My complaint is not against Home Depot but Maytag Products. They are inferior products. Stay away from Maytag! Note: We are in our mid-to late 60s, no kids using these products and they do not get a lot of wear and tear. Maytag Microwave: MMV 4205DS-0, May 29, 2014 we purchased Maytag appliances for our kitchen (stove and microwave from Home Depot). I liked the 10 year metal warranty plate attached to the front limited warranty of the microwave. This means nothing! They cover the stainless cavity of the microwave (a part that will never go bad). June 3, 2014 this microwave was delivered. Thanksgiving, the microwave went out November 30, 2015 this was replaced with GE Profile Model JVM3160RFSS for $178. November 30, 2015, Diamond Factory Service was here for the Microwave. We paid $90 for the service call. They wanted $228.09 to repair (1-8206419 Switch $15.22; 1 W10269460 Switch $27.03; 1 W10727360 Microswitch $27.03 and Labor $155.00). Maytag Dishwasher MDB7749AWM. Purchased from Al race Appliance for $599.95 total with tag etc was $920.27 on 5/16/12. So thankful was purchased the additional warranty for five years. We have had 2 service calls so far for the same issue, which is W10356494 Console CMFF0312434. This is a known problem (it will not start). I wish I would have googled the model before purchase was made. When the warranty expires, this will go to the curb too.Also, purchased Maytag Neptune Washer and Dryer from Best Maytag, Rockford. The dryer had problems with the circuit board after a short time. Too expensive to replace. Our family and friends ALWAYS purchased Maytag only. No more! Stay away! We are waiting for the oven to go next. Oh and check out the bottom drawer. There use to be room for pots and pans. No more. Lucky to get your pot holders in there.

On February 2006, I purchased a Maytag Quiet Series 300 Dishwasher and on July 2007, a motor leak. Maytag fixed it for free even though it was out of warranty. Thereafter (December 2008), the touch pad failed and I replaced it for $50. It is now August 2011, and that new touch pad is bad again, and this time, the part is $170. The Maytag will not run and the lighted display will not function from the start button. This was a $450 dishwasher that is now only five years old and useless.In all fairness to Maytag, their customer service is very good and willing to work with customers. Unfortunately, the product is very inferior in my opinion. To have stupid stuff like a control touch pad failing every three years is absurd and the replacement cost makes fixing it a bad investment.I will be going out this weekend and buying a brand-new inexpensive dishwasher that is on sale for $229. This model is not a Whirlpool product but it is a name brand.

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

Maytag Bravos XL HE MVWB725BW. Washer was fantastic at first. Then about at 14 months old, the spin cycle starting making loud noises. Called Maytag, they promptly dispatched a repair service. The estimate to fix the washer was $531. The repair man stated Maytag does NOT seal the bearings from the factory. They only rely on a rubber washer, poor design. Maytag was unwilling to help with a washer with their name on it that failed at 14 months in any shape or fashion. She mentioned that Maytag has a 2-10 warranty on the motor only (which is non-existent, its electromagnetic). This will be the last Maytag that I ever intend to purchase.

I related my problems with a Maytag Bravos Washer a few days ago. A year and a half after I purchased the washer, it would no longer spin, among other problems. I was persuaded to call a repairman who diagnosed faulty electronic components which would cost me nearly $400 to repair. He confirmed that the washer was poorly built and strongly advised that I replace it. So, after paying him only $25 for a service call (he felt sorry for me), I did some research and bought a top-load agitator washer because the old-fashioned machines actually do their job - they wash clothes! I was duped by the high-efficiency claims, low-water-usage of the Maytag which didnt wash that well when it did work.

Purchased a non agitator washer 1 year ago. Constant frustration with the sensing technology. Cannot select a water level or load size. The expectation is that the machine will do that automatically. The water dispenses through the soap container adding soap to dry clothes which then leave white marks on dark clothes. All of the selections for loads do not have a water level close to covering the clothes. The only way to achieve coverage is to reopen the lid multiple times to restart the sensing feature. Another option is to add wet clothes to increase the weight to “fool” the sensor. Some clothes have come out of the wash still dry in areas. Every load, no matter what size takes a full hour to complete! There is no quick load to be done! I have paused the cycle to leave the house and the water drains from the machine causing you to begin your 1 hour cycle again. Epic fail by the Engineers to provide a user friendly machine. This one, as time goes on, just becomes more frustrating and yes very noisy during the spin cycle.

I bought the dryer (Maytag Gas Bravo Dryer) from Home depot in December of 2010. The thermostat went out in July of 2011 and has replaced the same part 5 times up until August of 2011. Then they put a new burner with a thermostat and it lasted till June 1 of 2012. Now the warranty is out, they want me to repair this piece of **. I will never buy a Maytag product again.

Bought Maytag dishwasher 2007 at Lowes. Model mdbtt60aww-37837606ll manufactured in Benton harbor, Michigan. First got a recall that something was faulty, could cause fire, needed replacement. Took 2/3 weeks to get repaired. So couldnt use. Never quite cleaned good - many times had to rewash silverware, glasses. Never took off food unless very well rinsed. Today the control panel went. Called a local repair he said, Dont even fix. Toss and get a new one because its too costly to repair. I asked what should I get. He said no GE, they are getting out of appliances, no Samsung. Hes got whirlpool so guess Ill give that a try. In the past Ive had dishwashers 20 years, appliances 20 years. This junk lasts a year or two. Plastic cracks. None of these appliances are great anymore. Doesnt matter who you buy. Someone needs to get some quality control on what these companies are peddling .

The freezer will frost up and the shelves will not move. Repairman has been out three times, once to clean the drain. The second time he installed new tracks for 250.00. Two hours later they still wont move. The third time out he said it was repaired, but two hours later they didnt move again. We are very disappointed with Maytag.

A pure piece of junk this wash machine is. It is more of a merry go round than a wash machine. I do not understand how it can be called energy efficient. All it does is spin and spin and clothes come out as beautifully dirty as they were loaded. If you make the mistake of putting a few extra clothes (machine calls itself a large capacity), clothes bunch up and one has to pull them apart. The bleach dispenser was used as one would use a bleach dispenser. However it is all rusted. I had bought extended warranty from Lowes but Lowes did not honor the warranty saying rust was a cosmetic issue. Yet when Lowes sold the extended warranty, they did not specify cosmetics were not covered. It is not even cosmetic. It simply is cheap enamel paint.I have used 200 dollar wash machines but never have I experienced such a horrible and annoying product. I will try one more time to see if Maytag will help out with the rust issue. If not, I will simply cut my losses and buy a regular cheap machine. Maytag should be ashamed of itself. I bought a Maytag because I thought they made the best machines!!! Oh! Well, maybe they did at one time.

