I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

I purchased the Bravos XL washer and dryer combo 2 years ago. Dryer is fine, but washer was EXTREMELY noisy from day 1 and has gone downhill since. It would leak during spin cycle and frequently stop due to unbalanced load, refill and stop again. Now it wont spin at all! We have checked to make sure it is level, it is. I live in a very rural area and its very difficult to get repairmen to come out. This is my first and last Maytag for me.

I purchased this machine less than 1 month ago. Have had tech here twice - he cant find anything wrong with machine. As for large capacity it will hold a lot of clothing, but will not clean them. I have had to put less than a 1/4 of tub full of clothing (about 15 small items). Use high water level, extra rinse, then rinse and spin again to get the 2 tablespoons of HE soap off my clothing. Takes over 2.5 hours to wash about 15 items. I have called Maytag and they will not back their product. I purchased at Home Depot and they said they have to do what Maytag says. Sending another tech out in 2 more weeks. Takes more water, more electricity, and more time to wash clothes than ever before.

My Maytag (MER7662XQ) oven has stopped working after barely 6 months of use. I filed a warranty-repair complaint and reported the error codes shown: F1 (faulty touchpad) and F3 (faulty temp sensor). Although Maytag promptly sent a repairman, he arrived without parts and left within 5 minutes without fixing anything. He said he would order parts. Whenever they were delivered to us, by mail, we should call again to schedule another repair. But he warned he was prohibited from coming out for another 7 days. So far, Ive been without an oven for almost 3 weeks and there has been no action or information. My calls to Maytag produced nothing, except confirmation they show the repair as open since they do not actually distribute parts, and the repairman is with an outside company. A terrible product and a worse service! I would not ever buy another Maytag product and recommend that no one else does either.

I have trusted Maytag for many years, more than 60 years, my parents and then myself. My Dad always told me I could trust Maytag over any other brand and that has always been true until I bought a new Centennial Econoserve Washer. This is without question the worst machine ever made. I should have asked every question in the book concerning this machine but, oh no, I just trusted the name MAYTAG. I am so sorry. I cant trust it to clean anything that shows it needs cleaning so you have to wonder what does it clean that you cant see. Im sorry people, I just dont know what to do. I cant afford to buy a new machine and the store I purchased are basically telling me, Sorry, you bought a stripped down model. Too bad! I will never buy another appliance from that store nor will I recommend them to anyone. Too bad since they are locally owned. Anyway, Maytag, you blew it badly to turn out this terrible machine. Thats my story and Im sticking to it. Better product next time.

I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

I purchased a Maytag dishwasher less than 2 years ago through Home Depot and did not purchase the extended warranty. The start button has stopped working and is not lighting up. I was referred by Pacific Sales, the appliance sales company at Home Depot, directly to Maytag to schedule repairs which I am willing to pay for. After a nearly hour long call between hold times and conversations I was told the service would be scheduled for Thursday or Friday of this week. As we were scheduling the appointment, I was told the computer for scheduling had gone down and to call the next day to schedule. I called next day and spoke with a customer service rep who said there was no record of my call the day before. I gave her all of my information, then she transferred me to another service person who then had no record of my two prior conversations. After giving my info to the this 3rd customer service representative, I learned that a repair could not be scheduled for over a week. I asked to speak with someone about my complaints and was told there was no one I could speak with but that she would pass on the complaint. I asked for a return call or email to confirm that my complaint was received and she said that I would not get that. I then asked for a free service call because of their poor customer service. This was of course denied. The dishwasher has been fine for the short period of time I have owned it but I wont buy another Maytag because of their poor customer service and because the dishwasher has a problem in less than two years. I am just writing this as a warning for other potential Maytag customers.

I did not purchase it. This range came with my home. The electric range works great. It is thorough and I dont have to worry about the gas being on and filling the house up. Electric may not be for everyone, but it is the way to go for me. I will look for similar if not the exact same make/model if a replacement is necessary. I dont mind spending a little extra to ensure the product will last. So many products dont last nowadays and it is sad. I am not an avid cooker, actually I tend to mess up a lot of food recipes but the electric range helps me to reduce the number of problems I run across with the durability and accountability of the product. It cooks throughout the entire dish/pan and I have never had a problem with the unit working properly, just the user not working properly. Haha.

This dishwasher was here when we bought our home. It has been heating up way too much on the drying cycle. I turn it off and air dry the dishes but today I noticed it melted my plastic measuring cup. I had the heat turned off and opened it as soon as it started the drying cycle.

On the first day, first time, the washer wrinkled clothes so bad I could not get them out. I talked to Home Depot people and they said I must lay clothes around tub like pictured in the book. I did that and they were still wrinkled. I called the repairman who said nothing was wrong with the washer. I talked to Home Depot; they did not have the answer. I called the repairman and he checked it out. He found nothing wrong. He did watch it washing and said he had never seen a washer tangle and twist clothes like this before, called Maytag. They said that I was loading clothes wrong, and nothing was wrong with the washer. They would not give me a number to call above them. This washer is bad. Maytag has known it for 4 years and done nothing about it. Ive been ripped off.

Maytag, Whirlpool, and Sears are junk dealers. We bought a Maytag Bravo topload washer in April 2011. Shortly after the first year, after using it once weekly, it began to stop draining. Clothes were soaked, meaning lots of wringing out by hand and using the dryer double time to get them dry. There are no clogs or kinks in the line. The machine is junk! It should have lasted much longer than this. I am not going to spend more money to have a repair person come and check on it. Its not worth it. Im going to buy a GE washer, the old-fashioned kind that gets clothes clean. Maytag, Whirlpool, and Sears are much worse-off breeds these days. They are off the list for good. Their products are a joke. Unfortunately, Im not laughing, but close to tears. Enjoy my money, you **.

Purchased a Maytag Electric range Model MER8800FZ2 in 2019. The surface Scratched the first week of purchase and the stains will not come off. When I called customer service they claim they are not responsible for cosmetics. In my opinion, This model was put together with the cheapest material they could find. Maytag is not what it used to be. The Elements take a long time to heat up. Inside the oven, the Glazed Paint is cheap product also where once it stains with food it never comes off.

I take pride in my cooking and love my kitchen. As you know this is where everyone gathers when you are entertaining. The Aqualift system does not work. I have run the process 3 to 4 times consecutively in row and the inside oven the oven is never clean. I wipe out the sides over and over. So disappointed. The only saving feature is that you can not see into the horrible look of the inside the oven when it is closed. Was this feature really tested before it went to market????

