Maytag Bravo 300 Quiet Series - Bought this Maytag 5 years ago because Ive always had good experiences with them. After 3 years it started making rattling sounds so we had someone come out and fix it for around $275.00. 2 years later its still rattling, leaving black grease marks and putting holes in the clothes. Will not complete cycle unless it is unplugged, reset and plugged back in. I give up, I just bought an LG. I will never buy another Maytag washer again, still have the matching dryer though.

The washer does not get the laundry clean. It never has. I use only HE soap. I have changed soaps several times and still no change. I have been very disappointed with it. Maytag has been advertised as a good washer but the Bravos is not.

Bought the Maytag MDSH969AWS1 in Dec. 2010, and it quit after 4 and 1/2 years. Ironically, replaced a perfectly good 20 year old GE model that ran great for this piece of junk. I tried to diagnose the problem: the washer fills, but when the cycle is supposed to start it just hums. Then you have to drain it. So I think the problem is the motor or capacitor. The parts are stupidly overpriced, and Im not even sure if that is the problem. It could also be the electronics board (Ive heard of the problems with these on this brand). So instead of risking wasted time and parts Im junking this, er, piece of junk. The stainless steel door was rusting on the bottom too. American made crap! Bought a fancy Samsung to replace it, and will NEVER buy Maytag again. Im old enough to recall the lonely Maytag repairman -- Itd give him a swift kick in the rear for being associated with such a shoddy brand. Maytag, its the Dodge-Jeep of appliances.

Maytag Dryer model # MEDC400BW. I purchased this dryer in March 2015 the fuse went out in August. It is now November and it is out again! I have been buying Maytag since I left home at 18. I am 62 now, so I have been a loyal customer because Maytag was a great product. Not anymore since Whirlpool bought them out! You have to call them to schedule a technician and then it can take anywhere from 1 week to 3 depending on when they get the parts because they have to order them, and nobody else can come out to work on it if it is still under warranty! This is so lame and just not right.

Sometimes the control panel is difficult to work with especially if the wash is paused to add more clothes or detergent. The good things is that the tub is very large so a comforter can be washed and you can control the amount of water depending on the amount of what is being washed. I also like that it doesnt have the big agitator in the middle.

I purchased the Maytag MDB7749SBM dishwasher just over 2 years ago. After owning for 1.5 years, the control board malfunctioned. After discussions with Maytag customer service that began in late December 2014, it was finally repaired in February 2015, with the control board being completely replaced. Within just a few months the dishwasher again fails. The first time, it would not stop running. This time, it will not run at all. I called customer service today (August 1, 2015) and they expect me to pay for the repair.It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue, as the customer service rep indicated today (she said her information showed no recalls). Within two years I am now faced with paying $600+ for a dishwasher for a second time. This is terrible customer service on Maytags part. They have lost my business and I am warning consumers on every platform I have.

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

Washer breaks after 2 years. I purchased a Maytag Bravos XL washer from Lowes just 2 years ago. One of the main driving factors for the purchase was the Maytag brand. The repair tech just told us the bearing was bad and we need to replace this and the drum. The service call was $100 and the repair will be over $500. I can purchase a new washer for this. I strongly recommend not buying any Maytag product. The brand used to stand for quality but not now. I dont think the Maytag repair is still the lonely tech they used to be.

I bought a brand-new dryer Maytag Bravos. It broke after 3 weeks. They came to fix. A few months later, same thing happened, but I have 6 people in my house. They told me someone would be here the next day, and then that person canceled. They called someone else. He came and said I have to wait 3 days for parts. I called at least 6x and waited 30 minutes each time. They kept telling me theyd call back, and theres absolutely no call back. Then I called corporate Yvette, who was totally cocky and rude (866 817 5404). She said she would try to get back to me another day because she had meetings! Then, I was irate. I mean how rude. So she called me back and said, I ordered you the parts. Now you call Dan Marc, the service company, and make the appointment. Is this woman kidding? Then she went on about how Maytag has a 13% rating (They are Maytag.) and how their product is so wonderful. Now this woman is competent cocky and rude, and shes the presidents secretary! So whatever I call Dan Marc, they have no appointments Tom and wont make me an appointment. This is how a new product should work? I asked her what I do when it breaks again and again and the warranty is up. She told me they dont work on what ifs and if that time comes, it will be her decision. I am disgusted and have a house full of kids with no dryer? And I have given them another chance after that Neptune disaster. Im appalled and dont even know what to do.

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

Do not buy one. Maytag is unresponsive to repairs or parts that are needed. They are not even manufacturing the part that breaks. If you are lucky, you will find out there is someone who will fix the defective computer board... But Maytag will not tell you. We were without fridge for 4 months... They did not care.

Maytag WASHING MACHINE MVWC200XW - Will not clean our clothing. We have been tolerant of Maytags disregard for the people who have trusted their product and name over many years. No longer will we purchase a new Maytag or Whirlpool product. They say third time is the charm but I can not afford to take the chance. I wish them luck, they will need it.

We purchased the Maytag Neptune washer and dryer on May 2005. We purchased it for $2,000. We have had so many problems as we have replaced the drain pump 2 times because of objects getting stuck in it. We have also replaced the door switch, as well as flooding my laundry room floor several times.In 2006, we received a notice of recall. We responded to the recall and were supplied with a GFCI plug for our washer, as this was to prevent the control board from catching on fire. In September 2011, the control panel on the Neptune washer failed. I now have to purchase a new washer, as this is an expensive fix. With this poor workmanship and problems that we have encountered, I am very disappointed. This was a lot of money to spend on a washer, only to last 6 years.

