I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

My dog had to be on a special diet to recover from a stomach disorder. I placed 1/3 cup of dog food plus chicken broth and baby food in a bowl. I intended to heat it for seconds. Minutes later, my dog was whining and sneezing. I immediately returned to the kitchen to find the food and bowl were completely charred. The biggest problem however was from the plastic splash guard that melted down. Smoke filled my home. I had to call the fire department. I was coughing and had difficulty breathing. The smell was horrible!The insurance company and I have had thousands of money in restoration cost due to the damage. I was out of my house for weeks and got very sick due to returning to the home that was not remediated properly (allergies and asthma). The microwave was an over the range Maytag MMV4205BA. I would like to find out if the fire was due to a malfunction in the microwave oven. If so, Maytag should be paying for the damages. I still need living room furniture and carpeting replaced due to smoke damage.

Maytag fridge is a overpriced, ticking repair bomb. The fridge had issues with the compressor, control board (motherboard) and relay switch within a 12-month period. Customer service is weak in troubleshooting techniques and try to send the file over to a repairman. The repairman will show up at $80/hr + other fees and parts costing you approx $500, and still uncertainty that this fridge can breakdown at any time. Final advice: DONT BUY.

One year and 1 month after purchasing dishwasher, the lights on the control panel would move around and if I close the door all the way it will begin to wash. I have not contacted distributor about repairs. After reading all the reviews, I think I will just use it until it quits. Will never buy another Maytag.

Purchased a Maytag Bravo Quiet Washing machine. Nice and big for our family and uses less water. Generally okay with it (occasionally need to rinse clothes again as they have streaks/spots after the hand-wash cycle due to low water feature). This year it started making a loud noise while spinning, obviously the bearing. Googled reviews on this washer, reviewers explained Maytag now owned by Whirlpool and not the quality it used to be. Called the repair line, Whirlpool refused to say whether or not this would be covered by the limited warranty, even though it is very clear which part is causing the problem. The only way they would tell is if someone came out, then we were charged $149 for 5 minutes of looking at the machine to be told it isnt covered. In the end we will order the part and fix it ourselves. We will remember not to buy Maytag again.

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

We recently purchased a Maytag refrigerator, love it, no problems until the mystery person in my house accidentally broke the slide out door for bottom drawer. So I called Maytag, and with no questions asked they sent me a new part by Purolator! Great customer service makes everything better! Thanks Maytag.

I love it. Laundry as well as horse blankets. It does it all! I have never ever had one problem with it. Love the delay start setting as well as the extra rinse cycle.Easy to clean the gasket and keep the soap dispenser out to air between washes!

Hello, My recently purchased dishwasher has leaked water within less than half an hour of the fifth time to be used and showed error: F8E4, dishwasher model and SN are: Model: MDB4949SKZ. Serial # : FA3003347. Registered: 09/11/2021, Ive been calling Home Depot who in turn asked the installer to check the connection, and the latter advised and reported its a manufacturer issue. And calling Maytag for several times but no response or action. On-line service scheduling of Maytag is not working!!! And the live chat is not helping, as well. Now my dishwasher is not working since more than two weeks, knowing that it has been installed only a month ago.

Bought top of line Maytag dryer and washer in 2011. Immediately had problems with dryer. Dryer resets timer itself to outrageous times. Clothes so dry they could have been parchment. This has continued with multiple service calls and electronics replaced. Still continuing but they will not act lemon law. I have extended warranties but get runaround everyone including Sears where I bought it pointing to each other. Tech came out today and said problem was the way the dryer is. No way to change it. I guess that is nature of the beast. I will never buy Maytag or from Sears again.

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

WE bought all new Maytag kitchen appliances and the extended best service contract. Cost 1/2 of the cost of the appliances. This was 3 years ago. Recently dishwasher went blank. Service call was a factory neutral wire. Then ice maker replaced with a reman unit. Then we thought something was wrong with the oven cleaning system aqua lift. So after many hours and calls two service techs told us the system will not clean the oven and after many cycles it will not and the bad part is they are still selling this system to the public. Criminal. I think they should own up to the public when they do this kind of thing. On top of this I would go buy the self cleaning oven but the tech even said he will not use it because it will break and need replacement. It is no better other than you can use oven cleaner to clean the finish without the heating element and you cannot use anything that works on the aqua lift finish. Bad deal.

I have had the Maytag Bravos washer since November 2010. This washer does not clean clothes. They are never even submerged in water. Had I known this, I would never have purchased it. The salesman at Sears surely didnt mention it. I remember being disappointed at the fact that there wasnt a washer in the place with an agitator. I am disgusted with the washer and the company. I realized that it has been over 12 months since we purchased it, but most people do not feel the need to investigate what is going on under the lid of their washer. I unfortunately assumed that the washer was going to wash! Silly me. No, it does a little spin spin and a little spritz of water (literally, thats it) and at the end, you are left with funk concentrated in the creases of your twisted up, stinky clothes. No agitator plus no water equals no clean! The smell is awful. Someone else described it best - a mildewy basement.Anyone else who is claiming that their clothes do not stink with this machine are surely being deceived by strong perfumes in their detergent and fabric softener. To get a true idea of what their clothes really smell like, they should wash a few times with a scoop of borax and no fabric softener. Then tell us how they smell. I am convinced that the entire line of HE washers is a sophisticated line of crap! They use such small amounts of detergent because that little bit of water going into it will not get any more soap out, much less sweat, dirt and lots of other nasty stuff. This may not be a big deal to other people, but it is huge to me. We have a small homestead. Our clothes get dirty. We spent several hundred dollars of hard earned money on a name we trusted and they do not care.Every load, every day, I am reminded of this fact and it infuriates me. Im not typically one to write in complaints, but as an American citizen where there is a free market (somewhat), I have an obligation. If a product is really good, the makers deserve my praise. Likewise, if the product is really bad, the makers (and refuses to compensate in any way) deserve my complaint, as do my hardworking fellow Americans shopping around for a new washer. Stay away from Maytag and if at all possible, stay away from HE machines. It is so true that they dont make them like they used to.PS: Maytag tried to blame this issue on government regulation when I called. Im sick of this passing the buck. I am fully aware of the chokehold government regulations have on business, but they only hurt small business. To act as if this is not a partnership between the government and big business (like Maytag) only adds insult to injury. Take a look at the money spent lobbying by this company. Disgusting. The good news is, any success they currently enjoy will not last.

