My husband and I purchase both Maytag Washer and Dryer 7 month ago 2017, because we have purchase Maytag washer before and were very happy with it. But this new Washer does not clean clothes at all, it is worthless. We will not purchase another Maytag Washer again.

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

On 8/26/16, we purchased a top-of-the-line Maytag dishwasher from Lowes of Palm Bay, Fl. It began leaking water out one side shortly after installation. Because of a hospitalization, we were not able to report the problem to Lowes until the first part of December. A repairman from Brandts in Sebastian, Fl. came out on 12/6/16 and said it might be the door gasket, but he did not have a new one with him and if it continued, to call back. I called again and another repairman from Brandts came out on 1/3/17. He said it was out of square and he took out 2 screws and said to cut back on detergent because too many suds could cause it to leak (which we find ludicrous). Now it leaks on both sides. This is not a small leak; it soaks the bath towel we put under the door. On 1/11/17 Brandts sent 2 repairmen out and they claimed we needed to cut way back on detergent and put in a capful of salad oil because our water softener is causing the suds which causes the leak. We now use 1/2 teaspoon of detergent and the capful of salad oil. It is still leaking. Our previous Kitchen Aid dishwasher never leaked and we used the recommended amount of detergent in it. We are apparently stuck with a brand-new dishwasher that cannot be fixed. We will NEVER buy another Maytag appliance.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

I’ve had my electric glass top range for four years. Normal use. I set the temperature to 425 degrees to bake a potato. At the 225 degree mark, the oven bursts into flames. The fire burned itself out in about a minute. I turned the oven off and immediately went to google to see happened. I’m pissed! This stove is only four years old!

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

I was so excited to get a washing machine. My excitement quickly faded two washes in when I noticed that the clothes were not completely submerged in water. I checked the handbook and it said that this is normal but at the end of the wash I still had clothes that were completely untouched by the entire washing cycle. The first couple times that the washer was used, I noticed that the water took a very long time to come out. It said it was sensing and then the water would come out in small spurts. When the wash actually started moving, wow the noise was abnormally loud. It continued to make said noise for the entire cycle. I could hear it everywhere in the house. I am so disappointed in Maytag. My father is of a much older generation and he chose this brand based on his past experiences...now I have to tell him its a hunk of junk. Save your money and buy an old fashioned machine.

Bought this Dishwasher two years ago. Control panel was working intermittently now it does not work. I am looking for anyone with this same problem. I know lawyers who are class action specialists who fight for the consumer. We need to make Maytag responsible for the flaws they have in their product. From reading these other reviews it seems that this control panel issue is consistent no matter what model you have. They must all share the same electrical components that is causing this issue with the control panel. My model number is MDB8959SBS2.

I purchased a Maytag Bravos washer in 2009. I have had nothing but problems. Since, it seems that this washer was never tested nor perfected but just put on the market to sell to us, the consumers, the company does not care that this washer breaks down constantly. First the pump had to be replaced, then the tub was replaced. These were nothing compared to coins falling through to get caught in the pump and cause the washer not to drain. When I bought my washer, I also purchased an extended warranty not knowing that if the washer were to breakdown to many times, Maytag would refuse to repair under the service plan that I purchased because now they are telling me that by letting the coins fall through is abuse of the washer. Really so what they are saying is accidents will not be covered, I thought thats why we purchase insurance.Thank You, Maytag. I will never buy your product again.

Internet stated refrigerators should last a minimum of 13 yrs and up. Mine is less than 5 yrs. old, a Maytag 25 cu. ft. French Door Bottom Mount Ref. with freezer on the bottom (MFF2558VEW). Had to replace upper gasket in less than 1 yr. of purchase and needs another now (not affecting the sealing aspect on doors, more aesthetic on upper door thin flap that tears easily).Drain plug & configuration for drain was a known manufacturers defect, but cost me money to replace as 3 yr. extended warranty expired. Lower gasket had to be replaced in yr. 4 of ownership, bottom of freezer was producing a sheet of ice that needed removal every week. Normal settings is #3 for both top and bottom, worked fine for 4 yrs at this setting.Last month irregular cooling started to occur- top down to 52 degrees and bottom freezer below -20 degrees - ice cream hard as rock, have to defrost each time in microwave. Maytag repairman said could find nothing wrong, but try emptying entire contents and unplug for 24 hrs. I could hear pieces of ice melting and dropping throughout the evening. Next morning towels I had put around frig were saturated with water. Restarted frig after 24 hrs. and was working fine for 5 wks.This week same exact problem returned so I did the same thing only this time I had to go out and buy a small chest freezer as I had a full one in my Maytag and no place to put frozen food. It is nearing 24 hrs. and no water has appeared on the floor nor did I hear any ice melting and dropping - so dont know what to do. Will call repair man again and see what he suggests. As soon as I can afford another $1400 frig (this was on sale for $1,002 after discounts, but I will buy a less expensive one this time) I will purchase another brand with NO French doors and no bottom freezer. I loved my frig the first 3 yrs. under warranty, but now causing me too much physical problems having to empty and restock frig for repairs. I have a Tappan Frigidaire in the garage that is from 1998 - I bought from a neighbor who was moving and it has been working fine for 16 yrs. with no repairs. They dont make them like they used to!

