I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

I purchased these appliances on 02-10-16 from Home Depot in Loganville Ga., for almost $2000.00. I filed the first repair call less than 3 weeks after delivery. The sensor panel was bad and had to be replaced. Now 8 months later the washer is not starting, AGAIN. The dryer will only dry one load a day or you get the AF code. This means that the dryer cannot push air over 5 or so and we need to have a vent booster fan (an additional $200.00) installed plus have an electrician run a new outlet. I returned to Home Depot with my complaint. Feeling that I have an inferior product, they tried to get Maytag to make it right. Maytag refused to offer any solutions whatsoever. Home Depot refunded a little over $300.00 for my inconvenience.The washer is an absolute ill-conceived piece of junk. It is ROUGH on clothing and does not remove soap. I started out with brand new (expensive) towels when I purchased this machine and 8 months later all of the hems have been snatched off and theyre unraveling and falling apart and are slowly becoming car wash towels.You cannot wash delicates in this machine and allow it to spin. Underwires in bras are badly misshaped or broken completely. You cannot wear them afterwards without being gouged by bent wires. The only way around this is to take away the spin cycle, but you better be ready with a clean garbage can to haul the dripping clothes elsewhere and hung up to drip dry. The washer has NEVER removed all of the soap from bed sheets. I have a dark gray set that show the soap best. Now I have to wash once with soap then wash again with no soap. This negates the machines being efficient.Unfortunately, I found the negative reviews AFTER buying the machine. My complaints are well known to Maytag, seeing has to how the same complaints are found online as far back as 8 years ago. I have been brand loyal for 30+ years to Whirlpool and thought that I was moving up with a Maytag, based on my parents 50 year experience... I was wrong! I will never purchase another Maytag product nor Whirlpool since Whirlpool now owns Maytag. I have researched and am of the opinion that Speed Queen is a far better product and plan to junk this set and replace them with Speed Queen.

I bought my Maytag washer and dryer in Monroe County in Georgia, USA in 1980. Its a 1979 product and it STILL works perfectly fine after 40 years! Im 64 years old now and Im hoping Ill never have to buy a new set although I would love one because theyre so pretty these days.

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

Purchased Maytag dishwasher two years ago from Home Depot. It worked for about six months before it would stop working. When adding a dish after initial start would cause the unit to just die. After unplugging unit for a day the start/cancel drain buttons will flash. After reading online about a demo mode have tried and gotten it to work periodically. I continue to read online and have found there is a diagnostic mode. The settings are in a schematic packed with the unit. I found mine written in French (part #W10321879A). I called Maytag/Whirlpool and asked for the English version. They could not and would not provide me with part #W10321878A the English version, a single sheet of paper. They will only provide to a licensed repair technician. I am only asking for what should have been included in the original purchase. I paid $850 for a dishwasher that is not chump change. I know the control panel is bad but I would like to use it until the new part arrives. I think I may return the control panel and take my losses and go buy a brand that is not owned by Cesspool (Whirlpool).

I do not recommend this product. I purchased them 2 years ago. Within one month, the drum stopped working on the dryer. This was covered under warranty. In the last month, though, I have noticed that there are blue stains on the new drum. I do not leave clothes in the dryer wet. Last week, the washer stopped agitating or cleaning clothes even though the cycle would still run. I called for a service call and paid $82 for this. I found out the transmission was not working. This is not covered under the warranty. The warranty for entire machine is only 1 year. The 2-10 year warranty only covers the drive motor and wash basket. I cannot understand why a transmission is not covered. I feel like they are not standing behind their product. Finally, after a lot of talking, I did get Maytag to agree to cover the cost of the transmission part; but I am still obligated to pay $150 for labor. Why are products not standing up to use as in the past? I am very disappointed with these products.

I purchased a Maytag dryer (MDE2400AZW) 2 years ago, but have only been using it for the last year - and fairly infrequently, as this is a dryer that my guests use. I called Home Depot where I bought the dryer (along with the washer). I thought I had purchased an extra warranty, but turns out I only had it on the washer - what was I thinking. I wish I had read these reviews before I made my purchase. My local repair man charged me $192.00 for a new heater and his time. Theres a whole 90-day warranty on the new heater!! I sure hope this one lasts more than a year otherwise Ill be buying a new dryer and it wont be Maytag.

Replaced a Maytag Bravos xl washer and dryer in 2015. First year was fine but almost right after the warranty period, the spinning cycle was loud. You cant even have a conversation near the washer. I put up with it after calling the repair department. Because I was told that it will cost as much to repair than buy a new washer. Now the washer does not drain when a small amount of cloth are in the washer. Dont buy this washer and dryer. Maytag is not as good as it once claim.

Maytag washing machine Model # MHWE500VW - 2 control boards only last 4 years. I paid top dollar, $1229.00 to be exact and the parts and labor are $659.00 with no guarantee that there wont be further problems. Technician told me that this is typical of Maytag products. Contacted Maytag and they told me to take a hike and have a nice day. I will attempt to get some help from the place of purchase, Hamai Appliance, Maui, Hawaii.

The washer is making loud noises. I had a repairman out and he said the transmission was shot. This washer is only 7.5 years old and the set I had before lasted 19 years. It also was a Maytag. My mother, sisters and aunts have always stood by Maytags and I am disappointed that this washer being 7.5 years old is shot. The dryer to the set is working great!

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

Fridge leaked all over our floor and ruined it! Very unhappy! When we open the freezer we find a sheet of ice on the bottom. We have to keep a towel on the floor so we dont slip and get hurt. I finally get a new kitchen and the fridge is ruining it! Yuck.

The washer and dryer were purchased together as a set 4 years ago in 2010. There have been times where I actually had clothes come from the washer completely and partially dry due to lack of water inside the washer! It fills based on how many clothes are in the washer or capacity that it senses. I have had so many clothes dry washed and torn up due to its use! If you set the washer to the wrinkle control position it does not go through the last rinse and spin cycle, you must reset it to the rinse, drain, spin cycle again in order to finish processing that load.It has already thrown its belt 2 times! Which my husband had to fix since we could not get in touch with anyone at Maytag who knew what we were talking about! If change gets stuck inside the washer bin in the little groove in the tank it is very difficult to get out, Im sure everyone has washed a pair of pants with the change still in the pockets, yes I know this is user error but if you dont know the change is in the little grooves because you cant see them, it stops the washer! So be sure to search this every time you do laundry!The dryer has a mind of its own! Sometimes it will finish drying your clothes, sometimes it wont finish the time set! Theres no reason just doesnt finish! There is so many reasons I will never purchase this brand again. Ive run out of room and patience. My clothes look like Im homeless!

