wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

Not long after the 1 year warranty expired the washer started making noise while agitating. Long story short, the transmission is making the noise and should be replaced. It is a $200+ part. While it is still working ok, Im waiting for it to fail completely. Not good for an expensive washer. I dont think Ill buy Maytag again.

We purchased a Maytag front-load washer and dryer in October 2010. In March 2011, all bearings and the drum needed replacement. In July 2011, the pump needed service and now in Sept 2011, we were told a new drum and bearings are needed again. The washer is still under warranty by Maytag. We contacted Maytag to ask for an exchange or a refund but we were told that it wasnt possible.

The machine had automatic fill which did not allow enough water to rinse the clothes properly. I had to run another cycle to rinse the clothes. The machine was also extremely loud. When I had a warranty repairman come out concerning these two item as it was brand new, I was told I should have researched better. I gave it away after 3 months.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

I would like to say that I purchased the Neptune washer & dryer for my parents back in 1998. Up to now, 23 May 2015, not once has either of the machines required service and have been functioning well for the past 17 years. This is a testament to the quality and workmanship that is Maytag. This week I have purchased the Maytag Maxima front loading washer & dryer for my home because of Maytags reputation.

We bought a Maytag refrigerator around 2 yrs ago. Ive had repair out a couple and tried to take care of this myself. I am being told by repair men that it is a design flaw that the line gets plugged and water pours out all over my floor. The refrigerator I replaced was 20 yrs old, never had a service call & never poured water all over my floor. From reviews Im reading Im not alone in this problem. Needless to say Im less than happy with Maytag at this point! Model #:MBF1953YEB3, SER. #:K22812455, reciept #:** pd 1/19/13 DECKER & SONS 430 FULLER GRAND RAPIDS MI.

First off, everyone seeing this should be fuming as I am because we are mostly in the same boat with these control panel issues. Mine is Maytag model MDB7749SBM3 about 575.00. A little bit cheaper than most of you because I purchased at the online and had a rebate. About a couple months after the warranty expired, we started having weird light issues with the control panel where are one light would pop up when you didnt hit it or other lights would pop up when you hit something else. We kept dealing with it thinking that it would dry out and resolve itself. Lo and behold, just like it appears to be tens of thousands perhaps hundreds of thousands of machines, it quit. I read this consumer affairs post after it quit and now I know why it did. I opened up the control panel and sure enough, the little ribbon that connects all the electrical connections had brown on the back like it was burnt through. I was able to find a special 1 800 number that Whirlpool has set up because they have purchased Maytag and the woman I spoke with said they would send a technician out and that I was responsible for the diagnostic fee. I was born but it wasnt yesterday. I immediately said to the woman, Absolutely unacceptable. I am NOT paying for anything, very politely highlighting the fact that I know they settled a class action lawsuit in California regarding a control panel issue and there are hundreds maybe thousands of complaints on consumer affairs.com. The woman place me on hold, I am assuming to speak with her supervisor and then let me know that they would pay for the diagnostic fee. She said a repair date for me for about a week and a half later. The repairman had a good day because the dishwasher was already disassembled for him and he proceeded to take pictures and call Maytag. Maytag told him that I was responsible for the installation cost and service fee which according to the technician is about a hundred bucks. I told the technician that is fine but it will not be fine when I call Maytag back. I have not spoken to Maytag about the hundred dollars needs to file a claim for a new dishwasher and associated damages. I have not spoken to Maytag about the hundred dollars but I am only on this to let you know that every single one of us needs to file a claim for a new dishwasher in associated damages in small claims court. I plan on filing a claim for approximately $700 for a new dishwasher and damages. In my opinion, I feel like we should all do this, otherwise big corporations like this will continue to shovel garbage into the stores left and right.Have a good day and good luck with your court case hopefully. With all the evidence against them, I have a feeling that they will settle this and pay before the court date even comes around. Good luck to all of you. I will try and update this after I call Maytag back for the hundred dollars that they are going to charge to repair their broken part.

Maytag Bravos MVWB725BW - Purchased this washer last year and have been very unhappy with the way it washes. It is extremely harsh in the way the agitator moves the clothes. Because it has a low water level the clothes take quite a beating in the washing process. This is confirmed when I remove the clothes from the dryer and proceed to clean the lint filter. The filter is constantly full of lint, even after drying clothes that have been washed numerous times before. Additionally, the clothes, even though being put in evenly, end up bunching together.

We bought our set when they first came out at Home Depot. We gave a pretty penny for the set. The first complaint was soon after I got them home; the washer gets the clothes so tangled up its hard to get them out sometimes. The 2nd complaint is, for a couple months now, the UL light comes on and beeps. I have to open the lid, close it and it starts that part of the cycle over and it usually does 4 to 5 times before it actually spins and finishes. I put it in the shop; they said they cant find out whats wrong with it. They said the leveling rods are still new looking. I was like, I know its still a newer set. Its money for nothing. I called Maytag. They want to charge me over a $100 just to come out! Rip off! Do not buy this set. Beware! Im still having problems. I will not buy a new Whirlpool set because they bought Maytag out and I will not buy a new Maytag set ever again!

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

Worst customer service ever. I ordered my washer and dryer from home depot 2 weeks before a possible delivery day. The day before delivery I receive a call that they dont have them and I must wait 1 more week. After 3 phone calls I am promised a credit to my account. A week after delivery I am wondering where my credit I was promised is so I call. Im told the most I can be given is $100. I state that I feel my time is worth more than that. A supervisor is brought in and Im told we will get $150 credit. Then put on hold. She reviews account (why didnt you do this first) and told because we didnt call within 48 hrs of delivery the most they can give us is $75. So I call back very frustrated. Then Im told its our word against theirs that we were offered that?!? What?!? Well I am sure you record conversations and thats total BS. I explained how you cant offer something then take it back. I was told the week before I was getting a credit and my account already notated. No one said, Call within 48 hrs to dispute again to get it. Why would I have to I mean seriously. So after a total of at least 2hrs on the phone before and after delivery I am forced to settle with $75. I feel very unappreciated. I purchased and paid for $1633 worth of appliances that were a week later than promised. Called less than 24 hrs before expected delivery and told they dont even have them. Then told Im getting a credit of $150 to be told sorry now just $75. The lady proceeds to say that she doesnt think it was because of the phone call not being made. What? Are you serious. WELL THAT WAS THE LAME EXCUSE I WAS GIVEN SO I COULD CARE LESS IF IT WASNT THE REAL REASON. THAT JUST MEANS I WAS LIED TO. I promise I will never buy Maytag Whirlpool again. One customer may not mean much to you but good customer service means everything to me.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

We purchased a Maytag washer and dryer from Lowes in the summer of 2016. The washer performed so so. Not a great machine. After only two years use, there is only my husband and myself, the transmission went out. The repairman said it would be cheaper to buy a new machine than repair it. Maytags 10-year warranty does not cover the transmission. We replaced the Maytag washer. I cant say anything good about Maytag.

