Wow, I bought a Maytag Bravo 300 series washer and dryer three years ago. They have been a complete piece of crap. I spent nearly $2k on the set at Home Depot. During that time, they have been serviced four times and I am now out of warranty and the washer is constantly breaking with LD and F51 errors. The heavy dryer door with light as hell hinges fell off on my wifes foot when she was loading it. I cannot get it back on. It is rigged so it will work. I contacted Maytag and they were not helpful at all. Pretty much sorry about your luck. I will never buy another Maytag product again. I agree with other posters. Too bad you cant chose zero stars!

We bought new appliances when we moved to our new house last June (2016). Sears recommended the Maytag 600S pair (HE washer and dryer). We have contacted Sears numerous time to have service people out because many times (75%) the washer does not fill with enough water to wet all the clothes and there is a layer of dry clothes at the top when the wash cycle ends.I do not believe that dry clothes get clean because they are near wet clothes in the washer. But Sears insists this is by design. Some service people tell us that the top loading HE washer will be gone soon because of the complaints but we have to struggle on. Sears seems to hope we just get tired and stop calling as their Customer Service policy. I have to dump 1-2 buckets of water into almost every wash that we do. As a side note, the 600S series has a slanted top rather than the traditional flat top. It looks cute but things fall/roll off of it. It would be nice to put things on top of the washer or dryer while doing the laundry but they roll/slide/fall off. The design is not so cute anymore. Actually, really a stupid idea.

We purchased a Maytag Gas range MGR8674AB in November 2012. The contents of the drawer (oven mitts, trivets, hot pads) caught on fire. As we pulled out the drawer, it scorched the front of the range.

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

I have had 2 Maytag washers in 37 yrs and loved their products, however I purchased a Maytag quiet 300 in 2/09 and it is the worse Maytag product on the market. The frame around the bleach dispenser has rusted out and I have called for the 3rd time in 5 years to have it repaired. To my dismay it will cost 300.00 to fix because the bearings have to be replaced. I will now have to purchase a new washer. The days of the Maytag man are long gone. By the way the Maytag dryer has been serviced twice. I thank God everyday for that extended warranty I bought, but now it has now expired.

We purchased a Maytag Bravos set in 2011. The dryer works great, but the washer not so much. Every load of darks comes out with soap scum all over. I use the HE detergent and most time use less than what the load should have. We have soft water and I also use softener. Ive also tried up to 3 extra rinse cycles and a smaller load size and still have soap scum all over. Im sure the light colored loads come out same, just cant see it. Needless to say, very, very upset with this washer. I, too, will never buy another Maytag product, nor will I recommend one. Had our yearly maintenance check the other day and the service man couldnt give me the reason its doing this. So, so disappointed in this product!!

This machine may save water but I spend more time and money getting out the severe wrinkles it creates. I use my dryer and iron much more than with my previous washer. I never thought a new washer would make wash day more difficult.

I like the full width drawer for large items. Our Maytag refrigerator is 12 years old and just beginning to make noises and get too cold. The little plastic features for setting the temp and humidity on the produce doors were the first to break. Water is inside door which is not as convenient.

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

All of my brand new white wash cloths have black stains on them. They look like mechanics use them to check the oil. And, my white denim capri pants have weird stains on them. This washing machine is a joke. It may be water efficient, but sacrifices cleanliness and stain removal. Maytag should recall this ** Queen.

I purchased a Maytag washer and dryer three years ago. They both were taken to recycling and I received eleven dollars for both of them. They were both horrible. The transmission went out on the washer. The repairman said not worth fixing since it would cost $600.00 to repair. He said Maytag appliances are being outsourced and are not what they used to be. Even before the transmission went out it took forever to wash and the clothes smelled when I took them out of the washer. The dryer quit heating a few days after the washer went out. The repairman said it wouldnt be worth repairing it either. I will never buy another Maytag!!

Maytag Neptune Stacked Electric Washer & Dryer. Had to buy a motor for Washer but lasted 12 years before giving problems again; then couldnt find anyone that would service for cheaper than $100 for just coming to your house plus $75 an hour for labor. Thats HIGHER than my billable rate! Rip-off Service & parts charges. Found out it was easier & cheaper to troubleshoot ONLINE myself using FIXYA site and others. Expense for an appliance above what most run ~ 1500 for both units. Plus if it doesnt have or offer a 5-year warranty then something is wrong with the quality! Maytag Neptune Series MLE2000AYW 27 Inch Electric Laundry Center with 3.34 Cu. Ft. Washer Capacity, 4 Wash Cycles and 6.0 Cu. Ft. Dryer Capacity, 3 Dry Cycles: White. Worst part on this model was a WAX MOTOR that they used for the Washer to control the door being closed or open. Next worst DESIGN error was they didnt put a drain hole in the plastic rim seal for the Washer door, that area would build up mold & mildew if you didnt learn to keep Washer door open at all times AFTER a wash. We learned by removing the light bulb! Therefore it was easy for my crew to learn to leave the door open after washing. This model was Energy star certified and had a long life here 12 years. Unfortunately I think they build these things to only last 10 years; then you have to replace them. In years gone by... the 1970s Washing machines and dryers would last 20 years!!

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

How is this fair that only a couple of washers recalled...I knew of no recalls either...My old Kenmore top loader outdated by far. Guess I should have kept it.

On my 3rd circuit board for a MDB7749SBMO MODEL dish washer. The people at Maytag are people that wont even talk to you about it. How many people have to complain before theres a recall on a faulty ribbon cable.

Had the new set for over a month now and are very impressed. If you actually know how to do laundry, and dont load it up to the top with greasy, dirt filled work clothes, etc. (like some **) you will have no problem lol. We have Absolutely nothing bad to say about Maytag products, and the new set is amazing!!!!

I wish I had read these reviews before purchasing my dishwasher. I have used it 40 times max. The control board went out. They want 307.00 to fix it. Really? Why would I fix this piece of crap when I can buy a cheap one for that price that would work better. Ridiculous! I paid good money for this dishwasher and the warranty that comes with this is a joke. Save your money and brand from a company that stands behind their product.

I have had this washer (Maytag Bravos) less than a year and it does not clean my familys clothes at all. I have had to throw away clothes that are stained and ruined because this washer does such a poor job of washing. For the cost of this appliance, I thought it would do an excellent job, only to be disappointed. I have owned other Maytag appliances without a problem. This one is a disaster and has turned me against Maytag.

