Maytag MVWC300BW clothes washer makes holes in heavy duty T shirts & sheets. It stretches clothing. We are following directions in loading without success. We are washing everything on the gentle cycle twice to get the clothes clean without destroying them. Today we were stood up for our third service call.

We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

We purchased a Maytag dishwasher in January of 2011. Two years later the entire machine stopped working. We had purchased the extended warranty and the control board and panel were replaced. Now two years later it happens again. Maytag/Whirlpool is of no help nor do they care. DO NOT purchase their product!! Multiple complaints and issues with faulty control panels and the cost to replace one is the same as buying a new dishwasher so they cant lose. I will never again own a Maytag or Whirlpool product.

Bravo Large Capacity Washer with Optimal Dispensers - 4.3 Cu. Ft. - The washers shortest cycles take at least an hour (not including having to do another spin/drain) and uses such little water that I have to use the extra rinse cycle on most loads. The washing machine is VERY hard on the clothes; towels (which I feel are pretty hardy) have been destroyed. Today the machine stopped draining/spinning completely and smelled like it was burning. I called the warranty number and was told it would be a week until someone could come out. When I tried to escalate a sooner repair date the manager Jessie refused to assist in any way insisting there was nothing he could do. I spent the morning calling my local repair shops and was able to find a Maytag warranty repair person to come out the same day, but had to call the warranty number again and have Maytag place the request. Sorry for the long post, but this washer is the WORST purchase I have made. The warranty experience was very unimpressive. I will not be purchasing anything from Maytag/Whirlpool/Jennair ever again.

This Maytag dishwasher has been really dependable, looks really nice, is really quiet, we have absolutely no complaints. I hope it lasts as long as I suspect it will. Would highly recommend this dishwasher.

The washer I bought brand new has never worked well. The clothes end up all bunched and twisted up together. The bleach is not distributed properly, I have big blotches of white spots. It is leveled, still shakes and everything is on one side

Purchase a top loader washer machine in Nov 2014, it is now Jan 2015. It is not completing drain cycle, leaving wet cloth. I am Not happy with the service. I had the tech people come out 3 time and saying to call customer service, and they keep sending out people. They do not want to give me back my money. Unhappy, waste of money, will not get another Maytag appliance again.

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

Bought a Maytag MVWX655DW top loader clothes washer from Best Buy on 7-7-2020 it was delivered as promised on Friday 7-10-2020. The people who delivered it were very professional and nice. They did a great job installing it. My wife went to use it for the first time Saturday morning 7-11-2020. Luckily this washer had a see through door. We could not believe our eyes, it never put enough water in the tub to cover the clothes. So as we watched the clothes on top never participated in the wash, they just moved around. When it went to spin cycle it was making a loud clicking sound as it was shaking. So we tried different settings, after 3 loads I called BB and said I want to return it. This machine has been mislabeled, its not a clothes washer, its a noise maker at best. DO NOT BUY THIS MACHINE. IT DOESNT WASH CLOTHES.

We purchased an entire suite of Maytag kitchen appliances in September 2014 at a cost of $4300. Have had problems with every single item. The MMV5219DH microwave was the first issue. After a year it began to give us erroneous display messages when we tried to use it. We would input the number of minutes we wanted the food to cook, and wed get a message saying CHK TIME/OPEN DOOR. Repeated door closings, resets of the time, etc. did nothing. Sometimes if we hit cancel it would work - other times not. Wed push every button on the keyboard and eventually wed get it to work - perhaps 10 minutes later. When I called the appliance store (Vics Appliances in Saco Maine) I was told to unplug it for an hour. Okay, that corrected the issue - for a few days. When the problem continued, sometimes unplugging it had no effect - other times it did. Eventually we figured out if we didnt reset the clock time it would work most of the time (not 100%). The Maytag refrigerator began to malfunction at the same time (not keeping temp, and the ice in the icemaker melting and refreezing in a big lump that blocked the door water/ice dispenser) so we called Vics again and set up a service call. Serviceman reset the microwave to factory specs and we will see what happens. He also reset the fridge to different temps, and 2 days after his visit it has again melted the ice in the icemaker and formed a blob at the bottom. DO NOT BUY MAYTAG!!!

I purchased Model #MHW563HW Frond loading automatic washer a little over 1 year. The options are not for me. The quick wash is way too short 20 minutes, all the rest of the options are 51 minutes to 2 hours & 57 minutes! If you wanted to add some extra minutes to the Quick wash you are out of luck. Normal wash is 55 minutes but can last much longer, it takes forever for this machine to balance which adds time to the process.I had an LG front washer before this one and when the clothes came out they were almost dry, not this washer, they are very wet. Then there is the horrible odor that comes after you use it, Ive tried drying every area making sure there isnt a drop in it. Still the stench is unbearable. Yes it has a Clean Washer with Affresh option which takes an additional 128 minutes and you have to do it at least once a week! Thats a LOT of wasted energy. That just doesnt sound efficient to me, washing the washer. Why??? This washer had great reviews which I read, not one mentioning these issues.

I bought a Maytag MDB8959SBS2 December 2013 with several major appliances for our new home while they were all deeply discounted and bundled with cabinets etc from Lowes. Moved in June 2014. Said dishwasher crapped out last month (May 2015). Buttons all fouled up, push normal and 6 other lights come on. Tried different resets, reboots, power down all no good. I ordered parts to repair, control board, control box, no luck. No warranty because purchase date was December 2013. This thing didnt last 11 months of use, and its just my wife and I running maybe 2 loads per week. I will certainly do more research and buy a foreign make/model or at least one not made by Maytag or affiliated brand. Unfortunately this supposed Made in the USA sticker sure doesnt stand for quality with this company.

