My daughter purchased this washer and matching dryer as a set from Lowes about 4 years ago. It was one of the few with an agitator and that is what she wanted. After using the washer for the first time she was very disappointed to find that the shortest cycle took over an hour and that the locking lid feature couldnt be bypassed. A few weeks ago the washer began gushing water onto the floor which flooded the basement below. She had purchased an extended warranty which was due to expire the following week.She called Lowes and scheduled a repairman. He finally came 2 weeks later and used the Internet to help him diagnose the problem!!! We could have done that. He decided that the control panel was only allowing the agitator to turn in one direction during the wash cycle. So essentially it was spinning a tub full of clothes and water causing lots of water to overflow the tub onto the floor. Needless-to-say he had to order a part and cant return for over 2 weeks to install it. IF this is even the problem! He also said he couldnt disable the locking lid feature! If my daughter had been able to open the lid when the problem started she would have known more about it.We are thankful her machine was under warranty but she will have been without a machine for almost 2 months when and if it is fixed. This is completely unsatisfactory for a gently used 4 year old washer. The dryer takes forever to dry also. If you are buying Maytag based on how long your grandmothers machine lasted, you will be disappointed! This washer caused so much damage we had to file a homeowners insurance claim!

Fifteen months after purchase, the lid lock and motherboard goes off. It was replaced with new parts and the machine still doesnt work. Cost of repair is equal to the cost of the machine. With or without an extended warranty, the expense is not worth the investment. While shopping to replace the machine, the dealer finished my sentences on Maytag washers.

My dishwasher was bought December 2013. The control panel just started going crazy and cant control anything. Unless you have bought extended warranty Maytag isnt doing anything. This is obviously a manufacture defect and no one is doing anything about it. Will no longer buy Maytag products if they cant stand behind their product.

Dryers been installed for 3 months, 3 service calls to date. Heat unit failure. 1st service call no show, no call. 2nd service call fixed the problem 50%, the dryer would heat on timed dry but no other modes. A week after that call heat unit failed again on all modes. Awaiting 3rd service call. Customer Service Department at Whirlpool Canada could care less. Avoid this product, Maytag 2000 series dryer - do not buy.

We purchased a Maytag washer/dryer 5500 series in October of 2006. It was working good for the first few years, then gradually started failing on us. The clothes would not be clean or they would be soaked when done. Two days ago, on the board it kept blinking LR. So I checked all measures to make sure that it wasnt the motor or the front door lock. That door lock is a big pain! However, it happened to be both the motor and the bearing at the same. This is definitely not worth spending another $700 on. Goodbye Maytag, hello LG!

We paid over $800 (more with installation) for this quality dishwasher. Within one year we began to experience problems with this unit. The top control panel easily becomes water logged causing the device to fail.

We bought a Maytag dishwasher in May of last year. The control panel went out about 3 months after we got it. It just started doing its own thing Like not running the wash cycle or a different cycle than we pushed. We called for a repair and were told by the repair man that the control panel was on the fritz. He ordered a new one and told us it would be a month before he could come back and install it. When the control panel showed up at our house, we installed it ourselves because we did not want to have a faulty dishwasher running in the house.Just yesterday we noticed a huge rusty area on the bottom rack. We called and were hold for 20 minutes if not more, before we were even able to talk to a rep. She then came up with every excuse as to why our rack was rusty (hard water, water changing??). We asked for a new rack but she wanted to send a repair kit. We were on the phone with her for half an hour, if not more, and she just refused to send a new rack. When we finally asked to speak to the manager we were told the wait time was 32 minutes and hung up! Do not buy crappy Maytag appliances with even crappier customer service reps! (see our review about our Maytag fridge!).

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

I purchased a Maytag Neptune Washer and Dryer at Home Depot for over $900. Within months, the board went out. The repairman said that they didnt even know how to fix it yet - no training. The board was out again. This time, it was not under warranty. The repair costs $779 including part and labor. There were numerous other little problems along the way that we did repair, but now, forget it.

Maytag Dishwasher model MDBH989AWB3. The dishwasher was purchased at Home Depot March 19, 2010 in Hollywood, FL; delivered to our new home April 16, 2010 in Brunswick, ME. My complaint is the exact same complaint as the previous 28 complaints! I think the reason our unit worked for 6 yrs is because it was in use only 6 months a year. My experience: you make your selection, two lights come on, you press start, but nothing happens. You think this is a simple repair. You read the manual and try their troubleshooting advice, but to no avail. When you contact the company, they tell you that this is going to be an expensive repair, probably over $500. You contact Home Depot who want nothing to do with you or your dead dishwasher. Their advice: contact the Maytag company. You contact local appliance repairmen and they will repair it at a cost of over $500. You offer the unit to the repairman for free; he declines. He suggests you check the online Consumer Affairs site. It is on that site that you realize the dead dishwasher belongs where one brings other dead things: the dump. I will NEVER buy another Maytag product. I would suggest no one else does either, unless you want to practice your skills in dealing with frustration or you want to throw $693.40 to the wind and watch it flit away helplessly. Thank you for reading this.

