I purchased my first Maytag (Bravo Washer) appliance in 2013 and thought this washer would last me for a minimum of 10 years. It started making noises occasionally right away but I wasnt too concerned until it started sounding like someone was banging on it with a sledge hammer. I waited 8 days for a repairman who told me the bearings were going out and it would cost $400-500 to repair. This is the worst washing machine ever manufactured. My advice is to buy any other brand. Dont be fooled by the Maytag hype. Their quality is nonexistent. I am shopping for a new washer.

I bought a Maytag laundry set (washer and dryer, models MVWC565FW and MEDC555DW, respectively), and I concur with the fact that this is the WORST laundry set I have ever owned. The clothes came out of the washer extremely dry and did not come out as clean as expected. In addition, clothes came out with strange spots, especially the dark ones. Now, we wash our dark clothes with fear of damage them. The dryer is also pathetic. I put in a normal load on high for 60 minutes, and theyre still very damp. Sometimes I have to repeat the cycle 2 or 3 times. When I compare it with my old laundry set, this is extremely disappointing. And to make things worse, the customer service department doesnt answer you. I sent them a mail, on February 2018, and a month and a half later, I havent heard back from them.

I had noticed the lights, such as for sanitizing cycle, hot water cycle, etc, would go out intermittently, but since the washer still ran, I was down with that. Loaded it up last Sunday, pressed the button to start and El Zippo. Nothing works. So here we go again with another crap product from Maytag. Yes, I have had this dishwasher, which was a pricier model but closeout priced, at Lowes in 2008, BUT I live alone, so how many dishes do I wash. At the same time this is the third time had a repairman out (with no help from Maytag other than trying to sell me an extended warranty for nearly $400) and these machines ought to last a lot longer than this. The part online is bad enough, $150, cant wait for the repairman to call me back tomorrow and see how much they are going to hose me for.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

My old washing machine was about 25 years old but still doing a fantastic job getting the laundry done. When the dryer died we decided to replace both machines so theyd match. I had been setting money aside for years in preparation for this purchase. Ive only had them for two weeks and I stay awake at night wondering what GENIUS decided you can get clothes cleaner in a tablespoon of water than you can in an adequate amount of water?! My old washer could wash a load of laundry in about 20 minutes. Again, what GENIUS decided taking over an hour to wash a load of laundry in a tablespoon of water was a better way?! What working woman would choose to double the time needed to do laundry and then not feel confident that the clothes are clean?!!! I am so mad and frustrated and disappointed and I dont know what to do. I wish I could yell at somebody!!!

I have a 4-year old Maytag refrigerator. The back of the top freezer compartment is frosted and frozen, and the bottom refrigerator is now too warm to put food into. I wonder if a lonely non-busy Maytag repairman can come and fix it? Oh wait! Thats the deceptive false advertising that I bought into when I wrongly assumed that these were great appliances. I cant afford to get this fixed and after what Ive read from other peoples experiences, it wouldnt matter anyway. It would just break again anyway. What a joke! Ill unplug it and try replugging it in after it thaws and maybe that will work.

Ice maker not making ice, lights on the temperature controller are all flashing, ice/water dispenser door continuously opens and closes, refrigerator and freezer both do not cool/freeze properly. I purchased a new main control and low voltage board at a total cost of $400 and replaced them to no avail. Nothing changed when electronic boards were replaced.

We bought a Maytag appliance package when we built our house in 2015. So far the exchange Fan burned out in the fridge. The element burned out on the range. The wheels broke off inside the dishwasher on the racks inside and the outside of the white dishwasher is rusting worse than 1959 Edsel. 3.5 years old. Broken and rusty. I called and emailed Maytag customer service and all they say is it’s out of warranty and they’re sorry. Things break I get it but if they said on the box when I purchased it that it would rust in 3.5 years I would have looked at and purchased another brand. Beware of the cheaply made poor customer service of the new Maytag.

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

I purchased a Maytag electric range model # MER8775AS in Feb 2012. While boiling syrup, the pan overflowed onto the oven door. As I began to clean up the spill I noticed that some of the spill had gotten inside the door on the inside of the oven glass. To remove the stain would require disassembly of the door. I called Maytag and complained of what I called a design flaw and they said, No, its your fault for spills entering the door. They even sent a condescending email to me informing me that if I needed to purchase parts, where I could get them. I designed appliances for years and this is another example of poor quality and lack of consumer service. I AM DONE WITH MAYTAG.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

We had a repairman come out and take a torn pillowcase out that was jamming. It worked for a couple of weeks, now refuses to start. We have decided to rid ourselves of the Bravos 300 washing machine and not deal with Maytag any more. I would not advise anyone to buy a washer of this type, as it never really got the clothes clean to begin with.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

We purchased a Maytag refrigerator model # MSF25D2EAS on 10-22-2012 at the Home Depot in Tracy, CA. On 2-2-2014 (15 months) we noticed a puddle on the kitchen floor. Upon inspection, we noticed that the refrigerator was not working. Went over to Home Depot and were given the name and number of the authorized Maytag repair dealer (A and E). The technician arrived on 2-5-2014 and replaced the compressor on-off /overload relay and charged $243.82. On 2-16-2014 (11 days later), the same thing happened again. The technician came on 2-19-2014. This time, it was the compressor at a cost of $800.00 plus the $75.00 service call. One can purchase the compressor online for $300.00 and I am sure that A and E buys it for a lot less. We thought about it and decided not to get it fixed because we did not know what else would go wrong and how long would the second compressor last. We talked to the Appliance Departments assistant manager and were told that Home Depot does not give any kind of consideration and she had worked there for 11 years and had not heard of any problems. She was not telling the truth or she was not aware of the numerous negative customer reviews online. She also informed me that I should have bought a warranty. We have bought quite a few refrigerators in 50 years and they lasted for many years. Home Depot sells inferior products. Maytag must sell these inferior products at discounted prices and of course, some stores are looking for larger profits. I do not trust Home Depot any longer and will not purchase appliances there anymore. It was a very expensive lesson - the price of the refrigerator, loss of food (twice) and the stress it caused. We bought a new refrigerator at Sears and it was not a MAYTAG.

