Two in a row make it just over a year then the control panel goes out. You call a Maytag repairman and they say the control panel is bad! #1 it should last more than a year and a half. #2 a part shouldnt cost you as much as the darn dishwasher! Do not recommend nor would I ever buy another Maytag.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

On March 2011, I purchased a Maytag dishwasher model #MDB7749AWB1. The dishwasher worked excellent for 16 months. One morning, with dishes loaded and ready to go, the start button would not light up. The other buttons did light up but that did me no good, I need the start button. A few days later, none of the buttons would light up. I found a repair person who said it would cost over $200.00 to make repairs. I refuse to put another penny with no guarantee that this new part would work. I will never ever buy another Maytag appliance. The last inexpensive, unknown manufacturers dishwasher lasted me 13 years. Do not waste your money on this thing.

I purchased a Maytag Bravo washer 2 years ago and it is the worst washer I have ever used. My clothes are never clean. It is always out of balance and is so slow and takes forever to do a load of laundry. It has started stopping on spin and have to unplug it to get it started back then it sounds like a jet coming in for a landing and has to restart the spin about 3 or 4 times before it ever finishes. I have had the repairman to look at it and says there is not anything wrong with it, but something has to be wrong for it to stop on spin and have to unplug it for 5 mins. in order for it to reset itself and start again.

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

I bought a Maytag Centennial Commercial washer, 3.8 cubic feet, Model # MVWC425BW on September 17, 2014. My clothes were never clean and barely wet. The machine took almost 2 hours to do a load of clothes and they werent even clean! I bought the 3-year extended warranty through Lowe’s. Three years and 8 days later the machine stopped working. Serviceman came out and told me the washer was fatally wounded. He said the transmission failed. He also told me the replacement part would be $400.00 and that it wasnt worth it. He said these machines are junk and Maytag has had all kinds of issues with them. So Maytag knows these machines fail and yet do nothing for their consumers. Maytag, you will only ride on your name for so long; consumers are catching on. Maybe back in my Moms day you were the go-to brand but Im afraid that ship has sailed. Ive always gone with Maytag but now I question that choice. I came on Consumer Affairs page to see what brand I could buy other than Maytag. Seems Kenmore gets high marks.

This one of the worst purchases I have ever made! Paid over $850 in March, 2015 for the Maytag Bravos XL. At first, we experienced leaking and now there is a terrible banging and clanging noise! Had an appliance repairman come to see what was going on. Apparently it needs a hub replacement and bearing replacement. Was told by two companies that it is not cost effective to fix it due to the amount of parts and labor.Aside from this major issue, I never felt that the clothes came out clean. Many times, the clothes would come out with detergent all stuck to the clothes and had to be rewashed. The softener and bleach dispensers are not removable and it is nearly impossible to get all the way into the cup in order to clean the mildew that builds up. The fabric softener dispenser always had gummed up chunks.Called Maytag several times to no avail. Was basically told - too bad its out of warranty. I have never heard of a washer giving out after 3 years! The worst part is that I have searched many places on the Internet and apparently the bearing problem seems to be a common issue with this washer. I purposely bought an American made product and am extremely disappointed in not only this product, but the company as a whole. The customer service department is awful. I will NEVER purchase Maytag or Whirlpool ever again. They lost my business for putting a terrible product on the market and refusing to acknowledge flaws. Interesting that this model is now discontinued, but they refuse to acknowledge the problems. Stay away from Maytag and/or Whirlpool!

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

This dishwasher works great with regular plates and glasses but not so well with my plastic bowls or cups. Im trying different detergents to see if it makes a difference on how clean the dishes are when done.

I bought the Maytag Bravos because I was told it was top of the line and expected that Maytags reputation for quality would provide me with many years of dependable service without problem. Boy, was I taken for a ride! Unless you have a lot of money to spend, DO NOT buy a Maytag Bravos washing machine. After only 3.5 years of normal use (3-4 standard loads per week) and doing everything as suggested by the owners manual, my machine has developed a bad drum bearing. The cost to repair this bearing is $400 for parts and $200 for labor. In other words, I am forced to buy a new machine after ONLY 3.5 years of use. When I called Maytag customer service department to question them about my problem, their response was there are no recalls on your machine, so we cannot do anything for you. When I further questioned them about the lack of quality/dependability my machine provided, they again said, Sorry, the machine is out of the warranty period. Thank you for buying Maytag. If you buy one of these washing machines, you better have the extra money to buy an extended warranty.

Worst washing machine!!! I purchased the top loader Maytag Bravos washer HE in 2011 and they are the worst!!! It has been repaired three times already and now is making such a loud noise and I have been told it is the bearings. I did purchase the extended warranty and it expired. The reason I did not get a renewal is Maytag & Home Depot do not allow the the extended warranty company to let you know the warranty is ending. So now I have a 3 1/2 year old washer that needs bearings and will cost $500 + for repairs. Will not be spending anymore money on this absolute piece of junk. I had a Maytag that was 22 years old that I replaced and thought I was buying the same quality but never again another Maytag. This company may want to employ only repairmen because you will need only them because no one should buy a new one going forward.

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

It leaves white stuff all over everything. You have to rewash or rinse black clothes at least twice. We have to clean the washer frequently or the clothes smell like mildew. I chose Maytag because I thought they were the best. Apparently, I was wrong and it was a mistake buying this.

Purchased a new Maytag washer top load/Dryer set on April 1, 2016. Having trouble uploading receipt but I paid 1,145.83 for set. It took 2 weeks to get it delivered on April 15. 1st use it shook and wobbled even though the load was balanced but Ive read that is a problem with these machines. 1st load of clothes, washer didnt fill with enough water to wash properly - 3-4 inches of water for a full load of jeans. Top 2/3 of clothes hardly got wet! Changed the setting, same problem. Changed the setting again, same problem. I had to stand at washing machine and keep lifting the lid to get more water in the machine. Clothes didnt rotate in machine so all the clothes on top half didnt get cleaned. The spin cycle is scary! You could hear clunking noises and it had nothing to do with load being balanced. Did a small load and same thing with water level and spin cycle. Called Home Depot to pick up both machines on next business day. The dryer lint trap is so long, it made a mess trying to remove the lint even after only 1 load. NEVER AGAIN MAYTAG! Ive never regretted an appliance purchase like I do now. Maytag and April Fools day are a perfect match. Only its for real and not a joke.

I have never liked the stove because it is too small (it came with the triplex) and it has porcelain like top. One burner burns to hot, the other three mediocre, there isnt enough space between the burners and the back of the stove. It doesnt cook evenly and it really does not have a low or simmering setting. You cant set a timer for simmering because it cooks too fast. The knobs are stuck and sometimes wont light when you turn them down. The oven is okay, but could be better. Wish it had self cleaning. The broiler in no existence. Food way too close to the flames. We have had this oven since we bought the triplex back in 2011.

This washer is no better than a glorified garbage can. Maytag AKA Whirlpool should be ashamed to put their name on this product. Like others before me on this website my washing machine sounds like a jet is taking off in my basement. When I contacted a serviceman, he told me the drum seal is broken and the bearings are shot. I have the machine since April 11, 2011. Not even three years to date! I do not have an extended warranty so shame on me to believe that a 900.00 machine should last well beyond 3 years. Unfortunately, I am getting the run around from Whirlpool as all of you have experienced. This is criminal. Not only are we as consumers being defrauded by irresponsible manufacturing but these huge hunks of metal and plastic are polluting our environment. Our parents had washing machines and dryers for as long as 20 to 25 years and they actually cleaned clothes. We now have high efficiency machines that destroy our clothing and leave them dirty and wrinkled. They are now made to break in 5 years and from what I see on this website the average for breakdown is becoming 3 years. Do you think that this is not by design? The service call turns out to be more than the value of the machine, so the repairman doesnt even profit as consumers refrain from costly repair and repurchase. The only profitability is gained by the manufacturers that keep pushing out junk to the consumer. These manufacturers should be accountable like the American auto-manufacturers became accountable for the junk they manufactured at the expense of a whole city, Detroit.