Just replaced a washer that lasted over 7 years thru 3 renters with the Bravos top loading washer. There is nothing efficient about a cycle to take 73 mins to wash 20 articles of clothing (t-shirts, socks and underwear). The machine dont wash the top of the load. Also the deep clean feature isnt deep cleaning. I recorded a video of 20 mins of the machine not washing properly before going into rinse cycle. If this item dont produce refunds of the amount of water wasted RE-WASHING and electricity because it doesnt clean on first wash, then its time for Maytag to pay my utilities. For the money spent on the machine, going to the laundromat every other week with 1 roll of quarters each trip comes to be I can wash for 4 years and will outlast the longevity of the machine before it breaks! Also bulky mode is how you get more water in the machine but will take 63 mins to wash.

Bought a Maytag Dishwasher (Model No. MDB7749SBM2) in Sept. 2013 and I am in need of repair for the control panel. The dishwasher is in a vacation house and isnt used on a daily basis. I always thought Maytag was a reliable product but Ive been reading the reviews and the control panel is a problem on relatively new units. How do they get away with this. The unit was around $600 and now Im stuck with a big repair bill... and it appears, from what Ive read on this site that it is a common problem. Maytag has replaced the control panel part and, as far as I am concerned, they should have provided them to all the consumers who were stuck with the defective ones they sold us in the last few years. Now we all know why we dont see the Maytag repairman sitting around with nothing to do on TV. Hes working his ass off trying to fix the dishwashers.

We purchased a Maytag front load washer in May 2006 (MAH6700AWW). In November 2012 we had a leak and called a repair service. We were told it was the dispensing hose which had a hole worn in it and was replaced. In February 2014, we called the same service and was told that we had the same problem. Now in November 2014 we are experiencing the same problem. We have notified Whirlpool of this problem and each time were told that the machine was too old to reimburse us in any way. Guess who wont be buying any Whirlpool products if they do not back up their faulty workmanship.

The fridge is very loud, leaks water from ice maker, runs all the time. I have had two repairman out to try and fix it but still not fixed. It is one year old now. If I could get my $2100.00 back I would take it and run. It so loud we have to turn up the TV so we can hear it. Drives us crazy.

My Maytag is 2 weeks old, and knew from the start I had a lemon. The compressor sounds like a giant freezer. I had the service man take a look at it, and while he was here the compressor did not come on. He pulled the plug from the fridge and turned it back on and still it did not turn on. I asked him to stay till it turned on and he said he could not stay any longer. I waited for him from 2 PM till 7:30 PM. He was to arrive between 3 and 6. Talk about frustration, and I only wish I had read all the reports before I bought this junker. I was so worried I decided to get the insurance for 4 years. The reason the ice forms is because you have no control over the ice. You cant see them and they get stuck. I had a side by side before this, and I can kick myself for not buying a side by side again. I was told to shut it it down when youve had enough ice cubes, to stop it from getting stuck. This ice maker is so big and so hard to pull out and the switch to turn it off is on the inside. So far my only complaint was the humming, but I can see a tough road ahead.

I purchased a new Maytag top loader at Home Depot. They delivered and set up. From the first load, I have had problems with the washer stopping and jerking. Clothing becomes a tangled mess. I contacted Maytag, they suggested I make sure I put on proper setting for the items within the washer. I do not know how one can fail at putting sheets in the washer and putting the setting on sheets and they are so twisted you have to spend time pulling them apart. This happens to almost everything I wash. I believe that I have a lemon, still under warranty, Maytag believes I should pay for a house call. Home Depot will only forward the information to me that Maytag gives to them.

I bought this Maytag Dryer in May 23, 2015. I had nothing but problems. I had 4 techs come out and say different reasons why it does not work. I had the vent exhaust clean out. Still not working, the one tech said there was not enough clothes for the dryer to sense it wet. I did a huge load, still doesn’t work. The sensor for the vent keeps popping up and it’s cleaned. I have to pull it out and in to get the signal light out. Cant turn on the machine. It still does not work. I tried contacting Lowe’s, since I bought an additional services plan. They said I have to call every thirty days for three months. That means I have to take my time out of work and wait for a tech for three months to get make a complaint and TRY to get new one. I really disappointed with Maytag and Lowe’s. I have a tech coming out this Monday, 11/23/2015 for another services call. I will never buy at Lowe’s or Maytag again. How many times does a certified tech from Maytag have to come out check a brand new dryer?

Purchased this washer at the end of August and it was delivered the first week of September. On September 27th the rubber seal around the door somehow got tangled in with a shirt and was ripped off (absolutely no idea how that even could have happened) and spilled water all over the floor. I called Maytag on Sept 27 and they had a tech out here by October 2nd which was great. However, even though I had told them the problem and that the rubber seal was damaged the tech didnt bring one when he came. I had to call them last week to find out what was going on - they had the tech call me and he said that the part had just shipped and he should have it by next week - Today, I had to call again as there was no follow-up from the tech and was told that hopefully the tech will come on October 21st once he gets the part as he hasnt received it yet. I regret purchasing Maytag, as I had heard they had better service (local techs/parts warehouses) than LG or Samsung but that doesnt appear to be the case. 3 Weeks to repair a $1400 washer that I used for about 4 weeks is unacceptable. On top of the inconvenience Ive had to spend $40+ dollars a week at a laundry mat, plus waste my time. One star service.

Our Maytag Bravos Top loader with no agitator is headed to the junk pile after 1.5 years of BAD service. I honestly believe that whoever writes a good review on this machine is NOT an actual owner. Lets start with how it NEVER cleaned our clothes... The washer uses barely enough water to get the clothes wet. Soap remains in the clothes so the family is constantly itchy! If you add 3 additional rinse cycles, its still not nearly enough to get out the detergent and youre left asking yourself, What about the HIGH EFFICIENCY???? Next theres the issue of the water never being hot ENOUGH to kill bacteria (were back to the itchy thing). Its suppose to be an energy saver, but at what expense? Its not QUIET like promised (well maybe for the first few months). But upon opening the lid, you realize it was quiet because not a lot was happening to get the clothes clean. Now lets talk about the horrible smell... I dont know where its coming from... It occurs during the wash cycle and smells almost like a natural gas type odor. This is NOT because the washer wasnt cleaned once per month! Maybe its the bright orange RUST near the bleach dispenser or all along the inside rim of the lid... Remember its ONLY 1 and 1/2 years old. Before I get to the ISSUE that finally did this machine in... I have to mention the machines UNEVEN load response.. Brace yourself, it sounds like 1000 tribal drums... and if you dont readjust the 200 lb water logged load, it will just keep on filling up with water and draining indefinitely (so dont leave the house if youre washing jeans, blankets or sheets!). The FINALE of our machine is what I kind of always suspected it would be... the lid lock!!!! One day it stopped in the middle of a cycle and the door remained locked... After unplugging and retrying, the door unlocked, the buttons all worked, but the machine will not fill up with water or start a cycle. To be honest... I am so GRATEFUL! I get to buy a new machine and although Im pretty pissed that the machine died after just 1.5 years, we can finally have CLEAN clothes again, peaceful laundry days and get rid of the ITCHIES!!!! Bye bye FOREVER Maytag!!!!!!