I have had this range (Maytag MER8775AS electric range) for 36 days. The hot surface indicator light doesnt come on (bulb is fine) and the heat elements turn on and off on their own when I am cooking. 36 days! This thing is junk! I am going to see if I can return it, even though it is outside the 30-day window.

My built in electric double wall oven, Model MEW6630DDB, convection on the top, has been the most frustrating appliance I have ever owned. It has never kept an even temperature. It has been repaired several times and still does not keep an even temperature. It takes 14 hours to cook a 20 lb. turkey and baking cookies are not even an option. I have complained to Maytag and have paid for repair services. Their solution buy an extended warranty which is absolutely insane because they havent been able to repair it since it was new over four years ago.

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

Bravos washer, a year old machine, needs new main electronics board $220.00 plus $125.00 labor to install. Repair guy said humidity makes them go out. Go figure a part sensitive to dampness on a wash machine. Why don’t they seal it better? By the way, this machine does not wash, worth a crap. I am getting something new.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

I bought this Maytag dishwasher model # MDB7749SBM2 and of course it ran great until the warranty was up and then the touch pad started acting up where if you would press normal every other thing would light up. I replaced the keypad and then the controller and its working at this point again. The keypad ribbon cable had a big burn mark in it and by all these complaints it seems like an issue Maytag has and does not want to address. Luckily I work on electrical and was able to do this myself and I had no labor but over $300.00 in parts. What upsets me is I bought because of the reputation and the Made in America on it and it was replacing a 20 yr old Kenmore that was still working great when I took it out. With all the complaints about the same issue Maytag which is Whirlpool would step up to the plate and fix this. No more Maytags/Whirlpool for me again.

I purchased this machine and after 2 loads it started making a very loud and awful noise. Maytag sent a local service person and he found a screw that had come undone and was in the motor. Since then there are a few strange noises that the machine makes during different cycles, usually involving spinning. Called Maytag and then sent repair person. This young man was non-verbal, was probably 20 and it was impossible to communicate and try to figure this out. Person sat through a full cycle and he said the noises are because the machine is out of balance. Well, why did the sync system not balance at the beginning of the cycle. No answer to that. He reported to Maytag that nothing was wrong with the machine.Machine is still making noises and I cannot wash a small load or it will still be wet at the end of the cycle. I am a widow and live alone. I dont wash large loads. So I called Maytag again. They dont care. Finally they agreed to send another 2nd opinion. I have a lot of videos of the machine making strange noises and the repair kid does not care...lots of blank stares from him. I highly suggest not going with Maytag. They dont back up their products and they leave you with a bad machine. My LG FL was perfect. Never an out of balance load. I could wash a single item with no problem. MAYTAG IS A TERRIBLE COMPANY.

We bought a Maytag dryer from Lowes on 4.23.20 for $567.87. From Day 1, it required us to dry even medium loads at least 2 times and sometimes even 3 times. I have been complaining to my husband since we got it. The clothes come out smelling almost burnt. But if you dry it once, the clothes are wet. And if you try to dry it the 2nd time for less time, its still not dry. So, it takes forever to do laundry. This morning, it sounded like a lot of metal was rattling around. So, I looked inside to see if change was in there, and nothing was in there but t-shirts and socks. It had been drying for less than a minute, but when I opened the door a wave of extreme heat hit my face. Now Im afraid to use it because I think it will eventually burn our house down. And with COVID-19, we do tons of laundry. We cant afford another dryer but may have no choice.

It has never failed me and I cant remember when we purchased it. When I grew up, my Mother only used Maytag Washer and Dryer. When I married (almost 50 years ago), I purchased a Maytag Washer and Dryer and have never regretted it.

I purchased this washer approx. 2 years ago. It will not spin. Called 3 repair men, only one would look at it. The cost to repair is more buying a new one. I am buying another washer and it will not be a Maytag. Seems from other post live on this washer is 2 years. My son has one just like it, told him of the problems. He is thinking of selling and getting another one before his quits. There are 5 in his family.

Maytag washer MVWC565FW - Clothes do not wash. They just get pushed around and the soap scum is left on the clothes even with the water at the highest level. I bought the washer override lid switch at a appliance parts store just to observe the washer cycles. The washer did not wash the clothes. I took the washer back. I like Maytag products but this washer has to be engineered.

Weve had our Maytag dishwasher for less than 4 years when the control panel quit. The repairman came today. He was here 10 minutes and it cost us half as much as a new dishwasher. Its just the two of us and we use the dishwasher once every 4-5 days. Almost laughed when the repairman said the part and labor was under warranty for 90 days! There is no quality control anymore. Just greed.

I bought the largest Maytag top load washer. From day 1 clothes come out with laundry detergent left all over them. I have to take a washcloth and wash off every piece of clothing coming out of the washer. Had a technician come out. He said he gets this complaint every day. His suggestion, put less clothes in and use less detergent. This washer is programmed to use minimal water and it just doesn’t have enough water to clean all the detergent off. So, I bought the biggest washer to wash bigger loads and now you are telling me that just doesn’t work.Spoke with Maytag customer service. They said very rudely if there is no problem found when the technician came out, there is nothing they will do. She told me it was user error. My dryer also stopped working. Sometimes it would turn on, sometimes not. The technician said the lint screen error code came up. He would try to get Maytag to replace the whole board but usually they don’t do that unless the whole board has a problem. Called Maytag the next day. The technician documented he fixed a connection problem and closed the ticket. What???? So, now I guess I need to schedule another service visit. Very unhappy with 5 month old appliances. Paid $1700 for the pair, you expect quality products.

If you dont want your sheets ripped, then DO NOT purchase this machine. All my sheets have been torn, and many items of clothing damaged beyond repair due to this machine. Also, the machine started rusting out the first year I bought it (see photo). The repair man said that I must be doing something wrong - of course, its the consumer and not the machine - ha! Maytag should have given all of us a huge credit to a different machine because they knew of these problems early on. Never again will I purchase a Maytag appliance.

