I purchased a Maytag Bravo Washer and Dryer about 2 years ago; dissatisfied with the products. Washer continues to smell. I clean it all the time with the Affresh tablets. Usually, I have to use 2 bags just to get it not to smell for at least 2 weeks. Now, the glass front dryer is rusting out around the window.

It is quiet and cleans well but thats where it ends. We have had it a little over a year now, after just a few months it started leaking, fixed under warranty. Now one of the upper rack tracks is broken, it was held together with three very flimsy welds, hopefully will be getting it fixed soon. We are going to wait and see what other kind of repair it will need, I think we would have been better off to just buy a cheap dishwasher!

Model #MDB8959SAS1 MAYTAG Dishwasher - purchased in 2014 at Home Depot. First we had to replace the rack adjuster, and after that another part broke. Finally, the electrical control board totally melted and smelled up the house. Fortunately our breaker switch worked and it didnt cause a fire. But Ive read other reviews of this happening with Maytag dishwashers where there was a fire. It now resides at the landfill.

We (husband and wife only - no kids) had our Maytag washer for 4.5 years and around year 3, the control panel would need to be reset by unplugging it and plugging it back in. That alone was an inconvenience. This time, the Control Loc light is lit and will not go out despite using all troubleshooting suggestions listed in the guide so the washer is not usable. 10 year warranty covers the drum. I say that is like getting a warranty on tires and when one goes flat, you are told it only covers the hubcap. I can only rate the unit as garbage. Model is 5500, front load. So much for Made in the USA.

This is undoubtedly the worst washer I have ever owned or used! I have never before felt compelled to write a review on a product, but I wanted to make other buyers aware. There is not enough water to clean the clothes - the water level doesnt even cover the top of the clothes, so the top of the clothes are dry as they are agitating! After drying (dryer doesnt dry either) the clothes do not smell fresh or clean. Ive put up with it for 3 years and am disgusted every time I use it. Im just about ready to buy another set.

Every time I do a load of wash, it comes out looking like I slept in it. It is so wrinkled you cant even iron it all out. If the load gets off balance, you have to wring it out by hand because you cant get it to spin again. I did a load of flannel sheets and it went off balance, wringing sheets out by hand is enough to make a person want to send the machine back and get an old-fashioned wringer washer. I hate this machine without an agitator. I have always used a Maytag washer, but I would not recommend this to anyone.

I had this microwave less than a year. The control panel went out and Maytag fixed it. Now a year and a half later, the same thing happened. This product was almost $400 at the time we purchased it. I have had better luck with $40 microwaves.

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

After having had Maytag Highlander washer and dryer for 28 years in our early married life, and continuing to think that Maytag was a quality product, we purchased the Neptune front load washer MAH6700AWW. Let me tell you this IS NOT your mothers washer, nor is this Maytag a quality product. First it was necessary to install water pipe shock arrestors because of the water valve on washer causing shock in the waterline when it closed. The automatic Softener/detergent dispenser didnt work from day one.Coins and etc. constantly kept getting under flippers and couldnt be easily removed. I found that it was impossible to remove the plastic flipper without breaking a plastic mounting tab. On my first call to customer the Maytag Customer Loyalty Team, aka Customer Service (CS), I was told that the plastic flippers were not available as a separate part, and that the entire tub assembly with plastic flippers would need to be replaced. WHAT???????? THATS LUDICROUS. After temporarily securing the broken flipper to the tub, I thought Id call again about a week later to see if the previous answer was correct. On this call, the customer service lady (whose name I have), said the flippers are available and that she would send two at no charge. A few days later two flippers arrived, but were not the correct ones. I then decided to drill two holes in the tub and remounted the broken flipper with two stainless screws as a permanent solution.Two pumps needed to be replaced. One was replaced under warranty and one by myself. The one replaced by me was damaged by a coin that made its way from the tub to the pump. Other washer manufacturers provide a means of trapping such objects before they get to the pump. The wash cycle stopped unexpectedly numerous times without reason, after which the code 5d was displayed. I called Maytag Customer service. The representative didnt know what 5d code meant. Her suggestion was to call a service man. Again, I called later to ask and was told 5d meant excessive suds which wasnt the cause. Might this have been a control problem?There were three incidents of water discharging onto the floor from under the washer over the last two months, which caused water to cover an area of approximately 5 by 12 resulting in extensive cleanup in addition to damage to stored items. Since these occurrences were weeks apart and unpredictable, I knew the problem would be difficult, if not impossible, to diagnose, even by a serviceman. I concluded that it was probably a problem with the control; either filling too long or not emptying the tub before refilling for the next cycle. Thats when I decided to send this troublesome Maytag piece of junk to the landfill.

Maytag Bravo washer and dryer purchased April 2011. Dryer works fine and am pleased with results. Washer does not clean simple dirt and stains off clothing. Washer never fills to a water level that covers all the clothing. Some clothing never gets submerged, thus simple stains never get water contact throughout the cycle. I now spend more money purchasing spray stain removers and using the heavy duty cycles and extra rinses, would have been better off getting a Kenmore with an agitator. The concept does not work.

I purchase the Maytag Bravos washer & dryer set 3 1/2 years ago brand new. I figured being a Maytag it would last for a long time but nope I was wrong??? I will never buy another Maytag product as long as I live and I will tell all my friends and family not to purchase a Maytag product also!

