Purchased an over the cooktop microwave 3 years ago, it came with a 20 year warranty. It stopped working and I promptly emailed Maytag customer service. It took them over 3 weeks before they responded. That is not acceptable. Did they think I had a back-up microwave to take its place until they finally got around to reply to me? Well we could not wait, and we just threw that piece of junk out and had it replaced with a competitors unit. We will never buy Maytag again and will inform anyone we know about the poor operation of Maytag products and lousy customer service. My suggestion to anyone considering Maytag products is to not waste your time and money and look to another manufacturer.

We purchased the Maytag Bravos MCT in July 2017. Just passed the 1 year warranty and the glass door just shattered. No reason for it really other than it must have been defective. Nothing dropped on it and it wasnt cold or hot in the room. I got nothing. Maytag said they didnt know why it would happen, and would have to send service tech out. A lid for this type of washer alone is $200-$300. Buyer beware. Dont get a glass top loader.

We purchased a washing machine, top loading washer model MVWC415EW1 on 9/2/2015 and the machine did not work right. 11/2/2015 is stopped working all together. It will not wash the clothes. The repair man says we need a new cold water valve. Maytag says it does not have the part to fix the machine. Period. Now we have a new machine with a 10 year warranty which does us no good as Maytag does not have the parts to fix. So it is back to a laundry mat until we can save enough to buy a new machine from anyone but Maytag .

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

Model MBF 2258XEW3. I am very annoyed with this fridge. Never will buy a Maytag again. I went to this site to see what the problem with my fridge was and read that I am not the only one with this problem. From the beginning it never worked right. Often the food in the fridge got ice crystals in them so I had to up the temp. This made the freezer not cold enough so I had to lower the temp again. This is a constant affair. Now the bottom of the freezer is collecting an ice sheet or a water bath that has to be removed every other day so that it doesnt built up or leak out. Will have to buy a new fridge. But now I am worried that I might buy another lemon.

I have owned two Maytag washers. Top load and front load. They have been the biggest piece of garbage I have ever purchased. My current front loader eats and destroys clothing. I have had to throw out numerous clothes as the machine simply destroys them. I have also had numerous problems with Maytag washers. The wiring is garbage. Couple yrs after purchase the washer shorted out. Im handy so I took it apart. Discovered a broken wire. I had to rewire a new connection with as. The wire used in manufacturing is so thin its line a strand of hair. Now it leaks under the drum. I had to place a container under the drum to collect the water. My other purchase was a top load. The lint was just a nightmare. Maytag sent me some contraption after numerous complaints that was suppose to assist in the collection of lint. Again, a piece of garbage. DONT BUY. Save your MONEY.

One baffle broke off in my washer. Very disappointed in this Maytag Model #MHWE201YW00 Serial #HL20102420. I purchased this in Sept 2012. Where the baffle was hooked on had sharp fins sticking out that ruined my 2 small rugs - shredded them.

I bought this machine in 2013 and within a year it had stopped going through any cycle. It turns off and I either have to restart a cycle or set the machine to rinse/spin. My clothes do not seem clean so I have begun handwashing them before putting them in the machine. I retrieve clothes and find some clothes dry. My towels have worn spots and threads pulled out. I cannot wait till I get a new washer because I am going to put this Maytag Bravos in the backyard and take a baseball bat to this hunk of junk.

I have a Maytag Bravos washer and on almost every other load, the dark clothes (mainly slacks) come out with white splotches on them and then I have to re-wash the pants and the splotches go away. What could be causing this? Im tired of washing clothes more than once. Its incredibly wasteful and bad for our environment. Thank you.

First the dishwasher - Control board no longer works. Seen many people with same problem. Dishwasher sitting there useless since cant afford to replace. Will cost as much as the purchase. Stove has defect between glass on oven door. Aqua clean feature is a farce and I feel vent at bottom of oven is asking for a disaster if any grease should spill in there. Maytag will not honor or admit any defects.

From the beginning, the blower motor (for the control panel? never needed one before) was too noisy. I just bought the oven from Lowe’s. They sent out a repairman. He replaced the motor, but has exactly the same level of noise. It is bad design/engineering. Im going to try some other brand. One problem is that you cant listen to the fan noise before you buy the oven and install it. And there are no decibel requirements or ratings. Industry regulations need improvement. Model MEW7527A, bought new in Dec. 2012.

Washer is noisy and water does not saturate clothes on normal wash. Have to use sheet setting for small or large load. Washer changes gears and it is so loud and clanks like something is falling apart.

Dishwasher control board has completely started blinking cancel when not touching it, ran for the entire time I was in Church. Numerous problems, only 2 years old. NEVER would I recommend this brand, EVER!!!

Pretty much the same complaint as Ive read about the Maytag dishwasher control panel issue. I purchased ours in Nov. 2009, issues began in April 2011, and service call for $129 where the technician said it needs a replacement control panel. I spent another $130 for the part and warranty on this specific part. In December 2011, issues occurred again. I ordered a new control panel in January and was told 3-5 days, called after 10 days and was told it was on backorder and should be shipped sometime in March. Youd think the Maytag President would be embarrassed for producing a product like this that in my eyes has tarnished what was a reputable household brand. Not that it will do any good but I will mail a letter to the President. One positive, our kids are learning to wash dishes the way I did as a kid, by hand. I sure hope the new control panel we hope arrives in March fixes this problem for good.

