When we first purchased our fridge, I was super excited. I have read the numerous reviews regarding ice in the bottom and the noise. Ours is noisy also. Nothing I cant live with. Now ice on the bottom. That doesnt work for me. A friend of ours told us the drain was plugged. Not that the doors needed to be replaced, nor does it need gaskets. All you need is a hair dryer and a man like mine who can build or fix anything (honest to God that is the truth). He took the drawers out and then removed the door to the freezer. In the center on the back of the fridge is a drain hole. Aim a hair dryer in this spot and it will melt the ice which is plugging the drain. Ours took about three years to have the water in the bottom issue. Since we have now seen where the drain hole is, there would be no need to take the door off and the drawers out. Now, one other preventive measure. Take off the lower back plate of the fridge. At the beginning of the drain hose is a rubber nipple. There is barely any room for the water to drain. We cut the end of the nipple off in order to make the water drain better and less likely to stop up. We just snipped a bit of the end. The reason it is designed like that is to prevent air from coming into the. Just a small snip. I hope this may help some of you. Tell the Maytag repairmen how to fix it.

This is the best microwave that we have ever purchased. I especially like the baked potato choice. Its also very easy to use and clean. I would definitely recommend it.

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

Worst washing machine I have ever owned. Read all the other reviews and concur with them. We get pin sized holes all the time. Brand new shirts yesterday and they have black stains all over them - not the first time either. Inside of stainless steel tub looks clean. Where do the black marks come from? Last Maytag I will ever buy!!

I purchased the most expensive stackable set available. After 3 years the Maytag Front Load Washer is dead. Wont turn on or receive electricity. It stopped in the middle of a cycle so I have an entire load locked inside. A repair person came out and confirmed $600-$1,400 to replace computer electronics. Right on the front of the machine, there is a shiny tag displaying 10-year Warranty. I live chatted with Maytag. Only the drum and some other ridiculous part is covered. She told me to call the 800 number to speak with a customer rep. After trying 2 times and being put on hold for over a half hour, I hung up. I WILL NEVER BUY A MAYTAG AGAIN!

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

My model has 2 ovens which I love. A smaller one & a regular sized one. It also has a cooktop. The cooktop always has “marks” on it from the pots & pans. No matter how careful we are, the pots leave marks. We even bought new pots & they leave marks. Something that we do like is that 2 of the burners have “select a size” so these burners can be used for small or larger pots.

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

The washer is very aggressive - it will tangle the clothes and actually tear them if they are thin. There is little control with the speed or water temperature or with the amount of water for a load of clothes.

We purchased this Maytag top load washer less than three years ago. Spin cycle stopped working and repair for new actuator motor is $240 (machine cost $500). I should have read Maytag’s reviews before we bought it (averaging about 2/5). Living on name - don’t buy one.

I will NEVER get another Maytag product ever again! My not even 1 year old washer broke and I have been waiting almost 2 1/2 months for a part to be replaced. My partner and I are nurses working on the front lines during this COVID pandemic and I can’t even wash my scrubs at my own house but instead I have to go to a damn washateria. The “supervisor” told me 2 weeks ago that if the part is not in by today, 1/27/21, that a brand new washer will be sent to me. Well I call today and the people I spoke to denied any recollection of this information. The “supervisor” stated that she is “documenting all of the information” so when I called back I would not have a problem. Once again I have been lied to and wasting my breath and time. The customer service has been TERRIBLE and I cannot believe that this was once a “reliable” brand! Clearly this brand is unreliable and the personnel is also unreliable. NEVER AGAIN WILL I BUY A MAYTAG! Save your money and buy a different brand!

Neither appliance (Neptune dryer and washer purchased in 2006) was worth the price paid. The dryer drum actually cracked and the washer repeatedly gets hung up on 3E. I called about the dryer and got an Oh, well response. “We dont know whats happened to that dryer.” What happened to both appliances is that they were used for their intended purpose. I do laundry for my husband and me. Is that too much for a Maytag? Customer service is equal to indifference. So much for Neptune. And thanks for standing behind your products. What is the life expectancy of a dryer drum anyway?

Purchased the Maytag Bravos XL washer and dryer in January, 2014. Today, 5/16/15 (less than 1 1/2 years later) the repairman tells me that the cause of the loud noise in the spin cycle is bad bearings. Only a 1-year warranty on the machine. I have never purchased extended warranties on appliances so this will cost me $400! Or a new washer since this is more than half the cost of the new washer. This is bad business, Maytag. Ive been a loyal Maytag customer for years but I think Im heading to Speed Queen with their 5-year warranty unless youre going to give me a helluva deal to keep me. Grrrrrrr.

I purchased a Maytag fridge with a freezer on bottom. As you know there are many complaints regarding ice build-up in freezer causing leakage out onto the floor. I will not purchase Maytag again. For 3 years I have fought the ice buildup and it has ruined my floor! Poor design - should have been recalled!

I have on the Maytag dishwasher for about a year. Is very quiet, the dishes are not clean. I called three repair guys from Maytag. The first time they replace the pump. Second time the guy said he just had a designed machine is no good.

If I could give less than one star I would. I purchased a Maytag range in September 2021, 33 days later the oven went out!! I have been fighting trying to get it repaired for months!!! The parts are not in, the parts have been shipped, oops we forgot to ship the parts, the technician is on vacation. You name it, I have heard it. After the phone call today, it looks like I will still be without a range at Christmas!! This is totally unacceptable. I purchased a Maytag because I assumed it was a good brand! Do yourself a favor... Never buy a Maytag or Whirlpool Appliance. Its not worth it. For the range to only work for 32 days is just plain Wrong....

I purchased a Maytag refrigerator in November 2016. It is now the first week of June 2017 and the ice dispenser no longer works and the door alarm goes off incessantly and intermittently all day and all night. I am so sick of being woken up by the alarm in the middle of the night. I reread the manual and ran through the limited troubleshooting to no avail. I called customer service, sat on hold for a half hour, and scheduled a service call. As an interim stopgap for the pull-my-hair-out alarm issue, the operator suggested I disconnect some wires, as there is no off button for the door alarm. I wasnt dumb enough to do that and void my warranty. Best part of the call was when the operator offered to sell me an extended warranty. Well see how the service appointment goes, but I have a feeling this is the last Maytag product I will ever get. I am very curious about the lack of product recall as my research unveiled hundreds of complaints about the exact same issues I am having. Why does it seem to take a class action lawsuit before a company fulfills the promises in their advertising? Model number: MFI2570FEZ01 Purchased from Home Depot in Nov 2016 for $1,230.

My Maytag refrigerator Model MFX2571XEMS has to constantly be defrosted due to ice accumulation in the bottom of the freezer. If not defrosted, water leaks out onto our hardwood floor. Maytag will not do anything to resolve this problem. We were told by a repairman that we have to defrost it manually to fix the problem. Yeah at least every 2 weeks. What a rip off.