Maytag MCT Washer & Dryer - I bought the largest capacity to save time. However even my 6ft tall husband has problems reaching the bottom to remove clothes. Even worse is the lack of water to clean clothes, washes so long it wears clothes and they are still dirty. I tried to improve on my old Neptune and Id love to have it back. I may have to junk this washer. The dryer is very slow. Buying this set was tossing my hard earned money in the trash.

I have a 4 year old Maytag refrigerator, model F2557HE, with French doors above and freezer below. The compressor is dying, which amounts to total failure of the fridge. Periodically the compressor tries to start, there is a whirring sound that lasts and lasts and repeats as the food defrosts. Then mysteriously hours or days later it starts to run again and the melted ice cube bin turns into an iceberg. The appliance repair company tried replacing the starter to no avail, and now tells me it is the compressor itself. Each time it stops, I transfer my food to the 30 year old Whirlpool in the garage which still works fine.

Bought this machine summer of 2018 when my old washer went out. This machine is impressive looking but that’s about it. Clothes don’t get clean. Half the time they don’t even get wet! I’ve had to wash sheets two or three times to get them clean and wet. When washing jeans there is always lint and white debris on them when the wash cycle is done. I’ve tried all different settings, I’ve tried different detergents always the same problem. Wish I’d never laid eyes on this model at Lowe’s last summer. Gotta say, worst purchase of an appliance I have ever made. Don’t waste your hard earned money on this piece of junk!

I purchased the Neptune HE pair because they are front loading and can be set on pedestals to raise them to a comfortable working height, plus the brand and reputation are both excellent. I like that the chimes can be adjusted from low to high, or turned off. The front loading washers clean so much better and with a lot less damage to items than washers with center agitators. Looks are secondary, thats for sure. Functions like warm/warm cycles and being able to adjust to whatever load needs to be washed is really most important to me. Any appliances with a good, proven track record of reliability with few repairs is high on my list. Expensive appliances should be made to last and be of durable quality! No cheap plastic or weak-looking welds or components, thank you! Quiet operation and dependable cleaning and drying are top in my book, and this pair has exceeded even my picky expectations in total overall performance. They are 11 years old now and look & function like new! I had one minor repair on the washer at 5 years, and not a single problem since. With front loading washers, its important to keep the door open a little when not in use so that they dont get a musky smell. Ive gotten into the habit of using laundry boosters to help clothes, sheets, and towels smelling fresh longer, and putting a small amount in the washer drum has kept my whole laundry room smelling nice. Purchasing the pedestal drawers to set the washer and dryer on added extra storage to my laundry and its much easier for me to load/unload them at this comfortable height. Im totally spoiled by it now, so when I use someone elses laundry room (when I visit) I am reminded how nice my own setup is.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

The Maytag Bravos XL Gas Dryer I purchased less than a year ago has stopped working three times. The dryer stops producing heat. I am now about to call Maytag repair again and waste time and energy setting up a warranty service call. I spent a lot of money in order to go to the Laundromat on a Sunday. Do not purchase this dryer if you would like to be able to dry clothes at home with any type of consistency or confidence. Arrrggg!

Just had the repairman here. This machine is computerized so it won’t last. It does not have a setting that lets me do any load of laundry the way I need to do it. I have to use heavy duty to do a load and then it takes 2 hours. When I want to do a load of sweaters on delicate it will not put near enough water in the machine to wash them. The normal cycle does not add enough water to wash, let alone rinse the clothes. I can’t choose the size of the load based on how much I need to wash so I have to do more loads at 2 hours each or do everything on bulky. Whoever came up with all this needs to be fired. I am extremely unhappy with this machine and I have loved Maytag for years. No more.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

I had purchased a brand new Maytag refrigerator and in less than a year, the ice dispenser stopped working. I had called Maytag warranty department in regards to this matter and they flat out said, There is nothing we can do about it. I will never deal with this company whatsoever and wouldnt recommend it to anyone about it. Less than a year and they refuse to fix the item they sold. No better than a used car lot attitude.

This oven has been used so very seldom that I didnt feel I could rate it until now. We use the oven 1-2 times a week since purchasing it in March of 2018. There hadnt been any reason to use the Self Cleaning part of the oven until last week. I have had a oven with self-cleaning for 20 years and the oven went out so we purchased this one because of its sleek look and features. However last week I decided to use the self-cleaning setting on it and came home after being gone all day to find that the house smelled like it had a fire burning in it. I ran to the oven to find the whole inside cover in a white powdery substance. It looked like a snow blizzard had gone on inside of it. I was use to a small amount of white residue being inside the oven after it finished and it just wiped right up. We spent hours vacuuming it out then scrubbing it down with vinegar water and a sponge with a scouring pad on it. The casserole spill was still on the bottom, most of the enamel is gone and the glass will not clean off. I did not use any chemicals in the oven prior to turning it to the self-clean mode, I believe that it overheated and burnt the enamel off and distorted the glass. Whirlpool offered to send me a cleaning kit. I told them that would do no good. I had already scrubbed and used a razor blade to try and clean the bottom and the glass and them sending me different cleaning supplies would not fix the fact that 80% of the inside protective coating on the oven is gone. Now it is a porous surface. A Serviceman was scheduled and he called prior to arrival today and asked me to explain what was going on with my oven. I explained and he said I can almost guarantee that Whirlpool will say that it is cosmetic and they only cover cosmetic for 3 months and that I will have to pay for a $100.00 service call. This is a load of crap. This coating is part of the oven to keep it clean and protect the metal from the high heat of baking in it. This is not cosmetic feature like the outside stainless steel finish or the black trim decor. The inside doesnt look pretty. It is a function. See the photos below. Whirlpool Range Item # 805150. Model # WEE510S0FS.