I had no issues with my washer. The best thing I ever did was stop using Sabrina softener in it and made the switch to vinegar. The worst thing I ever did was think that paying $900+ for a nice washer would get me more than a year! What a joke! I started noticing small leaks when my hardwood floors started lifting and once my husband looked into this, we realized there is no seal around the top of the drum. So there is no barrier between the drum and your floors basically. Then one day we had a flood. As we watched the cycle run, we noticed that when the water was filling into the bleach and fabric softener compartments it was coming in at such a high rate, it was spilling over the sides down to the floor. So we went to the internet and found a few complaints about this, but no answers. Thankfully we found one guy who had the exact same problem and even had pictures that matched ours. Luckily a real appliance tech answered him and he couldnt even figure it out but took a guess at what I might be: the water inlet valve. But that was just a guess. So we called around to find the part and talked with a few sales persons. One was so nice to even ask a technician standing in line. And he said that there was no way this could be it. But then we decided to take a gamble. We also noticed that both compartments were filling up at the same time, but the bleach should fill during the wash cycle and the fabric softener during the rinse cycle. So it was either the $104 water inlet valve. Or the $200+ circuit board. These are my options after already spending $900+.. So we went with the valve and thank goodness it worked!!!! It is so disappointing that after a short time, this washer broke and cause more damage to my floors. It is an awful design. I bought myself the nicest front loaders for my first house. When that broke 7 years later, I bought this washer because I liked the no agitator design without the smell of a front loader. Now when this one breaks again, Im not buying another HE machine. The majority of people I talked with today said that these HE machines are breaking down faster and faster as the get better and better. I am so beyond disappointed, angry and in shock that this washer failed in less than a year and a half time. My hope is that this review will give the answers we couldnt find without paying an arm and a leg. Is this what passes for quality these days???

I purchased this dishwasher about eight years ago, and I love the performance and the stainless steel interior. I never have a problem getting my dishes clean. This product definitely lives up to its reputation. Going forward, I would definitely buy the same brand if it became necessary.

Before today I was happy with my washer. Well yesterday I heard this loud noise. It turns out to be the gear case on my washer. To my surprise the repairman told me that it would cost between $450 and $500 to replace. I called Maytag to check on the 10 years warranty and was told that it would cover the basket and the motor but not the gear case. That is very stupid because without the gear case the washer will not work. This gear case help the sensor work, the basket work. DO NOT BUY ANY A MAYTAG PRODUCT. They do not stand by their product. I have had my washer for 2 years and 10 months. Before this the last washer I purchase was a Lady Kenmore through Sears. I had that washer and dryer for 25 years.

Does not clean laundry, leaves dry untouched spots, all my clothes look unwashed & the rinse is terrible, leaves dirt on clothes due to little water in cycle. Im a senior on fixed income. I cant buy another machine.. I called Maytag within a couple of weeks of using washer. They told me We have No guarantee for Customer Satisfaction. This is a complete scam on their part. If I could of afforded a Lawyer I would of taken them to court. They knew what they were selling & somehow got away with it. Give the people what they pay for, not the Bravos piece of Junk. Can only wash on 1 cycle to get wet wash. But paid for other useless cycles. Who made this machine & who allowed it to pass to the unfortunate Consumers. If anyone can help getting Payback from Maytag, Please let us know... Better business Bureau should get after them.

I have a Maytag Neptune washing machine which had a mold problem on the rubber grommet. I have been trying to call Maytag to no avail. I researched and saw there was a class action suit for this very problem and I was never informed. The washer may pose a health hazard and I would like Maytag to do something about it.

We purchased a Maytag Bravo washing machine and dryer from Home Depot so needless to say, it was not an inexpensive purchase. I absolutely will NEVER purchase another Maytag ANYTHING! The washer will not spin and when it does, it sounds like it is coming through the washroom doors. The heating element has had to be replaced in the dryer and has always had a sour smell inside. I have nothing nice to say about these products and would absolutely NOT recommend them to even my worst enemy!

Our Maytag refrigerator was about a year old when we noticed rust on the edge of the stainless steel doors. I called Maytag and they were nice enough to replace the doors even though the warranty had expired by their standards. Keep in mind, the warranty starts when you purchase the product, not when you install it. We ordered our appliances from Lowes well in advance of our kitchen remodel so we would have them when we needed them. The time our appliances sat in Lowes warehouse used up two months of our warranty.Now, the new stainless steel doors are rusting and they are refusing to do any thing about it. Should stainless steel rust? Maytag doesnt seem to care whether their product performs the way they should. Its all about the warranty. Once the warranty lapses, they could care less whether their product blows up. Thats the customers problem. Whatever happened to building a quality product that lasted and customers bought for generations? Obviously, thats a thing of the past.My goal in writing this is to make consumers aware of appliance warranties. When I spoke to Lucas, a Maytag customer service supervisor, he informed me their products offered no warranty on the finish of the product. So, according to Lucas, the finish on your brand new Maytag appliance could flake off like dandruff and its your problem regardless whether its a manufacturing defect or not. Remember, buyer beware!

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

I have the Maytag Bravos washer and dryer. The machine has broken several times every year, and every year, Maytag makes me feel like it is my fault. They built a machine, and they do not stand behind it. And I cannot get a local machinist to work on it. I have asked Maytag to replace it from the start, and they refused, telling me its out of warranty. The only thing out of warranty is the frame--all parts are new. Here is the history:On 1/04/2008, I purchased it from Home Depot, and it cost $815. Then in 4/2009, there was an F51 code, and Maytag replaced the mother board after long hold times and much pleading to help me. They said they could do nothing, because it was out of warranty. It took manager to manager to manager to get the agreement to extend the warranty. (I then found that this was a regular Maytag issue.)From 9/2010 to 10/2010, an ld code occurred. The approved Maytag scheduled service had to come out 4 different times to attempt to fix the issue. One time, they said it was broken wires for the drain pump. The next, it was off balance; and the next, it was a sensor. Then the next time, they replaced the mother board again, and again after much argument that the part was less than a year old. Each time, they get more and more difficult to deal with and made me feel more and more like I am asking them for something unreasonable. The service guys said the washer was like new.... All new parts and I would never have a problem again. It cost $80 after argument, and Maytag covered the parts.Last 2/2011, problems include a fast spin, ld code, and off balance; and it stopped working. It needed new suspension rods which cost $250. Maytag paid nothing. Then in 8/2011, ld code started again, and I would have to turn off to drain and then restart to spin. Maytag called in a service call, and they never showed up. Every time, they said they read over my file and that theres nothing they can do to help me. And no one else for me to speak to.In 10/2011, the ld code came on permanently. The Maytag call I made this time again said there was nothing they could do to help me.I am so frustrated; I dont know what to do next. I threw away an older set working washer and dryer, thinking I made a great decision to upgrade to this new set. Now my family of 5 cannot wash our clothes. No one will work on the washers locally, and Maytag treats me like Im complaining for nothing and I should just spend endless dollars to fix this machine. And Im at a loss. I had to get a part for the dryer the other day, and the parts store person told me that this washer is one of Maytags mistakes. if that is so, why wont they help me?