We have had the oven, a Maytag Gemini Double Oven model mgt8775xs02, for 3 weeks now and I am so upset. First off, I became violently sick from the oven when we first used it. I had a horrible headache and then nauseousness and then the worst stomach problems I have ever had. The toxic smells coming from the oven were too much for me. We had every window open. I looked online and found other people who reacted the same way to their new oven smell. But now we are on the 4th time using the oven. We did a self-clean and I thought that would help but no, it smells like someone is pouring gasoline into my home. I smelled it in pockets throughout my house. I have had the gas company out twice and a repairman. They all cannot figure out the problem. I looked online to see if other people were having a gas problem from this model and I am not finding it. It is horrible. I feel like I am being poisoned. I have not had a working oven in 2 and half years and I was so excited to get this oven and now my new oven is making me so sick. I am not sure what to do from here.

Washing Machine MVWC6ESWW - The fourth time was October 12; I called. Shreka at Maytag said she would send someone out at no cost on October 15, between 12-5 pm. Justin called from AE at 5:05 pm stating he was on his way. He then asked for my receipts. We were moving and had packed many things. He said he would call and find out. He said they were out 7/2011, 9/2011 and again 9/2011 all for the same problem. I requested in September 2011 that this was a lemon and send me another. I was assured if the same problem occurs, it would be covered. Well Justin said it isnt covered anymore and it was due to being made overseas. The cost to fix it is around $350 to $400. The washer cost me $383.40, plus I bought the matching dryer of $403.39. This makes zero since. Please advise.

I read some of the reviews on the Maytag ovens. I too have the same problems! Have had control panel replaced and still have to set at 400 if I need to bake at 350. It also takes forever to preheat. Trust this review because I am one very unhappy consumer!! DO NOT buy Maytag!!

I will never buy another Maytag appliance. We built our home in 2005 and bought brand new Maytag kitchen appliances (refrigerator, gas oven/stovetop, dishwasher, and hood microwave). In seven years, we have had problem after problem with all four appliances. We had to replace the compressor in the refrigerator in the first 18 months and then the fan in the refrigerator about a year ago. We have had to replace the heating unit in the oven twice and the handle has broken off of the oven door twice. We have had to replace the handle latch on the dishwasher once and today, the microwave stopped working. We are not rough on our appliances (especially the microwave as we rarely use it), so I think the fact that every single Maytag appliance has broken down one to three times in different capacities in the last seven years says it all. We have had a very poor experience with this brand and will definitely never buy another Maytag appliance.

I purchased a dishwasher for $741 in December 2012. I called customer service department who told me that I should expect to pay since I did not buy the extended warranty. I thought by buying a high end appliance it would last 5 years without the control panel giving out ($300 cost with installation). Please DO NOT buy this brand!!!

Upon remodeling our kitchen about 4 years ago, we decided to put in Maytag appliances, one of which was the dishwasher . On Nov.29th, our granddaughters were playing with our dog when they ran through the kitchen and the dog started to yelp and went down and started to bleed. As she went past the washer her leg was sliced open by the bottom of the washer door. As it turns out, the bottom of the Maytag dishwasher doors has a sharp cut edge with no covers at all along the entire bottom of the door. We have also read about two children who have had the same thing happen to them. This is a very serious problem that needs to be addressed as soon as possible. The first surgery as of now has been $3,600.00 because of cut tendons. It would be totally irresponsible not to warn all consumers of this extremely serious hazard considering most families let their small children play in the kitchen

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

Buyer Beware!! Purchased my Maytag over the range microwave in May of 2014. It has a manufacture date of Feb. 2014, and it is now Sept. 2014. It is a very nice looking unit but a bit oversized. My handyman that installed it had to raise my cabinets above my stove two inches to avoid it being too close to the range. The motor is pretty loud and It often times does not heat evenly. The light on the unit that shines down on the range is not much better than the power of a night light which is a bit disappointing considering it looks like a higher end unit, and down to the reason I am writing this review today is that for the first time I went to change the bulb. I unscrewed the the light cover which is placed awkwardly toward the very very back of the unit, only to find that when I went to twist out the burnt out bulb (that has been in there since I purchased the unit) that the bulb broke off after hearing what sounded like the break of a seal of glue, and the bottom aluminum piece of the bulb is stuck in the bulb socket. I found that the bulb is placed in an awkward place behind the light cover. Instead of the bulb facing to the left or the right or to the front of the unit it is facing toward the back which is making the bulb socket impossible to see, which means that in order to screw in the bulb you are screwing it in from an angle that you cannot see unless you climb on the range and lay on your back, or get a mirror to help see where you are screwing in the bulb. This is just a very awkward and unpractical design coming from such a well known company with such a common and ordinary product. Now I am sitting here writing this review and I am trying to figure out how I can remove that little piece of aluminum stuck in the light bulb socket and since it is not facing to the left or right and facing toward the back, it leaves me about less than 1/2 space to work with using my hand or a tool to remove that piece, or I can just leave my broken bulb piece in there and screw the cover back on until I call service for Maytag. I believe it is still under warranty but from others experience that I have read about I am not feeling confident I will receive great service or a desirable outcome. Wish me the best!! Thanks for listening!!

When I bought Maytag Neptune top-load washer, it lasted three months. I had to have the rockers replaced. Three months later, the lock switches went bad. Six months later, the main circuit board went out. Thank God it was under warranty. Ive had this ** washer four years and it broke down once again. I dont have any warranty and the money. They want to fix it. Im going to go out and buy something else. Piece of junk. It makes no sense. And when the first situation arose, I did ask if it had been recalled and of course, they said no.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

Our Maytag ref. is not quite 4 years old and it is leaking water on to our floor. The ref. is a French door with water and ice in the door and freezer on the bottom. We have to clean up puddles of water at least 3 or 4 times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasn’t Consumer Affairs demanded a recall on these expensive defective refrigerators to date?