I bought a Bravo washer 4 years ago from Home Depot. The spin cycle is stuck on high speed and sounds like a jet plane. Repair man came and said don’t bother to fix it because the bearing is gone. The machine cost close to $900. The repair man charged over $100. We are two retired senior citizens who dont do lots of laundry. I have read numerous complaints about the Bravo washer very similar to ours. Elder abuse should protect us from Maytag’s thievery and lack of help in repairs and replacement. A class action should be in place to address the Maytag Bravos manufacturing defects. There should be a recall and some type of reimbursement on this product . Please help us with this unjust situation.

Purchased a Maytag washer and dryer 6 years ago and everything was fine until 3 weeks ago when the washer stopped spinning. We knew we were out of the 1 year warranty and contacted a repair service, who told us the bearing was no good. Contacted Maytag who offered in goodwill to pay for the parts and we would pay for the labor. A different repair person came in and told us the washer has no bearings but a transmission, which went bad. They ordered the transmission and today the repair person was in to install it. He installed the transmission, but while trying to take out the old one he dented the drum. According to my husband the repair person banged so hard that it sounded as if something could have been damaged, sure enough it was the drum. Contacted Maytag to see if anything can be done as now we still have no washer, and the repair person was their selection not ours. All we got from Maytag was they are not responsible and there is not much more they can do. I cannot believe the last Maytag product we had lasted over 20 years and this one is less than 6 years with problems. Will not purchase another of their products again.

This washer was the biggest disappointment I have ever had. When I looked at it in the store I was excited that the tub was so big and the Maytag Label has always been trustworthy to me and my family. This machine certainly has disillusioned me against Maytag. I can only wash clothes on the bulky sheet cycle because even with deep water wash it only puts about 2 of water to wash clothes. Clothes on top dont even get wet! It doesnt take an engineer to figure out that you cant wash clothes without water. Big mistake! Would never recommend this washer to anyone! I complained directly to Maytag and never received a response. I have had to rewash clothes because they did not get clean. Even with an extra rinse the clothes still have enough soap in them to make my skin irritated. My whites are not white even though I use hot water and follow all of the directions provided with the machine. If there was any way I could afford it, I would throw this machine out to the garbage and get one that actually cleans the clothes. I will never buy another Maytag machine in my life. 

I have spent a lot of effort leveling my machine, and my wife balances the load very carefully, but 10 times during a cycle, it will start slamming the tub around, so loud you can hear it from the street. I, like others in this forum, thought I was buying the best washer in the market, and paid extra for the Maytag name. It sounds like from the other complaints, that my problem is just the tip of the iceberg. It will cost me $200 to replace the suspension rods. I wouldnt mind paying the money, if I thought it would fix my problem. After reading about all of the other problems with the Bravos, I might just cut my losses, and get a new one. What a waste of $1,000.

I mistakenly purchased the Bravo XL top load washer. I only wish I could give it a zero rating. I have only tried to wash 3 loads of clothes. It is almost beyond belief that anyone could possibly think this could clean anything. My husband actually watched it “work”, and insists I call Maytag because they must have forgot a part! It does nothing but crumple/wad the middle items together and rub them...and only them...together. There is no movement of the outer items until it spins. Maybe Maytag should enlist people who actually do laundry to “test” the items they put their brand on. I know the government and the energy rules have added to the complex problem of buying something as simple as a washing machine...but this piece of junk is almost laughable to watch as it destroys your laundry. I’m almost embarrassed to let anyone know I bought it. Thankfully, I have 30 days in which to return it.

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

Further down on this page is my complaint about the dishwasher. This complaint is about the company. This will demonstrate how cheap Maytag is. I filed a copy of my complaint below with the BBB, who in turn forwarded it to Maytag. They sent me a form with rules that they call Dishwasher Recall. Maytag will send me a $250 Prepaid MasterCard, providing that I: 1. Remove the old dishwasher myself. 2. Destroy the machine and/or render it inoperable. 3. Sign and date under PROOF OF DESTRUCTION AFFIRMATION that I have complied. Statement on the form (Your signature is your confirmation that you have complied). 4. Purchase a stainless steel machine (over $700). They list models you should buy. 5. Record on the form; Model Number, Serial Number, Purchase Price, Store where purchased, and Date purchased. 6. Send the signed Rebate Form back along with the sales slip. (Sales slip must show clearly Purchase Date, Purchase Price and Retailer Name). 7. Allow 6 to 8 weeks from the time the Rebate form is mailed. Are they kidding?! If I were to buy a machine at Home Depot, they will deliver, install and remove the old machine. I dont think I would take a Maytag dishwasher for free.

Purchased my Maytag in November of 2010, with the freezer on bottom. Within 1 year the ice maker stopped working, and every 8 to 10 days it gets a sheet of ice on the bottom, and water runs out all over the floor. Guess, Yes the warranty expired and scared to death that Im gonna have to replace my floor. If there is a class action suit out there please inform me.

Pleased with all the features. I have had zero problems with this Maytag refrigerator; no problems with the ice maker; the crisper works well. The adjustable shelves are so convenient.