This dishwasher was here when we bought our home. It has been heating up way too much on the drying cycle. I turn it off and air dry the dishes but today I noticed it melted my plastic measuring cup. I had the heat turned off and opened it as soon as it started the drying cycle.

The dishwasher turns on of its own accord. Sometimes when you get too close to it, once in a while in the middle of the night, and most of the time when you latch the door. It does a great job cleaning the dishes, but to no avail because its always in the middle of a cycle when you need them.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

Last year we replaced a Maytag dishwasher which had a faulty control panel after just a few years of light use (There are just the two of us). It was going to cost almost as much to repair it as to buy a new dishwasher, so we opted for an $800 model (MDB8959AWW6) with a control panel across the top of the door. There had been a recall on that first Maytag for the heating element or something, so we decided to put the credit towards a machine that would last us for years, we hoped!We have been in this house for 18 years and the original cheap builder-installed dishwasher lasted for 12 years. In fact, there was nothing wrong with it when we replaced it with the last one. Whatever happened to the lonely Maytag repair man? We did not buy an extended warranty, but I can see now that probably these things are only meant to last the lifetime of the warranty.We are semi-retired and cannot afford to have the dishwasher repaired, so it will be a decoration in the kitchen from on. Never ever will I recommend Maytag to anyone! One bad experience should have been enough, and we probably would not have bought a Maytag again had it not been for the credit we got for the product recall on the last one!

I purchased a beautiful Maytag dishwasher for $700+ and it died after a year of use. I called Maytag to complain and they dont care. Pay $350 for a tech to come fix its warranted for a year or fix it yourself. I fixed it myself for $180 and am hoping the very same key panel wont fail again. I know it will. I wrote to Maytag about the issue and have not gotten a response. Im hopeful that they will make this right or that they get sued and the consumers get their money back.

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

Food freezes in the refrigerator. If I turn it down, the freezer does not freeze. What has happened to the quality of Maytag? This unit is so new. I think I am going to take it back and buy a better brand!

This has nothing to do with the vendor. This is clearly shoddy workmanship on the part of Maytag. I bought this refrigerator in 2005 and already the compressor is gone. So therefore, I have to replace the whole unit.What kind of ** is this? You mean to tell me that you people cant find someone to build a compressor that holds up more than a few years? Why dont you try American made and built.I am disillusioned by the whole industry. Im sure the people at the top could care less.

I wish I had read these reviews before purchasing my dishwasher. I have used it 40 times max. The control board went out. They want 307.00 to fix it. Really? Why would I fix this piece of crap when I can buy a cheap one for that price that would work better. Ridiculous! I paid good money for this dishwasher and the warranty that comes with this is a joke. Save your money and brand from a company that stands behind their product.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

Purchased a Maytag French door freezer underneath refrigerator 8 years ago. It stopped working because of the circuit board located behind the ice and water compartment on April 7th. Contacted a Maytag repairman, which is a whole other story. Had to order the part, weeks and weeks go by telling us the part is coming. Then a call came from the repair man on June 17th, Maytag no longer makes the part. Meantime we located the part by taking the fridge apart ourselves and ordered it arriving today June 19th. Contacted Maytag - Whirlpool corporate. Answer, We are sorry we no longer make the part, and basically told me after spending $2800.00 8 years ago Im up the creek without a paddle.

I have had and worked on many washing machines over the years. The worst design and complete failure of parts to easily align in Maytag front end washers is nothing short of staggering. Creating a tension wire to wrap a rubber seal that requires Hercules to install and easily tears the rubber is beyond ridiculous. Avoid front end Maytag washing machines like the plague since they may cause it given the mold and growth from excessive moisture when the seals tear.

I just bought this refrigerator a bit more than 2 years ago. I have to change electronic module for $300 CAD including labor. Home Depot advised me to contact directly Maytag and to express my dissatisfaction about this unreliable product.

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

We bought a Maytag refrigerator (single-door) with a top-loading freezer that failed after four years. The freezer began to ice up and two repairmen from the company that does the extended warranty repairs in the Ottawa area were unable to figure out the problem. After the second visit, the freezer iced up again and the thermostat appeared to be failing. Even though we had an extended warranty, we just gave up and went to a different dealer to buy a new refrigerator that could be delivered within three days - and it wasnt a Maytag or any other of Whirlpools brands. If youre thinking of buying a Maytag refrigerator, you should reconsider. In fact, you should twice before buying anything made by Whirlpool.

Weve only had the machines for about a year, but so far they operate perfectly. However, the washing machine seems to take much longer to operate than my prior machine and is much noisier. But, the cleanliness of our clothes is great!

