The engineers at Maytag saved a few pennies by only using one thermistor for temperature control. It is in the box. There is nothing monitoring the temperature in the freezer. If you put your fridge in the garage where the temp is 40 degrees, the motor will never come on, and your frozen foods will melt! In my new MRT118FFFZ01 unit, the temperature in the box varies by plus or minus 3 degrees F, but the freezer varies from minus1 1 to plus 25 degrees F. 36 degrees difference! Lousy design. Have had two service calls, and they both said that this was the way it was designed and there is no fix for it.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

In December of 2013, I purchased a Middle of the Line Maytag Dishwasher model #MDB8949SBW for $600 plus $200.00 for install and removal of 5 yr old Kenmore. At that time I thought I did my research and saw no major negative flaws on this type of machine or similar machines. This replaced a 5 yr old low line Kenmore that just upped and died. Installed just before the holidays, this Maytag machine seemed to have worked tirelessly until a few days ago August 18/2015. The computer controls went haywire. I was hitting normal start buttons and other buttons on the other side of the control panel were blinking and lighting up. Worse was trying to cancel and the control boards were not responding. Even hitting the start button, the machine would not turn on. Finally looking at the facia, I see the tabs of the flexible plastic frame that hold the control panel popping out from underneath the white facia plate. Snapping the frame back in and applying a lot of pressure got the machine to operate. With a family of four and minimal storage space, this machine is used approx once a day. It appears over the year and 1/2 by pulling on the plastic handle - which also happens to be the computer control board frame, the computer has separated from its mount and has allowed moisture to hit the control board/computer and wreak havoc on the electronics. Looking up this model online NOW, I see I am not the only one with Dishwasher computers failing within a year or two- just out of the one year warranty. A Call to Maytags customer service has the computer control board alone cost $160.00 plus the service tech and his labor fees reaching in excess of $450.00. The CS rep gave me a repair discount to $267.00 and a week wait for the Service Tech for this problem to be fixed. I bought this machine on two premises - one for its price, it was the only machine that offered 3 spin jets that really do a good job in cleaning dishes and 2, I owned a 1984 Maytag dishwasher in another home with computer controls in the handle and to this day, that machine is still running flawlessly! My only issue with the 84 Maytag machine was after 4 years the door gasket went - too much soap - replaced and no issues since! I expected similar performance with this one. I guess I have to spend north of 3 bills for similar performance and quality. What was I thinking?

I purchase my Maytag Bravos washer from Sears in May 2011. In February of 2014, I started to get the UL message, meaning unbalanced load. I would re distribute the clothes and sometimes that did the trick and others not so much. Now every load comes up UL. I tried putting the machine on the drain and spin cycle to at least get the clothes a little bit drier but the UL message still appears and the clothes are still soaking wet. I lifted the washer up and there is an oil/grease type spin pattern under the washing machine. I called Maytag today (which is now Whirlpool I guess) as the washer has a 10 year warranty on the drum and motor. I was told a service call is $129. When I mentioned that I had Googled the product and saw many reviews with the same exact problem, she stated the Bravos has no common complaints. From what Ive read, it seems to me it would be more cost effective to go out and buy a new washing machine and it obviously wont be another Maytag or Whirlpool.

To anyone out there who is considering purchasing a Maytag washer. My husband & I purchased a Maytag Bravo top loader washer from Sears Hardware here in Columbus, OH. We had always received great review regarding Maytag products. This washer is expensive & does not work. We started having problems from the day we purchased & had Sears come out three times for repairs. This washer has a built in scale which is extremely sensitive. We are very disappointed in this washer. It takes an entire day to do 3 loads of laundry. The washer goes off balance on every load. It doesnt do a god job cleaning the laundry. I do not suggest the Bravos series to anyone consider purchasing this product. It is a piece of JUNK! We purchased in Aug 2010 and the washer will need to be replaced within the next several months. Keep in mind that more expensive & lots of fancy extras doesnt mean a better quality washer or dryer. Stay away from Maytag or you will have the Old Maytag repair guy @ your door frequently.

My husband and I purchased a Maytag Neptune washer and dryer set back in early 2005. It was our very first major appliance purchase together as a young couple. We were talked into going with the Neptunes as it was considered one of the high end models at the time, and it came with a 10-year manufacturers warranty, which by itself was a major selling point for us. We have now had our Neptunes for a full decade and I am happy to report that we have not had one single problem with either the washer or dryer the entire time we have owned them. In fact, they are still going strong to this day. However, as it has been 10 years, it is now time for us to upgrade. We have purchased all new kitchen appliances within the past year and we decided that its now time to upgrade our washer and dryer as well and go with a steam set. We will most likely end up selling our Neptunes since we will have no use for them once we get our new set. They have served us extremely well over the last 10 years and we wouldnt hesitate to buy Maytag appliances in the future.

