Have had it for 2 years now and its leaked out the bottom since it was 6 mos. old. Now the ice maker has fried a motor and were having to repair it already. Cant believe we spent a small fortune on this fridge and are having constant problems with it.

I purchased a Maytag quiet series dishwasher (Model Number: MDB6759AWW) for $500.00 in May 2009. Three months later, I started experiencing difficulty with the control panel. One light would continue to blink and it would not do anything else. I called to have it repaired but by the time he was to come out, it started working again only to stop working again the next week. On 7 Oct 09, the repairman came out and replaced the panel. Then, about six months later, it stopped working again. I called again but canceled the appointment because it started working again. Then, after having it for one year, it stopped working again and I called only to be told that it was no longer under warranty. Now, we cant get the control panel to do anything. From all the other similar complaints I have read, it seems like there is a defect with the control panel. A dishwasher should last for more than one to two years. This is very frustrating.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

We owned the washer for 2 years and 2 days when we got a code F70. After searching online, I found hundreds, if not thousands, of reviews and self-help forums that show this product is in dire need of a recall. The problem I had is the motor control unit (MCU), which is a $225 to $275 part online. However, Maytag will only replace the board under extended warranty with a refurbished board that they say costs $330, whereas they say the new one is over $600. Why is it that Maytag charges double what everyone else charges? If so many people are having these problems, it is obviously a defect and should not be the consumer’s responsibility. It is obvious that this is too common of a problem.

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

I purchased this refrigerator 1 1/2 yrs. ago. The refrigerator stopped getting cold about 3 months after warranty expired. I called Maytag company and told them how disappointed with their product and also how angry I was after spending $1500 only 18 months ago and now it is useless! They kept asking me if I bought the extended warranty and I said I didnt think I would have to after buying a brand new product. And then it breaks so soon!! And now they want me to spend an additional $359 to get the warranty... what a racket! She told me to look under the fridge for leaks. Sorry I cant, Im disabled. She said too bad and would have service man call me but that would be even more expensive. Woops, disconnected.

My freezer has been leaking from the bottom for a few months and now the icemaker has quit working as well. The refrigerator has been purchased less than two years ago. The warranty is expired. I will not fix this refrigerator, as it is a gigantic piece of junk. However I would like to be compensated by Maytag at least 1/3 of the price so I can have it removed from my house before it creates more damage to my floors and subfloors.

The stove functions are excellent and the temperature of the burners and oven causes the food to cook even. However after about 6 months the heat from the burners causes the coating on the stovetop to burn like its baking and it cant be cleaned. Now the coating around the burners is horrible and burnt.

Both my washer and dryer are Maytag. Dryer element shorted out but was still under warranty so was fixed. Washer is very loud and now makes a rattling sound. Every so often it will hang in the middle of a cycle and the lid wont open until I unplug it.

We are on our 2nd Maytag refrigerator in 6 years and both units have failed. Maytag will not stand behind their product and the service company declined to come out to look at the unit because we were upset and contacting the BBB. So we have spent thousands on 2 refrigerator units that have lasted 2.5 to 3 years a piece. If I could give no stars I would and I would advise to look at other companies and models.

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

Maytag Bravo Washer - I recently purchase a fairly expensive washer built by Maytag. In my opinion it is the worst washing machine I have ever owned. Again in my opinion their advertising about being such a reliable company should be considered false advertising, and near criminal. If you had a lower rating I would use it. Absolutely you should never use the word Bravo in a description of this washer. I will never purchase a Maytag appliance again. Check the internet for reviews before you purchase. I had just came out of surgery and in a wheelchair and trying to move back home and didnt do my homework.

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

Purchased Maytag Model MVWB865GW0 Ser# **, had it ONE year, circuit board and switch have gone bad, will not turn to change the type of wash cycle and the lid will not lock, which makes the washing machine not start to wash. Contacted Maytag to request a service call, per the service team the circuit board will cost $300, plus a switch $75 and Labor $100 plus tax. We will be better off buying a new washing machine! We should not have this high cost within ONE year of purchasing! Will not purchase a Maytag again!

I purchased this dryer in September 2011. By August 2012, one month before the warranty expires, the thermo fuse blew and the dryer would not dry; no heat. I replaced fuse and 30 days later, it blew again. I replaced it again and now, March 2013, 6 months later, the same thing; the thermo fuse blew, no heat. The vent is clean and air flow is very good. Maytag will not admit a problem. This is not an inexpensive dryer; it may be cheap, but not inexpensive. Maytag quality appears to have vanished. I have Maytag throughout the house but will think twice before purchasing Maytag again. Chinese produced parts/products are inferior. Maybe Ill look at Bosch or LG from now on.

Bought this Maytag Bravo washer in 2013 expecting long service life like I had with my previous machine. After 2 years spin cycle noise got progressively worse. Until now it roars loudly and keeps stopping in the spin cycle for rebalancing. Called Maytag. Experience was as described as others have reported with them and their repair service. Absolutely no help unless I spend another $310 for extended warranty to cover the $380 part (tub and bearing - 1 unit - cant get only the bearing). Paid $800 for the washer now more for the repair wanted. $1100-$1200 for a machine that will need repair again in a couple of years? Dont think so. This machine is only good for a boat anchor. Going out today to buy a replacement for $400 and it wont be a Maytag or its affiliates brand. Feel like a class action suit would be good for Maytag to wake up to.

Sheet of ice in floor of freezer. Leaks water from bottom, and now ice crystals in freezer! French door MF12569VEA1.