We bought a Maytag refrigerator serial # K11101146 and model # MBL2258XES1 on 5/7/2011. We started seeing puddles on the floor about a month ago coming from the bottom freezer. The warranty on the refrigerator was only good for a year. We investigated it further online and saw that a lot of other people were having the same problem. We found a video on Youtube on the solution, which was to tear the bottom frig apart (which is a pain and takes about 3 hours to complete) and to thaw out all the ice accumulated on the coils and run hot water down the drain until that thaws out. It makes a real mess. Now we see that this will probably have to be done again and again from others online who are having the same problem. We never had this problem with any of our refrigerators or any problem with them for that matter. Our last one was a 15-year old Amana and we wanted a more energy efficient refrigerator. We bought this one at Home Depot thinking that this one would last us for the rest of our lives. We are in our mid 60s now. This should not be happening at all especially as much as we paid for the refrigerator. I contacted Maytag and they more or less said, “Sorry about your luck.” I hope something can be done about this, especially for the amount of complaints filed. Unfortunately I did not take pictures but if it happens again, which I understand from other complaints that it will. Thank you.

Horrible machine. Purchased on 02/28/2014. I am 63 y/o retired housewife now. Machine used only for light washing, occasional king size sheets and weekly towels. I bought into the Maytag name, am so very angry that I did. Started a load at 1215 pm today... it is still sensing, washing, rinsing, spinning and then it starts all over again. Just unplugged from the power source, hopefully I can get the clothes spun out enough to dry!! Call and live chats to Maytag were frustrating to say the least. $400 plus Maytag service call to check out the machine not fix check out repairing would be extra. (I do not live in rural area, live 5 minutes from downtown Jacksonville FL!!!) Independent Repairmen will not touch this Maytag Model (cannot say I blame them!!). DO NOT PURCHASE A MAYTAG PRODUCT. This is a horrible company lacking in integrity, honesty and fairness. They sell shoddy, inferior products based upon past history.

If there was a zero star rating available, that is what I would select! We purchased this range along with a complete kitchen ensemble for a remodel of our kitchen in December of 2011. Within a few months of purchase the enamel finish started blistering, flaking and peeling. Upon contacting Whirlpool Corp about the problem through their online chatline, email, regular mail and phone, we were informed (quite rudely I might add) that Whirlpool does not warranty cosmetic deficiencies over 30 days after product purchase. This is American Quality?? Since this has occurred the retirement home we are building will have no Whirlpool Corp products in it which includes: Maytag, Whirlpool, KitchenAid, Amana, Jenn-Air, Brastemp, Consul, Bauknecht, Gladiator, or any of the product lineup from the Chinese company Hefei Sanyo which they are buying. The attached photos were taken in May of 2012 and since that time the product finish has only exponentially deteriorated.

My Maytag dishwasher is 1.5 years old and wont start. The Maytag call center said they couldnt help me except to sell me a service warranty for $269. Then she wanted to argue with me when I asked her to pass on my dissatisfaction with their products to her supervisor. I thought Maytag was a good product. For what I pay for parts and labor, I can get a new dishwasher. She said do I expect not to have any problems with that dishwasher. I will never buy anything Maytag again. They do not stand behind their products. Plus, it sounds like many people have had the same problem with their Maytag dishwasher. This part is defective. (I am assuming it is a control panel problem.) Since corporations are people now is there someone I push into my dishwasher so they will fix it. LOL.

Wish there was some way to secure all dishwasher under the cabinets better. It tips forward slightly, but gets caught on counter top, so it won’t fall over. The dishwasher itself is truly amazing. I love the stainless steel inside. I ensure I use the dishwasher cleaner on hottest cycle once a month. I have no odors. Both racks hold up well and the silverware tray has never given me any problems. I even like the thin little third top rack, which is where I lay my larger flat knives or spatula. As long as I use the finish dishwasher cleaner, the dishes come out sparkling. And a few times I have forgotten to fill the finish container, the dishes still sparkle. My teenagers do the dishes a few times a week. They don’t wash them off ahead of time. On occasion I have to pick a few pieces of corn or food out of the bottom, but the dishes still sparkle and the leftover food caught on the drain, well it looks clean enough to eat. I would definitely buy it again.

I bought a brand new Maytag bottom freezer fridge on Aug. 12th, 2012. The main compressor went out on Memorial Day of 2013. I contacted the store I bought it from; they referred me to a local repairman who fixes Maytag. I talked to him and told him the problem along with the make & model of mine. He ended up telling me what exactly the problem was, & there were about 5 people ahead of me with the same fridge, & same problem... all main compressor problems. Check this out. The compressor part is on back order... so now I have no fridge, & Im stuck with this piece of crap, until MAYTAG finds a compressor to ship to the local repairman. - Last Maytag product I will ever own in my lifetime!!!

Bought the Maytag MDSH969AWS1 in Dec. 2010, and it quit after 4 and 1/2 years. Ironically, replaced a perfectly good 20 year old GE model that ran great for this piece of junk. I tried to diagnose the problem: the washer fills, but when the cycle is supposed to start it just hums. Then you have to drain it. So I think the problem is the motor or capacitor. The parts are stupidly overpriced, and Im not even sure if that is the problem. It could also be the electronics board (Ive heard of the problems with these on this brand). So instead of risking wasted time and parts Im junking this, er, piece of junk. The stainless steel door was rusting on the bottom too. American made crap! Bought a fancy Samsung to replace it, and will NEVER buy Maytag again. Im old enough to recall the lonely Maytag repairman -- Itd give him a swift kick in the rear for being associated with such a shoddy brand. Maytag, its the Dodge-Jeep of appliances.

This is a wonderful washing machine. For cleaning clothes it does exactly what you expect from a washer. We have had 2 Neptune front loaders. They, however, have a couple flaws I dont want to live with again and will be looking for one that has come up with the solution to them. One, the bearings on them need replaced on a periodic basis or it sounds like a 747 taking off. Two - the front gasket around the barrel has a mold problem no matter how much you try to keep the thing clean. Other than that, these machines perform fantastic.