I purchased a Maytag Centennial washer a few years ago. In my opinion it hasnt worked properly from the start. We went on the low end of price, because we spent a small fortune for GE products that broke after a year and a half. This Maytag hasnt been a much better experience. First it didnt drain and spin clothes, and I was told I was using too much soap. Cut back on the soap and it started working better and going through the full cycle but the clothes never felt or smelled fresh and clean. Now 2 1/2 years in, it doesnt complete the full cycle on its own, AND there is dirt in my washer after every load. My clothes come out with streaks of dirt on them. The picture below is of a pillow case I just took out of the wash! Ive cleaned the washer multiple times, but it doesnt drain properly so it doesnt help. Maytag charges a service fee just to come out and troubleshoot and charges you again to come and do the repair. Im running out of reputable companies these days with washers.

I bought a Maytag washer and dryer at Lowe's when I bought my home-the price was great and I have not been disappointed in them-have had them over 3 years now. My washer has a stainless steel tup and is a top loader. The combo of the two was less than $1,000. The washing machine has deep clean, heavy load or light load, hot, warm or cool water settings, a hand wash setting and many other features that I think most consumers can appreciate.

The steam/heat produced by the oven has made the electronic (digital) control panel buckle. Yes! This is a thousand-dollar (plus) stove, and it has warped, through no fault of mine. When I want to cook something, I press the keypad to enter the number of cooking degrees that I want. The problem is, the control board is not working correctly. Regardless of my typing in 350, it will default to 100 degrees and stay at 100.As a teacher, I do not have a huge income. I was disgusted with my recent repair estimate of $80 for a service call, and a quote of over $600 for the replacement part, plus some not-yet-determined labor installation costs. Calling the 800 phone number for Maytag connected me to some local people working as independent and overpriced contractors in Los Angeles, California. They are not MAYTAG employees, so they are not well-informed about the product.I miss the time when manufacturers stood by their products, and had factory-trained and authorized employees available to make repairs. I bought this monster Maytag stove from Lowes. I am disgusted with both companies. I have gone online to research buying my own part and hiring a local yokel to put it in. Most everyone I have encountered has been a rip-off artist. I am teaching your kids and grand kids to read and write, and you dont want to help me repair my stove without price-gouging. I can use the burners to some stove-top cooking. Life has become a hassle without being able to cook.

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

After 16 months my Maytag dishwasher control panel went bad. The company told me they could not help me. I asked for a new control panel to install myself, no luck. I bit the bullet and bought one online for 110 dollars. 2 months later... you guessed it, its bad. Now I have to send it back under warranty. It was a Maytag name brand OEM part. I thought Maytag was a reliable name, I thought wrong. Never again.

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

Great appearance, great job on getting our clothes clean and dry. Good dryer cycle choices and output. Good washer cycle choices and output 98% of the time, BUT, sometimes the washer needs a do over about once in 50 loads. Overall, two thumbs UP.

I purchased my Bravos washer in 2011. Three days before the warranty was up, the motor went out. It was leaking oil and had to be replaced. Two days later it quit working again I had to have another repairman out and found that the gear shifter had popped off so he put it back on and charged us 85.00. Luckily my husband watched him repair it and knew what to do if it happened again, which it does just about every 2 or 3 loads so I have to pull it out and pop the ring back on. I waste more water than I save with this machine. I have to drain the water so I can move the machine out and start all over because they didnt wash, and that wastes more soap. I would get laundry done cleaner and faster if I beat it against a rock. This is the worst washing machine I have ever owned and I will never buy a high efficiency washer or another Maytag again.

Control panel is defective on my Maytag dishwasher. Found a phone number that was created to deal with this problem. I only had to hold for a few minutes but the first person I spoke to was rude and unhelpful so I asked to speak to someone else. When another agent came on the line I told her that only the normal and rinse button light up but do nothing when pressed. She arranged for a repairman to come to my house and determine if my control panel is defective at their cost. When he arrived he asked me what the problem was and I said, The touch pad control panel is not working. He stated, Your control panel needs to be replaced. I have to order the part and come back to fix it. He was there for about five minutes and he never laid a finger on the dishwasher. When I asked if the control panel design has been fixed he said, No, you will probably have to replace it again.There is a video on the internet that shows how to seal the electronics with silicone. The repairman said that they cannot seal the electronics unless Whirlpool provides a kit to do it. I guess the Maytag repairmen may have to come out of retirement. My husband will seal ours after it is replaced so we hopefully dont have to deal with this problem again. So now I am waiting to see if he returns in a reasonable time frame and gets my dishwasher going. There is a class action suit about this issue filed in 2013 about this defect.Updated on 09/23/2015: A repairman came to my home on August 20, 2015, at Whirlpools cost, and he determined my touch pad did not work. He informed me that Maytag would provide the part, free of charge, but it would cost me 85.00 for them to come back and install it in 2-3 days. As of today I am still waiting for the part to come in, apparently due to high demand Maytag was out of touch pads, which were out of stock. No idea of when that would be, the repairmans company said, dont call us, we will call you when the part arrives. So I began to look for the part myself, found a couple on an auction site, but most companies that sold parts were on backorder. Until I found a company that said their inventory was out of stock but they had five, stashed in the back. The price of 105.00 was not that much more than the 85.00 cost for the service call. Got it in two (2) days, installed (in about five minutes), sealed by my husband and I loaded it and washed my dishes. I was so overcome with relief, tears came to my eyes and I almost fell out. I give five star to the fella that had the part stashed until I needed it.The Maytag repairman is still waiting for the part so he can fix my dishwasher.