In October 2017, I purchased a Maytag MVWB765FW0, thinking that it would live up to the Maytag reputation but I will NEVER buy Maytag again. This machine is more suitable to wash industrial canvas rather than clothing and bedding. All the laundry is twisted and mangled and ends up in a large tangled ball at the bottom of the tub. My clothing is being destroyed faster than I can replace it.

My Bravos XL is worthless!!! This lack of agitator design is totally ineffective. Dark clothes come out with white powder on them and I use the liquid detergent. Whites I soak with detergent and bleach then full wash cycle. Still stains on dish towels and socks. Never had a problem with the old agitator Maytag. And yes the wrinkle free cycle creates wrinkles. Deep water wash is only cycle that even comes close to cleaning and its far from perfect. Horrible waste of money, buyers beware!!! I thought all those negative reviews were overblown and since I couldnt find a large enough machine with an agitator, I ignored warnings and bought this garbage. Matching dryer is fine.

I bought a Maytag washer and dryer, the Neptune series and thought I was getting a top of the line, but now the dryer has quit working and the repairman said it is not worth fixing and it is only about 5 years old. So that is what I am so angry about.

Bravos XL IS A JUNK. I have had this Maytag washer maybe 2 years at most and it is junk. I called. Told/complained them about the noise during wash cycle and spinning. The 10 years warranty is falsely. The 10 years warranty is covered only 2 components in the entire machine ???? and does not include the labor cost of $130.00 an hour. Sadly, I have seen many negative reviews their product. I didnt check reviews before purchasing, I knew I needed a large basin and wanted the deep fill option. I always thought maytag was a good brand. Now I am in a jam. ???? If you are looking for a new washer read the Maytag reviews before considering this brand. Live and learn. ????

This machine does a great job at cleaning clothes. The clothes are always great in color, and removal of removable spots. The cycles are not too long and the machine is not noisy. Machine is nice looking and water cycles can be normal or large.

I have had two Maytag washing machines in the past. Both lasted 20 years. Three years ago I purchased my first Maytag front loader washer and dryer. The washer is terrible. Although I clean it regularly plus spend money buying Affresh tablets and leave both the door and the soap dispenser open, the washer smells and builds up tons of mold. Cleaning out the heavy mold in the soap dispenser area is almost impossible. I spray bleach in there and then try to stick my arm into the back where most of the mold accumulates. Cant really get it all. Also, there is a problem with the softener dispenser. It gunks up and gets clogged. Had to keep pouring hot water and vinegar into it. Contacted customer service who was no help - they simply wrote to clean the machine. Huh? The dryer turns sheets into a tight roll with the inside not drying.

The washer I bought brand new has never worked well. The clothes end up all bunched and twisted up together. The bleach is not distributed properly, I have big blotches of white spots. It is leveled, still shakes and everything is on one side

Maytag 7000 series front loaders bought in 2013 on basis of high ratings from Consumer Reports. Also durable and look good in the process. Had for 3 years. Machines highly rated by Consumer Reports and bought on sale. They were a very good value. Both W & D have steam feature but find Ive rarely used it. Durability is key, as is the ability to balance wide variety of loads, which our machines do well. Capacity of 5 cu ft or better sufficient for a household of 2. Maytag reputation for durability and reliability and made in US, though a clone of Whirlpool. These are big, heavy machines, best for side by side but they can be stacked. The units are quiet, have more features than weve ever used and so far have been reliable, gentle on clothes incl delicates and drum bearings really help with keeping loads balanced. Door hinges built like a tank but the chassis theyre attached to arent up to par. W & D have stainless drums. Washer is resistant to mold & odors but dryer lint system convoluted in design and hard to clean out.

In the winter of 2007, we remodeled our kitchen and bought all new Maytag appliances. They cost a little more but we felt that we were getting a good quality product. Within months, the handle on the freezer became loose and I had to call for a repairman to tighten it. He told me we should buy the extended warranty because only a trained repairman could fix the handle. That turned out to be untrue thankfully because if it was true, I would have to call for repair at least once a month. The handle is constantly coming loose. A few months later, the microwave would turn on when the door was closed. I called repair as it was still under warranty. After he removed and replaced the door, I was told that we have to be careful when we close the microwave. There was nothing he could do to stop the problem. Approximately three years after we purchased the appliances, we had a problem with the dishwasher. We could only use one function; the others would not work. We were told by the technician that we got water into the door where the controls are and ruined the motherboard. I never heard anything so absurd. I have had a dishwasher in the same place for 25 years with no mishap. The cost of repair was $800. A few months later, we had a problem with the large burner on our cooktop. The outer coils heat up but the inner coils do not. I have yet to call for repair because I do not trust Maytag. Now, our microwave does not work. My husband used it to make popcorn with no problem. A little while later, I tried to heat a cup of coffee and it would not heat. The keypad works, the light comes on in the microwave but the motor does not run. Needless to say, we are very unhappy and will never buy another Maytag appliance. I wish I would have read the reviews before we purchased the appliances. Two of our friends had their kitchens remodeled at the same time we did and they have not had any problems with their appliances. But they didnt buy Maytag. I guess thats why.