Under class action suit in 8/2005, Maytag repaired my Neptune washer by replacing motor conversion kit. 6 yrs later the washer is having same problems as had originally; we asked Maytag just to replace the motor drive again ($190.00 part). They refuse, although this motor drive had identical life span to the one they replaced. It seems the replacement part was not new and improved, it only lasted as long as the original. Only now, we are past the class action suit deadline by years.

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

Hello, I bought a Maytag washer on 7/4/11 model #mvwc300xw0 serial # c12622108.I called Maytag about the machine not washing right, also the machine top and lid is turn from white to yellow. They had a service company come out they told me they should be replaced. I called Maytag and they told me the machine is only covered the first 30 day. This machine was made wrong. It started to turn color after a few months. Maytag told me they will not change machine because I Did let them know about the problem in 30 days. What can I do? Thank you.

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

After owning my refrigerator for about six months, it started to reek, the smell permeating all of the food in the fridge. After cleaning and disinfecting the fridge and throwing out all of the food I found that the smell was just as bad as before. When I checked online I found that Maytag owners have been complaining about the smell for over a decade now. It is caused by a poorly installed drain pan. The fridges design directs air flow so that the smell enters the fridge and distributes it evenly throughout the fridge.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

We bought commercial Maytag washer & dryer Oct 20th 2020. Very expensive ones. Oct 13 2021 they stopped working so had it checked. The shifter on washer went out & dryer blower is not working really!!!! Not even a year! Been without washer & dryer for 1 month because they didn’t have availability & now have to order parts another 2 weeks!! Never buying this product again!! Don’t buy Maytag!

The low water usage design is horrible. Clothes dont get clean as it doesnt use enough water to cover them. Takes twice as long to do a load as our old washer. Took about 1 1/4 hours yesterday for 1 load using heavy which is the only setting that uses more than a thimble of water. Should have looked for a commercial type with a real agitator and adequate water usage. Not saying Maytag is probably any worse than any other brand of new efficiency government mandated garbage washer, but its no good.

I purchased a matching set Maytag washer & dryer June 2013. Sept 2013 the drum went out - 4 weeks for that repair. March 2014 the electric panel went out. Took about 10 phone calls with hold waits of 30 to 70 minutes and 4 months, to find out the replacement part is no longer available and the washer is discontinued. To get a new matching set, I had to pay for a new dryer and they will give me a free washer. I have to give both washer and dryer back - I paid for 2 dryers. 6 month later and more phone calls, no washer and no one will return my calls. The dryer I paid for is at the appliance store waiting on the new washer. We consumers have nowhere to go. I have heard so many similar situations. Where are we to go? Who are we to call?

I purchased a Maytag dishwasher four years ago and it has been serviced six times in those four years. Not just small things, main parts. Control board twice, control panel twice, and cleaning terribly the other two. They replaced the control board once and then would not do anything after that. I just got it replaced four years into this nightmare only because I bought a Sears home warranty plan and they are replacing it. I would never buy a Maytag appliance ever again.

I purchased a Maytag Gemini gas range in July 2006. Rust has appeared on the bottom of both oven doors. I called Maytag customer service, realizing that my range was no longer covered by warranty. However, I feel the paint on a range, costing over $1,000, should last longer than 5 years. Customer service told me to call a repair technician. When I asked who would pay for this service call, they didnt even bother to respond to me. As I have read other reviews of dissatisfied Maytag Range owners, Im glad I didnt waste money calling a repair tech who would do nothing to help, but charge a $100 plus fee. The paint on a car, which is subjected to all kinds of weather, lasts much longer than 5 years. You would think the paint on an appliance inside a home should last much longer. This rust is becoming very unsightly. I will certainly not purchase a Maytag product again, as the company has proved they do not stand behind their product line.

I purchased a dishwasher and stove from Home Depot. Stove has already been replaced twice because of faulty manufacturing and now the dishwasher, after 1 1/2 years no longer works due to the control panel. I called a repair representative of Whirlpool/Maytag and explained the circumstances. Their own customer service people indicate that it is cheaper to replace a product then it is to repair it. Shame on Maytag and Whirlpool that they move their companies to countries outside of the United States and they no longer stand behind their product. Shame on them that what use to be the best product around is no longer worth paper you print on. I will no longer purchase any product from Maytag, Whirlpool or Home Depot since they all seem to line their pockets from products they know wont last. One mouth is worth a thousand complaints and I plan on screaming from the rooftops!

My husband and I purchased a Maytag Bravos washer and matching dryer in November of 2009. At three or four months old, the dryer quit drying and was emitting a weird smell and smoky air coming out of it. It was under warranty so a technician was called. A fan blade inside it had broken. The repairman replaced it and the motor as a precaution. There was absolutely nothing inside it that could have broken the fan blade and I always check pockets. My hoses were clear also. He told me that it looked poorly designed inside for air flow. He made a box out of sheet metal to fit inside it that he said would help it with air flow on the inside. I still have the dryer but I dont like it very much because it still doesnt do a great job of drying. It has to run too long and at too high a heat to dry laundry. The latch on the door broke a few months ago and had to be replaced too. I havent had problems with the washer as of yet. I like the washer and it washes very well but I will not buy a Maytag washer or dryer again. WHIRLPOOL OWNS MAYTAG NOW AND THEIR PRODUCTS ARE ACTUALLY MADE BY WHIRLPOOL SO I WOULDNT TURN TO THEM.