2013 We purchased from Lowes Maytag washer and dryer front load stackable. We live in a house 1890. We have a closet that these units go into so we are restricted to what brand we can buy. WE read the reviews. People must lie or are paid to write good ones. Within a few weeks the washer was giving us trouble. The door latch was not closing properly and it would take up to 20-30 min. to get it to start. Called and they said the latch was stuck. Again started having problems on and off. Months went by and had another service call. Same issue. Fixed it again. 2014 again same problem. We have to order a new latch and some other part. They could not get the part. Called Maytag directly and they were back ordered. What does that tell you. This is a major problem so much so that no one anywhere had the parts. 6 wks to finally get it and got it fixed. But in the meantime, the dryer was not working correctly. The clothes were damp and lint was all over. It was like a steam bath. They came out and when they looked at the back of the dryer it was burnt. Now this is what upset me. He said it could have caught fire and burnt down our house. Nice. The dryer was shot. They said to fix it would cost more than it was worth. Our warranty gave us a new dryer. 3 wks later I have my washer and dryer back working. In the meantime we have spent more time at the laundromat than at home. Brand new washer and dryer and are going to the laundromat. We had the dryer 5 days before it stopped working. Brand new dryer. Called and got a service call. The spring on the start button was not correctly put in. Who inspects these products. This was not right from the factory. So they fix it. Said if it happened again they would need to replace the entire thing. I do not know what that means. That was Dec. End of Dec. the washing machine is not running through the cycle. It had weird display on the washer. Thought maybe it was overloaded. Had to cancel and drain and then hit drain and spin. This takes not only more time but more electricity. I put in 2 sheets and it did it again. Had a few loads that ran properly and again it started. Called for service. He comes out and the motor that runs the belt to spin and some circuit board is shot. They call 2 days later and say that no parts can be found anywhere. WTH! It is 18 mos old and already the parts are extinct. So the warranty company said it was not worth fixing. They are giving us a new washer.I remember the commercials about Maytag that the repairmen had nothing to do. Well I thought it was because they did not break down. No... they cannot find parts. This is unacceptable. We have to go through the inconvenience of them not working and schlepping to the laundromat baskets of clothes. In the winter this is not fun. We are retired. Have to walk down icy steps. I have a washer/dryer upstairs and I cannot use them. Dont work. Not just the aggravation of dealing with repairs but not getting parts available, then having to wait to get money back to order a new washer and dryer and then get the dryer and 5 days later it doesnt work. Now we have to wait 2 wks for a new washer. It better work. Have to buy the warranty over again on each product cause they fulfill it when they buy you a new product. So this costs us extra money. The money we pay at the laundromat. The cost of electricity every time we have to run the washer 3-4 times to get it to spin out the water so I can dry them.To say I am upset is an understatement. I was told by a rep at Lowes, well Maytag has about 3 lemons a yr and you just got all of them. That was their consolation to our problem. I think Maytag needs to inspect their product. Our house could have burnt down. It is not a matter of parts going bad but damn the stuff is not even 2 yrs old. And the dryer was 5 days old when it stopped working. WE had a Maytag dishwasher and it was installed brand new and did not work. It had a defect in it. I never got to wash one dish in it and it had to be repaired. So I am not happy with Maytag. You go on Facebook and tell your story and all the Maytag horror stories come out. You need to do something to save yourself. Your company name is going down the tubes. Thought you should know this.

I bought a Maytag washing machine, model number MHW6630HW2 in January 2021. It works fine on ordinary loads, but it cannot spin the water out of bulky items, not on any setting. I put my machine-washable winter coat in the washer and it left it full of water. I re-tried on 4 different settings, and though the washer spins, it cant spin out the water. I went to the Maytag support site. The sites said my model doesnt exist. The phone number for support does not allow you to get any support other than a service call. The Chat option doesnt give a lot of support either. They said that if I call for a service appointment and the service technician finds that the machine does do a spin cycle, then the appointment is not covered under warranty.

Maytag washer not draining properly. Called Aug 15 for help. First tech in on August 23, makes a diagnosis, orders part; no news, I call, am given Sep 15 as next date. Come 9/15, I take off from work, only to find out tech cannot come that day, to reschedule. Next tech comes 9/25 with a different diagnosis and different part to order. By October 3, an announcement that part came in, to make an appointment. By now, its been a month and a half, I am so angry. I call a friend, who fixes it in 15 minutes by simply clearing a clogged drain filter. This is unacceptable: the inordinate wait, incompetent techs, unresponsiveness from customer service. I cancelled my contract with Maytag Warranty/AIG.

I was repairing this Maytag Maxima washer and was almost electrocuted. I simply grabbed the wrong screws which were too long for the door switch, one screw went through into the open/close switch and contacted voltage, thus causing a direct short to the chassis and me. It also damaged my control board (the most expensive one in the industry), now Im out an extra $220 because Whirlpool made an engineering error. A screw should not be located so close (millimeters) to a voltage source where a simple mindless mistake could cause electrocution and possibly death. As for the washers operation, the drain pump failed after just two years, it sometimes leaks water out the front because debris gets into the boot drain back holes. It smells like mildew even though we leave the door open, my clothes stink, Affresh is costly and really doesnt help much. It does a decent job of cleaning, not as good as the old top loaders but it saves water. I think next tax return time this machine goes up for sale and we get a better machine.

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

Maytag Bravos XL washer and dryer. Best washer and dryer I have ever owned. I have owned about every major brand and these are by far the best. My husband is a hog farmer and the washer does a great job. I will always purchase Maytag appliances.

This is in reference to Maytag washer MVW7232HW0 that broke after 5 months. Maytag sent a technician out who claimed we needed to replace 3 parts. We waited almost a month for the parts to come in just to have the technician say that didnt fix the problem. We have been waiting a 1.5 months for a resolution with nothing in sight. Now we have to either way another TWO months for another part, buy a new washer and get refunded for the old one (but WE would be responsible for the almost $300 price difference it now is), or wait for a new washer to come in stock and Maytag will replace it. However according to them there are no washers in stock for the foreseeable future. This company has been a joke to deal with. I have everything recorded and will take this further.

Bought my Maytag washer and dryer as a set in Feb 2011...like many, I did not get the extended warranty, as I thought this was a great brand. Ive had nothing but problems with both. The dryer takes two rounds to dry, the lint filter is wet and rusted. The belt has popped off and needed to be put back on..The washer does not clean very well. Ive replaced the shift actuator because it was not spinning, now it sounds like a turbo jet taking off. And as of a week ago, my washer started leaking underneath. Paid a tech to come look at it and said my motor was done and Im better off buying a new washer and even recommended that I do Not buy Maytag! So I googled Maytag Bravos and seen all the poor reviews and realized I wasnt the only one! My set is 3 years old and its ridiculous that Ive had these issues, as so many has. Extremely disappointed of this brand and I too, will not be buying Maytag ever again!!

My over-stove microwave is approximately 18 months old. Suddenly, the fan came on and will not turn off. I had to unplug the microwave. This appliance is out of warranty but certainly should last longer than 18 months. I feel that Maytag should certainly be called to task for selling and promoting such a shoddy, unreliable product.

Bought a French door Maytag with freezer on the bottom. Ice build up on the bottom of the freezer and it has ruined my floor. We are replacing the floor in the kitchen. It is only a few years old. They have horrible customer service and will not replace anything.

I purchased an Atlantis washer in 2005 and assumed that Maytag was still one of the better manufacturers. How naive of me! What genius at Maytag thought it was a good idea to place the water filter inside the washer? Not only can you not keep the filter clean so that cold water will flow properly, even worse, if the filter completely clogs, the water will not stop filling into the tub which could, of course cause an overfill and flood. I narrowly escaped this scenario once. No one should have to stand and watch their machine fill with water to insure it stops. Now the machine is causing a grinding noise when agitating. I expect it to stop working any day. I will not buy another Maytag or Whirlpool, who of course now owns Maytag. And I will not pay another repair bill for the filter or any other part. The brand was once considered the best in America, now its just another brand thats a piece of junk produced in another country.

Bought all stainless steel Maytag appliances when we remodeled our kitchen in 2010. French door fridge freezer broke down three times. First the fridge lost its temp and we lost our food. The freezer went into overdrive and froze the vodka solid. Second time massive ice build up in bottom of freezer so we had to constantly chip it away to keep door closed. Third time was a repeat of the fridge not working at all and the freezer going insanely cold. Sad to say, we have given up and bought another fridge freezer for $1,500, not a Maytag!On to the washing machine: a super duper top of the line expensive Maytag. At the end of last year it started to make disturbing jet engine noises in spin mode. It for worse and worse so I had a repair man come and take a look at it. He said it would cost over $700 to fix. Once again, we decided to cut our loses and buy another washing machine. I have saved all the paperwork including the repair bills for both appliances so Im good to go on the class action lawsuit.

I bought this large capacity top loading wash machine about 22 years ago and it has yet to fail me. It had never needed any repairs and cleans my clothes wonderfully. The brands reputation is well earned. Great washer!