This machine may save water but I spend more time and money getting out the severe wrinkles it creates. I use my dryer and iron much more than with my previous washer. I never thought a new washer would make wash day more difficult.

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

My Bravo washer does NOT clean my clothes. I have tried many detergents. I have to pre-treat all spots with dish soap and run hot water over and then rub the spots out. This was the only recommendation given after consulting with Maytag. I have to pre-soak my clothes in a pail of water with detergent. The water is brown. My clothes are dingy, spotted and have bleach spots. I am very careful so this is not from pouring into the bleach dispenser. Maytag was the reason I purchased this washer. Never again.

My oven smelled for weeks after being installed. The first time I self cleaned, the oven stopped working and the door remained locked. It took weeks to get it repaired because we needed a part that had to be ordered. The second time we self cleaned, the oven smoked, set off smoke alarm that had to be disconnected, the control panel bulged, and the door locked. It was Sunday. I wrote a nasty email to Maytag. The service man who came Monday could not unlock the door, and said he had to order a part and would return the next Tuesday if the part arrived.Next, I had warranty issues. I had to get a copy of the purchase receipt from Home Depot to prove that the oven was still in warranty. Out of the blue, my phone rings on Thursday and it was Joe ** from Maytag in Michigan. He had read my email, said he was sorry for all the problems, and if I did not mind waiting 2 to 3 weeks, he would send me a brand new oven, would have it installed, and would have the old oven sent back for inspection. I did not mind (although there is only so many things that can be grilled or you can bake in a toaster oven). Three weeks later, I have my newly-installed new oven with its new, year-long warranty. Thank you Mr. ** and Maytag for the great service.

Bought in July 2014, third service call already! To replace my 6 years old Maytag Centennial thinking I was doing a good thing to upgrade to an HE... HA! Jokes on me! Washing machine: Water level. How can you wash clothes in 1 inch of water??? Noise. Very noisy at every cycle. Shakes and easily unbalanced. Clothes are still dirty after wash (obviously if not enough water). Dryer. Noisy with sporadic blower sound (like a plane taking off - high pitched). Three service calls in 6 months??? 2 calls for cable suspensions and now waiting over a month for the tech to change the drum completely. Good thing that I took an extended guarantee, for an extra $300.00!! After Ive read the over 400 complaints about this product, I really feel like I got screwed! My last Maytag EVER!

We bought a New Condo, all New Maytag appliances with a 10 yr. warranty, the microwave is a built-in model. I cant believe weve only been here a year and eight months and it just stop working. We use it for heating and short timed cooking like 1 to 2 minutes. I would think a name brand product would last a lot longer than this. I had an off brand microwave for five years before the condo. A couple of times the microwave door didnt close, I thought I forgot to close it. But after reading your reviews I now realize its one of the defects of the product. I called the Maytag company, they informed me that if a serviceman come out to fix it, it will cost me $180 until they can determine if the cause is something covered by their warranty??? The Home Builders bought Maytag junk and passed us the cost, now Maytag wants me to pay to see if their junk can be fixed??? Wow!!! This is unbelievable!

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

I bought a Maytag stainless steel refrigerator w/ freezer on the bottom. Since 6 months fridge being in my house I started to have problems, rust on the doors, water coming out of the bottom, freezer door got stuck w/ ice and couldnt be opened, butter, eggs, milk can be frozen one day and the next they have mold and bacteria because of the changes in the cooling system, among my problems. And what? Well yes thank you so much for the guarantee Maytag has in Puerto Rico, IT SUCKS! They been in my house more than 5 times and nobody really says whats wrong. They supposedly change the computer, still having problems, and this was done after more than three times visits from Maytag guarantee. Im still paying for the damn fridge and DO NOT HAVE A RELIABLE REFRIGERATOR. Im wasting too much food, Im obligated to buy food almost every day cause Im scare to give something that may be bad and my family will be food poisoned. Whos going to pay me or my family if something happens. Maytag is still running falsely commercial ads and somebody MUST STOP THEM. This appliances are not free or cheap. PLEASE help us because Ive learned that Im not the only one having problems in Puerto Rico w/ Maytag. Also I believe Maytag is using technicians not ruled by the government of Puerto Rico and thats why the service is horrible.

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

I received my Maytag dishwasher in November of 2013 from Home Depot (It was a month overdue the expected delivery date). It was installed by a certified electrician/contractor. By February of 2014, the control panel had to have its first replacement. It is now July 2014 and we are having the repairman come out to replace the third control panel this Monday. Supposedly there was a recall on the control panel and the one replaced less than a month ago was the improved/repaired one. We are beyond frustrated. I too sought Home Depot for help after the first repairman they suggested charged us almost half the cost of the dishwasher for his repair. I have already sunk over the price of the product into repairs. My Maytag dryer broke last week as well. Someone needs to get involved with this situation, perhaps a contact to the media? I think we are all being scammed and deserve refunds by Maytag for the dishwashers and our repair costs.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

Have a Maytag refrigerator, less than 2 years old. Water is leaking from top of the inside of the refrigerator, presumably related to water dispenser, unrelated to filter, and dispenser still functions. In shock, Ill have to pay an additional $347.00 to Maytag for an additional warranty if I want them to remedy this!!! Model # MFT2672AEM10. Buyer beware! Upset that such a new refrigerator would have problems - more upset that the company is making no efforts to make it right without charging more. The refrigerator was not cheap in first place. Also the time spent to have someone come out... Maytag advertises repairman boredom.... Never had another problem with other appliances unless they were much older!!!

The Neptune Front Load Washing Machine I purchased in December of 2007 started sounding like a jet taking off, about three months ago. The noise has become unbearable. The repair person said that the whole drum needs to be replaced and it is not worth fixing. Are you kidding me? This was an expensive washing machine and now we have to get a new one? We cannot afford to get a new washing machine. We need an explanation of why this would happen and from the other complaints I have read on the Maytag website, we are not the only ones. This is the second time something has happened to this washer, the first time, it was under warranty (only a few months into the purchase and the pump was bad and was replaced). What is the company doing to help people with this faulty machine?

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

This is just a heads up to anyone thinking about purchasing the front loading Maytag Neptune washer and dryer. We spent $1900.00 on these machines and have had nothing but trouble from them. I will never purchase a Maytag or now, Whirlpool appliance again. As to the rating above, if I could post negative 150 stars I would. I have spent as much in repairs as the new dryer cost.