Purchased a non agitator washer 1 year ago. Constant frustration with the sensing technology. Cannot select a water level or load size. The expectation is that the machine will do that automatically. The water dispenses through the soap container adding soap to dry clothes which then leave white marks on dark clothes. All of the selections for loads do not have a water level close to covering the clothes. The only way to achieve coverage is to reopen the lid multiple times to restart the sensing feature. Another option is to add wet clothes to increase the weight to “fool” the sensor. Some clothes have come out of the wash still dry in areas. Every load, no matter what size takes a full hour to complete! There is no quick load to be done! I have paused the cycle to leave the house and the water drains from the machine causing you to begin your 1 hour cycle again. Epic fail by the Engineers to provide a user friendly machine. This one, as time goes on, just becomes more frustrating and yes very noisy during the spin cycle.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

I bought a complete kitchen: stove, fridge, dishwasher microwave. Suppose to be stainless steel. All have rusted out within 6 months. Maytag does not stand behind their products. They sent me cleaners and all my appliances rusted more using their cleaners.

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

Bought top of the line Maytag Commercial Technology washer because it was supposed to be the most advanced on the market. My experience has taught me that advanced does not equate to efficient, effective, and expedient. The washer settings for an average load (sheets or towels or clothing) is about 111 minutes per load (nearly 2 hours!!). To adjust to what would be a quick wash is about 25-30 minutes BUT the washing part of that is only about 5-7 minutes. I feel like a Pioneer Woman because I must spend most of a day to run four (4) loads of laundry (sheets, towels, dark clothing, white clothing). This is extremely frustrating!! I am sorry I purchased this product.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

The dishwasher is very stylish and looks great in our kitchen. I do wish there was a small knife drawer in top. It cleans very well and is super quiet. I would highly recommend this dishwasher, good value.

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

So this washer, Bravos MCT cleans good not great. Saves water but clothes dont always come out clean or smell fresh. We have had it for just over a year and the control panel stopped working. Warranty is good for only 1 yr. UGHH!! It is all one unit so the complete circuit board had to be replaced. Half the cost of this washer new! I saved money by replacing it myself. Took 15 minutes. Very easy. Disappointing when you see this is a come problem with this model.

We purchased our Maytag 4000 series electric dryer in October 2011 from Best Buy. We did get a very good deal and have had little problems until this am. I moved laundry into the dryer and started it. While I was loading the washer, suddenly I heard a popping sound from the dryer and smelled smoke. Scared me looking into it. Sounds like either our electrical cord or our heating element blew. Coming from an era (born in the 1970s) where appliances should last at least 20 years, I am disappointed with Maytag. I shouldnt have problems at least until this thing is 10 years old. And even then I have higher expectations. So when I replace this, it will be with a better product.

I purchased the Maytag Bravos series washer and dryer recently. I love the dryer but the washer does not clean the clothes. I have to wash twice if I want it clean. It does not get the stains out and does not use enough water to rinse the clothes. It also does not use enough water to wash/clean the clothes. I ended up washing all the loads on bulky which fills the washer with water. It still doesnt agitate enough to get things clean. I am extremely disappointed in the Maytag product which I always thought was top of the line.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

We purchased a Maytag dishwasher (model mdb4709aww1) from our local appliance store. A little over one year after purchase, the control panel (part w10254834) stopped working. Our appliance store replaced it. They charged us for the part but not for a service call. Its been two years since the new control panel was replaced and it just stopped working. Now, we have to pay $275.00 for the new part and service call. My previous dishwasher lasted twenty years and we never had a problem. I thought Maytag was a quality product. Sadly mistaken!!

This top load machine replaced a top of the line Maytag Neptune. It has five water levels. It has three temperature settings and four wash selections. It also has a selection for an extra rinse that I use for white loads. The washer is very reliable. Clothes come out clean with an average amount of detergent. Although this washer is more than fourteen years old, it has never needed service or repairs. By running a cleaning cycle every six months, it drains like brand new. The stainless steel drum is still as polished as it was when it was new. Even the hoses have lasted with a need for replacement.

I purchased this dishwasher about eight years ago, and I love the performance and the stainless steel interior. I never have a problem getting my dishes clean. This product definitely lives up to its reputation. Going forward, I would definitely buy the same brand if it became necessary.

In December 2017 I bought a Maytag Bravos (w/o agitator) based solely on past experience (56 yrs.) of buying from Maytag without any complaints. A friend told me I wouldnt be happy with my purchase and she was RIGHT! It doesnt get my clothes clean to my satisfaction, my towels are all getting snags as well as silky sheets and pillowcases and dark clothes have a soap scum line on them. I have slightly better luck if I wash everything with the deep water level option but I still need to wash dark clothes a second time without any soap or fabric softener to lighten the scum line.I am very careful to use minimal amounts of high efficiency detergent but that doesnt help. I called Maytag and complained within the first month but then we were gone for the month of February and I just never followed up with them. Now Im sure its too late to do anything. I wish I had listened to my friend. Hopefully I can save another consumer from making the same mistake I made.

I bought this washer (Maytag HE) almost a year ago, and if I could redo my choice, I would not choose this machine. There is no separate spin cycle. Often items are left with quite a bit of water in at the end of the wash cycle (often literally dripping as you transfer to the dryer), and you cant just rearrange them in the washer and then spin again. The only option on the washer is to both rinse and spin, which almost never helps get out more water. So you then have a heavy load in the dryer, much longer dryer time, and higher utility bills to get some loads dry, especially bath towels, sheets, jeans, etc. The washer is large capacity, but if you fill it more than 1/2 to 2/3 full (depending on the heaviness of your items) the spin cycle definitely will not get nearly enough water out of the clothes. The lid on the washer is SLOPED!The most ridiculous design I have ever seen for a washer, everything you set on top, even for a moment - laundry detergent, folded clothes, wet clothes - ends up on the floor. And the lack of agitator means at the end of the cycle, some loads that contain a sheet or any large flat item (tablecloth, etc.) the rest of the items are captured below the larger flat item that is over them like a mushroom cap. You cant tell how long the items have been like that in the washer, but its hard to imagine they are getting properly cleaned and rinsed. You absolutely cannot use powder stain removers, especially OxiClean, unless you are using the oxi cycle (much longer than regular cycle) because with any other cycle you will have white cloudy patches on all your clothes and items where the powder dissolved in the water but did not rinse out. You have to manually scrub them out, as putting these items through another wash cycle does not remove all the spots.