We have a Maytag washer. It is the noisiest washer I have ever seen! It is in the garage as you could not have this washer in a house. The deep water wash is not deep enough. It bangs and knocks VERY loud! There have been times when all of the clothes are not even wet.

Bought the Model MZD2766GEW and the MSD2454GRW side by side models of the Maytag side by side and the wide side by side from Home Depot in the year 2002 replacement appliances after a fire. For both units I paid $2526.92 dollars plus tax to put one in my kitchen and one in my basement. I was told by a plumber Maytag was the best, buy Maytag. It seems like from day one things went wrong. The ice maker kept building ice in the bottom of both freezers. The ice maker never worked right and would build up so much ice in the dispensing area, you would open the door and ice would fall all over the floor and you would have to take a knife to the shoot of the ice maker to unclog it. The drawers would freeze, the vegetables and anything in them, you had to keep the refrigerator temp to Zero and things would still freeze. Water eventually would leak all over the floor and I couldnt figure out where it was coming from. The freezers on the left but then water seem to be running to the right and out the refrigerator part. I couldnt afford to call anybody and the warranty was running out. I had 2 year parts and one year labor but at the time couldnt afford the service call charge. Eventually I was sent a recall notice for a compressor or such. I thought, Hurray, It will be fixed. Not at all. He replaced both those parts on both refrigerators and after he left it started leaking again. I called Maytag and they said, did he replace the part that was recalled? I said yes and they said They were not obligated to pay for anything past the recall. I should call and have the units serviced by a technician at my cost. If he says its the recall piece again, to call them back. Again I had no money to call a technician right away but when I did, he came to the house, told me it wasnt the recall and claimed to fix some kind of defrost sensor which cost $180.00 for the parts plus labor, plus service call and this had been a different technician than the first. He left and the problem continued to leak, freeze etc. In fact it seemed worse. I gave up calling and decided to deal with it hoping one day to replace but money problems happen and it is now 2014 I never could afford new refrigerators and have had to put up with the leak for all these years and continue to pick up and replace soaked towels everyday. In 2005 I disabled the ice maker which helped when I opened the door since ice doesnt fall out but both Refrigerators continue to make thick sheets of ice on the bottom and food is frozen into it so I cant use the bottom and when the buildup gets so bad it takes 2 days to defrost by shutting the entire unit off. All I can do is put my food in one freezer and refrigerator while the other defrosts. I also have turned the downstairs one off completely. Now as a second refrigerator I just dont trust keeping it on leaking also. I bought these units after a whole house fire and the last thing I want is another fire because Maytag just doesnt care but I cant afford new Refrigerators because these repairman and Maytag cant figure out whats wrong and fix the problem with this dangerous feature and I call it that because it seems to come with most of their units from when I bought the unit till now.12 years later people are still having the same problem with the same and copy cat units. Maytag, a plea goes out to you to recall and repair these units. The original recall did not work and like me a lot of people need to be redeemed for what you left go on and a lot of repairmen are ripping off people calling this problem what its not and stealing our money when you know what the problem is and can fix it. My plea is recall this problem or be responsible before God or who you believe in for letting it go on so long and the damage it may cost people. Maytag, people use to love you but youve ripped our hearts out and it will cost you in the long run.

Front load washer unit does not respond to control inputs. I have called Maytag service and support. One can find a repair or maintenance manual. Im in a smaller market so there is limited service. Maytag service and online support is terrible. Maytag stores are fronts for independent service companies. Its probably okay, but misleading. Everyone wants to order the main controller board. It would be good to have a maintenance manual.

Angie from WFCC-PREFERRED APPLIANCE REPAIR had the wiring harness delivered to her personal address and then came out and installed it that same afternoon past 5pm to ensure I had a working stove. She explained what had happened with the parts delivery mixups and also delivered a $100 gift card. Very happy to have my range working and all has turned out well. I am a long time Maytag customer and its great to have all my appliances back.

This washer came with the home we recently purchased. I used the machine and OMG the spin cycle is NOT quiet.. I posted a video of it on FB. A friend of mine who owns and operates an appliance center watched it.. messaged me back and said Do not call repair man as it is cheaper to buy a new machine... I knew this machine sounded like a piece of **.. I know I wont replace with the same machine.

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

Low water level resulting in poor cleaning. Very poor design. Requires 2 rinses so the water savings of the wash cycle is a joke! Im very disappointed with the so-called Maytag quality. If doing very very small or handwash loads it work somewhat ok! Would never buy Maytag again!!

Purchased 6 11 21 from Menards. $1100.00. With extended warranty $134.99. Lid lock inoperative on 9 11 21. Called Menards, past 30 days. They will not help. Called Maytag, took 2 weeks to get a diagnosis on issue, while technician was there week of 28th the motherboard fired. Another month, part came in October 23rd then wiring harness fired, and pump also. 1 week for parts, which were replaced, Technician came and was stumped as it still doesnt work. Diagnosis after this appointment for the pump replacement is clutch, rotor & stator are fried.Nov 18th, new rotor came in and Technician says although brand new in box, it is defective from factory. New one ordered. In meantime I have called maytag every week with no results, they tried to get me to accept 100.00 gift card, I laughed, as we are a family of 6 and generally have 6-8 loads a week. And have spent on average 70.00 a week for the last 14 weeks, we could have bought another washer by now. Last maytag lasted 16 years! This one 3 months...They finally decided to replace it, but we wont recieved it for another 4-5 weeks. So, 20 - 22 weeks of no brand new washer bought in good faith, brand rep, and paid for based on prior experience. So far, No customer service, No brand reputation, No product longevity. I will never buy another maytag, ever. If you only had negative stars to award this useless product. This is almost criminal, and is close to being fraudulent and willfully deceitful. It is false advertising and to date they have not really stood behind their product...

Model# MVWB850WQ0, Serial# CY4070329, Type 580-02. Bought this Commercial Technology washer 2-1/2 years ago thinking the commercial model would be heavy duty. It was only heavy on the wallet. The washer started to emit a loud roaring sound two weeks ago that never happened before. It happens on spin cycle. We cant even have a normal conversation in the house. After reading similar problems and outrageous cost to repair, Im leaning to look for a replacement without the Maytag label. My 10+ year old Sears Kenmore didnt have any problems. My mistake was to replace it with a more efficient washer. I guess New+Efficient doesnt equal long lasting for Maytag. You would think a major manufacturer would put in heavy duty bearings in a washing machine. Heck, maybe the bearings are heavy duty but design shortens bearing life. Enough time spent on Maytag. Stay away!

This Bravos top load was supposed to be energy efficient but after leaking and getting a repair estimate ($79) the technician informed me that the ring and putter tub (all cheap plastic) had several large holes in thin caused by an uneven load. Total cost of repair was $517 for a $900 washer after 3 years. He suggested that the Maytag was junk and that I buy a speed queen...LOL. When I called Maytag of course they lied and said they were not aware of any problems and would not help with the cost of repairs. Can everyone say Class Action Lawsuit...Shame on Maytag! DO NOT BUY THIS washing machine!

