Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

Bought a Maytag Stainless Steel kitchen stove to upgrade my appliance before retirement. 14 months later the spring loaded hinge failed. A bad piece of engineering in the way of a retainer pin to hold the spring pressure tore out of its pressed metal hole. The hollow pin was fastened in place by a 3 fluted punch instead of with a proper rivet with a head. My local parts supplier had 10 on hand so you know they are aware of this. $70 and an hours labor and it is repaired. My local seller said, Too bad you didnt get the extended warranty. So much for Maytag dependability.

I wish I had never bought a Maytag refrigerator! Nothing but problems. The ice maker does not work, water leaked 3 times onto our wood floor. Finally, I disconnected the control panel so I have an ice/water dispenser that is useless just like the refrigerator. I dont think the Maytag man is sitting around from lack of work, maybe laziness. Dont buy a Maytag.

I have a Maytag side by side. In the first year, the ice maker failed and I had to replace it (in warranty/no charge). In the fifth year, the compressor failed (no warranty) and it hasnt been replaced. Since then, I have been looking at reviews and warranties of new refrigerators. The warranties (unless you want to pay $3,000+) are all one year limited. The reviews are scathing and it doesnt matter what brand. My question is, why dont you/we all get together and file a class action suit and demand millions in damages? Complaining wont get you anywhere with these people; however, hitting them in the pocket book will make them pay attention, especially if the penalty is severe enough.

I purchased a Maytag dishwasher on Nov. 5, 2013 from Freds Appliance. I had to have the control panel fixed twice and it failed again in June 1916. My stemware had a film on it and I either had to wash it by hand or rinse it in hot water and dry by hand. Thus I felt like how could my other dishes not have this film on them even though I faithfully used Finish. I have 2 daughters who live within a half mile of me and they did not have this trouble with their dishwashers. I always felt Maytag was a top brand, but I replaced my 3 year old Maytag with a Whirlpool that my daughter and her family of 4 used for 19 years. Guess what... my glasses come out sparkling without using Finish and they wash in half the time and are dry!

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

Bought this Maytag XL washer and dryer in September 2012. In January 2014, the washer stopped working. Service guy came out and said the electronics went out. Then in May 2014, the dryer died. The dryer door latch broke. Would not stay shut. 2 days later, the heating element went out. Again, the service man came out. This service man said that this model is subject to break downs. This Maytag is a piece of junk. I went out and bought a Whirlpool, which I had before. I would never buy a Maytag again. I paid over 2000.00 for this Maytag and it is the worst washer and dryer I have ever had. Apparently, the Maytag repairman needs to get his butt busy. I have the Maytag now on my sunporch, waiting for the junk man to come and get it.

I bought a refrigerator from Home Depot in July 2013. In late November 2014, I noticed water on the floor in front of the fridge. I called the Maytag customer service and reported the problem.. The customer service rep explained to me that Maytag discovered a design flaw in the part that allows the water to drain when going through the defrost cycle. I also called Home Depot. Their response was it was my problem because the fridge was out of warranty and I did not buy an extended warranty plan. After two more calls to Maytag, they scheduled a service appointment. The service repairman told me the same thing about the design flaw. I have the old part and the package the new part was in. The two parts are completely different. I requested that Maytag or Home Depot replace the fridge or give me credit for the amount I spent. Maytag is now saying there was not a design flaw and because of that, Home Depot refuses to replace the appliance. I will never buy another Maytag product or shop at Home Depot. The extended warranty is a way to place the responsibility directly on the consumer and eliminating the responsibility of the manufacturer and the store.

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.

Bought Bravos XL washer/dryer from Home Depot in November 2014; installed 12/8/14. First repair was in March 2015! Clean machine cycle quit working properly on 3rd attempt. Bearings were replaced, tub was replaced and main board was replaced all before May 2015. Wash load constantly becomes unbalanced if more than 3 bath towels are in the load or more than 2 pairs of jeans. Can not start a load of wash and leave home because the machine will start bouncing and rocking when unbalanced and will shut down after it tries to self-balance 3 times. You end up with a load of twisted up, totally wet mangled clothes. Maytag refused to replace the machine and Home Depot continues to sell this junk to unsuspecting buyers. Wish I had looked at reviews before I bought this model. Worst $1,200 Ive ever spent. I have always bought Maytag appliances--refrig, stove, dishwasher, microwave, other washers--but Maytag has lost me as a customer after this experience with them. Terrible design and poor customer service for not standing behind their products.

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

I attempted over and over just to swap out washing machines. I originally purchased a washer and dryer because of a defect in the top load they delivered. They talked me in to the frontload Neptune instead. Within months I started having daily reactions to mold and to my disgust found out it was from my washing machine. I begged to switch back to the top load I originally ordered and the store would not let me and referred me to Maytag who sent me some tablets and would help me no further. Apparently, the Maytag repairman wasnt lonely anymore if a product had to be manufactured and ready for complaint calls. Well I used the product. I used vinegar and baking soda. I have used hot water and bleach. I have left the door open to dry...It is the most cared for item in our family and the one that makes me ill literally. I cannot afford to buy a different one and would be interested to know if my husband’s declining health issues have anything to do with our mold issue or if it is just depression...Anyway, I was very discouraged to find out that other people in other states had washing machines replaced, but why didnt I? I would be happy if they could buy back my old Maytag that I had prior to this Neptune, I am sure it is making someone very happy somewhere. Why couldnt they have respected my very true complaint? I was not trying to get something for nothing. I paid for something to keep us cleaner and free from allergens and instead wash my clothes in mold and have mold spores leaching into the air in my home. Please help.