I purchased a Bravo Washer and Dryer from Home Depot. The Maytag Bravo washer and dryer we purchased from Home Depot did not work from the beginning. Before I called Maytag, I tried for several months to redo the way I was loading the washer and dryer.I tried several different settings however, the clothing keeps coming out smelling like it is still worn. Spots are in the clothing that normally comes out with a washing (with my prior washer). The clothing just does not get cleaned and it gets so tangled that it has ruined some of my clothing. There is clumping of the detergent, even though not a lot has been used.I had the repair company come out three times for both the washer and the dryer. They have checked and no errors codes where found. One gentleman told me again to redo the way I load the washer and the dryer. I have done it so many times, but I tried again and even purchased little dryer balls. It made no difference.I called Maytag again and was told they would have to have another company come in and do a second opinion. The person came and said that he agreed that the washer should be able to wash and the dryer should be working correctly. He recommended that a possible problem with the motherboard for the dryer (which was a possible problem mentioned by visit #2) could be handled, but he had to have it approved. He would check with the company and get back to me. I received a call the next day and a message was left telling me there is nothing he can do with the washer. He was told by Maytag/Whirlpool that I should only fill the tub lightly and not pack it down (I told everyone how I load and I never pack my clothing down). The washer should, when loaded with wet clothing, be only 1/3 to full otherwise it decreases the wash ability dramatically.The problem of the siphoning action for the softener section of the washer should be handled by running boiling water through the tube to loosen up the wax portion of the softener. The possible correction for the dryer exchanging the motherboard (it could be set incorrectly) was turned down by saying that the dryer is running to Maytag/Whirlpool’s satisfaction and nothing else would be done, since there are no error codes for both washer and dryer.My towels have a mildew odor to them when they are used. They have to be washed twice and run through the dryer a long time before I can put them away. I purchased a high capacity washer and dryer and I am told now not to fill it more then 1/2 full. That is not what I was told by the person selling it. Otherwise, I would not have purchased this set at all.

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

I am writing for your assistance with an ongoing problem that I am having with my Maytag Series 2000 front-loading clothes washing machine. I am, frankly, astonished and frustrated beyond any means of coping with the response I have gotten from Maytag about the lemon washing machine that was sold to me. As I have never before had any sort of reason to complain about any major appliance purchase (nor about any car or house purchase), I’m not yet sure of what avenues are available to me. It seems prudent to inquire of your office before getting a private attorney to help me with this. The following is my situation:First of all, I am asking for a replacement washing machine. I am clearly saddled with a lemon.On or around December 2010, we purchased the Maytag Series 2000 washing machine from Cedar Appliance of Medford, MA. Within the first several months, the washer started ripping, shredding, and putting holes in our clothes. This did not happen during every wash cycle, just sometimes. At the time, we didn’t know if it was the washer or the (also new) Maytag dryer that was causing it. After living with this for some time, we decided to call Cedar Appliance for service. Cedar came out several times to look at the machines and they couldn’t tell what machine was causing the holes. Eventually, I started examining every article coming out of the washer to determine which machine was causing the problem. Over time and many visits later, Cedar Appliance referred us to L.A.R. Service of Wakefield MA, which they called Maytag service.L.A.R. Service came out and looked at it. They said that we were missing a part. They ordered the part and installed it and said everything should be fine. They also sold us an extended service contract. I am still having the exact same problem with the machine. Today I called L.A.R. and they told me that I had to call Cedar to get an authorization for service. I called Cedar and they told me to call Maytag. I called Maytag and after spending an inordinate amount of time recalling the details, the service representative told me that I could pay up front for an extended warranty and they would send someone out. I asked for a supervisor. I got Kitty. Kitty told me that Maytag would not replace my machine, which is clearly a lemon because I hadn’t yet had enough service done on it. I explained that I have spent hours calling for service, scheduling service, waiting for service, supervising service, and paying for service. She explained that on only one service call did they install new parts, so I needed more service. So, I should have demanded new parts on each of these service calls so that I would have earned some credibility for my lemon machine?The fact is that my family and I have lost hundreds of dollars on torn and ruined clothing caused by a new washing machine! After the boot was installed, or replaced (I’m not sure exactly what was done), we are experiencing the exact same problem. When the L.A.R. Service people left last time, they told me the problem was solved. It wasn’t. This is not normal. This is a lemon machine.Its one thing to have clothes destroyed, but what is extra frustrating is that I never know when the machine is going to destroy an article of clothing. This past Friday, we were preparing to go out of town for our daughter’s basketball tournament. I took the clothes out of the washer on Friday evening to discover that one of the blue uniforms was destroyed. There was no time to replace the uniform and my daughter was out of luck. This means that I cannot put an article of clothing into the washer that I absolutely have to have. I can’t live this way. This is a relatively new washer that should last 20 years. Right now, I can’t wash any important article of clothing. I’ve been told before that it was all set. Kitty has L.A.R. coming again this Wednesday to repair the machine. What am I supposed to do when it’s repaired? Put a uniform jersey in it? This is a very brief description of the experience I have had over the past 1.5 years with this new machine. The hours, money, disappointment, and utter frustration is more than I can describe in an email. I have attached three photos of recently destroyed items. Unfortunately, I threw away tens of items several months ago when L.A.R. fixed it.Is this unbelievable? Or are my expectations too high? Is this really what Maytag/Whirlpool has in mind for customer service? Is this really what they mean by standing behind their products? Why wouldn’t or why shouldn’t Maytag replace this machine? How much more time, money, and tears is a customer expected to spend and endure? How do I regain peace of mind and quality of running a household? Am I supposed to toss this machine and buy a new one? Believe me, that’s what I will have to do if I can’t get relief on this problem. There is no way that I can go many more months with this headache. In many ways, buying a brand new machine would be worth the peace of mind, but I am trying to make sure that my family, as consumers, are treated properly. It is also the principle of the thing. Please advise on any remedies available to me here in Massachusetts and please let me know what additional details should be provided and to whom.As an aside, Maytag/Whirlpool does not seem to be doing well with their reputation on the internet regarding customer service.

Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

Its a water saver model, so to really rinse the clothes of soap from the wash cycle you have to give it an extra rinse, which the machine has made available. So I do not know how much water it really saves.

Within the first 2 years, the dryer stopped heating. After a $300, a few parts and a few attempts to repair the dryer worked again. The sensor still kept saying check the vent and we gave up and removed the outside vent cover. Works great now. The washer worked great until year 4 when it began to sound like a helicopter. It got so bad that it literally hurt my ears and could be heard outside. It also leaked. Called repairman and they couldnt even remove the drum because it had rusted solid. After a total of 4 years we are replacing the set. Do not WASTE your money!

I have a basic Maytag dishwasher circa 2012. Not sure of the model number. It works well, no fancy features but everything you really need is there. My only real complaint is that the heat dry cycle always seems to leave the dishes a little wet, but thats common enough for dishwashers. It cleans nicely and hasnt had any issues or breaks in 3+ years. Basic. Three wash cycles (light, normal, heavy); Extra rinse option, extra hot option, and heat dry or eco-dry (i.e. no dry). Nice big rinse aid dispenser. Its not that roomy inside. Id say the size is average. It looks nice - its white and unobtrusive. It works really well with Cascade dish pods. The bottom rack is kind of a pain if your plates are curved more than usual.

