are still waiting for the part to arrive and have it installed. 2 weeks without a washer after spending 600.00 for a new washer. There is more problems also, this machine takes 1 hour to complete a single load of laundry. Plus it does not get the clothes clean and the rinse cycle does not get all the soap out of the clothes. Very unhappy with the Maytag Commercial Bravo. Will not buy another Maytag product. Save your money and get another brand. We plan to get this one fix and sell it.

Purchased my Bravos June 2012. This is a horrible washer. It does not clean. It leaves a detergent scum line on clothing. My work clothes are visibly soiled and sometimes come out in a tangled mess. Maytag ignored a first complaint from my wife. I complained again today. Regardless what Maytag does, I will purchase another brand after research. We bought on Maytag’s reputation.

I purchased the Maytag dishwasher a little over two years ago (MDB6759AWQ0). This was the first Maytag product I bought and it is definitely the last one! It was more expensive, but because of Maytags commercials on what good products they had, I thought it would last longer and work better. Boy, was I wrong. When it was installed, it was loud. I brought this to the attention of Maytag. I was told there was nothing that they could do. Repair people were sent to my home several times to see if the noise could be fixed and unfortunately, it could not. This is the loudest dishwasher that I have ever had. I should have stayed with the same brand that was over 10 years old that died! Now the control panel blew out and will cost over $300 to have it fixed. After reviewing the numerous complaints that you have on your dishwasher with the control panels not working, I would think Maytag would be more financially responsible in helping the people that have your products that no longer work after being less than three years old. Just a heads up, Maytag, I will be replacing instead of fixing and not with another Maytag product!

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

I purchased this refrigerator 1 1/2 yrs. ago. The refrigerator stopped getting cold about 3 months after warranty expired. I called Maytag company and told them how disappointed with their product and also how angry I was after spending $1500 only 18 months ago and now it is useless! They kept asking me if I bought the extended warranty and I said I didnt think I would have to after buying a brand new product. And then it breaks so soon!! And now they want me to spend an additional $359 to get the warranty... what a racket! She told me to look under the fridge for leaks. Sorry I cant, Im disabled. She said too bad and would have service man call me but that would be even more expensive. Woops, disconnected.

We purchased our French Door, bottom freezer in April 2010 after a renovation. We have loved it besides needing more refrigerated space. This past weekend I noticed the appliance was cutting off and a few seconds later coming back on. It has an outside ice and water dispenser as well and the lights will blink on and off of course when the fridge cut off. Called for a repair and when the repairman called in the parts he was told he needed 2 computer boards. One was available however the other was discontinued and they would not allow him to just replace the one board. The fridge cost us $1798.00 from Home Depot. I cant believe how irresponsible Maytag is in this case. I have a kitchen full of MAYTAG appliances and have loved them all. But this is unacceptable. The Maytag fridge I had before was 16 years old. I gave it to a family member when we bought this one and that one just broke down last year so it was 21 years old! Whats up MAYTAG?

My husband purchased the Bravos XL washing machine less than a year ago at Bensons Maytag in Peoria, Illinois. Within months of purchase we noticed our clothing coming out with stains they didnt have prior to washing. After hundreds of $$s of clothing ruined we realized it was due to the fabric softener dispenser. We cleaned the machine multiple times & ceased using fabric softener. No luck.Today I finally had enough & called Bensons service department. The fellow I spoke with told me, You are not supposed to use fabric softener with the Bravos XL. I asked why a $1000 washing machine would have a dispenser you were supposed to use. He told me it was because people like to use it BUT you werent supposed to use it. I asked, Why would there be a dispenser if you werent supposed to use it. He told me the salesperson should have explained it during the transaction or I should have read the owners manual more thoroughly. I asked how I needed to go about correcting the problem & he told me to clean out the machine with really, really hot water. I explained we had multiple times.He didnt have any other suggestions so I asked about setting up a service call & requested he access my information so we could verify the warranty. He confirmed the unit was under warranty. I asked to schedule service & was told there would be a $50 service call fee. I told him, I would figure that would be under warranty to which he explained it would only be under warranty if it was the machine ruining my clothes. I asked, What other reason would there be for my ruined clothes and he told me if the laundry was being ruined because I used fabric softener it would not be under warranty. So I repeated that saying So you are telling me if the machine is ruining my clothing because I used fabric softener it will not be under warranty? and he got flustered and basically said he didnt exactly say that and they couldnt confirm anything until a tech took a look at the machine. I told him I would have to speak to my husband.So this is my question... why on Earth do we have a company building $1000 washing machines WITH A FABRIC SOFTENER DISPENSER if you are not supposed to use it? I have never, ever, EVER had a washing machine do such a lousy job. I have never, ever, EVER been afraid to put clothing in a washing machine... not even in a cheap, crappy laundromat. Shame on you, Maytag!