Dryer doesn’t wash all the clothes and the dryer doesn’t dry anything correctly. All, regardless of materials or size of load, comes out damp. Repairman’s excuse was that it’s a learning curve(?) and our dryer vent was the cause (which it wasn’t as we had it checked out and there was nothing in it) and that was it. Very disappointed in the washer and dryer and now the company where we bought them as it seems that we’re stuck with over $2K worth of equipment that doesn’t wash or dry well. We’re awaiting to speak with manager for a replacement of anything not Maytag. Not holding our breath and definitely not a happy customer.

Bought a French door Maytag with freezer on the bottom. Ice build up on the bottom of the freezer and it has ruined my floor. We are replacing the floor in the kitchen. It is only a few years old. They have horrible customer service and will not replace anything.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

Purchased a Maytag Centennial top load washer that will not fill with enough water to wash clothes. The washer was purchased from Lowes on August 17, 2016 and we tried to return but Lowes refused because we were passed the required 30 day return period. We contacted the Maytag company and they sent out service people who reported that there was nothing we could do other than wash small loads. The company also reported that if we tried any of the solutions on the web we would violate our Warranty. Since we find ourselves in this spot (we should have read all the bad reviews here before the purchase) we have decided to place the machine in a very visible spot across from a new 100 store shopping center on a truck with a 4x8 sign warning the public not to purchase this product.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

Purchased a maytag washer last yr. and I feel it is the worst washer I have ever dealt with. I hate that every time I wash somethings they come out with lint all over them and they are the same things I have washed before and never had the problem, plus I hate the cover locks so you cant put water in before you put soap in.

The serial number is MDB8979SBWD. Just a few months before warranty expired the buttons were being flaky. Eventually it would not start. We brought it to the dealer because they wanted $150 to come to the house. They replaced the front panel. It lasted less than a year and stopped working again. Being out of warranty and being a technician I took off the panel and saw that there was no insulation in so the humidity would build up. The wires in the ribbon wire were corroded. I looked up the price of the panel and it was $150. The dealer wanted $150. I did not want to replace it because of the possibility that was not the only problem. We paid $400 for it on sale, (a mistake I know better than to buy stuff on close outs.) FYI to get the dealer to deal with it it would cost $300! From reading these complaints this panel seems to be a real problem with this and Maytag is not supporting this LEMON. I see a lawsuit here. Too bad Maytag is only out for profit. What is disappointing is that Maytag is owned by Whirlpool. Whirlpool has or used to have good appliances. We had a microwave that lasted 15 years and our last dishwasher that lasted 15 years. We will never buy Maytag or Whirlpool again. Maytag is junk. The dishwasher is probably ok except for the panel. Shame to get rid of it for that but unless I can bypass it that is what we will have to do. $150 is too much for a gamble and it seems that panel is a problem so it probably would not last long anyway.

Purchased the Maytag Bravos washer approx. 2.5 years ago. I cannot even begin to describe how disgusted I am with this washer. My clothes i.e. towels come out ripped on the edges, clothes do not get clean, shirts etc come out wrinkled no matter what setting used. It is not energy efficient because loads of laundry need to be washed twice if they are soiled (like our everyday jeans). Went back to the independent store where I purchased washer and was told to use only the bulky or gentle/delicates cycles to reduce rips in clothing. Such a complete waste of money, and it was not cheap!

I am extremely dissatisfied with the Maytag Gas stove and oven. The setting are too high and you cannot simmer something, it burns. I tried the oven cleaner and my oven is still dirty. The burner knobs do not have a click feature. I came home to a house filled with gas. I was not using the top burners, so I must have brushed up against the burner knob while using the oven. I was only gone an hour, imagine if I had been gone longer and walked in the door and created a spark on the rug.

Centennial commercial tech. washer - We purchased this piece of junk in Sept 2013, and had to have a repairman twice before it was six weeks in my home. I wrote several letters but the only thing that I received were applications for insurance to cover repairs. I should have received a replacement as it was bad from day one, but Maytag doesnt replace!!! Its been semi-reliable for the past several months, until early this year. It started jerking when it changed cycles, sounding as if the drum was hitting really hard against the sides. It has continued to do that regularly; now it wont function on the cycle its set on. It wont spin, sometimes the lid lock wont work. It starts filling when it should be draining. This evening, it stayed in the rinse cycle for 40 minutes and when I realized it was still rinsing I had to unplug it to get it stopped. It goes on and on, (and so could I out of frustration). The good name of Maytag has turned to trash, and when it leaves my home, no more Maytags!!! PS. The dryer we got with it takes at least 1 1/2 full cycles to dry a load, and since I couldnt get it to spin properly, Ill be lucky to get this last load dry in 2 to 2 1/2 cycles.

Maytag has really gone downhill. Had trouble with a factory defect in a new French door Maytag refrigerator within a few months (had it returned) and now the Maytag Centennial EcoConserve Top Load Washer no longer spins after only just barely 2 years of use... I will NEVER buy Maytag again. That is a promise. I will put more money and buy more expensive products from your rivals if it means avoiding Maytag products. That is my advice to anyone reading this review. The washer was used for MAYBE 10 loads of laundry per month... Yes, just for two people who have desk jobs so It was never stressed out. Used HE laundry detergent. Quality is a thing of the past for this company. Your reputation is in the doghouse.

This is my second washer in less than 5 years, going third. No customer satisfaction. Maytag/Whirlpool dont care, Customer Service doesnt care - all I hear when I call is, “too bad”, “so sad”, “call a repairman”, so you can spend another $100.00 plus. I hope this doesnt happen with someone elses brand when we buy it. Shame on such a big company.

This Maytag dishwasher has been really dependable, looks really nice, is really quiet, we have absolutely no complaints. I hope it lasts as long as I suspect it will. Would highly recommend this dishwasher.