I am about to replace the control panel on my Maytag dishwasher (MDB7749SAM1) for the second time since purchasing it in 2012. Additionally, I have replaced the door gasket twice, as it becomes loose and does not properly seal, causing water to leak from the door during the wash cycle. There are many documented complaints of corrosion on the control panel ribbon cable necessitating replacement of the entire unit. If there were a way to replace the ribbon cable instead of the entire panel, it might be a bit easier to swallow the repair expense. Either way, it is ridiculous to have to spend almost 1/3 the original cost of the dishwasher to make it usable again, and twice in only 5 years time! My previous dishwasher was 30 years old and still functioning (though noisily) when I replaced it with this expensive lemon. I have not contacted Maytag, as it is not in warranty, however, it seems that a major appliance should last longer than a couple of years without issues.

After everything posted here why would anyone take a chance buying any Whirlpool product including all subsidiaries. I made the mistake of buying a Maytag washer and dryer less than 3 yrs ago. There are only 2 people in the household and we only wash linens, towels and undergarments- the rest goes for dry cleaning. The washer stopped filling with water, similar to what was posted by another customer. Maytag customer service was 2 weeks out.When the service tech arrived he diagnosed the problem as a faulty water value but didn’t have the part- another week. I asked the tech why it takes 2 weeks to get someone out for a service call- he told me that there were 4 techs working the area but 2 quit and they were never replaced. The tech went on to say that he was leaving because of the misdirected grief he gets from customers because “the Whirlpool brand is crap”, it takes to long to get service and usually the cost is more than the appliance is worth- and they take it out on him. That is not hard to understand.Bottom line- IF THE SERVICE TECH IS TELLING YOU THE BRAND IS “CRAP” what else do you need to know. FYI- Maytag repairman quoted a new water valve at $70, labor $150 for a total of $230. I paid $600 for the machine- is this a joke? The exact same part was available on Amazon for $43 and was delivered in a day. With the help of a YouTube video I replaced the part in 10mins. On top of the fact that the appliance is crap, it would have taken 3 weeks to get fixed- Maytag is also screwing customers with overpriced parts that shouldn’t have to be replaced in the first place- fair warning, STAY AWAY.

I am a regular customer of Leons and used to buy all my home appliances from them, because I trusted their quality and service of their products. However, last time I bought French Door Maytag refrigerator from them, about two years ago, we suffered from defects in this type of fridge. The problem started before one year when my wife saw some leakage of water on floor in the front side under the fridge freezer door. In the beginning, this was occurring once a month or every two weeks, so she didnt think it would be a problem or it might happen occasionally. However, the water leakage now became worse and almost every day. We had to put a towel permanently under the freezer door to dry the water which appeared ugly. Also, I had couple of accidents that my child slide over because of that water leakage. I spoke to one technician, he told me resolving this type of problems is not guaranteed because the problem will appear again or after while. He said this could be a manufacturing defects in this type of Maytag fridge models!!! Another problem appeared also one year ago, that one of the door handle started to shake very little, but now it looks like moving from its position and there is no way to fix it!!!Therefore, when I requested the help from Leons they told me that, You didnt buy the extended warranty and we cant do anything for you!!! You can talk directly to Maytag. Then, I send email to Maytag explaining the problem. They even didnt bother to reply or call me. Now, I feel that I was bluffed by these companies. I didnt think that I was buying a $2,000 refrigerator to scrap it after two years. That is ridiculous when you buy defected product from them, but they dont care to resolve the issue.

First off. Maytag customer service is horrible. I purchased a Maytag washer & used it 8 time. It now doesnt rinse the soap out of my clothing or even clean anything. The washer isnt broken because thousands of other people with the same exact washer have written negative reviews everywhere online. The washer needs to be recalled & never sold again. Maytag is making people SICK and they dont care. My whole family had skin irritation because we didnt realize our new washer wasnt rinsing.

We bought Maytag refrigerator MTB2195 AEW in 2006 for a hefty sum. The store where it was purchased was closed. The place where it was serviced was closed. We have had seals replaced, fixed, etc. twice. The freezer is full of ice balls hanging. The refrigerator doesnt keep as cold as it should and stays steamed on glass. I had a repairman again today and was told that he cant fix it. The frame will not stay tight. Theres a 3/8 in. drop from left side to right. It cant seal properly. You have always been a great product. Whats happening here? What can you do for me; Im at wits end. I have an older refrigerator in the basement thats 26 years old and is still going strong. I need something done quickly as I dont want to wrangle with this ice any longer and shouldnt have to. Please give me your attention on this as soon as possible. Kathy

We purchased a Maytag Centennial line washer (Model # MVWC400XW0) and paid a little more hoping that it will last longer than a normal washer. After just 14 months, the washer breaks and we are forced to buy an extended warranty from Maytag for $300. The warranty price seemed a little high; however, the only other option was to buy a new washer. The repair guys showed and said it should be fixed.After just three weeks, the washer broke again with the exact same symptom. Since I had the extended warranty, I called in another ticket. A different repair guy showed up and he said the first guy messed up. He said the guy misread the diagnostic code and didnt even put in the part that he said he replaced. The repair guy checked with Maytag and they told him it was no longer cost effective to fix our washer. Really? They overcharged for the warranty and wont even repair it when it breaks. The only reason I can think Maytag would do this is that they know the washers are junk.

This machine that I bought 2 1/2 years ago is very loud. Sounds like a helicopter that is going to hit the house. Last week the machine did not empty and would not spin. What a mess. We had to take the clothes out and try to wring them out by hand. Then we had to scoop all the water out. Had to call a repairman to fix it. $187 which included two trips to the house and a new pump. The pump was $56. Just the last year my grandson came to live with us, but before that there were just two of us in the house to do laundry for.

Maytag Bravo model MVWB750WQO. Bought this washer in 2009 for 1300 thinking it would last at least 10 years! Wrong! I loved it until a few months ago when it started making VERY LOUD noises during final spins. Sounded like the house was going to take off. Then today it started leaking water. Repairman said it needed a drum, seal and gasket. Would have cost 700-800 to fix. Needless to say we bought a new washer today, and it wasnt a Maytag!! For that much money I was expecting the washer to last a long time!

I bought the machine at Lowes. It was cheaper than the regular old agitator washers which should have been a clue. I like the old agitator washers that fill as you put in the clothes. Lowes installed it, turned it on and did not seem to care that although water should have been entering washer, none did. They rushed out. Ok, my water to the washer was bad so it was a simple plumbing fix. Less than 1 year the machine was full of water and would not agitate, spin, drain or anything. It sat full of water. My brother looked at it, fixed the hose that was no longer attached and it worked! Yeah for 1 year almost when again the belt came off, fixed again. Trying to find correct belt is starting to annoy me. I want to take it and dump it. It looks pretty but is nothing but a piece of crap. Maytag, shame on you!!!!