Purchased Maytag Jetclean Dishwasher Model # MDB7749SBM3 on March 19, 2014 and on June 10, 2017 the washer would not go through the cycles properly. So I got on the internet to check out the problem. Maytag has very flimsy wiring circuit on the back of the control panel that rusts out due to being close to high-temperature water. Obviously a design flaw. The only way to fix it is to replace the control panel for $150 dollars with another flawed part. Do not buy Maytag dishwasher.

I purchased a Maytag dishwasher delivered in dec 2012. We are snowbird Canadians and the dishwasher is only used 5 months per year. Jan 2015 the control panel quit working and the repairman tells me the wires on the control panel have started to melt down. He called Maytag and was told they had extended the warranty on this machine for one more year. Missed it by 2 months. Considering this was only really used one year, I am very disappointed. How can an extended warranty on a safety issue only be for one year? This is my first Maytag product and will be my last. I only purchased it because I was told Whirlpool bought them out and I have never had a problem with Whirlpool.

I bought a Maytag Centennial HD washer and dryer. I have had no issues with the dryer but the washer is absolutely junk. I’ve had it 5 months and this is the second time it’s stopped spinning and I’m dipping my wet clothes out. Not only does it cost hundreds to fix it, it doesn’t wash well AT ALL. Your clothes still come out with deodorant stains and spots. It’s a complete waste of money and time. Run as fast and as far away from this worthless machine as possible.

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

I, too, have had major problems with this Maytag refrigerator! We have experienced everything from a malfunctioning ice maker, flashing control panel, overloaded compressor, erratic freezer (freezes much of the fridge contents), and doors not staying closed/inadvertently popping open. We have owned this fridge since 2007 and have repaired the ice maker and the freezing problems on our own dime. When the clicking sound woke the entire house up at 5 am, I finally decided to post! I realize that appliances are not perfect, and that Maytag had the best of intentions when designing and producing this product, but what really infuriates me is that Maytag has known about this widespread inherent problem since late 2006! Why no recall? Why no notice? Why no assistance? When I called the customer service line this morning, the representative acted like shed never even heard of this fridge having problems - yeah, right. All you have to do is Google the model number or just Maytag fridge panel flashing and clicking problem to discover thousands of similar complaints. I do not fault Maytag for manufacturing a less than perfect appliance, but I do hold them accountable for adequately repairing/replacing such a rampant and unsafe (compressor overload) product! Maybe it is time for a class action. Something needs to be done to protect the consumer from a company that is so slow to correct a long-standing and potentially dangerous problem!

Having had a household for over 40 years we have had a few washers come and go. I hate to say it but this line of washers should go. Worst pile of junk parts I have seen. Bought it from Costco a few years ago based on past histories of Maytags. Was I ever so wrong. It has never worked well. I chalked it up to being Water Efficient but after reading over 8 pages of scornful reviews, I was mistaken. Water level is always too low to do anything so clothes are needing rewashed. Have reverted to using the Bulky setting to do general washing as that fills the tub about 1/4 of the way. Then the spin cycles stops due to unbalanced load and loud banging of the wash drum, EVERY LOAD!!! And now for the past month Code DL pops up saying it is taking too long to drain. I have checked all hoses for blockages, none seen. And with the glass top, you can SEE the washer NOT WORKING right. We have a door on the laundry room and even with it closed the volume is over 70 dB and can overpower most conversations in our family room 20 feet away. I have been told that Costco may take it back but why punish Costco members for a design failure of Maytag??? Has anyone thought about a Class Action Lawsuit? The Bravos Quiet Series 400 dryer match to this washer has so far been flawless. I may have to dig the 20 year old Whirlpool washer out of the storage shed to replace this Maytag. Sad. I want to state my true feelings but I will not use profanity here.