We purchased this washer 8 months ago, and still do not have a working unit. From the very beginning of installing the new washer we had repeated F4 and E1 error codes. A technician was sent out three separate times and they replaced the ACU each time only to have the same error codes recur. This unfortunately took 5 months as each time the ACU part was on backorder. After 3 failed attempts they agreed to replace the washer with a new one. We were dumbfounded when the new unit arrived and we had the same F4 and E1 error codes! They have again replaced the ACU and still we have the same error codes! They are sending yet another ACU but we have little confidence this will work and we are at a painful 8 months with no washer.

I purchased my Maytag Centennial 1 and 6 mos ago and it is already broken. The washer wont wash the clothes, just sit in the water and wont spin. I called Maytag, they offered me a warranty for another year for $371. The washer was only $550.00. When I tried to get set up with a repair service, the only company they used which was going to charge $105 just to look at it, would only take cash. When I called back to discuss with Maytag, they were no help at all. I was told they wouldnt even do the warranty since I scheduled a service even though I canceled it. I will never buy Maytag again.

Bought a Maytag dishwasher (Model #MDBH979SAM0) three years ago. Four weeks ago the control panel wouldnt work correctly. No matter what cycle I attempted to select, other cycle buttons lit up. The start button did not light and the cancel button would not turn off. I called a repair guy, he came out and said Maytag was having a lot of problems with the control panels. He reset the machine and finally got it working again. He said he wasnt able to get a new control panel from Maytag due to demand/delay in manufacturing. Today the control panel went out again. Based on all the other reviews Im not sure its feasible to put more money in this machine. Ill research other dishwashers and get one that has a better performance record. DO NOT BUY A MAYTAG.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

I recently purchased a new Maytag Commercial top loading Bravos from Lowes. It looked like a sturdy model and has a 10-year parts warranty and to cover this washer even more... I purchased the additional warranty from the factory. The washer is delivered, set up... First batch of laundry the washer is making all kinds of noise, the clothes are wet..water didnt dissolve soap packet... Repairman comes out..washer out of balance, cold water not at full pressure... Computer failure noted. Now still making a lot of noise, my clothes are twisted and intertwined and still dirty. My dryer isnt even taking the wrinkles out and even after I iron on hi steam the clothes are still wrinkled beyond belief... Im so dissatisfied with the washer... I want to return it... I cant believe Maytag would manufacture a washer that is ruining my clothes...

I called customer service to ask if there was some way that Maytag could assist me with repair of this like new dishwasher. When I said it was out of warranty and I had no additional warranty, I was told that a repairman could come out for $110 and diagnose the problem and that parts and labor would be extra. I explained that I had purchased Maytag because I saw commercials, for years, showing that Maytag repairmen had no work. She was very unhelpful and kept droning the same mantra, that a repairman could come out for the above charge. I was very angry and asked for the name and address of the President of Maytag so I could send a letter of complaint. I composed a letter, however: it is Thanksgiving time and I need my dishwasher so I made an appointment to have it repaired. I was told he would be out Mon. between 8 and 5. I asked for a more specific time and was told that I would get a call on Sat. with the time. Thankfully, no call came, because on Sunday, I read the reviews on this site and realized that Maytag was no longer a reliable nor a responsible company and I decided to save myself money and time and stress and just go out and buy a GE. So we will hand wash the dishes on Thanksgiving and buy a GE on Black Friday. This does not mean that I am letting Maytag off the hook. I intend to send my letter to Jeff Fettig at Maytag and also join in the class action suit. How very sad that the name Maytag has become just a name used to shill for defective and shoddy merchandise.

Purchased a new Maytag washer from a local Hardware store chain. Waited 3 days for delivery. Old washer was hauled away. Started using new Maytag Centurion the same night it was received. There was a funny odor coming from the washer that was discounted as new equipment smell. Saturday the Maytag Centurion washer was leaking some odd lubricant that had the same odor as the mentioned new equipment smell. Since this lube had been leaking out in close proximity as the liquid detergent my wife used a towel to clean it up. This towel went into the laundry with other clothes.Now Im concerned that whatever this oily stuff is, it’s in all of the clothing that was washed with the towel. Since I live on the West Coast and Maytag only answers the phone during the week Eastern Daylight Time I will call (2 days) after the fact. You might do well by finding out what this lube stuff is before you take it home and how youll have to deal with it once it leaks.

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

I purchased my Maytag side by side Model No. MSB27C2XAM00 in August of 2013. Within a 2 Weeks the lettering was gone on the control panel for the ice and water dispenser. I contacted Maytag and they replaced it, but the next one did the same thing, and the next one! They replaced it three times and they have all done the same thing. Now they are refusing to do anything more because they say I must be using cleaner or something on the panel because I am the only one having an issue with this! I assure you I have not used any cleaner and there are only three people in my household so it doesnt even experience excessive usage! I know this problem isnt as extreme as some, but when you pay this much money for an appliance you would like to think it should last longer than this!

On 12/09/12, I purchased a Maytag washer, model mvwc200xw, from our local Menards store. About 6 months ago, the washer started making a slight banging noise, and would occasionally move in the spin cycle. Now, when washing a small to medium size load, the banging noise is very loud and does a lot of moving. I found nothing in the troubleshooting guide to help me on this, so I looked on-line and found several websites discussing this same problem. They stated that the problem was a snubber assembly and the replacement part would cost $4.55. They also said the washer would have to be taken apart to change out this $4.55 part.I watched a you-tube video of someone changing this part and quickly came to the conclusion that I would need help in doing this. A comment was left in the video from a Maytag repairman saying that the person changing this part was not doing it in a safe manner. The repairman stated that changing it in the way this person described in the video was DANGEROUS! I wrote an email to Maytag customer service explaining the problem and asked if there was anything they could do to help me on this 1 1/2 year old washer. I received an immediate email stating they would get back to me in 3 days. Ten days later, I finally received a reply. I was told there was nothing they could or would do even though I was a valued customer and that they understand and appreciate my feelings of disappointment.I worked for a large department store from 1970 to 1990 and sold appliances, one of them being the Maytag brand. At that time, they were considered to be a top of the line brand. This was why I purchased Maytag appliances for over 40 years. I am surprised and saddened to see a lot of on-line complaints against Maytag appliances and also that this 1 1/2 year washer needs to be repaired so soon. Obviously, times have changed. I figured it would cost me at least $100.00 to have this washer repaired. Rather than do that, I am going to take this in need of repair to a scrape recycling center and then go out and buy a new washer, but it will not be Maytag! Maytag will never disappoint me again!