This a 28-month-old bottom freezer fridge purchased from Home Depot. At about 26 months, the freezer started to leak water as ice was completely covering the bottom of the freezer floor and the excess water would then run out once the door was opened. I managed to get the ice out with slim bladed putty knife and did this about every 10 days. Contact with Maytag affirmed that I had no warranty available as it only comes with a 1-year, except for the compressor. Every effort was made to sell me an extended 1-year warranty for $330, and then a technician would be sent to fix the problem. I asked if the compressor had failed, would I be discounted as it is warranted and the answer was no, the fee was still $330. I had great difficulty in explaining why I would purchase a warranty for an item that is already warranted to no avail.I decided to go with their 2nd option of having a local appliance tech to solve the problem at my expense which I did for a final cost of $130. Technician came and immediately knew the problem and removed a little black rubber stopper valve that is supposed to let water pass but gets clogged and the water backs up into the freezer. It took him all of a half hour to fix everything, $85 for the visit and $45 for time in place, $0 for parts. He stated that this is a continuing problem that he has seen many times. Moral: Dont buy any Maytag products as the Maytag repairman who had nothing to do has died.

Purchased a Maytag Electric Range on Jan/9/2016 and delivered Jan 12/2016. To start the Aqua Steam clean is for the birds. Does not clean worth a darn. Model MER8600DH cost $823.33 and I thought this unit was awesome until December 2018. The oven makes loud bangs and it’s not metal contracting or whatever. I stopped using my oven. Tonight my top burner started snapping like an arc or short. Yup that’s it for me. I was thinking of buying a Maytag Gas Range as I was brought up on gas and I have a plumber coming this weekend to plumb for Natural Gas but after reading all the negativity on the gas ranges as well I absolutely will not be buying a Maytag now or ever! I expected more from Maytag. :(

Its unfortunate that Maytag expects their products to be so short lived, they wont produce parts for their appliances after 7 years. They just told me they are only required by law to make parts for their products for 7 years so thats what they do. So unfortunately, if your microwave outlives its handle, youre going to have to replace the entire appliance which will cost me almost $500. I will never buy another Maytag or Whirlpool products because of this.

Save money. I have always had Maytag & loved them until I bought the Bravos xl top load washer. The salesperson insisted it was a large capacity energy efficient w/ great maintenance record -- greatly misleading. The water level does not rise enough to effectively clean or rinse so clothes do not get cleaned or detergent doesnt rinse out thus allowing only 2 to 3 towels or jeans to wash per load. Such ineffective cleaning cycles create the ongoing need for loads to be rewashed and be extremely small, yielding credence to other consumers’ accusations of being mislead and false advertising of xl capacity. As such, it takes hours to wash a family of threes clothes. The machine shakes like crazy and clothes get ruined as they get twisted and tangled into each other ripping, tearing, misshaping and ruining them.

Maytag Neptune MAH8700AWW and MDE9700AYH Washer and Dryer - Electrical overload to house circuit, multiple water pump replacements (Maytag would not sell rebuild kit with impeller and gasket or seal causing us to have to buy complete water pumps with mounts and motor.), electronic error readouts, odor and mold washing machine. The welds breaking on the drum causing possible fire hazard by filling case up with dryer lint fibers, around the electrical components, and air intake heater and also allowing metal fragments to get imbedded in the familys clothes. Also, Maytag Oversize Capacity Plus Quiet Pack Heavy Duty with Lifetime Tub.

I purchased the washer 12 months ago. I liked large tub size and Maytag name. Thought I had made a good purchase. Boy am I am sorry. The washer overflows my large utility sink for drainage on large load setting and clean setting, ruining the flooring in an adjoining room. You cant wash black clothes in it leave white residue spots all over clothing. You cant use pod soap. Doesnt dissolve totally. Just on your clothing so you must wash again. So now I am trying to figure out what I can do but afraid I am going to replace it. Would Not recommend this product. Bravos XL MCT MVWB835DW1.

Fridge model mff2055drm00 - Purchased 2 years ago. Upon delivery and working water leaked from bottom. Called recommended service. Result took out fridge and brought in another new one. Today the fridge/freezer ices up, ends up sounding like a rocket ship. Not working efficiently. Called for authorized service. Was told needed a new thermostat... after TWO Years? Service call price $125, quote to purchase, replace and install thermostat $550. Almost $700. Big mistake buying Maytag- who knew? But never again! We are quite angry and very disappointed with the mediocre performance of this product.

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

Purchased our dishwasher 11 months ago from Lowes. Dishwasher has a 10 year warranty on racks and 2 other items. We are 2 adults in the household. Dishwasher is maybe used 4 times a week. Very light use! Circulation pump is bad which also took out the dishwasher solenoid. Im not going to fix because it if only lasts a year again that is a very expensive repair. Very disappointed in this made in the USA product. That was the reason I purchased it. Made in the USA. Come on Maytag. You can do better than this!