Updated on 08/13/2021: Today a repairman who is authorized by Maytag came out. He found the problem, some arm that popped out that is located underneath the washer. He put it back together and said he needs to order the part and it will take 30 more days. Set the washer so that it SHOULD work for a couple of loads. I spent $700 on a washing machine and I have to go to a laundry mat to get my clothes washed. Here is the clincher. The guy left no paperwork, nothing, not even a business card. So I am at the mercy of this repairman (I think he said his name was Jessie). The guy was friendly, quick and knowledgeable, however he told my husband he knew what the problem was going to be, if you knew why didnt you bring the part with you and he said the part is out of stock. Why, is this part unique to Maytag washers? So I am still waiting for my washer to be fixed.Original Review: In December 2020 I purchased a Maytag washer it was delivered in January 2021 and it worked great for the first several months. Then the machine started making noises, clicking noises like it couldnt move through the gears. Then I started noticing that my clothes were not getting cleaned. It was taking an hour to wash the clothes. I told my husband it is not agitating just clicking. We had to stop and start back up the washer just to get the water level high enough for the so called deep water wash. I was finding residue left on my clothes and had to wash them 2 or 3 times to get the clothes clean enough to wear. Sometimes it wont spin enough to empty the water in the tub. It smells almost like wire burning. It has barely been 6 months and I have to have a repairman out. I will review the washer again after it has been fixed or replaced. But as of right now I will never buy another Maytag again.

We have a Maytag Gemini Double Oven Range Model MGR6775ADW. This is a gas range and it was purchased in 2006. This past Saturday afternoon after cleaning the dishes, the igniters on the range starting ticking on their own. I checked to make sure the knobs were not on and they werent. The ticking finally stopped after about 2 minutes. After the ticking stopped, we planned on going out for a walk. Fortunately we didnt. In about 10 minutes after the igniters quit ticking, the range burst into flames. Flames were in the top oven and shooting out the vent holes and the holes where the knobs are located. Coal black smoke was also pouring out of the vents. I quickly pulled the stove away from the wall to prevent the cabinets from starting on fire and I pulled the plug to shut off electricity from the stove. The flames subsided shortly after pulling the plug. The kitchen and house smelled of burning wire insulation and plastic. After doing some research on the internet, I found out that many other people have had the same problem. I reported this to Maytag Customer Service and they wanted to send a repair technician to fix it. I told them I didnt want it fixed but wanted it out of my house. I told them I didnt trust the range since some people reported they had it fixed and the fire occurred again. I wouldnt be able to sleep or go out anywhere knowing that the kitchen range could erupt into flames at any time. The factory authorized repair technician, from A&E, did come to inspect the damage and to report back to Maytag on his findings. He admitted that he wouldnt even trust the range in his house. After paying $1300 for this range and only getting 6 yrs. of use, I feel that we deserve some restitution from Maytag on this badly designed and dangerous piece of equipment they have been selling. Do not buy the Maytag Gemini range. This is a bad and dangerous product.

I purchased a Maytag dishwasher delivered in dec 2012. We are snowbird Canadians and the dishwasher is only used 5 months per year. Jan 2015 the control panel quit working and the repairman tells me the wires on the control panel have started to melt down. He called Maytag and was told they had extended the warranty on this machine for one more year. Missed it by 2 months. Considering this was only really used one year, I am very disappointed. How can an extended warranty on a safety issue only be for one year? This is my first Maytag product and will be my last. I only purchased it because I was told Whirlpool bought them out and I have never had a problem with Whirlpool.

We too were having a water leak from the French door freezer and a sheet of ice under the freezer drawer. The repairman came and told us that it was a common problem with the French Door fridge and an easy fix. Maytag has a new P type defrost hose that doesnt freeze up. He changed the part, $149.75 bill, and no more problem. Should Maytag have let consumers know this was a part that was failing? Yes, definitely. But at least the fix was reasonably cheap.

The Maytag Bravos XL low water washing machine is very disappointing. About 20% of the time it needs a second rinse because there isnt enough water released to rinse clothing. Forget washing anything large. It just doesnt do it. Waste of money. The matching dryer is just fine - no complaints.

July 2018 I bought a new Maytag electric washer and dryer. After one mo. the enamel inside the dryer started come off in sheets. It was replaced with 2019 model which after 3 mos. wont come on unless you unplug it and plug it back in after using it. I am now waiting for Maytag to send a repairman to come look at it. Steer clear of Maytag front load electric dryers.

All my kitchen appliances are from Maytag, however I would highly recommend buying the extended warranty for any appliance you buy. Maytag is not helpful to customers when it comes to repairs. They will recommend you their authorized companies which here in Colorado Springs are the one with the worse review and already knowing the the repair will cost more than the cost of a new one. You will have to be available 5 hours of your day and spend $110 for a guy to come to your house and tell you that the repair will cost more than a new one. Oh and if your microwave is a 2.0 CU like mine you will have to pay $300 plus in double labor because your microwave will require two people to take it down from the kitchen cabinet.

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

We recently purchased a Maytag refrigerator, love it, no problems until the mystery person in my house accidentally broke the slide out door for bottom drawer. So I called Maytag, and with no questions asked they sent me a new part by Purolator! Great customer service makes everything better! Thanks Maytag.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

All in all I have liked my electric range, but I have 2 issues that I am having trouble resolving. I bought the range in 2003 and to find the model number I have to pull the range out from the cupboards on each side which would be extremely difficult under the circumstances. The reason I want to get the model number is so that I might find replacement parts for the doors edging that has flaked and rusted and is quite unattractive.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

I wish that I had looked up reviews before purchasing my washer 6 months ago! No matter which setting I use, the washer never fills up with enough water!! I have pulled clothes out that havent even gotten wet, due to not enough water in machine! All due to the government regulated water levels on the sensors!!!! So, I had my plumber put in hot and cold water faucets, then he put a short Y hose on, so this way I can add water to the machine.... The only thing is, you have to wait for the machine to fill with what it thinks is enough water to get your load clean.... stop the washer, then add the water you need. But if it reaches a certain point, it will automatically start draining. So you have to watch and make sure you stop adding the water, before reaching that point!

Worst brand ever. They both broke at the same time. Spend too much money. Never buying these brand again. Maytag sucks. Dont buy Maytag washers or dryers.

Worst product I ever purchase. I have four kids which are boys. This washer does not clean very good. I usually soak the clothes first before I put it in the washer. Never purchasing their product again. Now I am stuck with this washer because I cannot afford to purchase another one. Hate it.

My old washing machine was about 25 years old but still doing a fantastic job getting the laundry done. When the dryer died we decided to replace both machines so theyd match. I had been setting money aside for years in preparation for this purchase. Ive only had them for two weeks and I stay awake at night wondering what GENIUS decided you can get clothes cleaner in a tablespoon of water than you can in an adequate amount of water?! My old washer could wash a load of laundry in about 20 minutes. Again, what GENIUS decided taking over an hour to wash a load of laundry in a tablespoon of water was a better way?! What working woman would choose to double the time needed to do laundry and then not feel confident that the clothes are clean?!!! I am so mad and frustrated and disappointed and I dont know what to do. I wish I could yell at somebody!!!