Bought this Maytag washer from Sears and the salesman told us it was the best washer on the market. Well the Maytag washer is a dud. It leave residue on clothes, clothes come out very wrinkle. This washer does not even have a filter. I would not recommend this washer to anyone. We are very dissatisfied. We dont blame Sears, we blame Maytag for even thinking about putting this washer on the market - Maytag model mav7757aww

Our control panel just went out...purchased in November 2015. From reading reviews it appears our only option is to purchase a new control panel and hope for another two years. Ours (MDB7749SBM3 Dishwasher) was purchased from Sears and was not cheap. When is Maytag going to recall this panel? I read reviews that this problem goes back to 2011.

I also bought a Maytag Neptune MAH5500BWW and matching dryer model #MDG5500AWW in 2001 and within a month, I called Sears and Maytag. I told them about the terrible odor and mold growing. The repairman said it is normal and told me to use Tide detergent once every two weeks. The dryer had a major breakdown and I had to buy a whole header with all the electrical components. I too bought the brand name Maytag due to a good reputation that Maytag had. I never received a recall notice or anything from Maytag. I will never buy Maytag products again. I found out from a salesperson at Sears that Maytag was sold to Whirlpool. The salesperson said the reviews are terrible for Maytag products especially for my models. I will never buy from Sears, etc. What can you do for me? Maytag and Whirlpool need to take their responsibility for their products! I am truly lucky I did not buy a plane from them. I and a lot of people would be dead.

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

Mine is the same sad story as all the others. Bought our Maytag dishwasher in 2013 (model MDB7749) and 15 months later, the control panel went out. We have contacted Maytag and they basically told us it could be our fault it doesnt work, so they wont fix it. Now we have learned that this is an issue that A LOT of people are having. We called their special number for this problem and were told they still wouldnt fix it since we called BEFORE having it repaired. So my question is, how is this legal and why arent they recalling this product? I know that there was a class action lawsuit against Maytag for this problem. Why dont we hold them accountable as well? This is bad business and we shouldnt allow them to take advantage of hard working people like this.

We purchased a Bravo Maytag series top load washer from Sears in June 22nd 2013. See receipt for verification of sale. It seemed to be alright and we were hoping to be a lucky consumer, but now it is January 2015 and today I could smell smoke along with a weird smell (like an auto repair shop smell). I immediately was concerned about the entire house catching fire. Luckily I figured out the smell was coming from the washer and was able to pause it, stop, and then turn off. We are not happy. Our whole main level smells awful. And Im pregnant so this is probably not good to be inhaling. We are looking for recalls that may be out but weve only seen front load recalls not top loaders. When we bought this it had great reviews, but now it appears there are so many complaints, so my question is: Why isnt Maytag doing something about this massive problem?

I grew up trusting and believing in the name brand Maytag. Unfortunately, I wont anymore. I purchased a Maytag MDB7749AWM1 dishwasher from Lowes thinking that I would not need the extended warranty because well it was a Maytag and they just keep working and working for years to come. Not true anymore. 1.5 years after the purchase the control board has gone out. I come to find that hundreds upon hundreds of people have all experienced the same thing. Shortly after the manufacturer warranty expires, the panel dies. By all accounts it is an issue of POOR engineering and Maytag now being produced by Whirlpool. The replacement part is between $150 and $200. Thats about half the purchase price. It is a racket. Companies like this probably think, well if we build something that is going to last and last we cant make money on that. So lets rig it so our stuff breaks right after the warranty and charge half the price of the unit to fix it so we continue to make money either by people buying the part or just going and getting a new dishwasher. Well I can tell you I will be getting a new dishwasher and it certainly wont be a Maytag OR a Whirlpool.

My Maytag dishwasher Model No. MDB7759AWS1 caught on fire last night, inside the control panel on the top of the door. This was very alarming as it filled the house with smoke and caused some fire damage on the bottom of the countertop also. This could have easily caused a house fire and is very disturbing. When I called Maytag, they say this model is not recalled. In my opinion it needs to be. This is a huge accident waiting to happen in other peoples homes. Please beware. If the countertop would have caught on fire entirely, the house would have gone up in flames.

Just like all the other reviews, the control panel on our 3-year-old dishwasher stopped working. The obvious defect of the product and lack of customer support is unreal. We ended up replacing the Maytag with a Frigidaire. Hopefully it lasts more than three years.

We purchased the Bravos XL Washer (top loader) and dryer about a year ago and have had issues with it since it was installed. Please note, we live between two homes so the machines are not heavily used at all. Our $250 machine we have in our Florida home works a million times better and is several years old. We purchased at the ABC appliance store and they have sent out a technician 4 times in the first few months. Bottom line, these are just pieces of crap machines. They cannot be returned! It is really a shame for the money spent and your clothes does not get clean on any cycle. The technician told us we should use the Deep water wash for all cycles which still does not work. I bought this machine for the XL capacity but also for the delicate cycle and stains do not come out, undergarments are still dirty, white power residue from OXI is left on the clothes etc... DO NOT BUY. This would get zero stars if I could. So disappointing and frustrating. If class action suit does happen, I would want to be part if it.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

I purchased this dishwasher at least 12 years ago and it still works. However, after that much use some of the buttons no longer work. It has china, economy, regular, rinse only and extreme wash features.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

I purchased a small (14.5 cubic feet) refrigerator for my basement from Home Depot on January 26, 2013. It was delivered on January 30, 2013. On February 14, 2013, we found that it was not cooling like it was supposed to. The soft drinks in it were not cold. I called Home Depot and was told I had to call Maytag for a repairman to come out. Since it was so new, I felt it should be replaced. They disagree. The warranty only calls for repair. So a repairman came out on Feb. 19th. He said that it has no freon. He doesnt know why. It could have a leak. It could have leaked out in the warehouse. There is no way to know this. He said another repairman would be out to fix it on the 20th. On the 20th, no one showed up or called. I called the repair company, S & S Appliance of Bessemer. I was told the repairman that I needed is in Montgomery today and the repairman yesterday was told to tell me he would call me. He was told to not tell me someone would be out today. So now, I have to wait until tomorrow for someone else to call me and see when he can fit me in his schedule. I think Maytag has a problem with their refrigerators. I think Home Depot has a problem not standing behind what they sell. I think S & S has a problem with their servicemen. I am not happy with any of these companies and will never buy another Maytag refrigerator or washer, but thats another story.