Spent $2,000 on Maytag washer and dryer in September of 2020 thinking we were buying quality and a company that backs their products. Forward to January 2021 and were not able to schedule service through their website. Not able to get anyone to answer their phones. Called what used to be our local Maytag service and they told me Whirlpool took over Maytag warranty service and cancelled all the contracts for local repair shops. So, not only do we have a 4 month old washer I wish we had never bought, we cant even the Maytag to service it under their warranty! Never again...

Called Maytag to set up service call at around 9am for my washer, was given a rate of $129.00. Thought it was High but it was my only off day and felt confident that it would be a reputable company. If Maytag Priority Service would refer A&E Factory Service to me for service they must be a reputable company. I was sadly disappointed after numerous calls to A&E Factory service, a 5 hour window was not met and they were not concerned other than they would document it. Then I find out that A&E Factory Service has a Rating of 1 1/2 Star rating out of 5 and thousands of complaints to BBB and Consumer Affairs, dropped by Lowes for horrible customer service but Maytag Priority Service recommends them to service their product, says Volume on how Maytag takes care of their Valued customer after the sale. Maytag has lost a customer for life. A product without customer service and trust is nothing but a piece of metal!!!! I will be picking another Brand that doesnt use A&E. Maytag you have lost my trust and you cant buy that back.

Never dies, never have had to have it serviced. House burned down is reason why it died. So I rebuilt, bought another one, then moved took it with me, then left it with my daughter and moved to Mexico. The dryer is still working to date and this all happened over 10 years ago. I sooo want another one. Best brand period. I only buy Maytag as they last. Unfortunately I do not have one now as they were unavailable in this country so bought something different. I was told the machine I have currently was as good as a maytag - they lied. I recently found out they have them now, so when I can afford one again, I will purchase one.

I purchased this Range about a month ago and would return it to the store if it wasnt such a hassle. The set of grates that came with had 1/4 drop from the center to front of stove. Whirlpool sent a new set; they were no better. Then customer service wanted to send a Tech out to see if the grates were out of spec. If they are out of spec they will replace. If not I will be charged $89 for a service call. Whirlpool customer service assured me their service rep would have new grates on his truck. So I drove to their service provider, he laughed and said imagine they want me to send a service Tech out to look at cooking grates and NO they don’t stock them. If you want a cooking surface that is level and does not SCRATCH BOTTOMS all your cookware. The convection oven is also a joke. In order to bake something in the specified recipe time, I have to set bake temp 25 degrees higher to compensate for convection ovens automatic temp set back feature. When I turn on LF burner flames engulf 10” pan, a truly fire hazard. I have a Maytag dishwasher and dryer, love them both. Maytag should stick with dishwashers and laundry. I never have been more dissatisfied with a major appliance. I would NOT PURCHASE THIS PRODUCT.

Maytag Bravos Top Loader Model #MVWB400V90 washing machine went out and was showing code F1 code. I looked in the book and it said call service. So, I called Maytag who provided a repair number for the local authorized dealer appliance doctor. I called them 2 weeks later and the tech said, Before I do anything, you have a common problem I’ve been seeing with the motherboard in these machines. You should contact Maytag, and charged me a $100.00 service call fee. Then when I called the Maytag line, 1-800 253-1301, the first lady says I have 2 options: purchasing a $315.00 program plus which would send a tech, cover the part and 1 year warranty or get the number for an authorized repair place. But after hearing the first option, I didnt like either. She proceeded to tell me I could no longer have option 1 because I called a tech out. What?! Where do you think I got the number from, hello?! Then after I asked for a supervisor or manager, they put someone on the line who claimed to be the last and final authority (Robin) that I could speak to. When I asked does she have a boss, she said doesnt everybody? I said after several condescending comments by her. I am being treated like I am not the person who just spent 700 plus dollars and after only 3 years, my washing machine is out and you are treating me like I am the bad guy. I asked for a complaint line or email address to voice my concern but again Robin stated the buck stopped with her; what?! Is this the Maytag my family would own 20 plus years later going strong or a new version who doesnt care after you purchase their washer if it lasts or not? To ask me to spend 600 plus in repairs after you tried to offer me 300 plus in a program is ridiculous and I will never ever buy a Maytag because of this response plus treatment. I will have to buy a whole new washer after only 3 years but I am going to tell the entire world to avoid Maytag if they want a washer to last without any type of resolution beyond doing it yourself.

First, the machine is a wrinkle monster no matter what I try. I wash my clothes on delicate cycle to keep the colors longer and so my clothes last longer. This has never been a problem with previous washers. I take them out IMMEDIATELY as soon as the door unlocks and shake them out and hang everything to dry. This worked great previously and I never had to iron anything or put anything in the dryer to get wrinkles out. Now, this washer wrinkles my clothing to an unbelievable extent so that they need to be ironed or a round in the dryer to relax them. This is true on Wrinkle Guard and using the delicate setting, set between medium and none on the spin cycle. Wrinkle Guard? I don’t think so. This thing wrinkles my No Iron shirts so they will have to be ironed or steamed.The washer leaves lint like residue most all of the time on dark clothing from day one. I most recently did a load of black only clothes that I did on delicate, soil level between med to extra heavy, spin speed between med and none, and, because of the dirty clothes issue, I had the extra rinse on. The clothes came out dirtier looking than they went in and looked like I washed them with a box of tissues and too much soap. They looked dirtier than before I washed them and had a whitish and lint like residue on everything. So I ran them through the same cycle/extra rinse again but WITHOUT any soap. Unfortunately I didn’t watch to see how much water the machine sensed that these loads needed and I didn’t see how much water was there - but I did for other loads after - see the next problem below. After the second identical cycle, the clothes had the same residue which I photographed and have enclosed below. (And still a wrinkled mess.)We have found that the water sensor can’t sense the proper water level needed and is likely not functional. Sometimes it seems like it might almost be be appropriate and sometimes not at all. Specifically, after I ran the black load through, I decided to try a small red load before my usual large blue load just to see how much water there was. Same settings as above, 6 small items that barely covered the bottom of the drum and the washer sensed a medium load. Certainly by volume of clothing this was not a medium sized load and if it goes by weight, it was the smallest load possible! Medium water level… These clothes seemed to agitate ok because they were completely submerged in water and came out clean. Then I did the much larger blue load that filled the drummer then halfway. This had so many more items than the red load and weighed way more. I tried the same settings as above and this time the machine sensed a SMALL load and the water level was barely halfway up the clothes, if even that much. So half of the clothes were out of the water and we watched and witnessed that the clothes did not agitate properly. This load came out like the black load so I ran the whole cycle again including the double rinse. This time, the same load was sensed to be a MEDIUM load although NOTHING changed except that the clothes were damp and lower in the tub as they were compressed from having gone through the entire wash cycle. They came out mostly clean, after the second wash, again, likely because this time they were almost covered by the water (2/3rds or so) and could move around a little better but still not great agitation.There almost never seems to be quite enough water so that the clothes are not able to move by the agitator and sometimes we watch and can see that the clothes above the waters never get pulled into the water. I understand that this machine may not completely cover the clothes but this seems way short on water and the fact that things usually come out dirty means something is wrong. There is often so little water that the agitator can’t possibly work the clothes into the water. So, next I ran an Oxi cycle and witnessed that about half of the items were not in any water and were only wet because of the filling cycle not because they were moved around by the agitator. How can the oxi do its job if the clothes aren’t in the solution of at least wet from the solution which I didn’t see as likely as the clothes didn’t seem to move through much if at all?Along with the same water sensing problem, why on earth isn’t there a manual water adjustment? If the water sensor doesn’t work, the other option is only the high fill setting. After finding my clothes still dirty when we first got it, I tried the high fill setting to see if this would help but the clothes still came out with that residue. This was the very first few loads I ran and was assuming it was just user error so I studied the manual and tried everything as recommended. Since reading that residue can result from too much water, I use the recommended sensing feature now. So, we can either have too much water or barely any at all…