We purchased a Maytag Dishwasher Model #MDBTT60AWW3. Shortly after manufacturer warranty ran out, the control panel went out. Luckily we had purchased the extended warranty. The repair company came out and put a new control panel in it. Two months later, the control panel goes out again. The warranty firm sends out a different repair company. They replace the control panel again. This time it doesnt work. They replace some of the buttons as according to the repair person they arent registering the correct OHM reading. It works again. Yay!. A week later, its not working again. The repair company is coming back. This is really starting to get old. Between the multiple times it has broken down, waiting for the repair company to come out, diagnose the problem and order parts, we have been without a dishwasher for approx. 2 months the multiple times it has broken down. Im so fed up with this thing. I also will never ever buy another Maytag again. They need to have a major recall on these because of the terrible, terrible control panel. This isnt just me, its a lot of people.

Maytag refrigerator - After 3 months, a water line broke and caused $350 in damages to our kitchen floor. The next month, the ice maker jammed. The next month, the ice maker went out. I have agreed to let the Maytag repairman (youve seen the commercial where he never has anything to do) use our spare bedroom. Seriously its the worst appliance, by far, Ive ever owned and Ive had plenty as I am 71 years old.

Im extremely disappointed in this machine. I bought this machine after having my Kitchen Aid for 12 yrs. Just last month, the UL message came on. Had someone looked at it and noticed the bearing was loose. He fixed it, just today, it started doing the same thing again!!!!! Now it might be a suspension problem. Of course my warranty expired because I bought it in November 2012. Im never ever going to buy a Maytag washer again!!! Can someone help me to take my complaint to higher up?Thank you..

Maytag Gemini - This is a double oven which I purchased in 2010. 2 days ago Apr 13, 2015, the outside glass in the bottom oven simply exploded. The oven was in use at the time. It blew the side brackets off and glass was spread into my dining room as well as a mess in the kitchen. Maytag was supposed to send repairman today. Have waited all day and finally called repair company. They knew nothing of the repair and supposedly will contact Maytag and call me tomorrow. We will see. In the meantime has anyone else had this problem?

Every 3 months, the freezer compartment needs to be dismantled to unclog the defrost drain hole. When this occurs, it dumps all the defrost all over the base of the freezer which then leaks water out of the freezer door all over the floor. Clearly a design flaw and Maytag will not acknowledge this but appliance repairman says these are notorious for this. A $1700 fridge shouldnt do this. Never will I buy a Maytag again, a complete POS.

Ive had my Maytag refrigerator for 19 years and it still performs well. I keep it clean both inside and underneath. The lighting is one aspect I really appreciate as there are two bulbs in the interior so theres never a problem seeing all the contents. Also appreciated are the movable shelves on the door and the ability to raise or lower the main shelves in the body of the fridge.

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

We had a Fisher & Paykel Washer that lasted 14 years. This Maytag Bravos XL washer has been the worst machine I have ever owned. The clothes come out dirtier than ever. In todays world all technology is becoming disposable, Where is the Maytag repairman now? I have tried all of the settings, to have a decent wash. I am ready to throw this out. Lowes you need to do something about this. It may be made in America but now we know why Japanese and Korean electronics just work! Damaged Clothes/Clothes not being washed thoroughly enough are my biggest pet peeves with this washing machine.

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

Horrific, useless, inconsiderate, rude, discourteous, arrogant and banal! I bought a brand new washer and dryer. The dryer is steam type and defective and they will not exchange, despite never being used. Nowhere am I committed to an agreement saying that the machine will not be replaced if it is defective. I am getting the run-around from the store, the manufacturer and the service technicians that didnt even arrive with tools when they came to evaluate the problem. If I had my way, I would return the washer and dryer and change manufacturers. But it is a stacking unit and I used the washer which commits me to it! Maytag, Whirlpool, JennAir and KitchenAid are all the same company. I am running out of options except going to the European manufacturers! Miele will at least install the appliances. They will be my next machines and I will not have to pay a plumber twice to install them the next time!

CONSUMER BEWARE: Maytag is the WORST corporation to deal with. We have purchased a Maytag range from them recently. Unfortunately we have had 4 appliances delivered to us damaged from Maytag. The fourth time around we finally got a supervisor on the line. In order to expedite the situation. And the supervisor (Frank) refused to expedite or even call to try and move up the 5th delivery date. All he talked about was Maytag company policies to us. To make a long story short and I do mean long. Buyers beware. Maytag DOES NOT HOLD THEMSELVES ACCOUNTABLE FOR ANYTHING. Once the appliance leaves their facility they are not responsible for it. I CANT SAY THIS ENOUGH. DONT PURCHASE MAYTAG PRODUCTS.

I have had this refrigerator for a few years and never have had a problem. It keeps food uniformly cold, and is frost free. While appearance is attractive, it doesnt look like a $3,000 refrigerator. However, black pebbled-surface exterior is easy to clean and scratch-resistant. Plastic and glass interior fittings also have held up very well. I originally thought it would be too small because I was buying it to fit a certain space in the kitchen. But it has turned out to be just the right size because there is no wasted space inside. I bought this at Home Depot on sale for about $400.00 and it has turned out to be an excellent buy. Delivery was on time, efficient, and people were polite and helpful. Refrigerator was ready to be used about 15 minutes after delivery arrived. I have found Maytag appliances to be extremely reliable and made to last. They have never disappointed me. I will continue to buy them. I highly recommend it.

Home Depot is selling defective appliances manufactured by Whirlpool and refuses to provide a full refund. I purchased a Maytag washer and dryer from Home Depot in August of 2010.Washer broke in February of 2011. No parts available for repair, Whirlpool replaced washer after 4 weeks. This washer broke in July 2011. No parts are available for repair until August 17th.

Purchased a Maytag Bravos washer in 2009. Was told it was water efficient and electric efficient also. Spin cycle twisted my clothes in a knot and left white blotchy doors on my dark clothes, had to rewash my clothes again!!! Then started making a horrendous noise that could be heard from one end of the house to the other, like it was going to explode at any given time. Called technician, paid $75 and said it was bearings and that it would probably did the same noise again even with fixing it, that Id be wasting my money!! Worth getting rid of it!! I just hate it!! I will never buy another Maytag again.