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

I purchased a Neptune washer/dryer front loader. All Neptune washers have basic design flaw over which the company should be sued. Since the bulk of the weight is in the front of the horizontal wash-drum, the entire assembly is suspended by a rear mounted bearing allowing the drum to spin. That bearing assembly is woefully under-designed and not able to support the unequally distributed weight that is inherent in any front load design.Since the forces of gravity cause a loading of the rear bearing on the front of the bearing raceway only, the machine is doomed to catastrophic failure of the entire drum system--and they all do this. When the washer goes into spin mode, it sounds like a jet engine taking off and that is a symptom of the bearing design beginning to fail which begins on the first use of the machine. The cost of the drum assembly/bearing and the labor is far more expensive than buying a new machine and therefore, not worth it. Avoid Maytag products at all costs.

I purchased the Maytag Atlantis Washer and dryer in 2004. I had the washer transmission replaced in 2006, I believe. For about a year now, the washer makes an awful screeching noise. I am not sure if its towards the end of the spin cycle or the rinse cycle, or both. In addition (and over the last 3-4 years), the dial sticks or stalls every delicate cycle. It will stop during the initial agitating and all you can hear is a ticking noise, in which you then have to manually give the dial a slight turn for the cycle to continue. It does it once on the light delicate and twice on the normal delicate. It really is a shame that Maytag is not acknowledging all of these problems as it is not feasible for most people to have a spare $1500 kicking around for a new washer and dryer every time they unfortunately buy a lemon. My previous washer and dryer were 25 years old and still working perfectly when I decided to part with them because they were fairly small. I dont even ever recall having any issues with either one of them in the whole 25 years that I had them. To see all of these complaints makes me more irritated with my appliances and my selection!

July 2011, I bought a top loader Maytag washer from Best Buy. In October, after I had the washer just a little over 3 months, it quit working. Dead. I called Best Buy that said they only stand behind a product for 3 months and since mine was about 3 months and 2 weeks old, I had to contact Maytag to fix it. When I contacted Maytag, it took them 3 long, angry, upsetting phone calls before they finally made an appointment for someone to come look at it the next week. I was without a washer for 9 days and when the man came, he said it was too new for parts. He would order a new latch (apparently, he thought it was not latched and so would not run), but it would take a while to get it in. Hed call me. 3 weeks later it and he showed up. He said apparently, the latches were bad because the new one didnt work either. He would order one more and if it didnt work, he would have to order a new back panel and it could take a few months, instead of weeks, for it to come in. The second new latch finally came in and the washer still did not work! However, he reprogrammed its computer to accept the new part and it finally worked. By now, it was the end of January 2012! My new washer I had paid for in 3 payments had been broken down longer than it had run! Best Buy said basically, you buy it, its your problem. Maytag said basically the same thing. They were hateful and it took over 10 phone calls to get anything done! I was not reimbursed for any laundromat usage, gas or phone minutes, of course! I was treated like I was expecting something that I had no right to have, a working product. Once I bought the product, it was my problem and not theirs. The end. I will never buy another Maytag product!

I bought a refrigerator from Home Depot in July 2013. In late November 2014, I noticed water on the floor in front of the fridge. I called the Maytag customer service and reported the problem.. The customer service rep explained to me that Maytag discovered a design flaw in the part that allows the water to drain when going through the defrost cycle. I also called Home Depot. Their response was it was my problem because the fridge was out of warranty and I did not buy an extended warranty plan. After two more calls to Maytag, they scheduled a service appointment. The service repairman told me the same thing about the design flaw. I have the old part and the package the new part was in. The two parts are completely different. I requested that Maytag or Home Depot replace the fridge or give me credit for the amount I spent. Maytag is now saying there was not a design flaw and because of that, Home Depot refuses to replace the appliance. I will never buy another Maytag product or shop at Home Depot. The extended warranty is a way to place the responsibility directly on the consumer and eliminating the responsibility of the manufacturer and the store.

Bought this Bravo washer from a Sears Outlet Store. Had trouble the first 2 weeks and did all the troubleshooting to no avail. Just when I was ready to return it to the store I decided to try one more thing. The guys who hooked it up had reversed the water hoses - cold was hooked up to the hot intake, and hot water was hooked up to the cold intake. Took all of 5 minutes to switch the hoses to the correct intake and the machine works like a charm. MAKE SURE THE WATER IS HOOKED UP CORRECTLY.

When my house burned in 1995 I purchased all Maytag appliances when we rebuilt because I had good performance from them up to then. My washer and dryer even made it through the fire and are still going now 14 years after the fire. They are 34 years old. The other appliances I purchased were a chest freezer, dishwasher, stove, and, a refrigerator totaling around $2,000, a pretty sum in 95. I have nothing but good to say about the freezer and the dishwasher, however, the refrigerator and stove stick me in the side every time I look at them. I purchased a smaller refrigerator than I had planned because I was PROMISED that the refrigerator was designed to hold the milk in the door. The first thing that happened when I opened my brand new refrigerator was the shelf holder broke and the milk fell to the floor making an awful mess. They ordered the shelf holder assuring me it was a fluke and sent me on my unhappy way. After I got the part I installed it and crack-smash-pow-swoosh! It happened again! I called the store I purchased it from and they said they ordered extras so to come in and get them, that I had probably installed it wrong. Went like this and I finally told him like I told him at first I do no want this refrigerator! You said and the pamphlet says it is capable of holding a gallon of milk in the door. It does not. It cant even hold catsup bottles without breaking. Thats when he told me that yes, they were having an issue with this refrigerators door shelves. He then gave me the rest of the shelf ends he had and said after that they were gone, they had discontinued them. Also said I was past the days to trade my refrigerator. I told him that was because he kept stalling me, ordering parts. LEMONS AND LIES. Now the refrigerator sits in my laundry room, freezes food in either section on its own whim, and the shelves are held on with DUCT TAPE. I have multiple correspondence with the company but gave up as I was seriously hurt in a vehicle accident and had to put my energies to surgeries and healing. And dont get me started about the stove. I will not be buying Maytag anymore.