I purchased Maytag Quiet Series 300 Dishwasher in 2006. About 3 years ago, I got a letter that a recall had been issued due to an electrical problem. A service repair person came out and replaced the electrical element in question. Next the dishwasher did not work and a repair had to return again. Today I have the same electrical problem and after waiting on line 12 minutes to talk to Maytags customer service, I was told it could cost me a couple of hundred dollars to repair my 7-year old dishwasher. In my last home, my Kitchenaid dishwasher lasted 20 years before needing to be replaced. My daughters Maytag dishwasher lasted on 12 years. What ever happened to Maytags lonely repairman? I now have to get a new dishwasher and worry about my $3000.00 kitchen floor getting damaged with the removal of old and install of new. Believe me, my new one will not be Maytag.

I have just joined the open and close the door Maytag Club. Purchased four Maytag products on Black Friday 2017 as I always trusted Maytag. Only disappointed to have my microwave (MMV4205D-4) come down with the virus (open & close door) that has plagued so many unsuspected owners. Almost made its 1st year anniversary. Now I see this has been going on for years and all they do is add different model numbers at the end. Luckily Im in the 1 year warranty and repairman coming next week. Now I question if I should take the extended warranty as I see this is going to happen again down the road. And will the extended warranty cover it? Guess the Maytag repairman isnt sitting and waiting for repair call anymore. He is being kept busy!

I purchased an expensive front-load washer and dryer a few years ago. About a year after I purchased the washer, there was a foul smell that developed. I contacted Maytag and they informed me of the directions to follow - keep the washer door open when not in use and use Affresh tablets periodically. I followed these directions and was unable to prevent the washer from developing mold in the washer. Id like to file a formal complaint on my washer and dryer. I want a refund on it. I paid way too much money on these units to suffer. Here are the details on my units: Maytag 5000 Series with steam 4.5 cu.ft., Maytag Commercial Technology, Model: MHWE550WW01, Serial: CS00202582, Type: 199-02 732 WT/CR, 12 amps, 120 volts, 60 hz.

Have had the top freezer Maytag refrigerator for several years now, and it has performed great. Exterior is easy to keep clean, and the interior shelves come out easy for washing. Three drawers for fruits, vegetables and meat/cheeses work out great, and keep those products at the correct temperatures. Settings for both freezer and refrigerator are easy to see and change, if needed. Would buy another Maytag unit. Easy slide out for cleaning coils behind the unit.

I purchased the Legacy series washer and dryer from Home Depot in 2005. For the first 3 years, the washer worked fine. Since then, it has all been downhill. When I use bleach, I have to run an empty load because for whatever reason, the bleach goes through to the next load which has resulted in a number of ruined clothes. The wash cycle leaves clothes dirty and some even come out partially dry?! The rinse cycle does not always work as more times than not, the fabric softener is still in the dispenser cup. The spin cycle is getting worse with each load. Sometimes I reset the spin cycle as many as three times at which point I hand wring the clothes. This creates a strain on the dryer as I have to run it extra long to dry the clothes. I am more disappointed than I can say. I will never purchase anything Maytag again and I will not purchase from the company who makes Maytag products.

I got a new washer and dryer for my ex wife and son last August. Its October and the agitator broke off. She is not abusive to things and just the two of them dont produce much laundry. This was just poorly built. Maytag should be ashamed to have built such a poor product. I thought GE had the worst appliances, but Maytag must have hired their engineers. I have pictures and it has 10 year warranty right on the lid, lol. Should be 10 months,

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

Maytag Frontload washer MHWE300VW12 - I bought the washer and dryer in 2010 through Lowes. In Dec. 2012, it started making a loud sound when it would be in spin cycle. I called for service. When the repairman came out, he said the rear seal/bearing was bad and has gone out. The part and labor cost would be $1,184.36. Come on, are you flipping kidding me? Thats twice what I paid new for the washer. I bought them for the Maytag name. If I would have known it was a Whirlpool, no way I would have gotten them. My mother had a Maytag set that lasted 30 years. That explains why they dont show the commercials with the Maytag repairman that wouldnt have anything to do. Also, when the parts came in, they were Whirlpool parts. What a scam. Just more junk for our landfills.

I wrote the below to Maytag on their FaceBook page, of course havent heard anything back from them. Adding this on since I forgot about it, I have dogs and wash their blankets often, not that theyre dirty just for the dog smell. I have to wash them on the sanitize cycle which is an 1.5 hours long because if I use the normal cycle which is only 43 minutes they come out smelling exactly the same way they went in. I saw someone else post that their mothers front loader doesnt put in enough water so Im wondering if thats what happens to mine. So wish I would have checked the reviews before buying, thought I was getting a great washer buying Maytag.This is what I wrote on their FB page: I bought a Maytag front loading washer on 5/10/16 which was delivered and set up on 5/13/16. On Wednesday 10/19/16 it stopped working, so just over 5 months from the day it was installed. I called your company on 10/20/16 for repairs, they couldnt get here until today, 10/24, so 5 days with no washer. The customer service rep had all the details on what happened and Im sure passed them along to the repair company. He ran diagnostics, said it was the drain pump which was obvious even to me, but claimed to not have one with him even though they were in stock. Cant make it back until Wednesday, so two more days with no washer. He then proceeded to tell me that the dryer had to come off (stacked on top since the washer is a front loader) before he got back, that the warranty wouldnt cover two people coming out. So Im supposed to spend more money to hire someone to come out, take off the dryer and then pay them again to come back and put it back on. I called the customer service department again and was told they dont cover installation which stacking is. She said the warranty doesnt cover stacked units, as far as I can find that isnt stated in the warranty so please let me know where that is stated in writing. So I have a just over 5-month-old washer that needs repair already (bodes well for the future doesnt it??), will be without a washer for almost a week because the repairman didnt bring the most obvious part with him (maybe wanted to be paid for two calls?) and have to pay someone else for installation so it can be fixed. So wheres the Maytag man? I am not a happy customer and will be letting as many people know as possible. Ill be in the market for other new appliances soon, will sure as hell make sure theyre not made by Maytag, Whirlpool et all.