After one year of service from our Maytag Jetclean Plus Dishwasher with Toughscrub the circuit board went out. I have been seeing and hearing other people complaining about this problem. We purchased this device based in large part on Maytags reputation for reliability. I am not happy with this machine. I will complain to the company and write another review based on the results. I suggest Maytag goes back to the old knobs until they can assemble and protect the circuit board, which I believe was damaged by heat and moisture.

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

Do not buy one. Maytag is unresponsive to repairs or parts that are needed. They are not even manufacturing the part that breaks. If you are lucky, you will find out there is someone who will fix the defective computer board... But Maytag will not tell you. We were without fridge for 4 months... They did not care.

We purchased a Maytag refrigerator (freezer on the bottom) in August 2012. In 2014 we had to have the freezer repaired (defrost drain) which cost $153. This month, July 2015, we had to have the refrigerator repaired for another $293. The problem with the refrigerator the repairman told us is the control board (p/n W10503278). He stated that they didnt make the first board very well and hes been replacing this part quite frequently for customers. I only spent $799 on the refrigerator and I already have $446 into it. That is half of what I paid for it! I wouldnt recommend Maytag to anybody!

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

My stove is approximately nine years old. During the past year both my husband and I enjoy cooking from recipes 3-4 times a week thus the stove has become essential. Functionality and size is important when trying to cook meals with two or three components. One of the oven racks was missing from the oven when we moved into the house. Even though it is self cleaning, spills pile up between cleanings so it is great that it has a really cool steam cleaning option. Just wish it were 5-6 years newer.

Wish I would have read the many, many, many reviews on the Maytag MDB8959SBS dishwasher before buying it. As noted by others, the touch control buttons stopped working 1 month after the 1 year warranty expired and Maytag wont do anything about it. BE WARY OF THE 10 YEAR WARRANTY CLAIM - IT DOESNT COVER THIS PROBLEM. Maytag should issue a recall on this product and do the right thing - take care of customers like they used to.

I purchased a Maytag over the range microwave a couple of years ago when I had my kitchen remodeled. I have had it repaired twice already. Each time, it cost over $150. I bought this product with confidence that it was a quality product. To say the least, I am very disappointed and I will never buy this brand again. My previous microwave lasted over 15 years without a single problem. The only reason that I got rid of it was to have matching appliances. It was not a Maytag. I am looking to buy a new microwave and I will be sure to look at the reviews to prevent being suckered again!

Maytag Glass top model #MER8600DHO. I bought it because it got good consumer reviews. This is supposed to be a self clean oven but the steam system in this model is not very effective. It doesnt clean the oven. Would never buy a range again with this oven cleaning system. I wanted to try a glass top stove but wish I hadnt. It is harder to clean and the glass scratches. I really dont like the self clean oven system in this stove - it flat out doesnt work and it takes a lot of elbow grease to clean the oven. The oven however seems true to temperature and does a good job. Overall I am Ok with this stove but wouldnt purchase a glass top again.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

I bought the Centennial top load washer and the dryer in May 2016 at Lowes. They are junk. I had a secondhand Craigslist Maytag washer that lasted 7 yrs and it was still running just fine when I got rid of it after purchasing this HE junk. The flimsy plastic door handle on the dryer fell off about 6 months ago. The clerk at Lowes assured me that the washer was high capacity & could handle heavy loads. Now I cant wash heavy loads because the agitator is already loose and getting ready to break. I have to wash smaller loads on the hand wash cycle. I cant wash my comforter or my rugs. The real kicker is I cant reach Maytag! I have tried calling to sit on hold for 30 mins to an hour. I tried the live chat during their regular business hours and it was not open. I am so disappointed in these machines. This is the first time I have ever purchased a new washer and dryer and this is what I get. I might as well have set $850 on fire. DO NOT BUY NEW MAYTAG MACHINES. THEY ARE JUNK.

We bought a Maytag Bravos XL MCT Washer from Lowes in Oct of 2016. We had cycle issues with it in Sept of 2018 and called the Appliance Repair Service. IT was determined that the Electronic Control board and UIC was bad and needed to be replaced. Estimated cost - +$700.00. We bought Maytag because we thought it was dependable. Not so. Less than two years of use and repairs are more than we paid for machine ($639.00). Receipt would not upload.

