The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

I purchased a new Maytag washer (Model# MVWC565FWO) from LOWES 18 months ago and the paint is bubbling on the inside of the door. Neither Lowes nor Maytag would do a thing. We have spend many $1000s at Lowes and considering the replacement cost is only $126 for a new door I can see Lowes following Sears for their lack of customer service and diplomacy in matters like these.

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

Nineteen-month-old dishwasher was repaired once while under warranty; 6 months later, same problem. They said they would send me a new part but I would pay for labor. I wasn’t happy but I agreed. I am being forced to use their people and pay first before the part is received and before the work is done. They said this is their procedure. If I must pay labor, I should be allowed to use whom I want. It is absurd asking for payment before job is done when the part is free. I have since checked the complaints, and there are over 200, with one woman on her fourth control panel – I will be on my second one. I feel this machine should be replaced free of charge. Its obviously a lemon!

We bought this refrigerator in 1998 and it is still going strong. It has gotten a bit noisy over the years when defrosting, but it works great. It is not as fancy as the freezer over top, but it is large and so is the refrigerator.

Replaced my leaking Samsung washer with a Maytag and I really regret the switch. What a piece of garbage. It has been service twice (thankfully within the first warranty year) due to Main control board failure. Seriously, these washers are good for nothing. Also, the Sanitize cycle doesnt do a good job from day one. Save your hard earned money and buy something else.

Maytag, you are still trading on your good name but that will not last! I owned a Maytag, agitator style, for 20 years and it was still running just fine when we built a new house. I thought it would be wise to buy new appliances for my new laundry room so I chose the beautiful and expensive Maytag Bravos XL. I regret that decision. The washer lasted 4 years and began to have problems draining last week. The liquid that stayed in the washtub until the repairman could get here was so foul smelling! He came back today to replace the drain pump and now the washer is showing that the interface and CCU are not communicating. So now we are ordering another CCU and I hope this fixes the problem. I agree with all of you who say you will NEVER buy another Maytag again. Maytag, are you listening?

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

After having had Maytag Highlander washer and dryer for 28 years in our early married life, and continuing to think that Maytag was a quality product, we purchased the Neptune front load washer MAH6700AWW. Let me tell you this IS NOT your mothers washer, nor is this Maytag a quality product. First it was necessary to install water pipe shock arrestors because of the water valve on washer causing shock in the waterline when it closed. The automatic Softener/detergent dispenser didnt work from day one.Coins and etc. constantly kept getting under flippers and couldnt be easily removed. I found that it was impossible to remove the plastic flipper without breaking a plastic mounting tab. On my first call to customer the Maytag Customer Loyalty Team, aka Customer Service (CS), I was told that the plastic flippers were not available as a separate part, and that the entire tub assembly with plastic flippers would need to be replaced. WHAT???????? THATS LUDICROUS. After temporarily securing the broken flipper to the tub, I thought Id call again about a week later to see if the previous answer was correct. On this call, the customer service lady (whose name I have), said the flippers are available and that she would send two at no charge. A few days later two flippers arrived, but were not the correct ones. I then decided to drill two holes in the tub and remounted the broken flipper with two stainless screws as a permanent solution.Two pumps needed to be replaced. One was replaced under warranty and one by myself. The one replaced by me was damaged by a coin that made its way from the tub to the pump. Other washer manufacturers provide a means of trapping such objects before they get to the pump. The wash cycle stopped unexpectedly numerous times without reason, after which the code 5d was displayed. I called Maytag Customer service. The representative didnt know what 5d code meant. Her suggestion was to call a service man. Again, I called later to ask and was told 5d meant excessive suds which wasnt the cause. Might this have been a control problem?There were three incidents of water discharging onto the floor from under the washer over the last two months, which caused water to cover an area of approximately 5 by 12 resulting in extensive cleanup in addition to damage to stored items. Since these occurrences were weeks apart and unpredictable, I knew the problem would be difficult, if not impossible, to diagnose, even by a serviceman. I concluded that it was probably a problem with the control; either filling too long or not emptying the tub before refilling for the next cycle. Thats when I decided to send this troublesome Maytag piece of junk to the landfill.

Maytag french door bottom freezer model #MFF2558VEB5 - It stinks to read all the similar problems Ive had with my unit. Purchased Nov 2011. Problems started within a year. First minor, deli drawer broke. I use clear duck tape to operate it and that has been fine. But not acceptable. About a year ago the water leak out of bottom freezer was noticed. The bottom inside is frozen sheet. I break up and manually remove quite often. NOTE: I intentionally do not use, did not install, the ice maker - historically they are poor risk so I dont bother. The ice unit is in the machine but not installed. I assume my water build up which freezes on bottom related to poor design of defrost drain and that is supported by other comments here. I find it disgusting. Live and learn. Its B.S.

I agree with everyone one else and their experience with these washers. I took advantage of a credit for those replacing old washers with new HE washers. IF I COULD ONLY GET MY OLD WASHER BACK!!! Its only 2 years old and it sounds like - what others have said, like a B52 taking off (during the spin cycle). I dont have rust spots inside of the machine or out so Im not sure what the issue is but I really dont want to invest in a couple hundred of dollars to this thing. It stinks, doesnt clean well and now this! VERY disappointed...VERY. As a single mom, the thought of finding money to replace something that is new just disgusts me! Nothing like the old washers that last for 18+ years. Nice Maytag I will never purchase another product of yours and will spread the word!

The dishwasher is only one and a half years old and like many others are having trouble with the control panel. The model is MDB89495AWO which cost nearly $800. The dishwasher does not shutdown after an operating cycle. On contacting Maytag with the symptoms they advised that they have never heard of a similar problem. On reading the comments/experience of other Maytag owners I am undecided whether to scrap this unit and buy another make!