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

This washer has a fault with certain types of blankets. Parts of these blankets come out shredded. We end up replacing these blankets. Other than this problem, the washer has worked fine.

First of all, the hoses that came with my washer leaked and were cheap made. My husband put the hoses from my old washing machine on the Maytag. Then, I hadnt had my Maytag washing machine but about two months when I had a problem with the mixer. I had to turn the hot water connection off in order to wash in cold water. When I called the store to explain the situation and ask if they had their own serviceman, the person I talked to made me feel like a complete idiot. He said in his twenty something years of selling Maytags, he had never heard of such a thing. Anyway, when a serviceman finally came, he also had to replace another part due to a recall. Now, my washer is right at four years old and is leaking from under it. My husband checked the hoses, and they are not the problem. I bought a Maytag thinking I was buying the top of the line but I guess I was wrong. I will not buy another one nor recommend them.

Maytag has really gone downhill. Had trouble with a factory defect in a new French door Maytag refrigerator within a few months (had it returned) and now the Maytag Centennial EcoConserve Top Load Washer no longer spins after only just barely 2 years of use... I will NEVER buy Maytag again. That is a promise. I will put more money and buy more expensive products from your rivals if it means avoiding Maytag products. That is my advice to anyone reading this review. The washer was used for MAYBE 10 loads of laundry per month... Yes, just for two people who have desk jobs so It was never stressed out. Used HE laundry detergent. Quality is a thing of the past for this company. Your reputation is in the doghouse.

I purchased a Maxima washer and dryer set, along with the pedestals. I had the set delivered to the new house the kids and I are moving into, but didnt use it for 2 weeks as we had not moved in yet. Guess what? I used the dryer 1 time and the drum stopped working. I called and got tech out. Motor is not working. They had to order a replacement, then back again to replace. Guess what? Less than a year later, same thing happened and another two visits from tech, motor was replaced. Get the pattern? And now, less than 2 years after purchasing and another two visits, motor drive and control board were ordered. They have not been installed yet. I have sent emails to Maytag and on the second one, they actually called me. The lady didnt think there was anything wrong with the fact that it broke after the FIRST use. Her reply to me was, But we fixed it... At this point, 2 years and 6 tech visits, three new motors and a control board, not to mention my time taking off from work and being held hostage waiting for the tech, they could have replaced it and saved themselves some money. They have lost all credibility. I am about to try regular mail to a supervisor. Wish me luck.

Sears washing machine model # mvwx500xwo - This machine is the worst. My mother who is 87 years old smells like mold every day due to the smell that comes from this machine. Im not sure whats going on but the plumber told us there is something very wrong with this machine. Its not the hot or cold water that smells, its the machine. I am now concerned about my mothers health. Please advise if you will allow us to purchase another machine with some kind of a credit due to the serious issue this machine has.

Maytag Bravos Quiet Series 300 washer/dryer - Purchased this set nearly 3 years ago from Lowes. The washing machine smells like toxic sewage. The Affresh brand cleaner no longer works. All of our towels and many of our clothing items have had to be replaced due to the stench. I surmise this is because it does not use enough water. The clothes get wrinkled badly, twisted, stretched out and torn. The dryer does not fully dry. Always had to run it again to get the items dry. Finally, it started making a horrible, loud, screeching and grinding sound. Neither the washer or dryer was quiet for long. Putting these out on my curb today for scrap metal pickup.

We bought top load washer model # MVWC425BW1 at Lowes brand new 9/22/14 for $493.93. On 11/23/2017 it stopped working and would not even come on after lid locked. Found out it needed new parts that would cost us over $300 to fix and we could buy another new washer for $400. We are very disappointed that this washer with only two people only worked three years when we thought we had bought a reliable product that would last. Sent several messages in November but no response till today 12/13/17 after filing. BBB complaint filed and they decline to do anything. So this company just wants to sell products but has no customer service. They only give a year warranty. Of course if the product is not going to last they want you to buy more.

We bought a Maytag Centennial Washer in 2011. 6 months ago the control board went bad. Maytag has an exorbitant replacement price! I went to Ebay and bought a NEW board for 1/7th of the price Maytag wanted. The old board was marked revision B. The new board is revision F! That indicates to me that the board was defective when it was new and they have made 5 attempts since then to fix it! No recalls however. Now the motor is shot. I found out the motor from Australia is also inferior! So this 5 year 3 month old POS Maytag is going to the dump! We will shop for something made outside the US. No not a Samsung. I think there should be a class action suit against Maytag.

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

Purchased Maytag Washing Machine from Lowes in Alexandria Louisiana on January 12, 2021. Today is April 16, 2021 and it will no longer wash clothes and has horrible burnt smell coming from it when on wash cycle!!! Tried contacting Maytag Service but was kept on hold for almost 1 hour. I setup a service tech using the Maytag Service online and supposedly a technician will be here on Monday April 19, 2021....of which I seriously doubt will even show up based on some other reviews.Maytag as well as Lowes are SCAMMING people out of hard earned money by selling such garbage!! If LOWES or Maytag really cared about its customers it would see these Negative Reviews and do something about it. Lowes continues to sell this garbage which is why I am blaming them as well! DO NOT DEAL WITH LOWES OR MAYTAG PRODUCTS - YOU WILL REGRET IT!!!!

It is not worth the money. I paid $2500.00 for a Maytag refrigerator that I had for two months. Two service calls were made to Maytag as of 07/07/2014, the problem no ice and the refrigerator stays warm. The problem has not been resolve and Maytag refuses to replace the item.

Prior to purchase, I did my due diligence and read reviews about this washing machine. Apparently, they were written by Maytag employees, because this washing machine has been a major disappointment. Yes, it tangles clothes and sheets, but I feel that is to be expected since it is HE and uses less water. I will give it that and I dont have to dry nearly as long. But that is where my positivity ends. Clothes dont always come out totally clean. And then there is the issue with the horrific grinding noise. The machine has been making a progressively louder, angry, grinding noise with a high-pitch end note. And as of today, a horn type noise has started. Lovely.I anticipate the machine is on its last legs and I have only had it a few years. I spent too much money on this and feel like I have been misguided and, quite honestly, ripped off by Maytag.