I bought 4 appliances - stove, refrigerator, dishwasher and microwave. Just after 1 year, our dishwasher stopped working. Serviceman said it was the motherboard. I had to talk with a supervisor in customer service to get it covered and found that it was only a switch that was bad. Next, our ice maker overflowed with water, causing damage to our new hardwood floor. Again, I had to talk with a supervisor to get this covered and I did not file a claim for the floor. Then, our stove shut down. Repairman found that a wire was shoved into the top box, causing them to be exposed and shorting out the system. Now 2 years and 4 months, our microwave is not heating and I have to call for service. This was a brand-new kitchen that was remodeled and all appliances were new.I am very disgusted with Maytag products and their attitude of We are sorry, but there is nothing we can do as the warranty has expired. It used to be 3-year warranties for Maytag products until they were bought out. Never will I buy their products again. Have been married 40 years, and our other appliances for 38 years never failed and to find that these products are made in the USA.

It washes extremely well. Its reliable. The wifey loves it and thats enough for me!!! I have had no major mechanical issues. Since 2012 we use it heavily and every other day. I would purchase same brand if need be but Im confident that would probably be in 2024.

Worst washer ever. Wish I had read all these reviews before I bought. I have had the same poor experience. Laundry doesnt even get wet while being washed. Agitation does not affect laundry. Just moves back and forth under laundry. Clothes do not come out clean. Feel I was ripped off.

Im an 78 year old man, married in 1962. In all the years and two kids we have had just three Maytag washers. To me the gold standard of quality washers. When the motor went out in our 15 year old Washing machine I considered replacing the motor, which is well within my capability. I am a journeyman industrial machine repairman formerly with Ford Motor car company before retirement.Instead, my wife and I bought a Maytag top loader high efficiency washer from Best Buy. I was skeptical when I examined the new machine with paddles instead of the agitator. Trusting that Maytag had engineered a water saving washer using paddles, I made the very poor decision to buy it. I regret not replacing the motor in my old machine. Boy was I wrong. Given the chance I would trade my new machine for the old in a heartbeat...The old machine washed everything we could throw at it. The new machine wont wash anything to my satisfaction. The bedding deep fill cycle is the only one capable of a passable job. Even then I would like a soak cycle which, in my opinion, would vastly improve results. In all I would characterize this as a total engineering failure. Why Maytag would allow this POS to be sold, where the reputation of Maytag is totally destroyed, is beyond my comprehension.

Two in a row make it just over a year then the control panel goes out. You call a Maytag repairman and they say the control panel is bad! #1 it should last more than a year and a half. #2 a part shouldnt cost you as much as the darn dishwasher! Do not recommend nor would I ever buy another Maytag.

The AquaLift Self-Cleaning is a very poor substitute for a normal high temperature Oven-Range. It gives as much work as an oven without any self-cleaning, as it does nothing to the sidewalls or the door. The minimum temperature is 170 Fahrenheit, too high to rise a dough.

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

For families where people work in gardens, work on vehicles and get just plain dirty doing things anywhere outdoors these agitator-less machines are not for you or me. Ive had mine for two years and I truly dislike it (Model MVWC425BW1). With different products I scrub dirt and grease stains on pants before they are put into the washer, scrub again when they come out of the wash and then scrub and wash again a few more times but I cannot get all the dirt out. I now work more on laundry and harder since I got this machine.This agitator-less machine is designed for people who dont get really dirty - just remove everyday perspiration and household grime. I think this machine was designed by engineers who have never done daily laundry for any length of time and theoretically thought it would clean really dirty clothes. They were really wrong! Having done laundry for 50 years, I now know that an agitator cleans better. It would be nice if other women and I, who have done laundry for years, could be on focus groups about developing new washing machines.

I purchased this machine (Maytag Bravos XL MVWX700XL2 ) about 18 months ago. I was so excited with the looks and the reviews I found on the machine at that time. For the first 14 months I was happy. All of a sudden, it has become the washer from Hades! It twists and almost ruins my clothing. Not to mention, I think it is permanent wrinkles that it puts into things. I washed our comforter on Bulky. The part that must have been at the bottom is completely wrinkled and it also wrecked all of the fill. This was a comforter that it is supposed to be fine to put in the washer. I am attaching pictures in which you can almost plainly see where the comforter was at the bottom. I had a serviceman out a few weeks ago. He said Maytag knows that there is a problem, however, there is no service bulletin that is out yet on it. In addition, he ran all of the codes and told me there is nothing wrong with my machine. That must be why I have to iron almost every piece of clothing in this house. Maytag will hopefully give me decent customer service on this, or I will come unglued. For the price of this washing machine, I expected much more.

I love using my microwave because everytime I am in a hurry, like going to work and my kids to school and dont have time to cook or we dont like to eat outside fast food I cook healthy the night before and microwave it the next day and it just feels like the food is just made. It taste so good my kids and husband love it.