Machine (Washing machine front loader model # MHW 5500 FC1) purchased August 2017. From the start Service Dept USA told me to unplug and re-plug anytime I had a problem as this problem started right away right after installation. In January it was getting stuck on the spin cycle. Unplug and re-plug to no avail. MAYTAG DO NOT have their own technicians just so you know. In the my area they use two subcontractors. In January they sent out the first sub-contractor from Appliance Wizards. He is a one man operation I later found out. As soon as he saw that I had a stacked washer and dryer he told me that this was my problem. He pushed a bunch of buttons on the machine, obviously re-setting the motherboard in a different way than unplug and re-plug and told me that there was nothing wrong with my machine. Not true. Machine was getting stuck again. Called Whirlpool service USA again. Told them not to send the same company. This time they sent JC Service. Excellent company. Kyle came out, identified that it was the motherboard. He claimed that they had other consumers with the same problem but that MAYTAG has corrected the problem and he went ahead and ordered a new motherboard. Waited 8 days and Kyle and another serviceman came and installed the new motherboard two days ago. Yesterday I put in my first load and the whole machine went dead. Kyle came again. He claims it is the motherboard again and he ordered a new one. I called Whirlpool service USA and spoke to Tina. All I wanted them to do is to ship my now, third motherboard quickly by courier so that I would not have to wait another 8 days without a washer. Her resolution was to extend my warranty by 6 months. I advised her that I had purchased a 4 year warranty but if they did not fix it so I can use it, even a ten year warranty would be of no use. So then she went and started reciting THEIR RULE OF LAW with regards to their protocol and told me that if needed they will replace my motherboard as many times as needed. She would not address sending the motherboard quickly. I asked for a supervisor several times and finally she agreed to put me through to the supervisor. She was worst than Tina. She agreed to check with the parts department and if possible she would ship it out by courier. I asked her to keep me on hold while she checked. She came back saying that they were not answering and that IN FACT they could not ship it out expeditiously. So, IN OTHER WORDS, SHE WAS LYING TO ME TO GET ME OFF HER LINE!!!! I asked her to give me the e-mail address of the EXECUTIVE OFFICE for Whirlpool. She claimed that she did not have their e-mail address and that the only way to communicate with them was by snail mail. I checked the internet and found a telephone number for the Executive office in Mississauga. I called them. The menu asked to push 5 for... get this... CUSTOMER EXPERIENCE... I pushed 5, followed by a bunch of beeps and a busy signal and disconnect. I tried 3 times. So there you go. This is their way of giving you a Customer Experience. Then I found a number for the Executive office in the USA. I was able to reach Latisha from the executive team and she assured me that if I were a USA resident she would have that motherboard shipped to be by courier right away. Because I am in Canada she was going to contact them to give me a call but that now I had to wait till Monday. 4 days to get back to me from Canada. Yet when it comes to service and parts, everything is arranged in the USA and everything comes from the USA because it is more cost effective for them. Who cares about the consumer. By then the motherboard will have left three days to arrive. 7 days take away 4 equals 3, take away a day for courier, depending on what time they call me on Monday, otherwise you have to take away two days, and then it will be all for nothing. But again, they must have so many complaints at the EXECUTIVE LEVEL, that they cannot call right away. So folks, note that Whirlpool has not recalled these machines with a defective motherboard, they are still selling them to unsuspecting consumers. They are not making an effort to send them out quickly or keep some in stock locally. BUT THE WORST OF ALL IS THAT THEY ARE REPLACING THE DEFECTIVE MOTHERBOARDS WITH OTHER DEFECTIVE MOTHERBOARDS!!!! This is outrageous!!!! I shall update my review once I hear from the very busy executive office for client care, and again once the new motherboard goes in. I shall post my order number and receipt when I update this review as my husband has all this and he is away. However I can give a work order number from service: **.

I have had my stove since 2004. A problem I have had was when I asked it to clean the ovens, it quit working all together. A service person was called. Also sometimes when I turn on one burner, another one will turn on instead. Yesterday I turned on a burner to low, and it did not turn on at all.

I purchased it 8 months ago. I have had problems with the machine leaving clothes soaked at the end of cycle. I have contacted Maytag (still under warranty) and they replaced the motor. The first load after repair still had the same problem. They said the check drain was not clogged. The snaked drain has no backups. After every wash, I have to reset the cycle to drain and spin. The machine spins for seconds and fills back up with water and doesnt spin again, but does drain. Clothes are sopping wet at the end of cycle. I contacted Maytag. They said I could be billed for customer education ($129) if they find no problem (threat). I want my money for purchase returned or at least 3/4ths. I expected my new machine to last years, not months.

I have only had this machine for 2 weeks after having a Maytag since 1994. Even broken, my old machine was far superior to this one, a Maytag Bravos. Fortunately, the salesman noted that I wouldnt be happy with this machine but, thanks to a government mandate, all new machines behave in a similar manner to save water and energy. This agitator-less machine neither washes nor rinses the clothes/bedding/towels properly. It takes four times as long to wash the items but doesnt get them nearly as clean. Today, I put 2 pairs of shorts, 2 T-shirts and a standard bed-sized mattress cover in to wash. The mattress cover never even got thoroughly wet even though I used the deep wash and extra rinse settings. Last week I put sheets in the sheet setting only to have them come out totally wrinkled and stiff as a board with soap even though I used the recommended amount of detergent. This is a disaster. Shame on Whirlpool/Maytag and the U.S. Govt. A river and a flat rock would work better!

All of a sudden, the lid lock light is flashing. The washer is only 1.5 years old!

I wish I had read the reviews before selecting this Bravos XL washing machine. I bought these from Conns Appliance as they were on sale 750. Rounded figure... They were delivered today and the company was professional and set them up, I have spent the last 4 hours washing the same medium load of childrens clothes trying to get them clean. Ive even separated them into smaller loads and am now into the 5th hour of laundering this same load... Im returning them but its gonna cost me 15% restocking fee. If theres a class action please count me in. I thought because our Maytag Neptune lasted so long wed have a great outcome again with these, boy were we WRONG!

Ive had other dishwashers over the years. Ive had this Maytag now for almost 12 years and never had a problem with it. It cleans better than any others Ive owned. HIGHLY recommend the Maytag.