The bearings and motor went out in less than 3 years. The warranty good - the dealer I purchased from Siano Appliance gave me credit to purchase another Maytag washer - which I had to purchase an additional warranty for $320. The new Maytag is less than 5 months old - the motor has been replaced and waiting on a tech now to fix it. It would not come on. SO in warranties I have paid over $640 and am still having issues with the new washer. The first time I purchased a warranty for 10 year - when the machine was replaced I had to purchase another warranty for that machine - now if I have to replaced this one that will be an additional $320. IS this legal?

I purchased a washer in July and its already off track. When I seen it I know it was junk but the sales person assured me it was a good product. 3 months later its off track. No spinning. DO NOT WASTE YOUR MONEY.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

The efficiency of cleaning even dried on foods and getting them perfectly clean and dried is unsurpassed. And the need for dishwashing soap is always at a minimal using this Maytag Dishwasher.

We have the 4000 series front loader washer. Within 8 months of owning it, it would shut off in mid cycle. You have to unplug it to restart it. Then, when it completes the cycle, it is still soaking wet. So, you have to put it through the drain and spin cycle again. There is something major wrong with the spin cycle. It takes about 2 hours to do one load of laundry and you have to stay home to do all of the steps. It costs as much to fix it as the machine costs. It’s the worst washer we have ever had. No more Maytags!

I have had 2 Geminis. The first one was fine, this second one is a mess. I have had at least half a dozen parts replaced. I have insurance to have this oven repaired but have paid to have the window seal replaced on at least 3 occasions. The top of the oven is so hot that when I have used the burners to cook on top I have received 2nd degree burns. I have received burns on several occasions. I asked dealer if I could trade this in but said I would have to sell it on my own. I would not subject this oven to another person as I feel it is very dangerous.

Same as all the others, bought this dishwasher about a year and a half ago for a new home. Didnt get the CO until 3 mo. ago and already having same problem with the keyboard flashing and not working properly. Very pathetic to believe less than 100 washes and were going to need a new washer, that works out to be about $ 5.00 a load. Wish someone could help. Model mdb7749sbb0. Thanks.

Ive owned the stainless steel version of the Maytag dishwasher model MDB7749SBM purchased on Sept 6th 2013. July of 2014, my first control panel went out. Lights not responding. Was within the 1 year warranty period. Now, that panel is acting up again. I called Platinum Factory service and they wanted to charge me for a new panel and the labor. Well, I used a few choice words on how I felt and the customer service person said the part would be free. Well, nothings free as I scheduled a visit by the Platinum Factory Service. They of course call 5 times to make sure you are home. The day of the service, the tech calls me to see if Im home. I of course said I am... then, he goes to tell me the labor charge for him to come out and hourly rate will come to $189!!! I said screw it and dont bother. Maytags quality and engineering SUCK. Avoid them...

Just bought a washer and my clothes are always left with dust and dirt on them after washing. Called Maytag, they sent a technician over, but he found nothing wrong. Company refuses to do anything about it, including exchanging it for a different model, since weve had it for more than a month. I am extremely dissatisfied since I just lost over a grand on a washer that doesnt actually wash my clothes.

This machine (Maytag Bravos XL) was in our new house and is relatively new. It is the worse machine I have ever owned. I am 58 and cant reach the bottom of the tub to get clothes out. It doesnt fill with enough water to clean the clothes, and repeatedly I have my clothes coming out dirty. I have had to rewash clothes to get them clean at all. Or they come out with grime all over them. I had both a LG and Samsung front loaders in the past, if I could afford it I would throw this Maytag out on the curb! Its a piece of junk.

Our Maytag washer 4000 series was installed on September 2010. Within 12 months and 5 days, we are now waiting for our second spin bearing to be replaced. It is a repair that takes 2 guys and 2 hours, and they basically have to replace the guts of the machine. I can imagine this is, at minimum, a $500 repair. We didnt buy the extended warranty, but luckily, the appliance shop was able to talk Maytag into eating the cost since we were only 5 days out. With the purchase of our new house, we upgraded from our appliance allowance to this model. With everything going on with the new house and selling our old one, I didnt do my normal internet searches for customer reviews and that was a mistake!Maytag has since sent us a warranty extension offer for $350, covering 3 more years. I guess Ill be buying that. It sucks that you pay top dollar for a washer only to find out that you have to pay an extra 40% just to keep it running for 4 years. No more Maytags for me, ever. Note to Maytag, you sell junk and your business goes into the ground. You are selling junk! Stop trying to squeeze every penny out of design and build, or you wont have a job.

Bought a new Maytag Over the stove model Microwave from Lowes. It worked fine for a while. Then it started saying open close door. We opened the door and closed it, and sometimes it would work. This went on for a while till it finally would not work at all. Called for repair, the service guy came and took it apart and one of the door switches needed adjusting. He left and it was working, good deal. 2 days later open close door started all over again. We found if we lifted the door when closing it, then it would work sometimes, until one day it would no longer work. We called for another appointment, and got a new company to fix it called ABCO. The service guy showed up and tightened a screw and it worked again, said the other service guy might have forgot to tighten it down. I tried it and it worked. We did not touch it again till next morning and back to open close door again. Called ABCO back and got a new service time for Wednesday next week. Wednesday came and went, called to see why no show. They said we were not on the service list and were very sorry. So we set up a new time for them to show the following week Tuesday between 12 and 3 pm. At 3:49 they called and said sorry, but they were not going to be able to make it today. I told her then get us tomorrow and was told they were very busy and maybe Thursday would be better. I told her we were in line and and should get service before others that came on later. Her reply was maybe Monday of next week was better. After the runaround she said they would try for Wednesday tomorrow, but no promise made. After that I called Maytag direct and they said nothing they could do except make another service appointment. She told me I could get a service appointment tomorrow Wednesday between 8 and 12am or 12 and 3pm. I asked with who this time and was told ABCO who just told me they were too busy to show up tomorrow and had put me on standby. In the meantime I paid over $300 for the Maytag microwave that is never going to need service because the Maytag service man is so lonely. And bought a $ 200 Panasonic counter model so we could have a working microwave. So now we are in over $500 and still no Maytag working microwave. They did send me a letter offering me a discount on extended service plan if I want one. I told them it would be cheaper after the one year runs out under warranty, to just junk the microwave because it has cost me way more in wasted time, waiting for the lonely Maytag repairman to show up. Bottom line do not buy a Maytag Microwave model MMV4205DS-1 unless you just want a good looking decoration over your stove with a nice light, and have plenty of time waiting for the lonely Maytag repairman.