Why is no one doing anything about the crappy product that Maytag is putting out. I am a single mom of 4 and I had to purchase a new refrigerator about 3 years ago. Spent a lot of money on this Maytag, approx. $1400 and it is now useless. I had nothing but issues with it from the time I got it. The bottom freezer kept icing up and then leaking all over my kitchen floor. I had to call a repair guy out, who charged arm and a leg and said it was fixed and 3 months later it was doing the same thing. Since I could not afford to pay ridiculous amount of money to repair it again (although I question what they said they fixed), I had to chop up the ice each month and take huge pieces outside and i had to keep towels always at the bottom of my fridge (yes very attractive) but it ruined my floor and carpet. Now all of a sudden the piece of junk just shut off and stopped working and keeps making this popping noise. Lights went out in front panel. So I had to call a service guy out again but this time I called an independent local guy that is not gonna rape you in charges like Maytag does and he told me to look into this that he has heard so many complaints that the front board with control button has been known to blow out the back circuit board, which is what happened. He told me that parts are MDs, so he would have to get another manufacturer and he heard that even with replacing both of them, it has been known to not work and Maytag takes NO responsibility at all for any of this. THIS IS WRONG. I cant afford to spend around $800 to now fix this or another $1,400 to buy a new one. So I am without a refrigerator. What a nightmare. MAYTAG, TAKE RESPONSIBILITY FOR YOUR CRAPPY PRODUCT. We are hard working people that spend our money and expect a good product. I also have an oven I bought and I can tell you it is a piece of crap too. I swear at it all of the time, as it takes forever to cook anything and the outside that is supposed to be stainless steel is all yoked up. It is like a tin can, looks horrible. I will never ever buy another Maytag product and I hope that ConsumerAffairs steps in and does something about this.

I have had this washer just a little over a year and the sensor panel went out... For $600.00 it should not break right after the warranty goes out. Buyer Beware.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

We bought a washer & dryer from Home Depot 2 1/2 years ago. The control board went out on my washer. I called Maytag and they wanted $109 for a diagnostic fee and wouldnt tell me how much the labor would be. A control board costs $350. So by the time all is said and done... the money would be better spent buying a new one. Maytags slogan of dependability lasts is a bunch of hooey. Washers should last more than 2 1/2 years and Maytag should back up their appliances. They just lost a customer.

I purchased high end Maytag washer, dryer, dishwasher and microwave in May 2010. On Saturday 4/25/14, the Maytag Microwave stopped heating. The fan runs, the panel, display, lights, clock, and tray all work. It just doesnt cook. The Microwave was installed in June of 2010. Not even 4 years old. I have tried to troubleshoot via the instructions that came with the microwave, i.e. Check the demo mode is not on. Dont know why after 3 yrs it would be, but checked it. No help. Pulled the plug out and replaced; turned breaker on and off; checked to see if its was locked. Nothing. I then checked the door and I found that the plastic inside panel on the latching side of the door is pulling away from the door itself, which is part of the locking system. The magnetron shouldnt work if the door system isnt closing properly. The latch system is what is causing the door to pull apart. I am wondering now how much microwave exposure my family has been getting from a malfunctioning door? I have had a Microwave, dishwasher and refrigerator made by Maytag in the past. The refrigerator is 14 yrs old and still works fine. The microwave and dishwasher were at least 10 yrs old when I replaced them with the new Maytags I have now. Here is the problem. Maytag is not Maytag Corp. anymore. Whirlpool Corp now owns the Maytag brand. Prior to the old Maytags I had, I had GE fridge which was junk, and Whirlpool, dishwasher, stove and microwave. They were also junk. I swore I would never buy Whirlpool products again. Surprise.

Purchased new Neptune stacks in 2002 and had several service calls on our expense and we noticed the hinges on the washer door were rusting! Ordered new ones from dealer but rust continues and has spread to top of machine over the bleach dispenser. The metal is falling off! Bad rust on the inside lip under door also. I contacted Maytag when I first noticed rust and they blew me off so I contacted the local dealer we bought from and they did nothing to help. Will never buy Maytag again and have not recommended it to anyone else either. ModelINGooZES. Serial: 51867064AJ.

I have been on the chatline with Maytag customer service for two days, trying to enforce my warranty, which expires next week. My washer flooded my kitchen over the weekend, and I contacted Maytag to schedule the repair under the warranty. First, the woman, Aisha, looked up my registration, and confirmed that I was who I said I was, that my address and phone number had not changed, and told me that according to the records, the washer was purchased on 2/7/2011. Whats the problem? First, they wanted the model and serial numbers. I realized that this is important information in determining what machine needs what repairs, except there was not one sticker anywhere on my washer! Aisha said that the technician would not perform the repair, if the manufacturer did not install the model information properly on the machine. As if I had any control over the placement, or lack thereof, of proper ID for the washer. This was followed by a request for proof of purchase. I explained that I moved, and misplaced it, but I would have it emailed to me from the original purchaser. I was told that unless she could verify the proof of purchase, and the date of purchase, she could not schedule the repair under the warranty. This is despite the fact that not 5 minutes ago, she had just read this information from her computer! I asked her why would I register someone elses washer under my name and address? She didnt care. I told her I would have the receipt emailed the next day, and she stated that regardless of the date I requested, and scheduled the repair, if the actual repair took place after the expiration date of the warranty, it still would not be covered! I told her that makes no sense. I have no control over your scheduling issues. If you cant honor the warranty if the repair is made after the expiration date, then I need a date prior to that. I am entitled to the terms of the warranty, and intend to use them. Aisha said again that, without proper proof of purchase and purchase date, without proper tags on the washer, and if the repair takes after the expiration date, it would not be covered. I disconnected from her, and reconnected with another rep, who told me that some of the information Aisha gave was incorrect. I can schedule the repair, get the receipt and email it, or submit it through the chat, and regardless of when the repair was actually done, the warranty would still be honored. This person couldnt be sure what effect the lack of proper tags would have on that. My third re-entry into the chat was no better. I located a copy of the receipt in my email, and contacted the chat again. An almost amazing thing happened! This woman again confirmed all of the information Aisha recited last night, and was prepared to schedule the repair, without even asking about proof of purchase. This woman, Jennifer, was willing to schedule the repair, verify that it would be covered under the warranty, even if it was after the expiration date, because I had called and arranged the appointment before the expiration date, and she was willing to have the missing manufacture tags replaced. I had to ask her three times to review the email, and confirm that I had the correct receipt for the technician. I asked if the technician in the course of repairing the washer, had to remove the drainage hose, could he either replace it with a longer one, or add an extension, because according to Lowes at the time of installation, the hose they installed was supplied by the manufacturer, not them. Jennifer stated that since he was only there to repair the leak, and installation is not covered under the warranty, I would have to pay for him to replace the wrong hose, with the correct hose myself, even if he removes it! I told her that she needed to ensure that the technician absolutely did not remove the drainage hose from the back of the washer during his repair, because if he removes a part that is obviously the wrong part, and then replaces the wrong part after his repair, I would file a complaint every single place I possibly could. Why would a repair technician remove a part, determine that it is the wrong part, and then put it back! That is like a mechanic repairing the axle of a car, and discovering the brakes are bad, but since he is only there to repair the axle, he replaces the bad brakes after fixing the axle! He was going to be able to replace the missing manufacturer tags, though! This entire process took at least 3 hours and two days. To date, Maytag/Whirlpool is absolutely the worst company I have had to deal with, right after Sears, and ahead of AT&T. The consequences are that so far, Maytag refuses to have the technician replace the wrong hose with the correct hose, if he removes it in the course of repairing my washer.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

Why are the clothes in my dryer getting stuck in Maytag Neptune? It seems there is a little opening around the rim of the barrel in the back of my dryer that drawstrings, zippers or similar small parts of the clothes can get stuck in. It twists the clothes around and is ruining clothes, also is making a thump-thump sound. Someone, please help!