The Neptune Front Load Washing Machine I purchased in December of 2007 started sounding like a jet taking off, about three months ago. The noise has become unbearable. The repair person said that the whole drum needs to be replaced and it is not worth fixing. Are you kidding me? This was an expensive washing machine and now we have to get a new one? We cannot afford to get a new washing machine. We need an explanation of why this would happen and from the other complaints I have read on the Maytag website, we are not the only ones. This is the second time something has happened to this washer, the first time, it was under warranty (only a few months into the purchase and the pump was bad and was replaced). What is the company doing to help people with this faulty machine?

I purchased a Maytag refrigerator, stove, dishwasher and microwave in 2006. Like another commenter, I also insisted on all Maytag appliances. What a huge disappointment. About four months into owning the microwave, a computer module had to be replaced. The microwave stopped working about six weeks out of warranty. It just stopped working, period. I was told by Maytag that they consider microwave a disposable product and they would not cover the repairs. It was cheaper to buy a new one than repair the old one so I replaced it with another brand. The dishwasher failed after 4.5 years (would not drain) and again it was cheaper to replace it than fix it. The oven range handle broke off (normal use) in August 2011 and that cost me approximately $200 for the part and the service call. The refrigerator has had two service calls for the ice maker to replace the motor. The first was covered by Maytag, the second by me. This occurred when the unit was approximately three years old. In August 2011, I had another $90 repair because the ice maker drain (?) was plugged and had to be cleared fixed. I have never been able to pay what I paid for these appliances. Prior to this, we always purchased a middle-range appliance and we never had problems like this.I will never purchase another Maytag product again. This is so disappointing. I live in MI and I wanted to support a MI business. Unfortunately, I wont be able to help out this particular company any longer. Dont buy Maytag appliances. It is a waste of money.

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

We purchased our Maytag Bravos washer and dryer in 2008. Within a year, the hinges that held the door open on the top load washer broke. In year 2, the area around the fabric softener dispenser rusted so badly that it almost completely ate the porcelain enamel away. In year 4, it started making a noise that I will compare to a jet on takeoff during the rinse cycles. It continued to work but got louder and louder. We looked into the cost of the repair, which was going to be $350 parts + labor. If it had been a good machine, we might have considered fixing it but it wasnt. Even a set of sheets could put it off balance, which stopped the machine with the wash cycle incomplete. It also set its own water level based on the weight of the clothes and many times the top items came out with dry spots that hadnt even been submerged throughout the whole cycle. Consequently, the clothes were never very clean and I would have to rewash many loads. This machine was not cheap - around $1,000. I was so frustrated and felt completely taken by the Whirlpool company again. We have had many unhappy situations with their products over the years - Kitchenaid, Jenn-Air and Maytag. We finally learned our lesson and researched washers online. The best rated that we could find was Speed Queen. We couldnt find it in Canada, so my husband drove 5 hours round trip to the US and bought one. We have had it 4 months now and the difference is unbelievable. Our clothes are clean again. I can set my own water level and the hot cycle actually gives you hot water. It never goes off balance no matter how many or few clothes it has. If I see that I need more water part way through a cycle, it has a button that lets you add some part way through. It doesnt have a lot of bells and whistles. Its a basic but excellent machine that is a pleasure to use. I would recommend it highly. I realize it has only been a short time, but my Maytag never performed like this machine even from day one. It reminds me of my very first washing machine many years ago, an Inglis, which never had a repair in 15 years of use. If our dryer goes, we will definitely buy Speed Queen. The trip is well worth it.

This is a continuing aggravation! On July 27, I discovered the dishwasher (MDB7600AWW) tub had developed a crack in the bottom right rear and had warped my countertop and the floor under it was full of water! I called the appliance store where it was purchased and was told to call Maytag. I have a 20-year warranty on the tub with free replacement of the unit if it fails. I called Maytag and was told we needed a service call to verify. I scheduled it for July 30, and 3 minutes and $75 later, yup, tub is cracked. Its a known problem, and the dealer has already replaced some for customers. I called Maytag to get the ball rolling for replacement. I spoke with Jennifer and was told shed get back to me.Meanwhile, we went to several stores, checking out other Maytag models. So, Id have some idea of what was available as a replacement. I called Jennifer on July 31 with a suggested model Id find as a suitable replacement. She said shed check and get back to me. On August 13, I called Jennifer for some answers, got the voicemail, and left a message. On August 14, I went online to chat. Finally, I was told Id have a replacement in 10-12 days. Id be contacted to schedule installation. On August 16, I called a local dealer again. He cant understand the problem. Hed replaced two others in a few days. He made some calls for us and gave us the name and phone for the company replacing the dishwasher as well as the work order. Installation was tentative for August 23. (Hed been cut out completely!)I called Optimus Solutions, and theyre awaiting shipment. Tentative installation was on August 23. On August 22, theres still no word. I called Maytag customer service. Sorry, it was shipped to the wrong address, so it was shipped back! Its now in transit and supposed to be delivered to Optimus Solutions today but not being scheduled for installation until August 31!This has become one nightmare after another with everyone pointing the finger at the next guy. Phone calls get only the same runaround. No, speaking to a supervisor wont help - theyll tell me the same thing. Isnt that convenient! Meanwhile, Im still washing dishes by hand and having psoriasis on my hands, which are like two pieces of raw meat right now. It is beyond aggravation; its bordering on torture! (No, I cant wear gloves. They make my hands sweat and even more sore!) Besides, I shouldnt be washing dishes by hand. I paid for a dishwasher that failed through no fault of my own, and now, Im being punished for purchasing it. I can guarantee that if I had no warranty and had to replace this dishwasher, it would have been replaced immediately!Never again. I purchased all Maytag products for my new home. As they fail, I can guarantee I will not be replacing them with Maytag or Whirlpool, which now owns Maytag. I will be telling everyone who will listen to stay away from Whirlpool and Maytag, because their customer service sucks big time.