Called about our upteenth issue with our Maytag microwave. Was told the part was covered but we would have to pay for service. The last tech told us how to wiggle the part to make it work. Paid a fortune and it broke again. They do not care about customers!!

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

Purchased MAYTAG DISHWASHER MDB7809awm in 2011 for $719. In 06/2013 the far right 3 buttons stopped working. I contacted Maytag to see if there was an issue with this and they reported that there was not. I had the part replaced in 06/2013 at $280. It cost me 1/3 of the purchase price of the dishwasher. The repairman said that he sees this a lot with Maytag control panel issues.On 08/02/14 the same exact issue occurred. I contacted Maytag online on 08/02/14 and didnt hear back until 8/13/14 to say that there was no known issue and all they could do was recommend a repairman. I also called before I heard back via email and they said the same exact thing, there is no known issue and we can do is recommend a repairman. I am not interested in repairing. Been there, done that. Not doing it again. I researched the issue of the 3 far right buttons not working and there are several forums and discussion topics out there. I find it hard to believe that MAYTAG is not aware of this issue. If you GOOGLE the model you will see the same issue. Not only is the MAYTAG product poor, but they have the worst customer service I have ever seen.

I have had my Maytag set for shy of 2 full years, of actual usage time, that is. My dryer seems to be functioning normally, minus an occasional lengthy cycle time, even after the clothes are dry. The washer however, is sitting in my garage now. F51 error code, which online told me the rotary position sensor was the issue. Yes, I was told by an A&E repairman, who was at the house for an unrelated repair, that it was the bearing that was bad. When he showed me what I was looking for, there was the bearing laying in the clear plastic housing, in the underside of the washer. Its going to cost around $350.00 to get the part, if it can be found, and the service call. No, not really worth wasting more money on it. I am very unsatisfied with this unit. With 4 kids and 2 adults at home, I expected much more from the Maytag name.

Maytag Bravos XL - This is the worst product I have ever owned! I purchased a Maytag because when my husband and I were married 29 years ago we bought a Maytag washer and dryer and still using the dryer. However we lost the washer and had to replace it. Worst mistake ever!!! Within a year a circuit board went out (they replaced but I was advised I needed an extended warranty which I do have) and was told by the technician that this model was junk! I called Maytag and expressed my great disappointment and all I was told is we document customers input. I then ask ok so what are you going to do about it? And I did not get a response. I asked for a different model but was declined. As you can see it is rusting at only a 1.5 years old and tearing up my clothes. It destroyed a doily that belonged to my late mother. Maytag used to have integrity in their product but not anymore. Not only all of these issues but I have to wash clothes twice and they still are not clean. Plus they have a dirt film on them and yes I used THE detergent!!

I had one set of Maytag washer and dryer and I loved it. I bought another set and hate it. The washer smells and has been fixed a couple of times and the dryer is bad. I had to have a drum replaced because of one of the bars inside. I paid for the insurance but the bar was considered cosmetic. It has fallen off again after about 2 years and Im sick of it. I will never buy another Maytag again. Repairman, of course, had to order the drum and then I had to take another day off work to be here when it was delivered and one more to wait for him to come. I am so unhappy with this brand - never again.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

We purchased our Maytag gas range in 2015. Within 6 months we noticed the clear coat and paint was defective, we called Sears, they allowed us another range top and replaced it but told us our warranty was up in a month and they would not replace another. The stove always looks dirty because the clear coat and paint have bubbled up and it is clearly a 100% manufacturing defect that should be recalled.

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

Just like all the other reviews, the control panel on our 3-year-old dishwasher stopped working. The obvious defect of the product and lack of customer support is unreal. We ended up replacing the Maytag with a Frigidaire. Hopefully it lasts more than three years.

I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

I purchased this range from a Maytag outlet in Nov. 2006. No problems with it until Nov 2015. The oven igniter failed. This was serviced locally and replaced in an efficient manner by the local service tech. All is good until 2 days later when I decided it is time for an oven cleaning cycle. I set the cycle for Medium Soil (3hrs). After the conclusion of the clean cycle, the oven (bake) would not work. Called Maytag service, the service tech replaced burned up oven wiring as well as the igniter again. However, the cleaning cycle had taken out the gas safety valve control as well. I am now told there is no replacement oven gas safety valve unit available anywhere. I even called Maytags 1-800 number and searched online only to find the part on backorder and not available.I find this particularly frustrating in light that I spent over $1200 on a Maytag product I thought would bring way more than 9 years of service before it is deemed unrepairable. The average gas range lifetime is 18 years. In my opinion, not a good return for the investment. Its a shame because the rest of the range works and looks fine, which is now destined for the dump. I am replacing the Maytag with a $550. Frigidaire with manual cleaning. Will never buy another Maytag appliance or a self cleaning oven again. If the self cleaning feature has the potential to fry the controls, why would they offer such a feature, or why couldnt they warn one of the potential failure.

Had the new set for over a month now and are very impressed. If you actually know how to do laundry, and dont load it up to the top with greasy, dirt filled work clothes, etc. (like some **) you will have no problem lol. We have Absolutely nothing bad to say about Maytag products, and the new set is amazing!!!!