In October of 2011, I purchased a $1,199 Maytag Bravos Washing Machine. It recently started making a really loud noise during the spin cycle (REALLY loud). I had a local appliance repair guy come and he told me the main tub bearings are bad, sealer is defective and that it would not be cost effective to fix it.I called Maytag and they offered to sell me another one for $839. I am very dissatisfied that I only got 4 years out of a $1,199 machine!!! Ridiculous!! I wouldnt mind a minor repair that cost a few hundred to fix... I get that. But for it to be junk in 4 years... I have a hard time with that for the price. My appliance guy said it was junk when I bought it. Year ago, you got 15 to 20 years out of a good washing machine. Now... I buy a high end machine and it lasts 4 years. And why would I spend another $839 for the same piece of junk!!! That would be throwing good money after bad. It is not going to happen. I promised Maytag that I would post as many reviews about their product as possible... so everyone can know that they make a lousy, defective product and charge a very high price for something that will not last. Dont buy it!!

Bravo XL washer and dryer - I had the washer approx 2 months before it leaked water all over the laundry room. The company replaced the washer after two weeks. Now the dryer has gone out after two years. If it cost me the amount stated by other consumers I wont be fixing it.

I purchased my Maytag Bravos washer and dryer in July 2007. As with any appliance, we always purchase the extended warranty as it usually runs about $100 on appliance. My first experience with problems was in February 2010 when the control panel went out. If I had not purchased the extended warranty, I would have been in trouble. It ran out in July 2008. It was downhill from there. In September 2010, it quit spinning; and the fabric dispenser would not work. I called again in September 2010. The tub was out of balance. In June 2011, the panel control went out again. In November 2011, it would not spin. In June 2012, the panel for control had to be changed out again. In July 2012, now the pump is leaking. And guess what, my extended warranty is up 8/1/2012. I contacted Customer Service, which said unless there was the same problem within 12 months, there was nothing they could do. Well, Im fired up. I intend on making a complaint with the Better Business Bureau and anyone else who will listen to me. I paid over $2000 for the washer and dryer, and it should last more than 5 years. This is ridiculous! When Whirlpool bought out Maytag, then the product went to crap! Dont tell me the Maytag repairman does not have anything to do now, because I know I keep him real busy. I am so tired of the companys just blowing you off when you work hard for your money and purchase a product for your family that should last at least 10 years. I am a principled person, and this is not going to go away easy. The repairman is coming next week to fix it again. I am going to give him an earful as well. The last one who came to change out the panel board (3rd time) said they had nothing but problems with this unit. Well maybe they made it that way, so when the warranty runs out, they can charge you an arm and a leg for the part and the labor to repair. I will never buy a Maytag product ever again. My next one will be the new LG washer and dryer. Talk about the lemon law. This product from what I am reading here should very well fall within that category.

I bought the Maytag because of its reputation and as a washer it hasnt disappointed me.. It gets my clothes clean with a minimum amount of effort on my part and it doesnt use a lot of water... I love my washer.

Purchased a Maytag Bravos washer model MTW6700TQ ON 5/5/2008. Also purchased extended service agreement. This washing machine was only five years old when it started rusting on the top of the body where you load the clothes and fill the detergent. Not in a million years did I expect a washing machine to be rust-prone. Its a washing machine. The service contract doesnt cover dust, mold, rodent damage, and RUST (like rust is an external source). When I called Maytag they were not surprised. They said the life expectancy of their product could be as little as a year and a half. Regardless of the extended maintenance expense I now must throw this piece of junk away. NEVER BUY A MAYTAG. This time I am buying an LG.

Purchased an Admiral Washer on 07/19/2010 from Home Depot in May of 2011 was washing clothes and washer flooded my wash room. Cold water would not turn off. Had to use shutoff valve on wall. Called for service through Maytags toll free number it took me 10 days to get through, then I was told that they did not have anyone in my area that could fix my washer that was still under warranty and there was nothing they could do. I called Home Depot and they said there was nothing they could do it was the manufactor problem.I Called several appliance repair places that advertise as maytag repair and they would not touch it!Called back in July of 2011 could not reach anyone at maytag service. My warranty expired 07/19/2011,yesterday 08/08/2011 I recieved a letter from Maytag wanting me to buy an extended warranty.I called an ask them why I should buy an extended warranty when they wouldnt even honor the original warranty they pulled up the records where I had called for service and told me I should have kept calling back that they take care of their customers etc. etc. but there was nothing they could do now because the washer was out of warranty.I called about a new water valve for this washer $56 for part $100 for labor including service call. Now I faced with a decision try to repair this piece of junk or scrap it a buy a new washer( not a Maytag or a Whirlpool) I am not rich I am elderly and live on a fixed income, it took me 6 months to pay off this washer at Home Depot!!!!!

We purchased the Bravos XL washer just over a year ago. It is being replaced 1/10/2017. Simply put this is the worst product I think I have ever encountered. Extremely noisy wash cycles leave residue on the clothes, clothes do not get wet in some spots. This washer is so noisy you can hear it from outside. What an embarrassment. You have to run the clothes twice first with detergent and again without detergent to remove the residue left over from the first wash cycle (not energy efficient at all). If I could give a minus score like minus 10 I would.

Model MBF 2258XEW3. I am very annoyed with this fridge. Never will buy a Maytag again. I went to this site to see what the problem with my fridge was and read that I am not the only one with this problem. From the beginning it never worked right. Often the food in the fridge got ice crystals in them so I had to up the temp. This made the freezer not cold enough so I had to lower the temp again. This is a constant affair. Now the bottom of the freezer is collecting an ice sheet or a water bath that has to be removed every other day so that it doesnt built up or leak out. Will have to buy a new fridge. But now I am worried that I might buy another lemon.

The stovetop is very hard to clean and gets stained easily. The heat works wonderfully and the burners are great sizes. The left side with the adjoining burners is great. The double oven is fantastic. Heats relatively fast. Another negative is the button controls. You have to push so hard for it to register. Its painful. Not the best way to do it. Just setting oven temperature is difficult. Wish that was different.

Bought a Maytag Washer, in 2010 the Bravo. Good looking washer and dryer. I bought a 4 yr warranty for both. My washer has needed service every yr of the warranty, leaks and has stopped running. Now it is out of warranty and it is leaking again. Was just fixed a little over a year ago. I am now seeing a lot of rust around the top of the washer. It has just about covered the one port where you put the bleach in. The seam around the top in the crease is full of rust. My dryer is fine, bought them both at the same time. I have never seen this on a washer before. My mom has had her Maytag for yrs no problem. I bought these thinking they would last, boy was I wrong.

Horrible machine. Purchased on 02/28/2014. I am 63 y/o retired housewife now. Machine used only for light washing, occasional king size sheets and weekly towels. I bought into the Maytag name, am so very angry that I did. Started a load at 1215 pm today... it is still sensing, washing, rinsing, spinning and then it starts all over again. Just unplugged from the power source, hopefully I can get the clothes spun out enough to dry!! Call and live chats to Maytag were frustrating to say the least. $400 plus Maytag service call to check out the machine not fix check out repairing would be extra. (I do not live in rural area, live 5 minutes from downtown Jacksonville FL!!!) Independent Repairmen will not touch this Maytag Model (cannot say I blame them!!). DO NOT PURCHASE A MAYTAG PRODUCT. This is a horrible company lacking in integrity, honesty and fairness. They sell shoddy, inferior products based upon past history.