Contacted their customer service by phone and email numerous times...sent photos. They did nothing on a major issue,,three year old washer..now junk. Side of washer is rusting out the metal housing on washer is compromised.

I am writing this because I received an offer for a protection plan today in the mail. I purchased a Maytag dishwasher on from Home Depot. I had to have the control panel (motherboard) replaced a month after purchase to failed again approx. a year later. I still own this dishwasher (MDB7749SBB) but only used it off and on 2 of the first 10 year - have not used since. Well kids are in college and my next purchase will not be a Maytag. The wife and I lost all confidence in this product.

I purchased my Bravos washer and dryer in Sept. 2010. What a mistake! The dryer is okay but the washer is a nightmare! The repairman and I are on a first name basis. The last time he was here, he showed me how to recalibrate my washing machine. It stops working in the wash cycle, fills with water and then sits there. I have to manually drain it and start over. Then it gets confused and fills with water when it is supposed to be spinning and draining (consequently draining my well). I shouldnt have to recalibrate anything in life, much less, a brand new washing machine.

I wrecked on a bike, had surgery and in a wheelchair. I bought and had a Maytag dishwasher delivered from Beaumont Home Depot and this mdb7749sbw2 model never never worked. Home Depot told me I had to bring it back myself (Im in a wheelchair at the months that was impossible) and I called Maytag warranty. They sent a tech. He replaced a front power panel that didnt work. They sent out two more techs and they said use other soap Lemi Shine and the other guy said use Finish and turn your hot water heater all the way up. That never worked either. I have had this a yr and it just sit there and money in the trash. It makes me sick.

We bought the Maytag Bravos Washer and Dryer set in 2013 after extensive reviews as well as the brand recognition to replace my at least 20 year old Kenmore washer/dryer. At first we were very pleased. The ability to do bulky loads was great and the high spin cycle left the clothes almost dry. In 2018 (keep in mind, just 5 years!) we started to hear a grinding sound in the washer when on rinse cycle and the dryer would randomly turn itself on! Strange but true. I called Maytag Canada and they sent someone right away. They had to replace the motherboard on both the washer and dryer as well as the drum and gears on the washer. Fortunately this was covered under warranty.Fast forward 1.5 years. Same issues with washer...technician came and could not identify the problem, although I did tell him it was the same as 1.5 years ago. I ended up recording the sound and asked them to resend technician to the house. After further diagnostics, yup...same problem. Two days went by and I received a call back advising me that the cost to repair would be over 700.00, not covered by warranty! I escalated to management, to no avail although they did offer me 15% off my next Maytag purchase! Needless to say I have ordered a brand new GE from Costco, arriving tomorrow for basically the same price to repair the Maytag. I will NEVER purchase another Maytag product and will advise anyone who cares to listen to me to do the same. Huge disappointment in the Maytag product, brand name and customer service. 10 year warranty? Not likely...stay away.

Centennial commercial tech. washer - We purchased this piece of junk in Sept 2013, and had to have a repairman twice before it was six weeks in my home. I wrote several letters but the only thing that I received were applications for insurance to cover repairs. I should have received a replacement as it was bad from day one, but Maytag doesnt replace!!! Its been semi-reliable for the past several months, until early this year. It started jerking when it changed cycles, sounding as if the drum was hitting really hard against the sides. It has continued to do that regularly; now it wont function on the cycle its set on. It wont spin, sometimes the lid lock wont work. It starts filling when it should be draining. This evening, it stayed in the rinse cycle for 40 minutes and when I realized it was still rinsing I had to unplug it to get it stopped. It goes on and on, (and so could I out of frustration). The good name of Maytag has turned to trash, and when it leaves my home, no more Maytags!!! PS. The dryer we got with it takes at least 1 1/2 full cycles to dry a load, and since I couldnt get it to spin properly, Ill be lucky to get this last load dry in 2 to 2 1/2 cycles.

The Maytag Bravos washing machine may well be the worst appliance available for purchase. Sure it is a high efficiency machine that saves on water -- the clothes are often still dry when the complete cycle is finished. Many times there is still soap residue on the clothes. Forget cleaning anything with any amount of dirt on it because it seems as though items are even more filthy after washing them. I have tried everything the company advised and still my clothes are not clean. My advice... please do not purchase this machine. You would be better off taking your clothes to a river and beating them on a rock. #wearingdirtyclothesforever

My washing machine is a Maytag Ive been using for over 27 yrs. I love the older, top loading machines because I like to take certain items out after 5 or less minutes. I now live in an apartment & wont use their machines! Thinking about a stackable for my personal use. I am quite fanatic about laundry & do a lot of items by hand.

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

My oven looks like it has never been cleaned. The self clean Aqualift does not work to clean your oven. If I would have known that this feature did not work for self cleaning I would never have purchased this oven. My old cheaper oven at least came clean on the self clean cycle. Now it seems I am going to have to scrub my self cleaning oven. What a waste of money. Will never purchase another Maytag appliance.