My over-stove microwave is approximately 18 months old. Suddenly, the fan came on and will not turn off. I had to unplug the microwave. This appliance is out of warranty but certainly should last longer than 18 months. I feel that Maytag should certainly be called to task for selling and promoting such a shoddy, unreliable product.

Clothes do not turn over in the wash cycle. The clothes at the bottom get plenty of hard scrubbing from the agitator but the ones at the top barely get wet and never move down to the bottom. Insufficient amount of water enters the tub. The repairman says the washer is working as designed. Neither Maytag or Lowes will take back the washer. Worst appliance Ive ever owned. Bummer!

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

My original Maytag washer lasted over 25 years (still using dryer purchased in 1977). But the Maytag model SAV 4655AWW I bought a few years ago is a piece of junk! Not long after it was out of warranty, it started making noise. Not overly loud, but noisy. Since then, though it makes such a loud noise, you can hear it 3 rooms away. It leaks water from the seals, shakes and vibrates all over the place (even when level). The rocking appears to be due to pathetic self-leveling legs they put on the back of the washer. I had to put a 2x4 on the back side of the washer to keep it stable. That took care of the rocking, but still noisy, leaking water and now it gets off balance when spinning and stops. It also wont start sometimes and you can smell it overheating. The transmission is now going out of it. This thing has been one issue after another. What is worse about it is I saw in another forum that this washer wasnt even made by Maytag. Supposedly Maytag bought? After the purchase, they just put their name on it. I bought a Maytag because of the dependability of their previous products, so Im thoroughly disappointed in their company and products. If I had wanted a washer built by some other company, I would have purchased it versus theirs. If you purchase a Maytag, you expect to get a product designed and built by them. Ill never buy another Maytag product and Ill thoroughly research the product Ill buy to replace this hunk of junk. My advice would be dont waste your money on Maytag.

I have enjoyed my microwave and it has lasted 10 years so far. The only problem I have had is the handle coming off but I clip it back on. Also I changed the bulb. The microwave is over the stove and matched the rest of my appliances. Basically, I would recommend Maytag for any appliances that a person would need to buy.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

I have to agree with all these other reviews. This washer twists clothes and does not wash them at all. If you open the lid mid cycle you will see dry clothes on top... Isnt that the whole purpose of a washer? WTF. Steer clear of Maytag. They realize that theyre selling washes to Generation Xers and they can get away with it because we were the first throwaway generation. Great business plan Maytag!

A contractor purchased the Maytag MDB7609AWW2 dishwasher about two years ago. Sometimes it will start a load, but most times it will not. The light for high temp, heated dry and sanitize work, but the heavy, normal, light indicators will not light up. Im faced with either replacing the control board or control electronics. I was told Maytag is a quality product. I have not abused the product. The last dishwasher that I had lasted 10 years. I only purchased this one because of a remodel. I will most likely replace the control board since thats the defective part. It doesnt give me a good feeling about replacing the part since it’s obviously a defective part. I will consult Consumer Reports before purchasing another dishwasher.

I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012. It has leaked repeatedly onto my wood floor. The water also collects and freezes on the floor of the freezer. I already have warped floor boards as a result. I just got it fixed. The repair person said he has done over 200 of these repairs in the last year. He also said Maytag knows its a defect and has supplied them with replacement parts. The company apparently tells its repair companies not to discuss this with their customers. I have yet to contact Maytag, although apparently from others experiences that will be futile. Im willing to join others in pursuing this. I had a 40 year old Kelvinator which was still working well which I replaced with this refrigerator when I redid my kitchen.

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

We purchased a $700 Maytag range 2 years ago and recently the oven did not work. After a Maytag authorized tech came out and checked the unit, he proclaimed the circuit board was bad and needed to be replaced. Since these ovens only have a 1-year warranty - regardless of the price you pay - he said it would be over $450 to repair it. When I asked why so expensive, he stated that they dont price the parts - Maytag does. I decided I could buy a new range for that price and get one with a warranty so I passed. I then decided to contact Maytag because I was very disappointed that such a reputable brand would prove so faulty. After writing a very polite letter and emailing customer service, they replied with a pack of lies. They stated that they have no control in what the service company charges for parts and failed to offer any assistance. They did not offer any solution except to say, Sorry. Well, you can bet that I have already spread the word to all my friends and associates about this experience and my Facebook page lit up with comments after I posted it. I will never buy another Maytag product and will make it my mission to spread the word. I had a similar issue with my brand new HP laptop but after contacting them, they immediately reached out to me and offered to pay for part of the repair!! Thats how you take care of your customers.

I saw something on your website about Maytag Neptune class action suit back in late 2005. I have owned one, never was notified of the settlement, and saw this since I have a mildew problem also in my washer. They are not willing to do anything about the repair on my machine, but send out someone and make me pay for it. Since I bought it in 2002, I would want to know why was I not included in the repairs and why wont they honor me in this since I am the machines original owner. Help, I worry that I am not having clean clothes and it is contributing to illness due to mold spores!

This is our 2nd Maytag washing machine in 25 years- we upgraded to a newer model though the old one was still working. The settings on the newer model are perfect for our family and we love all the options. We love our machine. Thanks.

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

I purchased my Bravo (MVWB300WQ2) washer a little over two years ago. It took all day to wash some loads due to leveling problems. Example, you could not put more than two bath towels in at a time, even with the towel setting. The washer would stop and you have to re-position the towels. You cannot leave because it stopped so often. Also, the washer makes an extremely loud noise during the spin cycle. My most recent problem, it does not complete the spin cycle. My clothes are still very wet. I refuse to call service. Its just too costly. It would be the third time in less than 3 years. However, the first time was within the year warranty (no charge). The basket had to be replaced - it was ripping my clothes. During my second service call, the technician advised me in purchasing an extended warranty. I paid for the service call and for a one-year extended warranty which just recently ended. The washing machine is not worth paying for service again. I am going to purchase a new machine instead!