I bought all new Maytag appliances for a new house built 2 years ago. The oven fan, while in warranty, began coming on in the middle of the night. It would turn on, cancel, began not working, and then the ticking noise began. Maytag sent 5 different service people out, sometimes without the part. We are afraid to use it now and have turned off the breaker for it. Now, it is turning itself back on again. Maytag says we must now pay for any repairs/service calls as it is out of warranty. It was not out of warranty when all these troubles began.I called Maytag customer service today and could not have talked to a less customer friendly person. She didnt care that it was in warranty when the trouble began. It is out now and is our problem. There is no one else but her we can talk to about it. She is the decision maker. What experiences has anyone had with trying to call the president of Whirlpool, or filing a small claims court action? Any help is appreciated. Who is going to cook our Thanksgiving turkey?

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.

I purchased the Bravos XL washer and dryer from Lowes in March of 2011. I had only had my dryer for a couple of months when it stopped drying out of nowhere. The repair man came and replaced the fuse assembly and all was well until December 2011. Again the same problem happened. I had to wait almost 10 days for someone to repair it. Once again in January 2012 for the second time the fuse assembly was replaced. Its now December 2014 and again my dryer has stopped working. Have to wait again 10 days for anyone to come and fix this. I will never buy another Maytag dryer again.

Bravo XL Washer & Dryer - I have owned this set for just over 90 days and have called Maytag several times just to get insulted. The customer service representative is not helpful at all, and tells me that I am not using HE detergent or that I am using too much HE detergent. Furthermore, they tell me that if a service technician comes to my home and nothing is wrong that I will get charged. So much for the extended warranty and what is wrote on the Maytag site. I explain each time that I am using name brand HE detergent and the recommended amount. The soap dispenser in the machine provides a fill line that I fill to. I have even tried using less detergent as recommended by the appliance store that I purchased the machine from, and still the washer does not clean my laundry and leaves residue on everything. I have even tried using the extra rinse, and extra heavy soil setting which does not make a difference at all.The other concern is that the clean washer feature light flashes weekly. I have purchased the cleaning tabs recommended to clean the machine, and run this clean cycle every time the light comes on. The dryer does not work all that well either and shuts off before the laundry is dry. Sometimes the dryer will show an error of airflow restriction or low airflow. This is confusing because the dryer vent and hose are clean, and the lint filter is also clean. This is so disappointing because I thought Maytag had great products. However, as I read other reviews about these machines and the customer service representatives it seems that there is a systemic problem with the machines and the customer service representatives that needs to be addressed by the leadership at Maytag.

This review is for a Maytag Gemini MGT8775XW 30 Freestanding Double-Oven Gas Range w/ 5 Burners. I cannot believe the amount of problems I have had from this $2000+ range. Within just a few weeks of getting it, the paint started scratching off the surfaces nearest the heat. Then, the plastic cover over the digital display and controls bubbled up due to the heat of the broiler being in use. They designed it so that the heat escapes from the oven right in front of the control panel, so when you want to adjust temperatures on the control panel, you chance getting burnt from the hot air every time.The very worst design are the manual knobs for the burners on the front. They are at an angle, and if you look at the oven straight on, you see they are higher than the burner surface. A hot pan that overhangs the burner cooks the knobs. The plastic interior of the knob lacks any kind of heat resistance and actually starts to turn soft, keeping you from being able to turn off the burner at all!Most dangerous of all, the knobs are frighteningly easy to bump, pouring gas into your house. We have had this problem multiple times. Today, my dog must have wanted to investigate the top of the stove, because when I came home, the burner was on, had burnt through a pot on the stove, and was just at the ignition point for an item sitting next to the stove. If I had come home 15 minutes later, my house would be in flames right now. I am having to air out my home as I type this. I am DONE with this dangerous oven and will be shopping for a new one, and it certainly wont be Maytag.

Maytag Top Loading Washer-We bought this machine a little over a year ago and it is one of the worst products weve ever purchased. More often than not clothes barely get wet and then wad up into a twisted mess which stops the machine. Ive had to restart a load over and over. And, the clothes are not as clean as they were from our former Maytag washer which lasted 14 years. The new washer has to be cleaned at least once a month or it smells. We purchased this washer from HHGregg and they are no longer in business or I would complain to them about selling faulty products. I dont know why the manufacturer decided to remove the agitator from new models. What a mistake! We have decided to get rid of this washer and buy another brand. No more Maytag (or Whirlpool) products... ever!

I purchased this Maytag Washer and Dryer back in 2000 and have never been unhappy. It really gets my clothes clean and uses a lot less water than a top loader. The only issue is that if you do not clean it once in a while it will start to smell, but I have a cleaner I use every month and so far (knock on wood) it doesnt smell mildewy.

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

I bought a Maytag washer expecting To get the best and have already had Service on it three times and it still isn’t working. I have spent a fortune at the Laundromat when I have a 4 month old washing machine at home and not getting anywhere with getting anything back on this. I am very disappointed in this Washing Machine.

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

After everything posted here why would anyone take a chance buying any Whirlpool product including all subsidiaries. I made the mistake of buying a Maytag washer and dryer less than 3 yrs ago. There are only 2 people in the household and we only wash linens, towels and undergarments- the rest goes for dry cleaning. The washer stopped filling with water, similar to what was posted by another customer. Maytag customer service was 2 weeks out.When the service tech arrived he diagnosed the problem as a faulty water value but didn’t have the part- another week. I asked the tech why it takes 2 weeks to get someone out for a service call- he told me that there were 4 techs working the area but 2 quit and they were never replaced. The tech went on to say that he was leaving because of the misdirected grief he gets from customers because “the Whirlpool brand is crap”, it takes to long to get service and usually the cost is more than the appliance is worth- and they take it out on him. That is not hard to understand.Bottom line- IF THE SERVICE TECH IS TELLING YOU THE BRAND IS “CRAP” what else do you need to know. FYI- Maytag repairman quoted a new water valve at $70, labor $150 for a total of $230. I paid $600 for the machine- is this a joke? The exact same part was available on Amazon for $43 and was delivered in a day. With the help of a YouTube video I replaced the part in 10mins. On top of the fact that the appliance is crap, it would have taken 3 weeks to get fixed- Maytag is also screwing customers with overpriced parts that shouldn’t have to be replaced in the first place- fair warning, STAY AWAY.