My boyfriend and I just recently purchased a Maytag brand washer and dryer set. So far, we are thrilled with our purchase. We got front load units that have an XL barrel so we can use it to wash comforters and larger loads. I have washed many loads and so far, havent noticed a longer time to wash or any issues. I love the fact that my clothes are all getting equally as clean and I can be sure that my items will not be torn or ripped in the process. I would recommend this product to anyone.

I have had this dishwasher for 3 1/2 years. Replaced the touchpad 2 years ago and now the touchpad is dead. I read all the other comments that are similar to mine and am thinking to replace this junk dishwasher. I will not be buying from Home Depot as they are selling cheap products that are defective!

My name is Luis ** and I own a Laundromat in Yuma, AZ. I recently purchased 10 Maytag top loaders model MVW18PDAWW in August, so the machines are practically new. They are the new HE top loaders with locking lids. Since I purchased them I have had nothing but trouble. Customers have complained about them on a regular basis; there are days when we have had as many as five complaints.First of all, the locking lids proved to be a much bigger problem than we anticipated. People want to open top loaders to add fabric softeners and when we have opened them so that they can add the fabric softener they are often disappointed with the level of water in the washer. Those people consequently refused to use those particular washers. People have pressed the buttons on the control boards and sent the machines into a loop; different readings have appeared on the screen. Some of them say out of order, sync and several other error codes. Eventually the machines reset themselves or I have had to reset the programming. In the meantime the people pass the word and those machines are not used by those who hear. The controls are too sensitive and are not suited to a commercial coin laundry.Whenever any buttons on the control board are pressed the time of the wash appears on the board. Because of this some people who are busy and are using and loading several washers claim that they have already put their money into the machines; they argue with the attendant or with us. Many times they actually believe that they have placed money in the machine and many times they try to get a free wash from us. Either way they are unhappy and they, and those who hear them argue, will not use those washers again. In most cases we lose them as customers and once customers are lost they never return.I placed them in a location where the previous Maytags had been heavily used, expecting them to replace the old machine. I was wrong. They are used very little and the long and short of it is that we are losing money and since our busy season is coming up, will be losing even more customers and therefore more money. I spent close to $12,000 on the machines, including delivery and installation and right now they are quickly becoming heavy paper weights. I have contacted the salesman who sold them to us, but he has given us the runaround and done nothing about the situation.

Read MANY complaints about these units leaking water onto the floor underneath. This is accompanied by a sheet of ice forming on the bottom of the freezer under the main drawer. Good money says the cause is a plugged drain tube. I had a Subzero that suffered a similar problem. The factory installed drain tube was a flexible coil type and food particles would be easily caught, compromising water flow - leading to an ice plug and eventual evaporator ice-over. I replaced the factory tube with 1/4-inch rubber fuel line and the problem went away for good. With the Maytag units, if memory serves, access to the drain tube is from the back of the unit. You have to remove an access panel to get to it. There is typically a small removable rubber restrictor cap on the bottom of the tube; this is the most likely spot for a clog to form. Due to its design, IMO, clogging and ice-over will probably be a periodic thing. If you are really handy, you can do this maintenance thing yourself.

Product number MMV4205DS. Beautiful, felt solid. Right away when we would put in a time to cook and hit start, the thing would say Open Close Door. First we thought it was moisture, and we would wipe the seal, then lifting the door a little helped. A month might go by and we would repeat this process. I did a little research and found the microwave is known for this. After the warranty was up, it got worse. My husband put a little screwdriver in the door clamp. The plastic guard that held the door shut fell behind the opening. Mulling over whether to call for repairs or buy a new one, we decided the latter. I am buying another one just like it, because the holes in the wall will match for an easy swap and it matches my suite. This time I took out the 3 year warranty, which I will hold Maytag responsible for any more problems. They say if they come and fix it 4 times in a year they will declare it a lemon and replace. I figure this will work in my favor because the microwave lasts a year!

Our refrigerator is 2 years old and still under warranty. The ice maker had to be replaced. Now the water leaks on the floor. The deli drawer cover broke and when you get ice out of the ice dispenser it flies all over and goes on the floor. Our dealer has been fairly helpful.

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

I have bought a new Home Depot Maytag Impeller HE washer. After 6 repeat washings of 2 items that are lightweight dark brown it was obvious after drying they had soap and lint and lot hairs on it. I reached with no he detergent. The last 4 times the water level filled to 1 depth even for high level water setting to extra rinse or power wash settings. I went to Home Depot and they suggested I call Maytag repair center on Tuesday after the labor day holiday to have them check it out. I will also call the supervisor at Home Depot as I do not feel paying $600 for a faulty machine is acceptable.

I bought a new refrigerator and when I plugged it in would not cool. I called and the authorized tech came and said the compressor was bad and the evaporator was rusted and hoses were greased up. I have now been informed that the warranty was void because it was put in a dental office and not a single home. I said since it was never used I would put it in a house. They said it was void and I was out of luck. I always thought maytag sold good products but this has convinced me to never buy a product from them again. It never worked and the tech said it should be replaced but they said he should never had told us this.

Purchased Maytag 4000 series washer Feb. 26 2011 - within six months Maytag warranty replaced the drum and bearings, within another few months Maytag worked on the drum again. Year two started out with the warranty contract replace the drum and bearings again. Oct 1 2014 called for service again, the drum not moving and having to wait 2 weeks for Tech. to checkout the machine then order parts. I have 7 children at home and that didnt matter to anyone. After reading online the number of 4000 series Maytag machines with this problem somebody needs to make Maytag recall and replace them.

I purchased all Maytag products for my new home three years age. The dishwasher stopped working 13 months after we purchased it. Since the home was under renovations for the first month, we only actually used it for 12 months. When I called Maytag, they told me that it was either the control panel or mother board and that they could not do anything because the warranty was only for 1 year... and didnt offer me anything to make good on this...NOW three years later, my microwave is displaying error code SE.. control panel is bad. Now I have not had a working dishwasher for two years and this just added salt to my wound. I called Maytag furious that this keeps happening with new products. The only thing they would offer to do is for me to purchase an extended warranty at $350.00 and they would have a repair guy fix the microwave. A brand new microwave would cost the same thing???? They flat out told me that there was nothing that they would do for me, and that they were not going to fix it for free.I filed a complaint with them and never heard back from anyone at Maytag. It seems strange that the control panels craps out within one to three years on two of the four Maytag products I purchased. I WILL NEVER BUY MAYTAG AGAIN... I went back to Home Depot and told them that MAYTAG has LOST me as a customer and that I purchased 4 major appliances from them and two stopped working with in 1 to 3 years. Home Depot was shocked and gave me $100.00 towards a new dishwasher. And I did not buy a Maytag.... I still do not have a working microwave... But when I do have the money to replace it, it will not be MAYTAG. Looking online, I notice a lot of the same complaints about Maytags control panels...... Could it be a scam on Maytags part???