I wrote the below to Maytag on their FaceBook page, of course havent heard anything back from them. Adding this on since I forgot about it, I have dogs and wash their blankets often, not that theyre dirty just for the dog smell. I have to wash them on the sanitize cycle which is an 1.5 hours long because if I use the normal cycle which is only 43 minutes they come out smelling exactly the same way they went in. I saw someone else post that their mothers front loader doesnt put in enough water so Im wondering if thats what happens to mine. So wish I would have checked the reviews before buying, thought I was getting a great washer buying Maytag.This is what I wrote on their FB page: I bought a Maytag front loading washer on 5/10/16 which was delivered and set up on 5/13/16. On Wednesday 10/19/16 it stopped working, so just over 5 months from the day it was installed. I called your company on 10/20/16 for repairs, they couldnt get here until today, 10/24, so 5 days with no washer. The customer service rep had all the details on what happened and Im sure passed them along to the repair company. He ran diagnostics, said it was the drain pump which was obvious even to me, but claimed to not have one with him even though they were in stock. Cant make it back until Wednesday, so two more days with no washer. He then proceeded to tell me that the dryer had to come off (stacked on top since the washer is a front loader) before he got back, that the warranty wouldnt cover two people coming out. So Im supposed to spend more money to hire someone to come out, take off the dryer and then pay them again to come back and put it back on. I called the customer service department again and was told they dont cover installation which stacking is. She said the warranty doesnt cover stacked units, as far as I can find that isnt stated in the warranty so please let me know where that is stated in writing. So I have a just over 5-month-old washer that needs repair already (bodes well for the future doesnt it??), will be without a washer for almost a week because the repairman didnt bring the most obvious part with him (maybe wanted to be paid for two calls?) and have to pay someone else for installation so it can be fixed. So wheres the Maytag man? I am not a happy customer and will be letting as many people know as possible. Ill be in the market for other new appliances soon, will sure as hell make sure theyre not made by Maytag, Whirlpool et all.

We updated our 25 years old dishwasher, which ironically still worked, to a Maytag we bought at a BrandsMart in GA in November 2010. Sixteen months later, the unit just died. The panel would light up, but would not run. We contacted Maytag and were assigned a repairman (The Appliance Guy) who could not come to fix the dishwasher until 5 days later. Once he finally showed up, I was informed by him that the control panel for the dishwasher had two shorts in it and it would be cheaper for me to just buy a new dishwasher because the repair to this one would be $344.44. When I contacted the customer service for Maytag, they offered to let me pay for the repairs and then they would give me a six month service warranty for free. Does that make sense to anyone? I could buy a totally different brand, brand-spanking-new and have a twelve month warranty with a better product. I asked to speak with Cheris boss and got to speak with Aaron, who offered me the same spiel. Heavily scripted, I apologize that you are dissatisfied, but all we can do is give you the service warranty for six months after you pay for the repair. I asked him if he was reading a script and he replied no. Now I know that he had probably repeated these same words twenty times a day. Heres a thought, Maytag claims to be a green company, using less electricity and water, and saving the customers money and yet they are filling up all the landfills with these appliances that are not even five years old. How is that being a green company?You know how when you buy a nice new button-up shirt? The makers of that good quality shirt go ahead and sew an extra button on the inside bottom part of the shirt because they know that theres a chance youll lose a button. Well, Im thinking that Maytag should just start shipping a couple extra control panels in every box of Maytag dishwashers. Crazy idea, right? Okay, so an easier and cheaper way for Maytag to correct the problem is to stop making dishwashers. Go back to the drawing board, make the engineer who designed the control panel wash everyones dishes (as punishment and he can get help from the customer service people because theyre really doing nothing), start building the old design dishwasher that has the old switch and dial, and start respecting their customers. There, problems solved!

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

Had our house built in 2009 and the builder carry Maytag Appliances. After 3 years every single appliances start giving us problems. First the refrigerator not getting cold, got it fixed. Then the dishwasher panel, then the built-in microwave, then washing machine. Just the other day the refrigerator broke down again and I was told the compressor was bad. Really? Whats going with this company? All the appliances from this maker dont have longevity. I have 20 year older refrigerator from GE and its still working. Please do not buy this garbage... Its a waste of your hard-earned money.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

We purchased the Maytag dishwasher model # MDB4949SDZ almost one year ago. Since the beginning there has been a smell to our drinking glasses when we put drink in them...smells like boiled eggs. We have always used Cascade dishwasher pods, but suddenly our dishes were being left with a gritty feeling film on them and I had to run them under water to rinse them after taking them out of the dishwasher. This model showed on Lowes website that it has a food grinder, but it cannot even get rid of a single kernel of corn that might get left on a plate. After a load is completely washed and you open the door, there is a strong smell of detergent. If you run an EMPTY dishwasher with NO soap it creates an abundance of suds like there is still soap all in the tub!!The repairman came out and called Maytag and they ran a diagnostic check on it and it said everything was okay. He said to run a cup of white vinegar through it and I did. It didnt help. Still lots of suds being produced when I run a cycle with NO dishes and NO soap!!! He said the food grinder doesnt actually grind or dispose of small particles of food, just grease!! What?!!!! We had to PAY $92 for the service call even though it is still under warranty just because the repairman and the Maytag guy on the phone couldnt figure out why this dishwasher is a hunk of junk!!!! Also, the top rack has clips on the side to lower and raise the rack. The outer sides of the top rack will only hold smaller glasses because these clips get in the way. I hate this dishwasher so much!!! My 18 year old Kenmore ran like a charm until Hurricane Harvey flooded our house. I will never buy a Maytag appliance again!!!

This machine(Bravos XL Washing Machine) was highly recommended to me at the Home Depot by a sales associate. I broke down and took the recommendation. Oh how I regret that! This is a terrible washing machine. It does not put enough water into the machine to even cover the clothes halfway. It ties the clothes in knots! I made a terrible mistake when I purchased this!

We bought a refrigerator June 4th 2014. 6 month ago the freezer and refrigerator was getting warm. Had to call repair service, it was the blower! On Saturday 12/9/17 freezer wasnt freezing, then fridge was clicking on and off. Unplugged it, called repair service, it was the compressor. $800.00 to fix it, the same amount as when we purchased it. Repair service told us to call Maytag, he said, Maybe they will help you, would not help at all. Talked to Lori, all she said was warranty is up after a year, I then said, I think a refrigerator should last longer than 3 years! Will never buy anything Maytag again! Yes Maytag does SUCK!!!