We have a Maytag Neptune washer we purchased new in 2001. The Neptune was useless on My mechanic clothes, but good for delicates and blankets so we have an old style washer to clean my regular clothes. The Neptune was at work on a blanket when we smelled it burning. With it unplugged, I got around to investigating the situation and found the motor control was shorted and burned. I tried calling Maytag. I was asking about an upgraded part or recall. They didnt want to help. The representative was condescending and after I listened to her attitude, she said someone would be in touch. NOTHING. Now I see these suits and I guess I understand. My house could have burned down - they dont care. Maytag is garbage and Im sorry I ever thought otherwise.

I like Maytag but my low water no agitator washer does not do the job as well as it could. Also if a coin gets in the washer it is very hard to get out of the crevasse in the tub area. Most people from time to time have some change ending up in the washer...it should be easier to retrieve.

Replaced my leaking Samsung washer with a Maytag and I really regret the switch. What a piece of garbage. It has been service twice (thankfully within the first warranty year) due to Main control board failure. Seriously, these washers are good for nothing. Also, the Sanitize cycle doesnt do a good job from day one. Save your hard earned money and buy something else.

Actually, I have had my Maytag washer and dryer for 20 years so they are not new but I am thankful for this set because of the workload it does for me. I sometimes wash heavy loads (blankets, bedspreads, small area rugs), and this pair performs superbly. My son wanted to buy me a new set for Christmas last year but I definitely said no. I truly am happy that I bought Maytag and I truly believe that the Maytag repairman is a bit lonely.

My husband and I are retired. In 2006, we purchased a Maytag stove, refrigerator and dishwasher thinking we bought the best. Since purchase, we have had repairs on all 3 appliances costing us over $1000. We are installing our 4th electronic control touchpad replacement today at a cost of $250.00 each. We had a new oven electronic ignitor replaced on the same stove. The compressor on the refrigerator had to be replaced! The drawer mechanism on the dishwasher had to be replaced. We will never recommend or purchase your products ever again!

I have always bought Maytag products, but I will never buy another one again. This washer is the worse. It never has gotten the clothes clean and it is so loud. It has gotten worse. I called someone out to look at it and now am being told that the bearing is going out. We havent had the washer for two years. The cost to repair is going to cost us $574.00. That is crazy. We are going to let it go out and buy another washer, but NOT a Maytag. I will do my research before buying a new washer.

First, the machine is a wrinkle monster no matter what I try. I wash my clothes on delicate cycle to keep the colors longer and so my clothes last longer. This has never been a problem with previous washers. I take them out IMMEDIATELY as soon as the door unlocks and shake them out and hang everything to dry. This worked great previously and I never had to iron anything or put anything in the dryer to get wrinkles out. Now, this washer wrinkles my clothing to an unbelievable extent so that they need to be ironed or a round in the dryer to relax them. This is true on Wrinkle Guard and using the delicate setting, set between medium and none on the spin cycle. Wrinkle Guard? I don’t think so. This thing wrinkles my No Iron shirts so they will have to be ironed or steamed.The washer leaves lint like residue most all of the time on dark clothing from day one. I most recently did a load of black only clothes that I did on delicate, soil level between med to extra heavy, spin speed between med and none, and, because of the dirty clothes issue, I had the extra rinse on. The clothes came out dirtier looking than they went in and looked like I washed them with a box of tissues and too much soap. They looked dirtier than before I washed them and had a whitish and lint like residue on everything. So I ran them through the same cycle/extra rinse again but WITHOUT any soap. Unfortunately I didn’t watch to see how much water the machine sensed that these loads needed and I didn’t see how much water was there - but I did for other loads after - see the next problem below. After the second identical cycle, the clothes had the same residue which I photographed and have enclosed below. (And still a wrinkled mess.)We have found that the water sensor can’t sense the proper water level needed and is likely not functional. Sometimes it seems like it might almost be be appropriate and sometimes not at all. Specifically, after I ran the black load through, I decided to try a small red load before my usual large blue load just to see how much water there was. Same settings as above, 6 small items that barely covered the bottom of the drum and the washer sensed a medium load. Certainly by volume of clothing this was not a medium sized load and if it goes by weight, it was the smallest load possible! Medium water level… These clothes seemed to agitate ok because they were completely submerged in water and came out clean. Then I did the much larger blue load that filled the drummer then halfway. This had so many more items than the red load and weighed way more. I tried the same settings as above and this time the machine sensed a SMALL load and the water level was barely halfway up the clothes, if even that much. So half of the clothes were out of the water and we watched and witnessed that the clothes did not agitate properly. This load came out like the black load so I ran the whole cycle again including the double rinse. This time, the same load was sensed to be a MEDIUM load although NOTHING changed except that the clothes were damp and lower in the tub as they were compressed from having gone through the entire wash cycle. They came out mostly clean, after the second wash, again, likely because this time they were almost covered by the water (2/3rds or so) and could move around a little better but still not great agitation.There almost never seems to be quite enough water so that the clothes are not able to move by the agitator and sometimes we watch and can see that the clothes above the waters never get pulled into the water. I understand that this machine may not completely cover the clothes but this seems way short on water and the fact that things usually come out dirty means something is wrong. There is often so little water that the agitator can’t possibly work the clothes into the water. So, next I ran an Oxi cycle and witnessed that about half of the items were not in any water and were only wet because of the filling cycle not because they were moved around by the agitator. How can the oxi do its job if the clothes aren’t in the solution of at least wet from the solution which I didn’t see as likely as the clothes didn’t seem to move through much if at all?Along with the same water sensing problem, why on earth isn’t there a manual water adjustment? If the water sensor doesn’t work, the other option is only the high fill setting. After finding my clothes still dirty when we first got it, I tried the high fill setting to see if this would help but the clothes still came out with that residue. This was the very first few loads I ran and was assuming it was just user error so I studied the manual and tried everything as recommended. Since reading that residue can result from too much water, I use the recommended sensing feature now. So, we can either have too much water or barely any at all…

Im really happy with my range. The only drawback is that the upper oven/broiler is a little on the small side. The five burners on top are convenient for when I am cooking a large family meal on weekends and holidays.