I purchased a Maytag Bravo HE washer and dryer! The biggest mistake I ever made! Three inches of water is max for a load of clothes! This is max full or actually empty. The washer was a third full of clothes and only the bottom layer was wet when it went into rinse! After pulling a calf I really wanted the top pants washed. Nope. Went in dirty and dry to the rinse cycle to spread the bacteria throughout the load. The soap was still laying on the dry clothes on top. Repair guy spent two hours and couldnt get enough water to at least dampen all the clothes in the wash cycle. I would like to see how much cow afterbirth bacteria was still in clothes. I didnt buy a machine to dry wash my clothes! I have asked for my money back on the pair through the performance warranty. Well see! I am not giving it a star as it doesnt earn one!

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

It doesnt agitate enough to move clothes around. Doesnt put enough water in tub, even on deep fill just barely gets to the top of clothes. Washed a shirt 3 times by myself to get dried mud off of it. 3 time it was washed bumy its self. Clothes do not to get as clean as they did in the old style washers that had good agitation and the agitator that was bigger than whats in these new ones. And water. Need water. We arent trying to dry clean. And even thats done with a liquid that totally covers clothes and moves around better than this garbage I have right now... Looking for an old washer to replace this one... HATE HATE HATE THIS WASHER.

Lets be real and say that people with good experiences dont often end up on websites writing reviews because they are busy enjoying their product! I purchased my set in early 2012 and will admit that initially there was a learning curve with using a washer with no agitator. I enjoy doing laundry and Im really good at it but with this washer I had to change my routine. Always pretreat stains. Deposit clothes loosely around the drum and shake clothes loose before putting them in the dryer. My clothes come out great! I have a child, two dogs and a greasy truck driver man and everyones clothes smell great. I can wash my king bedspread and anything else in my house with no issues. And my washer has never torn any of my clothing, however fragile. I dont iron often and I hand wash nothing.I give 4 stars instead of five for the extra steps to ensure my clothes are clean and wrinkle free. No they dont make things like they used to but thats with all the new stuff. My moms 3000 dollar Samsung set (her washer) isnt working as I write this. Too bad more people with good experiences dont get online and share. Hope this has been helpful.

My wife and I bought a Maytag Bravos at the suggestion of a store employee at Lowes. Since we have owned it, I have seen the reviews and the washer has been a total let down. We have experienced all the same complaints. Loud noise, door lock not working, not enough water in the drum to wash clothes, and the bearings going out and it doesnt work. NEVER will we buy a MAYTAG again. To the scrap yard I go today. Thanks MAYTAG for wasting my money. Thanks LOWES for recommending this garbage.

Ive had my washer for about two years and have been disappointed from the get-go. I did a lot of research and found this to be top rated... Wrong! Even though I use the HE detergent and Ive even cut down the amount with no results, it leaves gobs of soap/lint residue on most of my darks and I wind up having to either rewash on clear or rinse by hand to get rid of the stuff.Ive also noticed some snagging on some brand new towels, but I attributed that to possibly the brand. Well, then I had an issue with some very expensive bottom sheets shredding and raveling and still didnt catch on. Today I noticed a different towel with similar problems, which led me here and walah! I see Im not the only one having these issues… Darn! Warranty is expired and Im stuck!

Have a Bravo Quiet Series 300, does not clean clothes because on not enough water to wash with. Have to set it on Bulk to have it clean good enough. The way it agitate and rotate the clothes turns the wash into knotted pretzels (this also makes it harder to clean the clothes) which in turn makes the spin cycle vibrate badly. Cannot put wash in and leave because of this.

Received new washer & dryer on Oct 2nd, 2015. The dryer has been acceptable, but the washer has been one problem after another. First of all the washer is so noisy beyond belief. The engineering is one dreadful design. At first attempted use, washer would not begin cycle. Sensor would say lock, unlock, lock, unlock for so long, I would cancel & begin again. It became such an annoyance that I placed start of cycle on a timer (it sat at sensor mode for 20 min.) then I restarted next time sat for 15 minutes without starting. After beginning from start position it would start OR NOT. First repairmen told me timer might be off a bit. As days passed with same issue, second repairmen arrived and found that door was off (not completely closing). Repairmen would place an order for new seal. Upon repairmen arriving for third time (new seal did not solve issue) he believes that lid is uneven, & he will order a new lid & return in a few days to repair. I must admit that service has been quick, but the issue is still a headache. I would NEVER recommend this model to anyone and would like for Maytag to replace washer with a different model. The noise is a factor that no one should have to endure. The grinding noise can be heard from three rooms away from laundry area with laundry room door closed! Im absolutely a very very unhappy customer.

Maytag Dishwashers work great. It cleans well and appearance is very good. I have always trusted Maytag appliances. Its quiet running and also energy saver. If I had to replace I would stay with Maytag.

First front loader washer and love it. Saving on water, less tangling of clothes. So far they are quieter than others that I have had. The dryer is almost 10 years old and the washer less than a year. The machine I had previous to this was top loader that had to be replaced, would no longer spin.

We bought a Maytag refrigerator two years ago with the front french doors and bottom pull out drawer. We chose Maytag because we thought it was a name we could trust, a good quality merchandise. However, in the last two months, we started having problems when the fridge wouldnt stay cold, the freezer worked fine. We removed everything from the freezer and my husband found the freezer needed defrosting as the back of the unit was a solid sheet of ice. It took hours to defrost and we thought that we had the problem taken care of.. and that we wouldnt have to worry about this happening again. However, we have now had to do this three times in the last two months!! I love the style of this fridge..but am getting SO ANNOYED with having to rip everything out of the freezer and spending HOURS to defrost it! I have NEVER had this problem with any other fridge!! Im ready to replace it, but weve only had it for two years, and I shouldnt have to be spending a fortune on ANOTHER fridge after TWO years!!

I purchased my Bravos washer in 2011. Three days before the warranty was up, the motor went out. It was leaking oil and had to be replaced. Two days later it quit working again I had to have another repairman out and found that the gear shifter had popped off so he put it back on and charged us 85.00. Luckily my husband watched him repair it and knew what to do if it happened again, which it does just about every 2 or 3 loads so I have to pull it out and pop the ring back on. I waste more water than I save with this machine. I have to drain the water so I can move the machine out and start all over because they didnt wash, and that wastes more soap. I would get laundry done cleaner and faster if I beat it against a rock. This is the worst washing machine I have ever owned and I will never buy a high efficiency washer or another Maytag again.