I bought a new refrigerator and when I plugged it in would not cool. I called and the authorized tech came and said the compressor was bad and the evaporator was rusted and hoses were greased up. I have now been informed that the warranty was void because it was put in a dental office and not a single home. I said since it was never used I would put it in a house. They said it was void and I was out of luck. I always thought maytag sold good products but this has convinced me to never buy a product from them again. It never worked and the tech said it should be replaced but they said he should never had told us this.

I love my new fridge! It has all the bells and whistles and looks/works great! My ice maker is the bomb! Best design Ive ever seen!

Maytag wont fix new washer. Service person came 3X, but it still wont go to rinse cycle. Last 2X Maytag said service scheduled, but no one showed. MT mgr said cant help & to just keep calling back.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

We have a Maytag Dishwasher Model MDBH949AWB. We have purchased the extended warranty. Today, after more than 100 minutes on the phone, mostly on hold, we were unable to schedule an appointment to replace the control board, or even have them verify that we have extended warranty coverage. It generally took many many minutes to get a person, only to be referred to a different person at a different number. Nobody had access to our extended warranty info, and to go further into getting a repair scheduled, they said they needed that info. I finally went on their website, and after keying in extensive information, I got a screen saying they were having trouble with their website, and to please try again later. So I did their chat, and ultimately they told me to call 866-730-6094. The earlier numbers I called, in sequence, were 866-576-1660 (53 minutes on hold); then told to call 866-265-0029, for another long hold. And then told to call 800-626-4342. Long hold, and I hung up. At one point, I think the second person I actually spoke with gave me an incident number of **. My extended warranty expires in Feb. of 2017, and they even asked me to renew early. Since the warranty seems totally worthless, why would I do that? Terrible customer service. Wont do business with Maytag ever again, and am warning others not do so either.

Purchased a supposedly top-of-the-line Maytag washer and dryer (9000 Series with Steam and MCT-Maytag Commercial Technology; Washer MHWE900VJ). Just under five years of use and the repairman quotes me just over $1000 parts and labor with the overwhelming majority of that quote being parts. No wonder the Maytag repairman is the loneliest guy in town - its not worth fixing your not-yet-5-year-old machine. It kills me that companies are allowed to advertise and promote the quality and reliability of their products and less than 5 years later, the machine is going to the dump, after having paid a premium for quality. This technology was supposedly comparable to what is used in a commercial setting - not very believable in my opinion. No more Maytag or Whirlpool for me.

This dryer ripped a gaping hole with sharp shards of metal exposed. It was working fine, and then it made a weird noise. It stopped and I assumed my laundry was done. We go to remove clothing and cut hand open on exposed metal. As if that wasnt bad enough, several hundreds of dollars in clothing had cuts in them. This dryer worked great for years, and out of the blue this happened. Im a widowed disabled mother, and cant afford a new dryer.

We had our kitchen redone by Home Depot in Sept. 2006. It was gutted and all was replaced: walls, heat windows, doors, lights, appliances. The Maytag refrigerator stopped working 7 years later. I feel an expensive appliance should last longer than that.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

We bought a Maytag Dishwasher Model # MDB4709AWW4 about 2 years ago. Complete piece of junk. Just spent $350 on a new control panel. We called Maytag and they told us that our model wasnt under the recall for this issue. The old belief about the Maytag repairman not being busy is a lie. Avoid their products. They are poor quality.

Purchased dishwasher from Highway Appliance in Dunlevy, PA on August 21, 2013. In August, 2015 control panel apparently went bad. When pushing normal, other buttons light up, but not the one you select. Tried throwing the breaker to reset, to no avail. Based on reviews, seems like many others have the same problem. Step up and do the right thing Maytag - recall & replace these machines!!!

Let me make it simple for you, DO NOT PURCHASE A MAYTAG/WHIRLPOOL product. Maytag/Whirlpool believes its products should work for 1 year and then become obsolete, at least this is what the Maytag/Whirlpool customer service line told me. I purchased a MVWB950YW (Bravos XL) top loader on September 4th, 2012 for $948.00 plus $99.00 for an extended warranty. The washer worked marginally well when it was brand new. June 2014, the washer in spin mode started to sound like a freight train was about to run through my house. When I called for service the service company immediately signaled it was a bad bearing and offered me $500 to put towards a new or refurbished Maytag!!! They claimed if they were to repair the machine it would VOID the extended service contract?? I wanted the washer fixed, I did not want to spend more money to buy a new machine. I continued to use the machine as is, with the incredibly loud noise. June 2015, the same machine starts to leak water and is even louder. Again the company in charge of the service contract offers money for me to put towards a new or refurbished machine. Net is, Maytag/Whirlpool engineers its products based on its warranty - 1 year. Anything after that they view as an opportunity to steal more money from you and I the consumer. Do yourself a favor and NEVER purchase a Maytag/Whirlpool product. I would like to think American products are superior to its foreign counterparts, however Maytag/Whirlpool is not in this league. In my opinion, Maytag/Whirlpool has lost the privilege to call itself American and should no longer be allowed to do business in this country.