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

My original Maytag washer lasted over 25 years (still using dryer purchased in 1977). But the Maytag model SAV 4655AWW I bought a few years ago is a piece of junk! Not long after it was out of warranty, it started making noise. Not overly loud, but noisy. Since then, though it makes such a loud noise, you can hear it 3 rooms away. It leaks water from the seals, shakes and vibrates all over the place (even when level). The rocking appears to be due to pathetic self-leveling legs they put on the back of the washer. I had to put a 2x4 on the back side of the washer to keep it stable. That took care of the rocking, but still noisy, leaking water and now it gets off balance when spinning and stops. It also wont start sometimes and you can smell it overheating. The transmission is now going out of it. This thing has been one issue after another. What is worse about it is I saw in another forum that this washer wasnt even made by Maytag. Supposedly Maytag bought? After the purchase, they just put their name on it. I bought a Maytag because of the dependability of their previous products, so Im thoroughly disappointed in their company and products. If I had wanted a washer built by some other company, I would have purchased it versus theirs. If you purchase a Maytag, you expect to get a product designed and built by them. Ill never buy another Maytag product and Ill thoroughly research the product Ill buy to replace this hunk of junk. My advice would be dont waste your money on Maytag.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

Purchased a Maytag MBF2256HEW bottom freezer in 2005. About fours ago, I had to replace the control board to the tune of $140.00. Today the fridge quit working and this time it appears to be the compressor, so tomorrow we will be shopping for a new unit. It will not be a Maytag.

After 2 years the oven didnt work. I had a repair fix it for $500 but if I wanted the convection to work it would cost another $800. Obviously not worth it. Now the oven needs to be set at 400 if I want then actual temperature to be 350. Now the latest - the racks are too small and falling! I just put my Le Creuset in the oven and the rack fell. Splashed everywhere! This happened at Christmas with my turkey. So bought the fridge - everything in the back freezes. Never ever buying Maytag again. Im guessing the Maytag repairman isnt lonely anymore.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

We bought a Maytag washer and dryer in April 2012. A few weeks ago the washer while it was spinning out, it sounded like it was metal on metal. Sears came out and said the transmission and the tub had to be replaced and the tub was created to the transmission. My husband and the only ones living in home and I sort my clothes, so I dont have big loads. I contacted Maytag, their answer was its out of warranty so we are not going to do anything for you. Anyone who buys a Maytag Washer, watch out what youre getting.

Purchase a Maytag washer in 2012 and less than 4 years later have to go shopping for a new washer. Purchased a Maytag because was under the impression that it was a good product and would last. Not true. The washer almost caught fire, just happen to be nearby when smoke started coming out from behind the washer, so I was able to turn off the machine and then unplug it and my husband smelt wires burning. If I hadnt been nearby we could have had a fire instead of smoke. I dont want to rain on anyone parade but I wont be recommending this product to anyone.

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

We purchased a Maytag Front Load Washer in April 2011. We did not purchase an extended warranty. From the beginning, it didnt seem to clean as well as our 12 year old top load Whirlpool had. Then in Summer 2013 it began to create fabric pulls in fine fabrics - tablecloths, blouses, etc. Whirlpool sent a repairman who charged $90 to tell us that the drum needed to be replaced because of a rough spot. He ordered a new drum and we understood that it would be replaced because it was within the 5 year manufacturers warranty on drums, but we would have to pay for installation. 2 months later, Whirlpool informed us they could not supply the new drum. Why are replacement parts not available for a 2 year old machine? The customer service rep told me that they would replace the machine for 15 percent of the cost of a new machine. All I needed to do would be to pick out a machine and let customer service know the model number and they would make arrangements and contact me re: payment of the 15%. When I contacted them again I was told that I would be expected to pay $508.00. That is 15% of a $3000.00 machine. It it completely unfair. Later, I was told that the first rep I spoke to must have been wrong because they dont pro rate replacements on a percentage basis. I told them that I was not interested and they have lost a good Whirlpool customer. In the last 15 years we have purchased 7 appliances made by Whirlpool. Never again! I am not impressed by their customer service.

SO SO disappointed. I thought by purchasing a Maytag washer and dryer that I was purchasing quality products. Not so. After only 3 yrs, the dryer is broken. It needs a new heating element assembly at $139 plus a visit from the technician and installation. In total, it will cost about $300 to repair. The washer is slowly going also. It takes about 2 minutes before it starts. Never used to do that. The technician told me that these do not last and that the computer is likely to go in another couple of years which will cost $400 to repair. I called Maytag to see what they could do for me. They offered the part at 1/2 price but insisted on another diagnosis even though Ive already had one. That along with their labor cost was going to cost more than anyone else. So no more Maytag products for me.

I just want to give an update on my frustration with Maytag dishwasher I wrote about on July 16. In the end, I found a DIY solution and fixed it. I wrote an instructables here: **. Not recommended if you dont feel comfortable repairing things. However, the diagnostic test at least can give you some clue whether its the control panel or control board is at fault before replacing both. Thanks.

Purchased Maytag washer Centennial Econoserve washer. It was 2 years old Aug 2013. Washer stopped working Sept 16, 2013. Of course since it had Maytag name brand, I did not purchase extended warranty due to thinking it would at least last more than several years. I called Maytag/Whirlpool. They gave me name of authorized repair in our area. So far they have come out 2 times. $560.00 later, it is still not working and they have no answer as to how or what to do. We are now into $1300.00 between purchase and repairs and still no washer. We are retired hard working people and this is really a bad way to treat consumers. Maytag customer service could care less about the situation. They just say we should have purchased extended warranty.

The Aqua lift cleaning system is a complete joke. Have had to replace oven light bulb 6 times in 11 months. Control panel is completely discolored. Expected far more from a Maytag product.

Mine is a Maytag wall oven and I purchased it because I had a Maytag Range in the house before this and loved it. It is a very accurate oven. I would rate its accuracy with the Thermador wall oven which is one of the most expensive ovens. It heats quickly and stays within the range of temperature you are using. Everything comes out just right. I like going to a Maytag dealer who knows a particular brand or brands not a large dealer of many brands. Always do some homework since brands can change over time with who owns them and who is manufacturing them.

Great stove for the price. The oven bakes good, the self-cleaning oven is awesome, the top is easy to clean up and regulating the temperature is so easy.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

I bought my Maytag dishwasher MDB7749SBM0 three years ago. After it was in one month it already needed a service call. It needed a control panel. Out of the dishwasher 4 weeks because this happened over Thanksgiving. Two months later it stopped working and needed another service call. Technician was inexperienced and another one had to be called. Out of the dishwasher 3 weeks. At this time, and because of the expense of the machine, I purchased an extended warranty. This was control panel number two. Not long after, the heating element had to be replaced. Two weeks without the dishwasher. Now, my dishwasher stopped working again and it needs a new control panel. The technician is rude but did offer the information that the moisture ruins the control panels. IT IS A DISHWASHER!!! IT USES WATER!!! I only run the dishwasher twice per week so I cant imagine how poorly it would hold up if it was run more often. I am on my third week without the dishwasher because the part is on back-order! No one can tell us when it will be in. I bought a Maytag because I thought they had the appliance market under control. MY MISTAKE! I am very angry.