I bought Maytag washer 15 months ago and the washer is now leaking from the bottom. My floor was damaged from the leakages. I have not use the washer much in the past 14 month because its just me in the household. I will never buy a Maytag product.

I would like to say that I purchased the Neptune washer & dryer for my parents back in 1998. Up to now, 23 May 2015, not once has either of the machines required service and have been functioning well for the past 17 years. This is a testament to the quality and workmanship that is Maytag. This week I have purchased the Maytag Maxima front loading washer & dryer for my home because of Maytags reputation.

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

While washing clothes in my Maytag front load washer, I noticed that there was water leaking from the front left corner from the bottom. I have owned the washer for only 2 years, and Maytag manufacturer (Whirlpool) told me that it was going to initially cost $80.00 for a service call and then more money to fix the leak. WOW. Also the wood floors that are underneath the washer and dryer, is starting to warp from the leaking washer. I would recommend DO NOT BUY A MAYTAG APPLIANCE. The warranty is basically worthless along with the washer.

Have 2 fridges (one regular and the other is a side-by-side, both were bought in 2006 at Future Shop. The small one is not freezing and the side-by-side ($2,200) is busted too (compressor wont start....). How can Maytag say that their product are reliable on TV??? A Fridges compressor should last at least 15 years !! Maytag, you should at least have the decency to pay for the compressor!

Im told even though my fridge is leaking water and making sizzling sound nothing can be done and my model number and serial number match the recall for this product and I was told that if my fridge catches fire then, Call us but to me thats ridiculous.

Our Maytag oven (not sure model) in the first year started doing crazy things with the oven computer. The oven would shut off and come back on and the display would be garbled. Also when my girlfriend tried to pull the turkey out, the rack fell off the left side and dumped all the juices into the oven. She almost got burned and there was a lot of smoke. The freakin rack should never fall off! Also our dishwasher is on its second control board. I lived by Mr. Maytag and his airplanes/helicopters at Crest airpark in Covington, WA. I wish I still did. Id like to ask him what he thinks of his crappy products. You get nothing for your money anymore. Im not sure but Ill bet both of my problems with these products have something to do with saving a buck by making this crap in Mexico or some other *** hole. Im just glad Maytag doesnt make airplanes or medical equipment.

Purchased a new Maytag washer and dryer in November 2015 after having a old set not Maytag for 25 years with no repairs. WOW. Then the new washer went out in Feb. 2016, now the dryer in May 2016. Very unhappy. Is it because the machines are now made in Mexico? Cheap labor and cheap parts. ICK!!! Thank god for the extended warranty.

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

Bought Maytag dryer in December 2016. Worked fine for first 3 months. Then blue coloring showed up on back of drum and came off on white clothing. Had tech come out. He took pics and send to Maytag. They said it was normal. Further talks with customer service brought statements that we caused problem by drying blue jeans. Funny we never had. They just continued to say this discoloration was normal and we did something to cause problem and nothing they could do. But at least they were sorry for our problem. Whirlpool does not stand behind products. Dont buy.

I related my problems with a Maytag Bravos Washer a few days ago. A year and a half after I purchased the washer, it would no longer spin, among other problems. I was persuaded to call a repairman who diagnosed faulty electronic components which would cost me nearly $400 to repair. He confirmed that the washer was poorly built and strongly advised that I replace it. So, after paying him only $25 for a service call (he felt sorry for me), I did some research and bought a top-load agitator washer because the old-fashioned machines actually do their job - they wash clothes! I was duped by the high-efficiency claims, low-water-usage of the Maytag which didnt wash that well when it did work.

My complaint sounds just like the others listed here. Purchased Maytag dishwasher MDBH979SAB1 at Home Depot 2/2013. In June 2014, the control panel started to malfunction. When I called Maytag, these were the options given: 1--have it serviced out of warranty at $89-$150 for repairmans trip & diagnostic, which doesnt include parts & labor or 2--obtain something called Repair plus one, which covers the cost of repair and reinstates the warranty for one year at the low cost of $264.95. So either way, Im going to have to pay almost 1/2 of the original purchase price. Ridiculous! We had our previous dishwasher (not a Maytag) for over 13 years, with only minor repairs. We purchased a Maytag because we thought it was a reputable company that stands behind their products---well dont believe it! I would NEVER recommend any of their products.