We purchased this double-oven range (model: MGT8775XW01) about 5-6 years ago. It came with some slight bubbling on the plate that the control knobs go through/are mounted onto. A few years later, the bubbling paint began to chip/peel off - revealing rust (its a white range). I bought some touch-up paint, but that didnt look very good. Now that entire plate is bubbling and peeling and makes the whole range look like crap. My wife swears well never buy another Maytag product...EVER! Shes ripped! I cant seem to find the replacement part to purchase. Lousy products!

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

Purchased side-by-side with bottom freezer 2009 after Hurricane Ike. Fridge has stopped cooling. Called Maytag Customer Center and was told nothing can be done only to find theres a 10 year warranty on the compressor. This malfunction should not be an issue after 8 years. My GE fridge still works after 25+ years. Horrible!

I bought a Maytag washer 1 year and 1 month ago (MVWB835DW1), Hated this washer since day one. It does not wash clothes very well, does not even cover them fully with water. The mini agitator at the bottom does not move he close it just spins on the bottom of them. Now it started making a very high pitch squeal when it spins and of course it is one month past the manufacture warranty so I call a repairman and the first thing he says to me is Im sorry for your purchase, it was a bad one and it will cost me 600$ to repair because the bearing is bad. And my bad for not getting an extended warranty but I have never had a washing machine work this bad and break within the first 13 month of owning it??? Lesson learned I guess!

Washer goes off-balance even when clothes are evenly distributed in tub. When it is turned off to rearrange clothes (which may have to be performed a couple of times), washer goes back to starting cycle which means more water. Afraid to do laundry unattended.

I purchased a Maytag Bravos washer almost three years ago and I have been unhappy with it the whole time. I have not had to have it repaired but its performance as far as actually washing clothes and being user friendly are terrible. My clothes do not come clean at all, the tub inside the washer collects any dirt or grass and I have to wipe it out. The inside of the washer smells terrible and I have to keep using fresheners (never had to use them before in 50 years). The cycle time is ridiculously long and only varies by a few minutes from a single item to a full load, I will never buy another HE washer.

The dishwasher doesnt clean and the dishes and silverware come out greasy. What a piece of crap.

I have an MSD2542VEB01 model refrigerator purchased slightly over two years ago. I have the same problem as many others, which is the plastic breaking on the shelves. The first time, it was within a year and the part was under warranty. It is now a year and a half later and one is broken beyond use and another is cracking again. Maytag refuses to help me as there is no “recall and the plastic is not available separately from the easily removable glass of the shelf. The least expensive price that I can find for the shelf is $107 and I need two of them. $214 (plus shipping) when all I need is two pieces of plastic? Be very careful when selecting your appliances.

I bought Maytag washer 15 months ago and the washer is now leaking from the bottom. My floor was damaged from the leakages. I have not use the washer much in the past 14 month because its just me in the household. I will never buy a Maytag product.

Sears washing machine model # mvwx500xwo - This machine is the worst. My mother who is 87 years old smells like mold every day due to the smell that comes from this machine. Im not sure whats going on but the plumber told us there is something very wrong with this machine. Its not the hot or cold water that smells, its the machine. I am now concerned about my mothers health. Please advise if you will allow us to purchase another machine with some kind of a credit due to the serious issue this machine has.

I purchased a Maytag washer the centennial commercial technology model about 4 years ago. At the just barely 2-year mark it needed an all new transmission (Approx $800) Thank God for extended warranties. Now it is doing the same thing again making terrible noise. For a purchase of $1000 this is not good quality or decent workmanship And Maytag does not stand behind their product. I guess I need to buy another brand from now on. Please beware of very costly repairs with this one.

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

Washer would stop right after it started. I googled the problem and found out it was a bad lock. These Bravo XL units were purchased in 2015. Called an appliance repair and they charged me $250 to replace the lock (service call was $98.00 and labor was $90). The repairman left and I started the washer. There was a loud sound coming from it. I called the repairman back and he said it was the gear case and basket. He said the basket was covered under the warranty but the gear case wasnt. Would be about $750 to fix....no way was I paying the cost of a new washer to fix this less than 4 yr old one. I called Maytag. They couldnt help me. I should have purchased an extended warranty they said. The cost to purchase the extended warranty is now $394.00 per year....please do not purchase a Maytag/Whirlpool appliance unless you like buying extended warranties.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

I purchased a Maytag Bravos 5 months ago. I had trouble at first with unbalanced loads. The repair man came to look at it twice. One thing that can unbalance your loads is if small pieces of laundry such as a sock gets outside the basket. Sometimes the basket has to be taken all the way out because small pieces can be lodged under the basket. This happens when you fill the machine too full and those small pieces float to the top.The suspension on my machine ended up needing to be replaced. I have read lots of reviews about soap rings in the clothes. That happens from using too much soap. Make sure you are using HE detergent for one. I cut way back on my soap and my laundry gets clean and no problems with residual soap on my clothes. I was very unhappy with my machine at first but now I absolutely love it!