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.

We bought a Maytag refrigerator less than two years ago because... its Maytag. Less than a year later we had five service calls. The refrigerator wasnt cold, the freezer was the temperature of the refrigerator and it took two months and two different repair companies to fix it. And now... yes, the same problem seems to be occurring. It was a leak that was supposed fix. Cant bear the idea of going through this all over again. NEVER again Maytag!!!

We purchased this Maytag about ten years ago. We had an old brown one that had to be 25 yrs old and still going. This piece of junk has had two compressors; the ice machine hasnt worked in a year, and now it just went out again (third time weve lost hundreds in food)!!!! About the same time we bought a Woods freezer on the cheap, this freezer sits in the laundry room crap piled on it and around it and never have had a problem. Maytag = $2500.00 boat anchor.

Went from an old simple Maytag to newer model, but still somewhat basic compared to others. However still getting used to the water saver feature in that getting in the right amount of detergent as not to have it set on my clothes and having to put through another rinse cycle and a more slimmer agitator. But do like the Maytag brand.

I received my Maytag dishwasher in November of 2013 from Home Depot (It was a month overdue the expected delivery date). It was installed by a certified electrician/contractor. By February of 2014, the control panel had to have its first replacement. It is now July 2014 and we are having the repairman come out to replace the third control panel this Monday. Supposedly there was a recall on the control panel and the one replaced less than a month ago was the improved/repaired one. We are beyond frustrated. I too sought Home Depot for help after the first repairman they suggested charged us almost half the cost of the dishwasher for his repair. I have already sunk over the price of the product into repairs. My Maytag dryer broke last week as well. Someone needs to get involved with this situation, perhaps a contact to the media? I think we are all being scammed and deserve refunds by Maytag for the dishwashers and our repair costs.

My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

I purchased this washing machine from Home Depot in 2012. I am amazed that it lasted this long after reading the reviews on here. It will not drain water, it will not spin. I see many customers bought the same washer and are having multiple issues. When will Maytag recall these machines? Overpriced and unfair to consumers to sell something that is broken or not reliable.

We purchased a Model MDB8949SAWO Maytag dishwasher in September 2012. The control panel failed in November 2015. We wrote a letter to Maytag (Whirlpool) expressing our disappointment and received a call from Maytag customer service. The Customer Service representative informed us because we contacted our local repair facility directly, no reimbursements would be provided. During a subsequent follow-up call, I was informed by the Customer Service representative that Maytag manufactures quality products and that no premature failures were occurring with Maytag dishwashers. The Customer Service Representative stated that we should have purchased an extended warranty which lends some support to the fact that Maytag dishwashers are essentially junk. Never again will we purchase any Whirlpool products.

Purchased a Maytag fridge in August of 2010. Had issues January 2014 - needed a new circuit board. At the happy cost $230.00. Well it is now May 2014 and had to have the repair man here again for another circuit board $258.64. Maytag will not stand behind their product or parts they use in their products. They flat out told us that we shouldnt have to replace the circuit board that often and then said they wont stand behind it. So buyer beware. DO NOT BUY ANYTHING MAYTAG!!!!!

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012. It has leaked repeatedly onto my wood floor. The water also collects and freezes on the floor of the freezer. I already have warped floor boards as a result. I just got it fixed. The repair person said he has done over 200 of these repairs in the last year. He also said Maytag knows its a defect and has supplied them with replacement parts. The company apparently tells its repair companies not to discuss this with their customers. I have yet to contact Maytag, although apparently from others experiences that will be futile. Im willing to join others in pursuing this. I had a 40 year old Kelvinator which was still working well which I replaced with this refrigerator when I redid my kitchen.

We bought a Maytag refrigerator two years ago with the front french doors and bottom pull out drawer. We chose Maytag because we thought it was a name we could trust, a good quality merchandise. However, in the last two months, we started having problems when the fridge wouldnt stay cold, the freezer worked fine. We removed everything from the freezer and my husband found the freezer needed defrosting as the back of the unit was a solid sheet of ice. It took hours to defrost and we thought that we had the problem taken care of.. and that we wouldnt have to worry about this happening again. However, we have now had to do this three times in the last two months!! I love the style of this fridge..but am getting SO ANNOYED with having to rip everything out of the freezer and spending HOURS to defrost it! I have NEVER had this problem with any other fridge!! Im ready to replace it, but weve only had it for two years, and I shouldnt have to be spending a fortune on ANOTHER fridge after TWO years!!

They are coming for the 7th time to fix the ice maker. Three full replacements. The bottom of the freezer had a buildup of ice, another call to repair. I know where the Maytag repairman is, hes at my house.

Purchased refrigerator model # MFT2976AEMOO September 2013. First repair was 1 month after purchase. From compressor to moisture build up inside fridge. 7 repairs in the first year. Customer service disgusting. They simply dont care, and do not back their products. Work time lost waiting at home for repairs. Service men come and always have to order parts, which means 2 service calls for each problem. Our service man broke one of the drawers when removing it to do a repair which meant another visit for that replacement part. Continued to have more problems when warranty was done. Just replaced my 3 year old fridge. Could not afford to keep it any longer. Have never been more disappointed with any appliance that I have bought. Will never buy MAYTAG again. Product is inferior.

I bought a refrig from Home Depot on 10-16-2012 two years ago and it doesnt work, but they only put one year warranty on. So had to go out and buy another. My complaint a refrig should last more than two years but they were going to send repairman out on my expense and more than likely would of cost me the price of a new one.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

Got the dryer free when we moved into our townhouse. We had been doing 2-3 loads a day for almost 8 years. The dryer was old when we got it. No complaints. Just wish there was some way to fix it. But mechanic said, No way. Almost a valued member of the family. Say 2 loads a day, 7 days a week, 52 days a year. This is a lot of loads. Remarkable. New machines cant do that today says our mechanic, they are not built to be fixed. Now, when broke, replace, don t fix.