I bought this machine at Lowes because of the BIG drum area and about 2 years ago, it started to make funny noises; then I got the F-51 signal. I tried everything, shifting articles of clothing, then unplugging the machine and re-plugging. I am in the process of researching a plain Jane model, not one with all the bells and whistles. I am extremely dissatisfied and wish Maytag would step up to the plate and recall these machines. A motherboard and the costs for other parts, I would be better off replacing with a brand new machine. Dissatisfied!!!

My dishwasher is 3-4 years old and the control panel is malfunctioning. Cant push a button to choose what cycle I want, it doesnt respond. I went to the Maytag website to see if there have been others with this problem. It appears that there are many other people having this problem. Parts are not available and it seems that Maytag wont do a recall on this product due to the control panel malfunctioning. I have been dealing with this problem for the past few months. I dont think Maytag is worth the money. They want if you only get a few years out of them.

I bought a Maytag laundry set (washer and dryer, models MVWC565FW and MEDC555DW, respectively), and I concur with the fact that this is the WORST laundry set I have ever owned. The clothes came out of the washer extremely dry and did not come out as clean as expected. In addition, clothes came out with strange spots, especially the dark ones. Now, we wash our dark clothes with fear of damage them. The dryer is also pathetic. I put in a normal load on high for 60 minutes, and theyre still very damp. Sometimes I have to repeat the cycle 2 or 3 times. When I compare it with my old laundry set, this is extremely disappointing. And to make things worse, the customer service department doesnt answer you. I sent them a mail, on February 2018, and a month and a half later, I havent heard back from them.

The Maytag Bravos washing machine may well be the worst appliance available for purchase. Sure it is a high efficiency machine that saves on water -- the clothes are often still dry when the complete cycle is finished. Many times there is still soap residue on the clothes. Forget cleaning anything with any amount of dirt on it because it seems as though items are even more filthy after washing them. I have tried everything the company advised and still my clothes are not clean. My advice... please do not purchase this machine. You would be better off taking your clothes to a river and beating them on a rock. #wearingdirtyclothesforever

I purchased a new Bravos X MVWX700XL2 silver gray washer and dryer in May 2013. I have been unhappy from the beginning. Junk! Waste of $1200.00 - 2 inches of water will not cleanse clothes. I found that the bulky setting gave more water so I run most of clothes on bulky. Now for the past 6 months there is a very loud grinding noise while washing & rinsing. So loud my neighbors have commented on it! When I remove them to put into the dryer they are all twisted and a few times clothes have been torn! How can a product of this sort be sold? I have always trusted Maytag but this has me going in the opposite direction. I spoke to the department manager a year ago and he said nothing can be offered. They didnt seem to really care. I will be part of a Class Action Suit if possible. I plan to continue to make people aware of this along with the Better Business Bureau. I am signing this: ANOTHER UNHAPPY MAYTAG BRAVOS PURCHASER.

We purchased the Bravos XL washer just over a year ago. It is being replaced 1/10/2017. Simply put this is the worst product I think I have ever encountered. Extremely noisy wash cycles leave residue on the clothes, clothes do not get wet in some spots. This washer is so noisy you can hear it from outside. What an embarrassment. You have to run the clothes twice first with detergent and again without detergent to remove the residue left over from the first wash cycle (not energy efficient at all). If I could give a minus score like minus 10 I would.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

Like other reviewers, I am having issues regarding the control board panel for MAYTAG Dishwasher Model Number MDB7749SAM0. The unit was less than 3 yrs old when the control board panel malfunction issue began. I feel like this is a manufacturing defect and the company should be responsible for repairing/replacing the control board panel. I contacted Maytag numerous times regarding this, but customer service continues to tell customers there is NO warranty after one year from purchase date, and they are saying there is no recall or other reported issues regarding the Maytag’s control board at this time. However, I have found numerous online complaints and reviews about the very same issue I am having and same poor customer service. Since MAYTAG does not seem to care about their customer’s concerns regarding their product breaking in I feel that the only solution is DO NOT PURCHASE MAYTAG dishwasher brand again. I have had other brands last much much longer than this one did.

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

Maytag Dishwasher with model number MDB6701AWS and Serial Number 41687985NJ.It does not clean dishes like it should. We tried every possible way to set control settings, and still the dishes come out dirty and spotted. Also, it doesnt dry like it should. We had a Kitchenaid before we moved and it worked great.

Our 26 month old Maytag fridge (Model MFF2258VEM8) was the french door freezer on bottom modern style fridge. The freezer stopped working. The repair shop took the fridge away and repaired a leak (quality control issue) and then the compressor failed in a test. They wanted $700 to make a repair that would have a 90 day warranty about 1/2 the cost of the fridge. Maytag was contacted at multiple levels and they would not even provide a free compressor or provide a substantial discount on a new fridge. What a way to treat a customer who once had all major Maytag appliances in our home. We decided to get a GE Profile fridge and are very happy with it. I will never buy another Maytag appliance. I dont think it is the great company it once was years ago.