I purchased the Maytag Bravos series washer and dryer recently. I love the dryer but the washer does not clean the clothes. I have to wash twice if I want it clean. It does not get the stains out and does not use enough water to rinse the clothes. It also does not use enough water to wash/clean the clothes. I ended up washing all the loads on bulky which fills the washer with water. It still doesnt agitate enough to get things clean. I am extremely disappointed in the Maytag product which I always thought was top of the line.

In the winter of 2007, we remodeled our kitchen and bought all new Maytag appliances. They cost a little more but we felt that we were getting a good quality product. Within months, the handle on the freezer became loose and I had to call for a repairman to tighten it. He told me we should buy the extended warranty because only a trained repairman could fix the handle. That turned out to be untrue thankfully because if it was true, I would have to call for repair at least once a month. The handle is constantly coming loose. A few months later, the microwave would turn on when the door was closed. I called repair as it was still under warranty. After he removed and replaced the door, I was told that we have to be careful when we close the microwave. There was nothing he could do to stop the problem. Approximately three years after we purchased the appliances, we had a problem with the dishwasher. We could only use one function; the others would not work. We were told by the technician that we got water into the door where the controls are and ruined the motherboard. I never heard anything so absurd. I have had a dishwasher in the same place for 25 years with no mishap. The cost of repair was $800. A few months later, we had a problem with the large burner on our cooktop. The outer coils heat up but the inner coils do not. I have yet to call for repair because I do not trust Maytag. Now, our microwave does not work. My husband used it to make popcorn with no problem. A little while later, I tried to heat a cup of coffee and it would not heat. The keypad works, the light comes on in the microwave but the motor does not run. Needless to say, we are very unhappy and will never buy another Maytag appliance. I wish I would have read the reviews before we purchased the appliances. Two of our friends had their kitchens remodeled at the same time we did and they have not had any problems with their appliances. But they didnt buy Maytag. I guess thats why.

A contractor purchased the Maytag MDB7609AWW2 dishwasher about two years ago. Sometimes it will start a load, but most times it will not. The light for high temp, heated dry and sanitize work, but the heavy, normal, light indicators will not light up. Im faced with either replacing the control board or control electronics. I was told Maytag is a quality product. I have not abused the product. The last dishwasher that I had lasted 10 years. I only purchased this one because of a remodel. I will most likely replace the control board since thats the defective part. It doesnt give me a good feeling about replacing the part since it’s obviously a defective part. I will consult Consumer Reports before purchasing another dishwasher.

I purchased my Maytag side by side Model No. MSB27C2XAM00 in August of 2013. Within a 2 Weeks the lettering was gone on the control panel for the ice and water dispenser. I contacted Maytag and they replaced it, but the next one did the same thing, and the next one! They replaced it three times and they have all done the same thing. Now they are refusing to do anything more because they say I must be using cleaner or something on the panel because I am the only one having an issue with this! I assure you I have not used any cleaner and there are only three people in my household so it doesnt even experience excessive usage! I know this problem isnt as extreme as some, but when you pay this much money for an appliance you would like to think it should last longer than this!

We purchased a Maytag MFI2670XEW6 french door/Bottom freezer refrigerator in July of 2012 through Home Depot and for the past 6 months have had to scrape ice off the bottom of freezer every 5 days or so to prevent water flowing on floor. I see so many exact complaints from people that I am just fuming! Cannot believe this company is not backing their products up with that issue. A recall should most definitely been done. I grew up believing Maytag was top of the line but I am wrong. I bought this to replace a 16 year old GE refrigerator (side by side) which I never had any problem with and now I regret not replacing it with another GE. I havent contacted the company yet as I thought I would check complaint reviews before I did that but it seems that the company is just treating their customers like dirt. To spend $2200 for a refrigerator and have problems within the first 3 years is unacceptable!!! They had better start going good on this problem or face the fact that they will no longer be in business a short time down the road. The best form of advertising is word of mouth and online reviews and it looks like they are going to lose a lot of customers with the direction they are taking.

I bought a new stainless steel Maytag refrigerator last year. It had a one-year warranty. Wouldnt you know, 14 months after my purchase, the icemaker stopped working. Did not take out the extended warranty, as I thought I had purchased a quality appliance. I contacted the store where I purchased it. Was told it would cost $150 to replace. I have a feeling this appliance wont last very long. Suffice it to say, I will never purchase another Maytag appliance.

We bought our refrigerator 14 months ago and it has a 10 yr limited parts warranty. Both the freezer and refrigerator quit working, right after we spent $600 in groceries. I called the warranty dept and the soonest they could get here to service it, was 9 days later cause they only go thru Diamond Preferred, to do the repairs. Then on the 9th day, Diamond Preferred calls to let us know that unfortunately, they cant get here to fix it until another 5 DAYS!! Two weeks with NO refrigerator and freezer, is ridiculous. They should pay another repair place to come out instead of just relying on the ONE!! Our food is now ruined, $600 worth. And to top it off, weve had to eat out costing us more money, and then once its finally fixed, we have to go buy more groceries. I will NEVER buy a Maytag appliance, ever again!

Bought a maytag dishwasher 04/12/2013...have been thru 2 control panels...Now installing a third...washer works great except for that!!! Model mdb8949sbb0.

In October of 2012 we bought a Maytag Refrigerator Model MFF2258VEM. In the spring and summer of 2014, we noticed puddling on our kitchen floor. We thought it was our dishwasher or sink since the $1800+ fridge was new, but couldnt find the problem. We travel a lot and are gone for extended periods. When we returned in winter of 2014, we discovered that there was substantial puddling and found a sheet of ice in the bottom of the freezer compartment. We did research and found that this is a common problem with all the bottom-freezer Maytag models, which then leak. We discovered that the leak had seeped into our kitchen sub-floor and was destroying all of our kitchen floor tile, causing cracking and breaking, a renovation of just a few years previous that cost a lot of money. There was NO problem with the floor until we put in this Maytag refrigerator. The remedy for the leaking is constant maintenance and a lot of work, totally ridiculous for a product that costs so much. I want to sue Maytag for both replacement of the refrigerator and the cost of replacement of my tile floor. Can someone please advise? Thank you.