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

I bought a French door refrigerator on May 23, 2012. It is now July 9, 2014 and the repairman has told me the compressor is bad. Maytag will do nothing about it because it is out of the 1 year warranty. I am very disappointed because I thought I was buying a quality appliance. I will never purchase another Maytag appliance!

Failed after only 13 months with light use. I have a Whirlpool extended warranty which I had to fight to get them to honor. Then someone came to fix my washer and needed part was ordered, but part isnt available and company wont tell me when it will be. I have received 6 part availability dates so far. Whirlpool wont help. Over two months now without a washer. Ive asked them to replace machine or give me my money back, but they refused. The Whirlpool Extended Warranty group doesnt answer their phones, was put on hold for a long period.

I purchase my first glass top stove; a Maytag. It came with a 10 year warranty on all elements and the glass top. As this is a first glass top I read through all instructions, there appeared no real warnings on what to do to maintain the glass; or rather what would damage or void a warranty. I simmered some maple syrup, and as it so often does when reaching the proper temperature, it boiled over. On a regular burner, one just uses a little elbow grease and your stove is returned its previous state. This actually pitted the glass, and as the warranty people at Maytag informed me voided the warranty, and seriously weakened the glass top suggesting it would be likely to break. Seriously?????? All of us boil stuff over on the stove top from time to time, and this damages the glass top and voids a warranty??? VERY DISAPPOINTED in Maytags product and their warranty.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

Buy this washer! It has the best features! No matter what the setting, your clothes will come out as dirty as you put them in, only with even more odor! I just cannot believe how many different settings they managed to program into this washer, each one delivering the same miserable results. I am so happy that I spent so much money on a washing machine, that in some cases, doesnt even get my clothes wet. Truly amazing technology!

Worst experience of my life!!!! Don’t buy a Maytag washer!!! It’s agitating our clothes dry. Putting holes in clothes. We bought a warranty that’s pretty much useless. They will not replace. Only fix parts.

I purchased by Maytag Bravo from Lowes exactly 1 year ago when the gearbox failed. There was a loud grinding sound as the washer tried to shift from wash to spin. Reading through some on-line reviews and complaints it turns out that this is not a new problem and has been known to Maytag for some time. I specifically bought a Maytag because of their prior reputation for quality. Unfortunately, my information was out of date. It is so sad that a company would compromise such an outstanding reputation.

I love using my microwave because everytime I am in a hurry, like going to work and my kids to school and dont have time to cook or we dont like to eat outside fast food I cook healthy the night before and microwave it the next day and it just feels like the food is just made. It taste so good my kids and husband love it.

We bought a Maytag appliance package when we built our house in 2015. So far the exchange Fan burned out in the fridge. The element burned out on the range. The wheels broke off inside the dishwasher on the racks inside and the outside of the white dishwasher is rusting worse than 1959 Edsel. 3.5 years old. Broken and rusty. I called and emailed Maytag customer service and all they say is it’s out of warranty and they’re sorry. Things break I get it but if they said on the box when I purchased it that it would rust in 3.5 years I would have looked at and purchased another brand. Beware of the cheaply made poor customer service of the new Maytag.

My washer is less than 3 years old when I noticed the bleach dispenser has filled with water. I soaked the water out with a towel only to have it fill again the next time I washed. This in addition to the feeling I have that too much soap is left in clothes and spot removal is pretty consistently negligible.

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

I have a Maytag washing machine (MDBTT53AWW1). The total cost is $524 for machine plus installation. And the cost of yearly repair on this machine is $300.I purchased this machine a year and 10 months ago in January 2010. A few months ago, the control panel started to only light up partially but the washing machine continued to run. A few days ago, when i tried to turn on the machine, it would not work--the control panel was no longer lighting up. I called a repair man recommended by Lowes, and after explaining the problem over the phone, we scheduled a time for him to come (ten days later was his first available opening!).Ten days later with a broken washing machine and doing all the washing by hand, the repair man came late. When I made the appointment, I was told he would come anytime from 8 to 11 a.m., and of course, he did not show up until almost 1:00 pm. When he finally arrived, all he did was look at the model and determined instantly that the reason our control panel was no longer working was due to a faulty design. This dishwasher allows the steam to escape through a small vent placed to the left of the control panel. The steam inevitably causes a short circuit, meaning that this will be a reoccurring problem every year.He did not dismantle anything and was in my home for no more than 5 minutes. I was told the cost of a new control panel would be $141 plus his labor fee of $137. So all in all, if you purchase a Maytag appliance, the initial cost is irrelevant. If you purchase a Maytag appliance, you will spend almost $300 yearly to maintain it--basically the cost of a brand-new washing machine.Something needs to be done; this is unacceptable. The least Maytag could do is provide all of us, fools who believed in their product and thought that they were of quality, with a free10-year warranty for this faulty machine which is pre-determined to break down every year as a result of their poor design planning.Cost aside, what kind of world are we living in that major appliances are made to last just one year and then are to be thrown in the dump? There is no way I will pay $300 for the next ten years to maintain a product that is made to break. That is wasteful and disastrous for the environment. Shame on you, Maytag. You will be filling landfills around the country with your terrible products, and the world will be a worse place for it.

I purchased my Maytag Centennial 1 and 6 mos ago and it is already broken. The washer wont wash the clothes, just sit in the water and wont spin. I called Maytag, they offered me a warranty for another year for $371. The washer was only $550.00. When I tried to get set up with a repair service, the only company they used which was going to charge $105 just to look at it, would only take cash. When I called back to discuss with Maytag, they were no help at all. I was told they wouldnt even do the warranty since I scheduled a service even though I canceled it. I will never buy Maytag again.