I purchased Maytag Washer and Dryer 3-4 years ago, upgraded to the premium washer and dryer, SS drums and have been dissatisfied from the start. The washer was extremely noisy; we were told this was normal. The dryer began making strange noises just outside the warranty period, and the belt and pulley had to be replaced. I was shocked at the cheapness of the pulley design, but the replacement part was of better quality. The washer began making a horrendous squeak shortly afterwards, again, outside the warranty period. The repairman said that they were all like that, Maytag used inferior transmissions and that it would be cheaper to replace the washer than repairing it. My mother had the same experience with a similar model. Needless to say, I will never purchase another Maytag product. FYI, there are only three people in our household, all adults, light duty use.

My husband bought a washing machine for me, February 2019, based on my request for a top load and a quick cycle time. The first issue was that the washer and dryer was the wrong color. I didn’t realize that he had ordered a stainless steel set before I accepted it. When he got home and discovered it, he called and tried to get the correct color, and Maytag refused to correct the mistake. When the technician starts the washer and dryer before they leave to make sure it’s working, it immediately becomes a used item that they can’t sell is what they explained to my husband! The technician also didn’t remove a plastic bag from the dryer vent that I asked him to check on before he attached the hose to the wall! Took me 2 days to figure out why the machine wasn’t drying the clothes properly!This Maytag washer has the longest quick washing time ever! 40 minutes! I have had trouble from day one with getting laundry clean with this brand new machine! And I’ve been washing clothes for almost 30 yrs! I discovered today that this washer only washes for 10 minutes in the soapy water and then begins draining! Unbelievable! This washing machine that takes 40+ minutes to complete a load of laundry! This is the worst experience I’ve ever had with a washer in 30 years of doing laundry! Don’t waste your money or your time even to look at this machine! It’s a poor buy!

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

So disappointed in Maytag - I have a 2013 Bravos washing machine that if I had it repaired again (less than a year after I had it repaired the first time and just over two years since we brought it home) the cost is going to two times the purchase price. And because it is just out of warranty Maytag is doing nothing about it, even though they know there is a flaw in their design.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

I cannot even begin to describe my disappointment in these overpriced machines! Bought a 4-year extended warranty when I purchased and two weeks after warranty expired, my heating element went out on the dryer. This repair cost over 300 bucks. Six months later the washer was making some crazy noise and service guy could not find the cause...another $120 bucks. A few months later the same noise...this time a coin had slid under the bottom plate and caused damage to the machine...another service charge of over $200 bucks plus I purchased an extended one year warranty at $189 bucks. Thank goodness, because now it is throwing an LD code and will not drain. Oh and I forgot about the service call for the latch breaking on the dryer door...another $119 bucks. The repair guy felt sorry for me and didnt charge me for the part. Tangled clothes when washed and forever to dry. Next time I will buy an inexpensive set like I had before that lasted 16 years with no problems! This stuff is junk!

I purchased my which I thought was a stainless steel French door refrigerator in 2011 that I was getting a great product. Not even 3 months later I was using my warranty to stop the leak from my freezer now. Mind you, I paid $1500 so I got it fixed. 3 months later I called for repair again... Getting annoyed because this time the freezer came off track. 6 months later were chopping ice chunks up to stop the leaking on the floor. This lasted until last October keeping towels and old clothes around the fridge to soak up the water. This is so embarrassing especially if you have company over. You have a pile of crap soaking up water. I am a wife and mother of 7 children. I cant afford to just go buy another fridge. This isnt fair... I spent hard earned money on that magnet attracting stainless steel fridge and Maytag could care less. Im so disappointed and broke. Now I have to scrap it.

M1BXXLZYB00 - This is the worst appliance I have ever owned and I am 56 years old. Very noisy, freezes my produce and actually anything in the refrigerator. Yet the freezer wont freeze popsicles. Had 2 service calls on the fan and or fan motor in the first 6 months. Now 2 years later we have replaced 2 compressors and had to pay 200.00 labor to have installed. Now the compressor is out again not even 30 days after the first 2. Whirlpool wants to send another compressor and the poor repair guys are suppose to do it for free now because it is within the 30days. The offered me to buy another refrigerator with prices of 699.00 and 519.00. My fridge in the garage is way more dependable than this one and I have had for 10 plus years with no problem.

I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

Purchased a Maytag microwave/range hood in 2005. So yes, it is almost 10 years old but should the handle break off in ones hand? I would say poor material is the culprit. No use contacting the company by the looks of it... they dont stand by their product. Warranty says 10 years but broken handle would likely be cosmetic...

We purchased a Model MDB8949SAWO Maytag dishwasher in September 2012. The control panel failed in November 2015. We wrote a letter to Maytag (Whirlpool) expressing our disappointment and received a call from Maytag customer service. The Customer Service representative informed us because we contacted our local repair facility directly, no reimbursements would be provided. During a subsequent follow-up call, I was informed by the Customer Service representative that Maytag manufactures quality products and that no premature failures were occurring with Maytag dishwashers. The Customer Service Representative stated that we should have purchased an extended warranty which lends some support to the fact that Maytag dishwashers are essentially junk. Never again will we purchase any Whirlpool products.