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

In 2003, I purchased a brand new Maytag washer and dryer set, I chose Maytag because of their reputation. Within the first 6 months, I had a bearing go bad on it and that had to be fixed. It has become noisier and noisier throughout the years and now it is leaking all over the floor when I do a load. I am single, I live alone, I do laundry very seldom and do not do large loads. I am so disappointed with Maytag. When the repairman came out initially to fix it, he said that the brand he fixes most often is Maytag. Expensive lesson learned, Ill never buy any type of Maytag product again.

I just saw that there had been a class action lawsuit settled in 2005 for the Maytag Neptune front load washer and I was never notified as an owner! I have this crummy product and have been living with it for more than 10 years! I just scheduled a repairman to replace the moldy gasket (for the second time) and the noisy pump, and a latch that has to be slammed for a sum of $438. What a crock. I was told this was a top of the line model when I purchased it for $999. Ive never had such a piece of junk before in my life. I run loads of bleach weekly to control the mildew.

I have bought Maytag products for years. I have a white Maytag microwave that is about 3 years old. It was given to me at 1 yr. old by my sister-in-law when she decided to splurge and create her dream kitchen and went with stainless. The door handle broke in the first year. We glued it. It just recently completely fell off completely-snapping at both ends. I am calling Maytag and attempting to have it repaired. I am otherwise very pleased with this appliance. I have had other microwaves for many years without this happening. Im hoping they will agree to repair.

Purchased Maytag dishwasher Model Number MDB7749AWM1 in June 2011. With a two person household, we need a new control panel in Sept 2014. Total cost of service call, repair and part is $325. This unit was a poor value for us. I see the trend is to discontinue a model after a short period of time, making it impossible for anyone to get a review of other peoples experiences. I went with Maytag because of this. It was a company with a strong reputation for quality equipment. Not so anymore. I would not purchase another product made by Maytag.

We purchased the Bravos XL in May 2017.. It quit working on April 30, 2019. Maytag sent me a form letter that basically said I was out of luck.. that sometimes things go wrong with a product or manufacturing. The fact that it wasnt 2 years old yet meant nothing to them. I would like to join or start a class action. This washer should not be sold.

I have had this washer for a few years now and it is the WORST machine ever. It never gets clothes fully clean as air gets trapped in some items so they stick out above the water. The drum only fills about 1/4 of the way no matter what you are washing. It is always unleveling and you have to constantly re-arrange bed sheets and larger items. I have to first soak larger items before the wash cycle. Nice HE machine. When I purchased this machine the sales person said you can wash 10 bath towels. I read the directions which said make small piles of clothes and I called and told her that after I had purchased the machine. Her reply was oh, I didnt know that. Obviously. This top loader without the agitator cleans great if you only throw in about 10 thong underwear at a time or two pair of jeans.

I purchased a topload washer two years ago and the plastic lid has been replaced 4 times because it cracks at the hinges. It is obviously a manufacturers defect that Maytag refuses to admit. They come up with excuses blaming the consumer instead of their bad design.

Bought a Maytag Washer, in 2010 the Bravo. Good looking washer and dryer. I bought a 4 yr warranty for both. My washer has needed service every yr of the warranty, leaks and has stopped running. Now it is out of warranty and it is leaking again. Was just fixed a little over a year ago. I am now seeing a lot of rust around the top of the washer. It has just about covered the one port where you put the bleach in. The seam around the top in the crease is full of rust. My dryer is fine, bought them both at the same time. I have never seen this on a washer before. My mom has had her Maytag for yrs no problem. I bought these thinking they would last, boy was I wrong.

We purchased a wall oven model MEW7530DE 11/8/2014 which was installed the first part of December 2014. From the beginning the temp was not constant and everything baked was either burned or under baked. The first repairman said the control panel was faulty and was replaced four months after purchase, the problem continued. After three more repairmen all from different companies concluded they could find no problem and thats just how ovens work now. We contacted the owner of Hamiltons Appliance, where the oven was purchased, and requested a replacement oven which was accomplished December 2015.New oven, same problem, very disappointing. My wife has been baking for over 50 years and has never experienced problems and frustration on this level. The condition of the oven is totally unacceptable and with all the effort by us and others we are at a loss. We purchased an extended warranty which has resulted not fixing of the problem. We hired an electrician to inspect the wiring in case that was the problem, costing us $200. The wiring was all good. What do we do next and what are our options short of another new oven. WHAT IS MAYTAGS RESPONSIBILITY? Respectfully, a very unhappy customer.

I purchased a Maytag gas range in the past few weeks with Aqua Lift Cleaning System. I have only cooked once when grease spattered on the walls and floor of the oven. I have used the Aqua Lift Cleaning System 5 (five!) times and the grease is still there and very sticky. This system clearly does not do what it was supposed to do. I was fortunate to have bought the appliance where I could return it; however, it has been quite a hassle and I will have to pay an additional $100 to have the old one removed and the new one installed! I feel like Maytag should reimburse me the $100 because it is obvious to me now that I have found hundreds of reports of people not being satisfied with this feature.

Maytag top load washer. I dont understand why Maytag would make such a piece of crap. It takes so long to wash, that I can only wash a couple of loads a day. It doesnt fill. It doesnt get the clothes clean. My electric bill is higher. Its so noisy too. Never thought Maytag would make such garbage.

I purchased this machine (Maytag Bravos XL MVWX700XL2 ) about 18 months ago. I was so excited with the looks and the reviews I found on the machine at that time. For the first 14 months I was happy. All of a sudden, it has become the washer from Hades! It twists and almost ruins my clothing. Not to mention, I think it is permanent wrinkles that it puts into things. I washed our comforter on Bulky. The part that must have been at the bottom is completely wrinkled and it also wrecked all of the fill. This was a comforter that it is supposed to be fine to put in the washer. I am attaching pictures in which you can almost plainly see where the comforter was at the bottom. I had a serviceman out a few weeks ago. He said Maytag knows that there is a problem, however, there is no service bulletin that is out yet on it. In addition, he ran all of the codes and told me there is nothing wrong with my machine. That must be why I have to iron almost every piece of clothing in this house. Maytag will hopefully give me decent customer service on this, or I will come unglued. For the price of this washing machine, I expected much more.