I am 65 years old and for all of my life there has always been a Maytag washer and Dryer in our home. My great grandmother and great grandfather had a gasoline powered Maytag. My maternal grandmother had wringer-Maytag and my parents have always purchased Maytags. When I was on my own I purchased Maytags. In November of 2012 I purchased a Maytag Bravos XL washer and dryer. I had no reservations because it was Maytag. In October of this year (2017), the washer starting roaring and I had purchased an extended warranty. I called a reported this. A local appliance repair provider was sent out after I called the 800 number on the warranty agreement. I waited several days and finally called the repair provider and was told the parts needed were backordered. Time rocked on several weeks with no communication until I began calling both repair provider and warranty company. Still no washer repair. Ultimately, the resolution was not to repair or replace the washer, but to refund the purchase price and sales tax. The Home Depot salesman that sold us the washer and dryer, as well as the extended warranty coverage assured us that should either the washer or dryer fail it would be repaired or replaced, neither occurred. This left me without a washer for more than a month. Then finally I called the warranty company used by Home Depot and I was told a refund check would be sent for the washer, along with laundry reimbursement check. My difficulty with this is even though I got my money back on the washer and some of my expense on having the laundry and dry cleaning done elsewhere, it does address the issue. Simply, I see the Maytag commercials all the time and they are simply noise on TV now. I am still wondering how this could happen to a washing machine that had less than two and half years of use, never abused, cared for could fail in five years. I was used to having Maytags last decades with little or no repairs. Given the fact this machine was top of the line and well taken care of, I so very disappointed and not buy another Maytag of any kind again. By the way, I have a home in the country with a 27 year Maytag washer and 20 year old Maytag dryer that come from my home in town that Bravos XL dryer replaced. My research during all of this has led me to conclude this is not an isolated incident, but far larger problem with these washing machines. Why has there not been a recall on these inherently defective washers been issued. Where is the justice in this, even though the refund and small laundry reimbursement has been received it does not make any happier. I have lost my confidence in Maytag and I thought that could not happen with Maytag.

Maytag 2000 series front load washer - f you are looking for a front load washer DO NOT buy a Maytag! I purchased a new front load washer dryer set late 2013 and have regretted to washer ever since. Continual electrical problems, door gasket needed replaced almost immediately AND the worst part is that it has ruined over $1000 worth of clothing due to it trapping cloth between the drum and door and wearing holes in them. No matter how I load the clothes or sort them it continues. I have contacted Maytag and was told I have no recourse as the warranty is over. I was very disappointed because I have had Maytag products in the past and had no problems. Please, think twice before buying this washer! It will cost much more than just the ticket price!!!

I purchased a Maytag Bravo washer 2 years ago and it is the worst washer I have ever used. My clothes are never clean. It is always out of balance and is so slow and takes forever to do a load of laundry. It has started stopping on spin and have to unplug it to get it started back then it sounds like a jet coming in for a landing and has to restart the spin about 3 or 4 times before it ever finishes. I have had the repairman to look at it and says there is not anything wrong with it, but something has to be wrong for it to stop on spin and have to unplug it for 5 mins. in order for it to reset itself and start again.

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

I had a tub failure on my washer Whirlpool Duet, which I bought brand new and it lasted 12 years with no problems. The dryer is still in use at my sons house. However, this failure lead me on a search for a set to replace the duet. I did some research and found the Maytag 6.2 Cu. Ft top loader and huge Dryer to match. The set was not cheap and it did have high marks for a great washer. So, I bought them both and had them delivered on 12/30/16. I have read all the owners manual and watched YouTube videos to see how to use this machine with all its pretty lights and sounds. I will concede that the machines look great, very impressive in my laundry room. I would bet it would even be a plus when I go to sell the house.THAT is all the nice stuff I can say. The machine does not clean clothes and I have done all the settings. I have changed laundry detergents, and even tried to add a little more water with a bucket at the start of the wash. (Saw that one on YouTube.) REALLY. That did not work, nor should I have to do that to get it to clean well. The answer seems to be, set the machine on FULL tub of water. So, I tried that for a couple of times and found that the clothes just float around and since they do not touch the Wear Plate they dont get clean. My wife (yes, I am a man that does most of the laundry) said she hates the washer and I was an idiot for buying this expensive piece of metal that does nothing but take up space and leaves spots on your clothes. Have you heard the term Happy Wife-Happy Life. Well not so much for me now.Spending money even $2,500.00 on a washer and dryer seems a little crazy. But I had the extra money and I have always wanted a MAYTAG. These guys know how to make a washer. Boy was I wrong, this machine must be an embarrassment to Maytag. I know I am really shocked that you would sell this machine as top of the line. I am not sure what Maytag will do, but I thought I would give you a chance to make this right. I have attached pictures of the machines installed and pictures of the model number plates. I have faith that Maytag will step up. My wife said this was a waste of time. The ball is in your court Maytag. (Come on Maytag let me win this one.) - Just a man and his dirty clothes.

We inherited this Maytag (Model MGR7662WW) when we bought our house this year. I love this unit. It cooks accurately, its easy to clean and its just rock solid in its performance. I never worry that the cook times are going to be off either. The oven racks are solid and the overall look is nice. Our friends and family love the center grill as much as we do. If I need to pull something off the burner I dont worry that Ill scratch the stove top with this feature. The oven heat is also pretty contained. Our old oven radiated lots of heat through the top. This one doesnt and thats a huge plus. The only reason Im not giving it 5 stars is that the grills are cracking (not the center one). However, I have no way of knowing if the original buyer damaged them or if its a defect in materials. They still work fine but I will need to replace them at some point. Given the cost of replacing them Ill wait as long as I can.

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

Do not buy one. Maytag is unresponsive to repairs or parts that are needed. They are not even manufacturing the part that breaks. If you are lucky, you will find out there is someone who will fix the defective computer board... But Maytag will not tell you. We were without fridge for 4 months... They did not care.

I love my Maytag washing machine. It have different settings for the wash, also a size load for your washing, and I love the rain cycle. You could do single runs with Downy or extra runs which is great. Especially great if you’re doing blankets and towels you need that extra rains. Great reliable machine. Highly recommended.

I spent over $600 dollars on a Maytag Bravo 300 series. The washer has cost me over $300 to fix the latch and 2 months later, it will not spin. I would recommend to anyone not to buy a Maytag product! Garbage! I had a standard Kenmore washer that lasted over 10 years without a problem, paid $300 and still sold it for $100. The funny part is that I sold it to my brother who still uses it regularly and has not had any problems. So what is money worth? Your call.