We purchased a Maytag refrigerator Model # M1TXEMMWS02 and Serial # E01103420 in April of 2010 from Home Depot in Aurora, Illinois. First off, we did register the fridge online via Maytag which of course, they have no record of! Now, we go on vacation and come back to all of our food ruined because the refrigerator stopped working! No refrigerator should stop working within two years! I called Maytag and they offered me a Repair Plus One package of $302.73! Are you kidding? We paid $400.00 for fridge. Then of course, only one-year warranty and have to pay at least $75 for a service call, labor plus parts! If it’s the compressor, the charge is $326.20, plus shipping and handling! What a joke! There needs to be longer warranty and should offer free service calls and much more. I am disgusted in Maytag products and in which we purchased due to a reputable name! Never again.

We purchased this dryer a Maytag Model MEDC200XW3 about 10 months ago. The dryer slowly over time began to take longer to dry our clothes. After watching it work and seeing that the airflow in the tube was not flowing well, I noticed the lint trap was not functioning well enough and over 50% of the lint was escaping the lint trap and plugging up the exhaust vent. I asked Maytag for a service to repair my dryer and explained my findings. The service person on the phone wanted to send me a lint brush. I told her to send a repairman. The repairman said that all lint traps let lint by and said it was my problem. Well today theyre closed and I cant even leave a message. Now I know why the Maytag repairman is the loneliest man in town...

I purchased a Maytag Bravos line washer model # mvwx500xwo back in Oct. of 2010 thinking that it would be great to save money on the water bill. I first had issues with it putting holes in my clothes. I then found out if you do not zip up all zippers and button all buttons, the machine will rip them up due to the high speed spin cycles. Now, the washer will not fill with water or start the wash cycle. I mean really, its less than two years old and I have to shell two hundred plus dollars to fix a washer that only cost $500. I guess I know what brand not to shop for next.

A little over two years and my Maytag dishwasher needs 300 to $450 in repair for circuit board or boards. The repairman said that they got cheap and left out a seal which allows moisture to get into the electronics, duh. They have a known problem but will not stand behind their screw-ups. Never again will I purchase Maytag, Whirlpool or any other product made by the bumbs.

I bought a Maytag Bravos top loader in Oct 2011. About a yr after having it, it started having problems. At the end of the cycle, theres still water in the tub and clothes are soaked. A couple of months after that, it started completely skipping the wash cycle, so the clothes would just sit in dirty water and do nothing. I called the small appliance co. I bought it from and by the time I get done paying a house call and parts, I might as well buy another one. I called Maytag because it seems theyre all having the same problem and at some point youd think they would be responsible for their product. They couldnt care less and the options they offered me were a joke!! Please, whatever you do, DO NOT BUY A MAYTAG because you will be on your own if anything goes wrong (unless you want to pay them the price of a new washer!!).

Didnt even want to put 1 star but that is the lowest you can give. Maytag microwave less than a year old paid $350. Door clasp broke. Took two weeks to send a repairman out, he came out and of course did not have the part -- took another week to get it. Fixed the door and then he crashed and burned the microwave shorted it out and now it is totally dead. That was 2 1/2 weeks ago. Maytag refuses to replace the microwave and insists that the same incompetent service company come out and fix it. Meanwhile I have to call Maytag every other day to find out when the correct part to repair the microwave will be in. Was told it would be in two days ago. Never got a call to schedule the repair, called today to find out they never even ordered the part. Here goes another week without my microwave. Not only does Maytag have horrible customer service, they manage to find unskilled repair techs with equally horrible customer service! Will never ever buy another May useless Tag appliance again.

We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

I bought my Maytag about 3 years ago. Have had continuous problems and now the whole barrel has broke and dropped down. I was treated with disrespect from the repair man and will never buy another Maytag washer.

Everything in my house is Maytag. I assumed they were the best. My dishwasher went out after three years, and I replaced it with a Maytag. Now, my over the range microwave is not working. I will not replace it with Maytag. I expect my washer and dryer to be next.

The washer does not clean clothes. Thank goodness I bought a 4-year warranty because they have been out 4 or 5 times on washer alone. The dryer is now squealing and shuts off (a safety feature I am sure). The repair person replaced the pulley system and one belt, it still squeals and shuts off. I called the Maytag CEOs office and talked to a machine. Some really nice lady called me back and said she cannot do anything to help me. They have no consumer person to help you and troubleshoot with you. The washer is rusting, it is an inside washer. I live in SE, Texas and they told me it was due to living close to the coast. Well, Ive had GEs that never rusted and in fact, the problem is really with all the HE washers. I hate them. They do not clean clothes. I will never buy another Maytag or Whirlpool product again.

We bought our beautiful Maytag refrigerator model MFI2568AES at our local Home Depot approx. 4 to 5 years ago. The refrigerator stopped cooling last week and we had just renewed the warranty for 3 years. The service repair stated that the problem was not covered (internal corrosion) and they could not do anything for us. Is this how long Maytag refrigerators last? Home Depot was also not willing to do anything for us. Were very upset and disappointed and using ice chests for now.

Update 3/7/2018. I have been without a working microwave since 1/23/2018. Technician sent from Maytag came out to repair it and said he needed to order a new board and door switches. These items were installed on 2/26/2018 but did not solve the issue. The technician said the microwave needed to be re-wired completely and would schedule for the microwave to be removed and brought to shop where it would be repaired. After I called Maytag and explained the situation they told me they would replace the microwave (with the same model.) I called today to get an update on when the new microwave would be installed and they said not for another 14-21 days!!! After expressing my displeasure at the whole situation I was told by the Maytag representative that I could choose any new microwave model (under $399) from the lines of Maytag, Whirlpool, Armana, or Kitchen Aid. It would take about 14 days for delivery and they would schedule the installation at no additional cost to me. So now I am researching microwaves again!!! Ill update this review once the new microwave is installed.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

The washer does not get the laundry clean. It never has. I use only HE soap. I have changed soaps several times and still no change. I have been very disappointed with it. Maytag has been advertised as a good washer but the Bravos is not.