I am very frustrated and disappointed with all of the appliances I purchased from Maytag, 3 1/2 years ago. The stove has never cooked evenly, and they replaced both heating elements, and it still does not bake properly. I just called customer service, because my pies for the holidays burned once again. They told me there was nothing they could do. I cannot believe a customer that spent this much money with Maytag (purchased a washer, dryer, microwave and oven), gets no help from the company. The transmission has been replaced in the washer, and is still noisy. The dryer is also very noisy. The stove does not bake properly, and the microwave quit within a few months of purchasing. The quality of Maytag is very poor, and the customer service is obviously poor too, when they said there is nothing they can do for me. I guess they do not care about customer loyalty.

I purchase this dryer not even a year ago. It is not performing right. I call customer support and they willing to try something to see the problem. I hope I don’t have to pay anything out my pocket.

Had some extra time, so I thought Id add my .02 to those including myself disgusted with Maytag products! 1st up, the Maytag washer and dryer I purchased from my nephew after his divorce. The washer shot craps 2 months after I bought it from him (out of warranty of course!). The transmission went out - cost to repair $550.00. My nephew paid $350.00 new at Sears. We happened to have our ol reliable clanking GE, so we used that while deciding what to do about the washer. In the meantime, the dryer quit heating. Cost to replace heating element - 400 smackers! Dryer new at Sears was $250.00.Come to find out that even though they had Maytag names on the washer/dryer, they were cheap copies by White/Westinghouse. Well anyway we bought a set of Whirlpool Duets before doing our homework, cuz if we knew what was gonna happen... Before we knew the trouble we were going to have with the washer/dryer, we got a Maytag Quiet Series 300 dishwasher (Maytag Quiet Series 300 MDBTT60AWW). Yip, the control panel failing problem! Only purchased 1 so far (only 1?!), but my wife likes to hand wash the dishes. If we were the typical family using the dishwasher all the time, I would have replaced more than 1 at a cost of $135.00 each from Sears and doing my own R&R work, saving on the labor. Cost new at Lowes - $350.00Up next is the Maytag fridge. I purchased it back when our 2 boys were at home. I bought it mainly for the name and large capacity. After about a year (yip out of warranty) the cooling was very uneven. Sometimes the freezer would defrost by itself, then it would start working ok again. The top couple of racks in the fridge would be quite a bit warmer than the bottom. I understood the top racks would be a little warmer, but Im talking like 15 degrees. I called a repairman and told him about the problem. He said hes received numerous complaints on this particular fridge, and theres really no way to repair it unless the electronics are replaced as well as the compressor because as the compressor gets weak over time, the electronics get fouled up by this. Cost new - $1300.00. Estimate over the phone cost to repair - $950.00 with no guarantees. Replaced with a SamsungAs far as the Duets? No problems so far. They work great and we are very pleased by them. But I have did my research and am holding my breath! I also have a Maytag microwave thats still working, but has did a couple of unusual things - the lights in the front panel display started flashing showing a fault. I unplugged it when its did this to reset it. That was a while back and now it seems ok. At least for now!When someone says, Yeah, well, you might just have a lemon, but the rest of Maytags appliances are fantastic! My wife and I when we hear this are ready for a fight! Weve had experience with all of Maytags products, and with the exception of the Duets (so far), they are nothing but junk!! Another thing I wish to mention is the Samsung fridge. Its about the only model that has a factory 5-year warranty on the compressor and major components. Weve had several fridges in our married life, and the Samsung is far superior to any fridge weve owned. Ill be looking to that brand in the future. The last item I promise: If you read the reviews on front load washers, none of them get very good ratings. If I would have know that, I may have purchased a top load. But the Duet washer does do a superior job (IMO) cleaning the clothes, and the clothes are virtually dry after the last spin.

Is there any place to give a zero to this Maytag Front Load Washing Machine Model MHW5500FW1 and if there is a class action lawsuit please include us! We have owned other Maytag Washing Machines and never experienced such an epic failure as we have with this washing machine! We were so excited when we purchased our new Maytag washer/dryer set in March of 2018 we even remodeled our pantry/laundry room to accommodate them! As the chief operator of the washing machine, I have literally cried at what a mistake weve made! We have no complaint of the Maytag dryer. Let me describe my new normal procedure for laundering a load of clothes. First, load the washer with clothes then press power/cancel then press rapid wash let the clothes get HOPEFULLY saturated with water then hit hold to start and then hit power/cancel this shuts off the washing machine. I then press power/cancel again and select normal and the water empties out of the washing machine from the prior load and then starts to refill, if the add a garment light comes on (when it wants too) and no I dont change any pre-set settings I am able to add extra water with a pitcher, if this procedure works I let the washer run its 1-hour and 48-minute cycle. If not, I have to start over again because the add garment light wouldnt come on to allow the door to unlock. After the clothes are finished I again press power/cancel then hit rapid wash put my fabric softener in the dispenser press hold to start and let it run its 36-minute cycle making sure my clothes are rinsed appropriately and not stiff because of the lack of water. I neglected to say that when Ive tried tricking the washer and think I am able to add extra water, if Ive added too much the sensing kicks in and the washing machine drains all the water out on its own and refills with the little water it allows! Which is maddening! I throw up my hands and sit down and cry!!! I have contacted Maytag/Whirlpool complaining about the lack of water and their wacky water sensor! I asked them how can you conserve water and electricity when you have to wash your clothes over and over with long wash cycles? This doesnt make sense! My white clothes are now dingy and stiff as well as the colored. Maytag says you can use powdered detergents if its HE High Efficiency powdered detergents, but thats not true. The detergent doesnt dissolve and ends up on the clothes at the end of the long wash cycle because of the lack of water! From the beginning I adjusted the amount of powdered detergent for the front load washer and have to dissolve it in hot water prior to washing and hopefully am able to add it to the clothes if the add a garment will let me! I have now resorted to extra cycles to rinse out any remaining detergent hoping my clothes will be soft and fresh smelling. I had planned to replace my old Maytag agitator washing machine with this piece of junk front loader, fortunately we kept our old washing machine as a back up!

We bought top load washer model # MVWC425BW1 at Lowes brand new 9/22/14 for $493.93. On 11/23/2017 it stopped working and would not even come on after lid locked. Found out it needed new parts that would cost us over $300 to fix and we could buy another new washer for $400. We are very disappointed that this washer with only two people only worked three years when we thought we had bought a reliable product that would last. Sent several messages in November but no response till today 12/13/17 after filing. BBB complaint filed and they decline to do anything. So this company just wants to sell products but has no customer service. They only give a year warranty. Of course if the product is not going to last they want you to buy more.

I bought the newest most energy efficient Maytag model M9BXXGMYM00 (for about 1K) from a local appliance store and after 9 months it wouldnt freeze. The local store picked up and left a loner for the fridge and made repairs in shop returning it in a week - great - except that approx. 11 months later the fridge again wouldnt freeze. The store sent repairman who charged 125$ to tell me it had leaked its freon again and would need repairs which were no longer covered under 1 year Maytag warranty. I asked the store to back their work but was only given a refill of the freon and half off the service visit. 2 months later the fridge is not freezing. I know because the repairman and store owner Mike told me that it had freon leak and that Mike himself had made repairs to the leak that the unit wasnt repaired.I have read that freon is toxic and can be hazardous to people with heart conditions and a list of bad effects. Maytag will only send someone to repair unit for a service call charge plus the repair charges and will not replace a defective unit. I can take the appliance store to small claims court over faulty warranty repairs but probably not the health risks - which are disputed by the experts. Ive read reviews and have heard from people who have appliance issues that the companies basically use a defective unit as a cash cow sending repairmen back again and again and never fixing the problem making a lot of money off of frustrated people who have bought a lemon from a company who doesnt back their product or their work. I was only looking for a decent refrigerator and paid plenty for one. I now have to get rid of a nuisance or pay to fix it - probably more than once and spend lots of time getting through the court vs. store owner process for any of the 1000 bucks lost on the defective toxic junk I got from Maytag.