We purchased all Maytag home appliances when our home was remodeled about five years ago. After the first year, the microwave had to be replaced because it malfunctioned. The dishwasher stopped working in the third year, and now, my refrigerator (model# mf12568AEB) wont cool. The technician told me that all of the Freon had leaked out because of a design flaw. Moisture had gotten into the compressor, and with the cost of repair or replacing the compressor, I would probably be better off buying a new refrigerator, preferably not a Maytag.

Rust on two year old Maytag Bravos washing machine - I noticed some rust along the inside lip of the washing machine lid and along the seam near the top of the machine about a week ago. I contacted Sears where we had purchased an extended service agreement. However, the agreement does not cover rust. I contacted Maytag and there is nothing that they can do either. The machine is kept inside the house in the laundry area. We have had two washers in the past 21 years that my husband and I have lived at this house that were much less expensive than the Maytag Bravo. They did not rust. This will be the last Maytag product we will purchase.

I got a Maytag Bravos 18 months ago and liked it at first. After using the washer for a while my towels were falling apart. Did not connect to the washer at first but I began to notice pulled threads on my towels. Talked to Maytag customer service who said they had never heard of the problem. She did say mix the towels with other clothes to prevent the problem. When I got this machine we had about two dozen good quality towels. Now I am down to maybe a half dozen. Those came from the six my Dad bought us for Christmas and I stashed away. The towels have pulled threads all over and will be completely destroyed soon.

My $1500 2 yr old Maytag mbf2258Dem refrigerator stopped cooling properly (wont freeze). The icemaker was the slowest I have ever had. That may have been the problem when I bought it. The Maytag Repairman came out and said that even with Maytag sending me a new compressor (under warranty) this unit was not worth fixing. I called Maytag and they said sorry there was nothing they would do. So l looked up every review I could find... and this refrigerator is just bad. Not Worth Fixing. So Maytag deceived me. On the front of the door it says 10 year compressor warranty. Thats a big sales feature! They know that they have a problem. This is one bad company!

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

For the first time I bought a new washing machine in order to have one that lasted. Bought a brand new Maytag Front Loading HE washer model MHW3505FW1. Controls stopped working and the machine turns on and off by itself. Its either a faulty control board or computer, either of which are going to be more than a $400 repair. So more than half of what we can pay for a new machine. Maytag only warranties two parts for more than a year. So in reality, its not worth the repair and I will not buy a Maytag of Whirlpool product ever again.

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

Maytag Washer 2016 HE top loader. This washer is horrible to use. I hate everything about it. After your clothes are put into the drum and you close lid to start here is what happens EVEN though I select deep water: it puts small amount of water in and then it agitates the whole big load. This is so stupid! Can you imagine a large load of your clothes agitating with a very small amount of water in the drum?So to get around that problem, you have to push pause button and shut the lid after your soap, softener and then listen until that first amount of water fills and agitates, then you have to push pause and quickly put in your clothes. Then you shut the lid and again push the start button so it will fill with more water. Then if youre lucky in at least an hour your load is finally finished. I hate this washer. My boyfriend bought it and I asked him several times to PLEASE return it. He didnt so now were stuck with it for God knows how long. The one good thing about this is I will know to never buy one of these for my house.

I purchased my Maytag Bravos Washer/Dryer several years ago, and I have hated them ever since. The clothes smell and are wrinkled. The dryer never gets the clothes dry. It will run and run and run, and the clothes will still be wet. I previously owned a Maytag Washer/Dryer for nearly 20 years and never had a problem. This set is a piece of junk. When I go to Lowes or any store for that matter and see someone considering this product, I warn them as quickly as possible to stay away from this product. I will continue to do so. Shame on you, Maytag, for making such a horrible product and for being too weak to stand behind your product. I will never buy Maytag again and will do my best to make sure none else does either.

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

Top loader Maytag Bravos type 588-03 - This washer is extremely slow and does a very poor job of cleaning. I use the recommended detergent (I use Tide HE) and follow the directions being careful not to overload. I can tolerate the slow operation I guess, but the poor cleaning is a real problem. When I put a plastic shower curtain in it, no clean happens. I just throw them out and but new every time. I will definitely go back to a Kenmore with an agitator.

We have had this washer for 1 year. I noticed right away my clothes would come out extremely wrinkled. Now not only are they wrinkled, they also smell musty. After researching I find others have the same issue, even finding a video of horrible mold under the drum. We called to have it serviced since we have a 5-year warranty. The service man recommended using Afresh. WELL, we do faithfully every month. He said they would not pay to have it cleaned, and even if he cleaned it, that the mold would come back. This to me is a major design flaw, one that could potentially make people sick. IF there is that much mold growing in the machine, with no way of cleaning it, and now the clothes are smelling, there is a HUGE issue!

I purchased this washer approx. 2 years ago. It will not spin. Called 3 repair men, only one would look at it. The cost to repair is more buying a new one. I am buying another washer and it will not be a Maytag. Seems from other post live on this washer is 2 years. My son has one just like it, told him of the problems. He is thinking of selling and getting another one before his quits. There are 5 in his family.

I purchased a Maytag 4-door model, a little over three years ago. A little over a year ago, I noticed small puddles of water around the bottom of my refrigerator on the floor. I blamed the dog for having accidents and shrugged it off. Well, after months of putting up with this I came to the realization that it wasnt my dog, so I started looking for leaks on the seal, etc. Thats when I realized that the entire floor of the freezer was one solid block of ice! So, I looked online for people that might be having the same problem. Sure enough, there are A LOT of us!!! Now to add insult to injury, I have to have a MAYTAG certified repairman come and look at what needs to be done! He only charges $85.00 just to come to my house!!!! Thanks MAYTAG, I spend $2500.00 for a refrigerator thats obviously defective, and still have to pay more to have it repaired!!!