Maytag model #MDB6949SC, purchased Feb 22, 2015. In early May plastic parts from the top rack wheel assembly broke. Assembly unit replaced at no cost through the 1 year warranty. (cost = time and effort to arrange replacement with repair person). Same parts broke again in November - replaced at no cost again under warranty. Warranty expires in two months. If past performance indicates future performance, this part will need replacing twice a year at ~$140 per visit or $280 per year. Not a good thing. Called Whirlpool and with several calls and emails. They offered an extension of a year on the warranty. I think using plastic for this wheel assembly unit is a design flaw. Would not recommend this dishwasher.

Do not buy a Maytag dishwasher with model # MDBH969AWB1. I bought this dishwasher last Dec. 2010. I could not use it for 2 weeks, because the door would not shut. The repair man came & fixed the door. Then when I actually got to use it and after it finished running the cycle, the tub was dripping with water all over--top, sides, door, bottom. I had to dry the dishes on the top rack, and I had to leave the door open for days in order for the inside to eventually get dry. The first thing I noticed about this dishwasher when it was installed was that it was smaller than my other dishwasher. I hate the design because of the way they have made the racks plus because it is smaller--it holds less dishes than my old one did. I could actually get almost twice as many dishes in my old one than I can with this one. Do they not think of asking the consumer about what they want in a dishwasher instead of going ahead and making something that is not functional?I am so frustrated with this thing; it has brought me to tears. I just today went to Sears and looked at their Kenmore dishwasher. It is designed more like my old one than any of the other makes out today. I wish I had checked this out, before I bought this Maytag. Weve always heard how Maytag is at the top of the line with no problems, right? Dont believe it. I will never buy another one. Whoever is designing these dishwashers need to go back to 1990 and take a look at how it was designed and then go back to making them like that. I loved my older dishwasher, and I wish I had never let them take it away. I wish I had taken the money I spent on this ridiculous Maytag and had my old one fixed no matter what the cost. I made a terrible mistake.If you have an older dishwasher and it has given you good service for years, I suggest you have it fixed and keep it, because you will not like the performance of what they are selling today. It does not matter what brand you buy, they are all designed the same. Just take a look and compare them. But if you buy, please check out the Kenmore. I dont know if the performance is better, but the racks are better designed. My old dishwasher was a Hotpoint. It was the cheapest one on the market, and it gave me the most wonderful service ever. The dishes were always very clean, the heating element was fantastic, and it always dried the dishes completely. I cant believe they would make a product like they do today and sell them for what they do. The heating element in them today is not as good or strong as what they used to make. That is why the dishes wont dry properly. You get way less than what you pay for. Thinking a new dishwasher is the way to go, think again. Please, if at all possible, keep your old one and have it fixed over & over again. I hate this dishwasher. What a joke on the unsuspecting buyer.

Dual oven - one is a convection oven. Never used the bottom drawer so that was wasted on previous range. I purchased a white appliance to match my others. The white stove top is a pain. Too bad it wasnt black. I checked this model online and found a good price in the city. I contacted the local Home Depot and they did a price match less 10% - all a bonus. The ovens work great although I have not tried the self clean. I have read that similar models have problems related to the self clean feature - high heat and circuit boards. My plan is to have a fan directed at the top of the stove when I use it and the range hood fan going. The convection oven is great - hard to mess up a recipe with that. The dual ovens are truly a great feature - strongly recommend. The keep warm is great also - nice to have two things cooking at the same time. That being said - the bottom oven is low, but that is worth the extra cooking space.

I didnt want something from Sears due to horrible experiences with them. Maytag is very reliable and the cost was reasonable. They fit in the small space available for washer and dryer. They have all the features I need. The only complaint I have about the dryer is that for some reason if the load is small, it takes longer to dry than with a full load. I have had them for about 5 years now. I expect a washer and dryer to work correctly every time. If its poor construction I would not buy it. I also expect an appliance to last many years with proper maintenance.

Same issue as everyone else. After about 15 months the control panel on my Maytag dishwasher model#MDBH979SAM1 has malfunctioned. First it would only let me choose the rinse option but now all the lights are turning on and the dishwasher will not stop washing but yet the dishes are still dirty. I called Maytag and they quoted me 249.00 to fix the issue. But if its a common problem with this make and model why do I have to pay to replace the panel. They should recall this model or replace the panel with an updated one that wont have the same issues! I cant imagine paying 249.99 every year to replace this panel that seems to malfunction no matter what you do!!! I paid around 550.00 at the home Depot for this dishwasher! It did not even last me two years!!! I want a lawsuit filed against this company and I want my money back or my dishwasher replaced with one that works and wont have the same issues!!!

The AquaLift Self-Cleaning is a very poor substitute for a normal high temperature Oven-Range. It gives as much work as an oven without any self-cleaning, as it does nothing to the sidewalls or the door. The minimum temperature is 170 Fahrenheit, too high to rise a dough.

Purchased washer in 2015, worked pretty good for 4 years. In 2019 belt, support rods, and control board replaced. In 2020 clutch, pulleys, and suspension replaced, waiting for service technician to replace transmission later this week. I purchased extended warranty thru Lowes, glad I did as the machine literally jumps in the air during spin cycle. Lowes stated I needed 4 repair visits to place a claim for replacement! Machine will not spin properly on high speed. Luckily I have a spare machine in the garage to use while I waited for repairs to be made. However, nothing seems to be correcting the problem. Very disappointed in the Maytag washer.

This is my second washer in less than 5 years, going third. No customer satisfaction. Maytag/Whirlpool dont care, Customer Service doesnt care - all I hear when I call is, “too bad”, “so sad”, “call a repairman”, so you can spend another $100.00 plus. I hope this doesnt happen with someone elses brand when we buy it. Shame on such a big company.