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Bravo Series Washer and Dryer. I hate, hate, hate this washer and dryer. I have had it for 2 years and hate it more every day. What makes is worse is the over $2,000 spent to buy this piece of crap technology. The engineer should be fired and sham on Maytag for selling such a piece of crap. Washer does not get clothes clean and I have pictures to prove the amount of dirt and lint and soap left on clothes and bedding. Very poor design, and worse yet absolutely horrible engineering.To wash one item on delicate takes 47 minutes. No way around it and you are limited to the water temperature you want to use and the spin cycle that you want for that item. Water level is too low no matter what setting you use. I have read and reread and gone step by step according to instructions with no success of clothes coming out clean. Clothes are also twisted and knotted and wrinkled like no other machine I have used in over 50 years. The washer is very limited in what it allows you to do. Bedding cycle is a joke that does not work at all. One of the reasons I bought this was so that I would no longer have to take the time to drive to a laundromat. I washed a comforter and so much soap and lint and dirt was left on the comforter. I still had to take it to the laundromat to get it clean.Dryer is just as bad. Even with the energy saver off it still takes 1 hour and 20 minutes to dry 4 towels that are 5 years old. I cant imagine how long it would take to dry brand new fluffy towels. It was engineered to sense when ONE piece of clothing is dry. I want ALL my clothes dry, not one piece and the machine shut off. How stupid is that??? Engineers - design it so it senses when clothes are still damp and the machine keeps running!!! I can only use the time dry setting because no other setting even comes close to getting the clothes dry.To top off the hatred of this machine some damn engineer apparently thought this was a car and needed to be aerodynamic with a curved lid on both washer and dryer so you cannot put anything on top of the machine!!! Not every house is 5,000 square feet with plenty of room and storage!!! They want to force you to buy the drawers to put underneath and then the washer becomes too tall for short people to reach down into to get the clothes out. There is not one positive thing I can say about the washer and on top of it I will never purchase another item from the store I bought this set from. I have had service come out time and time again and they say it is an installation problem. Installation says it is service and yet no one will admit it is just a very poorly designed machine. Do not buy this brand or series of washer and dryers. This series deserves a minus and the company should replace every set sold!!!

We bought a Maytag Bravos XL MCT Washer from Lowes in Oct of 2016. We had cycle issues with it in Sept of 2018 and called the Appliance Repair Service. IT was determined that the Electronic Control board and UIC was bad and needed to be replaced. Estimated cost - +$700.00. We bought Maytag because we thought it was dependable. Not so. Less than two years of use and repairs are more than we paid for machine ($639.00). Receipt would not upload.

My dishwasher like many others have mentioned is experiencing the same control panel issues. When I set it to Wash, it spontaneously goes to Rinse Only. I am unsure exactly the age, but given the number of complaints Ive read, with the same problem, it seems as though, there was a flaw many years ago in design and regardless of issues hasnt been resolved with the newer models either. I realize appliances dont last forever, but Maytag was always known for the lonely repairmen and Id hoped the brand would continue to live up to its advertising, despite being purchased by Whirlpool.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

Purchased a Maytag smooth-top range about a year and a half ago. Ive only cooked frozen pizzas in it. Have only had it on six or seven times. Havent used the top burners at all. Its an electric range, and I just had it hooked up a couple of months ago, as I was trying to find a place for it in the tiny kitchen. The folks who lived here before me, had a huge refrigerator and gas stove right next to each other, and I didnt want to go that route. Anyway, I went to put yet another frozen pizza in the oven, and the light doesnt work!So, after only six or seven uses, the oven light is busted! My mom had an old Westinghouse Terrace Top range, and it lasted well over 20 years with no problems. The only reason she sold it was because she remodeled her kitchen. It still worked great after all those years. Its after-hours now, but when I call Maytag tomorrow, Im expecting to get the run-around, if the other reviews are accurate, and Im SURE they are. Wont ever buy another Maytag product again.

Maytag Bravos 300 Electric Dryer - Purchased dryer 2011 and a computer part went out and Maytag wants $418.66 for a computer part. This dryer was used only 6 months a year. Poor attitude about repairing from Maytag and they would not do anything to make us happy with product. A dryer that goes out in 3 years is robbery. Maytag should repair and make customers happy but they just dont care. Anyone who buys a Maytag or Whirlpool product should have their heads examined. I tried to talk sense to Maytag representative but to no avail. I am now going to make sure all of southern Indiana knows of my problem with this product. Those who know me know I have the ability to contact thousands of southern Indiana and Louisville residents.

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

We purchased the Maytag over the range microwave December 2014. Three months after installing it the door cracked. Maytag did replace the door and the repairman thought it might be due to the heat from the stove (huh, it was designed to go over the stove, where there will be heat). Now, six months after that, the layers of plastic on the door are separating and the piece around the control panel is cracked. Maytag agreed to replace the control panel but refuse to replace the door as it is only cosmetic (their words). So much for paying a little extra for what we thought would be a quality product. It seems to me that if something was made to go over the stove, it should be made to withstand the heat.

Maytag 2000 front loading washer - This unit was purchased in Feb 2013 along with the matching dryer. From the onset it has presented with the problem of trapping small objects such as socks, underwear and other small loose objects in the rubber seal at the front of the door leaving them soaking wet and needed to be wrung out by hand. There is not any way to run a second spin only to wring out the clothes without doing an entire wash or rinse again rendering the efficiency void. I have been able to buy a mesh bag to put smaller items in for washing with the regular laundry load. However, this is not why I purchased the washer and I would strongly recommend to others not to buy this product. Very disappointed. I thought the Maytag brand was reliable. Never again will I buy any of their products.

I purchased the Maytag MFI2670XEM0 3 Door Refrigerator in Oct 2012. Thank God I purchased the extended warranty. The freezer has had issues with improper sealing since I bought it. It builds up ice around the bottom of the freezer where the seal meets. So bad it prevents it from closing. It happens fast, so I have to scrape it off every week minimum, to keep it closed. They have replaced the seals twice, all of the slide rails, twice and it still doesnt close right. I thought when I moved to Florida, I wouldnt have to scrape ice.Next: Ice maker quit working and had to replace that. Now, I came out this morning and about busted my ** when I slipped on all the water flooding my kitchen. The ice maker has a stupid little fitting on top of the refrigerator that has a rubber bulb connected to the ice maker water line. It split in half and every time the ice maker cycles, it pours water out that fitting and down the side. Why in the ** did they design it like that? It has caused damage to my cabinets and tile floor from running under it.Im sick of this appliance. I thought Maytag was known for quality. What happened to that? What a disappointing piece of junk and Im stuck with it unless I want to put out money for something different. There should be a Lemon Law rule for appliances like this. I have asked and get nothing from the warranty service but silence (crickets). They are sending out a tech again but that will require two service calls because they always have to order parts, which takes 2-3 weeks. Ive had to call them at least 5 times, which has amounted to no less than 10 service calls and here we go again. Stay clear of these units at all cost.