We bought a Maytag dishwasher in May of last year. The control panel went out about 3 months after we got it. It just started doing its own thing Like not running the wash cycle or a different cycle than we pushed. We called for a repair and were told by the repair man that the control panel was on the fritz. He ordered a new one and told us it would be a month before he could come back and install it. When the control panel showed up at our house, we installed it ourselves because we did not want to have a faulty dishwasher running in the house.Just yesterday we noticed a huge rusty area on the bottom rack. We called and were hold for 20 minutes if not more, before we were even able to talk to a rep. She then came up with every excuse as to why our rack was rusty (hard water, water changing??). We asked for a new rack but she wanted to send a repair kit. We were on the phone with her for half an hour, if not more, and she just refused to send a new rack. When we finally asked to speak to the manager we were told the wait time was 32 minutes and hung up! Do not buy crappy Maytag appliances with even crappier customer service reps! (see our review about our Maytag fridge!).

Home Depot is selling defective appliances manufactured by Whirlpool and refuses to provide a full refund. I purchased a Maytag washer and dryer from Home Depot in August of 2010.Washer broke in February of 2011. No parts available for repair, Whirlpool replaced washer after 4 weeks. This washer broke in July 2011. No parts are available for repair until August 17th.

I bought a new washer and dryer on Sept. 9, 2011. Front Load Commercial 2000 Series. I have had Lowes to my home 2 times since it was delivered because it shimmies across the floor. I am very upset with the purchase of the Maytag front load washer. If you could please get back to me on what can be done. I would like for a representative to contact me and come and look at the situation.

I have a Maytag dishwasher and the rollers for the racks are failing due to heat: plastic wheels breaking up. $35 each to buy and replace. There are eight total. So $280 because of poor testing and quality of materials. Manufacturers should test to ensure the parts last a reasonable period of time and are designed for the environment in which they are being used.

We bought this Maytag Bravos XL machine in Sept 2016. It has never cleaned the clothes properly, you cant even tell they have been washed! It also shakes a lot. In January it shook so much it knocked a hose off, flooded my kitchen and downstairs bedroom. Home insurance had to pay to replace the kitchen floor and downstairs ceiling. We contacted Maytag. They said they dont have a repair person in our area. Home Depot wont take it back. We are stuck with no workable machine. We have to go to the laundromat and pay 70 a week for laundry, plus the time, and we are out all the money. We paid Home Depot (thousands) for a washer and matching dryer. Plus all the takeout we had to order while they repaired the kitchen, but the strain of this whole thing is ridiculous.

I have a Maytag MEDC200XW3 model. Good price reliable and rugged. It washes all the way from my delicates to my husbands heavy fire protective clothing with no problems. Holds lots of clothes with no issues either!

This is a Bravos MTC machine. It is a top load and has an energy star rating. Made in the United States. Impressed by its low water usage and Its ability to clean clothes. This particular model comes with a 10 year limited parts warranty, drive motor and washbasket.

6 week old High Efficiency Washer leaves lint and soap lines. Ive tried deep water wash plus the 2 rinse settings and I still have to wash the load twice to get rid of the lint lines and soap lines. Ive also tried every combination of settings to no avail and I follow the guide to a tee because this machine actually weighs the clothes to determine the water level. Maytag customer service was polite but useless. Im assuming its the poor design but customer service says I will be charge for the warranty service call if no problem is found. Maytag, another fine company down the drain. PS, parts are made in China.

We purchased a $500.00 Maytag dishwasher, Model #MDB7749SBW, in August 2013. In December 2014, a little over a year of owning it, the pump failed. We called Maytag and they had a service company come out and replace it. We paid $181.00 for this service call. In July 2015, the control panel failed so we called Maytag to see if they would replace it at their cost. All they are willing to do is to send another service guy out at our expense. The service call is $89.95 and that doesnt include the labor! The total with tax will be close to $200.00 again!!! Now we are getting close to spending $1,000 for this piece of junk! In addition, this dishwasher is only used three times a week because there are only two people living in our household. It is obvious after reading the other complaints that the control panels are defective and I am sure that Maytag is well aware of this issue. So, buyer beware. Dont even consider purchasing a Maytag dishwasher unless you enjoy watching your money flush down the toilet. They dont even deserve a 1 star rating!!!

Recently I purchased a Maytag Bravo Washer and Dryer. These two items are the single worst appliances I have ever purchased. They are loud, ball the clothes into a knot and run forever. I plan to sell them on Craigslist and buy a Speed Queen.

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

I give the Bravo T/L Washing machine and the Maytag company zero stars. I had to call for service 3 times within the last 22 months, twice for the electronic panel which needed to be changed, and the third time, it needing a new tub/drive shaft assembly at a cost of $405.27. I did receive a call from the Maytag customer service and all they would do is make a note of my complaint. I feel if you pay almost $1,000.00 for a machine it should work for more than 22 months. I believe Maytag manufactures an inferior product.Not only did it not last, my family and I found that the clothes didnt come out as clean as it should have, and sometimes, the towels would have a mildew smell to them after washing and drying. I assure you that I have read the enclosed instructions of how to use the machine, load the machine, and only used products designed for the machine

Just after a year the bottom freezer began to build up frost. I had to thaw it every day. A repairman changed part and ran well for about 5 months when it started to frost up again. Again, I had to call a repairman in. $500.00 later, my fridge is working again. I am done with Maytag appliances. Never again!