I have never owned a Maytag in my life but was told it was the best on the market. That is so wrong. I purchased my Maytag Bravos washer and it has been a nightmare. Never again will I buy a Maytag. I have replaced two belts. It never spins the clothes out. Always have to restart it to respin. It turns off in the middle of the cycles. It will take hours and hours to do one load. At this time it just puts up the minutes and counts them down...does nothing. I am just fed up with this washer. I also bought a Maytag Centennial Commercial dryer. I have replaced a belt once. I would highly recommend not buying the Maytag Bravos washer. Save yourself the headache.

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

Maytag Neptune was purchased over 15 years ago to replace GE, which we purchased when children were little. I wanted a step up in quality. I remember paying around $499 for this unit. This is an analog unit. The intellidry feature has been a real asset, protecting our clothes from over drying. We have had this machine for nearly 20 years. It has been real reliable, sometimes drying 20 loads a week. Large capacity, but has to fit down a narrow and twisting stairway. Must be energy efficient, have good reviews and decent price. We always look for sales or buying incentives. Brand is secondary to quality. Knowledge of an appliances historical reputation is important. I would look at reviews, especially concerning cost of repair. I would attempt to get a hands-on view, before purchase from a reputable supplier at the best price. My dryer has only required one major repair in the time Ive had it. A few years ago we replaced the motor and blower, and I have personally replaced the drum support rollers twice. I hesitate to replace this machine, because the analog controls have proved very reliable.

We purchased a Maytag Front Load Washer in April 2011. We did not purchase an extended warranty. From the beginning, it didnt seem to clean as well as our 12 year old top load Whirlpool had. Then in Summer 2013 it began to create fabric pulls in fine fabrics - tablecloths, blouses, etc. Whirlpool sent a repairman who charged $90 to tell us that the drum needed to be replaced because of a rough spot. He ordered a new drum and we understood that it would be replaced because it was within the 5 year manufacturers warranty on drums, but we would have to pay for installation. 2 months later, Whirlpool informed us they could not supply the new drum. Why are replacement parts not available for a 2 year old machine? The customer service rep told me that they would replace the machine for 15 percent of the cost of a new machine. All I needed to do would be to pick out a machine and let customer service know the model number and they would make arrangements and contact me re: payment of the 15%. When I contacted them again I was told that I would be expected to pay $508.00. That is 15% of a $3000.00 machine. It it completely unfair. Later, I was told that the first rep I spoke to must have been wrong because they dont pro rate replacements on a percentage basis. I told them that I was not interested and they have lost a good Whirlpool customer. In the last 15 years we have purchased 7 appliances made by Whirlpool. Never again! I am not impressed by their customer service.

I hate my new Maytag washer and wish I had never purchased it. Theres no way to control the water level in it, and on sensor mode, the clothes are barely wet and rubbing against each other creating wear. Things come out with soap stains and twisted up so tight that I dont believe water got close enough to the dirt to carry it away. Dont waste your money.

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

Washer when using sometimes my clothes are full of soap residue. The screen did not turn on. After unplugging it for a few minutes it finally turned on. Dryer gives a warning to clean the airflow. I clean it and the error never clears. I use my swifter to clean it and I still get the error. I finally took out the screen and so far no error.

Echoing the sentiments of others on this site, I am deeply disappointed in Maytag brand appliances manufactured by the Whirlpool Corp. When, for the first time in my life, I was able to buy all brand new kitchen appliances, I didnt even consider any other brand but Maytag. This was based on many decades of using Maytag products and watching my mother use them. I come from a big family so our appliances got used hard, and the Maytag brand ones worked year after year, decade after decade with little or no maintenance. To put it quite frankly, my new Maytag products are junk. I could supply a whole laundry list of problems but, in the interest of space, will just tell about the latest. A couple of weeks ago the fake tin foil paint on my oven and burner knobs just started falling off, revealing cheap plastic underneath. When I called Maytag to complain, I was asked how I clean the knobs. I told them that when I clean the stove front I remove the knobs and drop them in warm water with a couple drops of Dawn dishwashing liquid for the few minutes it takes to clean and polish the stove front, and that I had been using this same procedure for 2 years. The rep. hemmed and hawed awhile and then went away to consult her database. When she returned she told me that one is not allowed to soak the knobs per the manual, and therefore she could not offer any help. She then generously offered to transfer me to the parts department, where the rep. informed me that replacements would cost $70 EACH, thats a total of $350 plus shipping for 5 cheap plastic knobs. WOW! What a deal! I tell everyone I meet NOT to buy any Maytag branded product, and to apply extreme skepticism before considering any Whirlpool product. (BTW - the last certified Maytag appliance repairman to come & fix one of the appliances essentially admitted they are junk.) Model #: MGR8775AS SN: R32810432.

Horrible Refrigerator MSB27C2XAM00. I bought this refrigerator November 2013. Over the past 5 months I have made over 10 calls to Maytag customer service. Each phone call averages 30-45 minutes in length. In total I have and have had 6 service repair visits. Within 4 weeks of acquiring the unit, the letters on the ice/water dispenser wore off. They replaced the panel and within 4 weeks the letters wore off on the replacement panel. The subsequent calls made to customer service were regarding slow water dispensing and shrinking ice cubes. I was advised in order to maintain water speed and decent sized ice cube production I would have to replace the filter every time the water dispensing slows, which is on average every 4 to 6 weeks (each filter costs $40).When I asked why I would have to change the filter so frequently when the packaging instructions with the water filter states you can expect an average of 6 months use or 200 gallons, (mind you we are a family of 2 adults and one child under the age of 10 surely not consuming 200 gallons of water within 4 weeks), Maytag advised me to attain a whole house water filtration system. I was told that the water supply to my home must require extra filtration which is why the filters are not lasting. I asked if other NYC residents have made such complaints. Maytag advised they cannot share this information for confidentiality reasons. I told the rep that I did not want specific names/address of the complainants. I just wanted to know if there were any other similar complaints! If its the NYC water supply I would have to believe there would be similar complaints. Maytag would not advise.They will not budge in replacing the unit. After spending $1,400 on this refrigerator I am now expected to invest $500 annually on water filters in order for the refrigerator to work properly. I was also advised that if another service tech came to my home and the issue was found to be the same I would be responsible for payment of the service call. I did my research before purchasing this Maytag product. I ultimately selected Maytag for their reputation. I am so disappointed with this unit and with the company that I will never purchase another Maytag appliance and I will advise everyone I know to never purchase from this company again. Such a disappointment!