Our Maytag Bravos is 4 years old. Settings are preset at the factory. Besides the glitches others have written, the hot water sensor INSIDE the machine has gone out. This means - no clothes can be washed on the hot setting, and the warm setting gives only lukewarm water. I have had more than one plumber look at the machine, and the consensus is...the internal sensor needs replacement. However, this machine being only 48 months old, I am debating whether or not just to buy a new machine. This is a HE washer, and I am very disappointed in its performance. This is the worst Maytag machine I have ever owned.

We purchased a Model MDB8949SAWO Maytag dishwasher in September 2012. The control panel failed in November 2015. We wrote a letter to Maytag (Whirlpool) expressing our disappointment and received a call from Maytag customer service. The Customer Service representative informed us because we contacted our local repair facility directly, no reimbursements would be provided. During a subsequent follow-up call, I was informed by the Customer Service representative that Maytag manufactures quality products and that no premature failures were occurring with Maytag dishwashers. The Customer Service Representative stated that we should have purchased an extended warranty which lends some support to the fact that Maytag dishwashers are essentially junk. Never again will we purchase any Whirlpool products.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

Five years ago made a major investment on new techno with this washer/dryer. This is an updated review. Since the beginning the washer causes awful water hammer. Tried using arrestors, they dont work. Clothes are stretched out. You need to bundle each piece of laundry! The wash takes forever. Top loader has lid lock, very inconvenient - Dryer is OK but needs extra drying time. Would not buy this washer...

We were excited to finally buy a new wash set and I always wanted the Neptune ones. I had owned a Maytag for 25 years through two children and a mechanic husband. I had every confidence in the new ones and expected at least the same service. Shortly after the warranty went, the machines both started to act up. The washer would stop in the middle of the cycles. The dryer wouldnt come on or wouldnt respond to the commands. We finally contacted the local repairman whom we have used for years. He came and gave us boo-hoos about these machines. He said they were trouble and we should have never have bought them. My husband figured it was the electronics in the control panel. The repairman said the parts would cost somewhere near $500.00 to $600.00 each and proceeded to try to sell us used ones for $2,000.00. We said we would try to get the bad parts and he even gave us the stock numbers? We went online and found new ones for half the price. We bought them and put them in and they persisted in doing the same things as before. Is this a runaround or what? Who is bilking who? Another great American rip-off. What can the public do?

Products spoiling even if set at recommended temperature. Hard to clean bottom freezer. Not happy with this configuration. Had to have repairmen in because of stopped up drain which I could not access to clean myself. Does not close completely at times.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

It went bad, then I called a technician who replaced the compressor. After a few months, it broke down again after I had bought new parts for it. I was very dissatisfied with how the refrigerator was built. I spent lots of money on it, and it wasnt worth it.

We purchased a Maytag Jet Clean Plus in August of 2013. Within 8 months the control panel stopped working. Though it was replaced by one of their technicians it now after 9 months is broke again. How can this be such a crappy product??? Over 800 dollars for a dishwasher to have to go out twice in less than 2 yrs is just wrong. The company needs to stand behind their products!!! I will never buy Maytag again and will advise anyone looking to not waste their money!!! VERY DISAPPOINTED!!!

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

We 19 years and gently used. The door latch broke. We purchased a used quiet series Maytag dishwasher and found that the door latch failed on this. I recently found over 600 complaints for the same problem. If you are receiving this many complaints and its one of your most frequent complaint, do you think its time for a redesign of the door latch mechanic is??? Or are you relying on your reputation and dont care about quality anymore?This is it for Maytag. Im glad we didnt buy a new Maytag because we would be stuck again with a crappy door latch. If you cant be bothered with fixing your door latch issues and you know that you have a long term problem here, you at least can send a new door handle kit to those of us who are complaining. Of course you wont do that. And the only recourse I have as a consumer is to tell others about the ongoing problem with your front door latch on my social media. Sadly, you are now only another crappy dishwasher with no real quality control. I bought several appliances from you because of your reputation for appliances that last. Seems that is now a myth.

I have spent a lot of effort leveling my machine, and my wife balances the load very carefully, but 10 times during a cycle, it will start slamming the tub around, so loud you can hear it from the street. I, like others in this forum, thought I was buying the best washer in the market, and paid extra for the Maytag name. It sounds like from the other complaints, that my problem is just the tip of the iceberg. It will cost me $200 to replace the suspension rods. I wouldnt mind paying the money, if I thought it would fix my problem. After reading about all of the other problems with the Bravos, I might just cut my losses, and get a new one. What a waste of $1,000.

We bought this he Maytag washing machine about 3 years ago. I have hated it from the start and should have put a review right away because it is a piece of cr#&. It does not save any energy because I have had to rewash loads because clothes come out still dirty, lint still on them, sometimes even dry spots on clothes. I did a wash today and chunks of HE detergent still in the clothes. I am rewashing a load right now. I now have to do a presoak hoping that will help the load come out cleaner. So dont waste any money on Maytags HE machines as I will never buy another one.Being an environmentally conscious person, I thought HE was the way to go but it doesnt save any energy when you have constantly run a laundry twice to get clothes clean. It also does not do a good job spinning as clothes are still very wet. I hate this machine and I am thinking about junking it even though it still runs. Very bad purchase.

Maytag Bravos 300 Electric Dryer - Purchased dryer 2011 and a computer part went out and Maytag wants $418.66 for a computer part. This dryer was used only 6 months a year. Poor attitude about repairing from Maytag and they would not do anything to make us happy with product. A dryer that goes out in 3 years is robbery. Maytag should repair and make customers happy but they just dont care. Anyone who buys a Maytag or Whirlpool product should have their heads examined. I tried to talk sense to Maytag representative but to no avail. I am now going to make sure all of southern Indiana knows of my problem with this product. Those who know me know I have the ability to contact thousands of southern Indiana and Louisville residents.

My daughter purchased this washer and matching dryer as a set from Lowes about 4 years ago. It was one of the few with an agitator and that is what she wanted. After using the washer for the first time she was very disappointed to find that the shortest cycle took over an hour and that the locking lid feature couldnt be bypassed. A few weeks ago the washer began gushing water onto the floor which flooded the basement below. She had purchased an extended warranty which was due to expire the following week.She called Lowes and scheduled a repairman. He finally came 2 weeks later and used the Internet to help him diagnose the problem!!! We could have done that. He decided that the control panel was only allowing the agitator to turn in one direction during the wash cycle. So essentially it was spinning a tub full of clothes and water causing lots of water to overflow the tub onto the floor. Needless-to-say he had to order a part and cant return for over 2 weeks to install it. IF this is even the problem! He also said he couldnt disable the locking lid feature! If my daughter had been able to open the lid when the problem started she would have known more about it.We are thankful her machine was under warranty but she will have been without a machine for almost 2 months when and if it is fixed. This is completely unsatisfactory for a gently used 4 year old washer. The dryer takes forever to dry also. If you are buying Maytag based on how long your grandmothers machine lasted, you will be disappointed! This washer caused so much damage we had to file a homeowners insurance claim!