We purchased a Maytag washer/dryer 5500 series in October of 2006. It was working good for the first few years, then gradually started failing on us. The clothes would not be clean or they would be soaked when done. Two days ago, on the board it kept blinking LR. So I checked all measures to make sure that it wasnt the motor or the front door lock. That door lock is a big pain! However, it happened to be both the motor and the bearing at the same. This is definitely not worth spending another $700 on. Goodbye Maytag, hello LG!

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

Purchased a Maytag refrigerator less than two years ago. Model M1txegmyb that was nothing special. Main purpose was to keep food cold/frozen. Now it makes noise and will not freeze anything. We called Maytag and they told us to take a hike or pay $469 for a new compressor on a fridge we spent $650 on. I would never buy their products again because the quality is so poor. Reading the other comments we have decided to throw the unit out at this point as we have pledged never to give Maytag another dollar.

I have nothing but great reviews for my Maytag experience... In approx 1975 I purchased a Maytag W&D, Model MAH4000 MDE4000, when their advertisement was portraying Maytag repairmen as the loneliest repairmen. Maytag was so dependable that the repairman was NOT needed...and it was true... That Maytag W&D set lasted til approx 1998 when it was upgraded to the Maytag Neptune MAH4000 series... Had a minor problem with mold in the washer, but Sears and Maytag replaced the seal and made another modification... We also dried the seal at the end of the washing day and left the door slightly ajar between uses... Have not again had that problem.I have since given the Neptune set to my daughter and the washer and dryer are still in operation, WORKING SUPERBLY I might add... So I am searching for a good quality Model MAH4000 and MDE4000 to replace my current much older, yet functional Whirlpool... It may need some repairs and about a year ago, I spent $173 to replace the Pump which was clogged by a sock inadvertently stuffed around the top of the drum when too many items were pushed in at one time. I prefer not to throw additional money at this machine! So, if you know of a Quality pre-owned Maytag Neptune washer and dryer in the Lexington KY area, please contact me...

The Deli drawer randomly falls, shelves in general do not fit well. Rough edges on door corners are a hazard especially for children. Service call line was extremely poor with a total disregard to customer concerns. It has been a very bad decision!

We purchased a Maytag dishwasher model number mdb7749sbm in April 2013. March of 2015 the controls stopped working completely. We looked online and instantly found it was a problem among many others, and said it was a result of corroded ribbon cable. We opened the panel and, sure enough, inside the ribbon cable the electrical wires were completely rusted through! We called Maytag, and, of course, despite the numerous complaints of the same problem, they would only fix it if we paid $250, or send us a replacement part for $350 to fix ourselves. Not going to spend that much on a dishwasher that already cost $600 and only lasted 22 months! We are attaching a picture that shows after we tried cleaning the rust (when Maytag refused to fix it) how much of the electrical wires disintegrated! We tried soldering a small wire to connect it again, but the ribbon was so thin it just melted right through.

I recently bought a home that had a Maytag Neptune set. While they were newer than mine, I sold my Kenmore set, dirt cheap. Last night when I opened the washer door to take the load out, smoke billowed out. Im sick about this. There should be a recall on these washers!

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

I spent over $600 dollars on a Maytag Bravo 300 series. The washer has cost me over $300 to fix the latch and 2 months later, it will not spin. I would recommend to anyone not to buy a Maytag product! Garbage! I had a standard Kenmore washer that lasted over 10 years without a problem, paid $300 and still sold it for $100. The funny part is that I sold it to my brother who still uses it regularly and has not had any problems. So what is money worth? Your call.

Maytag Performa Side by Side fridge PSD262LHEB door handle pulled off for the second time since purchase but this time, the handle knocked over a pot of hot water on me. I am just relieved that I have no small children anymore. I would consider this very dangerous in any household. The first time, it was covered under warranty along with the broken ice maker. The repairman stated that he had replaced many handles and due to design flaw, they would not last long.

This washer (Model# MVWB765FW1) will not wash your clothes. Its not designed to give enough water for washing. That means some clothes will still be dry after agitator cycle; seriously. Thank you Maytag for going green! The repairman will tell you the machine is working according to design. That is true but the machine is a fraud as a clothes washing machine. The weight of the clothes in the tub tells the computer how much water to apply; good luck with that. We learned that if we add a bucket and a half of water, the clothes will come clean. Do you want to do that? Maytag used to be a good name.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

This Maytag dishwasher works great if you are using as a sanitizer for your dishes so long as the dishes were soaked already. It stinks if you do not use it often and requires a lot of bleaching.

We purchased our Maytag fridge on May 13, 2013. On June 19, 2013, it stopped working. We called Home Depot where we bought the fridge and they told us that we would have to deal with Maytag. What a nightmare. The repair guy came out and ordered a compressor for the fridge. 2 days later, when the compressor came in, the repair guy told us that the fridge was unrepairable. Great, what was I supposed to do with this hunk of metal now? I called Home Depot back, and they ordered me a new fridge, added a five-year warranty for free, and the Store Manager even dropped off a small dorm size fridge for us till our new one came in. Yeah for Home Depot!!!! I would recommend no one ever buy a Maytag product again - what a piece of junk. Their customer service didnt even care; they had the same old story - We will get back with you in 72 hours. Maytag was good when it was built in the US; now its just more China Junk.

The washer is not cleaning the laundry. Its a HE my butt. Its been looked at and fixed numerous times. It sits too long and it doesnt really agitate the laundry at all. Laundry is in the exact position when you loaded it when its done. Its the worst washer ever! I can clean the laundry better in the sink!