I had no issues with my washer. The best thing I ever did was stop using Sabrina softener in it and made the switch to vinegar. The worst thing I ever did was think that paying $900+ for a nice washer would get me more than a year! What a joke! I started noticing small leaks when my hardwood floors started lifting and once my husband looked into this, we realized there is no seal around the top of the drum. So there is no barrier between the drum and your floors basically. Then one day we had a flood. As we watched the cycle run, we noticed that when the water was filling into the bleach and fabric softener compartments it was coming in at such a high rate, it was spilling over the sides down to the floor. So we went to the internet and found a few complaints about this, but no answers. Thankfully we found one guy who had the exact same problem and even had pictures that matched ours. Luckily a real appliance tech answered him and he couldnt even figure it out but took a guess at what I might be: the water inlet valve. But that was just a guess. So we called around to find the part and talked with a few sales persons. One was so nice to even ask a technician standing in line. And he said that there was no way this could be it. But then we decided to take a gamble. We also noticed that both compartments were filling up at the same time, but the bleach should fill during the wash cycle and the fabric softener during the rinse cycle. So it was either the $104 water inlet valve. Or the $200+ circuit board. These are my options after already spending $900+.. So we went with the valve and thank goodness it worked!!!! It is so disappointing that after a short time, this washer broke and cause more damage to my floors. It is an awful design. I bought myself the nicest front loaders for my first house. When that broke 7 years later, I bought this washer because I liked the no agitator design without the smell of a front loader. Now when this one breaks again, Im not buying another HE machine. The majority of people I talked with today said that these HE machines are breaking down faster and faster as the get better and better. I am so beyond disappointed, angry and in shock that this washer failed in less than a year and a half time. My hope is that this review will give the answers we couldnt find without paying an arm and a leg. Is this what passes for quality these days???

Purchased a Maytag dishwasher from Best Buy. We did not buy the extended warranty from BB because there is a warranty with Maytag. After 4 months of use the washer stopped working. We were unable to return it to Best Buy because we exceeded the 2 week return policy and needed to rely on Maytags 1 year warranty. It took over 2 weeks to schedule a repair and he was unable to fix it, it needed an entirely new Control Board and UI panel. 3 weeks later he returned with the new parts. It worked for 10 days with the NEW Board and panel, it has now stopped working again. We are not able to replace it due to the California Lemon Law which allows a company 3 opportunities to fix it before replacing. Next time I will purchase the Best Buy warranty so I can replace this Maytag LEMON.

Im living in a shop lot area and its near a university school. It has different laundromat stores here, and the cheapest is the one who have Maytag washers. So Ive been going there to wash clothes and as time passes, I noticed that the clothes have been getting stains after washing and these stains cannot be removed easily. Ive read reviews about clothes getting stained using Maytag washers and I cant believe that it happened to me. I dont know whats with Maytag that makes the clothes dirty/stained. I went to other laundromat stores that are not using Maytag washers. Its quite expensive, but it really makes your clothes clean.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

I bought a Maytag front load washing machine. We paid $1,100 for this machine. About a month ago, it was making a loud noise. I called them and they said were going to come out and fix it. However, our washing machine did not have a serial number. It had the model number/purchase date, etc, but no serial number. Our drier had it, but not our washing machine. All Appliances stated they could not help us until we had a serial number. We spent around 3 hours on the phone with Maytag, trying to get a serial number. Melinda informed us that we were out of luck, and that there was nothing they could do for us. She stated to call Nebraska Furniture Mart, to get the serial number. We did. NFM does not keep serial numbers. They keep model numbers, and purchase dates, but not the serial number. I called Maytag back, and spoke with Arthur. Within 10 minutes, he gave me a serial number to use. Interesting. In the meantime, I have been without a washing machine for 2 days. I have a load of wash in the machine, because now the wash machine has gotten so bad it is shorting the breaker, and not allowing electricity to the machine. This caused the front door to lock and shut down. Inside the washing machine is a load of clothes. All Appliances now has the serial number to order the parts. The parts were supposed to be here yesterday, Jan. 9th. Surprise, they are on back order until Jan. 13th. I called Maytag to see what they could do regarding me without a washing machine for over 5 days, which could turn into 2 weeks. They simply replied that it takes time to order parts, and there is nothing they can do and apologized. I asked what about me having to go to a laundromat and sit for hours, doing laundry. What about sending me out a loaner, to do laundry until you can get the parts. They again replied; there is nothing they can do.I also stated I spent $1,100 for this front load top of the line, Maytag washing machine, because of its name, and supposedly good quality. They again said there was nothing they could do. They did tell me that the washing tub, the part that we needed, was on back order until January 28th. This puts me at about a month without a washing machine. They stated they would try and locate the part, and have it sent out to my house, not the appliance company that is supposed to fix it, but my house, so that once I did receive it, I could call All Appliances, and set up the time/fixing of the machine. This has been pure hell! Maytag is a joke. I paid a good price for a supposedly good company/machine. They are doing nothing to expedite the parts. They are doing nothing to back their products. They are not even offering compensation for my inconvenience of having to go to a laundromat, or being without a washing machine for over a week, and potentially up to a month.I have been without a washing machine for over a week. I have had a load of laundry locked in the washing machine. I have had to drive to a laundromat to do laundry, which includes time and mileage. I have been informed that the parts are on back order, and now could be up to a month without a washing machine. Maytag is not offering any compensation, no loaner machine, no replacement. Instead, they are just saying, sorry, you have to wait for the parts. I would really like the VPs. and Presidents of Maytag to go without a washing machine for a week, or their families to go without a washing machine for a week, possibly a month, and see what they have to say about that company.

I am writing this because I received an offer for a protection plan today in the mail. I purchased a Maytag dishwasher on from Home Depot. I had to have the control panel (motherboard) replaced a month after purchase to failed again approx. a year later. I still own this dishwasher (MDB7749SBB) but only used it off and on 2 of the first 10 year - have not used since. Well kids are in college and my next purchase will not be a Maytag. The wife and I lost all confidence in this product.