I am very pleased with the product, a perfect stove for cooking! It’s very easy to operate, easy to clean, multiple burners, excellent in cooking large meals, like soup, beef, Chicken and vegetable soup. It’s also very energy efficient, very safe to operate,

The machine had automatic fill which did not allow enough water to rinse the clothes properly. I had to run another cycle to rinse the clothes. The machine was also extremely loud. When I had a warranty repairman come out concerning these two item as it was brand new, I was told I should have researched better. I gave it away after 3 months.

Our Maytag dishwasher is a work horse. Never a problem just runs and runs. Could be a little quiet quieter. But does a t great job cleaning. I would definitely buy another one and would recommend it to any one.

We do not use the range daily. Our household consists of only two persons. First time we operated the self-cleaning feature on the oven the outer pane of the double glass pane door had what appeared to be grease stains and dirt. In as much as it is a SEALED double pane glass door there is no access to the outer pane to clean it. The double range was only 16 months old and was purchased at RC Willey in Henderson, NV. We also purchased ALL Maytag appliances for our kitchen i.e. refrigerator, dishwasher, microwave, washer and dryer on the same date. In addition we purchased furniture for the entire house at RC Willey. The Service Department at RC Willey advised me to access the Whirlpool website for assistance or to call an independent service repair contractor at my expense. THANKS MAYTAG! After having had your laundry appliances for over 30 years, without any service problems whatsoever, I was lulled in a false sense of security over the quality of your appliances. Now I have a household full of Maytag appliances and am at the mercy of independent service repair contractors.

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

We purchased a Maytag Top Load 5.4 cu ft efficiency washing machine. May 2019. It was making a funny noise already mid October and we had 8 parts replaced. After that it completely stopped working. We have been without a working washing machine for 2 months now. The technician has been to our house 4 times. When he came on Dec 31st to replace the mother board, that didnt solve the problem. He says the washing machine can not be repaired. We have been fighting with Maytag Canada and Lowes since the beginning of December. Neither company cares. We will never own another Maytag product. The company are crooks.

I purchased Model #MGR7661XB (Gas Cooktop and Oven) in November 2009. From the very beginning, we realized it was a mistake and looking back, we should have sent it back.The finish, both on the stove as well as the burner racks (the removable grate that the pan sits on when cooking) has some sort of coating that instead of repelling grease and food seems instead to actually attract it. Any hot liquid or grease actually seems to melt into the finish and becomes impossible to remove. Essentially, our stove was ruined within the first week. We have even tried putting a scouring pad on a wooden spoon and scrub with as much force as we can muster - to no effect. Short of using a putty knife, and completely destroying the finish, I cant think of any way to resolve it.As for Self-Cleaning ... yeah, right. Use for entertainment purposes only. It doesnt clean at all.The latest issue is now the oven lights about 20% of the time. The broiler still works and we have discovered that we can trick the stove by allowing the broiler to heat up the stove to about 200 degrees first - then, when the oven is already hot, the oven part will ignite.Speaking of igniting ... from the beginning, this stove has the loudest ignition system I have ever heard. You can hear it ignite click/pop from two rooms away and the oven cycles on/off every 10 min. or so. It is very annoying.All I can say is, never again will I buy another Maytag. This was supposed to be the upgraded sealed burner model (which also is impossible to clean). This stove is only 4 years old but it was a mistake from the beginning. Like I said, I should have returned it after the first week.

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

I purchased an expensive front-load washer and dryer a few years ago. About a year after I purchased the washer, there was a foul smell that developed. I contacted Maytag and they informed me of the directions to follow - keep the washer door open when not in use and use Affresh tablets periodically. I followed these directions and was unable to prevent the washer from developing mold in the washer. Id like to file a formal complaint on my washer and dryer. I want a refund on it. I paid way too much money on these units to suffer. Here are the details on my units: Maytag 5000 Series with steam 4.5 cu.ft., Maytag Commercial Technology, Model: MHWE550WW01, Serial: CS00202582, Type: 199-02 732 WT/CR, 12 amps, 120 volts, 60 hz.

Was very happy with choice when it arrived. Bought October of 2010. Now, this summer, nothing but problems. Honestly weekly cleaning of vents underneath, sheets of ice in freezer, refrigerator not staying cool, constant frost plugging areas, and no more ideas of how to make it work. I already quit with Kenmore after terrible problems with their appliances and now when Maytag doesnt stand up for years what are we supposed to buy? OUTRAGED with American quality of products and disposables. UGH!!!

My Maytag is 2 weeks old, and knew from the start I had a lemon. The compressor sounds like a giant freezer. I had the service man take a look at it, and while he was here the compressor did not come on. He pulled the plug from the fridge and turned it back on and still it did not turn on. I asked him to stay till it turned on and he said he could not stay any longer. I waited for him from 2 PM till 7:30 PM. He was to arrive between 3 and 6. Talk about frustration, and I only wish I had read all the reports before I bought this junker. I was so worried I decided to get the insurance for 4 years. The reason the ice forms is because you have no control over the ice. You cant see them and they get stuck. I had a side by side before this, and I can kick myself for not buying a side by side again. I was told to shut it it down when youve had enough ice cubes, to stop it from getting stuck. This ice maker is so big and so hard to pull out and the switch to turn it off is on the inside. So far my only complaint was the humming, but I can see a tough road ahead.

We purchased the Maytag Bravos XL MCT washer and dryer in July of 2013 and have been completely and totally dissatisfied with every use since. We immediately contacted the store where we purchased them and were told we had to contact Maytag. We contacted Maytag on numerous occasions only to be read ridiculous solutions from a notebook that were no different than the instructions in the users manual and never worked. We had our first set of washer (with agitator) and dryer for 23 wonderful years. The washer absolutely does not work. The decision to remove the agitator and reduce the water levels is absurd. The soap does not get distributed, the lack of water causes loads of clothes or sheets to get rolled up into tight balls with no hope of being cleaned, and the spin cycle is so powerful it rips your clothes apart unnecessarily. The dryer is smaller than the washer and cannot handle the same size load the washer can put out and typically requires more than one cycle to complete a drying. All in all this has been the most painful experience we have ever had with any appliance. We are completely dissatisfied with both the store where we purchased these units and the complete and total lack of response from Maytag after requesting either of them to take back these units or make some equitable adjustment so we could purchase different units. We have reached a point where we will most likely store these Maytag units in the garage and purchase a new washer and dryer, being forced to accept the financial loss.

Overall- I think washers aren’t made to last like they once were. Growing up- we had the same washing machine while living at home. It seems now- they only last 10 years if you are lucky. They should make more longer lasting machines.