Purchase date of Maytag dishwasher 12/9/11 for $651.37. Controls broke 6/2013. Used Maytag specified repair service at cost of $450. New control panel installed 7/9/13. Control panel broke again 8/13/14. WILL BUY NEW DISHWASHER. NOT MAYTAG.

2 weeks after my warranty is up, the control panel is shot. They used to make quality products and that is why I purchased a Maytag. I had before this a very cheap dishwasher from G.E. and it lasted 9 yrs. I cant believe it is already broken. Do not buy Maytag!!

Such a horrible and expensive kitchen purchase. The stainless looking pieces are either fake or very poor quality - they scratch so easily. After the first year of use the top of the stove looked like it was 30 years old. The oven glass is extremely hard to get at to clean - you have to remove very finicky screws that dont go back into place easily. Oven temp is questionable and it takes a very long time to heat up. I would never recommend the Maytag Gemini oven to anyone.

Well bought this washer a little over 1.5 years ago in 2017. The display started going haywire, flashing, going on and off and would only go to the normal setting, most of the time. Called Maytag and had service come out and Maytag would cover parts and labor. Turned out the control panel went bad. About a week later found out today part was still back ordered and not available with no ETA. So was told Maytag would replace the unit. So until I find out whether or not they will actually replace it, Im giving one star. Been holding for customer service for over 35 minutes now to verify what I was told. Its a shame because this washer was given a good review. It is a front loader.

I purchased a Maytag dishwasher 15 months ago and was told the control panel is bad. It would cost me $120 to have someone look at it. I might as well buy a new one by the time the parts are added. I called Maytag and they said that there was nothing they could do for me since I was three months past my warranty. Meanwhile, I see all of these complaints about the same problem and Im wondering why there has not been a recall on this. What does it take for that to happen? I will never purchase a Maytag again! Their customer service leaves a lot to be desired. All they do is apologize like its programmed in their heads. This feels like a fraud!

We purchased a refrigerator in December 2013. It quit working less than 8 months later. The company contracted to repair it made us wait 4 days for service; they did not repair the unit. We are now expected to wait another 4 days for them to return. STAY AWAY from Maytag!!!

I would have given this washer/dryer a 0 star, but wasnt able to. Bought the pair and first thing, couldnt get enough water in the tub, clothes wallowing around for an hour in the few cups of dirty water that it allows. Cant even believe how terrible this combo washer and dryer is! Now I get to wash everything in this piece of ____ twice, thank you Maytag! Just took out a load and it is dingy and stinks, so now its wet, on the floor waiting its turn to go back for another wash (possibly even a third).If you want clean clothes, do NOT get this washer. Dryer has issues also. For whatever reason, the AF signal has been on for a couple of months. Turn it off and back on and its okay for a bit, then back on. Its the Air Filter. Its not plugged, so I dont know, I just keep using it with intervals of resetting it altogether. What a total waste of money. Am going to give it away for free as soon as I find a replacement! Save yourself a huge headache and look elsewhere than Maytag. Oh, and if Maytag happens to read my review, you can contact me for a refund any time, just respond to this post, you can even come pick it up and get it out of my home. Thanks a bunch!

I bought the Maytag because of its reputation and as a washer it hasnt disappointed me.. It gets my clothes clean with a minimum amount of effort on my part and it doesnt use a lot of water... I love my washer.

Maytag Centennial commercial technology washer - Bought what I thought would be a great washer given the Maytag brand about 3 years ago. Started out ok But has gotten progressively louder and noisier. We cant even hear the television on the next floor of the house when the washer is running ridiculous. Now it wont work at all. Outside of warranty and a real pain. Not sure what to do but if I have to buy a new one its not going to be Ay

Maytag French door Bottom Mount Model # MFT2976AEW02 - Purchased this model refrigerator in late 2013. Had minor problems with ice maker for last 6 months, not have freezer problems, as the bottom freezer is not keeping food frozen. Called repairman today. He ran 64 checks on refrigerator, said to keep eye on problem and he will re check in 24 hours. Called private company, Maytag in Latrobe. They referred us to the Maytag repairman. We will keep you posted. We moved all of our frozen food to a downstairs older freezer for safekeeping. Keep checking, we will update.

We loved the YMMV4206 microwave - at first. After the warranty was over, we started having issues where we would put the food in the microwave and try to enter the time, wed get the message to open door and close door. Wed try that and for the next few months it would work. At the 18 month mark, thats all it would do, was tell us to open/close door. We ended up unplugging it and it has been unusable since before Christmas. When I call Maytag and related to the support staff our problem, they were of the attitude that it is out of warranty and we can send someone out to take a look at it - for $130 + HST without even repairing it, that would be to diagnose the problem that we already know, then we would have to wait for them to order the part and come back. Do Not Buy this product.

Bought this because of the load capacity and it seemed like it would be a good purchase to help save on water. But worst mistake ever. The water level barely touches the clothes on top. It barely has any water whatsoever. All my dark colored clothes come out with residue. It’s disgusting and cleaning with Affresh does no good either. Very disappointed with the company.

My husband bought me a Maytag washer as a surprise gift. I was so excited to get a Maytag. I will never purchase a Maytag again. I am so tired of washing, rewashing and rerinsing my clothes and still not getting the soap out. I have used every different kind of detergent and used with and without fabric softener. I have also tried cold, warm and hot water. I would rather use more water and get the soap out instead of using more electricity to keep rewashing my clothes and then in the end having to take a wet cloth to get the soap out. Never had to do this with any other washer I owned. Very disappointed as I always thought Maytag was the best.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

I am a WWII vet. I bought a Maytag dishwasher 4 years ago from Home Depot... Cost me $600 in total repairs. Maytag would not help. My son just brought it to the dump! At that same time I bought a Maytag bottom freezer from Home Depot... It has never worked right. Ice dispenser broken after 1 year, food freezing in fridge at any temperature... It just died! Maytag refuses to take any responsibility for THIS POS!They should be ashamed at the way they treated me. I am 94 years old, and have fought for our freedom, and was looking for one simple thing from this American company. Its called fairness! Maytag sucks! You have lost a lifetime customer. You have lost my son as a customer, and will lose anyone I talk to, as well as my son posting on ALL social media! SHAME ON YOU MAYTAG! SHAME ON YOU MAYTAG!