The fridge has a grinding noise that is getting worse, by the day. I cannot seem to define the exact location of problem, whether the freezer or the fridge. Maytag you stink, and your web site stinks, too.

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

I purchased a Maytag Dishwasher #MDB7749SBM1 as part of a complete kitchen remodel less than 3 years ago. Maytag was a great product years ago so I thought I would switch from GE to Maytag thinking that I had purchased a quality set that would give me years of great service! What a bad choice to say the least! This dishwasher has never dried the dishes completely with heated dry option. I never cared for the plastic latch and metal catch option either since I caught water dripping from the bottom since the door must not have been completely shut even though the latch was secure.Most recently, the start option on the flat control panel will not work. After opening and closing door multiple times I can get the start option to light up and run the cycle. Added bonus to start option not working correctly is that when the dishwasher door is shut, it automatically runs hours later with no human interaction. The dishwasher lights were lit up like a Christmas tree at 7 am this morning and running a cycle. Guess it thought the dishes werent clean enough. I am going to price out a board and determine whether I will throw this piece of crap in the dumpster and find a different brand! I HIGHLY RECOMMEND THAT YOU DONT BUY A MAYTAG DISHWASHER!

The unit has an ice maker. On a regular basis, water would accumulate at the bottom of the freezer pan. When the bottom pan got filled up, water would run out on to my hardwood floor. I related the problem to the ice maker. Researching the problem, I learned that the ice maker has an adjustment for timing the on cycle for filling the ice tray. After several adjustments nothing changed. I ordered a water control valve and installed it. The problem persisted. I installed a water pressure regulator but the problem persisted. I installed a water filter, the problem persisted. I turned off the entire ice maker and the problem persisted. The problem wasnt the ice maker. The real problem was the defrost cycle of the evaporator. The drain for the water was plugged with ice. I made modifications to the design so I could monitor the drain hole in the back of the freezer. Will I purchase another Maytag… probably not?

Maytag topwasher 2011 model MVWB300WQ2, SERIAL C11271134 - Im from the old school, expecting to get my money worth. I purchased a Maytag Bravos automatic washer in 2011, now less than 5 years later, it has a very loud knocking noise during the draining and spin cycles.

Washer broke down after one year. The washer stop in the spin cycle. Called many times - got no satisfaction. Still using local laundry mat. Very disappointed. Always thought Maytag was top of the line. I guess I was wrong.

This washer is only two years old and does the wash for 2 people. The control board has broken down and the lid lock did too. Of course the warranty had just expired, so there is no help from the maker, Whirlpool. Save yourself a big loss and dont buy these brands. Mine is going to the dump where it belongs. Thats $500 down the drain. Do yourself a favor and get a Speed Queen.

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

Second time I have purchased a Maytag washer. Both units failed within six months of extended warranty running out. Maytag repairman is sitting on his **, not because they have a quality product but because consumers are seeing that it is a subpar product. Don’t waste your money on them or any of their off brands.

The top loader washer Commercial Technology washes very small loads well. I bought it for the deepwater wash. It DOES NOT work. It also has a auto sensing. Hate this washer. I have to pour buckets of water in the wash to fill it. Maytag/Whirlpool go back to the way it should be. If I want a full washer I should have it! At the end of the day IT IS MY WATER BILL!

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

If you are looking for the Maytag repairman he will be at my house Tues fixing my barely 1 yrs old dishwasher. This is ridiculous to pay this amount of money for the reputation that Maytag is known for or I will say was known for. $270.00 for a control panel. My last Maytag lasted over 30 yrs. Not made in the US - not built to last and this was told to me by the people that installed it so take it for what its worth. Look elsewhere. My last Maytag product.

I purchased the Maytag Bravos MCT HE washer in 2011. Its about 3 1/2 years old and there was a very loud noise when the washer went into the spin cycle. Called the repair man and they told me the bearing and spin basket needed replaced. I had always had Kenmores with very little issues and they lasted for 12 years plus each. I get the HE model from Maytag and cant even go 3 1/2 years without some major issue. I called Maytag (Whirlpool) to complain and they said there wasnt anything they could do. I reminded them that I had checked for recalls on this model and looked into some of the complaints about this washer and that there were many of the same issues that I had plus many others. I felt like there should have been a recall on the bearing since they are going out too soon for this kind of a washer. I guess the Maytag repair man is now busier than ever since I dont see them on any advertisements anymore. Well, I will never buy a Maytag or Whirlpool appliance again after this.

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

Only 2 months after purchasing the Neptune Washer I required a service call as the washer was not draining. Technician replaced the pump and cleaned the drain filter. 4 months later the same issue happened. 3 months later the computer board was replaced and filter cleaned. Since purchasing this washer I have had to have 5 service calls to have it fixed. I called Maytag and they told me it is my fault the filter is clogged. Although the things in the filter are from my familys laundry the filter is located in the middle of the machine which requires the machine to be torn apart to clean the filter. This is a TERRIBLE design flaw which is NOT covered under the maintenance agreement as the service technician said this problem was caused by us. Maytag was the absolute worse to deal with as I have spoken to two levels of customer support managers and all of them said its my fault.

Maytag has always been my choice with appliances. Ive purchased others and always dissatisfied. This dishwasher has been a trooper and lasted forever. Its been overworked with 4+ children and yet still going strong. I recommend Maytag????