Bought these in March of 2016. Got a 3 year warranty. In Feb 2019 the dryer burnt out the switch. Just by a hair it was covered. Now started working only on one cycle. The Washer with a 10 year limited warranty just stopped working out of the blue. ONLY 4 years old. Seriously???? during the Coronavirus outbreak!!!! I am beyond upset with this manufacturer. Geez my Kenmore washer and dryers lasted 17 years!!! My Whirlpools lasted 21 years!!!! What kind of junk are you putting on the market???? I was told at Lowes these were state of the Art machines - the best!!!! Here I am so stressed wondering what the Hell Im to do! Never buying Maytag again.

Dont buy a washer from Maytag, they put it together wrong and the transmission leaks so it will stop spinning after time and then it fries the motherboard. Too expensive to fix so you have to by a new one.. Their 10 year warranty is a joke and doesnt cover anything hasnt even been 5 years yet. Garbage products.

Bought a Bravos, large capacity, top load washing machine few years ago. (Purchased at a Lowes.) Been nothing, but one problem after the other!! I hate it! NO MORE MAYTAGS FOR ME. Has required several repairs of various parts. Now again, after being repaired few months ago, something else has gone wrong. Would have been cheaper to replace a 3-4 year old machine than keep having repairs.

Maytag dishwasher model MDB4949SDE3: This dishwasher is the biggest POS that I have ever owned in 40 years. The first one would never turn on and fill with water and after it finally did it leaked on my new floor. Waited 10 days to have it replaced. The dishwasher cycle is 2.5 - 3.5 hours and the dishes come out dirty. The top rack is not adjustable to wash odd things. I feel that these dishwashers need to be replaced.

I purchased a Maytag washer and dryer (Bravo series) in February 2011. The top edge of the drum in the washer is fraying. I contacted Maytag about the issue and never heard back. Now my dryer is not drying clothes. It feels like there is heat, but after 1 hour, the clothes are all hot and steamy, but still really wet. Our previous washer and dryer was over 10 years old and had no issues whatsoever, we just decided to upgrade to an HE W/D and now after just 14 months, the dryer doesnt work. They dont make them last anymore.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in Nov 2013. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within first 13 month. Then another valve got stuck about a year ago and the third one got stuck today Nov 19. So far I spent $400.00, just for 2 of them and the last one has not being replaced yet. This is a safety issue, because it always happen when the stove is on and will not turn off. I need Maytag to replace my stove because I am afraid this will burn my house down. I bought Maytag because they always advertise as quality product, and now I have to live with the nightmare of burning my house down.

Bravos XL Washer and Dryer (Maytag) is the worst appliance set ever. Not enough water in the bin, residue despite using the correct detergent, and clothes which do not even get fully wet during the wash cycle. I am so sorry I purchased this pair - I do like the heavy duty spin, and the dryer does dry (but the door clasp has somehow come loose and stopped working - has to be wiggled into place every time I close the door). The really frustrating part is the low water levels (and even bulky is less than a half a bin of water. I am attaching a photo with two sets of sheets, a towel and three wash cloths). Most cycles only put about two inches of water in the bin - appalling. And the long long long cycles - what is energy-saving about having to do a load twice and using more than an hour for one cycle? I wish I could adjust the water levels. Seriously disappointed in this duo. Sorry I wasted my hard-earned money on it. I was seduced by a pretty exterior.

Purchased a Maytag washer for my family of 8 because we do a lot of laundry and our Samsung washer failed after 3 years. I thought Maytag was a more reliable brand and was hopeful. The machine stopped working after less than 4 months of service. Manufacturers warranty repair came out and said it needed three new parts, motor, clutch and chip - said it would be another 2-3 weeks depending on parts. So all total without a washer for 4 weeks minimum - call the customer service people (first one was rude and short), 2nd one after 45 minutes on hold - told me the were no other options other than wait for the repair. Four months after a brand new washer and it failed. I requested a replacement option and they said no way. Their hotline talks about a positive customer experience and that seems to be a joke. Not helpful, super frustrated and they do not seem to care about the customer experience at all - terrible product and service

Recently I purchased a Maytag Bravo Washer and Dryer. These two items are the single worst appliances I have ever purchased. They are loud, ball the clothes into a knot and run forever. I plan to sell them on Craigslist and buy a Speed Queen.

I have had this washer for a few years now and it is the WORST washing machine ever. I cant even wash a lightweight cotton blanket. It continually unlevels even with me rearranging the blanket over and over. Ill add some, take some out, whatever. It still wont work. The blanket fully wet is also HEAVY and with my arthritis, is very hard to pick up. I dont think enough water goes into the drum to actually clean the clothes either. The clothes at the end of the cycle come out in a weird mushroom form. And when the clothes do get through a complete cycle, they are twisted so tightly it is hard to get the wrinkles out in the dryer. Why would they sell a machine like this without having testing it more first? Dont get suckered into the Maytag name. Terrible washer!

Our 26 month old Maytag fridge (Model MFF2258VEM8) was the french door freezer on bottom modern style fridge. The freezer stopped working. The repair shop took the fridge away and repaired a leak (quality control issue) and then the compressor failed in a test. They wanted $700 to make a repair that would have a 90 day warranty about 1/2 the cost of the fridge. Maytag was contacted at multiple levels and they would not even provide a free compressor or provide a substantial discount on a new fridge. What a way to treat a customer who once had all major Maytag appliances in our home. We decided to get a GE Profile fridge and are very happy with it. I will never buy another Maytag appliance. I dont think it is the great company it once was years ago.

Neptune washer and dryer, an all around good buy. Low water use and large capacity for the pair. Bought the pair in May of 2001 and have only had one, very minor, service call. Buying online usually proves to be the easiest and cheapest way to go. Economical delivery costs. Noise and vibration and overall solid construction. Dancing washers can be a real cause for being a deal breaker. Auto shut off for balance is a must. Cleanliness of wash and wear caused by washing and drying. Large capacity and multiple cycle selections for both the washer and the dryer are necessary.

Our $1,000.00 Maytag Bravos is only 4 years old (also bought the matching dryer at the same time). We have had to purchase two new motherboards for the washer and now the uL, during the spin cycle, comes on and my clothes will not spin out. I have followed the manuals directions to unplug, wait, replug, redistribute, etc... all to NO avail. So very disappointed with this machine. Bought it because it was a Maytag, but will never buy another :( I had this machine repaired with major amount of parts and expense (due to the uL problem), BUT the uL code still keeps coming up. I am one really unhappy customer.