I had two Maytag washers in my lifetime: one lasted 15 years and the other 20 years. Neither one had any service calls, just a sudden death. My newest Maytag is 1 year and 2 months old and Ive had two service calls so far due to the sensor unlocking the door. One time there were some socks caught “somewhere” and today the serviceman just reset the machine and it worked. He didnt know why it wouldnt work. It seems to me there needs to be some more detailed trials on these computer-operated machines. If I need another washer, it will most likely not be a Maytag.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

I bought the Maytag Bravo XL washer and dryer several years ago after reading many reviews. I like the glass top of the washing machine and the front door glass on the dryer. The dryer is fine its the washing machine that does not perform like the old machines. Whoever came up with the bright idea of saving water by cutting down the volume in your machine to about 6 inches for a good size load probably have never used a washing machine in their life. It does not get your clothes clean and does not get the soap out of a clothing to my satisfaction. Who made this suggestion? Could it be the same branch of government that made everybody use those spiral light bulbs years ago? The fluorescence that give off loads of EMF?

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

We have had our oven for seven years this past October 2015 and has now been down for three weeks. Last February 2015 (8 months ago) we had to replace the bake igniter because the oven would not get up to temperature. The most recent incident happened a few days after Thanksgiving (2015), I was cooking dinner and noticed that the oven was not reaching desired temperature. I then opened the door to see if it was hot inside the oven and when I did it must have ignited making a huge poof and flames came out at me! Thank God my 12-year-old daughter had walked away from cooking with me to answer the telephone because the flames came out exactly where she had been standing!!!I contacted Maytag and explained what had happened and how we could have had an explosion or someone couldve burned. The first questions they did ask me was if anyone was injured or any damage to our house?!?! I was happy for that however, it also told me that this has happened before! They called the Maytag repairman in my area and supposedly made it a priority call in which he could not come until 12/10 which was two weeks after this happened. Therefore, my husband and I contacted a different appliance man who came out and told us it was the temperature sensor. Since fixing it, the oven works ok and cooks properly however, when initially lighting/igniting it is extremely loud and makes a very large/huge poof! Its as if the oven is filling up with gas and eventually lighting! The other night when I lit it to show my husband it was so loud that it rattled the door and he immediately turned off the gas to it. I googled this and it said that its basically a mini explosion where the oven is filling with gas and then igniting! Its to the point that we could lose everything we have worked for just to make a meal! We spend over a thousand dollars on our beautiful stainless steel convect oven. Its gorgeous and when working works great however, Im petrified to use it now because Im scared to being burned or exploding! Now we start over and yesterday on Sunday I contacted the original Maytag repairman who said to call back Maytag again and hell come immediately. Maytag originally told me on the phone that they would cover labor and the service call however, ironically enough they did not write that in the dispatch order! Im outraged! What will it take before its safe for our family and home! My husband is ready to junk it and buy a GE however, we do not have the money especially before Christmas to do so. Oh and let me add that the first week we had the oven we had to call them for the window seal to be replaced because it was hanging. So now seven years after owning it and 10 months apart we are having major issues. What happens if its fixed and a year later it happens again? It could explode in our home!!! SCARED & IRATE WITH MAYTAG & WHIRLPOOL.

I purchased a Maytag Neptune Washer in 2006 for $665.00 from Sears. Three years later, the control board broke and I paid $400 to replace it. In 2011, the motor and motor board need replacing which will cost $410.00. We kept getting an LR code. So in 5 years, our repairs cost more than the original machine. Maytag can count on never getting my business again. Im only sorry that I purchased a Maytag dishwasher this Summer.

We purchased a Maytag refrigerator (freezer on top) model m1txegmyw00 in May 2012 and the compressor recently failed roughly 3 months from the two-year mark. We first noticed the issue this winter when the bottom level of the fridge start freezing our food. We adjusted the internal temperature setting down, but this did nothing. Then the compressor started cycling on/off for roughly 5 minutes at a time. After we noticed that, the freezer no longer kept things frozen. We called the Maytag repairman ($80 including taxes just to visit). He said the compressor is gone and that They dont make them like they used to. - I thought he was joking. He also recommended getting a servicing contract on a new fridge (but I would expect that from a serviceman). The cost to replace the compressor was over $600 and their work is only guaranteed on that part for 3 months (so anything else in the fridge could go wrong). I asked if we could have avoided this - he said it was possible that if we had unplugged the fridge for 10 minutes when we noticed the on/off cycling, it might have given the fridge time to reset (so take that for what it is worth). Our previous fridge lasted over 8 years - I dont understand how Maytag (owned by Whirlpool) can sell a high ticket item that will work for less than two years. I will not be purchasing another one.

My microwave is just 3 yrs old. SE error. Yeah, what a crock...Such junk. However, if we would just manufacture everything in the USA not only would we get better quality, but we would have more jobs. USA stop selling out to cheaper countries and pumping out more volume for less overhead.

We bought the Bravo XL set 11 months ago and the washer leaks all over the place.. Called Maytag and had the repairman show up. Upon arrival he told us these were the worst machines to buy and would never recommend to anyone. He also said that business has been great due to all of this.. He checked the washer and said the water pressure was too high and lowered it. He couldnt find anything wrong with it. After he left I started a load and sure enough it was the same. Called him right back and he said to call Maytag because he was going to another repair job. I called Maytag again and they said to call the repair guy.. Never again will we ever buy Maytag.