I bought a brand new refrigerator and about four months into using it, the freezer door began to become loose and opened by itself automatically. It also started to leak so I called the company continuously looking for a solution. However, they never resolved my problem. The company sent a technician. However he was unable to fix the problem. The technician said it was fine and did absolutely nothing. And now I am still waiting, but now your company says my warranty is up EVEN THOUGH I called much earlier and your company did NOTHING to help me. I need someone who can handle my problem. Ive been using your products for many years, and have always been satisfied by it. But this refrigerator has changed my perspective. I hope you give this a peace of mind and treat your other customers better.

I can’t seem to get any help with my dryer. I have replaced the drum 2 times and thermostat 3 times. Model number is mde9700ayw. Serial number is 13229569gp. I simply want a new dryer that works.

What junk. Bought this gx2shbxvy05 french door fridge. In less than 16 months the freezer is fine the fridge section gets up to 80f. Throw all the food away. Found the freezer coil covered in ice. Took the back panel off and noticed ice around the copper tubes by the compressor going up into the body. Not good. Put a small brick heater in and slowly melted the ice into the drip tray. Warning, it filled up 4 cups of water and of course spilled and killed the wood floor. After the clean up. Plugged the unit in and it seemed to work for about 3 months. Now its dead again. Looked into parts around 300 to 400 bucks plus labor to replace the system needed parts. P.S. the fridge, this junk replaced is downstairs working after 25 years not one issue other than the color. NEVER BUY A MAYTAG product please. TRAIL APPLIANCE should never have sold this product and should have stepped up to help out. Wont buy from them again.

Does not rinse clothes or dispense adequate water. This is the worst washing machine I have ever owned. Dark clothes come out of washer with white dust/soap residue on them. Clothes often come out of washer dry - never touched by water in the wash cycle. The spin cycle knots the clothes into a heap. As for the dryer, pulling out the lint filter leaves lint particles all over the top of the dryer. Poor design.

My dishwasher is less than 2 years old - has only been used a total of less than 12 months as I am seasonal in Florida. The control panel has failed. It will cost $275 parts and labor to fix.

Pretty much the same complaint as Ive read about the Maytag dishwasher control panel issue. I purchased ours in Nov. 2009, issues began in April 2011, and service call for $129 where the technician said it needs a replacement control panel. I spent another $130 for the part and warranty on this specific part. In December 2011, issues occurred again. I ordered a new control panel in January and was told 3-5 days, called after 10 days and was told it was on backorder and should be shipped sometime in March. Youd think the Maytag President would be embarrassed for producing a product like this that in my eyes has tarnished what was a reputable household brand. Not that it will do any good but I will mail a letter to the President. One positive, our kids are learning to wash dishes the way I did as a kid, by hand. I sure hope the new control panel we hope arrives in March fixes this problem for good.

We purchased a Maytag dishwasher in July 2013. In October 2014 it stopped working. None of the buttons on the control panel would light up. The service technician diagnosis was that it needs a new control panel at a cost of about $200.00. We chose not to do the repair since the technician recommended against it.

I purchased my Maytag 4 door refrigerator with the freezer at the bottom (model #MFX2570AEM) in December of 2012. A couple months ago it started leaking small amounts of water. I now notice that there is such a build-up of ice under the freezer drawer that it wont even close properly. I, like all the other consumers that have complained am fuming mad. I purchased the Maytag brand because of its great reputation for quality products. However, this is totally unacceptable that I should be having issues with this refrigerator less than 3 years later. Shame on you, Maytag!!!

I bought a Maytag Bravo washer and dryer 18 months ago. While taking clothes out of my washer, I noticed that the plastic collar above the washtub was shredding around the edges. I called the manufacturer about it. Because it was more than 12 months old, they refused to do anything about it. I feel that shouldnt happen so soon after purchase. Im a single person and dont do that much laundry. The piece should be made of something more durable. I will never buy another Maytag product. Is there anything further I can do to pursue this?

Washer would stop right after it started. I googled the problem and found out it was a bad lock. These Bravo XL units were purchased in 2015. Called an appliance repair and they charged me $250 to replace the lock (service call was $98.00 and labor was $90). The repairman left and I started the washer. There was a loud sound coming from it. I called the repairman back and he said it was the gear case and basket. He said the basket was covered under the warranty but the gear case wasnt. Would be about $750 to fix....no way was I paying the cost of a new washer to fix this less than 4 yr old one. I called Maytag. They couldnt help me. I should have purchased an extended warranty they said. The cost to purchase the extended warranty is now $394.00 per year....please do not purchase a Maytag/Whirlpool appliance unless you like buying extended warranties.

Last week I noticed that my freezer motor had a build up of frost. I melted it with a hair dryer. 2 days later there was a layer of frozen water on the bottom of my freezer as well as a layer of water on the first shelf in the fridge area. There is no way to access the drainage tube. I thought that the coils needed to be cleaned. That was not successful either since the coils run horizontal and only the front section can be vacuumed. Today, again the freezer motor area is frosted and layer of ice on bottom and the motor is making a terrible noise. How disappointing for a less than 2 year old fridge.

Maytag Bravos Series 300 - I bought this machine less than a year ago. There is an awful smell coming from the machine that I never smelled from any other washer I have owned. The clothes do not look, feel or smell clean, and my towels are ripped. It is an extra large washer, yet when blankets are put in the machine bounces and shifts. After reading all the reviews, it seems I am not alone in my concern with a machine that was not only expensive, but was told it is a great product. Maytag needs to do the right thing and recall this machine.