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

Purchased Maytag Dishwasher Model MDB7749SBW3 in April 2014 along with other Maytag appliances to go into our home in the Georgia Mountains. Purchased Maytag for 2 reasons: 1. American made 2. Reputation. Bottom line, after just 2 years the dishwasher has failed. I prewash by hand everything that goes in. First the normal cycle stopped working. Then lights on front panel would randomly turn on and dishwasher would turn on by itself, and run for hours. I suspect this could be a fire hazard. I have tried front panel resets, cycling power, etc. Nothing works... It is really sad that American products are third world. I will replace the board myself in hopes of getting another couple of years out of it. No more Maytag for me. Rest assured every time I see someone in Home Depot or Lowes, looking at Maytag appliances, I will go out of my way to warn them.

I love the fact that there is no agitator in this machine. It give lots of room when washing bulky comforters. I also love the vast amount of settings for load size and the soil settings. The con of this washer is that it has broken down on us twice in the 2 years since we purchased it. The pump has gone out both times. Unfortunately it looks like we will be making a purchase of a new washer in the near future because another mechanical issue has arose.

I purchased this machine and after 2 loads it started making a very loud and awful noise. Maytag sent a local service person and he found a screw that had come undone and was in the motor. Since then there are a few strange noises that the machine makes during different cycles, usually involving spinning. Called Maytag and then sent repair person. This young man was non-verbal, was probably 20 and it was impossible to communicate and try to figure this out. Person sat through a full cycle and he said the noises are because the machine is out of balance. Well, why did the sync system not balance at the beginning of the cycle. No answer to that. He reported to Maytag that nothing was wrong with the machine.Machine is still making noises and I cannot wash a small load or it will still be wet at the end of the cycle. I am a widow and live alone. I dont wash large loads. So I called Maytag again. They dont care. Finally they agreed to send another 2nd opinion. I have a lot of videos of the machine making strange noises and the repair kid does not care...lots of blank stares from him. I highly suggest not going with Maytag. They dont back up their products and they leave you with a bad machine. My LG FL was perfect. Never an out of balance load. I could wash a single item with no problem. MAYTAG IS A TERRIBLE COMPANY.

We purchased a Maytag Dryer with the lint vent on top on March 21, 2014 from ABC Warehouse in Ann Arbor, MI. Whoever engineered this does not dry clothes. Trust me, this will be the last Maytag I buy. There is lint seeping out of the top and when you clean it the lint gets all over the place therefore, my laundry room is always full of dust.

Just read Ann of Colorados (posting April of 2014) message about her Maytag Bravo washing machine and its like I wrote it myself! Our Bravo started with making a loud noise during the spin cycle which turned into oil or a dark liquid spraying out from under the machine, along with saying UL, so I would adjust the load and get it going again only for it to start the spin and rinse cycle all over too! We have 5 people in our family and cannot afford to not have a working machine. We purchased this machine only a few years back to replace another product that was also a piece of junk. I guess as a last resort I will try a Spin Queen which is American made and hopefully will work! Very disappointed in Maytag. Whatever happened to Machines lasting like they did for our Grandparents?

Fire Hazard - poorly designed with vent at bottom of oven, Warped Drawer and Melted cabinet surface. Nowhere in the install instructions does it say not to mount above drawers. Whirlpool tried to blame dealer. Buyer beware.

I purchased 4 new Maytag appliances as part of a kitchen update. The dishwasher was the first to fail, less than a year after being installed. The control panel stopped working (random lights would come on, always different from the one being pressed, and frequently incompatible selections such as Rinse Only and Sanitize. PC Richards sent a repairman with a new part, no charge. A few weeks ago, it happened again. PC Richards says that replacement parts are only under warranty for 90 days, so now the repair is on me. I could pay or repair it myself or pay PC Richards to do it. Thank goodness I am handy, but I still have to pay for the part. Now I am reading that the MDB7749 series has a history of this problem. When is Maytag going to own up and issue free repairs? I certainly will never buy Maytag again, as both the range and the refrigerator also have common problems. Luckily, I paid for the 10-year service agreement on those appliances.

This dishwasher is at 10 years old, but is a real workhorse. This machine cleans like no other! Never worry about our dishes being clean. But we have replaced the seal once.

I purchased a Maytag washer-dryer combo in late July 2014. It wasnt until early August that we actually used the washer. It worked fine the first day, but the next day it would no longer fill. After following all of the troubleshooting instructions, I called Maytag to schedule a repair. They said they would locate an authorized tech to make the repair. I called back the next day and was informed that there was no repairman in my area and they would contact a service that contacts local repair techs. A few days later I called back to learn that they still could not locate a repair tech. I live near the New Mexico/Arizona border, and asked if a service tech could travel from Tucson, Arizona and was told that they could not cross state lines and, at that point there was nothing else they could do. They claim that I live in a remote area, but I reside near a major US Interstate (I-10). I will be filing a complaint with the BBB and my states Attorney General. It is now late October and all of my efforts have been ignored. I am totally disgusted with Maytags customer service.

Maytag Bravos top load washing machine - This is the worst washing machine I have ever used. Like some of the other complaints it leaves lint on your clothing. It does not put enough water in the machine. The so called smart technology that senses your load does a terrible job. Your clothing is halfway out of the water, with dry spots, even after 10 minutes of agitation. I am constantly adding 3 to 5 gallons of water to my loads to get things in the water. And if I want to let thing soak for a while you have to unplug the machine, because after 10 minutes it will automatically drain the water out. 2 years of dissatisfaction. I cant wait for it to die. I should have come to this site first. Never buy a machine without an agitator!

I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.

We purchased this Maytag about ten years ago. We had an old brown one that had to be 25 yrs old and still going. This piece of junk has had two compressors; the ice machine hasnt worked in a year, and now it just went out again (third time weve lost hundreds in food)!!!! About the same time we bought a Woods freezer on the cheap, this freezer sits in the laundry room crap piled on it and around it and never have had a problem. Maytag = $2500.00 boat anchor.

I have to rewash many load of dark clothing because pale white smears appear on the clothing most times. Ive tried various cleaning methods to try to remove any residue that might be in the walls of the tub. Unfortunately, I cant afford to replace the Maytag white elephant model 500XWZ, serial C31430894. I no longer have the receipt. Buyer, beware. No Maytags in my future.