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

Belt broke in inside under tub after 13 months $150. Now another year and I am getting an error message F51 and it stops washing. Im done. Old Maytag lasted 14 years. This is done in 2. Im not paying any more to have it fixed for whatever F51 is. Im cutting my losses now. Hate this machine the way it washes anyway. Always feel like its gonna take off for Mars to join Matt Damon. HA. I try to laugh to stop being mad. Dont buy these. It gets no stars. And after reading other reviews, it deserves none. Shame on this company! Ugh, its making me put a star rating. But I say none.

Hello, My recently purchased dishwasher has leaked water within less than half an hour of the fifth time to be used and showed error: F8E4, dishwasher model and SN are: Model: MDB4949SKZ. Serial # : FA3003347. Registered: 09/11/2021, Ive been calling Home Depot who in turn asked the installer to check the connection, and the latter advised and reported its a manufacturer issue. And calling Maytag for several times but no response or action. On-line service scheduling of Maytag is not working!!! And the live chat is not helping, as well. Now my dishwasher is not working since more than two weeks, knowing that it has been installed only a month ago.

We loved the YMMV4206 microwave - at first. After the warranty was over, we started having issues where we would put the food in the microwave and try to enter the time, wed get the message to open door and close door. Wed try that and for the next few months it would work. At the 18 month mark, thats all it would do, was tell us to open/close door. We ended up unplugging it and it has been unusable since before Christmas. When I call Maytag and related to the support staff our problem, they were of the attitude that it is out of warranty and we can send someone out to take a look at it - for $130 + HST without even repairing it, that would be to diagnose the problem that we already know, then we would have to wait for them to order the part and come back. Do Not Buy this product.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

We purchased a Maytag Bravos Washer and companion dryer in March 2018. I like to wash our king size bedding often and liked that this model had no agitator and could accompany the large loads. I am using the extra rinse constantly since I dont trust the amount of water (not) used. The dryer however, is worthless! No matter the garment or setting, everything comes out in a ball. Tshirts are twisted and wrinkled and half wet. I end up rewashing almost everything then being a guardian for the dryer---checking and rechecking every load. Maytag says sorry, its out of warranty. I absolutely hate these appliances!

I bought a Maytag Bravos washing machine from Lowes in Ocala in Feb 2017. It broke in March 2017. I was referred to a company called Fields Appliance in Orlando Fl. I scheduled a repair under warranty last Friday between 1-4 pm. No one showed up. No one called. I called and called and nothing. BEWARE.

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

The washer does not get the laundry clean. It never has. I use only HE soap. I have changed soaps several times and still no change. I have been very disappointed with it. Maytag has been advertised as a good washer but the Bravos is not.

I built my home and bought all Maytag appliances. The freezer and fridge knock on wood have been repair free. Replaced control panel on stove for 400.00$. Washer after 2nd repair had to replace 600.00$. Dryer repaired once 95.00$. Replaced dishwasher with a new Maytag. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. This is the 4th repair. I have paid for 2 repairs out of warranty. 380.00$ the last repair. I did request some help from Maytag. They said no... My dealer did only charge me for the parts.

I purchased this machine (MVWB765FW0) because I had a good experiences with Maytag in the past. There is a manufacture defect in this particular machine. If I were you, I would not buy it. I’ve lost two sets of bedsheets and my wife had a dress that she loved that got ripped up at the bottom between the agitator and the base of the machine. Maytag knows about the problem and does not have a solution.

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

How is this fair that only a couple of washers recalled...I knew of no recalls either...My old Kenmore top loader outdated by far. Guess I should have kept it.

I have owned two Maytag washers. Top load and front load. They have been the biggest piece of garbage I have ever purchased. My current front loader eats and destroys clothing. I have had to throw out numerous clothes as the machine simply destroys them. I have also had numerous problems with Maytag washers. The wiring is garbage. Couple yrs after purchase the washer shorted out. Im handy so I took it apart. Discovered a broken wire. I had to rewire a new connection with as. The wire used in manufacturing is so thin its line a strand of hair. Now it leaks under the drum. I had to place a container under the drum to collect the water. My other purchase was a top load. The lint was just a nightmare. Maytag sent me some contraption after numerous complaints that was suppose to assist in the collection of lint. Again, a piece of garbage. DONT BUY. Save your MONEY.

I have the same problem noted by the other posts. Water leaking on hardwood floor from the bottom of the freezer. Refrig is out of warranty. Also, the deli drawer is also broken. This is a $2000 refrigerator and the quality is terrible. Please contact me for class action suit inclusion.

I bought the Maytag Bravos XL 5.3 washer because it was advertised to conserve water and it was a good brand, but it was a horrible mistake to buy this washer. The washer barely uses any water to clean properly and it hardly moves any of the clothing. The only thing that does move is the clothes at the bottom while the clothes on the top stays still. After using it for a day, I decided to return it back to Home Depot where I bought it, but they did not accept it and told me to call Maytag to return it. I called and the person who answered gave me different numbers to call. After going through ten different numbers, I finally received someone that could help me and they told me that I could not return the washer. They told me that the only way to return it was if there was a mechanical problem with the washer. It is extremely frustrating because I paid over $800 on this washer and now Im stuck with this garbage because I cant return it. I recommend everyone to not buy this washer otherwise youll get the same problems I am getting. I have to manually stop the washer and move the clothes by hand.

We purchased a Maytag dishwasher, Model #MDB7749, in the belief that it was a quality product. Many initial reviews were positive. Unfortunately, that decision was a mistake. The washer is only three years old and the control panel has failed. We are unable to select wash cycles. It defaults to Auto Clean/Heated Dry only. The washer has been lightly used.An online search found numerous complaints for control panel problems with this Maytag dishwasher. Please check ConsumerAffairs, Amazon, or Maytags own Facebook (Maytag was forced to create the Facebook page in 2010 under a mandate from the Consumer Product Safety Commission after a recall of dishwashers for fire hazards) before making any decision to buy a Maytag/Whirlpool appliance. It would also be wise to purchase an extended warranty.Our Whirlpool clothes washer failed after 5 years (bearings + controls). We cant afford to replace a major appliance every three to five years. The estimated cost to repair the dishwasher is $300 - $400. Maytag/Whirlpool customer service is indifferent to helping its customers. Its disappointing to see a made in America company produce such poor quality products and not support them.