Stove does not heat evenly in oven. Electric burner cannot be turned down to low or simmer, then it will not cook at all. Other burner turned down to low does not stop bubbling and stays at a high temp. There is no consistency. I am extremely disappointed and curse at this stove every day. Model #MER7664XB. Serial #R13316302.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

We paid over $800 (more with installation) for this quality dishwasher. Within one year we began to experience problems with this unit. The top control panel easily becomes water logged causing the device to fail.

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

Maytag is a product that I would buy any time. Even uses it well last for a long time. If you want to spend money this is a good investment for your kitchen and as for your laundry get the washer and dryer. You do get your moneys worth with Maytag.

My husband and I purchased the Maytag dishwasher model #MDB7609AWW2 in December 2010. July 2012, the control panel would not operate. I called Sears to schedule a repair appointment. (I did not have an extended warranty.) After reading review after review of complaints about Maytag and control panel issues and learning it is a very costly repair, I called Whirlpool which now owns Maytag. (Be advised, Maytag is not the quality product it once was). Reviews also indicate that the replaced control panels are failing within 6 months to a year and a half. After talking to a person in the Maytag/Whirlpool service department, he suggested some things to do: unplug power, unlock control panel, etc. He determined it was most likely the control panel that needed to be replaced. I asked how long a new panel would last informing him of the complaints Id read. All he would tell me was that I had the option to buy an extended warranty. We have decided not repair the dishwasher and will replace it with a non-Maytag and non-Whirlpool brand. I will never buy Maytag or any products made by Whirlpool again. For a major component of the dishwasher to last only a year and a half is unconscionable.

I bought this washer from Lowes in 2013. It worked okay for a little while but lately it stops mid-cycle. Clothes are soaked and all of the soap hasnt been rinsed out. Poor excuse for a washing machine! Will never buy a Maytag again!

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

We have already replaced the motherboard and now it is throwing a code of and it takes a whole day to keep pressing start to get one load down. I hate these machines and tell everyone NOT to buy one. They are expensive to buy and too much trouble to fix or repair and too much money to fix. BUYER BEWARE!!!!

Maytag Bravos Series 300 - I bought this machine less than a year ago. There is an awful smell coming from the machine that I never smelled from any other washer I have owned. The clothes do not look, feel or smell clean, and my towels are ripped. It is an extra large washer, yet when blankets are put in the machine bounces and shifts. After reading all the reviews, it seems I am not alone in my concern with a machine that was not only expensive, but was told it is a great product. Maytag needs to do the right thing and recall this machine.

Maytag washing machine is the loudest machine Ive ever heard. It doesnt wash the clothes well leaves spots. We had a new barrel put in and it still walks across the floor. The water level doesnt come up high enough, makes grinding noises and it takes forever for the wash to be done. How can you say its an energy saver if it goes on for an hour or so. Very dissatisfied and pissed off.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

We bought a Maytag refrigerator about 3 years and have had so much trouble. The freezer section which is on the bottom half leaks water periodically on the floor unless, we take the bottom rack out and pry the ice from the shelf about every week. It started doing this about 6 months ago and well need to get a repair man out here. The doors on the refrigerator are also a problem. They often dont close properly, so one is partially open, but unless you look directly at it, it isnt noticeable.

We have had a Maytag Bravos XL top load washer less than a year. Big Mistake. It was JUNKYARD ready when it came out of the box. Does NOT wash clean. Weve tried everything.The agitator looks and acts like a toy. Will not run enough water to wash anything. We had a LG front load before and its hard to get use to having dirty clothes. NEVER AGAIN.

I purchased one of the first Impeller washer and dryer. The dryer is great, but the washer needed repair immediately. Home Depot refused to exchange the pair, so I will never buy from them again. The washer takes over an hour to complete the wash cycle, has to be set on Bulk in order to get enough water for a decent wash, and is extremely rough on clothing. Its made holes in some of my shirts and everything comes out twisted without enough rinsing. Sleeves are always turned inside out. Thats how rough it is. It costs me more in water and electricity. Neither Home Depot nor Maytag would replace the pair for me.

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

Maytag Bravos quiet series 300 - We have had this washing machine for approx. 2 years and there is rust marking around the opening of the spout where the bleach is poured into. We also find that we have to do the clean cycle quite often. And it bounces and make a loud noise if there is not enough clothing in it… even on the bulky cycle. I WOULD NOT RECOMMEND THIS PRODUCT TO ANYONE! And we have been loyal purchasers for 40 plus years!

I called Sears to have a simple repair done to my Neptune washer and received a quote for $800.00++. They gave us a coupon to get a new washer at Sears and we did. Last week my dryer broke and I looked the repair up on Youtube. It looked real simple. A quote for $270 was given to us. Again a coupon if we wanted to buy new. It seems to me Sears jacks the price up on its parts and labor in order to push the customer to buy new. So far its worked for them and Im sure everyone else as well. Its not going to work out for Sears this time. Im no longer doing business with them and I will do the repair myself. I still got stuck with the service call but that will end as well going forward because I know now what the game is. Shame on you Sears. Double thumbs down for my Maytag Neptune washer and dryers.

I have Control Panel issues with my Maytag Quiet Series 300 Dishwasher. I have saved myself hundreds of dollars! The problem occurs when oxidation or steam shorts out the ribbon on the control board. Simply shut off the power to your dishwasher. Open the 5 or 12 screws on the door. Open the black box where the Control Panel ribbon enters the Control Board, slide the white tension clasp away from ribbon and clean off ribbon using a paper towel. Re-insert ribbon and slide tensioner in place. Replace all parts and turn on power. Job done! I hope you have as much success as I did.