This washer is no better than a glorified garbage can. Maytag AKA Whirlpool should be ashamed to put their name on this product. Like others before me on this website my washing machine sounds like a jet is taking off in my basement. When I contacted a serviceman, he told me the drum seal is broken and the bearings are shot. I have the machine since April 11, 2011. Not even three years to date! I do not have an extended warranty so shame on me to believe that a 900.00 machine should last well beyond 3 years. Unfortunately, I am getting the run around from Whirlpool as all of you have experienced. This is criminal. Not only are we as consumers being defrauded by irresponsible manufacturing but these huge hunks of metal and plastic are polluting our environment. Our parents had washing machines and dryers for as long as 20 to 25 years and they actually cleaned clothes. We now have high efficiency machines that destroy our clothing and leave them dirty and wrinkled. They are now made to break in 5 years and from what I see on this website the average for breakdown is becoming 3 years. Do you think that this is not by design? The service call turns out to be more than the value of the machine, so the repairman doesnt even profit as consumers refrain from costly repair and repurchase. The only profitability is gained by the manufacturers that keep pushing out junk to the consumer. These manufacturers should be accountable like the American auto-manufacturers became accountable for the junk they manufactured at the expense of a whole city, Detroit.

I bought this MMV4205BAB microwave thinking Maytag was a good brand and I wanted an over the range type. Problems began when it would stop in the middle of a cooking cycle. I called the repairman as it was under warranty. It was decided by the repairman that the weight of thing was too great for its thin frame, not letting the door close correctly. I got a new one and it, from day one, would make a shorting sound every time anything was cooked, on the stove top, under it, while it was on. It finally just shorted out. I have a Maytag washer and dryer that are also junk. So, needless to say, Maytag, 3 strikes and youre out. I will never have another Maytag product and I let others know what a great product it is.

Failure to drain after 3 years. Was disappointing so repairman fixed problem, a fuse, in 3 minutes but charged $300! Since then I make my own repairs and have had no problems that I can complain about. Both Maytag Neptune drier and washer have worked well. Buzzer just failed.

I purchased my Maytag Bravos Washer/Dryer several years ago, and I have hated them ever since. The clothes smell and are wrinkled. The dryer never gets the clothes dry. It will run and run and run, and the clothes will still be wet. I previously owned a Maytag Washer/Dryer for nearly 20 years and never had a problem. This set is a piece of junk. When I go to Lowes or any store for that matter and see someone considering this product, I warn them as quickly as possible to stay away from this product. I will continue to do so. Shame on you, Maytag, for making such a horrible product and for being too weak to stand behind your product. I will never buy Maytag again and will do my best to make sure none else does either.

Maytag Bravos XL - I am having the same problem as everyone else with this washer. My clothes do not get clean and they smell. Maytag advertises tumbling, rubbing action to get clothes clean but my washer does neither. The clothes lay in the bottom of the tub and never move except when in the spin cycle. I am going to file a complaint with Maytag and if they do not refund my money am going to file a DTPA claim against them for false, misleading and deceptive advertisement. They will have to pay up to three (3) times the purchase price of the washer. Maybe everyone else should consider the same.

I bought it from a local dealer so that I could get it serviced locally. I bought it in 2012 and paid $750 for it. I hate just about everything about this (and all modern) washing machines. The deal breaker is all these safety features that are really inconvenient and pointless. If I could have found a good used washing machine at least 10 years old, I would have bought it. This is a Maytag Centennial. I dont like the automatically locking door, the inability to choose the water level myself, and the requirement to use a particular kind of soap. Also, I hate the idea that I have to clean the washing machine from time to time. Whoever heard of that? But you have to do it otherwise your clothes will have a sour smell. These new washing machines are not an advance in technology. I may have to go back to using a wringer machine.

Maytag Smoothtop Double Oven - Bought this stove 2 and 1/2 months ago and already buttons arent working. Very disappointed, not getting a Maytag again.

Brand New 2017 Maytag Dishwasher MOB8959SFZ4 - The first time we used it it leaked from the door. I called the plumber back to make sure it was level and lined up properly and it was. Called the dealer, they sent a technician who sent away for a new latching mechanism. 3 weeks later the parts showed up. Technician installed them ran it through empty and no leaks problem solved? Nope. So I loaded it up and ran it again and it leaked. Called the dealer back but the technician is away on vacation.They suggested that the top rack might be pushing against the door for some reason when it is loaded so I removed everything from the dishwasher and ran it through again but it leaked again.Its something to do with the door not latching properly and it doesnt have a lever that locks like the old ones did. Its such a flimsy product. It baffles me that importers are getting away with bringing this crap into the country. Im now in week 5 with a brand new dishwasher that doesnt work. Maybe thats why its known for being one of the quietest dishwashers on the market.

I bought the Maytag Bravos because I was told it was top of the line and expected that Maytags reputation for quality would provide me with many years of dependable service without problem. Boy, was I taken for a ride! Unless you have a lot of money to spend, DO NOT buy a Maytag Bravos washing machine. After only 3.5 years of normal use (3-4 standard loads per week) and doing everything as suggested by the owners manual, my machine has developed a bad drum bearing. The cost to repair this bearing is $400 for parts and $200 for labor. In other words, I am forced to buy a new machine after ONLY 3.5 years of use. When I called Maytag customer service department to question them about my problem, their response was there are no recalls on your machine, so we cannot do anything for you. When I further questioned them about the lack of quality/dependability my machine provided, they again said, Sorry, the machine is out of the warranty period. Thank you for buying Maytag. If you buy one of these washing machines, you better have the extra money to buy an extended warranty.

This is the worse designed product. The gaskets on the door keep making mold. The end caps that hold the pantry lid keeps snapping off, had to replace them twice. It is a very elaborate and complicated installation which of course they will not cover. The water dispenser is inside the left side of the fridge and the water runs so slow, that you lose a lot of the refrigeration by the time you fill a glass.This appliance is very noisy. The customer service is sometimes nonexistent. I called on 9-16, I waited 24 min on the line and decided to hang up. The next day I tried again after 15 min they hang up on me. I tried again later got Customer service, but no they could not help me with installation of a replacement for a warrantied part that snapped off for no reason at all. I have complained while this appliance was under warranty, and after. They do not care. My advice is stay clear of Maytag refrigerator, I CERTAINLY WILL.