I bought my washer in 2016 and now it’s broke again. This is the fourth time! I’ve gone everything to take care of this and it’s a lemon! I will never buy Maytag again. I want to buy USA products but four times for repairs in three years is way too many. I guess it doesn’t matter what name is on it. My last washer was a GE and was still running after 15 yrs when I bought this one. Not one repair ever made on it! I’m telling everyone to stay away from maytag.

Model # MF12269VEQ1 French doors with bottom freezer - This refrigerator was purchased March 2011 and it is forming a sheet of ice on the bottom of the freezer. We tried unplugging it overnight to see if it would correct itself and it hadnt. I googled this complaint and called the manufacturer to see if there was a recall. It seems a lot of people are having this problem. Several comments are to pour hot water in the drain plug or use a blow dryer to to the plug; however, you have to disassemble the whole bottom freezer, then unscrew the back to get to the drain plug. I feel this is a defect in this refrigerator.This unit was approx. $1600.00 and should not be having this type of problem. Who knows if I could actually get to it to try these things, that it could keep recurring. Im very upset as my husband and I are seniors on a fixed budget. We bought the name Maytag because we thought they built good products.

I have always bought Maytag products, but I will never buy another one again. This washer is the worse. It never has gotten the clothes clean and it is so loud. It has gotten worse. I called someone out to look at it and now am being told that the bearing is going out. We havent had the washer for two years. The cost to repair is going to cost us $574.00. That is crazy. We are going to let it go out and buy another washer, but NOT a Maytag. I will do my research before buying a new washer.

I bought a Maytag dishwasher (model #MDBH979AWS3) from Home Depot on July 2010 and had it installed. After 2 weeks, I found water leaking into the basement. The installer said rubber gasket in water line de-laminated and caused leak under the dishwasher and flooded the floor to basement. Product defect and water damage covered by Maytag insurance. Now Feb 2012, about 1 1/2 years after buying, the touch panel controls dont work. I called Maytag regarding any control panel recall and they said no and its out of warranty. The advice given was that they can send out a serviceman for $269 to fix with parts, labor and one year warranty. It seems like planned obsolescence. Dont buy a Maytag.

We have had this washing machine almost 1 year and the small problems have grown enormous. In addition to the constant soap residue left on the dark clothes (my guess is its on the light clothes too, but you just cant see it) the washer goes out of balance frequently (they are replacing the suspension, after they said its all working great). The repair man said Im not loading the clothes properly, I need to roll each item of clothing into a ball and then place it in the washer. Are you kidding me, my new machine has special needs? And dont put in too large of loads. What!!! Its an XL capacity but I cant do an extra large load, because half the clothes wont get wet or clean. Maytag blew it big time with these models, I could talk about the dryer too. Maybe next time.

Called Maytag. Was part of 2005 recall with Neptune Maytag washer. We did not realize it and now Maytag will not do anything. Now having dryer issues with a cracked drum. Called and there was no resolution or attempt to resolve.

I purchased the Bravos XL washer and dryer combo 2 years ago. Dryer is fine, but washer was EXTREMELY noisy from day 1 and has gone downhill since. It would leak during spin cycle and frequently stop due to unbalanced load, refill and stop again. Now it wont spin at all! We have checked to make sure it is level, it is. I live in a very rural area and its very difficult to get repairmen to come out. This is my first and last Maytag for me.

Maytag Bravos XL: I purchased mine Nov. 9 2017. I so wish I had never bought this machine! It leaves soap residue and dog hair on my clothes and bedding. I have to wash everything 2-4 times. It’s beyond disappointing. My husband and I agree our clothes looked better dirty, BEFORE we “washed” them in this machine.

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

We bought a new Whirlpool dishwasher, and it was a nightmare. So after four years of that we tried their sister company Maytags dishwasher. I have to say that I think these two old American brands have been ruined. This Maytag dishwasher is always making my dishes smell like rotten fish or a dead animal. I have to dump bleach and or vinegar down in the bottom constantly to keep the stink down. And I have looked and there is no food laying in the grinder. Then we started to lose wash cycles, and the buttons (not real buttons but a cheapo control panel) started to malfunction after 2 years. Now, 3 years into it the plastic adjusters in the top rack are broken, control panel has gone totally haywire, and still smells terrible. I remember when American appliances were sturdy and reliable because they were designed by engineers. Now they must be designed by accountants and shareholders. Goodbye Maytag and Whirlpool.

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

I am also frustrated with Maytag for the same exact problem... The control panel and the dishwasher not working just after our year warranty went out. I purchased this product because we had a good experience with a Maytag Dishwasher lasting about 20 years, only to get fooled that the quality is not there any longer. This seems like BAD business on Maytag, Whirlpool, and Home Depot! How can we get an official complaint to someone who can fix this? Another example of big businesses that do not care to take care of customers! Why would a company like Home Depot continue to support this business!!

I purchased two Maytag appliances; PC-touch control 500 Electric Smoothtop and a dishwasher. In less than two years, I have spent over $1,000.00 repairing these two appliances. With my stove, I have replaced the PC control board and the oven light kit. Less than a year and a half, I now need to replace the PC control board again. I have been a Maytag customer since 1976. The dishwasher had a recall for the heat element and I replaced the control panel control board and door lock switch and the main control board. I will never buy Maytag again.