Like others that have submitted a review, about six months ago, our then less than two year old Maytag Bravos XL washer became very loud. If the problem is the main bearing as others have suggested, its not covered under the 10 year warranty. Aside from loud noise, the washer has never performed to my wifes satisfaction. Neither has the Maytag Bravos XL dryer. Regardless of the settings, the dryer doesnt dry the laundry completely. Extremely disappointed with both the washer and dryer which replaced our 15 year old Maytag washer and dryer. We will be replacing the defective Maytags with another brand like LG or Samsung very soon.

I bought a Maytag Bravos washing machine from Lowes in Ocala in Feb 2017. It broke in March 2017. I was referred to a company called Fields Appliance in Orlando Fl. I scheduled a repair under warranty last Friday between 1-4 pm. No one showed up. No one called. I called and called and nothing. BEWARE.

I bought a Maytag dishwasher in April 2012. The electronic control panel failed in October 2013. Repair quote was $250, and there is no guarantee that the new control panel will not suffer the same consequences. My research has revealed that this is a very common problem with the dishwasher experienced by a large amount of owners, all about at the 18-month mark. I contacted the company and was chastised for not purchasing the extended warranty and was basically told, Too bad so sad. Buyer beware, do your research before you purchase this appliance. I will never buy a Maytag appliance, or any brand associated with the Maytag name.

We purchased the Maytag Bravos XL MCT washer and dryer in July of 2013 and have been completely and totally dissatisfied with every use since. We immediately contacted the store where we purchased them and were told we had to contact Maytag. We contacted Maytag on numerous occasions only to be read ridiculous solutions from a notebook that were no different than the instructions in the users manual and never worked. We had our first set of washer (with agitator) and dryer for 23 wonderful years. The washer absolutely does not work. The decision to remove the agitator and reduce the water levels is absurd. The soap does not get distributed, the lack of water causes loads of clothes or sheets to get rolled up into tight balls with no hope of being cleaned, and the spin cycle is so powerful it rips your clothes apart unnecessarily. The dryer is smaller than the washer and cannot handle the same size load the washer can put out and typically requires more than one cycle to complete a drying. All in all this has been the most painful experience we have ever had with any appliance. We are completely dissatisfied with both the store where we purchased these units and the complete and total lack of response from Maytag after requesting either of them to take back these units or make some equitable adjustment so we could purchase different units. We have reached a point where we will most likely store these Maytag units in the garage and purchase a new washer and dryer, being forced to accept the financial loss.

I purchased the top model Maytag dishwasher, and within four uses, I noticed major water damage to the side of my cabinetry. I pulled out the dishwasher and realized it was coming from the side unit where water enters the tub. These things happen, and I phoned their customer service department expecting this unit to simply be replaced, being that it was less than a week old, and that I would have been left a satisfied customer. They were willing to send a technician over to try to fix the problem, but not replace it. I now have to replace my cabinets, and maybe even my granite as it may be damaged in the removal process. I am not asking them to fix that even though the damage was caused by their dishwasher, but a new dishwasher, I did expect them to cover. Their customer service stinks, and I suggest to anyone that if you have any problems with a new unit, the best thing to do is return it to where you bought it. Im sure they will gladly give you a new unit and send the bad one back to Maytag. Dealing with Maytags customer service is the worst thing you can do. They do everything in their power to not replace it. Instead, theyd rather lose a customer for life. Whats sad for them is that Im a builder, and I usually build approximately three houses per year. Thats a lot of units theyve lost sales on over a simple replacement of a dishwasher. Its not a good way to do business. The bottom line is, stay away from Maytag.

I purchased a Maytag built-in microwave and oven combo in 2005 for my newly built home, but I did not move into the house until 2008. So the appliance has only been used for 3 years. The microwave stopped heating after only 3 years of use, which was for microwave popcorn mostly. I also purchased, at the same time, a Maytag cooktop. The knobs had to be replaced, a dishwasher, a rack and utensil holder had to be replaced and a washer dryer that doesnt work properly. I also purchased a side-by-side refrigerator which is okay so far. Im very disappointed in their appliances and they were expensive.

Eight years ago we bought all new top-of-the-line, stainless steel refrigerator, double oven range, dishwasher and microwave. All began malfunctioning within the first year: *The refrigerator began to make a loud rattle and the digital control pad needed to be replaced -twice within the first year. Within the next year the compressor had to be replace. *Dishwasher electronic control board was replaced twice, broke again and is still broken. *Microwave door handle broke off, and turntable motor broke.*Range burner ignition system only works on two burners and the shelf for the top oven does not fit -*Maytag refused to replace. Also, after using self-cleaning feature the lower oven still fills the room with smoke so it has been used very little. So, how much worse could it be? I had faith in Maytag-thats why we bought the brand.

The washer and dryer were purchased together as a set 4 years ago in 2010. There have been times where I actually had clothes come from the washer completely and partially dry due to lack of water inside the washer! It fills based on how many clothes are in the washer or capacity that it senses. I have had so many clothes dry washed and torn up due to its use! If you set the washer to the wrinkle control position it does not go through the last rinse and spin cycle, you must reset it to the rinse, drain, spin cycle again in order to finish processing that load.It has already thrown its belt 2 times! Which my husband had to fix since we could not get in touch with anyone at Maytag who knew what we were talking about! If change gets stuck inside the washer bin in the little groove in the tank it is very difficult to get out, Im sure everyone has washed a pair of pants with the change still in the pockets, yes I know this is user error but if you dont know the change is in the little grooves because you cant see them, it stops the washer! So be sure to search this every time you do laundry!The dryer has a mind of its own! Sometimes it will finish drying your clothes, sometimes it wont finish the time set! Theres no reason just doesnt finish! There is so many reasons I will never purchase this brand again. Ive run out of room and patience. My clothes look like Im homeless!

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

I purchased the Maytag Bravos XL MVBW755DW Washer and MGDB755DW Dryer in July 2016. Shame on me for not making my complaint sooner. They offer the Tide Pods for use but they dont completely dissolve and leave a residue/stain on the clothing. I have to wash everything on Deep Water Wash just to try to get them to come clean. Clothes will come out dry in some spots, they will have fabric softener stains on them, the pre-treated stains are still there once washed. Lint residue will be left on just about every piece of clothing. The fabric softener/detergent dispensers left side is rusting and I have to pull it out and clean it once a week. I cant get to the track on the inside to try to clean it and soon that will deteriorate and the dispenser will no longer slide into place. If I could attach pictures I would. Now moving on to the dryer, it dries clothes great. My only complaint at this point is that when the cycle is getting ready to shut off it sounds like a jet engine and rattles terribly. To sum this up, I called customer service this morning. They said nothing that I am explaining to them sounds as though it is a manufacturers defect. They said they will send a tech out to review at a fee of $99.95 plus the cost of any labor associated with the repair. They did however offer to pay for the parts. Now my question to them is if none of my issues are a manufacturers defect then why would you offer to pay for the parts? The unit(s) are no longer under warranty... Think twice, gather as much information as you possibly can prior to making a major purchase. I DO NOT RECOMMEND THIS PRODUCT!