They are coming for the 7th time to fix the ice maker. Three full replacements. The bottom of the freezer had a buildup of ice, another call to repair. I know where the Maytag repairman is, hes at my house.

We purchased a Neptune washer/dryer combination with pedestals a few years ago. The washer vibrates so violently that I had to block it between the dryer and wall to keep it from walking across the floor during the spin cycle. We had a technician come out, and he stated that the unit just needed to be balanced. The level I used showed the washer balanced in all 4 directions. Then he said I had to balance it with the machine running to stop the vibration. That didnt work either. I had previously installed vibration dampers and the technician told me that makes the vibration worse. When is someone going to file another class action lawsuit against Maytag, as there appears to be thousands of complaints for this same washer?

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

I have a Maytag Bravos washer that has gotten to where every time you try to run the final spin, you get an unbalanced load code and it shuts off - it does this even when you try running it empty. This washer is 3 years old, and has been doing this progressively worse for the last 4 months until now. We cannot even get it run the final spin cycle now.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

We purchased a Maytag Bravos X washer 2 years ago. Theres not enough water in there, and the clothes get so tangled that Ive had holes in them. Ive had technicians come out several times and they just say that its the water saving feature of the washer. I put it on the wrinkle control setting and the clothes come out ridiculously wrinkled. All of these problems are due to the water saving feature. I absolutely hate this washer and would never recommend it. I want my old washer back with the agitator and enough water in there to actually wash clothes.

We bought this Maytag washer 3 mo. ago and now need work done on it. We were told that they could not find anyone willing to come work in this area. We live in the Mississippi Delta, 30 miles so. of Greenville, 50 miles no. of Vicksburg or 90 miles from Jackson. So I guess the Maytag repairman is not just lonely anymore, he doesnt exist.

Our 26 month old Maytag fridge (Model MFF2258VEM8) was the french door freezer on bottom modern style fridge. The freezer stopped working. The repair shop took the fridge away and repaired a leak (quality control issue) and then the compressor failed in a test. They wanted $700 to make a repair that would have a 90 day warranty about 1/2 the cost of the fridge. Maytag was contacted at multiple levels and they would not even provide a free compressor or provide a substantial discount on a new fridge. What a way to treat a customer who once had all major Maytag appliances in our home. We decided to get a GE Profile fridge and are very happy with it. I will never buy another Maytag appliance. I dont think it is the great company it once was years ago.

I purchased the Bravos XL washer and dryer combo 2 years ago. Dryer is fine, but washer was EXTREMELY noisy from day 1 and has gone downhill since. It would leak during spin cycle and frequently stop due to unbalanced load, refill and stop again. Now it wont spin at all! We have checked to make sure it is level, it is. I live in a very rural area and its very difficult to get repairmen to come out. This is my first and last Maytag for me.

I am happy with this dishwasher. I had a GE that had a lot of problems. I insisted on getting Maytag and I have been happy ever since. It controls the time, temperature, and is easy to operate. I would like a bigger dishwasher because of my family size. This dish is okay for a family of 4. It matches my furniture. It blends in. No complaints. The digital pad is convenient but it has been fixed a few times. I had a few technicians who did not know how to fix. It was not the dishwasher, it was the technicians.

After buying this dishwasher model MDB6759WWW3 in Jan. 2010, I fully expected it to work longer than it did! So far, the control panel has been replaced 5 times. The last time was Sept. 17, 2012 and already it is out again. I talked with Customer Service, since Georgia has a lemon law. After 4 times it is to be replaced.They had no record of the part that was replaced, just that a technician had come and repaired (by ordering the same part they had no knowledge of). This time they will either replace or instead of me calling, my lawyer will call. I will never buy another Maytag product and will encourage anyone else not to buy either. My daughter had the same experience with a refrigerator, a piece of junk they did nothing about. By the way, I have an extended warranty plan, which should not even be necessary!

Maytag Smoothtop Double Oven - Bought this stove 2 and 1/2 months ago and already buttons arent working. Very disappointed, not getting a Maytag again.

I bought a complete kitchen: stove, fridge, dishwasher microwave. Suppose to be stainless steel. All have rusted out within 6 months. Maytag does not stand behind their products. They sent me cleaners and all my appliances rusted more using their cleaners.

We bought a Maytag Centennial Washer in 2011. 6 months ago the control board went bad. Maytag has an exorbitant replacement price! I went to Ebay and bought a NEW board for 1/7th of the price Maytag wanted. The old board was marked revision B. The new board is revision F! That indicates to me that the board was defective when it was new and they have made 5 attempts since then to fix it! No recalls however. Now the motor is shot. I found out the motor from Australia is also inferior! So this 5 year 3 month old POS Maytag is going to the dump! We will shop for something made outside the US. No not a Samsung. I think there should be a class action suit against Maytag.

Recently purchased Maytag Washer and Dryer from our local Home Depot June 2020. The appliances were finally delivered in August. When both appliances were installed, the installers made sure the washer was working properly and there were no leaks. They did the same for the dryer to make sure it was working properly. When the dryer was turned on however, the motor blew up and there was smoke coming from the dryer! I am now sorry I purchased Maytag. I had narrowed my choice between purchasing Samsung or Maytag. Im now thinking I should have gone with Samsung. Im supposed to receive another dryer today. The washer works, however its very, very loud. For the amount of money I paid, I hope these last for a while.