Purchased a Maytag Dishwasher (Model MDB7749SBBO), total with tax $590.34 on 3/31/13. It wasnt a cheaper model, had stainless interior. Owning it after a 1-1/2 year, the Control Panel went bad. Maytag offered me for $267 for repairs and 1 yr warranty. Why thats about half the price I paid. My personal repairman told me the cost would be around $200 to replace the control panel. Why I could get a more inexpensive model for $300 and still get a year warranty. Very disappointed in Maytag quality of their product.

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

We have had this washer/dryer stack up for about 2 years now. Not long after it was purchased from Best Buy, it started smelling like mold, even though we were doing everything possible to keep it ventilated. Best Buy employee said that service was not covered by the warranty that we purchased, so they suggested we YOUTUBE some ideas on how to get rid of the smell. They said it was a common complaint for front load washers. We have tried Affresh, hot water and bleach, hot water with vinegar and lavender, etc. Nothing is working. There is mold on the plastic inside the washer door and the stench is horrible now. You can smell it when you walk into our home. I believe that stench is the reason we are all having respiratory problems, allergies, etc. I just dont know what to do anymore. Really frustrating!! These appliances cost a lot of money.

Maytag Bravos MVWB725BW - Purchased this washer last year and have been very unhappy with the way it washes. It is extremely harsh in the way the agitator moves the clothes. Because it has a low water level the clothes take quite a beating in the washing process. This is confirmed when I remove the clothes from the dryer and proceed to clean the lint filter. The filter is constantly full of lint, even after drying clothes that have been washed numerous times before. Additionally, the clothes, even though being put in evenly, end up bunching together.

We bought the Maytag Bravos washer & dryer combo from box store. I wanted an extra large capacity washer to accommodate king sized bedding, and having fewer wash loads in general. Cons: 1 - This machine is not energy efficient when each wash load takes 1:30 to 1:50 each load. 2 - The detergent/fabric softener/oxi dispensers are a joke. Water dumps into every compartment at once. And if there’s still detergent left by the rinse cycle, well you get the picture.3 - The “Bedding” setting is the only one which will provide enough water in the tub to get anything wet. Since there isn’t any type of agitator the clothing/bedding just floats on the surface in dirty perfumed water. 4 - With any of the other settings the water level is so low it doesn’t always get everything wet so items are not being washed properly. At most maybe 2 pairs of jeans or just a few t-shirts can be washed on the “Normal” or “Power Wash” settings. 5 - Because there isn’t an agitator, clothing gets knotted up. Dress shirts, dress pants, jeans, towels, you name it, everything comes out of the washer in a knotted mess.The Bravos XL Dryer: My only complaint with the dryer is that it allows a good amount of lint to pass through into the machine. Then it’s difficult to get any type of lint brush into the vent area to remove the lint. Dampened lint in the machine can make clothing smell musty and nasty. I had to call a service to remove lint from the dryer & ducting because of the odor lingering from the inside the dryer.

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

I bought a Maytag Bravos top loader in Oct 2011. About a yr after having it, it started having problems. At the end of the cycle, theres still water in the tub and clothes are soaked. A couple of months after that, it started completely skipping the wash cycle, so the clothes would just sit in dirty water and do nothing. I called the small appliance co. I bought it from and by the time I get done paying a house call and parts, I might as well buy another one. I called Maytag because it seems theyre all having the same problem and at some point youd think they would be responsible for their product. They couldnt care less and the options they offered me were a joke!! Please, whatever you do, DO NOT BUY A MAYTAG because you will be on your own if anything goes wrong (unless you want to pay them the price of a new washer!!).

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

I purchased a dishwasher and stove from Home Depot. Stove has already been replaced twice because of faulty manufacturing and now the dishwasher, after 1 1/2 years no longer works due to the control panel. I called a repair representative of Whirlpool/Maytag and explained the circumstances. Their own customer service people indicate that it is cheaper to replace a product then it is to repair it. Shame on Maytag and Whirlpool that they move their companies to countries outside of the United States and they no longer stand behind their product. Shame on them that what use to be the best product around is no longer worth paper you print on. I will no longer purchase any product from Maytag, Whirlpool or Home Depot since they all seem to line their pockets from products they know wont last. One mouth is worth a thousand complaints and I plan on screaming from the rooftops!

I wished I researched more before I purchased, but like most people, I believed in the reputation of Maytag. Like many others - my control panel started to go out 19 months after install: Had my first event with the washer; it would not allow me to select normal wash. A high-end machine shouldnt have electrical connection problems within 19 months, just 7 months after the warranty expires.When the repairman pulled apart our machine, he found a similarly burned looking touchpad ribbon cable, that was burned in exactly the same position as the photos shown on Maytags website under the review referred to. Maytag/Whirlpool has set up a special phone number to deal with this problem: I dialed 1-866-931-7384... Been on hold for over an hour Of course - NO answer! Ill try later but I am very angry that this has been a known issue BEFORE I purchased mine at Home Depot. What a piece of junk. This is the last Maytag Ill ever buy again. The service is horrible, the product is junk.

MFF2558VEM0 - Had the same problem repaired less than years ago.. Now has the same problem. Looking for a new fridge. Hope better luck this time.