Our Maytag Bravos Quiet Series 300 is anything but quiet. Within two years of purchasing it, we now hear an F18 jet fighter taking off from our laundry room. Neighbors near and far come running to avoid getting injured when the spin cycle kicks into after burner. Seriously though, this looked to be a nice machine and operated flawlessly until a month ago when the spin cycle started sounding like a jet fighter taking off. I am handy and often fix appliances and things around the house. From reading reviews here on Consumer Affairs and other places, I am finding that the noise problems are more common than not. Investing $400+ into a replacement tub/bearing set would further support Whirlpool/Maytag and the sucking sound they make to get at my wallet. From what I have read, I am likely to have more problems after fixing this one (it will likely break again). I am going to quit while I am ahead and purchase a new washer. Whirlpool/Maytag will never see my business again. Its ludicrous to have an expensive appliance like a washer only last two years. BTW, I just spent $200 to replace the control panel on my 4-year old Maytag dishwasher. A cheap and horrible design. The part probably cost $10 to make. BOHICA. (bend over, here it comes again). FYI: Whirlpool owns and sells its products under several other appliance names. Names that include, Kenmore (yes, Sears), Maytag, KitchenAid, Jenn-Air, Amana, Gladiator GarageWorks, Inglis, Estate, Brastemp, Bauknecht and Consul (Wikipedia source). Like a Lotto Scratcher, peel the Whirlpool or Maytag name sticker off and underneath you will find the real name... CRAP! Its sad to think that you have to purchase products made in Korea to get quality. Very sad.

Purchased dishwasher from Highway Appliance in Dunlevy, PA on August 21, 2013. In August, 2015 control panel apparently went bad. When pushing normal, other buttons light up, but not the one you select. Tried throwing the breaker to reset, to no avail. Based on reviews, seems like many others have the same problem. Step up and do the right thing Maytag - recall & replace these machines!!!

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

We went to Home Depot and bought a Maytag front load dishwasher and dryer and microwave 3-1/2 years ago. The washer and dryer were put in right away. The dishwasher and microwave stayed in their box for another year due to us remodelling the house room by room and the kitchen wasn’t done for a year. We put the appliances in and the dishwasher panel went out in October 2011. The washer in April 2012 started having a failure 8 when it gets to the last spin and rinse in which takes a lot of shuffling clothes to get it to finish its cycle. Then last night, May 14th, 2012, the microwave caught fire and all I was doing was brew tea in a glass Pyrex measuring cup not to mention the fan didnt work from day one. The whole house was full of smoke and it melted the plastic. So the most I got out of 3 of these products is 3 years at the most. This is very sad that we spent this much money and it lasted less than 5 years. I am writing this to warn consumers not to buy Maytag appliances. They should last longer than 3 years and are not cheap to buy. This makes me very angry and I hope someone takes this seriously and work on the problems before someone burns up due to these appliances catching fire. Our dishwasher had a recall shortly after we installed it due to the element catching fire and we had your repair man replace it.

My experience over the past 2 years with my top loading Maytag washer is echoed in almost every review here. 1. Not enough water to clean the clothes 2. Clothes come out still dirty and covered with detergent 3. Barely agitates 4. Repeated repairs for leaking and computer board breakdown 5. Complete lack of interest by either Lowe’s and Maytag when contacted. I could write a long, detailed complaint but it has all been said quite well. We need to band together and file a class action lawsuit against Maytag. Any lawyers out there willing to take this on?

We bought the Maytag Aqualift cooktop about a year ago & are continuously dissatisfied with it, for several reasons: 1) the cooktop is a huge nuisance to cook on. The burners are either raging hot (causing boil-overs), or too cool to simmer. The boil-overs then require much cleaning with an expensive cleaning agent. 2) the oven, whether you use regular or convection, underheats - so you can’t tell how long the cooking or baking process will take, & you have to monitor the cooking process. 3) the so-called self-clean is a joke; the oven will not be clean unless you crawl inside & clean it manually. Overall, I’d prefer to toss this range in the trash. I’m a good cook, but I get angry every time I use this expensive, poorly- designed product.

I bought this Maytag French door model MFF2258VEW2 in 2010. Within the first year, it was freezing my vegetables. They sent someone out to fix it. Thank goodness it was under warranty. The man laid the bill down and it was over $800 to fix it. Six months later, it froze up. I called and they said they would send someone out, but I would have to pay for it. Im on disability and cant pay that kind of money. I got someone to come out and fix it. Well, guess what? It has started freezing my vegetables again. This is the third time this thing has gone bad. What do these people think they are doing putting things out like this? I had a Maytag for 30 years and never had any problem with it. So I saved and saved to get me a new one but I will never buy another Maytag. The company should have to replace all the refrigerators that are like this one.

I have had my refrigerator freezer for 2 1/2 years. It worked fine until about 6 months ago. The vent started freezing and then water ran to bottom of freezer and freeze. If I get this fixed, I hope that will be the end of the problem. I am going to defrost it the old fashion way to see if that works. I will never buy this product again.

Updated on 02/13/2021: Maytag stove purchased 15 years ago for about $500. Replaced mother board about 5 years ago which wasnt cheap, but otherwise, stove has performed with no problems and still looks and behaves like a new stove.Original review: Our 6-7 year old well cared for Maytag range oven recently stopped working. After a service call for diagnostics, it was determined the electronic module controlling the clock and all oven functions was dead. We were told by the Maytag service tech the module cost was 300$. That cost plus labor for less than an hour, plus the 60$ diagnostic visit came to almost 500$ which is close to cost of a new stove. The technician answered yes to my question, Do you replace a lot of these? He also said the cause may be power fluctuations making me think that surely there is a way to prevent this kind of failure. So, since the price seemed exorbitant, I wrote Maytag to inquire about causation/prevention, etc. I received a fairly prompt and polite reply with totally no explanation. I wrote another email with relatively the same results. I dont recommend buying an electronically controlled Maytag stove.

Never buy from Maytag. I and my daughter bought from them two refrigerators of them. After one month my daughter started to fix. I am started after one year or it is leaking. Our freezer destroyed and realize this after one day all my food I throw away. The same was with my daughter refrigerator. My daughter have old refrigerator it is working without problem for 50 year never fixed. Never ever buy from them anything. It is good I was at home. Sometimes I am traveling if it happens this time. I do not want to think about this. For fixing you have to pay lot of money. I hate that I purchased something with them.