Magtag Bravos Washer top load Model MVWX700XW1 - I purchased my washer in June 2011 with the understanding that this was the best washer for my money and needs. I have family of 4, and laundry is a continual cycle at our home. I had the washer delivered and installed by the store where it was purchased. I was pleased with the machine even though the clothes were extremely wrinkled after each cycle, but the salesman was kind enough to tell me this would be so. 21 months into use, I had a water leak from the internal cold water valve. It’s not covered by warranty; I had the valve replaced. Within 2 weeks, the machine would not spin out the clothes; if it did, they were still wet, or would stop mid-spin cycle and start rinsing again. It took 2 hours to wash a 37 minute hand washables load this past Saturday, 4/6/2013, not to mention the other 4 hours washing to regular loads just to get the machine to rinse and spin. The service technician has spent the past 2 days at my home trying to repair my machine to tell me today that it is not the lid lock, but the master control panel which is still not covered under the manufacturer’s warranty. To say the least, I now have to purchase a new washer as I have invested $250.00 for a valve and the control panel is $275.55 plus labor.This machine is the biggest waste of money that I have ever spent. I have been a loyal Whirlpool customer having owned two other Whirlpool machines, each lasting 17-18 years each. I do not abuse my appliances, overload or in any other manner try to destroy a machine for personal gain. I do, however, feel that Whirlpool/Maytag needs to recall these washers or cover the parts beyond what is written. I have read numerous accounts of these and similar issues by others, yet the company will not stand behind their appliances. Really!

Purchased Maytag 4000 series washer Feb. 26 2011 - within six months Maytag warranty replaced the drum and bearings, within another few months Maytag worked on the drum again. Year two started out with the warranty contract replace the drum and bearings again. Oct 1 2014 called for service again, the drum not moving and having to wait 2 weeks for Tech. to checkout the machine then order parts. I have 7 children at home and that didnt matter to anyone. After reading online the number of 4000 series Maytag machines with this problem somebody needs to make Maytag recall and replace them.

We purchased a brand new Maytag washer dryer and had nothing but problems with both. After talking with corporate several times, trying to reach the CEO, the customer service person told us that the problems were buyers remorse. Needless to say we will never purchase another Maytag/Whirlpool product as long as we live. We are going with Electrolux!

Hello, I purchased a Maytag Bravos washer model MVWX655DW from the Home Depot in June of 2017. I can provide the receipt. Within 6 months I had a broken lid switch and the unit would not move through the cycles. Luckily, I had the ability to replace the lid switch at the cost of about $100 just for the part. The repair was fairly involved. This summer, the unit failed to agitate, upon much research, I learned the washer drive hub (which makes the washer agitate and spin) was worn out. It was made of plastic and it is quite a job to get the cover plate off and to replace this part which ranges in price from $20-$45. This is a fairly difficult job and I would not recommend it to most people. It should not be needed in a 3 year old machine. Upon inspection of the drive shaft teeth when I took the washer apart, I found the steel teeth to have significant wear. Why? Now, in mid-November, same issue, the plastic drive hub is worn out again! I was told maybe my shock absorbers for the drum needed to be replaced as the drum may be shaking too much. My previous washer was good for 18 years and I replaced it with this highly recommended model Maytag with the chrome basket. This is absolutely the worst appliance I have had and with every repair, I viewed many, many people with the same complaints and feeling that Maytag should issue a recall on these machines. I will be contacting Maytag and Home depot with my review. The HD installer also stripped the plastic valve one of the water hoses goes on that I had also to replace. A $40 dollar part. This took some disassembly but not as bad as replacing the drive hub every three months. Needless to say, I have to buy a new machine after 3 years of unreliability with his machine. A waste of $500 + of my hard earned money. Very, very disappointed. If I wasnt mechanical and able to fix this washer, it would have cost me hundreds in repair bills. I have receipts of the parts I have purchased for this unit. I hope your experience is better if you have owned one of these machines. Maybe I just got a bad one but many people have complained about this model so I dont believe I am alone. I hate to see good people spend their money on poorly constructed machines. I certainly expected more than 3 years out of a brand new appliance. Maytag and Home Depot have lost a good, long time customer unless they want to make it right. Please feel free to contact me.

Lets see... my complaints are the same as the others. I purchased the Maytag Bravos set. They were the higher end units. At first, the machine was very quiet. I quickly had a control board go out. Got that fixed. Now the washer gets off balance on every load.... Every time it spins, it stop. The gears whine very loudly... Louder than any other machine Ive ever heard. I agree with the comments on wrinkled clothes. It also does not clean heavily soiled clothes as well either. Overall, a bad decision.

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

I purchased the Bravos XL washer and dryer combo 2 years ago. Dryer is fine, but washer was EXTREMELY noisy from day 1 and has gone downhill since. It would leak during spin cycle and frequently stop due to unbalanced load, refill and stop again. Now it wont spin at all! We have checked to make sure it is level, it is. I live in a very rural area and its very difficult to get repairmen to come out. This is my first and last Maytag for me.

My husband bought a washing machine in August 2019 and now it broke down a month ago. There is a sticker on it that the warranty is 10 years, but this warranty is for the motor and not for everything else. I read on the Internet what kind of error the machine gives me, it turned out to be either the motherboard or the front panel. I did not order the parts myself, called the service, in 5 minutes I had to pay 130 $ to he told me the same thing that I read in Google.... And he said that the repair would cost another 500$ part - 250$ and service fees to replace the front panel or the motherboard. Its ridiculous prices, so I find parts lil cheaper and ordered the motherboard myself, my husband installed it (there is nothing hard to do it) and the machine still gave the same error, I ordered the front panel for 220$ and the machine still gives the same error. Now front panel didnt respond at all, and this brand new panel... So I bet after I will pay to service they will tells me there is something else broken... Maytag??? NEVER AGAIN!So I send all part to the store, save money this way and now I buying a new one, when a year and a half ago I spent 1000$ on Maytag and the service is trying to rob me at the cost of a new machine, and no one gives me a guarantee after the service, I will not have a new one. The way out is possible to read more reviews and take a protective plan for 5 or more years so this is not your problem.

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

We purchased a Maytag front load washing machine and dryer about 5 years ago. The front load washer is completely full of mold even though I have always followed the directions of wiping it out after each wash, leaving the door cracked, washing the machine with Affresh and even trying bleach and vinegar rinses. When I called customer service they refused to do anything about it. Then the dryer stopped working after 5 years and we had to get it serviced. Now, the door has completely come apart, as in every little piece has come off the handle and surrounding door frame. I have never seen anything like this on the oldest of machines and I have taken care of these appliances. I will never buy another Maytag...