A washer should last 10 years. Bought it in 2009 - after two years we spent $200+ on seal and bearings. Now, in 2014 we need more seal and bearings and the service tech recommended by Maytag says the cost will be $500+. Machine has a serious design flaw, and bad parts, and bad service.

Bought a Maytag HD top load washing 11/4/17. Within the first month the machine began to make a loud squealing noise during the wash cycle. A repairman came out 2 times before finally replacing the gearbox and tub. Within the last month or so the problem began again, another repairman came out twice, and once again, had to replace the gearbox and tub. When he left I ran a load and the machine sounded like a war was occurring inside of it. Very loud banging and grinding... heck I was wishing for just the squealing back! Maytag refuses to replace the machine and just keeps sending out repair people. The Maytag name once stood for quality but that was long ago.

Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!

We bought a new Whirlpool dishwasher, and it was a nightmare. So after four years of that we tried their sister company Maytags dishwasher. I have to say that I think these two old American brands have been ruined. This Maytag dishwasher is always making my dishes smell like rotten fish or a dead animal. I have to dump bleach and or vinegar down in the bottom constantly to keep the stink down. And I have looked and there is no food laying in the grinder. Then we started to lose wash cycles, and the buttons (not real buttons but a cheapo control panel) started to malfunction after 2 years. Now, 3 years into it the plastic adjusters in the top rack are broken, control panel has gone totally haywire, and still smells terrible. I remember when American appliances were sturdy and reliable because they were designed by engineers. Now they must be designed by accountants and shareholders. Goodbye Maytag and Whirlpool.

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

Dryers been installed for 3 months, 3 service calls to date. Heat unit failure. 1st service call no show, no call. 2nd service call fixed the problem 50%, the dryer would heat on timed dry but no other modes. A week after that call heat unit failed again on all modes. Awaiting 3rd service call. Customer Service Department at Whirlpool Canada could care less. Avoid this product, Maytag 2000 series dryer - do not buy.

These machines have lots of service problems, although Im not familiar with the newer models. The function and the features are adequate, and typical. And overall, again, I have no complaints other than shortly after purchasing, there was a circuit board recall for these machines, and fortunately, I had a repairman who knew of the issue, and guided me to a cost free fix. Overall, it has served the purpose well of cleaning my clothes in a decent fashion.

I bought a Maytag washer November Thanksgiving of 2013. This washer started giving problems three months after; problems such as the cycle stop turn over properly, the light would say wash but its not washing. It would just stop but the light stuck on wash for long periods of time. Press the pause/start/cancel button, it would sometimes start again and stop and let out the water quickly. The clothes would be filled with water and not wash properly. This the funny part, serious funny part. I contacted Maytag on countless time. They had me on hold so long I had to hang up; a hold for hour I am talking about. One day I finally got through. They gave me a number to contact because where I am located there is no tech. I never got anyone but the machine when I called the number after countless times of trying. I decided to called back Brandsmart, because I just think its not right and fair to me to purchase a washer for so much, to had it shipped for more money. It didnt last me NO time at all and I cannot get any help. Well! Brandsmart told had to have paid export shipping, something I never was offered and since I took it out of the country, there is nothing they can do for me. I hunted for my receipt and to this day I I still have it. All was offered was warranty parts and labor for a month, thirty days. I said no because I would not think anything would go wrong in that short period of time. Nevertheless was not offered any export shipping warranty like what they are trying to ** me with. Here is my receipt number **. I grieve presently how I was just robbed of my money so openly when all I wanted was a replacement.

I give the Bravo T/L Washing machine and the Maytag company zero stars. I had to call for service 3 times within the last 22 months, twice for the electronic panel which needed to be changed, and the third time, it needing a new tub/drive shaft assembly at a cost of $405.27. I did receive a call from the Maytag customer service and all they would do is make a note of my complaint. I feel if you pay almost $1,000.00 for a machine it should work for more than 22 months. I believe Maytag manufactures an inferior product.Not only did it not last, my family and I found that the clothes didnt come out as clean as it should have, and sometimes, the towels would have a mildew smell to them after washing and drying. I assure you that I have read the enclosed instructions of how to use the machine, load the machine, and only used products designed for the machine

This is our 2nd Maytag washing machine in 25 years- we upgraded to a newer model though the old one was still working. The settings on the newer model are perfect for our family and we love all the options. We love our machine. Thanks.

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

I purchased a Maytag Bravo xl washer & dryer for $1600 in May 2017. Sunday, the user interface panel went out in the washer. After an $85 diagnostic visit, we were told it would be $500 to repair and take an additional 5 days. My husband is recovering from major knee surgery so I was short on choices. I elected to purchase a new speed queen and will never purchase Maytag again. The 10 yr warranty tag on the front is useless!

Maytag Centennial HE Washer - Worse machine ever. Takes over an hour for a load of clothes, never clean. Had only for 18 months now, it wont advance past wash cycle.

This has to be the biggest joke in the world for the respected name of Maytag! The engineers that developed this worst-of-all machines on the market must have been circumcised with pinking shears. 80 minutes for a wash cycle? Even rapid wash takes an hour of slowly spinning and spinning ad nauseam with almost no water. The clothes sit in the same position even on the very brief agitation cycle... Nope, the clothes do not come out clean, although if you add bleach to the dispenser, since there is no water in the tank, the bleach does triple duty and rots the clothes. Is this masquerading as energy efficient when all of the cycles are an hour long, about? Unfortunately it takes water to clean clothes and the environ-lack-of-mentalists must have bribed Maytag to develop the worst washer on the planet. Absolutely!