I bought my Maytag Model LA608 washer in 1976. It has very few electronics and a mechanical timer. It has been used every week since then for 2 or 3 people. It has had 3 problems in its lifetime. I replaced the 2 valves that control the hot and cold water entering the machine. I replaced a small plastic sprayer part. And last year I replaced 3 clamps that rusted and started to leak. Thats it in 40 years. I was able to open up the front and back covers to get at the parts quite easily.It is a simple machine with almost no electronics to stop working. Nothing bothers me about the machine. Its simple and wonderful. When it finally breaks, I will try and find a good sized machine that washes permanent press and regular clothes, has a controller to select hot/cold/warm water temperatures, has a regular and gentle cycle, and has 3 load levels for the water to be used. I will try to find one that is good quality with few electronic parts. I will not buy a high efficiency model that uses less water as I am on a well and water shortage is not a problem where I live. I will not buy a front loading model.I would not buy a machine that has options that I do not need. I would hope to find a quality machine similar to what I have now. I would read as many ratings about the various models before making a selection and then I would cross my fingers and hope for the best. If it is possible, try and find a good quality machine that will be dependable over time. Buy a basic machine with only the options that you really need. There will be fewer parts to stop working.

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

I purchased my 2nd Maytag Neptune washer in 2005 to replace an early Neptune that was complete junk. This one worked OK until this year when it began to make awful noises. After research, I decided it was the bearings that failed. I took the unit apart to get to the bearings and found out the entire outer tub must be replaced not just the bearings, at a cost of $515. What lousy engineering, the bearings dont come out of the housing. No wonder Maytag repairmen are so bored. There is nothing to fix, you just buy a new washer. I wont buy Maytag this time.

This top load machine replaced a top of the line Maytag Neptune. It has five water levels. It has three temperature settings and four wash selections. It also has a selection for an extra rinse that I use for white loads. The washer is very reliable. Clothes come out clean with an average amount of detergent. Although this washer is more than fourteen years old, it has never needed service or repairs. By running a cleaning cycle every six months, it drains like brand new. The stainless steel drum is still as polished as it was when it was new. Even the hoses have lasted with a need for replacement.

I have a Maytag purchased about a year ago. My old Maytag lasted 16 years. The salesman told us that they are now built to last 8 years. It’s pretty noisy, so much so that I have to close the door to the utility room. I guess it gets the clothes clean but it used very little water. Fortunately my model has an agitator but nothing like the old kind. After looking at many models, I feel this was the best choice for the value. It is top loading which I like.

My refrigerator temperature control panel started flashing lights and the ice maker flap started opening and closing over and over. I checked online and there are numerous model #s doing the same thing, most all contacted Maytag, some were fixed for no charge. Some were not even though they admitted there was a defect in the electronic control panel. I was one of the ones they refused to fix because they said it was an older model but they fixed a 2006 model, a defective part is a defective part no matter the age especially if they know and admit there is a problem with the control panel.I cant understand why they wont take care of their problem, so now I have to spend over $300.00 to fix a problem that they made in manufacturing, that is not an outrageous amount, thank goodness, but I just dont understand why they wont stand behind their product when they can fix out for probably half that cost to take care of their problem. I didnt make the refrigerator, they did.

I have a 50/50 chance of completing a wash cycle. Most times, the washer stops working at 8 minutes remaining in ANY cycle. The washer will leave me with wet clothing and refuses to spin even when most wet, dripping articles are removed. I have tried to put all light-weight items together and that still is not a guarantee that I can get this done in one cycle. Most often, the error code comes up, I spin the drum around, move the clothing around and try again. This process is NOT energy efficient which is why I bought the ** thing in the first place. I am ready to put it on the curb for the trash man to pick up.We had a service person out and he said it is either the bearings or the motor (both a $400 job). I will NEVER buy another front-loading washing machine. At least with the old-fashioned top loaders you can get the load balanced and at least get clothing to go through the spin cycle. I am now hand-wringing clothing once again since the machine tells me when it will spin my clothing. That stupid chime is about to send me out of my mind!

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

I have just joined the open and close the door Maytag Club. Purchased four Maytag products on Black Friday 2017 as I always trusted Maytag. Only disappointed to have my microwave (MMV4205D-4) come down with the virus (open & close door) that has plagued so many unsuspected owners. Almost made its 1st year anniversary. Now I see this has been going on for years and all they do is add different model numbers at the end. Luckily Im in the 1 year warranty and repairman coming next week. Now I question if I should take the extended warranty as I see this is going to happen again down the road. And will the extended warranty cover it? Guess the Maytag repairman isnt sitting and waiting for repair call anymore. He is being kept busy!

This is a Bravos MTC machine. It is a top load and has an energy star rating. Made in the United States. Impressed by its low water usage and Its ability to clean clothes. This particular model comes with a 10 year limited parts warranty, drive motor and washbasket.

We have had this refrigerator since January 2011. All was OK for 18 months. Then the lid to the deli drawer fell off, the plastic bar that holds the two drawers up broke (weve had to use roof shingles to prop them up) and another one of the plastic pieces crumbled. Now the ice maker wont work and the refrigerator makes a loud ticking noise. There are only two older adults here and we have not treated this appliance roughly. After reading all the complaints on this site, Im wondering if any of it is worth fixing. My GE refrigerator worked for almost 20 years.

Im told even though my fridge is leaking water and making sizzling sound nothing can be done and my model number and serial number match the recall for this product and I was told that if my fridge catches fire then, Call us but to me thats ridiculous.

We too were having a water leak from the French door freezer and a sheet of ice under the freezer drawer. The repairman came and told us that it was a common problem with the French Door fridge and an easy fix. Maytag has a new P type defrost hose that doesnt freeze up. He changed the part, $149.75 bill, and no more problem. Should Maytag have let consumers know this was a part that was failing? Yes, definitely. But at least the fix was reasonably cheap.

I really like my Maytag dishwasher. It has been very good. I have had it for at least 10 years and it is still working fine. It is worth every penny. If this one stop working I would buy another Maytag dishwasher.