I have a fairly new washer Maytag model #MHWE500VW serial #CSY0303991. I need Part # W10415587 doesnt excist for my washing machine anymore. Its been on backorder since Apr-May 2011. Maytag/GE insists that they are not responsible. As long as they can say backorder technically they are not liable for anything and dont really care that me the customer is having a problem and they Blatantly refuse to even investigate. I spoke with a GE supervisor just today and she basically told me wont help you because my appliance is out of warrenty. And she explained to my that my complaint will go into a file that no one will ever see. I searched the internet only to find hundred of other consumers are waiting for this same part. Ive called distributors & manufactuers. Same answer, backorder. My warrenty people are trying very hard to help me but again Maytag/GE refuse to help. Very dissappointed with this company. Wont be purchasing Maytag/GE products again. Wheres that guy in the commercial with nothing to do when you need him??

My new dishwasher had a defective board and worked erratically. Shortly after the warranty was up it stopped working completely. I contact both Maytag service and Home Depot on several occasions with no satisfaction. This a well known defect. Apparently the board replacement and service would cost in the range of $250-300. Too much for me as a senior on fixed income to justify. No dishwasher for almost a year. I then read an article indicating there was a class action settlement in California on the same make and model. I called Maytag again and after spending 2.5 hours on the phone I finally reach a person who sent out a service repair person. This person showed me a memo confirming the problem with the board. No recall but... if a customer is persistent they will give you the board. Finally new board installed at no charge.

My Maytag range from the 1990’s is the easiest to clean top of the range I have ever had. Controlling the temperature of cooking is very easy. The oven is not as responsive As it takes about 10 minutes to preheat. Once heated it maintains an even temperature.

I am extremely disappointed with Maytag and the representatives I spoke with this evening. One laughed after I told her I was 7 months pregnant and without a fridge for a week after owning it less than a year. I was repeatedly and curtly told, We dont cover that, when I asked only to replace the recent food I had purchased. After having to request a manager several times, I was put on the phone with Dana ID ** who said she would not be able to help with any food despite the delay of a week for repairs to our fridge. However, she could extend our warranty for 6 months.The only reason we were able to get someone out as early as we did was because we knew a licensed Maytag service repair company. Otherwise, we would still be waiting for someone to come out to tell us it would be another week before repairs. The originally assigned service repair company by Maytag did not return our call. There was no concern or empathy from the Maytag representatives that I was pregnant and could have eaten food that was not cooled to prevent bacteria growth that would harm me and my baby.Even their service repair technician recommended to contact them about the spoiled food since it was impossible for the repairs to be completed before the end of the week. We will never purchase Maytag again. The appliance failed with no warning in less than a year, and the representatives made no effort to resolve our issue of being without food for a week.

I have had my Maytag set for shy of 2 full years, of actual usage time, that is. My dryer seems to be functioning normally, minus an occasional lengthy cycle time, even after the clothes are dry. The washer however, is sitting in my garage now. F51 error code, which online told me the rotary position sensor was the issue. Yes, I was told by an A&E repairman, who was at the house for an unrelated repair, that it was the bearing that was bad. When he showed me what I was looking for, there was the bearing laying in the clear plastic housing, in the underside of the washer. Its going to cost around $350.00 to get the part, if it can be found, and the service call. No, not really worth wasting more money on it. I am very unsatisfied with this unit. With 4 kids and 2 adults at home, I expected much more from the Maytag name.

Im have finally given up and purchased a replacement for my Maytag Bravos XL Top Loading High Efficiency Washer! The Maytag was 2 years old and I have ALWAYS had trouble with it. My towels became sour after 1 or 2 uses (sometimes they smell sour even before use!). My dark clothes ALWAYS came out of the wash LOADED with lint. I researched online to determine whether these were common problems and found several sites with suggestions such as: dont use more than 1-2 spoons full of high efficiency detergent (which recommendation I followed), Use white vinegar or liquid fabric softener. (I tried both with only minimal results.) ALSO use a dryer sheet in the dryer (I did this but it seemed like a waste since I was already using fabric softener in the washer). Dont overload the washer. (I didnt, but if I couldnt fill it, then why did I buy a washer with such a large tub ?!) Clean the washer monthly. (I faithfully did so, and tried alternating Affresh and bleach to see if theres any difference in the result... not really. Make sure you are fully drying the towels (I ALWAYS DID!).We had a Sears repair technician come to the house the last time my frustration level was overflowing and she only made me feel like an idiot, repeating some of the above recommendations and insisting they would solve the problem -- which, if they had worked, would have precluded my need to call a repair technician!!! The repair technician provided no other service or ideas to fix the problems. My husband decided we should go back to the tried and true agitator-type washer... bye-bye, Maytag Bravos.

Maytag HE Top Load Washer - We bought our whole house lot of Maytag appliances 6 months prior to when we would need them, in Nov of 2015. There was a great Canadian Black Friday sale event special, so we purchased the whole lot at Home Depot thinking we had got a great deal, however back then there were very little reviews on the washers, as they were fairly new. This is the absolute worst washer, I have to pause the washer after the water level that the sensor allows finishes and add at least a bucket more of water to cover the clothes and clean them properly and rinse them twice to make sure the residue from the soap gets washed off (I use HE pods, so not using too much soap). Certainly not what you would expect when you buy a high-end appliance. Im going to replace it, but I cannot even try to recoup any money back, as I couldnt/ wouldnt be able to sell it to anyone knowing that it is just garbage!! You would think that a high-end appliance company like Maytag would admit that this appliance is a mistake and offer the consumers that purchased this junk a credit towards a washer that will do what is expected!! Think about it Maytag... you have lost a lot of future business by ignoring the fact that this machine is not what you advertise as a company that stands behind their name. I am sure to tell everyone that I know about the disappointment in this product. I have a friend that has a LG HE washer and it works great... so no excuses about water consumption regulations... its just not designed properly!!

We purchased this brand new Maytag dishwasher (Model MDB7749) from Home Depot July 30, 2013. Now a little more than 18 months after purchase the control panel is out. Some lights blink, several go on at the same time. Tried resetting by removing then reinserting power plug (that worked once before, a couple of months ago,) but nothing works. Pretty much the same defect and problem I am seeing with other folks with these Maytag dishwashers. I saw online that a Sears outlet was selling these same model Maytag units for 48% off...Well, now I know why. My older Maytag appliances lasted many years. My Maytag washing machine was replaced two years ago, and it had lasted 14 years. I guess they simply do not build them like they used to. I should of just bought a cheaper model for 3-400 bucks, would of got the same use out of it. Does anybody know of a brand and model dishwasher today that is reasonably priced, dependable and has some longevity to it? I will call for service on this, but Im not spending hundreds of dollars on a defective engineering flaw, throwing good money after bad. Besides, the repair would probably only give me a 30-90 day warranty anyway. Learned my lesson. I will never buy another Maytag product again...Ever. Also I see now that they are part of Whirlpool, so they are out too. Anybody have any suggestions on a good replacement unit? Thanks...