Our washing machine is 3 years old. About a year ago we started to see hairline cracks on the plastic lid in the bottom corners by the hinges. These have now become huge and pieces of plastic are breaking off every time we do a load of laundry. Maytag (under the Whirlpool brand) will not replace the lid for us. We paid $130 for a tech to come out and confirm what we already knew - that we need a new lid. And now the parts and labor will cost over $550. We have called customer service several times and spoken to a supervisor and the best they can offer us is to pay for the part which still leaves us to pay over $400 out of pocket to repair a $600 washing machine. This seems to be a common problem and is all over Google, yet Maytag is not willing to help their customers.

We like the refrigerator and we have had it several years. But the thing the top freezer conceals much of the top rack of refrigerator. We must duck and almost kneel to get to food inside. Next fridge will have drawers and doors that open on both sides.

I am angry at my Maytag! It sprays water on clothes that is not enough to soak them or let the detergent to be dissolved especially for towels. Hopelessly, I Hand Wash my towels, rinse in tub then just put them in the machine to spin. BAD BAD :( :( Is it possible to increase the water amount?

Maytag washer has increased my water bill; it was supposed to be energy efficient! Also, the washer will not wash a blanket. Sensors will move a large item to one side causing an uneven load which then causes numerous extra fills until stopped manually. I was told to add more items! A blanket barely fits in the tub. I had to invest in lint rollers since the rinse cycle is inefficient. This washing machine is useless. I should have stuck with Kenmore.

I bought this after having a Frigidaire for 40 years and was immediately disappointed upon installation. This OVEN, not a range, was smaller inside and a lot of new pans would not fit! I have replaced the burners and the bulb wiring several times. Would not buy another one!

My refrigerator stopped working less than two weeks after purchase. The ice maker failed to produce ice. I feel they sold me a lemon. Yes, I do!

Bought the Model MZD2766GEW and the MSD2454GRW side by side models of the Maytag side by side and the wide side by side from Home Depot in the year 2002 replacement appliances after a fire. For both units I paid $2526.92 dollars plus tax to put one in my kitchen and one in my basement. I was told by a plumber Maytag was the best, buy Maytag. It seems like from day one things went wrong. The ice maker kept building ice in the bottom of both freezers. The ice maker never worked right and would build up so much ice in the dispensing area, you would open the door and ice would fall all over the floor and you would have to take a knife to the shoot of the ice maker to unclog it. The drawers would freeze, the vegetables and anything in them, you had to keep the refrigerator temp to Zero and things would still freeze. Water eventually would leak all over the floor and I couldnt figure out where it was coming from. The freezers on the left but then water seem to be running to the right and out the refrigerator part. I couldnt afford to call anybody and the warranty was running out. I had 2 year parts and one year labor but at the time couldnt afford the service call charge. Eventually I was sent a recall notice for a compressor or such. I thought, Hurray, It will be fixed. Not at all. He replaced both those parts on both refrigerators and after he left it started leaking again. I called Maytag and they said, did he replace the part that was recalled? I said yes and they said They were not obligated to pay for anything past the recall. I should call and have the units serviced by a technician at my cost. If he says its the recall piece again, to call them back. Again I had no money to call a technician right away but when I did, he came to the house, told me it wasnt the recall and claimed to fix some kind of defrost sensor which cost $180.00 for the parts plus labor, plus service call and this had been a different technician than the first. He left and the problem continued to leak, freeze etc. In fact it seemed worse. I gave up calling and decided to deal with it hoping one day to replace but money problems happen and it is now 2014 I never could afford new refrigerators and have had to put up with the leak for all these years and continue to pick up and replace soaked towels everyday. In 2005 I disabled the ice maker which helped when I opened the door since ice doesnt fall out but both Refrigerators continue to make thick sheets of ice on the bottom and food is frozen into it so I cant use the bottom and when the buildup gets so bad it takes 2 days to defrost by shutting the entire unit off. All I can do is put my food in one freezer and refrigerator while the other defrosts. I also have turned the downstairs one off completely. Now as a second refrigerator I just dont trust keeping it on leaking also. I bought these units after a whole house fire and the last thing I want is another fire because Maytag just doesnt care but I cant afford new Refrigerators because these repairman and Maytag cant figure out whats wrong and fix the problem with this dangerous feature and I call it that because it seems to come with most of their units from when I bought the unit till now.12 years later people are still having the same problem with the same and copy cat units. Maytag, a plea goes out to you to recall and repair these units. The original recall did not work and like me a lot of people need to be redeemed for what you left go on and a lot of repairmen are ripping off people calling this problem what its not and stealing our money when you know what the problem is and can fix it. My plea is recall this problem or be responsible before God or who you believe in for letting it go on so long and the damage it may cost people. Maytag, people use to love you but youve ripped our hearts out and it will cost you in the long run.