My Bravos Washer and Gas dryer are only a few years old, and they have both been problematic to say the least! Neither Home Depot nor Maytag have been helpful. My washer has had the shocks replaced already, because it would constantly go off balance and shut down and they cant grease the bearings because they are sealed. So, now it sounds like an airport is in my laundry room! The gas dryer takes an entire day to half dry a load and its burnt on the inside!

Bravos quiet series 300 - After reading reviews on this washer and dryer I have to add my thoughts. I bought this set a few years ago and initially was very pleased. However, I am now having the same issues as everyone else. The bearing on my washer is bad and needs replacing to the cost of almost a new washer. My dryer started acting up at the same time, my clothes would not dry at all and I discovered the inside of the door was wet and after pulling out to check the wall vent, the vent had water puddled up inside the wall. The tubing from the dryer to the wall had mildew growing in it. Which may explain why my towels and clothes come out of the dryer smelling like mildew! The repairman was here today and repaired the dryer, there was a large amount of lint at the bottom of the dryer once he opened it up, which I believe could be a fire hazard. The seal (or felt seal) around the drum was coming off and had to glued back onto the drum. The belt under the dryer had come undone causing the dryer to not dry, but would spin. It is a shame that Maytag has not resolved the issues that everyone seems to be having, even if it has been years since we all purchased their product. Maytag is supposed to be a reliable product name and you would think they would like to fix this issue to keep their name clean! My first washer and dryer (which were Maytag) lasted more than 12 years and cost a lot less than this set which I dont think is more than 5 years old! I hate to spend more money on a new machine, but I may have no choice. Very sad customer right now.

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

I purchased a Maytag stove model mer7765wb in December 2011. Now its November 2014. My display board caught on fire and its burn out. How can a Maytag product go out within 3yrs. I purchased it from Sears outlet. As Sears customer I am very disappointed in this product. Thank God I was in the kitchen to put out the fire.

Loading is easy, operation is extremely quiet, dishes are very clean even on normal auto wash cycle. White, integrated depress buttons, full size, removable utensil baskets, upper and lower racks, top rack is manually adjustable, stainless steel tub. White front which is what we want not the ugly old metal stainless steel, usage buttons are on the upward facing edge of the door, pull down handle is nice size and very sturdy. Model is MDB8959SBW3. Even on normal auto wash cycle dishes are clean without much pre-rinsing. Purchased 10/14 from local dealer and professionally installed. So far we love it.

DO NOT BUY MAYTAG REFRIGERATOR. I purchased a Maytag refrigerator 3 years ago, now it started to leak water on the floor. Repairman said this happens after about 3 years to all Maytag refrigerators because the water hose is too small and gets plugged which causes water to flow into bottom of freezer; 2 inches of ice on bottom of freezer. Now we have to remove everything from freezer and refrigerator, unplug for 2 days to melt ice so we lose all of our food in freezer and refrigerator.

Washing Machine MVWC6ESWW - The fourth time was October 12; I called. Shreka at Maytag said she would send someone out at no cost on October 15, between 12-5 pm. Justin called from AE at 5:05 pm stating he was on his way. He then asked for my receipts. We were moving and had packed many things. He said he would call and find out. He said they were out 7/2011, 9/2011 and again 9/2011 all for the same problem. I requested in September 2011 that this was a lemon and send me another. I was assured if the same problem occurs, it would be covered. Well Justin said it isnt covered anymore and it was due to being made overseas. The cost to fix it is around $350 to $400. The washer cost me $383.40, plus I bought the matching dryer of $403.39. This makes zero since. Please advise.

I purchased two high end Maytag machines, one washer and one dryer, approximately 36 months ago. I did not buy the extended warranty because I was foolishly convinced Maytag sold reliable products. The dryer required service twice within the first 18 months. The washer, which is computerized, is almost unusable. The sensors dont work properly. It does not spin without continual restarting the machine. It takes me hours to wash one load of laundry, and even then it is not spun properly. I wrote Maytag headquarters twice via e-mail, with no response. Even though their website says someone will get back to you within three business days. I called Maytag on August 12th and was told there is nothing they can do because I didnt purchase the extended warranty. So the bottom line is you can spend thousands of dollars on their machines but dont expect them to last, or work. And Maytag will not stand behind their products.

Bought new glass top Maytag electric range. Only used oven 7 or 8 times when I was unable to close the door. Had to wait 12 days for Maytag repairman. Has to order new parts. Still without use of oven. Says its a known problem the hinges holding the door arent strong enough. Last stove 24 years old. Never had a problem.

I have owned this Maytag washer model # MVWC360AW0 since Dec/2013. I do not have a single complaint about this machine. It has worked flawlessly for 5 years and am very happy with it. I just follow common sense maintenance like cleaning it once every month (do a full cycle with just borax & baking soda 1/2 cup each) no clothes of course. Another thing I do is to leave it open after I am done washing so it dries completely before I close the lid. The washer looks and works like new, cant be happier...

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

So our 4 year old Maytag Dishwasher just took a crap. Thank God we were at the kitchen table when it started to smoke, which smelt like burning wires and unplugged it immediately. Repairman came out and said it would be a 3 to 4 hundred dollar repair. What happened to the great 10 year Warranty? Oh yeah, its a limited warranty which does not include wiring. Could have burnt down my 4 year old home, but thats ok, not covered. The good news, the upper arm I replaced due to wear and tear would have been a free repair, because it would have been covered! No more Maytags in this home, ever!!

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

Under class action suit in 8/2005, Maytag repaired my Neptune washer by replacing motor conversion kit. 6 yrs later the washer is having same problems as had originally; we asked Maytag just to replace the motor drive again ($190.00 part). They refuse, although this motor drive had identical life span to the one they replaced. It seems the replacement part was not new and improved, it only lasted as long as the original. Only now, we are past the class action suit deadline by years.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

Purchased my 1st brand new washing machine almost 3 years ago, a Maytag Centennial Washer for a little more than $600.00. Now it needs over $400.00 worth of repairs to get it working. Theres a reason the Maytag repair guy has nothing to do. Its because their products cant be repaired and are disposable. 25 years ago we bought our first washing machine that was used. It lasted for 22 years before it died. Maytag cant make a product that can last for 3. Also got stuck with a $65.00 service fee for them to tell me its broke and not worth fixing. Do yourself a favor and steer clear of their products.

Wow, my dream oven, or now nightmare! I purchased a Maytag dbl oven MGR6775BDS in 2007. The top oven stopped working first after about 3 years and this week, the bottom. I cooked a meal on Monday and Wednesday. Without notice, it would not go past pre-heat. I have called several people and they all act as if this was a truly unique situation. Since I have been out of work, both my regular and extended warranty have expired. I had good faith in a product that carried the name Maytag and the fact that it was on sale for $1,200. I didnt know I had so much company. Yeah, I was told I could purchase a repair warranty for the sale price of $340. Oh yeah, I replaced a 20+ year old oven for the new and stainless dbl oven of my dreams.