We purchased a Maytag washer and dryer from Lowes in the summer of 2016. The washer performed so so. Not a great machine. After only two years use, there is only my husband and myself, the transmission went out. The repairman said it would be cheaper to buy a new machine than repair it. Maytags 10-year warranty does not cover the transmission. We replaced the Maytag washer. I cant say anything good about Maytag.

The refrigerator works well. No problems. Easy to move to clean behind it. Good value. I havent had any problems since I bought it. Keeps a steady temp; Its exactly the size I needed; has plenty of space. Its a plain fridge with a reasonable price!

I had no issues with my washer. The best thing I ever did was stop using Sabrina softener in it and made the switch to vinegar. The worst thing I ever did was think that paying $900+ for a nice washer would get me more than a year! What a joke! I started noticing small leaks when my hardwood floors started lifting and once my husband looked into this, we realized there is no seal around the top of the drum. So there is no barrier between the drum and your floors basically. Then one day we had a flood. As we watched the cycle run, we noticed that when the water was filling into the bleach and fabric softener compartments it was coming in at such a high rate, it was spilling over the sides down to the floor. So we went to the internet and found a few complaints about this, but no answers. Thankfully we found one guy who had the exact same problem and even had pictures that matched ours. Luckily a real appliance tech answered him and he couldnt even figure it out but took a guess at what I might be: the water inlet valve. But that was just a guess. So we called around to find the part and talked with a few sales persons. One was so nice to even ask a technician standing in line. And he said that there was no way this could be it. But then we decided to take a gamble. We also noticed that both compartments were filling up at the same time, but the bleach should fill during the wash cycle and the fabric softener during the rinse cycle. So it was either the $104 water inlet valve. Or the $200+ circuit board. These are my options after already spending $900+.. So we went with the valve and thank goodness it worked!!!! It is so disappointing that after a short time, this washer broke and cause more damage to my floors. It is an awful design. I bought myself the nicest front loaders for my first house. When that broke 7 years later, I bought this washer because I liked the no agitator design without the smell of a front loader. Now when this one breaks again, Im not buying another HE machine. The majority of people I talked with today said that these HE machines are breaking down faster and faster as the get better and better. I am so beyond disappointed, angry and in shock that this washer failed in less than a year and a half time. My hope is that this review will give the answers we couldnt find without paying an arm and a leg. Is this what passes for quality these days???

I have a Bravos washer model # mvwb45owqo and matching dryer. The price for the pair was $1347.00 plus tax. The washer and dryer were bought Jan 14 2010. 10-10-13 the pump went bad and was replaced. I paid $ 221.00 to have it replaced. 10-31-2013 I was washing a load of cloths and it was very noisy. I call the local dealer and they come out and said that it needs a drive shaft tub part #w10193886. I would be about $300.00 to replace the part. Also they charge $75.00 for a service call. I called Maytag and talked to Ashley (**) from customer service and she said they could not give me any help that the washer was too old. I might also add that my last washer was 3 years old and the motor needed to be replaced. It was also a Maytag. I always thought if you paid more money for quality it was worth it. I am sorry I did not buy a cheap machine from Sears or somewhere else. It would of been 1/2 of the cost and I could of replaced it after 3 years or so if necessary and still been money ahead. We also have 4 rental homes that have all Maytag in it. I will be holding my breath that they are not junk also. I will tell everyone I know not to buy Maytag and I will never own anything that has the Maytag name on it again.

After having a Maytag washer/dryer set that lasted 20 years, I decided to go with Maytag again. Big mistake! Centennial Dryer has already broke down and the parts, before the overcharged shipping, was over $100. I wish I had done some research. Maytag is no longer Maytag, it was purchased by Whirlpool. Hence the lack of quality. Not only that, I dislike doing business with heartless companies that just close shop & let loyal employees go while paying upper management fat severance pay. Then Whirlpool changed the vested lifetime benefits of the Maytag retirees. Will not buy another Maytag appliance and will never purchase a Whirlpool product.

I just want to give an update on my frustration with Maytag dishwasher I wrote about on July 16. In the end, I found a DIY solution and fixed it. I wrote an instructables here: **. Not recommended if you dont feel comfortable repairing things. However, the diagnostic test at least can give you some clue whether its the control panel or control board is at fault before replacing both. Thanks.

I have had my stove since 2004. A problem I have had was when I asked it to clean the ovens, it quit working all together. A service person was called. Also sometimes when I turn on one burner, another one will turn on instead. Yesterday I turned on a burner to low, and it did not turn on at all.

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

Have had this problem since week 2 of ownership. Even on the lowest setting, food in the fridge section is freezing and Im having to throw out fresh produce weekly. Called Whirlpool service since under warranty. The very nice service man replaced the thermostat. Only a little bit better as the temps do not range quite as extreme - only 25-46 now! I am now waiting once more for a service appointment, at least 10 days. Plus in Massachusetts they will only give you a 8-5 service window. They give a robocall the night before and you are given a 8-12 or a 1-4 time for your appointment. I also have had trouble with the meat drawer falling out of the track because the upper shelf bows with the weight of a normal amount of stuff. Now the bracket has cracked and the meat drawer no longer stays on the track when it pulled out partially (such as when you need to reach in and get something). Same thing happens with the lower drawer on the right side although the bracket hasnt cracked.