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

I purchased a set of Bravos 4 months ago and what a bad purchase! I wish I would have researched here first. Being environmentally concerned, I bought it because it was supposed to be high efficiency and low water usage. My clothes are being destroyed by this machine. They come out in a massive tangled ball, covered in ink and animal hair (after a wash or two, they are completely embedded into the fibers). Sometimes there are dry spots after I take a load out of the washing machine. No idea how that could happen. It torn my favorite sweater, ripped sheets, bore a hole in a towel, ripped pillows, and DOESNT EVEN CLEAN! I have to wash my clothes twice MANY times to get the dirt out which doesnt bode well for energy efficiency. Im calling them again today to try and get them returned for advertising that they will save me money. Not even close! They are a rip off! I gave my 35 year old set away and wish I had it back! Maytag is JUNK!!!

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

I have had nothing except trouble with my new Maytag Bravos washer! I first had a suspension arm or something like that replaced along with the agitator. My water cycle has never worked correctly since it was new. I take out the clothes and half are still dry. My daughter washed her kids’ clothes in the washer while she was living with us and the stains did not come out. She thought that is really unusual since they werent stains that normally you would see left on the clothes. I went to my father-in-law’s house (they have a front loading Bosch), took her detergent with her that she used here and guess what? It’s just one washing and the stain was gone. She had washed the clothes in our washer at least 7 times trying to get out the stain. Now, we have such a loud noise that it sounds like it is going to take off. Then, the bottom of the washer started to leak. We took it out and checked it and we cant find the leak. The clothes smell awful when they come out of the wash. I dont know if it is bacteria build up. I use the cycle cleaner when I am supposed to. This is so sad. This is the first time I have had matching washer and dryer and I wish I would have kept my old Sears model that worked great. I havent decided if we want to fix it. With the price to fix it, I can buy one I might like. Never will I buy Maytag again or another Whirlpool without checking out the reports.

Our front load washer is two weeks past the one year warranty and need $650 in repairs! I will never purchase a Maytag product again. My last Maytag was 19 years old when we got this new front loader for energy efficiency. You dont save money when you have to replace it after one year.

An average refrigerator/freezer at best. I would not recommend it unless you also buy a service agreement to fix things that go wrong with it. Ice maker went out.

I have a Maytag MEDC200XW3 model. Good price reliable and rugged. It washes all the way from my delicates to my husbands heavy fire protective clothing with no problems. Holds lots of clothes with no issues either!

So sad, purchased brand new Maytag washer and dryer, Commercial technology (MVWB766FW) labels. Looked and appeared impressive. Machines cost almost $1,000 each. Had twenty year old machines that still worked, I didn’t want to face a unexpected breakdown and decided to replace. What a mistake. I’m 67 and all my life from grandma through my mother Maytag was the best, not anymore. Once my equipment was installed I washed a load checking frequently, noticed almost no water in the huge tub and my clothes being beat by the agitator but not enough water to move the clothes. I tried to change to high water setting but had to cancel this load to do so. Once on high water setting I started the load again, water still very low and agitator just rubbing the clothes directly next to it, no movement of the clothes at all. Ran completely through the wash cycle but when moving to the dryer noticed some light blue shorts had dry spots, many, which had never been wet even through the wash, rinse, and spin cycles. Had a warranty service call and was told this is how the machines work. I told the serviceman had I known that I would have never bought the machines. He told me the salesman should have explained this to me which he did not. The only way I can wash my clothes in the new, expensive machine is on bedding cycle with high water setting on. Sad day when American companies can legally sell such crap. Also, called the company where I purchased and ask about return. To that I was told once I made the purchase they were mine and Reid’s Appliance in Santa Barbara didn’t take returns. Reid’s Appliance can’t be trusted. Buyer Beware, this stuff is junk. I will be throwing these machines out soon as they aren’t even sale-able on the used market. MAYTAG RIPPED ME OFF.

I purchased this dishwasher from Sears in July of 2013. Barely 3 years ago. The last few months the controls have been acting odd. The control lock would automatically just turn on at odd times. Yesterday when I hit normal cycle it went to a different cycle and had many other options lit. It would not start. Finally it went dark, no lights, no nothing. I see many people have had these types of issues with this type of Maytag dishwasher. Disappointing. A dishwasher should last longer than 3 years. Sears said they would send a repairman out but it would have been minimum $200 after it was all said and done. Id rather own a non-Maytag dishwasher so we went and bought a different brand.

My Neptune Maytag pair have been dependable. Great features. Now at 20 yrs old still kicking. Washer-front loader now has issue with fab softener going into wash correctly. Could be build up? Trying to self-fix. Very gentle with washing fine things. Hope I can keep going with them.

Spent $2,000 on Maytag washer and dryer in September of 2020 thinking we were buying quality and a company that backs their products. Forward to January 2021 and were not able to schedule service through their website. Not able to get anyone to answer their phones. Called what used to be our local Maytag service and they told me Whirlpool took over Maytag warranty service and cancelled all the contracts for local repair shops. So, not only do we have a 4 month old washer I wish we had never bought, we cant even the Maytag to service it under their warranty! Never again...

MCBH979SAB0 - I am also frustrated with Maytag for the same exact problem... the control panel and the dishwasher not working just after our year warranty went out. I purchased this product because of a recall on my former Maytag dishwasher. I was told I should purchase this new model to replace it, only to get fooled again. This seems like BAD business on Maytag! How can we get an official complaint to someone who can fix this? Why would a company like Home Depot continue to support this business!!

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

I am very dissatisfied with this Maytag Gemini oven Ive had it for 4yrs. It has been in the shop twice for the same problem. Temperature control. It is down again for the same thing temperature control. The repairman, who I had to look at it, says the bill will be over $500.00. I paid $1300.00 for this stove. I cant afford to put any more money in this stove. I had to pay $100.00 for repairman to tell me this. The model # met8665xw02 serial#D30522404. Is there a recall on this stove? There should be. I sold Maytag products for several years at Circuit City. I always pushed Maytag instead of another brand. I believed in Maytag. The repairman hasnt been lonely to me.

Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

The whole Control Panel lights are turned off for several minutes. Then they return on. Frequency? Few times per day. Reason? We dont know. No water or ice are dispensed when this happens. No water pipe is kinked, water pressure is OK, no problem with cooling system and nothing happens with food inside refrigerator or freezer. There are no mention made in trouble-shooting section of customer manual. What should we do? In spite of this, we are satisfied with the product so far, after 3 years of use.

Recently started having puddles of water on floor every morning. Just noticed a thick sheet of ice on freezer floor when I had trouble closing the freezer door. Also the water dispenses very slowly. Removed filter and it would not dispense at all. Will try melting the sheet of ice to see if that helps. Purchased 2011.