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

We purchased Bravos series Maytag washer and dryer. These are a match pair, the top loader, extra large capacity, very top of the line, $$$$$. The washer has already been replaced after many repairs, but the replacement new Maytag leaves a powdered gray residue on all the clothes because of the small amount of water it puts in the washer tub. Even on the deep water cycle, if I put in a blanket it will come out of the washer half dry where water has never reached it. This washer is the worst I have ever seen and cost top dollar. Maytag says nothing wrong but when I show them the powdered residue on the clothes they refuse to answer. This is the worst engineered washer ever, tangles the clothes terribly, does not clean the clothes and usually forces you to wash them twice to removed the soap residue left on them. I have tried every soap on the market, stacked clothing as Maytag suggested, tried various tricks Maytag has suggested, but nothing stops the grey soap residue. This washer cost almost a $1,000 for just the washer, it is a disaster. I have asked Maytag to refund my money but they refuse. If anyone else has their washer - we need to join in a class action lawsuit to force Whirlpool, maker of Maytag to replace this piece of garbage!!!

My Maytag refrigerator has driven us up the hill and back and has taken us several months in order for us to get the issue solved. This is quite an expensive fridge freezer and the after service has been diabolical to say the least. All their service calls in the UK were handled by a third party and it seems that there is some sort of change of ownership between Whirlpool and Hotpoint so after all the previous visits by different companies the problem of water leaking unto our floor is still going on and now all their call are being routed through a major insurance and a utility company who are more interested in trying to signing you up on one of their insurance policies than fixing it.To make matters worse the contractors they use are absolutely useless when it comes to fixing american style refrigerators. I was told I needed various parts which would have cost hundreds of pounds or that the appliance was uneconomical to repair. All of which was untrue. This I later found out when after emails after emails Whirlpool passed on the contact details of a service agent ags refrigeration who came out and found that there was a fault with the water in line connector at the bottom of the refrigerator which they replaced.

I bought the Maytag stainless steel refrigerator with the top double doors and bottom freezer. I paid $3000 for this thing and the ice maker has broken twice, an ice sheet forms on the bottom of the freezer and the drawers broke due to being cheaply made with plastic. I had the old style refrigerator for 15 years with not one problem. I think these newly made appliances are made crappy! Will never buy a Maytag again!!!!

I dont know anything about the Maytag washers and dryers but have a Maytag washer and dryer. And I just recently bought a house that the owner is leaving both the washer/dryer, and both are Neptunes. I have an older set of Maytag washer/dryer and they are about 20 yrs old. They are both top load and I had one repair where a water line had a small leak and the service man came and fixed it and havent had any problems since. So I came on Maytags site to see how good these are, but from what I read, I think I will give the set of Neptunes away and just keep my old set as I am told them will last a good 35 or more years. They are heavy duty and large capacity. Thank you for letting me comment on your washers and dryers.

Bought a stove in May of 2014. In July of 2014 we noticed a 1x6 stain inside the glass of the oven door. I called Maytag and they stated only 30 day warranty on cosmetic flaws. I said this was not there when we bought it. They asked if anything had boiled over because if liquids get in the vents on the oven door it can get in between the glass. I stated no, only cleaned with Stainless steel clear. They stated most likely when I sprayed the door it ran down in between the glass. I said that is a flaw. They said, no the vents are there to allow heat out. I asked if they also were designed to let liquids inside the glass, they said no, I said design flaw. They will do nothing. I also pointed out that nowhere in the owners manual is there a reference to this possibly happening. Our sons in laws have a 3 year old LG stainless steel with vents and have never had this problem. Maytag will not stand behind their products even when they are the ones at fault. Buy a different brand.

Purchased dishwasher Mod # MDB7749SBM1 thinking it was Maytag (lonely repairman) in June 2013 from Home Depot. Cost new over $1,000. As of March 2016, three service calls, two of which required replacement of the control panel. Now the control panel has failed a third time and we are told by Whirlpool (parent company of Maytag dishwashers) they will not cover the repair. They have offered a discount for a new dishwasher. Since that did not seem like a very good option to me, they offered to let me pay for current service plus a year for over $350.00. I was sad to discover that they are the manufacturer of most dishwashers available at your local home store dealer (Whirlpool, Maytag, KitchenAid, Jenn-Air, Roper, Amana). VERY DISSATISFIED CUSTOMER!!!

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

I purchased a Maytag MDBH979SAB0 dishwasher from Home Depot two weeks ago for around $600. I got it installed and it would not turn on. I contacted Maytag and after a few questions, she stated that they would have to send a repairman. After a few days, the repairman arrived and said hed never seen this model before but that we needed a new control panel. After waiting a week with no work, I called Maytag to get an update. The control panel is out of stock and could be a while - they are trying to find one somewhere around the country. They refused to send a replacement dishwasher, even though this was brand new. Their policy says repair, not replace. Dont take the chance purchasing a Maytag dishwasher.

Fridge model mff2055drm00 - Purchased 2 years ago. Upon delivery and working water leaked from bottom. Called recommended service. Result took out fridge and brought in another new one. Today the fridge/freezer ices up, ends up sounding like a rocket ship. Not working efficiently. Called for authorized service. Was told needed a new thermostat... after TWO Years? Service call price $125, quote to purchase, replace and install thermostat $550. Almost $700. Big mistake buying Maytag- who knew? But never again! We are quite angry and very disappointed with the mediocre performance of this product.

We bought a Maytag 2000 Series machine about 2 years ago. At first the machine worked great, as a new machine should. Then, after about 7 months water started pouring out of the top dispenser for detergent. I read the manual and looked online at the Maytag website for common problems. It said that sometimes small clothing gets sucked through the hose and needs to be unclogged. I followed the instructions to fix the problem. It worked fine for about 2 weeks later during the middle of a load the machine would stop and give me error codes. I looked these codes up and now I have another clog on the drain tube that needs to be fixed. Lo and behold these 2 problems have been continuing ever since. I cannot do a load of laundry without getting a code and having to take the machine apart. I called Maytag to explain my situation and the customer service representative said that because I fixed the problem myself at this point there is nothing that can be done. They do not guarantee that their equipment will work nor will they help solve the problem. I cannot believe that we spent so much money on something that I cant use. Not to mention the fact that when I do complete a load some of the clothes are ruined by the machine ripping holes in them. I would not recommend buying a Maytag because they dont care about customer satisfaction or the quality of machines they sell.