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

Replaced an old Glenwood gas stove with this Consumer reports top rated Maytag. The boiler doesn’t work as well as we’d like, but after more than 20 years, no major issues. My wife & I both cook, & as with most things, I’m happier with it than she is.

In 2006, my wife and I purchased a new Maytag refrigerator, the model type with the freezer in a drawer near the floor and the drawer is under the main door of the fridge. The thing has a sealed system and has a freon leak which makes it nearly impossible and not financially prudent to try to fix. Two repairmen were out and I spent $200 for them to tell me the same bad news. Its unbelievable that this junk wouldnt even last ten years. What is this, Russia? Ive heard some of their awful appliance experience stories and now this can join them. The reliable Maytag repairman who never has anything to - you know the one. He is probably dead. Hes not really the one to blame here though, it is the reliability of Maytag that is dead and will remain so for as long as this company is alive. Dont ever trust or buy Maytag if you care about making your investment in new appliances last! Dont do it, people!

I have had this refrigerator only 6 weeks. The freezer works but the refrigerator does not cool properly. I went back to Home Depot - Baltimore MD and told them I have lost 3-1 gallons of milk for it spoiled. I am right now putting a 4th gallon in and out of the freezer trying to keep it. A serviceman was to my house the other day and stated this brand new Maytag refrigerator only had in my home 6 weeks needs a new board and a flapper that opens up in freezer that sends cold air to refrigerator. Parts are on order. Home Depot would not trade a Maytag refrigerator that worked well and take this lemon back. I am stuck with a lemon I only bought 6 weeks ago.

Duck bill valve for defrost water from freezer malfunctions, water flows into freezer freezes, then eventually overflows onto floor. Huge problem for folks with wood floors. Also a slip/fall danger especially for the elderly. When the repair line is contacted, they deny the problem and say you are the only one. But if you do your research, you find there are hundreds of complaints and in November 2013 they issue a service bulletin, but its internal, not meant for consumers to find out. So if you have this problem, go to the Consumer Product Safety Commission and fill out a complaint. Maybe then something may come of it.

Control panel broken for a second time in 23 months: I purchased a Maytag dishwasher less than 2 years ago at Home Depot. 11 months later, the control panel went out. Specifically, the start/cancel buttons stopped working. A service tech called me under warranty; the control panel was shipped to me, and the tech fixed it. He also told me that they had had numerous problems with the control panels.13 months later, the control panel went out; specifically, the start/cancel buttons stopped working (sounds familiar). I can get nothing from Maytag, except a demand for service fees or sales pitches for extended warranties (at a price that was half of what the dishwasher cost new). They also offered me the free part as long as I pay the service call fees. I told them to just to ship me the part and that Id do it myself. Nope. I must pay the repairman. Now, theyll ship me the part if I pay for it, but they wont ship me the free part. It only comes with a service call.Maytag also told me that there were no reports of problems with the start/cancel button, an obvious lie with a quick internet search. The customer service rep sounded like she knew I was getting treated badly and kept using the word policy. Her supervisor was much more cocky and made sure I knew that I wasnt getting anything from her company.They make horrible products, attach what once was a good name, provide zero customer service, and lie to your customers. Great business practices. I will never purchase a Maytag product again.

Got the dryer free when we moved into our townhouse. We had been doing 2-3 loads a day for almost 8 years. The dryer was old when we got it. No complaints. Just wish there was some way to fix it. But mechanic said, No way. Almost a valued member of the family. Say 2 loads a day, 7 days a week, 52 days a year. This is a lot of loads. Remarkable. New machines cant do that today says our mechanic, they are not built to be fixed. Now, when broke, replace, don t fix.

We bought this from our local big box retailer paying $433.87 after installation, the oven, haul away and home delivery. Two years and 3 months later its a boat anchor. Display is cold and dark after stating we needed to open and close the door before it would heat. We did but it kept displaying the same message. Unplugged it, turned circuit off per Maytag customer service line, still nothing. It is no longer made and you cant get parts. It is useless. The 10 year warranty just covers the magnet and the cavity.

I purchased a Maytag Dishwasher in April of 2011 - Ive had four control panels in that time and the panel gone again - in fact, one panel came out of the box nonfunctional (I counted that one as it was installed although the tech removed it when it quickly became apparently that it wasnt working). Ive got a complaint in to Maytag but I have low expectations as to a satisfactory conclusion. What Id like is for Maytag to buy this lemon back from me for around $400 - I paid nearly $600 (including installation). Again, I doubt this will happen. From my research online it appears that the control panel issue is a latent defect which Maytag knows about but either wont or cant figure out how to deal with it or correct it. I have a scan of the receipt which Ill see if I can upload later. I know about one class action lawsuit for CA residents. I wonder if its been expanded.