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

Love, love this washer. Does an amazing job cleaning colors, whites, and bulky bedding. If you like Tide Pods or other liquid pacs, this might not be the washer for you as they tend to end up inside the gasket. Powder-filled pacs are no problem however.

I have a 6-month-old top load Bravo Washer. It has destroyed two bottom fitted king size sheets and 2 shirts that now have holes. It apparently slices the sheets during agitation. I have a service policy and called the service agency. The technician said there was nothing wrong with the machine, yet it literally ate 2 more items. Help! I need a solution to this problem.

We purchased our Maytag dryer at Home Depot a couple of months ago. We just called Home Depot for the second time because the dryer handle broke off while opening the front load door. We called Maytag and they tell us to call Home Depot and the only thing they are willing to do again is fix the door handle which will probably break off again while Im in the middle of laundry and cant retrieve clothes from the dryer because there isnt a handle to open it.Im convinced the dryer has a defective handle, and the dryer should be replaced considering what we paid for it. But Maytag or Home Depot doesnt want to do that. I will never buy Maytag products again and thinking of buying products at small appliance stores who stand behind their products, instead of Home Depot who could easily turn our dryer over to the insurance company as defective for the loss.

Mine is the same sad story as all the others. Bought our Maytag dishwasher in 2013 (model MDB7749) and 15 months later, the control panel went out. We have contacted Maytag and they basically told us it could be our fault it doesnt work, so they wont fix it. Now we have learned that this is an issue that A LOT of people are having. We called their special number for this problem and were told they still wouldnt fix it since we called BEFORE having it repaired. So my question is, how is this legal and why arent they recalling this product? I know that there was a class action lawsuit against Maytag for this problem. Why dont we hold them accountable as well? This is bad business and we shouldnt allow them to take advantage of hard working people like this.

Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

Both work good. Washer could be a little lower and it has quit rinsing and I cannot use it. But it is 9 years old, I think for their age they were a good buy. I plan to get the washer repaired because have been satisfied with how clean it gets my clothes and it washes pretty quick. I got the large capacity and with a very large load the washer gets them clean. The dryer is very good. It is just as good on a large load as small, dries quick. I would buy this type washer and dryer again and would definitely recommend it to folks. I have been very happy with this washer and dryer. The paint is coming off the washer where you put detergent and fabric softener in and it has rusted out some but it is getting a little age on it so this is expected. I like it, I can throw my comforter in and it gets it clean and the large loads always come out great. I think anyone who bought the set would be very happy with it. It is also quiet which I like.

I purchased a gas range from Lowes - Maytag- Model #MGR8880AS in 2012. The range has been repaired on multiple occasions 11/2016; 3/2017; 5/2017. All three times they replaced the igniter and burner. On one occasion they replaced the computer board as well. (Each time they have informed me that this part was a recalled problem and under warranty). The stove is now out of warranty and having same issue. The stove fills with gas and the igniter does not ignite and does so intermittently. Maytag only wants to send repair company out at my expense. They need to replace the stove, because someone somewhere will die because of their product. I will purchase a new stove and not from Maytag. (All my appliances are Maytag). I also have a copy of my receipt and will provide if needed; I used my extended warranty through Lowes each time. I urge everyone not to purchase Maytag appliances.

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

I purchased the Maytag oven in January and have had the service technician out 5 times to try to repair the oven because it doesnt heat properly. Theyve told me that because I live in a condominium that it is normal for the oven to take an hour to preheat, then another hour for the second oven to preheat. When I am baking the oven does not hold the temperature and anything I bake takes much longer than it should. They refuse to get me a new oven.

I dont know anything about the Maytag washers and dryers but have a Maytag washer and dryer. And I just recently bought a house that the owner is leaving both the washer/dryer, and both are Neptunes. I have an older set of Maytag washer/dryer and they are about 20 yrs old. They are both top load and I had one repair where a water line had a small leak and the service man came and fixed it and havent had any problems since. So I came on Maytags site to see how good these are, but from what I read, I think I will give the set of Neptunes away and just keep my old set as I am told them will last a good 35 or more years. They are heavy duty and large capacity. Thank you for letting me comment on your washers and dryers.

A pure piece of junk this wash machine is. It is more of a merry go round than a wash machine. I do not understand how it can be called energy efficient. All it does is spin and spin and clothes come out as beautifully dirty as they were loaded. If you make the mistake of putting a few extra clothes (machine calls itself a large capacity), clothes bunch up and one has to pull them apart. The bleach dispenser was used as one would use a bleach dispenser. However it is all rusted. I had bought extended warranty from Lowes but Lowes did not honor the warranty saying rust was a cosmetic issue. Yet when Lowes sold the extended warranty, they did not specify cosmetics were not covered. It is not even cosmetic. It simply is cheap enamel paint.I have used 200 dollar wash machines but never have I experienced such a horrible and annoying product. I will try one more time to see if Maytag will help out with the rust issue. If not, I will simply cut my losses and buy a regular cheap machine. Maytag should be ashamed of itself. I bought a Maytag because I thought they made the best machines!!! Oh! Well, maybe they did at one time.

Under no circumstances should anyone buy an MMV4205DE or maybe any Maytag microwave. These units contain defective door switches and will fail within a year rendering the unit useless. The engineer that got the bright idea to protect us from starting the microwave without opening and closing the door along with the engineer that designed the defective switch scheme should be fired immediately.I purchased the unit March 2016 to replace a 10-year-old Maytag that had a failed magnetron, no problems ever with the door switches! This unit started to act up in Dec 2016 with the fatal open/close door problem, I am an EE so I opened the unit and checked the switches and found they were defective, replaced both for $80 and 6 months later the problem is back. I am buying another brand as I dont have time to deal with the problems with this unit. I now have the old white 15-year-old unit that I replaced years ago sitting on the counter to use while another unit is on order. Unit is heading for the landfill next month. Never buy a Maytag microwave, they all have the same problems!!!