My husband and I bought a Maytag 3000 series front-loading washer in 2009. In either December of 2014 or January of 2015 it broke down. We had a repairman come out. The inner and outer tubs and a bearing needed replacing. He said it would be expensive and some of the parts were no longer available. In his opinion he hated these new machines as they were nothing but problems. Next we contacted our dealer whom we bought it from. He contacted Maytag himself, then he gave us telephone number to speak with. He no longer carries this brand because of problems and said our washer was no longer made because of problems. So we call, spoke with several supervisors in customer experience. They offered half off another washer of similar value on Maytag or whirlpool brand. Maybe Im being difficult but I didnt plan on buying a new washer after 5 1/2 years. When I and my husband ask to speak to next person in chain of command we were told there wasnt one. Really!!! She would not pass us to a higher authority. She read a classic... Im sorry for your experience. Were offering you a great deal considering your warranty was out. Im hoping this will keep anyone else from this Bad experience.

My dishwasher like many others have mentioned is experiencing the same control panel issues. When I set it to Wash, it spontaneously goes to Rinse Only. I am unsure exactly the age, but given the number of complaints Ive read, with the same problem, it seems as though, there was a flaw many years ago in design and regardless of issues hasnt been resolved with the newer models either. I realize appliances dont last forever, but Maytag was always known for the lonely repairmen and Id hoped the brand would continue to live up to its advertising, despite being purchased by Whirlpool.

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

Washer goes off-balance even when clothes are evenly distributed in tub. When it is turned off to rearrange clothes (which may have to be performed a couple of times), washer goes back to starting cycle which means more water. Afraid to do laundry unattended.

My Neptune dryer purchased in November 2005 had the drum crack at about three years old. I complained so much that they finally agreed to send a replacement drum for free. Now, two years later, the drum has cracked again and tore through the housing on the front of the dryer. The repairman said it would be too expensive to repair. Consumers, beware.

I bought my Maytag Neptune washer and dryer in 08 or 09, and it has smelled like mold and mildew for years but I still have to use it because I cant afford to get a new one. I cant get the smell out. Also, I have to take the pump apart at least once a year due to the fact that sometimes, no matter how you check your pockets, change still gets left behind and they dont make a screen or filter that will keep the change out of the pump. It is not hard to do, but the first year I had it, it were in the service center as much as it was home. I was glad when someone told me what was happening because I fix it myself in like 15 minutes and move on. But it should come with a self service manual showing how to do this procedure to save people money.

Since the day the Neptune washer and dryer were installed, the washer has given me nothing but problems. It vibrates so badly and dances all over the floor.I have had the repairman over at least seven times and, now, it is out of warranty so I am spending my own money. The last service man was from Hurst Appliances in Regina, SK. He removed the pedestal to see if this might be the problem. He also sold me some foot pads for $50 that he said might help the problem. However the machine is still vibrating and the terrible mold smell comes out of it as well. I am thoroughly disappointed in this product. I will never buy another Maytag product and tell my friends not to as well.

I’ve had my electric glass top range for four years. Normal use. I set the temperature to 425 degrees to bake a potato. At the 225 degree mark, the oven bursts into flames. The fire burned itself out in about a minute. I turned the oven off and immediately went to google to see happened. I’m pissed! This stove is only four years old!

Bravos XL washing machine is the worst washer I have ever used. IT DOESNT GET THE CLOTHES CLEAN! There is not enough water when filling up, and you cant control it. I put a load of dog blankets in the washer and at the end, they were in the same order as I put them in; they hadnt moved! All the stains were still there and there was soap scum everywhere. Also, while I appreciate a large drum, it is so large that I cant even reach down to get the clothes on the bottom, I have to use a stick to get them up. I am so irritated that I spent $1636 for the washer and dryer (dryer works fine but same trouble with the huge drum). I got mine from Sears online after checking the Consumer Reports which put it in the top 5 washers!!! Dont buy this washer. Waste of money. Will probably just have to throw it out and its brand new.

Maytag washer Bravos MCT. Let me tell you your guidelines do not help at all. Would someone please tell me how to get my laundry clean when it doesnt even get all the clothes wet? Looks like Ill have to go to the laundromat at least I can get my clothes wet. You should be ashamed to put out such an inferior product. Worst washer ever.

The Maytag Bravo is a big waste of money. Get a less expensive machine. You will have no problems and save money. This is my experience: SETTINGSYou cannot control the settings completely. Every setting is preset. For example, if you choose the Bulky setting, you cannot choose the water save spray rinse. Those two cannot be selected together. Certain settings can only be selected with certain temperatures. This will however be the least of your problems. WASHINGIt does not get clothes clean. I have had instances of items coming out with still stuff stuck to them, not just stains, but actual solid material stuck to it. My cat threw up in his bed and when I got it out, it still had small pieces of vomit stuck to it. I have always only used the Bulky setting which fills up the whole drum, so there is sufficient water to wash. I cannot imagine what it would be like if I used the Normal setting. Many times I had to wash thing twice. If you use the normal setting, you will get hardly any water. It will be a moist bundle of clothes moving like a big lump. You need water and some degree of friction to eliminate the dirt. SPINNINGIt is constantly stopping, beeping and showing me the UL sign (uneven load). You have to unravel the items and reposition them Around the drum. If you are an old lady like me, this is a real chore because the items are now soaking wet and very heavy. Also, because there is no agitator, the items come out in knots (tied to one another) and you have to separate them. DURABILITYThe lid is loose. It looks like it may be missing a screw on one side. It still locks, but it moves sideways when you close it and open it. BOTTOM LINEThe whole thing is a disaster. Get an old fashion type. It will work better and you can save your money. I honestly think there should be a class action suit against Maytag.