Maytag Neptune was purchased over 15 years ago to replace GE, which we purchased when children were little. I wanted a step up in quality. I remember paying around $499 for this unit. This is an analog unit. The intellidry feature has been a real asset, protecting our clothes from over drying. We have had this machine for nearly 20 years. It has been real reliable, sometimes drying 20 loads a week. Large capacity, but has to fit down a narrow and twisting stairway. Must be energy efficient, have good reviews and decent price. We always look for sales or buying incentives. Brand is secondary to quality. Knowledge of an appliances historical reputation is important. I would look at reviews, especially concerning cost of repair. I would attempt to get a hands-on view, before purchase from a reputable supplier at the best price. My dryer has only required one major repair in the time Ive had it. A few years ago we replaced the motor and blower, and I have personally replaced the drum support rollers twice. I hesitate to replace this machine, because the analog controls have proved very reliable.

My washer (Performance Series 4000) needed new bearings about 6 months after purchase. By the time the parts came in and after the A&E repairman rescheduled because he didnt know how to replace them, another two months had passed. Now, a year later and with no more warranty, the bearing needs replacing again! This washer is only 1 year 8 months old! The first repair cost well over $1,500 but was covered under warranty. There are hundreds of other people with Maytag washers having the same issues! Maytag is well aware of the defect and refuses to take responsibility. I would like to file a class action lawsuit against Maytag. Im in Tennessee. Please contact me. Thank you.

I bought a top of the line Maytag commercial washer. We had a number of service calls replacing parts, gear box etc. Then, they finally replaced the machine and all the same issues happened again. They will not take back their machine or refund me my almost $1K paid. The washer squeals when it starts washing and clunks all while agitating - I can hear it upstairs. After yet another service call (#11 now and no salary replacement for me) the result is that Maytag says when the temp in the house is 67 or lower, the parts in their machine expand and contract and will make noise. No fix, no refund oh, and no one you can contact by email in Canada to help. Moral of the story, dont buy Maytag.

This product is not worth the money or irritation. It does not wash your clothes well and now mine wont spin. I have to completely unplug the machine and start it up to drain and spin. It takes 1 1/2 to wash one load of clothes. Its supposed to be energy efficient. Im pretty sure its not! I waste more time and electric doing a load of clothes than it takes to dry a load of clothes. Im dumping this thing for a real washer, one that works. I do not recommend this washing machine. I purchased the Bravo at Lowes.

Less than 1 year ago, my washing machine that my husband bought me was a Maytag Mod #MVWC200XW0. It went. The repairman came and had to put in a brand new capacitor and less than 3 months later, there are two things that are wrong with the washer and I cant use it again. I have to go to the laundromat and take clothes elsewhere to get them done. I took out an extended service agreement in January. Maytag deducted $21.18 from my checking account and they never sent me an invoice for the balance of $42.36. I kept calling and trying to get an invoice. Then on June 25th, I received a letter in the mail that they cancelled my service agreement. I guess this was cancelled in May and they sent me a letter a month later. Now, the repairman was there last night and they could not fix it without us paying upfront and the extended service plan said they didnt even know if we would get reimbursed for any of the parts. This is very poor for a washer that is just a little over a year old. As far as I am concerned, this washer is junk and needs to be junked. My husband got a lemon. I am not putting this amount of money in something that every 3 months has something going wrong with it. I would appreciate a phone call back or something that could be done. Thank you.

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

Maytag model #MDB6949SC, purchased Feb 22, 2015. In early May plastic parts from the top rack wheel assembly broke. Assembly unit replaced at no cost through the 1 year warranty. (cost = time and effort to arrange replacement with repair person). Same parts broke again in November - replaced at no cost again under warranty. Warranty expires in two months. If past performance indicates future performance, this part will need replacing twice a year at ~$140 per visit or $280 per year. Not a good thing. Called Whirlpool and with several calls and emails. They offered an extension of a year on the warranty. I think using plastic for this wheel assembly unit is a design flaw. Would not recommend this dishwasher.

We bought our front load washer and dryer about 5 years ago and have had no problems with either. We also purchased a Maytag French door refrigerator 2 months ago to replace our Sears Elite brand when its compressor went out after 27 months (Ill never buy another Sears appliance).