I purchased a Maytag Bravo Washer in October of 2011, I had a repair man come to check it since the spin cycle sounds like a jet is revving its engines in the laundry room. He told me that the repair cost is $493.50 to replace the transmission. The machine also has problems with the circuit board. The lid lock goes on and off and on and off so you cannot run the machine. Speaking to Maytag they just kept saying your warranty is over and we dont offer any assistance on the repairs. The machine cost $530.00 in 2011 and they think its reasonable to have repairs more than the cost of a new washer. They said they had no complaints on the model. My repairman advised not to buy Bravo, Cabrio or Calypso models since they all have the same problem with the transmission and electronics. I think they should at least pay for the parts, the transmission is $300. And we didnt even price the electronic part of repair.

I am very dissatisfied with this washer (Maytag Washer Bravos XL), it doesnt use enough water to cover the clothes. No matter which cycle you use, the clothes dont come clean. Who cares about water sensing if your laundry isnt clean. I will not buy another water sensing machine, I think the consumer should make that call on how full to fill the washer. Even on power wash the small agitator turns slowly. Not happy with this machine at all.

The refrigerator is barely over two years old and the bottom pan fills with water, freezes and leaks out onto floor. Is a very common problem with these refrigerators and Maytag is happy to pay for the new part to fix it, but will not pay for any person to fix it. They have known this is a problem for a while, but will do nothing to fix it. They clearly do not stand behind their product with a known ongoing problem. The Maytag repairman is no longer not busy. Will never buy a Maytag appliance again! Will take the new part and fix it ourselves.

We purchased kitchen appliances in 2012. A Maytag French door fridge, dishwasher and double oven range. So far my lights on the range have not functioned right as to which eye is on on the smooth top range, the ice maker burned out and now the control panel on the dishwasher has burned out. All of course are out of warranty. We have replaced the ice maker. Now in search of the control panel for the dishwasher. Havent priced the part for the range yet. I do know that I have a Maytag washer and dryer that so far are between 10-15 yrs old and knock on wood they work great. But I will NEVER buy appliances with the name Maytag on them again. So sad that you spend top$$$ for 1-2 yrs of the appliances working correctly.

The digital display on our Maytag Washer model MVWB765FW, bought 3/22/2017, failed overnight (whilst the machine was not operating) after 3 1/2 years. A reputable firm came out and diagnosed the problem, their report concluded that the Control Board had failed and needed replacing: they provided a verbal quote of $525 [ ! ] to do that. The machine cost $600 and based on the expected life for washers (per Consumer Reports) of ten years would have a maximum residual value of $420 based on straight-line depreciation. The retailer from whom we bought the washer told us that he had contacted Maytag and asked them what they were prepared to do about this failure: a week later and absolutely no response from the manufacturer. Apparently Maytag has no concern for their customers or their own reputation. We made the mistake of buying this machine based on Maytag’s reputation and a ten year warranty which appears to cover only parts unlikely to fail! NO MORE MAYTAGS FOR US.

We bought a Maytag dishwasher in August, 2014, and already the touchpad is malfunctioning and we cant start the dishwasher! I am very disgruntled and frustrated by this! I should have kept the old Kitchen Aid dishwasher that we bought in 1995! At least it never malfunctioned!

Is there any place to give a zero to this Maytag Front Load Washing Machine Model MHW5500FW1 and if there is a class action lawsuit please include us! We have owned other Maytag Washing Machines and never experienced such an epic failure as we have with this washing machine! We were so excited when we purchased our new Maytag washer/dryer set in March of 2018 we even remodeled our pantry/laundry room to accommodate them! As the chief operator of the washing machine, I have literally cried at what a mistake weve made! We have no complaint of the Maytag dryer. Let me describe my new normal procedure for laundering a load of clothes. First, load the washer with clothes then press power/cancel then press rapid wash let the clothes get HOPEFULLY saturated with water then hit hold to start and then hit power/cancel this shuts off the washing machine. I then press power/cancel again and select normal and the water empties out of the washing machine from the prior load and then starts to refill, if the add a garment light comes on (when it wants too) and no I dont change any pre-set settings I am able to add extra water with a pitcher, if this procedure works I let the washer run its 1-hour and 48-minute cycle. If not, I have to start over again because the add garment light wouldnt come on to allow the door to unlock. After the clothes are finished I again press power/cancel then hit rapid wash put my fabric softener in the dispenser press hold to start and let it run its 36-minute cycle making sure my clothes are rinsed appropriately and not stiff because of the lack of water. I neglected to say that when Ive tried tricking the washer and think I am able to add extra water, if Ive added too much the sensing kicks in and the washing machine drains all the water out on its own and refills with the little water it allows! Which is maddening! I throw up my hands and sit down and cry!!! I have contacted Maytag/Whirlpool complaining about the lack of water and their wacky water sensor! I asked them how can you conserve water and electricity when you have to wash your clothes over and over with long wash cycles? This doesnt make sense! My white clothes are now dingy and stiff as well as the colored. Maytag says you can use powdered detergents if its HE High Efficiency powdered detergents, but thats not true. The detergent doesnt dissolve and ends up on the clothes at the end of the long wash cycle because of the lack of water! From the beginning I adjusted the amount of powdered detergent for the front load washer and have to dissolve it in hot water prior to washing and hopefully am able to add it to the clothes if the add a garment will let me! I have now resorted to extra cycles to rinse out any remaining detergent hoping my clothes will be soft and fresh smelling. I had planned to replace my old Maytag agitator washing machine with this piece of junk front loader, fortunately we kept our old washing machine as a back up!

I have had it since 2011 and still works as good as it did back then. I love it. Hope it helps people decide when they go shopping for a dryer. I have a dog so I have to keep her clean so I wash a lot of her bedding and she sheds a lot. She also sleeps on the with me so that other bedding that I put for her on my bed between her clothes and mine which I do separate. The dryer works a lot and it is still going strong.