Have owned Maytags (washer and dryers) for 40 years. I bought a Bravos top load washer and matching dryer because we gave our old set to a daughter leaving for college. That was less than four years ago! We bought this because it conserved water and there would only be my husband and myself home. So laundry needs would be minimal. The washer quit draining and starting making a terrible noise several days ago. Immediately called repair service - I knew from the onset this was going to be a big problem because when I told them the model, they responded - uh oh! Two days later service man comes to assess repair and lifts machine up and tells me bad seal has leaked to gear box and ruined it. Soooo for a machine that is less than 4 years old, I will have to pay $280 for part, $79 for service call, $60 for labor and $35 to have them pick it up and redeliver (because the repair is too big to be made in my home). $454 for a machine that gets minimal use!!!! I can add another $100 plus and buy a brand new machine. Why should I have to??? In doing some research, I found out this is a common issue with this model and Maytag has paid for the repair of other washers because it is a common problem. Even the serviceman said that and recommended I get a hold of Maytag. Their response - sorry mam you dont gave an extended warranty. (NOW I HAVE A LEMON!) Guess my next step is to write a letter to Maytag Corporate Office. I will keep going up the ladder until they address this flawed machine problem! One thing is for certain - I will never ever buy another Maytag product of any kind or will I ever recommend it. They are just not reliable. Guess, nowadays they are considered throw away products - keep them a few years and throw them away because its not worth your money and effort to repair them :-(

I purchased a Maytag electric range model # MER8775AS in Feb 2012. While boiling syrup, the pan overflowed onto the oven door. As I began to clean up the spill I noticed that some of the spill had gotten inside the door on the inside of the oven glass. To remove the stain would require disassembly of the door. I called Maytag and complained of what I called a design flaw and they said, No, its your fault for spills entering the door. They even sent a condescending email to me informing me that if I needed to purchase parts, where I could get them. I designed appliances for years and this is another example of poor quality and lack of consumer service. I AM DONE WITH MAYTAG.

Washer broke down after one year. The washer stop in the spin cycle. Called many times - got no satisfaction. Still using local laundry mat. Very disappointed. Always thought Maytag was top of the line. I guess I was wrong.

Maytag Front load washer mah8700aww - This washer has been the biggest boat anchor of a machine. Nothing but trouble and bad parts. New motor after 18 months, water level sensor at 2 years, main control board twice now at 2 years and 4 years, and now it is showing signs of needing yet another main board. E3 trouble code plagues our home and basement. This machine has been leveled and re-leveled numerous times and still shakes like crazy... I mix my paint cans by setting them on the top... the best use for this machine. Yes it sits on a concrete floor. So not satisfied and will not ever buy another Maytag anything. There should be a negative star rating. It does not deserve even 1 star after being taken advantage of like we and thousands of others have been.

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

Would give them 0 Stars if that was an option. Bought a Maytag washer and dryer in Aug 2021. Washer broke Jan 6 2022. Called Maytag/Whirlpool on Jan 6 as it was still under warranty. They only had one service company in our area to work on the washer. I called them and it took them 10 days to come see what is wrong. Ordered parts. Said it would be 2 weeks. We are now 6 weeks into this with no parts. Called customer service and they said they were notified that their service company needed a part and would take another 21 days to resolve. Talked to a supervisor (Demetrius) who sounded like he did NOT want to be in that position. Offered no solution other than we will just have to wait. Threw a 3 month extension for the warranty on which still does not fix the problem. Sad to see this company go down the tubes as it was once a pretty decent business with solid products. No longer.

Purchased a Maytag refrigerator on 08/15/13 model #M1TXEGMYQ01. Started having cold problems 06/15/15, called company. 1 yr warranty expired 08/15/14,had to replace a 22-month ref on 07/15/15. Prior I owned a Hotpoint that lasted for 17 yrs and the last one was a GE that lasted for 18 years.

We went to Home Depot and bought a Maytag front load dishwasher and dryer and microwave 3-1/2 years ago. The washer and dryer were put in right away. The dishwasher and microwave stayed in their box for another year due to us remodelling the house room by room and the kitchen wasn’t done for a year. We put the appliances in and the dishwasher panel went out in October 2011. The washer in April 2012 started having a failure 8 when it gets to the last spin and rinse in which takes a lot of shuffling clothes to get it to finish its cycle. Then last night, May 14th, 2012, the microwave caught fire and all I was doing was brew tea in a glass Pyrex measuring cup not to mention the fan didnt work from day one. The whole house was full of smoke and it melted the plastic. So the most I got out of 3 of these products is 3 years at the most. This is very sad that we spent this much money and it lasted less than 5 years. I am writing this to warn consumers not to buy Maytag appliances. They should last longer than 3 years and are not cheap to buy. This makes me very angry and I hope someone takes this seriously and work on the problems before someone burns up due to these appliances catching fire. Our dishwasher had a recall shortly after we installed it due to the element catching fire and we had your repair man replace it.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

I am so fed up with my Bravos XL washing machine, that I felt compelled to vent and see if others have the same issue. The first two reviews I read complain of the same thing as I am finding. Some kind of scummy residue on my dark clothes, need to rinse, sometimes soak again to get the residue off. Have tried many different detergents. The guy at the store said try cold water! Yeah right. I use half the amount recommended. We have two boys who play baseball. The seller said this would be a great machine. Id almost consider trying to sell it on Craigslist and buy a good used one with an agitator. Spent a lot of money on a fancy looking machine. Definitely overpriced and overrated. Do not buy this machine!

In May of 2009, my husband and I bought a new Maytag refrigerator side-by-side, model MSD-2572VEW. The day we bought it, pieces started breaking. The shelves started cracking, and now they are completely falling apart. There are also cracks in the inside walls of the refrigerator. Every single door shelf, inside shelf and wall is falling apart. I have fixed the ice-maker myself several times. I am now going to design and build some new shelves so that we can get as much use out if it as possible before it is unusable. I am angry that a company can make such a horrible product and not have to take responsibility. If my employer ever provided a client anything but the best, we would all be out a job.

I bought this washer brand new in 2011 for $650. I had bought a Maytag washer before in 1967 and it was still running in 1995 when I gave it away. Considering my first Maytag lasted me nearly 30 years (Last I heard the machine was still running in 2005), I never thought my new Maytag would give me any problems, until it was at least 10 years old. (I did know Maytag had been bought by Whirlpool but didnt expect any difference in quality). Boy, was I wrong! After using it for a month the machine broke down and it had to have the clutch and gear box replaced. Last week July 2016 the machine broke down again. It was the internal computer (referred to as the electric control unit) a printed circuit board that retails for approximately $300 (A ridiculous price given that much more complicated laptop and tablet computers today can be brought for $100, the circuit board should retail for no more than $40).With labor the repair bill came to $550, which was nearly as much as a new machine and did not justify the cost. Supposedly the electric control is susceptible to current surges and power outages. Given that this is the case, it makes no sense whatsoever that a machine billed as eco-friendly would carry a part that will doom it to the junk pile because of a power surge or outage and does not carry a surge protector. After learning of my experience Maytag called me the next day and offered to sell me a new Maytag at a discount price, which of course I flat-out refused.I would never ever again own a Maytag appliance or one made by its new owner (as of 2005) Whirlpool. With such susceptible electric units these appliances will sooner or later result in electric fires that will end the life of its owners. The US govt needs to protect US citizens from these predatory companies that make over-prized, throwaway products labeled as eco-friendly that are potentially dangerous. My advice for anyone that is thinking of buying a Whirlpool or Maytag washer dont do it. For those that already own these machines do not run them without a heavy duty surge protectors. It is not worth your life.