Peeling of paint off the oven finish, inconsistent heating, fan goes on and cant shut off until the oven cools, have to leave door open in order to shut fan off. The paint peeling is really bad. It is right where the heat escapes from the oven, have to touch up paint every so often so it doesnt look so bad and the discoloration is covered besides the peeling.

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

Like in a previous posting I also have a Maytag dishwasher, model MDB7749. Just this weekend we had our third control panel go up in flames. Thankfully the breaker hit and it burned itself out quickly. We had previously had one go out where it would just restart in the middle or near the end of a cycle. One other time, we heard the popping and saw the small black smoke come out from under the panel covering. This last time we were in the other room and heard the popping, and then smelled the burning. Aside from the panel issues, this has been a decent dishwasher. But at this point with a third repair I could have bought a new one. This is the only appliance I havent bought the extended warranty on and I regret it. Hopefully Maytag will add this to their previous recall.

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

This is a horrible product. Do not buy one. In fact, do not buy any appliance made by Maytag. I purchased a Maytag Jetclean Plus Series MDB8959AWS brand new on 2/22/12 and had it installed. The machine stopped working not even three years later. The control panel does not light up at all. There are pages and pages of complaints on the Internet about this dishwasher and Maytag. There is a class action lawsuit against Maytag in California for faulty control panels. Maytag needs to be taken to court to be held financially accountable for making false claims and selling defective products. I will never, ever again buy any product made by Maytag.

Purchased a Maytag Centennial top load washer that will not fill with enough water to wash clothes. The washer was purchased from Lowes on August 17, 2016 and we tried to return but Lowes refused because we were passed the required 30 day return period. We contacted the Maytag company and they sent out service people who reported that there was nothing we could do other than wash small loads. The company also reported that if we tried any of the solutions on the web we would violate our Warranty. Since we find ourselves in this spot (we should have read all the bad reviews here before the purchase) we have decided to place the machine in a very visible spot across from a new 100 store shopping center on a truck with a 4x8 sign warning the public not to purchase this product.

Two years ago I bought a matched set of Maytag Neptune washer and dryer. Although I bought really liked the front loading and large capacity, I bought them because they were Maytags. I remember my parents grumbling that they couldnt afford a decent washer or dryer like Maytag and had to settle for Kenmore or some other brand that they figured was inferior. I noticed that they struggled through 20-25 years of maintenance free use of their inferior appliances. So when I found a pair of Maytag, I thought I had finally arrived. I was 60 years old and I knew this would be the last washer and dryer I would ever have to buy.It is now 2 years later and we developed dryer problems. The repairman found the computer malfunctioning and suggested it would be cheaper to replace than to repair. We asked him to check the washer while he was here and his diagnosis was similar. The drum bearings were gone and probably too expensive to repair. The Maytags are now in some scrap yard and I now have an inferior washer and dryer and I am looking forward to many years of maintenance free struggles. I used to think that Maytag repairmen are the loneliest people because their machines were reliable. I now know that they are lonely because all of the Maytags are garbage and not worth fixing.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

Dual oven - one is a convection oven. Never used the bottom drawer so that was wasted on previous range. I purchased a white appliance to match my others. The white stove top is a pain. Too bad it wasnt black. I checked this model online and found a good price in the city. I contacted the local Home Depot and they did a price match less 10% - all a bonus. The ovens work great although I have not tried the self clean. I have read that similar models have problems related to the self clean feature - high heat and circuit boards. My plan is to have a fan directed at the top of the stove when I use it and the range hood fan going. The convection oven is great - hard to mess up a recipe with that. The dual ovens are truly a great feature - strongly recommend. The keep warm is great also - nice to have two things cooking at the same time. That being said - the bottom oven is low, but that is worth the extra cooking space.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

In December 2017 I bought a Maytag Bravos (w/o agitator) based solely on past experience (56 yrs.) of buying from Maytag without any complaints. A friend told me I wouldnt be happy with my purchase and she was RIGHT! It doesnt get my clothes clean to my satisfaction, my towels are all getting snags as well as silky sheets and pillowcases and dark clothes have a soap scum line on them. I have slightly better luck if I wash everything with the deep water level option but I still need to wash dark clothes a second time without any soap or fabric softener to lighten the scum line.I am very careful to use minimal amounts of high efficiency detergent but that doesnt help. I called Maytag and complained within the first month but then we were gone for the month of February and I just never followed up with them. Now Im sure its too late to do anything. I wish I had listened to my friend. Hopefully I can save another consumer from making the same mistake I made.

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

Our Maytag oven (not sure model) in the first year started doing crazy things with the oven computer. The oven would shut off and come back on and the display would be garbled. Also when my girlfriend tried to pull the turkey out, the rack fell off the left side and dumped all the juices into the oven. She almost got burned and there was a lot of smoke. The freakin rack should never fall off! Also our dishwasher is on its second control board. I lived by Mr. Maytag and his airplanes/helicopters at Crest airpark in Covington, WA. I wish I still did. Id like to ask him what he thinks of his crappy products. You get nothing for your money anymore. Im not sure but Ill bet both of my problems with these products have something to do with saving a buck by making this crap in Mexico or some other *** hole. Im just glad Maytag doesnt make airplanes or medical equipment.