My $1,500 Maytag double oven Gemini has been trouble from the get go. 1st, trying to broil something cannot be adjusted. It sits 3 to 4 from the fire & there is no 2nd shelf. The control knobs sit on top of the stove & its easy to burn them when cooking. The broiler has always smelled like its leaking gas. Plus, the bottom oven stopped working & we had to get it repaired. The last straw was when the control board went out. We arent even going to try to repair, just going to buy a new stove. No Maytag!

I purchased this Maytag Bravos Xl Top Loading Washing Machine approximately 2 1/2 years ago. It broke down shortly after the 1 year warranty was up and cost me $300.00 to fix. A bearing had broke and needed a service call to repair it. Well, I paid about $800.00 to begin with, so decided to fix it. Today it started draining water from bottom of it. I call Maytag and after a 20 minute wait on the phone because they were having higher than normal call volumes! They cannot help me, other than to charge me for yet another service call and perhaps a repair. Whirlpool/Maytag makes a high priced money pit of a washing machine! Dont waste your money!

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

Please Do NOT purchase the Maytag Aqua Lift Gas Range. It does not clean anything, you will pay more money for a cleaning oven that does not clean any grease or droppings if you cook. This is not an Oven for any one, or family that cooks large meals or has gatherings. I had the technicians at my house over 4 times and they confirmed that this oven is not a self cleaning oven. It doesnt get hot enough as your self cleaning ovens. And MAYTAG did not want to hear anything, basically not clean much, but advertised as a self cleaning oven. Having been a Maytag customer for years I will never buy a Maytag product again. And we need to support American made, but not when the consumer is misled.

Bought a French door Maytag with freezer on the bottom. Ice build up on the bottom of the freezer and it has ruined my floor. We are replacing the floor in the kitchen. It is only a few years old. They have horrible customer service and will not replace anything.

I have a Maytag Series 3000 washing machine which, as many knows, is the same as a Kenmore. I bought the set 23 months ago and since then, I have had nothing but trouble. In my first three months of ownership, I had my first error code of which I had to replace the hot/cold water valve. Fortunately, the unit was under warranty. Since then, I have had to replace the CCU and MCU twice. Now, the units MCU went out again! Whatever happened to the Maytag name? How can I get this permanently fixed or replaced? Is there a lemon law for appliances? Any assistance would be appreciated.

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

1998 MAH4000 - I got this unit (used) in 2004 for $400, and it has pretty much kinda been a lemon ever since. I have babied it through until now, though it had the wax motor repaired twice (Im glad I bought an extended warranty from Maytag, but that added $400). Now the motor control has gone out. I like the concept of the front-loader, but my folks Maytags (and my grandparents) have run for 30+ years without any of the hassles Ive had.Granted, I like bleach, so the mold thing has been less of an issue for me, but wow. I have to say I wont ever purchase another Maytag appliance again. Im about to drop the $185 for a new motor (the motor control board went out, and apparently I need to get the new motor and control). Im pretty sure I lost a phase based on the burnt components on the board. Im glad I know a bit about electronics, or else Id really have been in for some money. Boo on this model!!

The refrigerator is not keeping cold. The freezer is full of frost/ice. I had this fridge looked at twice in the past. Its about 6-7 years old.In the past, Maytag was considered a high end product. I wonder where the manufacturing is taking place for most of the parts. Could be it was cheaper to go overseas and now we are all paying for unacceptable products.I will never purchase Maytag. Maytag should be selling products they can stand behind! Products that are made in the USA, where our standards are higher and we expect products that work!

I have a bottom freezer Maytag refrigerator that is about 4 years old. It started leaking and continued to get worse fast... It appears that the gasket around the freezer drawer does not seal about half way up. It causes a sheet of ice inside the freezer, so I am not sure if it leaks due to the ice defrosting. The refrigerator doors do not seem as if they shut tight either. After reading many of these comments about Maytag refrigerators, I am not sure at this point if it might be better to buy a new one rather than fix this one??? I looked for a recall and do not see one. Clearly this is a defective appliance.

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

My less then 6 month old washer presented an error code and stopped working in mid November 2021, so I contacted Maytag and they sent a service man out to my house. The service man was distraught and said it the washing machine had catastrophic failure - they would order the parts and get it repaired. Early January I still had heard nothing, So I again contacted Maytag and they had no answer.On January 26th I finally received an email saying due to parts on backorder I had been approved a new washer and JB Hunt would be handling the delivery and disposal of the original washer. On Feb. 07 - I contact Maytag, yet again, due to not hearing anything for almost 2 weeks - They stated that the request was not submitted properly and it would be another 5 days before a representative would be in contact with me. I am currently still paying on this brand new washer that does not work on top of 4 + months of laundromat fees due to not having a functioning washing machine and I am nowhere closer than I was mid November to a solution for this washing machine. I would NEVER recommend Maytag to anyone!!

This washing machine just sprinkles water on your clothes then ties them up in knots. And to add insult to injury, needs repairing every year or so. Horrible! It does have a couple of redeeming qualities, but they definitely dont outweigh the cons. It spins the clothes quite dry and has a large capacity. I have dogs and kids who play football and a husband who does construction, and its not unusual to find lumps of dirt and fur trapped in an article of clothing or blanket. All my bras and sweaters get ruined, it twists them up horribly. The blankets and sheets end up in a mushroom shape. Sad to say, NOT good. I like Maytag, but not BRAVOS.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

I purchased the Maytag Bravos XL MVBW755DW Washer and MGDB755DW Dryer in July 2016. Shame on me for not making my complaint sooner. They offer the Tide Pods for use but they dont completely dissolve and leave a residue/stain on the clothing. I have to wash everything on Deep Water Wash just to try to get them to come clean. Clothes will come out dry in some spots, they will have fabric softener stains on them, the pre-treated stains are still there once washed. Lint residue will be left on just about every piece of clothing. The fabric softener/detergent dispensers left side is rusting and I have to pull it out and clean it once a week. I cant get to the track on the inside to try to clean it and soon that will deteriorate and the dispenser will no longer slide into place. If I could attach pictures I would. Now moving on to the dryer, it dries clothes great. My only complaint at this point is that when the cycle is getting ready to shut off it sounds like a jet engine and rattles terribly. To sum this up, I called customer service this morning. They said nothing that I am explaining to them sounds as though it is a manufacturers defect. They said they will send a tech out to review at a fee of $99.95 plus the cost of any labor associated with the repair. They did however offer to pay for the parts. Now my question to them is if none of my issues are a manufacturers defect then why would you offer to pay for the parts? The unit(s) are no longer under warranty... Think twice, gather as much information as you possibly can prior to making a major purchase. I DO NOT RECOMMEND THIS PRODUCT!