I purchased a new Maytag microwave from Lowes barely two years ago. The inner door frame is coming apart which makes the handle to open slack which means the microwave does not operate correctly because you have to open & close several times. I called Maytag. They said the one year warranty is over. Furthermore one of their authorize dealers want $200 for labor, parts is separate. I said I can purchase a new microwave for less which I intend to do but never MAYTAG again.

I bought this after having a Frigidaire for 40 years and was immediately disappointed upon installation. This OVEN, not a range, was smaller inside and a lot of new pans would not fit! I have replaced the burners and the bulb wiring several times. Would not buy another one!

I bought this washer on 6-29-14, should have returned it within my 30 days but kept thinking it will get better, NO. I actually like to use water to wash my clothes!! It doesnt even get all the clothes wet when using on the bulky/or any other setting. Very disappointed in Maytag!!! Washer for sale, very cheap even though I paid $500 with warranty.

These are the issues, Water level is ridiculous, clothes often have dry spots, I use only the high water level which is a joke. The tub bottom is very hard to reach because it is too deep even for a man with a long reach. The tub itself is about 16” deep but never fills more than 4” of water on the high water setting. Why such a deep wide tub when you can only put 4” of water? Cleaning is poor, the machine is very noisy, very. The worst machines we have ever purchased with ridiculous sensors, bells and whistles. The dryer takes forever to dry clothes and again the sensors are a joke. The high efficiency of the units means you work much longer for clothes that are wrinkled, spotted, less clean looking and sometimes damaged. Where is the savings? And don’t say hydro and water as the washer cleaner cost, wipes that out and more. We gave our 26 year old machines to Habitat, neither machine was ever serviced and were in perfect condition, they were Maytag. They have destroyed their name. So sorry we decided to modernize our laundry room.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

We paid for a brand new washer and dryer from Maytag/Whirlpool. Right on the machines it has stamped in a metal plate 10 year warranty. So at 4 years when my washer started screeching and smoking I called for service. Yes, there had been a leak that burned out something in the engine and the bearings were shot etc etc. But they have been back 3 times. Each time they lack some part. I first called them on July 29, 2020. Today is October 13, 2020. They have still not got the washer repaired. I need to do wash every day. We are a family. We also have a senior in her 80s. And dogs. I need to do wash every day. So for weeks I went to the laundromat. That cost a fortune. Then a couple of weeks ago I impulse bought a new washing machine. A Samsung. On sale. Doesnt match the Maytag dryer. And the old washing machine got moved out to the garage. Its the pandemic. I cant keep going to the laundromat. What good is a warranty if Maytag/Whirlpool always has excuses for why they dont have parts. Its the motor. The very basis of the machine. It took them 2 weeks just to look for one. You wouldnt believe the excuses they make when we talk. But I am really unhappy with the way it all worked out. What good is a repaired machine 3 months later than I needed it. I had to buy a new machine. Why didnt they just tell me to do that on day 1 so I could avoid the laundromat. Why are they spending so much money to basically repair everything in that washer when they could have just bought me the new machine. When is a warranty not a warranty at all, but just a big lie?

2 years ago I purchased a Maytag Washer & Gas Dryer. Unfortunately, I did not invest or believe in extended warranties. I believe in trying to buy quality products. The door on the washer would not open and 2 error codes were displayed. I was trying to add another piece of laundry and the washer had just started. I canceled the load, waited for the door lock light to go out, but the door would not open. The error codes began displaying E3 and F5. I immediately went to the Maytag website for a resolution. The suggestions did not work and was instructed to obtain service if they did not. I called for a service call for $35, but was told that the repair would be over $300 for parts and that was not including labor. The parts I needed were a control panel and a part for the door lock. This was not a Maytag Company service tech and he told me that this happens because the parts are plastic. Currently, besides a Maytag Washer & Dryer I have a microwave, stove, and dishwasher that are also Maytag. When I replace these appliances, I WILL NEVER BUY ANOTHER MAYTAG PRODUCT. I expect the quality and life of an appliance to be more than 2 years, without buying an extended warranty. When I told a friend what had happened with my Maytag Washer, she told me that she had a Maytag Washer broke down with a control panel problem, and she couldnt remember the other part. She informed me that her repair was over $500.

The machine runs and runs and runs and still the clothes come out dirty. Clothes are often not even wet all over. The Maytag HE water-saving washer is a terrible Hoax. The dryer also is faulty. It rolls the clothes into a big, undried ball of dirty clothes.

Our washing machine is 3 years old. About a year ago we started to see hairline cracks on the plastic lid in the bottom corners by the hinges. These have now become huge and pieces of plastic are breaking off every time we do a load of laundry. Maytag (under the Whirlpool brand) will not replace the lid for us. We paid $130 for a tech to come out and confirm what we already knew - that we need a new lid. And now the parts and labor will cost over $550. We have called customer service several times and spoken to a supervisor and the best they can offer us is to pay for the part which still leaves us to pay over $400 out of pocket to repair a $600 washing machine. This seems to be a common problem and is all over Google, yet Maytag is not willing to help their customers.

This is my first convection oven. It is a double oven and I am hooked for life. I love the smooth top and use the convection daily. The only small issue I have is that the touch buttons on the range are on the harder side to push. But other than that, I have owned this for 5 years or more and would only get the same type again if I had too.

We have had this washer/dryer stack up for about 2 years now. Not long after it was purchased from Best Buy, it started smelling like mold, even though we were doing everything possible to keep it ventilated. Best Buy employee said that service was not covered by the warranty that we purchased, so they suggested we YOUTUBE some ideas on how to get rid of the smell. They said it was a common complaint for front load washers. We have tried Affresh, hot water and bleach, hot water with vinegar and lavender, etc. Nothing is working. There is mold on the plastic inside the washer door and the stench is horrible now. You can smell it when you walk into our home. I believe that stench is the reason we are all having respiratory problems, allergies, etc. I just dont know what to do anymore. Really frustrating!! These appliances cost a lot of money.