Bought a French door Maytag with freezer on the bottom. Ice build up on the bottom of the freezer and it has ruined my floor. We are replacing the floor in the kitchen. It is only a few years old. They have horrible customer service and will not replace anything.

The design capacity of the dishwasher is not conducive to cleaning a full load. Within 3 months of purchase one of the interior baskets broke. I will never buy another Maytag product again. I was a fool in believing this was a top of the line dishwasher.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

MF12269VEM7 - I purchased a refrigerator in September 2013 and my ice maker stopped working within 1 month of delivery. I had the motor and ice assembly changed 3 times and over 12 service visits within the first 6 months. I had the motor and ice assembly replaced in March 2014 and they offered to extend my warranty for a year. My ice maker has stopped working again. When calling Maytag customer service, I spoke to the Supervisor who will pay for the parts but require me to pay for the service calls. As well they only have a 6-month warranty extension on file. This fridge is obviously a lemon but they will not take any ownership because I did not purchase an extended warranty! The Supervisor state he does not report to anyone and he has the final say regarding my service. I will never buy a Maytag again. A year and a half of ongoing problems and no solution.

Have had it for 2 years now and its leaked out the bottom since it was 6 mos. old. Now the ice maker has fried a motor and were having to repair it already. Cant believe we spent a small fortune on this fridge and are having constant problems with it.

I purchased a new Maytag dishwasher model MDB7609AWB1 approximately 2yrs ago from Sears. We purchased quite a few new appliances from them and they are always helpful. Within the first year, right after the warranty was up, it stopped working. No lights on the power panel. I called Sears, out of warranty, sorry. Said they would give me a deal on the repair. Sears came out, replaced the computer. $230.00. 6 months later, it stops working again. I go on line to look up these models and sure enough a lot of people are having the same issues. I did some of the checks that they said to do and found my plastic door latch was broken. A little plastic arm that actuates the switches broke. Should have been made of metal. I replace it myself, very easy, by the way. So I figure, in another 8 months it will prob break again. They run anywhere from $19.00-$30.00. 2 days ago power panel and light, not working again. I called Sears and asked them if they were having issues with the power panels that this was the second time in less than 2 years, and if there were any recalls, they said no. I guess they dont follow their reviews, but according to google reviews, its a major problem with most of them. Maytag, Whirlpool, and Amanda. Ordered a new panel today, again they are $141 from Sears but if you shop, you can get a new one for less than $85.00. If you have any kind of mechanical skills, you can replace it in less than 20 mins. It just seems to me that this big companies have let their quality control go and are more concerned about the profit. There should be a recall on these. Do Not buy a Maytag/Whirlpool dishwasher, they are total junk. Sorry Maytag, you lost another customer.

1 year 4 month old fridge went out. Waited a month for part/repair. No help from customer service. $1200 fridge, $700, lots of angry calls, no luck. Customer service is horrible. Will never buy Maytag again. Someone suggested to take it to small claims court. Has anyone successfully done this? Any advice how to get my $700 back? Please email me **. Thanks.

Just passed warranty period and Maytag dishwasher broke. It would not start. Called and was allowed to purchase extended warranty for $135.00. A new panel was shipped and dishwasher lasted just under one more year with same issue. Another extended warranty was offered for $199.00. Needless to say we are buying a new dishwasher and not a Maytag or Whirlpool. The panels are notorious for rusting out. Hmmm moisture of a dishwasher and parts easily corrode.

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

After researching the top-rated washing machine in consumer reports, we decided to spend the extra cash ($930) and buy the top-rated machine. Spending almost double on a high end machine, you would expect this machine to last longer than three years. The motherboard needs to be replaced because it gets stuck on a UL code near the end of the cycle. Now, we have had two people come try to fix it, and they said to trash it and buy a new one. Only three years! If I had paid $300, I wouldnt be so upset, but that was a total waste of money for it to last less than any machine Ive ever had. How is a consumer supposed to know what a good washing machine is if they spend extra cash for the top-rated machine and that one is still bad? The company should replace something like a motherboard that goes faulty when it had nothing to do with use. So unfair and frustrating.

We purchased a Maytag refrigerator model # MSF25D2EAS on 10-22-2012 at the Home Depot in Tracy, CA. On 2-2-2014 (15 months) we noticed a puddle on the kitchen floor. Upon inspection, we noticed that the refrigerator was not working. Went over to Home Depot and were given the name and number of the authorized Maytag repair dealer (A and E). The technician arrived on 2-5-2014 and replaced the compressor on-off /overload relay and charged $243.82. On 2-16-2014 (11 days later), the same thing happened again. The technician came on 2-19-2014. This time, it was the compressor at a cost of $800.00 plus the $75.00 service call. One can purchase the compressor online for $300.00 and I am sure that A and E buys it for a lot less. We thought about it and decided not to get it fixed because we did not know what else would go wrong and how long would the second compressor last. We talked to the Appliance Departments assistant manager and were told that Home Depot does not give any kind of consideration and she had worked there for 11 years and had not heard of any problems. She was not telling the truth or she was not aware of the numerous negative customer reviews online. She also informed me that I should have bought a warranty. We have bought quite a few refrigerators in 50 years and they lasted for many years. Home Depot sells inferior products. Maytag must sell these inferior products at discounted prices and of course, some stores are looking for larger profits. I do not trust Home Depot any longer and will not purchase appliances there anymore. It was a very expensive lesson - the price of the refrigerator, loss of food (twice) and the stress it caused. We bought a new refrigerator at Sears and it was not a MAYTAG.

I purchased an over the range microwave (OTR), boxing day 2018. It failed January 2021. It worked great before failing. The issue with Maytag/Whirlpool is their service. I told them before they came out that I was only interested in having it fixed if it could be done that day. They checked that they had the parts and said they could do it, so I moved forward with the appointment. Well they didnt fix it, and said that they need to order a part, which they said would take several weeks. They are trying to bill me the service fee $167, and expect me to wait a month or possibly more to get the part and fix the microwave. Now Im faced with having to pay a service fee for something not fixed and buying a new microwave. Lesson: Never try to repair, cheaper to buy a new product. Other lesson, never buy Maytag or Whirlpool product again. Despite what is on their website and advertising, they have terrible customer service.