Echoing the sentiments of others on this site, I am deeply disappointed in Maytag brand appliances manufactured by the Whirlpool Corp. When, for the first time in my life, I was able to buy all brand new kitchen appliances, I didnt even consider any other brand but Maytag. This was based on many decades of using Maytag products and watching my mother use them. I come from a big family so our appliances got used hard, and the Maytag brand ones worked year after year, decade after decade with little or no maintenance. To put it quite frankly, my new Maytag products are junk. I could supply a whole laundry list of problems but, in the interest of space, will just tell about the latest. A couple of weeks ago the fake tin foil paint on my oven and burner knobs just started falling off, revealing cheap plastic underneath. When I called Maytag to complain, I was asked how I clean the knobs. I told them that when I clean the stove front I remove the knobs and drop them in warm water with a couple drops of Dawn dishwashing liquid for the few minutes it takes to clean and polish the stove front, and that I had been using this same procedure for 2 years. The rep. hemmed and hawed awhile and then went away to consult her database. When she returned she told me that one is not allowed to soak the knobs per the manual, and therefore she could not offer any help. She then generously offered to transfer me to the parts department, where the rep. informed me that replacements would cost $70 EACH, thats a total of $350 plus shipping for 5 cheap plastic knobs. WOW! What a deal! I tell everyone I meet NOT to buy any Maytag branded product, and to apply extreme skepticism before considering any Whirlpool product. (BTW - the last certified Maytag appliance repairman to come & fix one of the appliances essentially admitted they are junk.) Model #: MGR8775AS SN: R32810432.

I purchased all Maytag products for my new home three years age. The dishwasher stopped working 13 months after we purchased it. Since the home was under renovations for the first month, we only actually used it for 12 months. When I called Maytag, they told me that it was either the control panel or mother board and that they could not do anything because the warranty was only for 1 year... and didnt offer me anything to make good on this...NOW three years later, my microwave is displaying error code SE.. control panel is bad. Now I have not had a working dishwasher for two years and this just added salt to my wound. I called Maytag furious that this keeps happening with new products. The only thing they would offer to do is for me to purchase an extended warranty at $350.00 and they would have a repair guy fix the microwave. A brand new microwave would cost the same thing???? They flat out told me that there was nothing that they would do for me, and that they were not going to fix it for free.I filed a complaint with them and never heard back from anyone at Maytag. It seems strange that the control panels craps out within one to three years on two of the four Maytag products I purchased. I WILL NEVER BUY MAYTAG AGAIN... I went back to Home Depot and told them that MAYTAG has LOST me as a customer and that I purchased 4 major appliances from them and two stopped working with in 1 to 3 years. Home Depot was shocked and gave me $100.00 towards a new dishwasher. And I did not buy a Maytag.... I still do not have a working microwave... But when I do have the money to replace it, it will not be MAYTAG. Looking online, I notice a lot of the same complaints about Maytags control panels...... Could it be a scam on Maytags part???

I bought a Maytag dishwasher (model #MDBH979AWS3) from Home Depot on July 2010 and had it installed. After 2 weeks, I found water leaking into the basement. The installer said rubber gasket in water line de-laminated and caused leak under the dishwasher and flooded the floor to basement. Product defect and water damage covered by Maytag insurance. Now Feb 2012, about 1 1/2 years after buying, the touch panel controls dont work. I called Maytag regarding any control panel recall and they said no and its out of warranty. The advice given was that they can send out a serviceman for $269 to fix with parts, labor and one year warranty. It seems like planned obsolescence. Dont buy a Maytag.

Had previous Maytag for years. Good, reliable, easily repaired product. Cycle sequencing very recognizable. New washing machines are ridiculously designed. Neither you nor the repairman have any idea what the cycles are or if they are even working as designed. Many cycles start out trying to wash with little or no visible water in the drum (top loader). The clothes come out tied in knots. I now wait for the agitation to start then pause and add water for three to five minutes then restart. What a nuisance. I have called customer care many times and they are courteous but not very helpful. This machine is an engineering nightmare. If I were in charge I would retire the people who dreamt up this contraption and get back to something reasonable before all their credibility is lost FOREVER!!

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

The stove functions are excellent and the temperature of the burners and oven causes the food to cook even. However after about 6 months the heat from the burners causes the coating on the stovetop to burn like its baking and it cant be cleaned. Now the coating around the burners is horrible and burnt.

Bravo XL - This is the worst washing machine I have ever purchased! Loved it at first but after a year or so we couldnt wash a full load without error messages. Then we couldnt even wash one pair of jeans without an error message. Called to have it repaired and $300. Later the bearing was replaced and the washer worked wonderfully once again. Less than a year later and we are back to having a non functional washer. Cannot wash anything without the error message. Customer service is absolutely no help. For such an expensive washer and supposedly a good brand, this machine is a real disappointment.

I have had this dishwasher less than 2 years, Maytag model # MDB7749SBM2. The control panel started acting up, it would not let me select a wash cycle, it would select its own and I could not change it. After reading these reviews, I took off the control panel and discovered the wires which are encased in a plastic were all darkened and messed up. I will try to replace it on my own but if I have to I will buy another brand as this dishwasher hasnt really cleaned my dishes all that well to begin with.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

We bought a Maytag Dishwasher Model # MDB4709AWW4 about 2 years ago. Complete piece of junk. Just spent $350 on a new control panel. We called Maytag and they told us that our model wasnt under the recall for this issue. The old belief about the Maytag repairman not being busy is a lie. Avoid their products. They are poor quality.

Maytag dishwasher model MDB7759SAB, 1 year old and control panel will not work at all. Maytag site does not recognize model #, got part numbers off parts and cant find the parts. Looking for control panel, cant find black one and others are back ordered for weeks. After reading other peoples problems, it seems Maytag would correct the issue.

I have filed a class action lawsuit against Whirlpool for their faulty control panels in their Whirlpool and Maytag dishwashers. Please contact my attorney, Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 and let them know if you own or owned a dishwasher with control panel failures.