I made the mistake of buying a Maytag fridge and dishwasher when I moved into my home 16 years ago. Ive had nothing but trouble with these inferior appliances since almost day one. The seals on the freezer quickly started to separate, causing ice chunks and insufficient temperatures. We had an extended warranty, but they refused to replace it. Weve had that fixed approximately 10 times - never resolved it. The plastic covering on the dishwasher racks began to peel early on, which caused the metal underneath to rust, in turn causing the clean dishes to come out with little rust flakes all over them. This company obviously cares only about profits. Save yourself a ton of headache and DO NOT BUY MAYTAG.

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

This was purchased 3/25/2010 with the Home Depot Service Contract thru 3/2015 . We have already had a service call in 2013. We were OK until January 2015. Now we join many other customers with the leaking defroster. We have taken all the steps of the other customers. We went and called for a service appointment. Weve spoken to Maytag Customer Service 800-253-1301. Ive asked if there was recall? NO! I asked if there was log made of my call, NO! Any work done had to with Maytag Authorized Repair Person. The Home Depot Contract use a Non-Authorized Service Person. Weve gone to Home Depot. We are in a catch 22! We have spent good money on this refrigerator. Out of sight, out of mind. We will go back to Home Depot Again!

I purchased Maytag refrigerator (model # MSD2572VES). The fridge side stopped working. I was told that the vent/chute between the freezer and fridge ices up and prevents the cold air from the freezer to go through the fridge. The tech said that Maytag was sending him a tube of silicone to apply all around freezer and fridge and that this will probably fix the problem. So in other words, because of a design flaw, the refrigerator cannot function without adding silicone (maybe). I believe I purchased a lemon with a design flaw and they want me to accept a permanent band-aid as the solution. Shouldnt I have right to demand another model instead of having to accept a cheap alternative (silicone)? Now, if factory installed parts break off, can you imagine silicone tubed in after the fact where there was no silicone crevasse? I cant imagine it staying on - permanently.

Washer knots clothes into unmanageable tangle. Poor rinse leaves soap scum unless rinse extra, thus not conserving water as appliance is supposed to do. Load easily becomes unbalanced and unable to restart machine if paused to rebalance load. Will never buy another Maytag washer or dryer.

Purchased the Maytag Bravos washer from Home Depot in August of 2011. Today it caught on fire (Sept, 2014). Had problems with it from the start. Some of the issues include the washing machine constantly getting off balance even with small loads, not completely draining the water from clothes resulting in having to run additional spin and drain cycles, and a bad odor coming from the water that stays on the clothes (we even called a plumber thinking it was something with our plumbing). Well today was the best. I started a small load (one twin flat sheet and a pillow case) and about 10 minutes later I smelled a weird burning odor coming from the laundry room. When I opened the door to the room it was filled with smoke. The washer was the only appliance running, otherwise I would have assumed the dryer was the source of the smoke. When I opened the lid to the washer, smoke started pouring out from around the inside drum of the washer. It smelled like burned rubber and ash. Needless to say, I doubt this washer is worth repairing. We actually have had repairs on it previously (twice in the first year) and its just a piece of junk. Glad I was home when the washer caught on fire. I hate to think what would have happened if I had not been able to unplug it and it continued burning. Do Not Buy This Brand. Definitely do not run this washing machine unless you are home to monitor it. Maytag Bravos is a fire risk!!!

Purchased the Maytag Bravos washer and dryer at Home Depot. Previously had a Maytag set that was 25 plus years old that still ran well but was rusting out due flooding. Figured Maytag had great products. Have had mine for 4 years now and had nothing but trouble. Paid countless service calls, mainly on washer, will work for a short while and then stop again. Cant put more than 4 towels, or 3 pairs of pants or basically anything or the codes start popping up. I am so angry that a product I paid a lot of money for is such a piece of crap. Maytag Company has been no help and I see with all the complaints on this site I am not the only one who feels this way. A class action suit would be great!

A contractor purchased the Maytag MDB7609AWW2 dishwasher about two years ago. Sometimes it will start a load, but most times it will not. The light for high temp, heated dry and sanitize work, but the heavy, normal, light indicators will not light up. Im faced with either replacing the control board or control electronics. I was told Maytag is a quality product. I have not abused the product. The last dishwasher that I had lasted 10 years. I only purchased this one because of a remodel. I will most likely replace the control board since thats the defective part. It doesnt give me a good feeling about replacing the part since it’s obviously a defective part. I will consult Consumer Reports before purchasing another dishwasher.