Maytag Frontload washer MHWE300VW12 - I bought the washer and dryer in 2010 through Lowes. In Dec. 2012, it started making a loud sound when it would be in spin cycle. I called for service. When the repairman came out, he said the rear seal/bearing was bad and has gone out. The part and labor cost would be $1,184.36. Come on, are you flipping kidding me? Thats twice what I paid new for the washer. I bought them for the Maytag name. If I would have known it was a Whirlpool, no way I would have gotten them. My mother had a Maytag set that lasted 30 years. That explains why they dont show the commercials with the Maytag repairman that wouldnt have anything to do. Also, when the parts came in, they were Whirlpool parts. What a scam. Just more junk for our landfills.

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

Two years old, single person owned and will not operate - At 2:00 am, April 25th, 2012; I went to take a load of laundry out of the washer. It was still full of water and would not operate. I am a single person. I do not do load after load in two years. In fact, I was doing a weekly load of clothing, nothing large. I paid close to $1,000.00 for this unit. This sucks and why only one year warranty? Are you Maytag? A Youigo car would run better than this. And they are built cheap.

Faulty Maytag MDB8969 Dishwasher - BEWARE! Whirlpool, Jenn-Air, Amana, Maytag, KitchenAid... Are all brands that fall under Whirlpool. According to Better Business Bureau statistics there is less than 1 chance in 10 that you will get the Whirlpool product you are expecting! We purchased a new Maytag dishwasher at the end of 2016. Within a couple of weeks the dishwasher began failing: discharge pumps, heating elements, soap dispensers, door leaks, faulty racks, rinsing problems... Since purchasing the machine we have had to make 7 different service calls, all under warranty. The warranty service providers have been good but the machine has been a catastrophe, having been out of commission for several of the 18 months since being installed, and causing serious water damage to our kitchen floor (based on several other negative reviews this leaking is not an uncommon occurrence).A few months into owning the machine, after our 3rd service call, we contacted Whirlpool, Customer Service and asked for the machine to be replaced. They refused to replace the machine but extended our warranty free of charge- better than nothing but not a cure to the problem and the only remedial action that Whirlpool was willing to offer. We didnt understand at that point that the problem of faulty and defective Whirlpool products was probably so huge that Whirlpool could not afford to provide a reasonable solution to their customers; leaving many, as witnessed on various product review sites, to bear the extreme frustration and associated expenses borne from the incurred failures. Unfortunately, here we are once again, requesting our 7th service call in less than 18 months, and asking once again for a replacement.The Whirlpool response this time (CSR was not allowed to let us speak to her Supervisor in spite of trying to negotiate that for several minutes) was that they would not replace the defective machine but would sell us a new $850 machine for $250 and would dispose of the faulty machine for an additional $25. Whirlpool would not however pay for the uninstall of the faulty unit nor the install of the new unit (about $350) which would have to come out of our pocket. We won’t be spending the additional $600 to fix this problem as proposed by Whirlpool; we won’t be installing another Maytag product in our home. We were advised that we could fill out a form if we wanted, to try and claim for the damages which the dishwasher caused to our kitchen floor. The form was never emailed as agreed and now we are just really tired of the whole experience so will simply put this all behind us.Our Whirlpool experience has been extremely stressful and quite expensive. It is clear to us that if an appliance which is averaging a serious failure every 3 months since the first day of installation, does not in the opinion of Whirlpool warrant a full and prompt replacement, or even the direct telephone attention of a Customer Service Supervisor, that the Whirlpool quality standard must be so low, the failure frequencies so high, that the number of similar failures prohibits any commercial viability to manage the problems in a reputable manner. Whirlpool clearly has some very large problems. It would not have been easy to destroy the once highly respected Maytag name. Such degradation could only take place as a result of continuous and ongoing Whirlpool quality degradation. We will no longer be their ‘crash test dummies’ but I do hope for the sake of Whirlpool (apparently North American made) that they take ownership of their poor quality condition, realign and spend the next few years becoming the company that we all once knew and respected.

I have a bearing going out. The Bravo washer makes a terrible noise. Now, they tell me I need a new tub/bearing. This repair will cost me more than $250.00 plus service calls. This is the second repair that I have had on this machine. It is only 4 years old. I use it twice a week. I will not recommend Maytag to anyone and I will never buy another one. They should check the internet for complaints and realize that there is a problem.

The unit has an ice maker. On a regular basis, water would accumulate at the bottom of the freezer pan. When the bottom pan got filled up, water would run out on to my hardwood floor. I related the problem to the ice maker. Researching the problem, I learned that the ice maker has an adjustment for timing the on cycle for filling the ice tray. After several adjustments nothing changed. I ordered a water control valve and installed it. The problem persisted. I installed a water pressure regulator but the problem persisted. I installed a water filter, the problem persisted. I turned off the entire ice maker and the problem persisted. The problem wasnt the ice maker. The real problem was the defrost cycle of the evaporator. The drain for the water was plugged with ice. I made modifications to the design so I could monitor the drain hole in the back of the freezer. Will I purchase another Maytag… probably not?

My refrigerator stopped working less than two weeks after purchase. The ice maker failed to produce ice. I feel they sold me a lemon. Yes, I do!

I attempted over and over just to swap out washing machines. I originally purchased a washer and dryer because of a defect in the top load they delivered. They talked me in to the frontload Neptune instead. Within months I started having daily reactions to mold and to my disgust found out it was from my washing machine. I begged to switch back to the top load I originally ordered and the store would not let me and referred me to Maytag who sent me some tablets and would help me no further. Apparently, the Maytag repairman wasnt lonely anymore if a product had to be manufactured and ready for complaint calls. Well I used the product. I used vinegar and baking soda. I have used hot water and bleach. I have left the door open to dry...It is the most cared for item in our family and the one that makes me ill literally. I cannot afford to buy a different one and would be interested to know if my husband’s declining health issues have anything to do with our mold issue or if it is just depression...Anyway, I was very discouraged to find out that other people in other states had washing machines replaced, but why didnt I? I would be happy if they could buy back my old Maytag that I had prior to this Neptune, I am sure it is making someone very happy somewhere. Why couldnt they have respected my very true complaint? I was not trying to get something for nothing. I paid for something to keep us cleaner and free from allergens and instead wash my clothes in mold and have mold spores leaching into the air in my home. Please help.