I waited my entire life to age 47 to purchase a brand new matching Maytag washer and dryer. I was thrilled. That was August of 2012. 3 years and two months later, the $800 dryer (MEDE201YW) loses the entire control panel and Maytag refuses to offer any assistance. I deliberately purchase Maytag with its stellar reputation, an American based company only to be more disappointed in the product and the company than in any other appliance Ive ever purchased.

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

Bought a maytag dishwasher 04/12/2013...have been thru 2 control panels...Now installing a third...washer works great except for that!!! Model mdb8949sbb0.

Maytag Bravo 300 Quiet Series - Bought this Maytag 5 years ago because Ive always had good experiences with them. After 3 years it started making rattling sounds so we had someone come out and fix it for around $275.00. 2 years later its still rattling, leaving black grease marks and putting holes in the clothes. Will not complete cycle unless it is unplugged, reset and plugged back in. I give up, I just bought an LG. I will never buy another Maytag washer again, still have the matching dryer though.

I bought my Bravos washer (Maytag Bravos Model # MVWX700XL2) back in 2013. Worst mistake ever, First off the clothes never came out clean, regardless of how diligent I was following the directions on how to use this particular type of machine. Secondly, it started going off balance for every load if I put more than 4 pieces of clothing in. 2 months after having it recently repaired AGAIN for not spinning and going off balance, it is doing it again. It is only 4 years old! I bought it for the Maytag reputation, but now I am doubting that reliability.

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.

My Bravos 300 series is 3yrs. Initially it occasionally shredded an item. With 4 kids I chalked it up to wear & tear on the clothes. Its now ruining items almost every wash. I now wash much by hand. Cant wait to afford a new one.

I bought this POS and paid almost 1000. Out the door with tax, hoses, delivery, etc. And it is by far the worst most useless pile of crap I have ever purchased. It just does not work!!! Its a washer that does not wash. It uses enough water to wash one sock and that still comes out stinky.. All my clothes no matter what cycle I use including deep fill power wash or if I add my own buckets full of water to the 1.5 hour wash cycle still come out dirty, stinky, stained and caked with detergent...Hey Maytag heres a hint. You need water to wash clothes and you need agitation to get out the soil, the dirt, the sweat, the stains, the stink and your washer does none of that. In fact I could get my clothes cleaner if I out them in the bath tub and swished them around with a broom stick for 3 mins. How could you go from the loneliest man on earth to the biggest scammer on earth by producing this boondoggle... P.S. Its only me and my wife. We are retired and our clothes are not even that dirty... Its just common sense. No water no action no clean. Ill never ever ever buy anything that says Maytag on it ever ever again and you can bet your life Im telling everyone I know this story.

I bought the Maytag Bravos Series 300 Dryer in 2009. In September 2011, the dryer wont start. I called Maytag. They basically said were on our own. It only lasted two years. What happened to appliances that lasted 10 years? I will never buy a Maytag dryer again.

I paid $958 + tax for a Maytag Bravos washing machine in August 2008. I live by myself, so the machine is not overused. Nevertheless, it began to sound like a jet airplane during the spin cycle. And then in May of 2012, it failed with error code F51, catastrophic failure. The machine was not even four years old. I called a certified Maytag repairman. In less than 5 minutes, he told me the cost to repair would be about $900, and then he charged $115 for the service call! A call to Maytag resulted in Im sorry, there is nothing we can do.

Maytag Bravos XL - I have always loved Maytag and never had any problems. In Feb we did some major remodeling with new flooring in our laundry room. Decided to buy a brand new washer and dryer even though our 10-year old Maytag washer and dryer worked perfectly fine. After looking at Home Depot and Lowes we first settled for a Samsung W & D but before it was delivered we shopped some more. After doing some inquiring we decided that we wanted to stick to a long trusted W & D line so we chose this washing mashing and matching dryer. From day one I decided I did not care for it. I found if I put too many clothes in that they did not come out clean. Any dark pants would come out with what looked to be soap or softener stains and would have to rewash 1 or 2 times. Now I can only put in about 4 pairs of pants to wash. I have been cleaning it once a month as the manual says to do but yesterday I noticed a terrible odor coming for the washer. I could smell it out in the hall. I did the cleaning again but still smell it. Now after searching the internet I find a video that shows the problem is mold under the drum. No amount of Affresh or bleach is going to clean something UNDER the drum. It is not my job to have to take this apart every few months and clean out mold and moldy water. Sounds like this problem has been going on for a few years and this should have been fixed long before this. I wish I had my old faithful washer and dryer back. Maybe I should have stuck to the Samsung washer and dryer.

Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.

Eighteen months after purchasing the Maytag Bravos, I had to have the motherboard replaced. Maytag offered nothing except a list of names for repairmen in my area. Now another 18 months later, the washer gets out of balance (this is a self-balancing machine, supposedly) at least three or four times for every load. Since it is all electronic, you cant select a spin cycle without the machine adding more water into the tub. Again, this does not self-correct the out of balance problem. Trying to balance the cloths several times during a wash cycle extends the length of time it takes to wash one load on average two hours. Maytag offers no customer service or customer support. Im sure their call center is not located in any part of the United States. I will never purchase another Maytag appliance.

Maytag washer has increased my water bill; it was supposed to be energy efficient! Also, the washer will not wash a blanket. Sensors will move a large item to one side causing an uneven load which then causes numerous extra fills until stopped manually. I was told to add more items! A blanket barely fits in the tub. I had to invest in lint rollers since the rinse cycle is inefficient. This washing machine is useless. I should have stuck with Kenmore.

Since the day the Neptune washer and dryer were installed, the washer has given me nothing but problems. It vibrates so badly and dances all over the floor.I have had the repairman over at least seven times and, now, it is out of warranty so I am spending my own money. The last service man was from Hurst Appliances in Regina, SK. He removed the pedestal to see if this might be the problem. He also sold me some foot pads for $50 that he said might help the problem. However the machine is still vibrating and the terrible mold smell comes out of it as well. I am thoroughly disappointed in this product. I will never buy another Maytag product and tell my friends not to as well.