What junk. Bought this gx2shbxvy05 french door fridge. In less than 16 months the freezer is fine the fridge section gets up to 80f. Throw all the food away. Found the freezer coil covered in ice. Took the back panel off and noticed ice around the copper tubes by the compressor going up into the body. Not good. Put a small brick heater in and slowly melted the ice into the drip tray. Warning, it filled up 4 cups of water and of course spilled and killed the wood floor. After the clean up. Plugged the unit in and it seemed to work for about 3 months. Now its dead again. Looked into parts around 300 to 400 bucks plus labor to replace the system needed parts. P.S. the fridge, this junk replaced is downstairs working after 25 years not one issue other than the color. NEVER BUY A MAYTAG product please. TRAIL APPLIANCE should never have sold this product and should have stepped up to help out. Wont buy from them again.

Maytag bottom freezer, 4 years old, ice forms on bottom of freezer. Water melts all over floor every few days. Please add my name to class action suit if/when one comes.

Due to our previous washer breaking down, we had to purchase a new washer. We have always been loyal to Maytag since we were always pleased and satisfied with the performance. However, this new washer does not deliver in performance, cleanliness, energy savings when cycles take much longer and you end up maybe not using as much water, but our electric bill has gone up considerably. I have nothing good to report about this washer. We purchased it back in April of 2013, and Ive given it the benefit of the doubt by experimenting with all the different wash cycles. I am just not happy with it. I so want to trade it in for a front loader and give Maytag one more chance.

I purchased this washing machine from Home Depot in 2012. I am amazed that it lasted this long after reading the reviews on here. It will not drain water, it will not spin. I see many customers bought the same washer and are having multiple issues. When will Maytag recall these machines? Overpriced and unfair to consumers to sell something that is broken or not reliable.

Hello, I purchased a Maytag Bravos washer model MVWX655DW from the Home Depot in June of 2017. I can provide the receipt. Within 6 months I had a broken lid switch and the unit would not move through the cycles. Luckily, I had the ability to replace the lid switch at the cost of about $100 just for the part. The repair was fairly involved. This summer, the unit failed to agitate, upon much research, I learned the washer drive hub (which makes the washer agitate and spin) was worn out. It was made of plastic and it is quite a job to get the cover plate off and to replace this part which ranges in price from $20-$45. This is a fairly difficult job and I would not recommend it to most people. It should not be needed in a 3 year old machine. Upon inspection of the drive shaft teeth when I took the washer apart, I found the steel teeth to have significant wear. Why? Now, in mid-November, same issue, the plastic drive hub is worn out again! I was told maybe my shock absorbers for the drum needed to be replaced as the drum may be shaking too much. My previous washer was good for 18 years and I replaced it with this highly recommended model Maytag with the chrome basket. This is absolutely the worst appliance I have had and with every repair, I viewed many, many people with the same complaints and feeling that Maytag should issue a recall on these machines. I will be contacting Maytag and Home depot with my review. The HD installer also stripped the plastic valve one of the water hoses goes on that I had also to replace. A $40 dollar part. This took some disassembly but not as bad as replacing the drive hub every three months. Needless to say, I have to buy a new machine after 3 years of unreliability with his machine. A waste of $500 + of my hard earned money. Very, very disappointed. If I wasnt mechanical and able to fix this washer, it would have cost me hundreds in repair bills. I have receipts of the parts I have purchased for this unit. I hope your experience is better if you have owned one of these machines. Maybe I just got a bad one but many people have complained about this model so I dont believe I am alone. I hate to see good people spend their money on poorly constructed machines. I certainly expected more than 3 years out of a brand new appliance. Maytag and Home Depot have lost a good, long time customer unless they want to make it right. Please feel free to contact me.

Worst brand ever. They both broke at the same time. Spend too much money. Never buying these brand again. Maytag sucks. Dont buy Maytag washers or dryers.

Bought this as W/D set brand new from Home Depot. Had been noticing incredible wear and tear on clothes, as things get so tangled up and need to be practically ripped apart before going into dryer. Cycle times are crazy long, up to over an hour in some cases. Doesn’t have a “Speed Wash” cycle. But WORST of all, after less than 3 years, it just stopped draining properly. Tried all the Codes test, etc. Finally called a repairman just to be told repair costs would probably cost more than the machine is worth. $125 to be told we ought to just buy a new washer. Not happy.

I just purchased a Maytag Washer and Dryer. I am very pleased with the cleaning ability of this washer. It has set pre-timed washing and drying times. I would like to have availability of setting the times for a load to run. Same with the dryer. The book says you can do this but I have not figured out how. I have been very pleased with their abilities to do what they are supposed to do. Cleaning and Drying.

We bought our new Maytag top loading washer and matching dryer about 2 years ago. I am a busy woman so I havent had the time to write a review, but today being my day off, once again I find myself frustrated and disappointed with this set. The washing machine has a huge capacity, which was a huge selling point for me, however, if I put more than a small load in, the clothes come out still dirty, stinky and even have dry spots on them where they werent even in contact with the water. Even on deep fill it cleans the clothes inadequately, but at least they get wet. The dryer leaves the clothing rough and wrinkled unless I use the delicate setting, which I do for all cloths, and I use fabric softener liquid and a dryer sheet.I had a front load washer and dryer before, and my clothes came out clean and beautifully soft, but I replaced them because of the musty smell problem from the washer. I wish I would have kept them and figured it out. This set is the worst and I spent so much money on them. It takes so long to wash a load of laundry, and there is no way to interrupt a cycle without it draining and starting over completely. I have tons of laundry to do and I started 2 hours ago and the first load is still going. Geesh!!! Dont buy a Maytag. I paid for the extended warranty, but they are not broken. They have sucked from the very beginning.