Maytag Washer and Dryer XL Bravos - The worst machines ever. I have had many washers and dryers and every one of them were good enough to get my clothes clean and dry without wrinkles. This washer Maytag Bravos Washer and Dryerdoes not clean clothes no matter which setting it is on. The dryer does not dry the clothes without wrinkles if it dries them at all. They are only about 6 months old, I have followed the book on usage and it still doesnt help. If I could pick these up and put them at the curb I would. If Maytag would take them back I would return them. Buyer beware.Updated on 03/17/2018: Maytag wrote to me and wanted me to give them my contact information along with any other info regarding their appliances. Still havent heard from them, and I assume if I do it will be like all of the other replies, Sorry for your inconvenience yada, yada, yada. I did check online for Lemon laws for appliances and there are laws for the consumers to fight the companies. If and when they contact me I will be sure to mention this to them for what its worth. I think a class action suit might be the answer for all of us consumers. If banding together would help count me in!!!

This washing machine is garbage! We paid almost 1000$ for it and it damaged most of our clothes. We believe this washer was released from Maytag with a functional problem. Because it does not drain the water and soap properly, therefore it leaves white stains on the clothes after it is done. Please see in the picture. After recommendation from Lowes we clean washed with Affresh for many times, it did not fix the issue! We called Maytag customer warranty service. They sent a technician and his solution did not solve our problem. We called them again and they said if they send a technician again they might charge us 130$. We think Maytag warranty is a waste of time and energy. They are useless. We will never ever buy anything from Maytag.

What junk. Bought this gx2shbxvy05 french door fridge. In less than 16 months the freezer is fine the fridge section gets up to 80f. Throw all the food away. Found the freezer coil covered in ice. Took the back panel off and noticed ice around the copper tubes by the compressor going up into the body. Not good. Put a small brick heater in and slowly melted the ice into the drip tray. Warning, it filled up 4 cups of water and of course spilled and killed the wood floor. After the clean up. Plugged the unit in and it seemed to work for about 3 months. Now its dead again. Looked into parts around 300 to 400 bucks plus labor to replace the system needed parts. P.S. the fridge, this junk replaced is downstairs working after 25 years not one issue other than the color. NEVER BUY A MAYTAG product please. TRAIL APPLIANCE should never have sold this product and should have stepped up to help out. Wont buy from them again.

MDB77495852 - I purchased a brand new Maytag dishwasher 2 years ago from Sears. A year later it broke down with what was apparent moisture in the control panel. Thankfully it was covered under warranty. Well guess what... it broke down again a year later and now just missed a year. But not it matters, the retailer (Sears) said it was not covered so Im supposed to pay about $300.00 to get it repaired. And figure I will have to do so next year also. I was told there is a Lemon Law for appliances but it does not kick in for 4 years. So after $900 in repairs I could get a replacement... REALLY? I think a recall is in order!

I purchased a Maytag top-load washer 16 months ago. I had a problem with it four months after purchase and they told me it was not leveled, which I did not believe. I set it up as the manual said to. The washer left clothes soaking wet about every 30 loads. I continued to use it and the washer finally quit working after 16 months. The repairman found the nut which holds the pulley on the shaft that turns the drum had been loose and had been this way for some time. $129.00 later, it was fixed. It works fine now. I wonder if this problem should have been caught on the first service call when it was still under warranty.

We bought the Bravo washer and dryer in 10/2009. Since then the dryer has never worked well. Weve had at least 8 service calls on same and the sensor doesnt work, i.e. says the clothes are dry when they arent and we always have to run them through at least two-timed cycles to make them completely dry. The washer is another nightmare. At least 8 service calls as well, and after one where the motor was replaced, it popped off and flooded my entire house. They laundry room is located on the second floor. I had to replace floors, walls, ceiling, light fixtures, etc. Insurance covered it but it never shouldve happened. Now the washer doesnt drain properly and the error code LD displays every load and we must manually drain it by either setting an extra drain cycle or take the entire machine apart and vacuum out the water. Each load takes twice the amount of time it should, if not more. But I guess its okay because the dryer takes just as long to dry a load of clothes. Something has to be done. Maytag is refusing to stand behind their products and it seems as though many of the complaints are for the same issues. Is there a lemon law for household appliances?

I bought my Maytag washer thinking that I was buying a quality product. My washer hardly ever can complete a spin cycle without bumping and knocking and then stopping. I have to babysit this washer because we never know if it will complete a cycle or not. The machine is totally level. We have to adjust almost every load just to wash clothes. Sorry Maytag but this washer is crap and I will never buy anything made by Maytag. What a waste of my money.

On the 11/25/16 bought a refrigerator at Home Depot. Beside that the first was not called off, wait for another month 12/31/16 for the other refrigerator the problem are. I file a complaint because Maytag left me a message refrigerator half a price. Now they deny when I have proof.

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

I’ve had my dishwasher for over 10 yrs now and I probably need to upgrade but it suits us just fine and I’ve really never had any problem with it at all. My dishes and especially my glasses come out Sparkling.

We bought a new Maytag top load washer March 2018. July of 2021 it starts making the worst racket Ive ever heard. I thought at first that there was a dog being killed by another animal. As I ran to the door I realized it was my washer. Long story short, repair guy said itd be cheaper to just buy a new washer. Maytag did nothing to help us resolve the issue of a 3 yr old machine totally useless. We bought this machine because we thought it would last for years. I mean their commercial shows the repair guys doing nothing because Maytags never need service. My new machine is not a Maytag. No more Maytags for me.