I am a Baby Boomer... just like so many of us, I watched those lonely Maytag Repairman television commercials. Yes, silly me I purchased our top loading Maytag Bravos XL because of the brand name and because the machine was large enough to wash our bedding. Well, like so many fellow purchasers have found, this machine does not get the clothes clean and leaves soap spots all over the clothes. Its embarrassing. Additionally, there is that funny smell after the clothes come out of the wash. Well, Maytag has really done a number on us all. Kudos to their research & development department for creating a washing machine where the clothes come out dirtier. Has Maytag thought about a RECALL? I will tell everyone I know to NEVER buy a Maytag.

Need to keep cleaning washer otherwise it leaves white marks on clothes. I used vinegar but that didnt help. Used the wash cycle and that didnt help. I found a washer cleaner and it works great. Overall performance of washer is fine but I would be hesitant on purchasing another Maytag Bravo washer only for this reason.

Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

My Maytag washer is only three years old and the control panel completely went. Not only did it cost me the service call, they want $360 to replace the control panel. I called Maytag/Whirlpool to see if they would help with the cost of the part. I am 60 years old and the only one who uses the washing machine. It is not beat up. Maytag would not offer any solution at all and refused to even pay for any part of the control panel. They said it was really my tough luck for not having bought the extended warranty. When you spend so much for an appliance, you do not expect it to only last three years and you should not need an extended warranty. I am so disappointed and I will never buy a Maytag or anything from its parent company Whirlpool.

I bought a Maytag electric stove steam lift oven 2 years ago, I regret it. I baked a pie, and used the steam cleaning, it didn’t clean, my oven is still dirty. The top of the stove is not easy to clean and scratches very easily. It’s not my first stove, different brand, and I never had problem like I have now. I should have stayed with the brand I had before. My other regret, I should have read the reviews.

So we purchased a whole package in sept 2014 for our newly constructed home. In Nov we received the CO and thats when everything was finally professionally installed. After its first wash the dishwasher broke and there was a flood in the house and soaked 20% of the newly installed high quality cabinets. We cleaned up everything and called Maytag to have someone inspect it to see what needs to be fixed. The gentleman came about a week or two later and said that the machine isnt worth fixing and to try to get Maytag to replace the whole machine, but he still listed all the parts that were needed to fix it. We tried calling Maytag and said what the repairman said but they said he must fix it and they will not provide a new one. So we wait for the parts and no one calls us. We follow up with Maytag and they say theyve ordered the wrong parts so it will take longer. We try calling the repair man and he doesnt call us back.Then call Maytag again and get them to call the repairman to see why he doesnt answer us. They told him to call us twice and every time he tells Maytag that hes called us and we dont pick up. So we tell Maytag hes lying, the repairman hasnt called us for weeks and Maytag doesnt give a **. And seems like this repairman is freaking lazy and doesnt want to work, even if hes paid for it. You know whats happening now? Chargeback! Thats right Maytag, screw you. When I do another house I will never buy Maytag again! Horrible service and a very defective product. I thought we were paying for quality!! They lost a customer that is faithful and doesnt mind paying extra. Hope everyone can take this into consideration before buying. I wish I wouldve seen these comments before...

My Neptune Maytag pair have been dependable. Great features. Now at 20 yrs old still kicking. Washer-front loader now has issue with fab softener going into wash correctly. Could be build up? Trying to self-fix. Very gentle with washing fine things. Hope I can keep going with them.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

In the last 6 years, Ive had a Whirlpool dishwasher that the motor seized due to poor design and overseas Asian motor builder (3 years of normal service). I cleaned the motor and it seems to barely work another couple of months but the design and manufacture process was garbage at best. Thinking I would go with the best produce MAYTAG (Old commercial about repairman having no calls), only to find out that it too was bought out by CRAPPY WHIRLPOOL and it too lasted a couple of years with cheap MADE IN CHINA electronics!!! Thats why we are the laughing stock in the world as far as products.I remember the days of where built in the USA was the best of the best, now with selling our great nation down the toilet so some Wall Street Commie can make his/her biz-zillion dollars and sell this nation down the toilet. Maybe they need to go down to Arlington and see who really has paid the price for their luxurious life-style!!!

I am 86 years old and have happily owned Maytag washers for many years. I just recently purchased the front loading model for ease of access. After using it for sometime, I could not be more disappointed. The clothes come out smelly, stained and gray. I tried using affresh washer cleaner on hot setting and the tablet did not even dissolve. There is black mold growing and must be cleaned constantly. I am so sad that my favorite company has let us down. I cannot afford to buy another washer so I am stuck with this lemon!

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

I have a bearing going out. The Bravo washer makes a terrible noise. Now, they tell me I need a new tub/bearing. This repair will cost me more than $250.00 plus service calls. This is the second repair that I have had on this machine. It is only 4 years old. I use it twice a week. I will not recommend Maytag to anyone and I will never buy another one. They should check the internet for complaints and realize that there is a problem.

Maytag Dryer model # MEDC400BW. I purchased this dryer in March 2015 the fuse went out in August. It is now November and it is out again! I have been buying Maytag since I left home at 18. I am 62 now, so I have been a loyal customer because Maytag was a great product. Not anymore since Whirlpool bought them out! You have to call them to schedule a technician and then it can take anywhere from 1 week to 3 depending on when they get the parts because they have to order them, and nobody else can come out to work on it if it is still under warranty! This is so lame and just not right.

I bought a new Maytag dishwasher installed by East Town Appliance in Wautoma, Wisc. They installed it and ran a full wash cycle and it worked fine. After they were finished, I got all my glasses out and put in their dishwasher all excited to get them clean and sparkling. I started the dishwasher, put on a coat to check my birdfeeders on the deck where I was standing in front of the patio door. I heard water running suddenly. Turning around to see water gushing out of the bottom of the dishwasher. I called East Town back and had the installers return immediately. The pump was stuck open. I called Maytag about what happened and they said they wouldnt pay for the floor damage because it was already installed and to call my insurance company which I did. They went after Maytag and won but I had to pay $500 insurance deductible. I will NEVER buy anything by Maytag again.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

This is a Maytag Neptune MAH8700AWW. This machine has been repaired a couple of times already and it has a will of its own. When it goes into that fast spin cycle that will kicks in and it starts moving. I wonder if someday its going to attack me. So, last Friday night we put a load in and it went into that fast spin cycle. It was making a noise like an elephant in labor so I looked in the laundry room.... Clouds of smoke were billowing out of the top of the machine. Our house will filling up with washing machine smoke! My husband stopped it, but I think it was a gnats hair close to bursting into flames. He looked into the front of the machine when the smoke dissipated and the entire gasket was in shreds. No more Maytag. Never. Im done.