Have owned washer and dryer for one year. Liked the styling, basic functions and the manufacturers reputation. Also liked the fact that there was a rebate on the pair. We bought the entry level Maytag pair from Lowes. Lowes delivered the units quickly. Thats the good news. The BAD news is (they) dont tell you when you buy the unit that you have to buy and use special detergents. One of the cycles on the dryer stopped working within ten weeks. But the REAL thing we hate about these is the fact that they are built out of PAPER-THIN METAL. If you push on it hard with one finger you will have a permanent dent. They proudly display American flag stickers on the units proclaiming Made In the USA. They should be more concerned about the quality of their construction. A local appliance salesman told us that twenty years ago (these) appliances would commonly last fifteen to twenty years. Today you are lucky to get five or six years (But then they get to sell you another, and another, and another).

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

I purchased an expensive front-load washer and dryer a few years ago. About a year after I purchased the washer, there was a foul smell that developed. I contacted Maytag and they informed me of the directions to follow - keep the washer door open when not in use and use Affresh tablets periodically. I followed these directions and was unable to prevent the washer from developing mold in the washer. Id like to file a formal complaint on my washer and dryer. I want a refund on it. I paid way too much money on these units to suffer. Here are the details on my units: Maytag 5000 Series with steam 4.5 cu.ft., Maytag Commercial Technology, Model: MHWE550WW01, Serial: CS00202582, Type: 199-02 732 WT/CR, 12 amps, 120 volts, 60 hz.

Purchased this maytag oven from home depot November 2011. Oven has been working properly since install. The top burner controls do operate too easy and you can just brush up against the stove and turn the gas on which I seen here was mentioned. My major issue is the stainless steel finish that was applied. It appears that this metal was not properly prepared prior to applying the finish. The oven door is with rust blisters. The metal under the coating is causing this problem. The finish in the other areas is with no problems... No chemicals have been used to clean this oven.Customer service of maytag stated that this stove only has a one year warranty... so if you buy any maytag just remember one year and when it breaks down the cost to fix will be more than a new defective maytag stove. I will not purchase another maytag product and I do not recommend that this manufacturer be considered when purchasing any appliance.

Two and a half years ago I bought a Maytag dishwasher thinking it was time to upgrade from my Ge. After a year and a half the control panel went out in in it! So For a little over a $100 I replaced it. Now, a year later, the panel has gone out again!!!! What is this? Every year I have to spend over a $100 to repair this thing!! I think it is time to find a new dishwasher!

We had remodeled our kitchen in 2009. Bought new fridge and stove (Maytag). The oven door came off and cant get it back on. No matter how many times we tried, no way can we get it back on. I had to have my son to come and help us. No sooner did we use the handle to open the door off again. This has been going on for 3 years. **, well fed up. I called Maytag about this issue and they told me they would get a repair at my cost. The fridge freezes all the produce, cant regulate the temperature. Never ever will we buy any Maytag product again. Who knows what’s going to happen next? Oh, and the paint is chipping off of the grates of the gas stove.

Dishwasher cleans well, but the control console has failed again & only responds to two functions. After replacing the console a couple of years ago with a new unit I thought it was done (it didnt get much use). Is there any recourse for this complaint? All I want is a new console panel. Maytags brand is apparently only good on the commercials. Very disappointing. Also, the top rack is very awkward & is only good for short glasses etc.

The first washer my husband and I ever purchased was a somewhat cheap top loader but it worked very well for over 10 years. We decided to fall for a bargain sale at Home Depot and went with the HE Bravos model. We were told that it would save us money and work great! From day one weve had issues. It never really seemed to clean right. It gets thrown off balance if you have more than one bath towel in a load at a time. After an angry call to the company and a somewhat helpful customer service rep, I began washing every load at the deep clean heavily soiled cycle and then did an extra rinse to boot. So much for energy efficient. So, fast forward 4 years, I HATE this washer but cant justify a new one at this time. Now, it stops mid cycle and I have to unplug it then plug it back in and restart it. When this happens, there is an awful smell. Needless to say, well be buying a new washer within a week or 2 and you can bet your life, it will NOT be a Maytag.

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

Maytag washer manufacture changes are not worth a dime. I suspect EPA made the changes, and engineering was made by someone that has never washed a load of clothes in the entire life. There is no agitator and/or supposedly made to conserve water. Well, it saves water alright with each load. There will be a 2 foot circle in the middle of a bed sheet that doesnt get wet; the same with a sweaters. I have checked with different stores and all made the same. And heaven forbid if you dropped a sock and wanted to add it to the load with the mate. The lid locks. I am both angry and dissatisfied and will tell this same story to anyone wanting to purchase a washing machine.

I have a Maytag microwave and stove in my condo kitchen. Both are about 4 years old. Ill never buy another Maytag appliance again. This stove had problems from day 1 and the support was dismal. I had [bought] an extended warranty, which covered nothing (I let it expire and didnt renew). The microwave handle came off in my hand a few months ago. I stuck it back on with gorilla glue. Now it is starting to shut itself off, as if it lost power then mysteriously turn itself back on. Im sure there will be a new microwave in my future and it wont be a Maytag.