According to repairman this washer had a very common problem with what mine was doing. Water was gushing up out of the detergent, bleach, and softener dispensers and running out onto my floor. It was going to cost an arm and a leg to repair it. Mind you this washer isnt even 3 yrs old yet. Called the manufacturer and they basically told us that we should have purchased the extended warranty. We said if so many washers of that model had that problem they should have had a recall and fixed it for the customer. They said it wasnt a safety issue. I asked if falling on a floor covered with washer water and breaking a hip isnt considered a safety issue? No more Maytags for me.

I had purchased a brand new Maytag refrigerator and in less than a year, the ice dispenser stopped working. I had called Maytag warranty department in regards to this matter and they flat out said, There is nothing we can do about it. I will never deal with this company whatsoever and wouldnt recommend it to anyone about it. Less than a year and they refuse to fix the item they sold. No better than a used car lot attitude.

We purchased a French door Maytag refrigerator model MFD2561HEB in November 2007. In August 2008, the unit stopped working suddenly. The high voltage control board was replaced under warranty, but the tech could not determine why the board failed. I called Maytag to demand a new refrigerator. The best they would do was to extend the warranty for 6 months, no charge. The unit quit twice more in September. A tech was summoned (paid service call), nothing found. It started working again. Since then, the thing has quit several times. We unplug, move all food to a second refrigerator, wait a day, plug it in, and move the food back. The useless box quit completely this week, not quite 5 years of service life. The tech said the board must be replaced again, no guarantee. We declined. I called Maytag again to demand a new replacement and escalated the complaint. They are to call back, ha! In the 5 years of poor service (and poor customer service) from Maytag, the 30-year old second refrigerator has been up to the task of preserving our food. This experience has made me vow never to do business with a Whirlpool-affiliated brand again.

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

We had a Fisher & Paykel Washer that lasted 14 years. This Maytag Bravos XL washer has been the worst machine I have ever owned. The clothes come out dirtier than ever. In todays world all technology is becoming disposable, Where is the Maytag repairman now? I have tried all of the settings, to have a decent wash. I am ready to throw this out. Lowes you need to do something about this. It may be made in America but now we know why Japanese and Korean electronics just work! Damaged Clothes/Clothes not being washed thoroughly enough are my biggest pet peeves with this washing machine.

I purchased this machine (Maytag washing machine model MVWB700VQ0) from Home Depot in December of 2008. When purchasing it I decided to spend a bit more money on the machine, thinking I would get a quality product. For the last two years and 5 months it has only been me and my wife in the house as the kids are in college. Hence, the washer has not been used as much as some would use it. Within the last two and one half weeks the machine started making a horrible growling noise (probably the tub bearing going bad) and then started to leak yesterday. I noticed this morning that there was a large puddle of bleach water coming from under the machine. I called Maytag, which is just a fancy name for Whirlpool, and they basically told me too bad. It is inconceivable that a machine that used to last 20-plus years barely lasted three with only two adults using it. When I owned my previous home in another town the house came with Whirlpool appliances which literally fell apart within 5 years. I wanted to stay away from Whirlpool; however, I did not know that Maytag was owned by Whirlpool. I have received no assistance from Maytag. I am absolutely disgusted with the fact that an American iconic company such as Maytag is producing such garbage. I am going to be forced to figure out and fix what is wrong with the machine myself. However, I do believe this subject should be looked into further and possibly a class action law suit against Maytag for bad customer service since there seems to be quite a few people with issues surrounding this machine.

I purchased a Maytag Centennial washer a few years ago. In my opinion it hasnt worked properly from the start. We went on the low end of price, because we spent a small fortune for GE products that broke after a year and a half. This Maytag hasnt been a much better experience. First it didnt drain and spin clothes, and I was told I was using too much soap. Cut back on the soap and it started working better and going through the full cycle but the clothes never felt or smelled fresh and clean. Now 2 1/2 years in, it doesnt complete the full cycle on its own, AND there is dirt in my washer after every load. My clothes come out with streaks of dirt on them. The picture below is of a pillow case I just took out of the wash! Ive cleaned the washer multiple times, but it doesnt drain properly so it doesnt help. Maytag charges a service fee just to come out and troubleshoot and charges you again to come and do the repair. Im running out of reputable companies these days with washers.

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

Well Maytag, I have to say that I am very disappointed with your washer. When I put it on the bedding setting and try to wash a big load, it barely moves the load around. If you have a regular agitator to replace this useless one that is in this new washer I would like to have one. My laundry is barely getting washed and when you look inside the washer everything that is on the top stays on the top, not like the older washers where you could see that the laundry was getting sucked down with the proper agitator.

A little over two years and my Maytag dishwasher needs 300 to $450 in repair for circuit board or boards. The repairman said that they got cheap and left out a seal which allows moisture to get into the electronics, duh. They have a known problem but will not stand behind their screw-ups. Never again will I purchase Maytag, Whirlpool or any other product made by the bumbs.

I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

I am very pleased with the product, a perfect stove for cooking! It’s very easy to operate, easy to clean, multiple burners, excellent in cooking large meals, like soup, beef, Chicken and vegetable soup. It’s also very energy efficient, very safe to operate,

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

I was all too excited to FINALLY own a new set! I conducted research and read reviews. We decided on the Maytag Bravo XL set (Lowes) and was thrilled! For the first 6 months. They were both fantastic! 6 months later, several times the clothes washed were soaking wet as if they had been set on soak. It continuously alerted to clean after 3 loads. The dryer... Well, evidently, if you live in a high-humidity region, DO NOT HOOK TO THE WATER LINE FOR THE STEAM OPTION. It will soak your dry clothes! After 3 loads of drying, it fails to re-start for the 4th load for at least 12 hours! When paying over $1,590 for a new set, this should not be an issue. Mind you, I do laundry once a week - 5 to 7 loads including linen. Fortunately, we paid an additional $200 for the warranty at Lowes.Lets see what happens there!

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!