We bought new appliances when we moved to our new house last June (2016). Sears recommended the Maytag 600S pair (HE washer and dryer). We have contacted Sears numerous time to have service people out because many times (75%) the washer does not fill with enough water to wet all the clothes and there is a layer of dry clothes at the top when the wash cycle ends.I do not believe that dry clothes get clean because they are near wet clothes in the washer. But Sears insists this is by design. Some service people tell us that the top loading HE washer will be gone soon because of the complaints but we have to struggle on. Sears seems to hope we just get tired and stop calling as their Customer Service policy. I have to dump 1-2 buckets of water into almost every wash that we do. As a side note, the 600S series has a slanted top rather than the traditional flat top. It looks cute but things fall/roll off of it. It would be nice to put things on top of the washer or dryer while doing the laundry but they roll/slide/fall off. The design is not so cute anymore. Actually, really a stupid idea.

I purchased a Maytag gas range after remodeling my kitchen. I thought I was getting a good product, boy was I wrong. The ceramic gas grates are so slippery that pots tend to slide off but the real problem is that the racks inside the oven fall when you place pots on them. I tried cooking a Thanksgiving turkey in it and the racks fell to the bottom of the oven. It appears that the top rack and the bottom rack are the only two that stay in place. And it also appears that when the oven is on, the sides of the oven expand so that the racks fall. I have tried to contact Sears as thats where it was purchased to no avail. I will now attempt to contact Maytag directly but it appears that I will also not get anywhere there. I have read at least one other complaint of this exact same type happening to someone else. This is very dangerous. Do they really want a lawsuit?

Washer needs new transmission at only 3 years old! Maytags 10 year part replacement doesnt cover it. The company actually asked why I didnt purchase extended warranty, I thought I didnt need one. Bad bearings, it doesnt wash the clothes clean, $400 to fix it. Needless to say Im buying a new washer and it will not be a Maytag, worthless piece of scrap!

I purchased Maytag French door stainless fridge 5 years ago for $2200. The doors were out of alignment and I put in new control board; both items almost right away. Then in May 2011, we had to replace another control board for about $400. Then in July 2011, the compressor went out at a cost of $300 for the compressor, $350 for labor. I called to Maytag, Gwen agreed to pay for the compressor but not the labor to put it in. So we now have about $1400 invested in our $2200 refrigerator. Letters to Maytag CEO Mr. Fettig remain unanswered. Do not buy a Maytag appliance!

After purchasing this washer in 2007, the washer started to smell like sewage. At first we werent sure it was the washer and had a company come out to check the pipes. After this and calling Maytag complaining without any luck. We were told to buy affresh tablets and run it through the washer once a month. This last only so long and the smell comes back. Now when the washer goes into the spin cycle it sounds horrible. Again called Maytag without getting any resolve. I will never buy a Maytag again!

We have had this refrigerator (Maytag Side By Side Refrigerator with Ice Dispenser 27 CU) for 5 years this month and have already had to have it serviced once and now the ice dispenser just went out. I wish there was a brand out there that did not have problems and when problems occur, you do not get the runaround to get them fixed!

Maytag Maxima 9000 washer not working since day 1: I have placed a call on Friday, June 14, about my Maytag washer not working. The service man came in on Friday, June 15, 2012, and stated that a UI board needs to be replaced. I have called Whirlpool to ask for the part to be ordered so it is faster, could not do anything. Then, I have not heard from Whirlpool since. I called them again on Wednesday, June 20th, and I was told that the part was ordered and it will take up to 10 days for it to arrive. Once it arrives, the technician will call to set up an appointment. So, according to Maytag (Whirlpool), I can be without a washer for at least 2 weeks (as 10 days are 10 business days) and it is all good.

This dishwashers start button stopped working after 1 1/2 years. We did not buy the Extended service warranty. So we are responsible for the service call and the replacement of the control panel. Ridiculous. I called Maytag to file a complaint and they never returned my call. I will NEVER buy Maytag again. There are enough problems posted to know better. This company should be ashamed!!!

Just a year after purchase, this Maytag Bravos Washer stopped spinning the clothes. It never washed worth a damn anyway. I paid extra money for a quality product from a known brand name and I was taken to the cleaners. Never buy a Maytag product unless you want to replace it in a year.

This Maytag (1979 model) is about as good as other dishwashers (I always rinse before placing in machine). It does have a lot more buttons that are not used than the last one I used (installed in the 1950s). Delayed start, choice of preheating water or not, choice of drying. Not big enough to do everything when have company and too big to use when no visitors present. When I am alone it takes 3 months to get enough to fill the machine and by that time they are getting moldy so most of the time I wash by hand. Black glass front with imposing row of controls across the top. I normally do not generate enough dirty dishes to warrant having a dishwasher. Since my wife died I have used the dishwasher two to three times a year.

We have a Maytag Neptune washer and dryer. The seal is full of mold. We replaced the seal a few years ago and I wipe it and try to clean it every load, but it is useless. I saw there was a class action suit and I was never notified of this. I would have participated. I want it fixed, replacing the seal does not work.

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

At first the Maytag Bravos XL top load washing machine met all me expectations. After 3 yrs. the top where you load bleach and fabric softener began to rust. This is not covered under warranty. My last washer was a Whirlpool and had it 15 year and never had that issue. So it cant be from the water, just poor workmanship. Very disappointed. Now my lid came loose and is ready to fall off. Would not recommend.

I purchased a Bravo 300 MVWB400VQ in 2009. I knew in 6 months that I had made a huge mistake. The clothes began coming out soaking wet - the dark clothes have lint, pet hair, and rings on them. The large capacity drum is just that... a big drum. If I wash bedding in it, it becomes off balance and sounds like its fallen over. I have used only HE detergents, and I wash the washer (yes, wash the washer, does that tell you anything?) before the light comes on. Now the machine sounds like its full of loose parts or rocks in it when it begins to fill up. Its even worse when the water starts to pump out. Now that Ive read all the other complaints, I realize that Im doomed. All of these trusting people have been cheated out of nearly a thousand dollars for a piece of junk. What good is Consumer Affairs if there is nothing done when there are so many complaints? I will join any lawsuit against Maytag if ever there is one. This is another lemon that promised everything and delivered nothing.

I just purchased this washer in Feb. 2012. The motor had gone out in Oct. I called Maytag Service, they came out to repair it. In Nov., it was doing the same thing again. I called Maytag Service, and they sent someone out to fix it. They expected me to take off from work where they inconvenience me with this washer. It is a reject washer. They would give me another washer and not consider people having to work and cant take off for their reject washer. They said as long as it is under warranty. I feel that I should be able to get me another. This washer has given me problems since I had it.

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

I have a dishwasher that would randomly leave chunks of food on dishes, above and beyond not working and would take entirely too long to clean the dishes. This silly thing would run for hours but still produce dishes that were clumped with food. The local Maytag could have cared less. They said that it was the wrong detergent or hard water or we have not pre-cleaned enough. I am taking the old dishwasher to the range for proper disposal as a backstop, and buying something not made by imbeciles.