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

My Neptune washing machine does not drain or spin. It keeps going unbalanced. I am told that I used the wrong detergent. The machine takes a whole day to wash a small load of clothes and then never finishes. Clothes and towels are constantly being ripped and torn. This Maytag product is inferior and we have paid a lot of money for this product that does not work. Repairs to this product are not advised, we have been told that we just need to buy a new one again. This is poor service and poor advice.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

I really love my front loader and it has no agitator to rip pockets and tear off buttons. The tub is very large and I can wash king quilts. I do miss being able to fill the tub and put in additives and then add the clothes to soak.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

I purchased the subject Maytag washer (MHWE201YW-3.5 CU FT WHT FRNT LD WSHR) from Home Depot in December of 2012. I got exactly 1 year of use and then the washer stopped working. I called the Home Depot repair person who came and repaired the unit. The repair lasted two weeks and the washer stopped working again. Because the unit was no longer under its 1-yr warranty the Home Depot repair person was not available for repair. Another independent Maytag repair person came and evaluated to problem. He said the computer which is located on the motor was no good and to the tune of over $400.00 (parts and labor) a new motor was purchased and installed. It lasted two months and it quit working again. After several months I was finally able to contact the original Home Depot repair person for one visit. He said he would check the code message and get back to me. I never heard from him again. I have been taking my laundry to the laundromat ever since and it is getting expensive. I dont want to spend another $400 on this machine as it will only break again. What do you recommend?

I bought Bravos xl. I hate it! Everything about it. It does not get my clothes clean and it ties load in knots therefore being off balance constantly.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

We purchased our home five years ago. We bought a new Maytag oven and fridge/freezer. Within one year, the oven control went out. Then a few months later, the heating element went out. Within two years, our fridge/freezer went out. I purchased Maytag products because of the commercial where the Maytag repairman is doing nothing. I will never purchase a Maytag product again.

I had a Kenmore that lasted 20 years. This didnt last 5. Paid a lot of money for a disposable washer. Red in color on top of that. When I bought I did my research and had good reviews. Dont buy any new technology -- not enough data. This a POS. No more Maytag for me. Spoke to a repairman -- water leaking from the bottom and bearings are out -- was told it was a bad design. 951.00 -- energy guide said the annual cost to operate was 30.00 a year -- my calculation is 30.00 + 190.00 = 220.00. What a ripoff. Never a Maytag for me again. I only really needed a dryer but thought that I would update and just get a matching set for my women. Now we will be going back to an unmatched set. What a terrible purchase. Review says 5 star -- that is for the Consumer Affairs -- not the washer.

Bought machine 03/23/15 exactly 2 yrs ago & machine will not work. It looks like the electric panel and which there are a lot of complaints about the panel, and the lid. It seems as its about the extended warranty now. The quality that Maytag advertises is lies. You buy the product and you have no choice but to purchase a warranty on your machine. Simple is better when it last 20 yrs over 2 yrs on a fancy machine. First electric panel machine washer with a horrible experience. It will cost 98 just to look at, that is not including parts and labor. Its 339.15 for a year warranty which equals over 300 per year for 3 years. Overpriced in all ways. Worse choice ever.

As all the other reviews day 1 Dryer had no heat, washer unbalanced and knotting all the clothes. Sent out new dryer after trying to fix to no avail. One month after new dryer, normal cycle continues to run and not turn off. Repairs again - new computer board. Now washer is winding high pitch noise level - repair new bearings. Thank goodness for warranty. But washer and dryer act up again. I purchased extended warranty. Washer tub needed replacing because transmission went out, dryer again control panel problems. Last night the dryer started on FIRE. I’m sure because the control panel normal was not working again after it was replaced less than 2 yrs ago. Total time owned 6 miserable years. Going back to basics, ugh....

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

After the 4th service call Maytag wanted a 2nd company to look at it. So on July 27th A&E out of Bristol, PA came out. He checked it out and said its not serviceable because theres a leak somewhere in the casing. Had to call KYW 3, On Your Side, they helped me get some progress. Jacqueline from corporate called and said they would replace it. It started on July 3 and now August 13 and still no fridge. Had my Maytag washer fixed, small problem. Parts came in a box marked Whirlpool for a Maytag washer from a Sears Warehouse. Plus the mechanic said my Maytag refrigerator is made by Amana. Buy American?

If I could give less than one star I would. I purchased a Maytag range in September 2021, 33 days later the oven went out!! I have been fighting trying to get it repaired for months!!! The parts are not in, the parts have been shipped, oops we forgot to ship the parts, the technician is on vacation. You name it, I have heard it. After the phone call today, it looks like I will still be without a range at Christmas!! This is totally unacceptable. I purchased a Maytag because I assumed it was a good brand! Do yourself a favor... Never buy a Maytag or Whirlpool Appliance. Its not worth it. For the range to only work for 32 days is just plain Wrong....

Just a year after purchase, this Maytag Bravos Washer stopped spinning the clothes. It never washed worth a damn anyway. I paid extra money for a quality product from a known brand name and I was taken to the cleaners. Never buy a Maytag product unless you want to replace it in a year.

Purchased my Bravos June 2012. This is a horrible washer. It does not clean. It leaves a detergent scum line on clothing. My work clothes are visibly soiled and sometimes come out in a tangled mess. Maytag ignored a first complaint from my wife. I complained again today. Regardless what Maytag does, I will purchase another brand after research. We bought on Maytag’s reputation.