The Maytag Maxima XL front load steam washer is awesome. Its reliable and does an amazing job. There are so many features and settings and it makes my life easier when it comes to doing laundry. My favorite feature is the allergen setting which gets rid of allergens in my fabrics.

This washing machine worked great for just under 3 years. I noticed it wasnt draining completely. Per my appliance repair guy, the bearings were shot & it was going to cost over $300 to fix it. Called Maytag because my owners manual stated I had a 10 yr warranty. Wrong. The warranty only covers the wash basket & the drive motor. Look on Maytags Facebook page & you will see pages & pages of complaints on all of their appliances. Refrigerators, washers, dryers, if its got a Maytag name on it, its broken. Many of these appliances worked for only a year out two before they bit the dust. I went to Maytags fb page & ranted about their poor quality products & Maytags refusal to stand behind their products. Know what happened? They sent me an email stating that theyd reviewed my case yet again & there was nothing they would do. Then they blocked me on fb. Yep. Please please before you buy any Maytag/Whirlpool/KitchenAid product, please dont! Save your money & buy another brand. All Maytag will do is send you a form letter telling you they understand your frustration & you can email them your info, theyll investigate & get back with you. When (if) they respond theyll tell you theres nothing they can do. Basically you are sold, too bad, so sad. I now have a $600 piece of junk sitting in my garage. Im hoping I can get $20 out of it from the scrap yard.

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

I bought a Maytag washer 6 years ago. Energy saver. Less water. Nothing ever seemed clean. Always white streaks and I used liquid detergent. So we went out and bought another Maytag with agitator June 2017. Never drains properly. I will never ever buy another Maytag product.

Washer when using sometimes my clothes are full of soap residue. The screen did not turn on. After unplugging it for a few minutes it finally turned on. Dryer gives a warning to clean the airflow. I clean it and the error never clears. I use my swifter to clean it and I still get the error. I finally took out the screen and so far no error.

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

We purchased a top of the line, state of the art Maytag washer and dryer Neptune. The fill valve failed twice, flooding the first floor and the big storage room below. Thank God we were here! Now the thing halts mid-cycle and wont continue. The repairmen both said the design is messed up and they hate to work on the Neptunes.

It took about a year for the problem, which turns out to be an extremely common problem, to start. The build up of water in the freezer due to the clogging drain. Maytag needs to step up for the consumers that purchased their defective product. I have cleared the ice and tried to clear the drain three times only to have the problem return. I refuse to pay someone $300 or more to repair this. This is crazy and unfair!

It just keeps going. Still looks great. We have had our Maytag Neptune analog dryer for over 20 years. It has dried a usual 3 loads a day, with very little maintenance. We have replaced the motor, blower, and support rollers, but these are parts that were just wear and tear items, after years of extraordinary use. It has outlasted 3 or 4 washing machines.

Bad decision, Purchased in 2013 a Bravos by Maytag. After 3 years, it sounds like a jet engine taking off. The bearing is failing, sad as Maytag advertises to be the best. In 35 years, this is our 4th washer, actually the 1st was a hand-me-down that lasted longer. Unfortunately, we thought spending more and believing that Maytag would last longer was a mistake. Cost to repair is over half of the cost, so we have elected to run to fail. Then replace the Maytag that should have lasted at least 10 years. Warning. Purchase at your own risk. DO NOT buy this machine or any by Maytag, could be the same results. Or it could be that they are manufactured under Lowes specifications. From all the complaints the Maytag repair technicians are working, not setting around as they advertise. Only blaming myself for the purchase.

I made the mistake of buying a Maytag 2 years ago, this machine would not wash clothes even when using the deep water wash. I should have looked at it closer, it is so full of modern computer garbage that I was having to wash clothes twice so the water saving was negative. I own a business across from a major shopping center so what we did was we loaded it up in one of our trucks and parked it in front of our business with a giant sign and invited people to take a look before buying one. In 6 months we must have had at least a 1000 people inquire.

I bought a brand new Maytag bottom freezer fridge in May 2005. The first thing to go was the timing switch. I lost all contents of the fridge and freezer. The next to go was the compressor. Again, all the contents of the fridge and freezer were destroyed. This was after the 5 year warranty was complete. The cosat of repairs is around $800.00, which is the cost of a new fridge. I emailed someone from customer service, who replied how happy they are to hear from me, and how I can call anytime. I called customer service, and spoke to a supervisor. The fridge was built in the USA, but cannot tell me where the parts are from. No one seems to get, that I am disgusted that an appliance would last only as long as the warranty lasts. Oh, and the repairs are only covered for 90 days. My parents have a 62 year old RCA chest freezer that is still going strong. The lesson is, dont get rid of your old appliances. They may use a lot of energy, but they last. I will never buy from Maytag, ever again.

MODEL: MFI2265XEM1 - ice maker dispenser leaked water while under warranty; took two separate technician trips to repair. Several months later, called Maytag regarding leak and ice at bottom. Technician replaced w/ grommet w/ larger dia drain tube extension; smaller dia causing backup of water & ice. Now, ice maker quit working completely, ice buildup in bottom part of refrigerator and freezer building up frost which means air is getting into the freezer, and yes, the freezer door is completely shut! Please advise if there is a class action suit. Will contact California Attorney Generals office.