I bought this MMV4205BAB microwave thinking Maytag was a good brand and I wanted an over the range type. Problems began when it would stop in the middle of a cooking cycle. I called the repairman as it was under warranty. It was decided by the repairman that the weight of thing was too great for its thin frame, not letting the door close correctly. I got a new one and it, from day one, would make a shorting sound every time anything was cooked, on the stove top, under it, while it was on. It finally just shorted out. I have a Maytag washer and dryer that are also junk. So, needless to say, Maytag, 3 strikes and youre out. I will never have another Maytag product and I let others know what a great product it is.

I purchased a Maytag gas range in the past few weeks with Aqua Lift Cleaning System. I have only cooked once when grease spattered on the walls and floor of the oven. I have used the Aqua Lift Cleaning System 5 (five!) times and the grease is still there and very sticky. This system clearly does not do what it was supposed to do. I was fortunate to have bought the appliance where I could return it; however, it has been quite a hassle and I will have to pay an additional $100 to have the old one removed and the new one installed! I feel like Maytag should reimburse me the $100 because it is obvious to me now that I have found hundreds of reports of people not being satisfied with this feature.

Maytag Frontload washer MHWE300VW12 - I bought the washer and dryer in 2010 through Lowes. In Dec. 2012, it started making a loud sound when it would be in spin cycle. I called for service. When the repairman came out, he said the rear seal/bearing was bad and has gone out. The part and labor cost would be $1,184.36. Come on, are you flipping kidding me? Thats twice what I paid new for the washer. I bought them for the Maytag name. If I would have known it was a Whirlpool, no way I would have gotten them. My mother had a Maytag set that lasted 30 years. That explains why they dont show the commercials with the Maytag repairman that wouldnt have anything to do. Also, when the parts came in, they were Whirlpool parts. What a scam. Just more junk for our landfills.

This dishwasher is at 10 years old, but is a real workhorse. This machine cleans like no other! Never worry about our dishes being clean. But we have replaced the seal once.

My Maytag Neptune washer also has a problem with mold build-up and now the door lock assembly is totally gone. I was unaware of the class action suit or I would have joined. I am just disappointed!

I purchased a Maytag dishwasher at Home Depot in Roanoke, TX on 07-14-2011. Model Number: MDB7749AWB2Serial Number: F12604431Unfortunately, Ive just been obliged to open my third service call on this new dishwasher. The first service call was made in August 2012, just outside of the first year warranty period to repair a wire which had come loose in the control panel, making the dishwasher inoperable. The second service call (May 2013) was to replace the front panel housing and touch pad which had broken off at the screw-mounts holding it on to the door. As the handle to open the dishwasher is part of the front panel (which must be pulled out pretty hard to open as it does not have a latching mechanism) screws set into unreinforced, thin, plastic posts holding the panel to the door seems like a serious design flaw.The third service call which I placed last week (August 2013) is to address the fact that the dishwasher has become completely inoperable with no lights on the front panel and is completely unresponsive. To say the least my experience with this product (and by extension the Maytag brand) has been a serious disappointment. I guess the reason I no longer see those TV commercials with the lonely Maytag repairman is because these days hes actually really busy fixing broken down ** Maytags. I will never, ever buy any Maytag or Maytag-family brand appliance ever again.

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

My husband and I bought a Bravo XL washer in the fall of 2015. I certainly wish we had read the reviews on this site of this product. We would have saved ourselves a lot of money and grief. This machine does not clean clothes and actually damages them during the spin cycle as reported by others. This low water no agitator technology does not work on a top loader. Stuff doesnt come clean! Im not sure what we are going to do but we learned a valuable lesson the hard way. We purchased this machine in September of 2015 and are unhappy with it!

I have had it (Model MDB6000AWB) for a few years now. It had to have the door replaced per recall. This dishwasher does not wash dishes well at all; need to rewash many items after going through normal wash cycle. Also, all spokes are burning and falling off, along with pans getting burn marks. I am not sure how safe this is anymore. I am going to purchase another dishwasher, but not a Maytag!

Bravos XL washer- This is probably the worst purchase I have ever made, first off, at $1000 it was a pricey purchase however, I chalked it up to it will last many years without issue. After only 3 years, the unit leaked water and was so loud you couldnt stay indoors while it was on spin cycle. The bearings and seal were completely shot and needed replacement, after the sticker shock of having a good repairman fix the problem I decided to tackle the job myself. (Thank you YouTube). All was well for the next 2 years until it all happened again. Maytag is junk and will never get another dollar from me-ever! A Speed Queen TR5 now sits where that piece of crap used to reside. BUYER BEWARE!

We bought a Maytag gas range in Feb of 2011. Shortly after that, we started having an intermittent problem with the oven not maintaining the temperature. It sometimes would not heat up to the proper temp or sometimes would get there but not maintain it. We have had several service calls all for this same problem. Each time they would replace things... nothing worked! We called Maytag and they said they wouldnt replace the unit until the same part had failed 3 times. Well, the service company came out 5-6 different times in the first year and replacing the main panel twice and the sensor and some other thingies I dont even remember. Pretty soon the warranty was running out, so I bought an extended warranty due to the fact that the unit had never been fixed. They sent out two different service companies who also were unable to fix the unit. It is now 18 months since we bought it, and Maytag refuses to do anything since it is out of warranty and the extended warranty company will only replace the unit up to 75% of its cost. So yes, we are very angry with Maytag and the way they wont stand behind their product and their total disregard for their customers.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

The oven works. However, there are two safety issues. First, the flat metal panel above the air vent and below the instrument panel gets extremely HOT. This is the location we can easily touch, especially when we operate the instrument panel. We almost burned our hands. Second, the edges of the unit are very SHARP. We almost cut our legs. These are serious safety issues. In addition, we/I tried to post a review at Maytag site pointing out these safety issues. The review was twice moderate (i.e., rejected). Even though I used to like Maytag, this experience changed my mind.

I purchased a Bravo 300 MVWB400VQ in 2009. I knew in 6 months that I had made a huge mistake. The clothes began coming out soaking wet - the dark clothes have lint, pet hair, and rings on them. The large capacity drum is just that... a big drum. If I wash bedding in it, it becomes off balance and sounds like its fallen over. I have used only HE detergents, and I wash the washer (yes, wash the washer, does that tell you anything?) before the light comes on. Now the machine sounds like its full of loose parts or rocks in it when it begins to fill up. Its even worse when the water starts to pump out. Now that Ive read all the other complaints, I realize that Im doomed. All of these trusting people have been cheated out of nearly a thousand dollars for a piece of junk. What good is Consumer Affairs if there is nothing done when there are so many complaints? I will join any lawsuit against Maytag if ever there is one. This is another lemon that promised everything and delivered nothing.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

Wish I had reviewed Consumer Affairs reports. When our old Maytag stove required repairs we decided to upgrade old stove instead of putting money into old unit. Looks like a huge mistake. Not only was there a delay in receiving unit after placing order but oven will not preheat. Two weeks before Thanksgiving we were promised a working unit. Now we are only 2 days from Thanksgiving, 2 repair companies have been at home to repair. Requires new circuit board and a new regulator to repair and no promise we can obtain parts. Now I have to figure out how to feed my family for holiday. I am pretty well done and after reading other reports that they are better in junkyard I think I will try to make them take back this defective Model 8800 product. Sitting in our kitchen unusable for the holidays. Dont buy Maytag as customer service does not exist.

Convenience, small, clean while you doing other jobs, it cleans while you sleeping, it's not loud, not expensive, comes in different sizes and colors, it's another helping hand, you will love it, it's worth the money.

Maytag dishwasher model #MDB7609AWB2 - The control panel on this dishwasher has just gone out for the fifth time since 12/10. Last time I also had to replace the control board also.