3 year old Maytag Washer model MVWX600XW broke. Paid $345.55 for extended warranty. I had to wait 10 days for Appliances Unlimited to fix the washer in Sept. then the washer broke again in November needing 3 more parts including a motor. It took almost 2 weeks for Appliances Unlimited to come to the house, then I have to wait 5 weeks for a new motor to be in stock.

I purchased a Maytag dishwasher May 2019 Model# MDB4949SDE3 Serial# F80446835. It has to be one of the worst purchases I have made in a long time. In fact, I wish I could return it and start over with another brand. My glasses come out of the cycle with film and silverware is spotted. I have tried everything from scrubbing and rinsing before I put into the dishwasher, every product on the market, making sure my hot water heater is on high to settings for the longest most powerful cycle and it still continues to disappoint. My warning is DO NOT buy this dishwasher.

The best we can tell, we got our Maytag in 1991. This was because the repairman told us that was the last year they made parts for it. It ran wonderfully until 2018. The water valve broke, but a repairman easily fixed it. In 2019, it stopped running. The repairman fixed it, temporarily, he said. He refused to charge us for his work because he said we might get a few more loads done before it completely pooped out. Were still using it. I love this machine. It has gone WAY past the expected life span of a washing machine. Weve had it for 29 years!

I have a Maytag microwave and stove in my condo kitchen. Both are about 4 years old. Ill never buy another Maytag appliance again. This stove had problems from day 1 and the support was dismal. I had [bought] an extended warranty, which covered nothing (I let it expire and didnt renew). The microwave handle came off in my hand a few months ago. I stuck it back on with gorilla glue. Now it is starting to shut itself off, as if it lost power then mysteriously turn itself back on. Im sure there will be a new microwave in my future and it wont be a Maytag.

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

I bought this washer from Home Depot and was told I could load large comforters and even sleeping bags in it because there was no center agitator. There NEVER seems to be enough water to wash and rinse clothes completely. The water saver feature cannot be used as I have to use extra rinse cycle EVERY load to rinse soap out of clothes or I get white residue spots. I have MANY MANY shirts that have small tears in them I believe caused by this washer. I have monitored shirts I put in the washer and again today lost another high quality fabric T shirt. I have saved all of the shirts in hopes that one day there will be a definitive report that this washer design stresses clothes and damages them. I am going to purchase a new washer and it will not be a model like this.

This oven isnt even worth talking about. Just dont buy it. I used to bake a lot, but my recipes dont turn out anymore. My old oven was much easier. I dont know what the problem is, but I suspect it is oven temperature. The door also sticks. I have only had this a year and am ready to junk it.

I purchased my 10kg commercial Maytag dryer in March 2015 and started using it in May 2015. Within two months the heater had broken. I contacted the people I bought it off and it turned out I had to contact Whirlpool. It took them 8 weeks to get my dryer going again. The dryer broke down again in November. This time it was a sensor. Again I had to contact Whirlpool, it took them three weeks to get it going again. Being a care home the dryer is essential to our business. We were led to believe when we took out the extended warranty that the dryer would be fixed within a week. I will never purchase a Maytag again or anything to do with Whirlpool.

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

I bought a Maytag washer in Sept. 2018 because the company had a reputation of making quality products that did not need repairs. I was wrong. Because I live alone so at most I washed two loads a week, so the company cannot say it had been overused. After a little more than a year I notice at times the wash cycle took too long. One time I tried the 2 rinse cycle and it would not quit washing. A repairman reset the computer to factory settings (he was at the house repairing a refrigerator) and it worked for a few months trouble free before dying. I will not purchase another Whirlpool product since the company did not stand by its product.

Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for 2.5 years. The unit started beeping at random times for about a week - then went dead! Sounds like other reported failures and it is unlikely repairs will be permanent! Never again Maytag.

I purchased my Maytag and Im not happy. There is agitator in center and it seems to always tangle up my clothes and has torn several garments. And there is no fabric softener compartment but there is the one for bleach. If I had to do over again I would have several compartments for bleach and softener, and no agitator in center. But I made the purchase and it does clean the clothes but they usually in a ball when and tangled when complete.

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

On 12/09/12, I purchased a Maytag washer, model mvwc200xw, from our local Menards store. About 6 months ago, the washer started making a slight banging noise, and would occasionally move in the spin cycle. Now, when washing a small to medium size load, the banging noise is very loud and does a lot of moving. I found nothing in the troubleshooting guide to help me on this, so I looked on-line and found several websites discussing this same problem. They stated that the problem was a snubber assembly and the replacement part would cost $4.55. They also said the washer would have to be taken apart to change out this $4.55 part.I watched a you-tube video of someone changing this part and quickly came to the conclusion that I would need help in doing this. A comment was left in the video from a Maytag repairman saying that the person changing this part was not doing it in a safe manner. The repairman stated that changing it in the way this person described in the video was DANGEROUS! I wrote an email to Maytag customer service explaining the problem and asked if there was anything they could do to help me on this 1 1/2 year old washer. I received an immediate email stating they would get back to me in 3 days. Ten days later, I finally received a reply. I was told there was nothing they could or would do even though I was a valued customer and that they understand and appreciate my feelings of disappointment.I worked for a large department store from 1970 to 1990 and sold appliances, one of them being the Maytag brand. At that time, they were considered to be a top of the line brand. This was why I purchased Maytag appliances for over 40 years. I am surprised and saddened to see a lot of on-line complaints against Maytag appliances and also that this 1 1/2 year washer needs to be repaired so soon. Obviously, times have changed. I figured it would cost me at least $100.00 to have this washer repaired. Rather than do that, I am going to take this in need of repair to a scrape recycling center and then go out and buy a new washer, but it will not be Maytag! Maytag will never disappoint me again!

I bought a new smart washer and dryer from Maytag in mid-2019. Beginning in the first few weeks the machine did not perform as expected--cut off in middle of cycle, door failed to unlock at end of a cycle, constant error messages that made no sense (power failure when power didnt fail, codes that arent defined in the owners manual). To make a long story short, the company that does their warranty repair, which has worked on the machine approximately 8 times, tells me there is nothing else they can do, the machine is a lemon. But their customer service department refuses to replace it. They say it must be repaired, yet again. But the parts are out of stock (which should be a pretty good indication that theres a problem with product quality). So I am to wait. How long? They dont know. Call again tomorrow.Do NOT buy a Maytag appliance. Customer service does not stand behind their products and the products are no longer up to the quality I had previously expected from Maytag. Additionally, telephone wait times on the customer experience line can exceed an hour and are customarily over 30 minutes. Never had an experience like this with any other major appliance customer service department.