MF12269VEM7 - I purchased a refrigerator in September 2013 and my ice maker stopped working within 1 month of delivery. I had the motor and ice assembly changed 3 times and over 12 service visits within the first 6 months. I had the motor and ice assembly replaced in March 2014 and they offered to extend my warranty for a year. My ice maker has stopped working again. When calling Maytag customer service, I spoke to the Supervisor who will pay for the parts but require me to pay for the service calls. As well they only have a 6-month warranty extension on file. This fridge is obviously a lemon but they will not take any ownership because I did not purchase an extended warranty! The Supervisor state he does not report to anyone and he has the final say regarding my service. I will never buy a Maytag again. A year and a half of ongoing problems and no solution.

I had a problem with my 1 year old oven. I scheduled an appointment and no one showed up. So I fixed it myself. A week later they called to schedule an appointment and I told them that they were scheduled for last week. So their response was OK, I dont need them anymore - goodbye. The parts are under warranty so I send them the part I replaced myself and the invoice for the cost. I didnt get a response. So 3 months later I send a second letter. Three more months and still no response. I can remember when Maytag had commercials showing their repair sleeping because they had no work to do. Now, their products are failing and their entire service depart is asleep.

I purchased a Maytag Bravo Washer in October of 2011, I had a repair man come to check it since the spin cycle sounds like a jet is revving its engines in the laundry room. He told me that the repair cost is $493.50 to replace the transmission. The machine also has problems with the circuit board. The lid lock goes on and off and on and off so you cannot run the machine. Speaking to Maytag they just kept saying your warranty is over and we dont offer any assistance on the repairs. The machine cost $530.00 in 2011 and they think its reasonable to have repairs more than the cost of a new washer. They said they had no complaints on the model. My repairman advised not to buy Bravo, Cabrio or Calypso models since they all have the same problem with the transmission and electronics. I think they should at least pay for the parts, the transmission is $300. And we didnt even price the electronic part of repair.

I purchased all new appliances and decided to go with Maytag. My Maytag Refrigerator model MFI2569VEM after 12 months, just after the warranty expired, started leaking all over my kitchen floor. I called Maytag and all they told me was there is no recall on this model and there was nothing they could tell me over the phone. I purchased an extended warranty and that is a whole other problem to get someone out. They said to check the freezer problem I need to call when the leak was occurring, so they could see what is happening. So basically, I need to leave water on my kitchen floor so they could see what is happening. Who hires these people?

We bought a new Maytag fridge in 2013, french doors, ice maker on the bottom. In 2 years we have replaced the control panel on the front door 3 times. Each time the plastic panel cracks and breaks free. The last time they replaced the entire door, all on warranty. Well 3 months later it does the exact same thing. I call Maytag and they say, fridge is past its warranty period so no coverage. It will cost me about $600 to replace this control panel.

I purchased my Neptune Washer in 2005/2006. I had a mildew problem, and the store told me to clean it with bleach. It is now 6 years later, and the ball bearings are going out. I called two different repair companies, and were told by both they would save me the call out charge, because the ball bearings were going out, and it would cost between $ 600-$700 to fix, so I may as well buy a new one. The washer is only 6 years old. This is completely unacceptable! I then tried to find someone online to fix it, and I ran into the fact that the Neptune Washers had a recall. Why was I, not notified? I bought the washer and dryer set from a Maytag store. No one tried to reach me. I am now stuck with the problem of buying a new one, and really cannot afford one at this time. I went with Maytag due to the brand name, and I knew it would be reliable. Is the joke really on me? Can someone please call me, and point me in the right direction?

We Purchased a Maytag gas oven/stove three years ago believing it to be the quality of the Maytag of yesteryear, Boy have we been disappointed! When Whirlpool Corp. bought out Maytag several years ago they continued using the Maytag name only.. The quality is now less than substandard, It is a cheaply built piece of crap.. We would sell it in a garage sale and replace it with a quality stove/oven but we dont want anyone else to have to deal with this piece of junk! It will soon go to the landfill!!!

I purchased an emerald green washing and dryer (MHW4200BW) by Maytag. Unfortunately, my washing machine broke and I bought the extended warranty. After many visits from the repair company, it was determined that one of the parts needed was on back order indefinitely. Maytag decided that they would replace the washing machine. Sounds like a fair and good deal, however, the washing machine that they are going to replace my unit with is of a different color. Apparently someone in upper management at Maytag made a business decision to stop selling this particular color unit with little to no regards to the customers that had already purchase their product in that color. Had I known that they were going to discontinue the color, then I would have stuck with a standard color like white. At least I would not be faced with having a mismatch unit now because Maytag will not replace both units. To make matters worse, my washing machine and dryer is on the first floor right off my kitchen. It is not stuck in the basement way from company, etc. I am so disappointed in Maytag and their lack of consideration for their customers.

The worst wash machine Ive ever used. It doesnt clean clothes well. It constantly had error codes. Im constantly having to unplug and reset the machine and 4 times out of five it will NOT restart. Not to mention it stinks worse than my sewer. I have to run the refresh cycle every four to eight loads. Ive owned this machine three years. And it has been three years too long. I will go back to a ringer washer or a wash board and have better results.

I have had the washer and dryer for a little over 2 years. The washer already needs to be replaced as the cost to replace the drum is almost as much as a new washing machine by another brand. Thought Maytag was the very best. I had a GE washer for years before I purchased this set. The GE wasnt broken but THOUGHT I was upgrading..NOT!!! Will not purchase Maytag again. Very unhappy!!!

Maytag bottom freezer, 4 years old, ice forms on bottom of freezer. Water melts all over floor every few days. Please add my name to class action suit if/when one comes.