Does a good job. The only thing it has problems with is frying pans, but no dishwasher can do those. 4 cycles, option to turn off heated dry. Standard size. Fit the cabinet perfectly. Just a plain white front, which is fine, but it did not get 5 stars because the white plastic control panel seems to catch and show dirt easily compared to the white painted metal door. Ive had this machine 15 years and the only repair needed was replacement of one of the rollers on the lower dish rack.

The washer is making loud noises. I had a repairman out and he said the transmission was shot. This washer is only 7.5 years old and the set I had before lasted 19 years. It also was a Maytag. My mother, sisters and aunts have always stood by Maytags and I am disappointed that this washer being 7.5 years old is shot. The dryer to the set is working great!

Purchased a Maytag dishwasher 1 1/2 years ago and the panel went out. I paid $550.00 for this item, wanted to get a nicer one hoping it would last. Of course they only have a year guarantee for parts and Labor. Will not buy another Maytag appliance again!!!

Maytag Centennial Impeller HE Washing Machine - The seller left this piece of junk for us. I wondered why because it appeared brand new. After the first washing I knew why. I sure regretted leaving my old set behind. This washing machine wont let you add the amount of water you need. I had to add buckets of water and hope it didnt just empty it out because the sensor controls everything. Twice it just emptied it after I closed the lid and it locked. There is an impeller instead of an agitator. It moves slightly but not enough to move the clothes. To top it off the spin cycle tears into the clothing and twists and wrings it so hard everything is wrinkled with soap residue remaining even on delicate. Each load takes over an hour and the clothes arent even clean. It went to the dump after 4 washes. I went on Craigslist and purchased a used Kenmore and am in heaven. No lock, an agitator, 3 water levels, clean clothing, you can open it and add the missing sock, no sensor controlling how you want to do laundry and no more buckets. Dont buy a Maytag. Look at all of the reviews. They arent exaggerating, they are really that bad. Thank you.

March 7th. My refrigerator ice door started flapping and the lights flickering. The next day it quit working. I called Maytag. They said they would have someone come fix it the next week. The repair service people called me back the same day to tell me that the part I needed has been on back order for 2 months. I called Maytag back. They told me to wait a week they put out an all alert for the part. I called back in a week. Now they tell me its 2 months. This is ridiculous and a huge inconvenience. I will not buy anything again from Maytag. $2,800.00 refrigerator should last a minimum of 20 years. This should be a recall. Thousands of people are having this problem.

To begin with, the Bravos 300 washer was bought because we owned a Maytag previously and it was with us for 25 years. It was still running when we gave it away and the only problem was a small oil leak starting at the drive. The new washer has no agitator, just the new style flat thing at the bottom of the tub. You cannot wash a set of fitted sheets without it turning into a tangled mess. The washer quit working after about 5 years and all indications pointed to the control. The control would reset after unplugging, but would freeze immediately when you tried to enter a command. We live in an isolated place and it is not feasible to fly in a service person. I ordered a new control, but there was no change in function. After several hours of detective work, it turns out that the mickey mouse plug for the electrical connection at the pump had broken inside. Because the pump would not work, the whole control would freeze. We will never buy another Maytag.

Maytag washer MHW5500FW had service just a month after purchase and still a year later the washer has problems spinning using direct drive. Even a few towels are soaked when cycle is done or errors out and must be restarted. Most of the time the washer has to be cycled on spin to remove water from soaked items, not just a simple bath rug, towels, bed sheets. Almost anything has a problem spinning. Had to purchase another year of service coverage as I dont trust the washer will last. Soap dispenser needs to be diluted despite using correct soap, per service tech advice which triggers sensors to shut down. Machine looks good but not ergonomically designed without the stand as you can easily lean over the washer and turn on and off accidentally. Same goes for the matching dryer, also can easily set off the on pause and on/off button. Dryer works great other than that.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

2 Year old washer. First the actuator was replaced. A 150.00 charge. Two months later the pump is shot. Another 200,00 to replace the pump. This is worst piece of ** washer I have owned. I would not recommend to anyone. Stay away. I would give it 0 stars if I could.

I purchased this dishwasher about eight years ago, and I love the performance and the stainless steel interior. I never have a problem getting my dishes clean. This product definitely lives up to its reputation. Going forward, I would definitely buy the same brand if it became necessary.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

This unit is only 4 months old. It freezes everything, vegetables, eggs, etc. It took more than 3 weeks for the technician to show up at my door!! Performed a service modification according to the manufacturer specs. This did not work!! Call again to have a it fix. He show up almost 2 weeks later. This time he replaced a part, worked fine for almost 2 weeks. Now I am having the same problem. I had it with this Maytag piece of junk!! I will never buy anything from Maytag again!! PLEASE DONT WASTE YOUR HARD EARNED MONEY... IN MAYTAG PRODUCTS!