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

I am angry that Maytag puts out a washer that hasnt been through quality control. The computer panel is a piece of **, and is not worth $1.00. Do not buy this washer. Shame on Maytag.

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

Maytag Bravos 300 Electric Dryer - Purchased dryer 2011 and a computer part went out and Maytag wants $418.66 for a computer part. This dryer was used only 6 months a year. Poor attitude about repairing from Maytag and they would not do anything to make us happy with product. A dryer that goes out in 3 years is robbery. Maytag should repair and make customers happy but they just dont care. Anyone who buys a Maytag or Whirlpool product should have their heads examined. I tried to talk sense to Maytag representative but to no avail. I am now going to make sure all of southern Indiana knows of my problem with this product. Those who know me know I have the ability to contact thousands of southern Indiana and Louisville residents.

Within the first year of having this washer (Maytag Bravos X series) the cam broke in it. And then about two months after the warranty went out, the motor quit. It wouldnt spin my clothes at all and would never get my clothes clean. I was having to hand wash my clothes just to get them clean. Not a very happy person, I live paycheck to paycheck and cant afford rock continuously pay to have my washer fixed.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

Purchased a Maytag MSD2553WEW00 refrigerator on 2/27/2011 from Home Depot. Began using it in July 2012 upon completion of home construction. In February 2014, after less than two years of service, the refrigerator was running but no longer cooling. After the expense of several part replacements and a service call, it was determined that the compressor had failed. Unlike most manufacturers, Maytag did not warrant the compressor and closed system beyond 12 months. The refrigerator looks like new but the cost of repair is prohibitive relative to purchasing another new refrigerator. Maytag was contacted but was not helpful.

My Maytag dishwasher is very easy to use. Saves on money and time. I enjoy it and it have made my life so much easier. When you cook for two you can be out the kitchen in no time.

I purchased a Bravo Washer and Dryer from Home Depot. The Maytag Bravo washer and dryer we purchased from Home Depot did not work from the beginning. Before I called Maytag, I tried for several months to redo the way I was loading the washer and dryer.I tried several different settings however, the clothing keeps coming out smelling like it is still worn. Spots are in the clothing that normally comes out with a washing (with my prior washer). The clothing just does not get cleaned and it gets so tangled that it has ruined some of my clothing. There is clumping of the detergent, even though not a lot has been used.I had the repair company come out three times for both the washer and the dryer. They have checked and no errors codes where found. One gentleman told me again to redo the way I load the washer and the dryer. I have done it so many times, but I tried again and even purchased little dryer balls. It made no difference.I called Maytag again and was told they would have to have another company come in and do a second opinion. The person came and said that he agreed that the washer should be able to wash and the dryer should be working correctly. He recommended that a possible problem with the motherboard for the dryer (which was a possible problem mentioned by visit #2) could be handled, but he had to have it approved. He would check with the company and get back to me. I received a call the next day and a message was left telling me there is nothing he can do with the washer. He was told by Maytag/Whirlpool that I should only fill the tub lightly and not pack it down (I told everyone how I load and I never pack my clothing down). The washer should, when loaded with wet clothing, be only 1/3 to full otherwise it decreases the wash ability dramatically.The problem of the siphoning action for the softener section of the washer should be handled by running boiling water through the tube to loosen up the wax portion of the softener. The possible correction for the dryer exchanging the motherboard (it could be set incorrectly) was turned down by saying that the dryer is running to Maytag/Whirlpool’s satisfaction and nothing else would be done, since there are no error codes for both washer and dryer.My towels have a mildew odor to them when they are used. They have to be washed twice and run through the dryer a long time before I can put them away. I purchased a high capacity washer and dryer and I am told now not to fill it more then 1/2 full. That is not what I was told by the person selling it. Otherwise, I would not have purchased this set at all.

Just replaced a washer that lasted over 7 years thru 3 renters with the Bravos top loading washer. There is nothing efficient about a cycle to take 73 mins to wash 20 articles of clothing (t-shirts, socks and underwear). The machine dont wash the top of the load. Also the deep clean feature isnt deep cleaning. I recorded a video of 20 mins of the machine not washing properly before going into rinse cycle. If this item dont produce refunds of the amount of water wasted RE-WASHING and electricity because it doesnt clean on first wash, then its time for Maytag to pay my utilities. For the money spent on the machine, going to the laundromat every other week with 1 roll of quarters each trip comes to be I can wash for 4 years and will outlast the longevity of the machine before it breaks! Also bulky mode is how you get more water in the machine but will take 63 mins to wash.

Quiet, efficient and leave you with clean dishes & utensils at the end of its multicycle cycle. This unit can self-clean and is always beautiful with its shine finish stainless steel interior. This unit can be installed by any user as it comes with everything one will need to complete the installation.

I am very frustrated and disappointed with all of the appliances I purchased from Maytag, 3 1/2 years ago. The stove has never cooked evenly, and they replaced both heating elements, and it still does not bake properly. I just called customer service, because my pies for the holidays burned once again. They told me there was nothing they could do. I cannot believe a customer that spent this much money with Maytag (purchased a washer, dryer, microwave and oven), gets no help from the company. The transmission has been replaced in the washer, and is still noisy. The dryer is also very noisy. The stove does not bake properly, and the microwave quit within a few months of purchasing. The quality of Maytag is very poor, and the customer service is obviously poor too, when they said there is nothing they can do for me. I guess they do not care about customer loyalty.

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

Purchased a new set of Maytag Bravos appliances in 2010. Washer lasted 3 years -- had a failed bearing and repairman said not worth fixing as tub would most likely also need to be replaced. Replaced with a new Speed Queen which has been operating trouble-free. Today dryer quit heating -- repair person stated it needs a new board -- not worth it to me. I am off to now purchase a new Speed Queen dryer. What happened to Maytag quality???