We bought our refrigerator 14 months ago and it has a 10 yr limited parts warranty. Both the freezer and refrigerator quit working, right after we spent $600 in groceries. I called the warranty dept and the soonest they could get here to service it, was 9 days later cause they only go thru Diamond Preferred, to do the repairs. Then on the 9th day, Diamond Preferred calls to let us know that unfortunately, they cant get here to fix it until another 5 DAYS!! Two weeks with NO refrigerator and freezer, is ridiculous. They should pay another repair place to come out instead of just relying on the ONE!! Our food is now ruined, $600 worth. And to top it off, weve had to eat out costing us more money, and then once its finally fixed, we have to go buy more groceries. I will NEVER buy a Maytag appliance, ever again!

I purchased a Maytag dryer (MDE2400AZW) 2 years ago, but have only been using it for the last year - and fairly infrequently, as this is a dryer that my guests use. I called Home Depot where I bought the dryer (along with the washer). I thought I had purchased an extra warranty, but turns out I only had it on the washer - what was I thinking. I wish I had read these reviews before I made my purchase. My local repair man charged me $192.00 for a new heater and his time. Theres a whole 90-day warranty on the new heater!! I sure hope this one lasts more than a year otherwise Ill be buying a new dryer and it wont be Maytag.

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

We purchased our Maytag® 4.5 cu.ft. White Front-Load Steam Washer online through Menards and picked up the washer on Feb. 5, 2022. We set it up on Feb. 6, 2022 and it didnt work properly from day one. The washer makes a clicking sound when it spins and also gets out of balance very easily. I contacted Maytag and they referred a warranty repairman in our area. He looked at the machine and said it could be one of two things and it would be a major repair. We would have to haul the washer to his shop and he would have to tear apart the washer to fix. He said it would be a big job to fix and we would be out of a washer for a few days.I also had contacted Menards shortly after we purchased the machine and they told us to contact Maytag. They wanted nothing to do with us and didnt want to stand behind a product that they had sold. Getting major warranty work done on a NEW washer makes no sense to me. I am very disappointed in Maytag and will never purchase anything Maytag again. Dont bother wasting your money like we did!

Purchased Maytag Bravos Washer in 2013. Used a little over a year and had to put it in storage for 2 years. Biggest piece of junk Ive ever had. Ive had cheap washers that lasted more than 20 years! Repairman said all diagnostics read normal. I put a very small load in to show him the water was not even wetting the clothes and only swishing them around a little. The shirt on top never got wet and was still in its same position when it went into the final spin. He said this is normal. He recommended I dump the machine and find an old NON Maytag model with the tall agitator!!! Ive tried using all the settings combinations; and the water level never gets all the clothes wet and clothes do not get clean. Will NEVER buy a Maytag product again.

We have had this washer/dryer stack up for about 2 years now. Not long after it was purchased from Best Buy, it started smelling like mold, even though we were doing everything possible to keep it ventilated. Best Buy employee said that service was not covered by the warranty that we purchased, so they suggested we YOUTUBE some ideas on how to get rid of the smell. They said it was a common complaint for front load washers. We have tried Affresh, hot water and bleach, hot water with vinegar and lavender, etc. Nothing is working. There is mold on the plastic inside the washer door and the stench is horrible now. You can smell it when you walk into our home. I believe that stench is the reason we are all having respiratory problems, allergies, etc. I just dont know what to do anymore. Really frustrating!! These appliances cost a lot of money.

Our washer ran great until last week. Had repairman in. User interface died after 18 months use. $250 for the part plus labor. This is a $1000 washer. Buyer beware. Maytag is just another name for any washer in the Whirlpool lineup. Uses the same parts. Has the same issues. Should have bought a Speed Queen.

I absolutely love this Maytag Bravos XL washing machine... I bought this machine before doing any research because of a sale and then after reading multitudes of reviews... positive and negative... I thought I had made a mistake. The absolutely most important thing with this machine is to load it properly and select the proper wash cycles. You must stack your clothes around the outside of the drum leaving the center open. You must use HE detergent. This is a Commercial grade washer and is meant to be loaded. The twisting and wringing of clothes is because of the high speed nature of the spin cycle (commercial). If you have never been to a public laundromat then you should try it and see what those machines do to your clothes. I too was apprehensive about the water levels at first... So I stood there for an entire cycle multiple time and on diff settings.The machine is constantly adding water as needed and each time after about 10 min... no matter the size load I put in. The clothes eventually were covered by water. Have had no issues with clothes that come out dry in spots. I suspect this is due to improper loading. Again my info on using this machine... loading techniques etc.. all came from positive reviewers stressing the importance of these key factors. This machine was not designed or intended for light or delicate use. So if you do a lot of those type loads perhaps this machine is not for you. As for the loudness and banging I have read about I have not experienced that. I have read reviews that the problem in some case ended up being metal or plastic drip pans used under the machine. Mine sits on concrete. Anyway hope this helps someone out.

Purchased Maytag dishwasher July 2013, installed August 2013. Stopped working Oct 2, 2014. Called Maytag and they offered to let me buy a service pan for around $300. No thanks, stupid Im not. I also sent an email. Have not heard back but Im sure Im still out of luck. According to the California class action suit regarding the Maytag control panels, Maytag is saying there are no problems with them. Wish we all had some power to make them see otherwise. Will I ever buy a Maytag product again. No. They would be much better off keeping their customers happy rather than spending tons of money on ads trying to get new customers. Since Maytag is owned by Whirlpool, they will not get my money either.