There was a maytag dishwasher in the house we bought 11 yrs ago. The only problem we have had is a recall on the rinse aid dispenser which was replaced by a service man but never worked again. We are completely satisfied with the operation of the unit, our only disappointment is the wire racks. The original racks plastic coating broke at the end nubs and became rusty and swollen. We found someone selling a unit and we just took the racks and left the unit for him to resell rackless. Unfortunately not two yrs later the same thing has happened to those racks. Even tried these little plastic covers that are made specifically for this problem. They were virtually impossible to get on and didn’t last more than a few months.

Updated on 10/09/2019: Well I wrote a review on my brand new Maytag washer that we bought at Lowes in June. When I wrote the last review I was waiting for our repair. They did come to repair and I was told by the repair guy (keep in mind the washer was only 2 months old at the time) that there were 3 fail codes. He said that it was overloaded or loaded wrong.That you cant wash towels with sheets, you cant wash any kind of rug no matter the size, which I only wash small bathroom rugs that are NOT oversized or heavy, you cant wash tennis shoes (which I have not). So I asked him what is the point of investing in what is supposed to be a top of the line, heavy duty, extra large tub, commercial washer? He said that you cant do that with any machine. I told him our old washer that we had 13 years had no problem with washing towels & sheets together. My point is that I am 100% disappointed in this washer & I encourage you to NOT buy Maytag, apparently they no longer live up to their brand.Original Review: We did our research & comparing & this machine came up on top. Its size suites our needs & we were excited about all the great features. We purchased it in mid July of 2019 so its 2 months old & for the last month it started to shut off in the middle of a wash cycle. At first we thought that maybe we were doing something wrong. So we would re-start it & it worked. Fast forward 3 weeks, it was doing it almost every time. Now it isnt working at all, it starts to fill up then shuts down before it starts to wash.Today is a Friday & I called Maytag to request a service call under the warranty (60 days old) Maytag had me on hold for 19 minutes before I could even talk to someone! The customer service person (once she was on) was very nice & sympathetic but couldnt get anyone out to service our machine until Tuesday, which is a HUGE inconvenience since we have not been able to wash for the last 3 days. I am highly disappointed in the machine for the simple reason that I paid for a new topnotch machine because my old one that 13 years old finally gave out & now am in the same situation & in for $1000 I paid for this new washer & having to go pay to do laundry 2 MONTHS later! I will add to my review once they have performed the service call to see if the issue is resolved or the machine replaced if they cant fix it.

I purchased the Neptune HE pair because they are front loading and can be set on pedestals to raise them to a comfortable working height, plus the brand and reputation are both excellent. I like that the chimes can be adjusted from low to high, or turned off. The front loading washers clean so much better and with a lot less damage to items than washers with center agitators. Looks are secondary, thats for sure. Functions like warm/warm cycles and being able to adjust to whatever load needs to be washed is really most important to me. Any appliances with a good, proven track record of reliability with few repairs is high on my list. Expensive appliances should be made to last and be of durable quality! No cheap plastic or weak-looking welds or components, thank you! Quiet operation and dependable cleaning and drying are top in my book, and this pair has exceeded even my picky expectations in total overall performance. They are 11 years old now and look & function like new! I had one minor repair on the washer at 5 years, and not a single problem since. With front loading washers, its important to keep the door open a little when not in use so that they dont get a musky smell. Ive gotten into the habit of using laundry boosters to help clothes, sheets, and towels smelling fresh longer, and putting a small amount in the washer drum has kept my whole laundry room smelling nice. Purchasing the pedestal drawers to set the washer and dryer on added extra storage to my laundry and its much easier for me to load/unload them at this comfortable height. Im totally spoiled by it now, so when I use someone elses laundry room (when I visit) I am reminded how nice my own setup is.

Bought a Maytag bravo xl washer and dryer two years ago. Spent around 1,500 dollars. Didnt make it a year before things started going bad on them. First the lid lock on the washer broke. I got the lid lock pulled out far enough that I could drill a hole in it and tie some thread to it to pull it out when the washer was ready to lock. Today the piece of junk just quit. Not long after the junk washer started messing up the dryer starts sounding like a fork in the garbage disposal. It still works and dries the close but you hate to even turn it on because of the noise. I will never purchase anything maytag again in my life. JUNK!

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

We purchased this microwave in Jan. 2012 to accompany a Maytag double oven for our kitchen remodel. Last night while using the microwave, 2 sparks shot up out of the top of the microwave and an electrical surge noise. I quickly un-plugged the appliance. The next day I attempted to use the microwave again and dense electrical smelling smoke poured from the top of the microwave, again un-plugged the machine. I have called an appliance repairman since the 1 year warranty is up. This machine is not even 2 years old and we will never again purchase a Maytag product. PS If the problem is the magnetron (whatever that is) I will contact Maytag for the warranty information.