When I remolded my kitchen almost four years ago, I purchased four Maytag appliances. There was a recall on my dishwasher that was successfully fixed; the heating coil could have caused a fire. The next appliance to go was my refrigerator with a bottom freezer: the freezer section went. Thank goodness I purchased a policy which covered the repair that had to be done twice--twice I lost food. I was compensated by the insurance company for $200.00 for the cost of food lost. Just before Christmas my microwave stopped heating. The turntable works, the timer works, but it will not heat the food and makes a loud noise. The glass top on my stove is getting marred even though I clean it every time something spills. I keep my appliances in immaculate condition and they look like new. I thought when I purchased Maytag I was buying reliable appliances. Their ad that states that the Maytag repairman is lonesome because he has no work is a lot of bull. Each appliance has had problems. Where is consumer protection? Appliances should not breakdown after a couple of years. We should not have to buy insurance policies that are expensive to protect appliances that should last at least ten years without problems. Someone needs to step in and help the consumer. I didnt call Maytag regarding the microwave as I was told it was useless to call them and all I would get would be aggravation. Someone, please help the consumer!

Bought a Maytag bottom door refrigerator/freezer about 3 years ago and within 6 months had the bottom drawer ice freeze issue that is so common all over the internet. Today is the THIRD ** time Ive had to take this piece of crap product apart and clear the ice. For all of you who have contacted Maytag in the past... Ill bet you got the same response I did when the fridge was new. They claim there are NO KNOWN ISSUES. They actually told me they had NO RECORD of previous complaints with this issue. MAYTAG SUCKS! I wouldnt take a free appliance from them. Worst customer service possible and they take no responsibility for their ** design and problems. There should be a class action suit for this issue. IF ANYONE IS EVEN CONSIDERING A MAYTAG APPLIANCE... Do yourself a favor and think twice.

When I attempted to contact Maytag about an issue in my 3 month old washer all I received is an automated email back saying to contact one of the repair places on their website. There was one, so I notified Maytag I would contact them. I contacted them. They said Maytag had not notified them that this was a warranty repair and if I wanted them to come out I would have to pay for it. I have attempted to contact Maytag several times to get this straight. Guess they are trying to wait out the warranty to respond. Will NOT EVER buy another Maytag. Too bad they used to be a good product.

Brand new Maytag dishwasher, model #MDB6709AWBO, installed after one year warranty because of extended time needed to complete kitchen. It just never worked. Repairman says control panel faulty. Sears wont help or replace. Sears’ service is extremely poor, over one hour on phone transferred over and over and then told too bad by a Supervisor. After checking this site, I realized Maytag suck. And what to do now that I paid $700++ for fancy dishwasher that doesnt work. By looking at other peoples complaint, it will break down over and over.

We purchased Maytag microwave (MMV4205DH1) less than two years ago. Within the first year, the microwave would not work and we would see an Open and Close Door message. We had it repaired and now 10 months later it is doing the same thing. The cost of repairs is high--the same as a new microwave. We have been inconvenienced throughout the holidays by our broken appliance. Disappointed.

Fire Danger. We had a power outage and my Maytag gas range/double oven (Model: MGR6875ADS) was dead after the power came back on. We figured it was the control board and braced for the expense to replace it. A few days later, I plugged the oven back in just to see if it would work and it did! The control panel came back on and we were up and running. The good news end there. On Christmas Eve, we came home to a house full of smoke with fire alarms buzzing. A butcher block style cutting board that was on top of the range with Santas cookies on it was on fire. Twenty more minutes and the house would have been gone.

April 26, 2011, I purchased a Maytag top and bottom fridge from Home Depot. After a few days, I noticed frost starting to form in my frost-free freezer and the fridge wasnt really that cold. I adjusted the dials thinking that may do the trick. Nothing changed, it was all the same and instead, frost was thicker. I contacted Maytag, which by the way was taken over by Whirlpool. I told them my situation and since I had just bought the fridge, I wanted a new replacement. They told me things didnt work that way, that I had to honor the warranty. Fine, we are almost entering October now. I have had several services calls, I have written to the Better Business Bureau, I have lost a few hundred dollars worth of food for it would be full of ice and had to be thrown out, I have contacted the executive offices of Whirlpool but they, along with the Better Business Bureau are not doing a thing. Tomorrow, once again, I am having a service call and once again, I know the issue will not be fixed. All I wanted was to either get my money back, along with extra for the loss of food or for them to just exchange it for another one, since this one was purchased with a problem. I really dont think that its right that they are able to get away with this. Just looking at this page, I see that there are plenty of people with this same issue. What is being done about it? If it were them with this issue instead of us, you know ** well they would have had a new fridge the following day. Here is my model# M1TXEMMWQ and serial# VS04658359 for this fridge. Please, I would really appreciate some help here.

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

I bought a Maytag dishwasher, model # MDB7749AWW1, in April 2011 and the control panel just stopped working. Of course, Im outside the one-year warranty, but judging from the other reviews on this site, that doesnt really matter. A $500 dishwasher should last more than 17 months! I agree with the other consumers. The control panel on these dishwashers should be recalled. Obviously, its defective. Instead, Im being told I can either pay $250 for the repair plus a one-year warranty or $130 plus parts to cover a onetime fix. Ridiculous.

My husband bought me a Maytag washer as a surprise gift. I was so excited to get a Maytag. I will never purchase a Maytag again. I am so tired of washing, rewashing and rerinsing my clothes and still not getting the soap out. I have used every different kind of detergent and used with and without fabric softener. I have also tried cold, warm and hot water. I would rather use more water and get the soap out instead of using more electricity to keep rewashing my clothes and then in the end having to take a wet cloth to get the soap out. Never had to do this with any other washer I owned. Very disappointed as I always thought Maytag was the best.