I purchased a Maytag Dishwasher in April of 2011 - Ive had four control panels in that time and the panel gone again - in fact, one panel came out of the box nonfunctional (I counted that one as it was installed although the tech removed it when it quickly became apparently that it wasnt working). Ive got a complaint in to Maytag but I have low expectations as to a satisfactory conclusion. What Id like is for Maytag to buy this lemon back from me for around $400 - I paid nearly $600 (including installation). Again, I doubt this will happen. From my research online it appears that the control panel issue is a latent defect which Maytag knows about but either wont or cant figure out how to deal with it or correct it. I have a scan of the receipt which Ill see if I can upload later. I know about one class action lawsuit for CA residents. I wonder if its been expanded.

I have owned my Maytag Bravo Series less than a year. After 4 repair calls, I called again. The service department was rude and hung up on me. He accused me of destroying the washer on purpose. They are the worst company I have ever dealt with. DO NOT BUY Maytag products ever.

Washer knots clothes into unmanageable tangle. Poor rinse leaves soap scum unless rinse extra, thus not conserving water as appliance is supposed to do. Load easily becomes unbalanced and unable to restart machine if paused to rebalance load. Will never buy another Maytag washer or dryer.

Purchase brand new range a couple of months ago. Self-clean oven does NOT self-clean and leaves weird, flakes of something that stick to oven floor. Burners are inconsistent and difficult to control heat level. Take forever to get warm, and then either boil over or wont get warm enough. Purchased this with inheritance from my mother - how sad! Always had such faith in Maytag.

Whos up for a class action lawsuit against Maytag? I believe Maytag is making claims that are NOT true. I bought a new Maytag Bravos XL in Nov 2015. I asked the salesperson to point me to a deep water washing machine for Large loads. Salesperson sold me the Maytag Bravos XL MCT and made claims I would have 30% more water than the other washers. The sales pitch (according to Manufacture) is these smart machines have sensors that can detect how much water is needed. THIS IS NOT TRUE. My Maytag machine only gives me 1-2 inches of water on the normal and rinse cycles and maybe 4-5 inches on deep water cycle!!! Certainly not enough to cover clothes, towels or sheets. I immediately called Sears. Tech is basically being trained to tell consumers thats the way it is. This is the new future in washing machines. So, My recommendation - hire an attorney to get your money back!

We (husband and wife only - no kids) had our Maytag washer for 4.5 years and around year 3, the control panel would need to be reset by unplugging it and plugging it back in. That alone was an inconvenience. This time, the Control Loc light is lit and will not go out despite using all troubleshooting suggestions listed in the guide so the washer is not usable. 10 year warranty covers the drum. I say that is like getting a warranty on tires and when one goes flat, you are told it only covers the hubcap. I can only rate the unit as garbage. Model is 5500, front load. So much for Made in the USA.

I am not dissatisfied with hhgregg, but with Maytag products. I purchased the Maytag Centennial Top Load Washer and Maytag Centennial Dryer to match. I was a bit leery of the new energy star models that use he only type detergent, but decided that was the newest and greatest thing out, so how could it be wrong? For the past two months, I have been sooooo very disappointed in Maytag. Neither of these brand new machines are worthy of being considered brand new. The washer takes extremely too long to wash a normal load, too noisy, and has ruined several items of clothing, due to malfunctioning distribution of bleach, fabric softener released after clothes are through washing. There has also been several times that the load wash is complete and the clothes are not even wet (like they were never involved in a wash cycle). As for the dryer, you have to run it through two 40 minutes cycles to get the load of clothes completely dry, so much for energy-saving. This is my first complaint to anyone, but after reading several reviews on Maytags website, I am reassured I am not alone. There are hundreds of other dissatisfied consumers of this Maytag product. I will be writing a letter to Maytag, requesting a refund.

Fridge model # MSF25D2EAB00. I have had the fridge 3 years and 2/3 shelves have crumbled to pieces, the compressor has gone, the ice bucket crumbled, the ice maker stopped working, once ice maker was fixed it got stuck on crush, and now I am trying to order another shelf because it has also crumbled like the rest and this is in a household of 1 person! I am just getting the run around... I have been redirected to 3 different numbers now (800-344-1274, 866-368-6478, and 877-468-2371) and now I had a rude customer service rep so I asked if I could speak with someone else and I am now on eternal rot on hold. Pretty sure he didnt even transfer me and Im just sitting on hold on his line while he is laughing. Time to hang up and try again another day. #un**believableI was also told that if I purchased the extended warranty plan that it would cover the crappy shelves in the future so I did and now they are telling me it doesnt cover them and it only gives me a discount on them. MAYTAG YOU OWE ME A NEW FRIDGE... THIS ONE IS A LEMON! I have no clue what my order number is or where my receipt is at the moment but I could get a copy Im sure because I purchased it on my HomeDepot credit card so if you want it let me know and I will provide it to you then.

Echoing the sentiments of others on this site, I am deeply disappointed in Maytag brand appliances manufactured by the Whirlpool Corp. When, for the first time in my life, I was able to buy all brand new kitchen appliances, I didnt even consider any other brand but Maytag. This was based on many decades of using Maytag products and watching my mother use them. I come from a big family so our appliances got used hard, and the Maytag brand ones worked year after year, decade after decade with little or no maintenance. To put it quite frankly, my new Maytag products are junk. I could supply a whole laundry list of problems but, in the interest of space, will just tell about the latest. A couple of weeks ago the fake tin foil paint on my oven and burner knobs just started falling off, revealing cheap plastic underneath. When I called Maytag to complain, I was asked how I clean the knobs. I told them that when I clean the stove front I remove the knobs and drop them in warm water with a couple drops of Dawn dishwashing liquid for the few minutes it takes to clean and polish the stove front, and that I had been using this same procedure for 2 years. The rep. hemmed and hawed awhile and then went away to consult her database. When she returned she told me that one is not allowed to soak the knobs per the manual, and therefore she could not offer any help. She then generously offered to transfer me to the parts department, where the rep. informed me that replacements would cost $70 EACH, thats a total of $350 plus shipping for 5 cheap plastic knobs. WOW! What a deal! I tell everyone I meet NOT to buy any Maytag branded product, and to apply extreme skepticism before considering any Whirlpool product. (BTW - the last certified Maytag appliance repairman to come & fix one of the appliances essentially admitted they are junk.) Model #: MGR8775AS SN: R32810432.

The glass shelves stop 2 1/2 inches from the back of the refrigerator. Things keep falling down in back. I have a counter depth. Cant afford to lose any space. Freezer poorly designed for space compared to one I had before.

Maytag washer, dryer, oven, microwave over-the-range - all crapped out in four years. I will never buy or recommend Maytag. I believed them to be one of the best brands but apparently theyve learned a few too many shortcuts.