I purchased the Centennial Commercial Technology washer in June of 2013. In the last 2 1/2 years it has been repaired 3 times. The transmission had to be replaced twice. My household consist of two adults and definitely it is not overused or overloaded. The washer currently is not working. Consumer service cannot schedule an appointment for repair for 2 weeks. Previous repairs took approximately 2 weeks to schedule a service appointment and it took another week to two weeks to get the part in and washer repaired. I have decided to consider this an expensive learning experience and will not purchase Maytag products in the future!

My Maytag MDB7749SAW0 Dishwasher starting acting up after around the first year. The lights on the Control Panel began to flash uncontrollably and it will run all day while I am at work. I called Maytag and they were nice but did not repair it because the warranty just ran out. The person on the phone said that it is a common problem with knob-less dishwashers, the humidity causes problems with the control panel. The cost to repair was over $300 to replace the control panel.

About 9 yrs ago, we remodeled our house. And when it came to appliances, I was vehement we were going to go with Maytag because of their great name and reliability (We have 7 sons and needed reliable appliances). Boy, was I ever wrong?! We have gone through 2 Maytag dishwashers and countless repairs to the Maytag dryer. And our top of the line refrigerator has been a piece of junk!Of course, shortly after the year warranty was up, the flimsy pieces of plastic holding up the shelves started breaking off. The repairman, who came to replace the cooling coil on the refrigerator, said those shelf plugs couldnt be fixed. The whole front of all drawers have come off as well. He mentioned that Maytag was going bankrupt and started compromising on fit and finish. And he said that we just happened to purchase in that time frame. Now, we have a compressor that needs to be replaced for over $500! I have, in my garage, a Gibson freezer from my grandma that is 40 yrs old, and literally the most reliable appliance we have. Never have we made any repairs to it!I called Whirlpool (since they bought Maytag) to tell about my horrible experience with Maytag, and let them know we have to replace these appliances. I asked if there was anything they could/would do (discounts whatever) to redeem their name. I was told that they would not be able to help at all. So, I told them that I would not give Whirlpool anymore of my business and warn anyone I could, not to buy Maytag, Whirlpool or Amana. Isnt there any appliance company out there who cares about customer service, a good name and a reliable product?!

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

This dishwasher is at 10 years old, but is a real workhorse. This machine cleans like no other! Never worry about our dishes being clean. But we have replaced the seal once.

We purchased our Maytag 4000 series washer and dryer (Model: MHWE450) in December 2010 from Best Buy. For the first six months or so, we were very happy. We started to notice that the washer was getting a little louder by the month. I checked the level multiple times to be sure that wasnt the issue. Assuming it was just part of how the washer broke in, I just let it go - a bad move! Fourteen months after I purchased the set, the washer flooded all over the floor. I opened the washer and pieces of plastic were all over our clothes. After further inspection, the drain was completely full of the same plastic. I cleaned it all up only to find that the washer tub was so loose that it was banging side to side.I called Maytag to ask for help or suggestions. They basically told me that I was out of warranty and kind of out of luck. I responded that we do a total of four to five loads of clothes per week and that there was no reason that this commercial series washer should have failed after 14 months. They offered a one-time service plus extended service contract. Feeling that I had no choice, I spent almost $400 assuming that I had a fixed washer and a year extra warranty. I was told that someone would be out to look at the washer in three days. Finally, after me pressing and pressing, someone showed up a week later. He put a list together of all of the items that were needed to repair the washer.Two days later, Maytag service calls and says that the washer will be too expensive to repair and they would be giving me a reimbursement for buying a new one. They didnt have an exact amount yet. Two more days later, they finally called me with an offer of around $550 ($250 less than what I paid) based on their research of what I should be able to find one for and directed me to the website. One big catch though - it didnt include the $125 shipping charge. When I called to request for it to be paid as well, they declined with basically a “take it or leave” type of attitude. Not knowing what to do, I called every local appliance store until I found someone that had two in stock. When I went to look at them, I was told that both of the ones that they had were rebuilt because that model Maytag washer had a major issue with the bearing and basically needed to be replaced on all of them.Luckily, I was able to buy the washer and a five-year extended service contract for around $690. So in the end, I paid $799 for the new washer, $400 for a warranty, another $100 to replace the washer, and close to $100 in laundry mat costs for three weeks. I promised everyone that I spoke to with Maytag that I would write a review to share my story and thats why I wrote this. The repair plus warranty is a joke. I like this washer/dryer but will never buy another Maytag appliance again. Next time, I will buy extended service contract from the start.

Purchased the Maytag Bravos upon recommendations from Lowes and Home Depot to replace a 20-year Kenmore that finally died. Since the Maytag brand was always considered to be the top of the line washers, we purchased the pair. About a week ago during the spin cycle I thought that a 747 was taking off in our laundry room. Called a local appliance repair service who said that there had been numerous issues with the Bravos series and to call Maytag to inquire about a recall. After 45 minutes on the phone with a very sweet naive young lady, she told me that the new models did indeed have a 10-year limited warranty on parts. However my 3-1/2 year old washer was not grandfathered into the warranty. I could (a) pay the $150 service charge to have someone come to inspect it or (b) buy a new one. I will be purchasing a new one but it will not be a Maytag or Whirlpool product. Now we know why the commercial for the Maytag repairman is not running... Hes now very busy working on their broken products.

I purchase this dryer not even a year ago. It is not performing right. I call customer support and they willing to try something to see the problem. I hope I don’t have to pay anything out my pocket.

Bought machine 03/23/15 exactly 2 yrs ago & machine will not work. It looks like the electric panel and which there are a lot of complaints about the panel, and the lid. It seems as its about the extended warranty now. The quality that Maytag advertises is lies. You buy the product and you have no choice but to purchase a warranty on your machine. Simple is better when it last 20 yrs over 2 yrs on a fancy machine. First electric panel machine washer with a horrible experience. It will cost 98 just to look at, that is not including parts and labor. Its 339.15 for a year warranty which equals over 300 per year for 3 years. Overpriced in all ways. Worse choice ever.

I built a new house in 2006. As part of a builders package, we had all new stainless steel Maytag appliances installed. The side by side refrigerator compressor stopped after 26 months (of course, passed any warranty). No customer support through Maytag and as previously posted very scripted responses. Maytag microwave handle has broken off several times, the glass seal in the oven door was compromised and the inside glass is stained - most recently the on-going issue with my Maytag dishwasher model mdb5601. Ive already replaced the handle /door latch assembly twice and am confronted with the current dilemma if I should replace the control panel that now appears not to be working. It goes without saying that I will never purchase Maytag products again. However, I am not in a position to replace what are fairly new products. That being said, I am reluctant to purchase costly replacement parts given their poor performance and ratings as mentioned in this thread.

I purchased a beautiful Maytag dishwasher for $700+ and it died after a year of use. I called Maytag to complain and they dont care. Pay $350 for a tech to come fix its warranted for a year or fix it yourself. I fixed it myself for $180 and am hoping the very same key panel wont fail again. I know it will. I wrote to Maytag about the issue and have not gotten a response. Im hopeful that they will make this right or that they get sued and the consumers get their money back.