I purchased this Maytag Washer and Dryer back in 2000 and have never been unhappy. It really gets my clothes clean and uses a lot less water than a top loader. The only issue is that if you do not clean it once in a while it will start to smell, but I have a cleaner I use every month and so far (knock on wood) it doesnt smell mildewy.

I have a top load commercial tech washer with an agitator that is brand new as of September 2019. I have done all of the troubleshooting suggestions and nothing works. I use 1 tsp of liquid cold water detergent, deep fill, extra rinse, and clear liquid oxi and my darks still come out with white stains. I have had a Maytag tech check out the machine and it checks out without issues. I would never recommend this product to anyone!

Not only does dryer come with missing parts and are told by Maytag 1 to 2 weeks for delivery or drive 25 miles to pick up one. You do not qualify for rebate even though you do not receive washer and dryer for 5 days after rebate starts. Should have kept my old GE was faster and got clothes cleaner. Was looking at a Maytag refrigerator not anymore with their service.

Brand New 2019 Model 465 Washer and like others are saying is a piece of junk as they do not fill the drum with enough water even on the Deep Water fill option. The laundry does not circulate and nothing gets clean. Maytag is really poorly designed and manufactured these days and a complete Rip Off!

We bought a Maytag dryer from Lowes on 4.23.20 for $567.87. From Day 1, it required us to dry even medium loads at least 2 times and sometimes even 3 times. I have been complaining to my husband since we got it. The clothes come out smelling almost burnt. But if you dry it once, the clothes are wet. And if you try to dry it the 2nd time for less time, its still not dry. So, it takes forever to do laundry. This morning, it sounded like a lot of metal was rattling around. So, I looked inside to see if change was in there, and nothing was in there but t-shirts and socks. It had been drying for less than a minute, but when I opened the door a wave of extreme heat hit my face. Now Im afraid to use it because I think it will eventually burn our house down. And with COVID-19, we do tons of laundry. We cant afford another dryer but may have no choice.

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

I bought a Maytag Bravo without an agitator. Regretted from the 1st load. Some of my clothes do not even get wet and I bought the commercial grade. My 20 year washer that was on its last leg washes better than my brand new Maytag. Please do not waste your money, your clothes will not come out clean.

I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

We purchased this dryer a Maytag Model MEDC200XW3 about 10 months ago. The dryer slowly over time began to take longer to dry our clothes. After watching it work and seeing that the airflow in the tube was not flowing well, I noticed the lint trap was not functioning well enough and over 50% of the lint was escaping the lint trap and plugging up the exhaust vent. I asked Maytag for a service to repair my dryer and explained my findings. The service person on the phone wanted to send me a lint brush. I told her to send a repairman. The repairman said that all lint traps let lint by and said it was my problem. Well today theyre closed and I cant even leave a message. Now I know why the Maytag repairman is the loneliest man in town...

Bought a new Maxima washer in January. Worked for one week. Got error codes and electronics board shut down. Contract serviceman says board should have reset after turning off. Ordered new board and it is missing one of the electrical wire connector plugins. Maytag/Whirlpool is having a problem with these boards.Three weeks without a washer. Two days off work. When it goes out again, days off work will be close to what I paid for it. Thinking I may cut my future losses and buy another brand when in-transit board goes out.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

I purchased Maytag Bravos MVWX500XWO top loading high efficiency low water washer and it is a piece of junk. All my clothes came out horribly wrinkled and ruined a white jacket when I used the color safe bleach dispenser. I purchased the machine from Sears, where I purchased the extended warranty. I had an A&E technician out and he explained that the new technology of machines are expecting all clothes to be dried in the dryer. Okay, but what do you do with clothes that say hang dry and they come out so wrinkled and twisted that even an iron cant get the wrinkles out? Another suggestion from the technician, put the hang-dry articles in the fluff cycle of the dryer. Well, thats a big nugatory since they are supposed to hang dry them. Supposedly, this machine is all about energy efficiency but isnt it a contradiction when you are using more energy with running a dryer? Someone suggested to me that perhaps there wasnt enough water being dispensed during the spin cycle resulting in horribly wrinkled clothes. Either way, I am on my last nerve with this machine. I always thought that Maytag was an elite company. Well, how wrong I was! Their customer service is pretty much not customer-oriented. Its all about the almighty dollar. After speaking to a supervisor, she explained to me that I should contact Sears with my complaint that Maytag had no recourse. Well honey, Sears did not make the atrocious machine. They are just the so-called messengers. I have unfortunately found that once Maytag sells their horrendous product, they dont even stand by it. Now isnt that typical of companies nowadays and sadly, lacking with this company? Pride in their workmanship! And again, its all about the almighty dollar and who gives a ** about customer satisfaction? Maybe thats why they dont have the Maytag repairman. He was ashamed to be associated with this irreverent company.

We purchased our Maytag dishwasher (model MDB7609AWW2) on November 14th, 2009 from a local appliance shop in White Plains, NY. Total purchase price was $449, not including tax.Sometime in November of 2011, the unit stopped working. I tried every simple test I could think of to hopefully reset the unit. Finishing the obvious checks, I researched some possible problems on the internet latch micro switch, drainage problem, dirty latch, etc. Frustrated as nothing got it working again, I called a repairman recommended to us by the appliance store.The repairman charged me $75 for the visit just to tell me that the control board is shot. Even worse, and this is the reason for this letter, the part costs $329 plus $40 in labor! That is outrageous! If you do the math, I am facing the costs of a brand new unit to fix the old one. That might make sense if the unit was 8 years old but it is barely 2.I have sat on the decision now for a few days as I am beyond upset and I never make good decisions when I feel like this. But to recap, Maytag manufactures an appliance where its basic function - turning on - fails in 2 years and the repair cost essentially totals (to use insurance parlance) the unit. I find this absolutely unacceptable.I don’t expect Maytag to do anything for me. But I will say this; I plan on letting everyone I know just how this experience went. To make things worse, I am willing to pay for a quality unit but how does anyone know what that is anymore? For color, my grandmother has a KitchenAid dishwasher from the 1970s that is still running fine. No membrane controls, no delay functions or fancy BS super sanitary cycles and guess what, it has no control board, just plain old dials and buttons. Imagine that mechanical control? Built to last unlike the junk you see today.To remedy, I plan on picking up a used machine from the classifieds. I’ll install it myself and be able to do this for 9 years at $449, assuming it only lasts one year (I’m finding these units for $50 used). I may get lucky and find an old one from the 70s that will last a lot longer than that.