Same issues as many others here, had to replace the main control board a couple of months after the warranty period was up. Funny thing is though, I brought the old board into my local electronic repair shop thinking it might be worth getting it fixed in order to have a spare on hand in case the new one was also short lived... He told me he examined the board and there was nothing physically wrong... The problem he said was in the programming or firmware. Unfortunately, he said Maytag does not offer an update and there is no way to clone the newer version from my new board onto the old one so it was garbage. Seriously Maytag? Hundreds of dollars later in parts and melted groceries all because you wont issue a firmware update? Also have water leaking out of the bottom of the fridge late at night so Im never awake to troubleshoot it. Considering how sporadic it seems to be, Im guessing it must have something to do with the defrost cycle... Have to figure it out though as its starting to cause damage to the floor and leaking down to the basement :( Never again Maytag.

The problem with this dryer (MGD7230HW) is the sensors for drying time dont work. The dryer keeps going even when the contents are dry. Have to use manual timer to conserve energy. Not worth the cost.

It has all the features we like and use every day. Timer, lights, fan, built-in Above stove, use minutes or preprogrammed Turntable, quiet, white in color, easy cleaning. Easy to replace filter and light.

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

We bought the Maytag Aqualift cooktop about a year ago & are continuously dissatisfied with it, for several reasons: 1) the cooktop is a huge nuisance to cook on. The burners are either raging hot (causing boil-overs), or too cool to simmer. The boil-overs then require much cleaning with an expensive cleaning agent. 2) the oven, whether you use regular or convection, underheats - so you can’t tell how long the cooking or baking process will take, & you have to monitor the cooking process. 3) the so-called self-clean is a joke; the oven will not be clean unless you crawl inside & clean it manually. Overall, I’d prefer to toss this range in the trash. I’m a good cook, but I get angry every time I use this expensive, poorly- designed product.

MAYTAG BRAVOS WASHER - Biggest mistake I have ever made, like all the other complaints, washer does not clean the clothes. This washer and dryer are in our vacation home. Only used on weekends we are there, now the washer is broken, will not spin and UL light comes on, even with no clothes in it. DO NOT BUY!!! Like others have stated, we need to start a class action lawsuit against Maytag for fraud and knowingly selling junk.

I would not purchase a Maytag in the future. The top oven does not work, and one of the burners is semi functional. Considering I have only have the oven about 5 years. I am not happy with the the product. In the future I would seek other options, Maytag is not on the list of products for consideration.

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

Washer when using sometimes my clothes are full of soap residue. The screen did not turn on. After unplugging it for a few minutes it finally turned on. Dryer gives a warning to clean the airflow. I clean it and the error never clears. I use my swifter to clean it and I still get the error. I finally took out the screen and so far no error.

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

Both Sears and Maytag have lost my business FOR GOOD! We purchased a Maytag Bravo XL # MGDB980W0 2 years ago. We called within the 1 year warranty period via Sears, they sent a tech out then charged us. The dryer kept shutting off before clothes were dry. We thought the problem resolved, then reoccurred after the 1 yr period. Neither Sears or Maytag would stand behind the product citing it has been discontinued due to problems. Well... yeah, no kidding. We paid BGE energy efficiency company to come out and evaluate it. They tweaked the exhaust vent and cleaned out the duct, however, they said we needed a new sensor. My wife bought a new sensor, installed it, and the dryer still wont work right! (Shutting off prior to clothes being dry). BOTTOM LINE UP FRONT: I researched and bought a new gas LG dryer on sale at Home Depot and shelled out $849 unnecessarily thanks to shoddy product and lack of company integrity. DO NOT BUY SEARS OR MAYTAG!!!

Wish there was some way to secure all dishwasher under the cabinets better. It tips forward slightly, but gets caught on counter top, so it won’t fall over. The dishwasher itself is truly amazing. I love the stainless steel inside. I ensure I use the dishwasher cleaner on hottest cycle once a month. I have no odors. Both racks hold up well and the silverware tray has never given me any problems. I even like the thin little third top rack, which is where I lay my larger flat knives or spatula. As long as I use the finish dishwasher cleaner, the dishes come out sparkling. And a few times I have forgotten to fill the finish container, the dishes still sparkle. My teenagers do the dishes a few times a week. They don’t wash them off ahead of time. On occasion I have to pick a few pieces of corn or food out of the bottom, but the dishes still sparkle and the leftover food caught on the drain, well it looks clean enough to eat. I would definitely buy it again.

Front load washer. When load is done. Removing is one long string of clothes... Is a large load washer which I like. But you cannot add any items after you close the door. And you always forget something that needs washing.

Not only did I buy a Maytag washer for the brand name and trusted longevity, but because they were always a good product in the past. When my Maytag EZ-Epic washer drum failed after only owning it for two years, there was no effort made by any associate to cover this under any sort of warranty at all. To replace this part, I was quoted so much money that I could go out and buy a brand new one for the cost of the repair for this faulty part. I am extremely dissatisfied with the way I was treated because the so called product was out of warranty and I will never buy a Maytag product again. Shame on Maytag for ever selling off to such a fraudster of a company.

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

My Maytag dishwasher is not working after 1 years & 60 months. I called Sears, where I got it. Then, Maytag company. It looks like I need to spend $167 for an electronic controller (the push buttons will not turn on) if I do myself (I doubt if I can go it, but I can try). If not, how much will I pay a tech for coming (I was told $59) plus the labor if I let him fix it. So Im looking at a total of approx $400 plus to fix a 1 1/2 yr old Maytag dishwasher. Any comments Maytag??

Maytag Top Loading Washer-We bought this machine a little over a year ago and it is one of the worst products weve ever purchased. More often than not clothes barely get wet and then wad up into a twisted mess which stops the machine. Ive had to restart a load over and over. And, the clothes are not as clean as they were from our former Maytag washer which lasted 14 years. The new washer has to be cleaned at least once a month or it smells. We purchased this washer from HHGregg and they are no longer in business or I would complain to them about selling faulty products. I dont know why the manufacturer decided to remove the agitator from new models. What a mistake! We have decided to get rid of this washer and buy another brand. No more Maytag (or Whirlpool) products... ever!