I bought a Maytag Bravos washer in March 2015. Over the summer I had two items, both cotton t-shirts come out of the washer badly stretched and torn. Other items have come out badly stretched, but not destroyed. After the second shirt was destroyed, I called Maytag (Sept. 2015). A young man was sent over. He ran the diagnostic, finding nothing wrong. He did not check the agitator. He reported back that it must be the way I loaded the machine. I use the Normal and Active Wear settings, leaving the center clear. My loads are very small. Under these conditions items should not get caught. Maytag stands by their claim that it is my fault. I only figured out what was actually happening when I saw an item caught.

DO NOT BUY A MAYTAG BRAVOS MCT WASHING MACHINE!!! I have had the machine for two and half weeks, it HAS NOT WORKED EVEN ONCE!!! Service was scheduled - again for a BRAND NEW machine - through Maytag/Whirlpool - and the service ordered never happened. We waited an entire day, 8 am - 4 pm, only to discover the service desk of Maytag doesnt work either. My service is now booked for another week away and I am working on returning this AWFUL Maytag washing machine which never worked even one time!!! Warning: Do not buy Maytag/Whirlpool appliances!!

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

We purchased a Maytag bottom-freezer refrigerator MBL2258XES1 from Home Depot on 12/30/2011. Other than being a bit noisy, it functioned without problem for a little over two years after which we noticed water pooling on the floor, just below the left-front corner of the bottom-freezer door. It was shortly thereafter we noticed the large sheet of ice that covered the entire floor of the freezer. Over the past several months I pull out the large towel, my spatula, my meat tenderizer and break up and lift out the ice onto the towel around every two weeks. Thanks Whirlpool/Maytag! At least that Maytag repairman isnt lonely anymore.UPDATED ON 03/18/2015: I called Maytag Customer Service, (800) 344-1274 to discuss remedies for my Maytag/Whirlpool bottom-freezer refrigerator which has a perpetual layer of ice on the floor of the freezer which leaks onto my floor. I was offered a product called Repair Plus One which includes parts and service for this repair and they throw in a 1-year warranty. The cost: $359.95. The representative informed me I only had 24 hours to make up my mind as the offer was time limited. I asked if there were any other remedies available to me and she said none other than a service call.

This review is pretty simple, if you have kids, do not buy this washer! I just went to the local wholesale guy after almost 8 months of using this POS, and spent $200 on a older agitator machine, after the first load my 7 year old close came clean of dirt! There is literally no water and the motion of the drum, it is almost impossible for this machine to clean clothes. I really am surprised that no one has started a class action. And to anyone saying the are hog farmers and work outside and get dirty? I would love to see it first hand. I am going to post on YouTube and show what this machine really does. Think about this before you buy, We all get hooked on how big it is, thinking you can do 4 loads at once, but trust me the low water thing is real! How do you clean clothes with no water! You will regret this purchase. And I am a Maytager for life! So disappointing.

Maytag french door bottom freezer model #MFF2558VEB5 - It stinks to read all the similar problems Ive had with my unit. Purchased Nov 2011. Problems started within a year. First minor, deli drawer broke. I use clear duck tape to operate it and that has been fine. But not acceptable. About a year ago the water leak out of bottom freezer was noticed. The bottom inside is frozen sheet. I break up and manually remove quite often. NOTE: I intentionally do not use, did not install, the ice maker - historically they are poor risk so I dont bother. The ice unit is in the machine but not installed. I assume my water build up which freezes on bottom related to poor design of defrost drain and that is supported by other comments here. I find it disgusting. Live and learn. Its B.S.

I bought a Maytag dishwasher to match other appliances in kitchen. Work great, not loud and gets dishes clean. Have owned it for 10 years and have one problem with the door latch. But it was easy and inexpensive to replace.

Our control panel just went out...purchased in November 2015. From reading reviews it appears our only option is to purchase a new control panel and hope for another two years. Ours (MDB7749SBM3 Dishwasher) was purchased from Sears and was not cheap. When is Maytag going to recall this panel? I read reviews that this problem goes back to 2011.

Bought the top load water saving washer 3 years ago and paid around $500 dollars for it. It will not operate correctly. I always thought Maytag was the best!! My main complaint is I cannot get no one on the phone to ask questions about what might be wrong with it!! Now Im angry, its like you buy it, its yours, we arent worried about you after that!! I am on a fixed income and no one cares!! Ill never buy anything manufactured by Maytag ever again!!

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

Weve had our Maytag dishwasher for less than 4 years when the control panel quit. The repairman came today. He was here 10 minutes and it cost us half as much as a new dishwasher. Its just the two of us and we use the dishwasher once every 4-5 days. Almost laughed when the repairman said the part and labor was under warranty for 90 days! There is no quality control anymore. Just greed.

It took about a year for the problem, which turns out to be an extremely common problem, to start. The build up of water in the freezer due to the clogging drain. Maytag needs to step up for the consumers that purchased their defective product. I have cleared the ice and tried to clear the drain three times only to have the problem return. I refuse to pay someone $300 or more to repair this. This is crazy and unfair!

Bravos XL was costly. Mistake! I owned my first Maytag for 20 plus years. The sticker shock of buying a new Maytag 4 years ago was pushed aside knowing how long my previous model lasted. The salesperson at Lowes closed the deal with his explanation of an improved gear driven system vs the old belt and pulley version. Oh how wrong! I too have the jet plane from hell landing in my home for over 2 years now everytime the spin cycle engages. This is a two person family and it failed at 2 years?!?!?As for water conservation... if I dont include the additional rinse cycle, my clothes dont get clean. Watched the YouTube on how to repair this unit... but what guarantee do I have that it wont go back to the same problem in another year? Cant afford another big investment like this now that I am retired, so I will run this baby until it seizes up. Dont wash clothes if company is coming or if you want to enjoy evening TV programs. Not sure why this unit hasnt been recalled based on all the complaints I have read on this site?? Worst decision I ever made! I bet the Maytag Repairman is spinning in his grave!

The Maytag dishwasher works really well. Not the quietest, but cleans thoroughly. I dont use heated drying though, to save energy. Stainless steel interior retains enough heat to mostly dry. However, unit died after only 7 years. Expected longer life.

I bought Washer and Dryer Pair new less than 2 years ago. Within 6 months of purchase, the bearing went - warranty. Then 1 week before one year old, bearing went again. I contacted Maytag. They told me it was my problem and I should have bought extended warranty. Lemon law should apply and I asked about appeal process and was told that there is no such thing. Now, the washer is needing a new pump and it is not even 2 years old!

Refrigerator 1F122269VEM7 not making ice, shelves broke, freezer drawers stuck, and motor running like an automobile. Refrigerator only 2 years old. Paid 4000 dollars and this is not acceptable. Reviews online very disappointing. Other reviews on this product not good. People having all kinds of products with not resolve.