Why is no one doing anything about the crappy product that Maytag is putting out. I am a single mom of 4 and I had to purchase a new refrigerator about 3 years ago. Spent a lot of money on this Maytag, approx. $1400 and it is now useless. I had nothing but issues with it from the time I got it. The bottom freezer kept icing up and then leaking all over my kitchen floor. I had to call a repair guy out, who charged arm and a leg and said it was fixed and 3 months later it was doing the same thing. Since I could not afford to pay ridiculous amount of money to repair it again (although I question what they said they fixed), I had to chop up the ice each month and take huge pieces outside and i had to keep towels always at the bottom of my fridge (yes very attractive) but it ruined my floor and carpet. Now all of a sudden the piece of junk just shut off and stopped working and keeps making this popping noise. Lights went out in front panel. So I had to call a service guy out again but this time I called an independent local guy that is not gonna rape you in charges like Maytag does and he told me to look into this that he has heard so many complaints that the front board with control button has been known to blow out the back circuit board, which is what happened. He told me that parts are MDs, so he would have to get another manufacturer and he heard that even with replacing both of them, it has been known to not work and Maytag takes NO responsibility at all for any of this. THIS IS WRONG. I cant afford to spend around $800 to now fix this or another $1,400 to buy a new one. So I am without a refrigerator. What a nightmare. MAYTAG, TAKE RESPONSIBILITY FOR YOUR CRAPPY PRODUCT. We are hard working people that spend our money and expect a good product. I also have an oven I bought and I can tell you it is a piece of crap too. I swear at it all of the time, as it takes forever to cook anything and the outside that is supposed to be stainless steel is all yoked up. It is like a tin can, looks horrible. I will never ever buy another Maytag product and I hope that ConsumerAffairs steps in and does something about this.

Just purchased a maytag dishwasher from home depot. I did the install myself. The dishwasher will not work at all the panel lights up, but no water goes into the washer. I now must wait two days for repair. After reading all the other reviews, I am thinking about returning it for another brand. And yes the water supply is on. I have hooked up several dishwashers. This is the first time a brand new one did not work right from the store.

I had six service calls, one was a few months after purchase when under warranty for loud noise. I bought it in 08 and since then during the last 6 months, its freezing in the refrigerator. Service person is upset. I contacted corporate and they do not care and told me I should have bought their warranty. Yes, they had to be here when it was under warranty. Still freezing, they played with air hoses, replaced the temp panel and did everything they can, with no results. Theyre giving it one more try and it is going to be hooked up to the Silverado and put on I-75 with a sign on it. Do not buy from this company. Terrible service. I emailed CEO and no response. I just tossed a tomato and strawberry on the tile floor. Yes, buy American. They moved their plant from Indiana (union) to I think TN for non-union. Well, get what you pay for and the employees get what they are paid for. I work in the building business and everyone knows not to buy this product! Just throwing your money away. One good thing is if you like frozen beverages, this is the product to buy! Never again! Receipts in hand! Romney probably owns the stock! LOL

Maytag Centurian is a terrible product. I dont think the designers of this model have ever washed and dried a load of clothes. Washer problems: The lid (top loading) locks so user unable to determine if the correct amount of detergent is being used. There is an unlock button, but it takes quite a long time to unlock (maybe 15 seconds), then an even longer time (seems like a minute or 2 to restart). The machine is LOUD and at one point in the cycle BANGS. I actually returned the first as defective, but when the 2nd machine made the same noise, I was told, no, thats the way it is. It seems to take much longer to wash a load than my previous machine. The Power Wash tears my clothes. Even the regular wash puts holes in my thin tee shirts after a few washes. Really had to get spots out. I almost have to hand wash to get the spots out BEFORE putting in the machine. Dryer Problems: Takes 70 minutes or more to dry a normal load with a couple of towels. The cover to the lint catcher doesnt seem to be properly sealed. Lint particles get all over the top of my dryer. I bought this Washer/Dryer combo last year. Im annoyed every time I do laundry.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

This washing machine is garbage! We paid almost 1000$ for it and it damaged most of our clothes. We believe this washer was released from Maytag with a functional problem. Because it does not drain the water and soap properly, therefore it leaves white stains on the clothes after it is done. Please see in the picture. After recommendation from Lowes we clean washed with Affresh for many times, it did not fix the issue! We called Maytag customer warranty service. They sent a technician and his solution did not solve our problem. We called them again and they said if they send a technician again they might charge us 130$. We think Maytag warranty is a waste of time and energy. They are useless. We will never ever buy anything from Maytag.