My husband and I bought a Maytag Bravos HE washing machine 3 years ago at Home Depot. It is by far the WORST appliance purchase we have ever made in 40 years! This machine started making horrible grinding noises about 6 months. It is not rinsing properly and its leaving detergent stains on our clothing. This washer needs to be recalled. I will NEVER buy another Maytag product, EVER!

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

I bought this stove thinking of the Maytag repair man commercial that was advertised on TV for washing machines. Apparently Maytag only knows how to make washing machines (I did not buy one of their washing machines after my experiments with their stove). From day one the oven door never closed right, the self cleaning oven device had to be replaced 3 times over the year after have a repairman tell me that they all fail. I stopped using the self cleaning feature. This stove has cost me so much in repairs. The cook top is very very hard to clean. It always looks dirty. All the plastic knobs have melted off because the oven door never closed right. And the knobs are crazy expensive to replace as is just about everything on this stove. The oven temperature can not be trusted never cooked at the temperature it was set at. I paid a lot of money for this stove 10 years ago. And I am finally able to replace it thanks to a Christmas present from my 3 children. I love to cook and this stove made it difficult. My advice is to look for a different company when buying a kitchen stove. This Maytag has been nothing but trouble for me.

Im very pleased with both the washer and the dryer. The front-load washer is very efficient with many washing options dependent on items being washed. Spin cycle spins very well which lessens the dry time of the washer.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

I purchased a Maytag refrigerator back in 2005; right around the time Whirlpool was making a play for Maytag. What a mistake! I had previously owned a GE that lasted 19 years! I even selected a model that did not have any ice in door or water in door that are prone to problems. In the 8 years I owned it, I had a serviceman to my place at least 4 times and dumped around $600 into it! Today the final straw... the compressor went! I will NEVER buy a Maytag again!

We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

The frontload washer 4000 series began making a very loud noise on spin. I called Maytag and requested service. The technician came and made a diagnostic evaluation, stating this has been a bearing defect affecting several of these models. I called Maytag, and the representative agreed to ship the parts at no charge. A week later, we received the parts, only for the technician to find one of the parts damaged in shipping perhaps. So another part was sent directly to the Maytag dealer. Upon my research, this appears to be a known issue with the Maytag/Whirlpool corporation, and I found where customers had requested Maytag to also be responsible for the service/labor costs, which were also covered by Maytag. I made the call today and was advised no and to be happy that Maytag paid for the parts due to a known defect and that no service or labor charges would be covered. I understand my machine is out of warranty, but this is a known defect; its nothing caused by my self.

The top of the range has blistered and has worn off. It cannot be cleaned. I spoke to a Maytag representative and was told to try and use magic eraser to clean around the burners. This did not work. The model number is mgr7775xs. Is there any solution to this problem. My range looks terrible.

This Maytag washer and dryer are far more superior than the units I had before. It is also made in USA which makes me feel like it will not fail me as soon as the others. The agitation when washing anything is something else I love. I will buy more Maytag in the future.

I have read all the complaints. I have similar issues with Maytag Bravos. I’m frustrated that modern tech products stink to high heaven, especially when we refer to clean clothes not being cleaned well. The specific issues I keep getting are the following: the LF codes appear and the cold water does not fill so that it wont rinse or drain. I have replaced the defective washers and that helped for one load. I refuse to fix it. Why throw good money out for the same bad product? I’m looking for a no bells and whistles washer or dryer that works. I have issues with the dryer, too. No more Maytag products in the future. Question: Who truly makes a good reliable product nowadays?

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

I’ve had my dishwasher for over 10 yrs now and I probably need to upgrade but it suits us just fine and I’ve really never had any problem with it at all. My dishes and especially my glasses come out Sparkling.

The best we can tell, we got our Maytag in 1991. This was because the repairman told us that was the last year they made parts for it. It ran wonderfully until 2018. The water valve broke, but a repairman easily fixed it. In 2019, it stopped running. The repairman fixed it, temporarily, he said. He refused to charge us for his work because he said we might get a few more loads done before it completely pooped out. Were still using it. I love this machine. It has gone WAY past the expected life span of a washing machine. Weve had it for 29 years!

My Maytag dishwasher (MDB7749AWM) stopped working at only 15 months. I had a technician check it and he said its the control panel not responding after he opened the door panel. Its when I searched online for replacement part I learned about the defective control panel. So I decided to forgo repair and bought a new dishwasher. I feel the manufacturer should be held responsible and called the number found on the internet, 858-646-8500, about a class action lawsuit filed in California federal court. The lawyer handling the case called me back that day explaining to me its a long road before the case qualifies for class lawsuit. Because I live in Texas, he will need someone to represent Texas plaintiffs in order to include Texas in the national settlement down the road. I said, I dont expect anything but would like to see a class action. Since I have no use of the defective dishwasher, he asked if I am willing to send the machine to him at his expense. I said yes. For all of you complaining about the defective dishwasher, I suggest you to call the number to join the lawsuit. Even though we may not see a penny for long, long time, its the only way to punish the deceptive business.