Consumers be aware! Anyone who’s considering purchasing a Maytag Appliance I would highly suggest reconsidering! I bought a $2000+ Maytag fridge Model # MFT2776FEZ00 in March of 2017 and have had numerous repair calls on it: Several for ice maker not make ice, ice freezing in the bucket into 1 big CHUNK, water running down front of door on the inside and outside, to not working at all and ice maker needing to be replaced. Several calls for fridge not properly cooling (temperature was set at 37 degrees F but the temperature in the fridge is 55 degrees F - per 2 thermometers), food is spoiling. The back inside of “Temp Controlled Pantry” is freezing everything and whole back wall behind the drawer is frozen with 1-2” of frost and ice. Defroster is not working and again parts being ordered to repair an obvious issue with this model.I contacted Maytag and their response was “sorry, we can document the problem.” They will do nothing more! These Appliance companies are ripping off the consumers! Everyone passes the buck! Repairman says, contact the Appliance store you purchased it from, Appliance store says, contact Maytag, Maytag says it’s the repair companys issue.

I read some of the reviews on the Maytag ovens. I too have the same problems! Have had control panel replaced and still have to set at 400 if I need to bake at 350. It also takes forever to preheat. Trust this review because I am one very unhappy consumer!! DO NOT buy Maytag!!

Dishwasher control board has completely started blinking cancel when not touching it, ran for the entire time I was in Church. Numerous problems, only 2 years old. NEVER would I recommend this brand, EVER!!!

Because of the power of advertising, we replaced every appliance in our home in 2005 with Maytags. Since then, weve had minor problems with the stove and dryer, many problems with the dishwasher and washing machine, and complete failure of two Maytag microwaves, the last one was only two years old. The washing machine failures resulted in major flood damage two separate times due to two separate failures. Our refrigerator, model MBB2256GEW, has yet to let us down, however, since new it makes loud snapping noises that wake us up at night. It sounds like someone banging two large sticks together. Fortunately, I can repair most of these issues when they arise, but Id much rather get some rest like the Maytag repair man...

We purchased a Maytag Bravos Quiet Series 300 in June 09. The dryer timer has malfunctioned since shortly after purchase, it will add time near the end of the cycle, sometimes as much as an hour or more. We have had factory authorized repair firms (tried several) attempt to fix the problem both during the original warranty and extended warranty periods. They replaced the mother board twice and the moisture sensor on another occasion. All to no avail. Maytag has been worse than useless in the whole situation, and now will do nothing. It seems our only choice is to live with it, keep replacing parts, hasnt helped yet, or buy a new dryer. You can bet it will not be a Maytag!This situation is dangerous, if left unattended when the malfunction occurs the clothes and interior of the dryer get extremely hot. It is a potential fire hazard.

I purchased my Bravos (ecoconserve) washing machine in 8/2013 from hhgreg. The problem I have is this grinding noise with the spin cycle. So I unplug the machine because the lock lid light is flashing and wont unlock unless I unplug the machine. I grew up on Maytag so that was the reason I purchased this machine but never again. I am so disappointed in this product. :(

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

MDB8959SBB. Purchased this Maytag dishwasher late December 2013 and had it professionally installed on January 4, 2014. Could have burned down the house this weekend! Smoke everywhere! Thank goodness it was running during the day and not night so that we were able to shut off the power. Lights in the kitchen were blinking and smoke pouring out of the dishwasher. The house still smells of smoke. So disappointing. Ive always been a proud owner of the Maytag products. Never again. Especially after reading the reviews. Interesting enough, THIS dishwasher was purchased because of a recall on the PREVIOUS Maytag dishwasher I had trouble with. They gave me a credit to use towards my next purchase. Ive learned my lesson.

We purchased a new Maytag dishwasher last year when we purchased our new home. All the other appliances were Whirlpool. This dishwasher runs forever. We have huge electric bills and I am sure this is a contributing factor. We purchased it from Lowes. They have sent out two technicians who say there is nothing wrong with it. One said it was because it was in an island. The other that our water is not hot enough. He turned the water heat up and now you have to warn people using it to be careful or they will get burned. No wonder the Maytag repairman is so bored. He knows the appliances he services are junk and doesnt bother. Take my advice. Buy ANYTHING BUT Maytag!

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

Maytag washer MVWC565FW - Clothes do not wash. They just get pushed around and the soap scum is left on the clothes even with the water at the highest level. I bought the washer override lid switch at a appliance parts store just to observe the washer cycles. The washer did not wash the clothes. I took the washer back. I like Maytag products but this washer has to be engineered.

I bought Maytag Bravos X in 2014. I bought a set. The dryer is fine. Right after the warranty was up the washer started having problems. Maytag was no help. One sensor after another went bad. Now I have to unplug it to get it to start and then again to get it to spin. It hasnt spun on its own since 2015. It just recently wont start on its own. I have appliance repair people out and they cant fix it. They say everyone has problems with them. My mother swore by Maytags and had a set for twenty years or so, but now they are garbage.

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

We purchased a Maytag front-load washer and dryer in October 2010. In March 2011, all bearings and the drum needed replacement. In July 2011, the pump needed service and now in Sept 2011, we were told a new drum and bearings are needed again. The washer is still under warranty by Maytag. We contacted Maytag to ask for an exchange or a refund but we were told that it wasnt possible.

I purchased the Maytag double-oven gas range, Model MGT8775XS, in 2013. The quality of this double-oven stove cannot be understated. Performance? Terrible. Reliability? Awful. My experience was shocking because when I was a kid, Maytag was the ideal for quality and reliability. Those days are over. When delivered in 2013, the ovens did not work. Heating went to 200 degrees and stopped. During the next three years, we had this Maytag stove repaired four times. The most recent repair was in October 2016. A new regulator and igniter cost us $360. Four weeks later you guessed it the ovens stopped working yet again. We sent the Maytag stove to the recycle dump. Its far more valuable as scrap metal.