Maytag Dishwasher model MDBH989AWB3. The dishwasher was purchased at Home Depot March 19, 2010 in Hollywood, FL; delivered to our new home April 16, 2010 in Brunswick, ME. My complaint is the exact same complaint as the previous 28 complaints! I think the reason our unit worked for 6 yrs is because it was in use only 6 months a year. My experience: you make your selection, two lights come on, you press start, but nothing happens. You think this is a simple repair. You read the manual and try their troubleshooting advice, but to no avail. When you contact the company, they tell you that this is going to be an expensive repair, probably over $500. You contact Home Depot who want nothing to do with you or your dead dishwasher. Their advice: contact the Maytag company. You contact local appliance repairmen and they will repair it at a cost of over $500. You offer the unit to the repairman for free; he declines. He suggests you check the online Consumer Affairs site. It is on that site that you realize the dead dishwasher belongs where one brings other dead things: the dump. I will NEVER buy another Maytag product. I would suggest no one else does either, unless you want to practice your skills in dealing with frustration or you want to throw $693.40 to the wind and watch it flit away helplessly. Thank you for reading this.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

Maytag bottom freezer / refrigerator: What a low-quality operation these guys are operating. We have a 5-year-old double door unit, which is not a cheap ticket item; and we thought that Maytag was from the days of old. The compressor failed along with ice makers and some high-use parts inside. I can understand the plastic lids and guides wearing out with heavy use, but not the compressor. I called Maytag and was directed to their proud Tennessee Service Location. It might as well be in China, where the real owners are located. She said, Oh well, we build quality units that are to last 12 years. However, they are man-made, and you cant count on that being a positive thing. What arrogance. I might get stuck with another brand from Asia. But it will never be a Maytag or any other in their family of products. The repairman is really busy these days.

The stove functions are excellent and the temperature of the burners and oven causes the food to cook even. However after about 6 months the heat from the burners causes the coating on the stovetop to burn like its baking and it cant be cleaned. Now the coating around the burners is horrible and burnt.

July 2018 I bought a new Maytag electric washer and dryer. After one mo. the enamel inside the dryer started come off in sheets. It was replaced with 2019 model which after 3 mos. wont come on unless you unplug it and plug it back in after using it. I am now waiting for Maytag to send a repairman to come look at it. Steer clear of Maytag front load electric dryers.

Our home has seven Maytag appliances: an upstairs kitchen, downstairs suite and laundry room. All were brand new six years ago and what we thought to be good quality by the price we paid for them. We have lived to regret ever dropping a cent into Maytags business account, as we have had nothing but trouble with them. We dont have small kids or teenagers abusing them. Its just us and a very responsible single adult downstairs. And every time we turn around, one of them is costing us nothing but money and grief. Our first problems began with our upstairs fridge when it was only two years old. At that time, it cost us $400 and since then, it just goes on and on. Last week, our downstairs fridge quit, and today, our upstairs one quit. We have had work done on our range, as well as our washing machine and dishwasher. If you are thinking of buying a Maytag appliance, dont, unless you like to throw away your money. I couldnt believe when I looked up Consumer Reviews on Maytag appliances tonight that I would find only 1 out of 5 stars, and read all the terrible reviews written by angry consumers. Well, add me to the list because I will never buy another appliance from Maytag again, and am beginning to think its time to sell this house to get rid of these stupid, useless, pieces of ** Maytag appliances! Sorry, people, but I cant afford to keep replacing them!

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

My new fridge iced over top to bottom. It started making horrible noise then ice maker stopped working. Called MY repairman. Thats when I found out about all the ice. He told me to thaw out and hed be back. It thawed out and then freezer went out. ALL my freaking meats and frozen food had to be thrown out. Now water keeps Flowing out on my NEW tile! Called my repairman back. He came back then informed me it was junk! He said several other customers having same issue. My daughter has the same refrigerator and it broke down just like mine! My repairman also said a big issue with your junk was you used parts from other brands to fix!After reading all these complaints I can see no sense in calling to get it repaired. Its obvious we are all having the same issue. Maybe someone from your ** company could check them out. I dont have the money to buy another fridge! My 85 year old uncle with Alzheimers lives with me and I dont want him to slip on that water and hurt himself! I think all of these complaints need to go to BBB. Thats my next step. I believe you need to recall this junk or give us our money back! I need you to respond or Im going on blast to let everyone know how you treat your customers.