I purchased the Maytag 6.5 inch electric convection oven about 2 years ago. I wish I hadnt. The oven temp is way off, it cooks unevenly, the back burners hardly work, and the back burners on the stove top barely work, the knobs get stuck constantly, the self cleaning does not work, and the glass part of the door allows dust to get trapped in the glass. The range is $800+ piece of junk, best used at the scrap yard. Today, I turn my oven on, and the element underneath the oven pan caught on fire. Now its broken in half, and needs to be replaced. I look up the QR code, and come to find out the oven is actually a Whirlpool, with Maytag labels on the outside. I would have never purchased this range if I knew it was a Whirlpool. I have always had issues with Whirlpool appliances. This is a fraudulent product, and deceives the customer. Why sell it as a Maytag, when its really a Whirlpool? It should at least state that fact on the description, and salespeople should advise the customer. Now I know why its a piece of junk, because its a WHIRLPOOL!!! I will never buy a Maytag or Whirlpool product ever again. I have always stuck with Maytag appliances. Every appliance in my house is a Maytag, or are they Whirlpool?

Was assured the washer could do comforters, etc. Well, I took a video of the washer doing 5 t-shirt, 1 pair of pants, and 3 pairs of socks on the power wash cycle. Nothing tumbled. All the plate did was swish some water around on the bottom. Clothes werent clean at all. Check my Youtube video, and you can watch the leg of the pair of pants sticking up out of the water and never getting back down in to get wet. Horrible horrible machine. With that said, called the company I bought it from, and they arranged for a front loader since Id only had the machine for a couple hours. Stuck me for a second delivery fee though, which I wasnt happy about. Well see when the new one gets here Tuesday.

Bravos XL top loading washer looks nice and very large, but thats about how deep it goes. It leaves even a small load half-unwashed unless you select deep water wash and even then it FAILS TO USE ENOUGH WATER. I tried to go and fill it up once with tap water and it totally DRAINED THE WATER AND SOAP before it unlocked! It was on Deep water wash and the top of the load was totally dry as I dumped the hot water onto it.It is a bad design and it should have never been sold. I know it has special places designed only for HE detergents but when you try to use a Tide Pod the detergent NEVER FULLY WASHES OUT OF THE CLOTHES.... Too small a load, too big a load, exactly 5 pounds or exactly 10 pounds it really doesnt work very well - AT ALL! I was thinking that I might like to get some SHOS at the low price it is but now I can see why they are definitely not getting back into business.

I absolutely do not like the fact that you can’t choose what size load you have. The washer wants to do it for you but it is not very good at it. You have to fool the washer to get any kind of water level or just use the deep fill every time which is what I do in order to get the clothes clean! This defeats the whole purpose of trying to save water. Also there are too many settings. I mean we’re just washing clothes here not flying a jet. I personally would prefer dials instead of the digital instrument panel. So much easier.

I purchased two Maytag appliances; PC-touch control 500 Electric Smoothtop and a dishwasher. In less than two years, I have spent over $1,000.00 repairing these two appliances. With my stove, I have replaced the PC control board and the oven light kit. Less than a year and a half, I now need to replace the PC control board again. I have been a Maytag customer since 1976. The dishwasher had a recall for the heat element and I replaced the control panel control board and door lock switch and the main control board. I will never buy Maytag again.

Worst Washer ever...hated it from day one of receiving it (but couldnt return because moving into new place, took awhile to get it installed, and by then the 30 day return window had lapsed, so now stuck with this piece of garbage!). Is ALWAYS off balance whenever you wash anything of weight (i.e.: towels, sheets, blankets etc.). It takes me close to 2 hrs to get these items washed because I have to keep starting and stopping it to try to get it to spin dry because it ALWAYS throws the items so is off bal. and wont spin. Then when you hit pause, adj. bal., & start it again, it starts REWASHING the items (instead of continuing on from where you left off), and sometimes when it cant balance in the spinning cycle it just shuts down making you think the full cycle is complete, only to open up the lid to find your clothes all sopping wet. Also, NONE of the cycles will get any of my clothes clean...it just uses so little water your clothes come out feeling grungy and still dirty. I have had to resort to ONLY using the BULKY cycle because it is the ONLY cycle that will use a higher water level (mainly because bulky items like towels will absorb the water so it needs to add more). With this cycle at least my clothes dont FEEL dirty when they are done washing!There is no way of knowing how much time is left on any of the cycles, which is a real problem when you have to start and stop it, because you really have no idea how far back it goes to start itself up all over again. There is just no way to time it, because it keeps messing up where you have to keep stopping/starting it, and then you have no idea of time frame. Never saw a machine built so UNUSER friendly!I will NEVER buy a MAYTAG washer again, and NEVER will I buy a washer unless it HAS the center agitator, and a control for water level. These HE washers are the worst, and unfortunately they are now the only washers being made, but without water, clothes just DO NOT ever get clean anymore no matter which fancy and expensive detergent you use. HE washers are HORRIFIC. I may just buy an old style used washer with the agitator... at least I wont be wasting energy to only wind up with STILL dirty clothes when using HE washers! FINAL NOTE: AVOID Maytag HE Washers at ALL COST! You will be sorry if you decide to purchase one!

Dont buy a washer from Maytag, they put it together wrong and the transmission leaks so it will stop spinning after time and then it fries the motherboard. Too expensive to fix so you have to by a new one.. Their 10 year warranty is a joke and doesnt cover anything hasnt even been 5 years yet. Garbage products.

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

Would need 3rd panel for 8-year dishwasher - Either no lights come on the panel or Load done lights, like now. It has happened so many times over the years from about a year after spending a lot of money on a Quality unit. Many times I was able to operate it after turning the breaker off/on or leaving it to sit for a week or so, multiple times! Also, the rubber on the racks did not do so great - peeled and rusty. I did apply rubber repair multiple times, then got new racks at my expense. Several other brands bought over the years lasted 10+ years with no repairs!