I purchased this Maytag washer/dryer set in February 2017 and I am very, very happy with it. This is a brand that has proven dependable for more than 80+ years. This is a low water washer that saves money on energy bills. I love the extra large capacity and was very concerned how well it would clean without an agitator. But having confidence in the name, which is why I purchased this set, I was very pleased with the cleaning power. The only disadvantage I see is with the soak cycle which is timed. I would like to have an option to soak indefinitely. So if you are trying to remove blood stains, you may have to use the soak cycle a few times before all the blood is removed. (Assuming that you are only using cold water and no additives.)

Purchased this dishwasher about 1 1/2 yrs ago. Luckily the first two times the control panel went out, it was still under warranty (within the first year). Now its gone out again! This is the third time! What happens is all the buttons will work except for the START and CANCEL. This has been the same issue every time. I tried restarting it, made sure there was not a leak that somehow was getting to the internal electrical components in the panel. I actually know the Maytag repairman by name. Its nothing like those old commercials where the Maytag repairman sits around and has all the time in the world because their products never break. Those days are over and these guys are busy working to fix these devices they label as dishwashers. Since my warranty is now expired, it was an unexpected $96 service call to tell me what I already knew - Its your panel again sir, it needs to be replaced. Well have to order one for you and itll be $265 for parts and labor plus the $96 service call = $361 repair for something that will likely break again in a few months. Never am I buying a Maytag product again.

MDB77495852 - I purchased a brand new Maytag dishwasher 2 years ago from Sears. A year later it broke down with what was apparent moisture in the control panel. Thankfully it was covered under warranty. Well guess what... it broke down again a year later and now just missed a year. But not it matters, the retailer (Sears) said it was not covered so Im supposed to pay about $300.00 to get it repaired. And figure I will have to do so next year also. I was told there is a Lemon Law for appliances but it does not kick in for 4 years. So after $900 in repairs I could get a replacement... REALLY? I think a recall is in order!

We purchased our double free standing gas range about 6 years ago. Our top oven went out about 4 years after purchase. We purchased the extended warranty from Sears and it was fixed at no charge. About a year later, the top oven would not work again. We called Sears, our warranty was up so it would be a repair that we would have to pay for. We decided to go with the Maytag repair service since it is a Maytag appliance and we had to pay anyway. The repairman came in and said that the top box that holds the electronic in it had fried wires and it would have to be replaced. So for $480, he could replace it. It was more than likely caused by a power surge. I just read that this also coincidentally happened to someone else so I find this cause to ask more questions. I also note that the top of the oven behind the burners where there is some sort of vent gets extremely hot (I accidentally touched it and had a blister the next day) when the oven is being operated. This is directly under the box that holds the electronic components. I would think that may have something to do with the wires frying since it is that hot directly below the panel. Could this be a defect in the building of the stove? Has anyone else had this instance beside the one person that I read about on your website?

My son gave me a Maytag washer for Christmas 2013. I hate it. Sometimes it takes me 5 tries to get my clothes washed, and then it dont go all the way through the cycle. I have to constantly check on it. I hate it. Can you give me some tips on what may be causing this... Very disappointed.

We bought our new Maytag top loading washer and matching dryer about 2 years ago. I am a busy woman so I havent had the time to write a review, but today being my day off, once again I find myself frustrated and disappointed with this set. The washing machine has a huge capacity, which was a huge selling point for me, however, if I put more than a small load in, the clothes come out still dirty, stinky and even have dry spots on them where they werent even in contact with the water. Even on deep fill it cleans the clothes inadequately, but at least they get wet. The dryer leaves the clothing rough and wrinkled unless I use the delicate setting, which I do for all cloths, and I use fabric softener liquid and a dryer sheet.I had a front load washer and dryer before, and my clothes came out clean and beautifully soft, but I replaced them because of the musty smell problem from the washer. I wish I would have kept them and figured it out. This set is the worst and I spent so much money on them. It takes so long to wash a load of laundry, and there is no way to interrupt a cycle without it draining and starting over completely. I have tons of laundry to do and I started 2 hours ago and the first load is still going. Geesh!!! Dont buy a Maytag. I paid for the extended warranty, but they are not broken. They have sucked from the very beginning.

Maytag Bravos top load washing machine - This is the worst washing machine I have ever used. Like some of the other complaints it leaves lint on your clothing. It does not put enough water in the machine. The so called smart technology that senses your load does a terrible job. Your clothing is halfway out of the water, with dry spots, even after 10 minutes of agitation. I am constantly adding 3 to 5 gallons of water to my loads to get things in the water. And if I want to let thing soak for a while you have to unplug the machine, because after 10 minutes it will automatically drain the water out. 2 years of dissatisfaction. I cant wait for it to die. I should have come to this site first. Never buy a machine without an agitator!

I depend on my front loading Maytag washer. It is very reliable, does a great job of cleaning even difficult items like comforters and pillows as well as items deeply soiled. I use the many features like water temp and level, fabric type, heavy or light load, etc. The only complaint I have is that the front cover of the detergent, fabric softener and bleach drawer came off and the exterior paint on top of appliance is rusting and peeling. A stronger substance for the surface where often detergent, fabric softener and other substances are often stored and they leak.

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

I bought a Maytag dishwasher in 2019 in Home Depot for my new home. The dishwasher stopped washing dishes after two years and 6 months. The price of the new machine was 700$ and I did not buy the extended warranty. The trouble is circulation pump, that cost to install the new one from local service would be about 350$ plus the new pump 150$. I consider quality is very poor if the new dishwasher works only two years and then it is better to buy a new item than fix the old one. Never never buy Maytag production.

Purchased this Maytag microwave brand new on April 2017. In January 2019 began to have issues with the display reading open/close door. Maytag would send a repairman for $160 to take a look at the problem. Parts of course are extra. I will never buy a Maytag product again.

I purchased Model #MHW563HW Frond loading automatic washer a little over 1 year. The options are not for me. The quick wash is way too short 20 minutes, all the rest of the options are 51 minutes to 2 hours & 57 minutes! If you wanted to add some extra minutes to the Quick wash you are out of luck. Normal wash is 55 minutes but can last much longer, it takes forever for this machine to balance which adds time to the process.I had an LG front washer before this one and when the clothes came out they were almost dry, not this washer, they are very wet. Then there is the horrible odor that comes after you use it, Ive tried drying every area making sure there isnt a drop in it. Still the stench is unbearable. Yes it has a Clean Washer with Affresh option which takes an additional 128 minutes and you have to do it at least once a week! Thats a LOT of wasted energy. That just doesnt sound efficient to me, washing the washer. Why??? This washer had great reviews which I read, not one mentioning these issues.