I’m 41 years old and finally had my first new washing machine. Four days later, while my 11 year old had the stomach flu, it died. Not impressed. Apparently the delivery guys left a note on our file saying there was a defect on our washer and that we needed to contact Maytag. This was news to us when we called The Brick today. I hope they didn’t knowingly sell us a defective washer. Alas, we have to wait until Monday with pukey sheets in the washer.

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

I have now owned my highly efficient and low-cost to operate washing machine for 6 years. It is a top loader and uses HC detergents.This means the washer needs minimal soap to clean the clothes. I especially appreciate the different types of loads such as deep cleaning or regular cleaning. The washer has sensors that evaluate the size of the load and thus only utilize the amount of water necessary. I really like the quietness and being able to get the very best wash because the washer does exactly what it needs to do. It has more than been the appliance that I had hoped for. Love it! It maintains itself.

I would like Maytag to repair or replace this dishwasher. It has only been installed since November 2014. The only button that works is the auto clean. None of the buttons work. I thought Maytag was a reputable business.

We are an extra-large family, and required an extra-large washing machine to handle our needs efficiently. We thought paying quite a bit more for the reliable Maytag brand name would be a good investment and worth it over the years... HA!!!! The Bravos XL model has turned out to be a major disappointment! It gives no manual control over the water level and you can actually have things come out of a load dry! The loads continually become unbalanced. Clothing is continually damaged - rips, tears, shreds. Wrinkles everything... even jeans?! Even with proper amount of detergent use and frequent affresh tab cleanings, the clean washer reminder light repeatedly comes on. It leaks from the bottom, although we cannot determine why or exactly where the leak is originating! It is a seriously frustrating, substandard product, and I cannot believe Maytag (and Sears, where we bought it) is continuing to sell this machine (and may I add at a crazy high price)! Both of these companies should be ashamed of themselves for peddling such poor quality washers and leaving their customers so dissatisfied! Stay clear of the Bravos XL!

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

Fridge Model MFF2258VEB6 - Our refrigerator is less that 2 years old and it wont make ice! The bottom of freezer is filled with water that froze. Everyday there is water on the floor. We asked at Home Depot where we purchased it and they said we need to change the filter. What filter? The owners manual is a joke. We cant figure out where the filter is located so it looks like we have to pay money to have someone come look at this. Hey, this is ridiculous. I thought Maytag had a good reputation and thats why we bought ALL Maytag appliances two years ago! Never again!

WARNING FIRE/HEALTH HAZARD - BRAVOS MVWX500XW1. Purchased it new 2011. Never cleaned well. Some clothes came out with dry spots, darks had soap scum/lint spots over them. On several occasions, clothes were not wrung out properly. BUT when I went to do a load of laundry recently, I heard a loud POP and almost instantly my entire basement filled with an acrid, dense grey smoke coming from under the machine. I am concerned toxic chemicals were released. People still smell the odor in the house. Need to get in touch with company again after the weekend to see what they will suggest.

We bought a Maytag Dishwasher - Model #MDB4949SHW a year and a half ago at a Home Depot Location. We had previously had a Whirlpool dishwasher for 13 years of heavy use, with no issues or difficulties. At the time we purchased our dishwasher, there were various different brands on sale, including the one we purchased. The sales rep at Home Depot advised us that although we could get a similar dishwasher for the same price, that this particular model had a 10 year warranty. When I heard that, all I heard was 10 worry free years. MY MISTAKE. I could never have imagined that a company such as Whirlpool would advertise a warranty, that in the end is made up of nothing but false advertising.We ran a cycle during the Christmas holidays, and detected a funny smell of burnt rubber but didnt know what to make of it. I googled the issue and some people had had experiences with perhaps a plastic utensil or some other plastic, being burned by the heating element, so I figured that its what might have happened. I ran another cycle the next day, and the smell was much less prominent so I thought the problem had gone away. The next time we ran a cycle, the water didnt drain. We called in a repair person, and was shocked to learn that both the drain pump and main control board needed replacing.We got in touch with Whirlpool and low and behold, the only items they cover are nonsense items such as the racks, drum, tub...etc....in other words, the parts that are actually responsible for the running of the machine, are not covered, neither is LABOUR. Therefore, in my opinion, their warranty is trash and should not be relied upon under any circumstances. We purchased a new dishwasher just a year and a half ago, and are left with a heap of junk in our kitchen. Our options? Either spend $600.00 to $700.00 on repairs, possibly more, or buy a new dishwasher. When I asked if there was anything they could do to at least mitigate my damages, I was told....Sorry for your inconvenience...but do you have any other questions. I dont have any other questions...but I do have have a comment.... Make your products better....and dont print warranties that are utterly rubbish, false, and only serve to mislead the consumer. Needless to say, we will not be buying any more appliances from this company. Their one and only goal is profit for their shareholders with no regard whatsoever for the consumer. If I could give it ZERO stars, I most certainly would. :)

Ive tried all manner of washing clothes, especially dark ones. Different cycles, different detergents and amounts, but it always leaves scum marks in folded places. I have to either brush off what I can, and/or rinse the clothing in a sink and then rewash the clothing without detergent. In an attempt to save water, I end up using two or three times the amount.

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

Our new refrigerator was pissing all over the kitchen floor. We had to disconnect the ice maker after an alleged repair part was supplied. (We had to pay a plumber to install it.) It didnt work, so we finally had to disconnect all the parts related to the ice maker. Here it is July, and ice cubes would really be appreciated right now. I get angry when I see all the Maytag commercials that pop up on the internet!