I bought a Maytag Bravo washer 11 months ago, and I have had nothing but trouble with it. I have had it worked on twice, and now, Sears is sending me a new one, because it is broken again. I would rather have my money back, go somewhere else, and get a new washer. I will never buy anything from Sears again. They could not send a person out for other repairs for 1 week. Then they would have to send out for parts, because the drum is peeling on the tops. So that means more time to wait for parts to come in, and the machine is not spinning out. The cycles are not washing right; sometimes, they wash a cycle 2 times.Sears does nothing but give you a runaround. And the Morrisville Vt. store manager is so rude. He was talking to me like I was stupid. Now, I have to wait 3 more days before a washer comes in from the warehouse after Sears told me it was coming on 4/24 between 9:45-11:45. Then the manager told me I could take the floor model if I want it today, which has scratches on it. I was hoping someday to buy the dryer to match the washer. But now, I do not want anything to do with the brand. I bought a Maytag refrigerator also last year. Its beautiful. Everything is in my kitchen, and I have been working on getting everything to match. I am raising my 2 grandchildren and am on a fixed income. They treat people awfully at Sears, and it is too bad Maytag works with them.

My name is Luis ** and I own a Laundromat in Yuma, AZ. I recently purchased 10 Maytag top loaders model MVW18PDAWW in August, so the machines are practically new. They are the new HE top loaders with locking lids. Since I purchased them I have had nothing but trouble. Customers have complained about them on a regular basis; there are days when we have had as many as five complaints.First of all, the locking lids proved to be a much bigger problem than we anticipated. People want to open top loaders to add fabric softeners and when we have opened them so that they can add the fabric softener they are often disappointed with the level of water in the washer. Those people consequently refused to use those particular washers. People have pressed the buttons on the control boards and sent the machines into a loop; different readings have appeared on the screen. Some of them say out of order, sync and several other error codes. Eventually the machines reset themselves or I have had to reset the programming. In the meantime the people pass the word and those machines are not used by those who hear. The controls are too sensitive and are not suited to a commercial coin laundry.Whenever any buttons on the control board are pressed the time of the wash appears on the board. Because of this some people who are busy and are using and loading several washers claim that they have already put their money into the machines; they argue with the attendant or with us. Many times they actually believe that they have placed money in the machine and many times they try to get a free wash from us. Either way they are unhappy and they, and those who hear them argue, will not use those washers again. In most cases we lose them as customers and once customers are lost they never return.I placed them in a location where the previous Maytags had been heavily used, expecting them to replace the old machine. I was wrong. They are used very little and the long and short of it is that we are losing money and since our busy season is coming up, will be losing even more customers and therefore more money. I spent close to $12,000 on the machines, including delivery and installation and right now they are quickly becoming heavy paper weights. I have contacted the salesman who sold them to us, but he has given us the runaround and done nothing about the situation.

After 15 months of use the Maytag Dishwasher MDB8959SBS2 the control panel start malfunction. I read very carefully about the Home Depot Customer reports before purchasing this built in stainless steel dishwasher, and supposed to be one of the top notch on the market, around $850 retail price. It becomes a big disappointment. After three months of use, the top rack handle broken but it still under manufacture warranty, so we get it fixed by Maytag contractor. Then 15 months after regular use for a family of five, the control panel start malfunction, few bottoms will not start anymore. We are out of luck with one year manufacture warranty and working towards our VISA card extended warranty to try to get it fixed.

The paint (stainless steel) on the top panel surrounding the digital screen is deteriorating from the heat and steam from light cooking. This happened the first time I used one of the back burners for light simmering. I purchased the range in December 2011, but had not used the back burners because I dont cook large meals. The black paint on the range top is also easily scratched when moving the grates for cleaning. This product has defective paint and Maytag has NOT responded to my questions sent to them by email. I will never purchase another Maytag product NOR will I purchase appliances from HOME DEPOT again. Home Depot should not sell shoddy products!

I would say you have plenty of options when choosing a color for your dishwasher. You can choose black or stainless. Try one today you wont be disappointed. I load plenty of dishes into the space. It has extra pockets for little things and it has plenty of hooks and hangers to use for bigger cycles. Kenmore Dishwasher runs great. Very efficient and cleans the tough stains better than any dishwasher Ive ever used. I would recommend this to anyone looking to buy a dishwasher. Of all the dishwashers I researched at Lowes and Home Depot and Sears and Ace and other local stores, the Maytag was the lowest price with all the features I wanted.

Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

We purchased all new appliances 3 years ago including a Maytag dishwasher. Same problem as a lot of others. We had the control board fail three times in just four months. Now today the repairman came and while he was here contacted other Sears technicians and Whirlpool technicians. They came up with the idea to replace the detergent dispenser which they said is causing the main control board to fail. However, while the tech was on the line with Sears and Whirlpool they done troubleshooting on the detergent dispenser and found that it was all within specifications. In fact, that was not a problem because it worked as it should. But in their wisdom they decided to replace the detergent dispenser. We now have to wait another ten days for the part to arrive and reschedule another appointment to have the detergent dispenser that works replaced. The serviceman that was at our house said that they are making him replace a part that is working and that this does not need to be done but he has to take instructions from Sears technicians. Our service person said that he doesnt anticipate that replacing the detergent dispenser will make the dishwasher work but he said if it does it will only last a few weeks as before and then fail once again. We have the dishwasher on extended warranty and there are about 22 months. I suspect that this one will be going to court to get resolved. Never Maytag again or Whirlpool.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

The washer I bought brand new has never worked well. The clothes end up all bunched and twisted up together. The bleach is not distributed properly, I have big blotches of white spots. It is leveled, still shakes and everything is on one side