Washer Bravo MVWX655DW0 - Maytag has shipped the wrong part twice, sent me the right part which is faulty and the 4th one arrived today. I have not had a washer since 9-16 October 9, 2017. I am writing to tell you about my experience that Ive had with Maytag over the last 30 days. I have owned several Maytag and Amana appliances in the past; along with owning several currently. Over the years, weve had a wonderful experience owning these appliances however the last 30 days is one that has been unbelievable. On September 18 on a Monday early in the morning I called Maytag service line. I spoke to a young lady who had difficulties finding me in the system and did not know how to make an appointment to have a Maytag repairman come to my house to look at my washer. I did not take down her name as I thought and trusted that the company was acting on my behalf and would take care of me.I spent several minutes explaining to her that I did not live in Indiana that I lived in Iowa and that I would need a repairman who is close to my hometown. She continued to give me phone numbers with area code 407 in Indiana and then kept repeating some type of a ZIP Code 49 something for Indiana. I explained to her four different times that the zip codes in Iowa start with a five and the area code would be a 515 number in the area she was looking at. She finally gave me two phone numbers, one that did not work. I asked for a repairperson out of Jefferson. She told me Cranston Repair and gave me the phone number. She told me to call him. I told her that I would go with the Cranston repair since Jefferson with my hometown and it was close to where I lived.I then asked her if she would make the appointment. She told me she didnt know how to make the appointment and she kept messing up with the system. Not sure if it was her first day or not but that was fine so I said “never mind I will set the appointment up myself. I then asked her to double-check to see if our new Maytag refrigerator that we just purchased was registered. She told me she did not see it but all I needed to do was call back the next day with the model and serial number and anybody I spoke to on the phone could go ahead and get that registered. I thought I had registered online; I only wanted to double-check but she didnt see it so I assumed I did something wrong and then would make the call back the next day.I called Cranston repair and scheduled an appointment with the repairperson for the next day Tuesday, September 19. Repairman came the next day on time, looked at the washer and found that the transmission had gone out. I had purchased the washer just shy of two years ago. The repairman said that he would have to order the part and would let me know how long it would take and would return to fix the washing machine. He called from my house and was told that the part was on backorder until October 5. After the repairman left the house I decided to call Maytag back and express my disappointment in the product as Maytag says they stand behind their products and the fact that it was not even two years old and that a transmission would go out. The individual I spoke to this time, Antcwaniqua? Not sure about spelling, listened to my story. She also told me the part the repairman ordered was not correct.I needed part W1 1132267. She said that was a substitute part for the correct part that I needed which was W11035204. I told her that the part number ending in 204 we were told was on backorder until October 5. She said no, the part may show that in the system for repairmen but Maytag can locate the part in a warehouse, it would be shipped in 3 to 5 days. I told her that he had called a place in Davenport, Iowa. What she would do because of all the issues I was having was she would go ahead and ship the part out to me at no cost in 3 to 5 days.I wasnt sure about that warehouse thing. It didnt sound convincing but at that point I had to go along with it. What was shipped out to me was the substitute part W1 113-2267. At this point she told me that I would have to pay to have the part put in; I agreed to that on I want a new washer or I want my washer repaired within 72 hours at no cost. I have not had a washer for 3 weeks plus. Repairman in coming Friday and I am not confident that the 4th gearcase part that came today will work either.

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

This is not my first Maytag. Bought this one in August 2017 from Home Depot. Now all it does is make a grinding sound. No lights. Not anything but noise. I bought one without all the digital because I thought that could be more problems. The only part that is digital is the start/pause button. I liked the idea of less water and no center. It balloons the clothes when it is finished spinning. Didnt start out that way. I use the right detergent and wash it every 30 days as it suggests. Cant afford to call a repairman on such a new washer.

I purchased a Maytag Electric Range (Model: MER7662WS1) at Lowes in February 2011. After few months, we found many rusty areas on the stainless oven door and on the stainless drawer.On 9/8, I called Maytag at 1-800-688-9900 to complain that stainless steel is not supposed to rust. A representative took the initiative to schedule A&E Factory Service to come to my house for a warranty repair, and assigned me an order # 40629499. I did not request for this service call and naturally, I regard this as a warranty service or a service of quality check of a product.On 9/19, a technician came to check the rusty area and confirmed that the stainless steel have rusted and the rust will eat through the panel. The technician called Maytag, and got the answer that Maytag will not pay for his visit because its not under warranty. The technician then checked the warranty manual, but could find not any statement that neither rust is cosmetic nor rust is not covered. The technician asked me to pay $132 for his five-minute checking service. I was so upset and called Denice at A&E Factory Service at 1-800-905-9505 to bill Maytag directly. She ignored my request and said that I should take it to Maytag.After a couple of hours waiting, holding and transferring, I explained to two Maytag customer service representatives my problem, only to get a Sorry, its not covered, its cosmetic, reply. I insisted talking to a manager and finally got Melinda at Care Solution Team. She, too, refused to waive the charge for me and claimed herself as a supervisor and decision maker and theres no one above her who could resolve this issue.I emphasized that A&E service call was authorized by Maytag, I did not order the service. Who would have thought that a service authorized by manufacturer is not covered under warranty? Besides, this representative failed to inform me that rust would not be covered, she should have known better. Therefore, I believe that the person who initiated the service call to A&E should be held accountable. But Melinda never wanted to agree with this logic and kept saying, We dont force customer to have home service. You are liable for the bill.She refused to pay for the service and forced me to pay the bill from the mistake they made. She even refused to give out the persons ID # and name of the person who called A&E. She only documented my complaint--whats the point of their documentation? If this is the tactic that Maytag is using to categorize rust as cosmetic (if rust can damage material, then you should not call it cosmetic), and ban customers from claiming the rust damage so they can use poor quality of stainless steel on their appliances to save the cost, then, it is dishonest to advertise that this oven is stainless.A representative even said that Maytag should have emailed me with the confirmation of service call and noted that its a non-warranty service. Also, A&E should have informed me before arrival that the service is not covered. All these were not true. First, I did not receive such email from Maytag or Whirlpool. If Maytag would have warned me with non-covered policy such as this, they should have the courtesy to call me in case the email was unreliably routed to spam box. A&E only informed me that they are coming the next day, but no such thing as telling me that the service will not be covered. Even their technician did not know about the non-covered issue, and had to call Maytag today to find out.Had the person who scheduled the service told me that the rust on the stainless panels is not covered under warranty, will I still allow the service call and agree to pay $132 for a five-minute checkup and watch the technician leave without performing any repair? I asked Melinda to let me talk to her supervisor but she said that theres no one who can talk to me, and the only way to appeal is to write to the companys executives. The address is: Whirlpool Corporate Office553 Benson Rd Benton Harbor, Michigan 49022. I doubt that an appeal will help me at all. I will take this matter to small claim court, I wont let them force me to pay the bill when I am not at fault.

Maytag Dishwasher model #MDB7759SAW3 continues the Whirlpool company legacy of subpar control panels in all of their dishwashers. It is telling that they have been allowed to market the exact same failing parts for well over a decade without any accountability. They had one recall circa 2007-2010 and pushed customers into purchasing the model I have which suffers from the exact same control panel design.To further frustrate the consumer experience, Maytag customer service reps and supervisors allege that they have never heard of a customer having issues with their dishwasher control panel before. The panel beeps endlessly and refuses user input regardless of whether the door is opened or closed. After a power disconnect it will reset and sometimes allow one load to be washed before resuming the non stop beeping. If opened and closed during the beeping it will cycle through a completely new wash cycle on its own and resume beeping. Maytag customer service response this morning was, “thank you for being a Maytag customer”.We will my be purchasing their replacement control panels as they are of poor quality and it is well documented that the new ones fail annually as well. These are “high end” appliances and are not inexpensive. We will simply cease to use whirlpool, Maytag, Kenmore, Kitchenaid, etc. brands in our home and will advise everyone we know to protect themselves the same way.

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

The new technology on the washers is useless and saves no energy or water. People figure out how to get more water in the tub and use that setting. There is not small or medium water fill anymore.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.