My 1 year old Maytag Bravos 300 dryer caught fire on Nov. 21, 2011 after the first one was replaced. Firemen came. Luckily, it didnt spread to the house. The first one wouldnt dry my clothes.

Most American dishwashers are made by Whirlpool. My control panel failed after only 3 years (design is terrible!). I had to pay almost 50% of original dishwasher cost to have it replaced by Factory Service Co. (formerly Whirlpool service).

I purchased a washer in July and its already off track. When I seen it I know it was junk but the sales person assured me it was a good product. 3 months later its off track. No spinning. DO NOT WASTE YOUR MONEY.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

We have had a Maytag Bravos XL top load washer less than a year. Big Mistake. It was JUNKYARD ready when it came out of the box. Does NOT wash clean. Weve tried everything.The agitator looks and acts like a toy. Will not run enough water to wash anything. We had a LG front load before and its hard to get use to having dirty clothes. NEVER AGAIN.

My husband bought me a brand new Bravo Maytag washer and dryer from Home Depot in November 2010. In May of 2011, we moved and the dryer hookup was electric instead of gas. My husband knew how much I love the dryer, so he surprised me with another Bravo dryer to match the washer. We put the other dryer in storage and were happy with our purchase until April. In April 2012, the dryer stopped working. It wouldnt dry the clothes at all, and every time we tried to dry, the dryer was filled with wet lint. We were only a week away from moving again, so we waited until we got to the new house. The new house had gas hookups. So, we put the dryer that didnt work in storage and were thankful we didnt get rid of the other dryer. Now, just a few months later, the gas dryer isnt drying and is having the same issues as the electric dryer. How very disappointing! Both dryers are broken now, and it has only been 2 years. Each dryer has gotten about a year of use and then both quit. My husband, I and my two-year-old dont do that much laundry to break 2 dryers. My old GE washer and dryer lasted for years and is still working. We gave them to my husbands aunt who uses them and loves them. I agree someone should start a class action against Maytag. These issues are ridiculous!

Maytag Neptune Stacked Electric Washer & Dryer. Had to buy a motor for Washer but lasted 12 years before giving problems again; then couldnt find anyone that would service for cheaper than $100 for just coming to your house plus $75 an hour for labor. Thats HIGHER than my billable rate! Rip-off Service & parts charges. Found out it was easier & cheaper to troubleshoot ONLINE myself using FIXYA site and others. Expense for an appliance above what most run ~ 1500 for both units. Plus if it doesnt have or offer a 5-year warranty then something is wrong with the quality! Maytag Neptune Series MLE2000AYW 27 Inch Electric Laundry Center with 3.34 Cu. Ft. Washer Capacity, 4 Wash Cycles and 6.0 Cu. Ft. Dryer Capacity, 3 Dry Cycles: White. Worst part on this model was a WAX MOTOR that they used for the Washer to control the door being closed or open. Next worst DESIGN error was they didnt put a drain hole in the plastic rim seal for the Washer door, that area would build up mold & mildew if you didnt learn to keep Washer door open at all times AFTER a wash. We learned by removing the light bulb! Therefore it was easy for my crew to learn to leave the door open after washing. This model was Energy star certified and had a long life here 12 years. Unfortunately I think they build these things to only last 10 years; then you have to replace them. In years gone by... the 1970s Washing machines and dryers would last 20 years!!

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

I also have a Maytag Quiet Series 300 dishwasher. The front panel has stopped working. It was a horrible dishwasher from the beginning. The dishes were streaky on the top rack. And I had to replace the rollers after just over a year. The upper rack has rust on it. The Maytag double ovens I bought at the same time had to be replaced within a year, as the racks damaged the porcelain interior. I also wish I had found your site before my purchases. My husband is not working now. So, I guess we will be washing dishes the old fashioned way.

We bought a new Maytag Bravo XL washer in 2015 under the understanding it has a 10 year warranty. Well it’s 2020 and it starting leaking. Called customer service and lost 3hours of my life waiting for a person. Keep in mind I’m pretty handy and work on spa, and pools. And can troubleshoot things like this. I found the problem on our washer looked up the part and number.When I finally got a person on the phone they wanted to send a technician out to verify what is wrong with it. I was all for that but then they said it would cost $100. I said no because I already know what’s wrong and just need the part so I could fix it. I knew the labor would not be covered under warranty so that’s why I didn’t really need the tech to come. After a few minutes Maytag finally says the unit is. It covered under warranty at all. I asked yes it is because it’s literally written all over the washer it has a 10year warranty. So then Maytag goes to say they only cover the drum and motor for 10 years.So now I’m stuck with a washer that leaks that was sold to us under the pretense of a 10year warranty for parts. And now having to buy $280 worth of parts and shipping to fix it. Maytag advertises that they have the best warranty and they never break as their commercials imply. So they represent themselves And their warranty falsely. Buyer beware. Maytag is shady. I’m guessing Whirlpool is part of them so please do your research before you buy. 1. Customer service doesn’t exist with them. (3hrs hold times.) 2. Misleading warranty coverage. 3. Will not call you back.4. Try to extort more money from you. ($100 to send a tech out to confirm what you already know.)DO NOT BUY!!! Learn from our mistake.