Purchase a Maytag washer in 2012 and less than 4 years later have to go shopping for a new washer. Purchased a Maytag because was under the impression that it was a good product and would last. Not true. The washer almost caught fire, just happen to be nearby when smoke started coming out from behind the washer, so I was able to turn off the machine and then unplug it and my husband smelt wires burning. If I hadnt been nearby we could have had a fire instead of smoke. I dont want to rain on anyone parade but I wont be recommending this product to anyone.

An average refrigerator/freezer at best. I would not recommend it unless you also buy a service agreement to fix things that go wrong with it. Ice maker went out.

I purchased a Maytag Centennial Commercial Technology washer in September 2010 which is less than two years ago. It decides to stop spinning correctly in the Spin cycles. Clothes come out sopping wet so I contacted Maytag to have a tech come out. On the day that the tech came out from A&E Factory Service, he stated it was a switch. He changed the switch and still, it did not spin correctly. He then proceeds to state that it is another part, which again, it did not do the function correctly. He then proceeded to state that it is the clutch, then the transmission. The cost was raising to $519.00.I stated that I did not want to proceed because I would be purchasing a new washer with that quote. I stated to place all the original parts back onto the washer. He did so, but did not place them on correctly. The casing of the washer no longer is secured to the drum - bolts and plastic pieces are still on the side. He left my house with finger prints of grease on the walls. If this is the workmanship that Maytag recommends, then my business deserves to go elsewhere.A complaint was filed with the A&E Factory Service. However, no one has contacted me about the complaint as was requested. All I want is for my washer to be fixed or to have a tech who is knowledgeable to come out and fix it. I contacted Maytag to inform then of the situation and they stated that all their techs are certified. I do not believe that my washer of less than two years old could possibly have so many parts that are faulty. I hope that this may, in turn, help another consumer to avoid purchasing washers through Maytag and their parent company, Whirlpool.

I purchased this $857 dishwasher from Lowes in May, 2021. It broke in June, 2021. S&S Repair was sent by Maytag to repair. It took 3 weeks for them to come, then they discovered the motor and pump assembly had gone out. Parts were on backorder. It is now August, 13, 2021 and I still have no dishwasher. Lowes would not replace this dishwasher. Maytag will not authorize a return. This is disgusting.

Purchased 4 Maytag kitchen appliances - stove, double oven, fridge, dishwasher - was told that they were all made in the USA. WRONG. The microwave comes from China - not sure why Maytag is not being honest. Not happy with my purchases - even though we spent $4000 to buy American. Warranty service is awful - even extended warranty is a joke. Would never purchase Maytag again.

I purchased a Maytag 2000 series washing machines. It broke and needed to be repaired within six months of purchase. It continued to break and need to be repaired numerous times and its only a little over 1 1/2 years old. It ripped and ruined clothing on numerous occasions. It would not drain and the door would lock with clothing inside thus ruining them. Both of these issues occurred on more than one occasion. Maytags solution for their defective washer was to keep referring me to my warranty. They were no help at all. My warranty finally came through for me and I was issued a full refund through the warranty I purchased at the time I purchased the washer. My new washer (which is not a Maytag) is being delivered Friday. So finally after being without a washer for over two weeks I will be able to wash clothes again. My experience with Maytag was frustrating and aggravating to say the least and I will definitely never purchase Maytag again. They are far from reliable.

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

I have had 2 Geminis. The first one was fine, this second one is a mess. I have had at least half a dozen parts replaced. I have insurance to have this oven repaired but have paid to have the window seal replaced on at least 3 occasions. The top of the oven is so hot that when I have used the burners to cook on top I have received 2nd degree burns. I have received burns on several occasions. I asked dealer if I could trade this in but said I would have to sell it on my own. I would not subject this oven to another person as I feel it is very dangerous.

I, too, am absolutely done with ANYthing Maytag. We purchased our Maytag microwave model MMV4205DS-1 in January of 2016. Within the first year we experienced occasional open/close door issues due to the faulty door latch switches. Now it happens virtually all of the time. The ten year warranty is a joke; it is just a come-on designed to deliver a false sense of security that Maytag will indeed stand behind their worthless products when in fact they wont. I am so disgusted with them.

The worst wash machine Ive ever used. It doesnt clean clothes well. It constantly had error codes. Im constantly having to unplug and reset the machine and 4 times out of five it will NOT restart. Not to mention it stinks worse than my sewer. I have to run the refresh cycle every four to eight loads. Ive owned this machine three years. And it has been three years too long. I will go back to a ringer washer or a wash board and have better results.

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.

I loved my first Maytag combo unit and when that quit I bought another Maytag. The Neptune is a front load washer. I immediately noticed the door gasket getting moldy. I contacted Maytag whose response was leave the door open. Well, I did that and not only did I still get mold, but the light burned out. I recently started having trouble - the water doesnt drain and the clothes are still wet. Rather than have it repaired, I elected to buy a new washer/dryer unit. I would NEVER again have a front load washer and certainly not Maytag.

This is probably the worst place ever to buy any appliances. They are extremely unreliable and the technology on them sucks. If you wanna buy new appliances I highly recommend you spend your money elsewhere. The customer service is extremely horrible and is a disgrace. Shame on this company. They lie about when they will repair your stuff too, so dishonest and I hate this company.