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

I could not get parts for Maytag Model MHWE200XW00 Type 832A as the Whirlpool does not provide after sales service. I purchased the new washer in 2010 and lasted for just 4 years. I believe they guarantee supply of spare parts (Inner Basket, Outer Tub and Rubber Boot) for 10 years and more.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

I purchased this washer because of Maytags reputation of the repairman who was supposed to be needed less. Ha! Was that a joke? Ive only had this washer 5 years, repaired once and now it sounds like its gonna blow up. Please dont buy one… Maytag has a one year warranty, but unfortunately I didnt take one out due to their reputation. Plus its hard on the working class to come up with the extra for the extended warranty! I dont normally write reviews but thought maybe I could save someone else a little cash!

The new Maytag commercial brand is different than the traditional Maytags. Uses less water. The new technology in the variety of choices for cycles and the steam cleaning for the dryer is a great feature.

Maytag Centennial commercial technology washer - Bought what I thought would be a great washer given the Maytag brand about 3 years ago. Started out ok But has gotten progressively louder and noisier. We cant even hear the television on the next floor of the house when the washer is running ridiculous. Now it wont work at all. Outside of warranty and a real pain. Not sure what to do but if I have to buy a new one its not going to be Ay

This is not about a Bravo but Maytag is the biggest piece of junk Ive ever owned. Have not had the washer but a couple of years and is leaking somewhere inside of the machine. Have to turn the water on and off just to wash clothes and still laundry room floor soaked. The dryer I have to run for 70 mins. on high heat at least twice to dry clothes, 3 times for your towels. Of course it lasted long enough so the warranty had run out. Never ever again would I buy this crap.

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

This is the best microwave that we have ever purchased. I especially like the baked potato choice. Its also very easy to use and clean. I would definitely recommend it.

I bought this Maytag dishwasher model mdb6709awq1 from Home Depot that installed it; they did a good job installing for a fair price. My gripe is with Maytag. I have owned a Maytag dishwasher since 1977. Back then it was the best you could buy. Since Maytag sold out to Whirlpool to save being bought by the Chinese, the design of the dishwasher has lost or gave up their unique design that made it so good and dependable. The inside of the rack/drawers has been totally changed. It used to have fold down racks on each side of bottom rack that was great for coffee mugs, small bowls/containers, and they came out sparkling clean. The utensil basket was centered front and again the utensils came out super clean. Maytag sold their soul when they sold out to Whirlpool. Dont know if that was part of the deal that they give up their unique design or why did they change the rack design. I wish I still had my old Maytag from 1998 that yes, worked without a problem, then I sold the house with the dishwasher. Why is it that so many appliance makers have taken dependable workhorse designs and phased them out? What is wrong with an appliance lasting for years, decades without problems? Only thing I can think of is that they wont make millions every year as they only would sell so many a year if they are dependable as they wont need to be replaced.

We bought this Maytag Bravos XL machine in Sept 2016. It has never cleaned the clothes properly, you cant even tell they have been washed! It also shakes a lot. In January it shook so much it knocked a hose off, flooded my kitchen and downstairs bedroom. Home insurance had to pay to replace the kitchen floor and downstairs ceiling. We contacted Maytag. They said they dont have a repair person in our area. Home Depot wont take it back. We are stuck with no workable machine. We have to go to the laundromat and pay 70 a week for laundry, plus the time, and we are out all the money. We paid Home Depot (thousands) for a washer and matching dryer. Plus all the takeout we had to order while they repaired the kitchen, but the strain of this whole thing is ridiculous.

I purchased a Maytag Bravos XL Commercial Technology top loading washer, model # MVWB850YWO, in May 2012 and it was delivered in August 2012 due to a home purchase not being consummated. Anyway, I bought this washer and the matching dryer at Lowes and purchased a 4 year extended warranty with Lowes. This would cover me with a warranty through August 2017. I had some problems with the washer while under warranty and had it repaired at least twice. I have had, and still do, have a water leakage in the washer. The water when dispensing into the detergent compartment splashes over and you would think it would just go into the tub. Someway the water leaks down the inside of the washer and runs out onto the floor also causing rust to the inside of the front panel. The resolution was to turn the water pressure down on the supply lines. When this was done, the washer would quit running due to not enough water being dispersed into the drum. A replacement seal was installed and I still have the same problem. The repairmans final resolution was to put tape over half of the detergent dispenser to hold the water in the detergent dispenser and still allow me to put detergent in the dispenser. So, a towel is in front of the washer to soak up any leakage. Now, just 5 months after the extended warranty expired, the bearings under the wash tub are starting to roar during the spin cycle. I contacted Lowes service again and basically I am out of luck. The repair cost is expensive, the part and requires 2-3 hours of labor. I decided to chuck this washer and buy a new one. My wife found one that has an agitator, unfortunately another Maytag, and wants it as she has said the Bravos washer never seemed to get the clothes clean (due to not having an agitator). When checking online for references on a new washer and any recalls on my current washer, I discovered other Bravos XL owners having the same problem with the bearings in the tub. I contacted a local business to try and sell it to him for cheap and when I told him what was wrong with my washer his reply was, I have one just like it out back with the same problem. Dont need two problems. Cant even get rid of a Maytag washer due to it being junk. Many other reviews have listed problems with Maytag products especially since Whirlpool bought them. The Maytags of today are not your parents Maytag. Used to be the Maytag repairman sat around his office waiting for repair calls. This has changed considerably since Maytag sold out to Whirlpool. After doing some research, it seems Whirlpool has bought just about every company selling washers and dryers and are making them as a disposable item. I would advise not purchasing any product that is under the Whirlpool corporate umbrella as I feel whatever they buy, even a superior product like Maytag, they cheapen the product and try to benefit from the name, as in the case with Maytag. So, no more Maytag or Whirlpool products for me until they have proven they can build a quality product once again. Hello GE!!!!