It doesnt agitate enough to move clothes around. Doesnt put enough water in tub, even on deep fill just barely gets to the top of clothes. Washed a shirt 3 times by myself to get dried mud off of it. 3 time it was washed bumy its self. Clothes do not to get as clean as they did in the old style washers that had good agitation and the agitator that was bigger than whats in these new ones. And water. Need water. We arent trying to dry clean. And even thats done with a liquid that totally covers clothes and moves around better than this garbage I have right now... Looking for an old washer to replace this one... HATE HATE HATE THIS WASHER.

Maytag Bravo Washer and Dryer - We are usually review writers. I just felt it was our duty to help others save their hard-earned dollars and not purchase this product. We have owned this expensive and highly researched set for a bit over 2 years. We have had to have repairmen out a half dozen times for dryer repairs. The washer was purchased with the largest tub because I wanted to be able to wash a full load of sheets or a blanket. NOT!!! It gets off balanced, twists every single item (as in blue jeans, towels, soft t-shirts, etc...any weight or size) into a huge mess and has actually ruined some of my clothing. The dryer gives me error messages all the time. I am beyond words with my disappointment. We saved a long time for this set and now are absolutely stuck for a long time before we can replace. You know Maytag my message to you is that hard-working people used to trust your company name. I have been married 43 years and we keep our purchases for many years. I have never in all these years been so disappointed in the huge purchase we made thinking it was a lifetime investment. Now I am doing everything I can to save this year so maybe can replace it down the road as soon as we can. I am telling you people reading this... DO NOT BUY THIS SET. IT IS A TOTAL WASTE OF YOUR HARD EARNED MONEY.

Maytag Quiet Series 400. Only good thing is the 3 spray arms. The racks are arranged in the worst configuration so you cannot fit many dishes in. The controls are extremely confusing. They do not seem to work in a logical way. The manual is of little help in figuring out how to operate the machine. I dont use the drying feature, so the only options on the panel that work together are Normal and Hi Temp Wash. Ive never had a dishwasher that took 2 hours to wash, but the settings dont allow for a smaller load or shorter time. The rinse agent receptacle is confusing and difficult to understand and use. Way too complicated compared to earlier dishwashers that Ive used. Would not buy this one again.

Front load washer unit does not respond to control inputs. I have called Maytag service and support. One can find a repair or maintenance manual. Im in a smaller market so there is limited service. Maytag service and online support is terrible. Maytag stores are fronts for independent service companies. Its probably okay, but misleading. Everyone wants to order the main controller board. It would be good to have a maintenance manual.

We purchased a Maytag Centennial washing machine from a local business here in Knoxville in 2013. My previous Maytag lasted seven+ years and I was very happy with it. It began to leak water and after two times of having water on the floor, we decided it had worn out and purchased another washer. We immediately wanted another Maytag since our previous one has lasted for quite a while. We bought the new Maytag Centennial washing machine in the Spring of 2011. This is May of 2013 and we have had to purchase another washing machine since the electrical board in ours went out. The replacement part is listed at $300+ and that is without labor to install. Needless to say, I am very unhappy that I have had to purchase another washer so soon... and did not buy a Maytag this time.

Always have bought Maytag. 16 years on both washer and dryer. The newer models, which I dont have, locks the top of the washer after it starts. I would hate that. I dont care if they are stackable but I would want full size. I dont think I would pay extra for a front loader, but the only front loading washer I have ever owned is small and at our camp.

I purchased a Maytag Bravo Washer and Dryer about 2 years ago; dissatisfied with the products. Washer continues to smell. I clean it all the time with the Affresh tablets. Usually, I have to use 2 bags just to get it not to smell for at least 2 weeks. Now, the glass front dryer is rusting out around the window.

A 14-month-old cabinet dryer required a new motor. I was promised delivery in 3/4 days. Following several calls, all of which resulted in the delivery date being extended to over eight weeks, the same engineer called to install the new motor. He refused to do it as the surrounding paneling had not been removed to give him access to the cabinet. It took another four days for him to return after we called in our builder to remove the panel--three screws and four-minute work. I asked for the warranty to be extended, by way of recognition of Maytags awful service. My request was rejected out of hand and the reasons do not accord with the chronological evidence I hold. I am about to bring a claim in the local County Court.

We purchased a Maytag dishwasher in January of 2011. Two years later the entire machine stopped working. We had purchased the extended warranty and the control board and panel were replaced. Now two years later it happens again. Maytag/Whirlpool is of no help nor do they care. DO NOT purchase their product!! Multiple complaints and issues with faulty control panels and the cost to replace one is the same as buying a new dishwasher so they cant lose. I will never again own a Maytag or Whirlpool product.

Horrific, useless, inconsiderate, rude, discourteous, arrogant and banal! I bought a brand new washer and dryer. The dryer is steam type and defective and they will not exchange, despite never being used. Nowhere am I committed to an agreement saying that the machine will not be replaced if it is defective. I am getting the run-around from the store, the manufacturer and the service technicians that didnt even arrive with tools when they came to evaluate the problem. If I had my way, I would return the washer and dryer and change manufacturers. But it is a stacking unit and I used the washer which commits me to it! Maytag, Whirlpool, JennAir and KitchenAid are all the same company. I am running out of options except going to the European manufacturers! Miele will at least install the appliances. They will be my next machines and I will not have to pay a plumber twice to install them the next time!

It doesnt clean as well as the cheap GE model we have at our beach cottage. Also it is very noisy. Disappointing. Will never buy a Maytag dishwasher again.