Sometimes the control panel is difficult to work with especially if the wash is paused to add more clothes or detergent. The good things is that the tub is very large so a comforter can be washed and you can control the amount of water depending on the amount of what is being washed. I also like that it doesnt have the big agitator in the middle.

In December 2010, we purchased our Maytag Quiet Series dishwasher model #MDBM601AWB3, serial #NY2916421. At first the sanitize light quit working about 6 months ago. Today, September 30, 2012, this piece of crap will not turn on at all. There are no lights on at all. We paid almost $600.00. As far as being quiet, oh yes it is quiet alright! We the consumers are demanding a recall. Look at the complaints! Its a manufacturer defect in these control panels. I will not be forced into buying another dishwasher or a control panel. I want this company to stand up and say theyre sorry and fix this problem for all of us Americans!

I have had my Maytag Bravo for 5 years now. I originally paid 1800.00 for the set. And yes that is without the tax. Well I also got a warranty. Three years after I purchased my set my dryer stopped drying my clothes. I called the warranty company for a repair man and lo and behold my warranty is over. The repairman came and said that my lint was backed up. He stated that it was a good thing that I called when I did because they have been known to catch on fire. I asked him how is this possible? I check my lint screen and clean it after every load. He stated that the lint falls off the screen and just settles at the bottom of the dryer. And sometimes the dryer will get so hot that it will actually set the lint on fire. He fixed it but now it is back to doing the same thing two short years later. Im thinking that Maytag must know about this now and I am wondering why they havent did a recall on these before someone gets hurt or even worse by trying to do laundry.

This machine was purchased two years ago at the Home Depot. I wanted a top loader that was not digital and without a lot of choices. It has been nothing but a headache with every wash. I had a Maytag serviceman come out immediately and he said nothing was wrong. Every wash load I do, has problems. The dark loads are always full of white spots and the towels are torn up. Just bought some new towels and after the first wash, they were ruined. I will never ever buy a Maytag machine. These new He machines are ridiculous! I no longer have a receipt, but the complaint should help consumers in their decision to NOT buy a Maytag machine.

We purchased our Maytag Neptune washer and dryer in 2006. Months after our purchase, we tried every HE detergent we could find to see if our towels would smell fresh. Nothing we have tried has worked. I just went to Maytags web site. I found out there was a recall on this washing machine due to the mold on the door gasket. Why didnt they send me a recall notice so this could be corrected with a refund or something?

Sheet of ice in floor of freezer. Leaks water from bottom, and now ice crystals in freezer! French door MF12569VEA1.

This washer has no agitator post and doesnt seem to clean as well as ones with agitator posts. I have heard that they are easier on your clothes though. The dryer works well enough, but I believe the control panel/motherboard needs replacing. The signal sounds even with the dryer turned off, which is startling to my dog and me. I reset it by flipping off the 220 breaker in the garage and leaving it off until the next time I do laundry!

High dollar front load washer, less than 2 years old, just a waste of time & energy to run it, clothes come cleaner, if you leave them out in the rain! DONT buy Maytag, I never will again!! The customer service SUCKS even more than the product, 3 hours of my life spent today e-mailing, calling, live help, NO response? They must have shut down customer support due to the overload of calls from UNHAPPY customers!! NEVER again!!

I bought my Maytag dishwasher MDB7749SBM0 three years ago. After it was in one month it already needed a service call. It needed a control panel. Out of the dishwasher 4 weeks because this happened over Thanksgiving. Two months later it stopped working and needed another service call. Technician was inexperienced and another one had to be called. Out of the dishwasher 3 weeks. At this time, and because of the expense of the machine, I purchased an extended warranty. This was control panel number two. Not long after, the heating element had to be replaced. Two weeks without the dishwasher. Now, my dishwasher stopped working again and it needs a new control panel. The technician is rude but did offer the information that the moisture ruins the control panels. IT IS A DISHWASHER!!! IT USES WATER!!! I only run the dishwasher twice per week so I cant imagine how poorly it would hold up if it was run more often. I am on my third week without the dishwasher because the part is on back-order! No one can tell us when it will be in. I bought a Maytag because I thought they had the appliance market under control. MY MISTAKE! I am very angry.

Washer purchased in May 2013 last month it stopped completing the drain and spin cycle and cloth stayed wet. To have the machine repaired, we would have to replace the control panel. The cost of replacing the control panel plus the service call was 76% of the cost of buying a brand new machine. As such we are disposing of the machine and will be purchasing a competitive product.

My dog had to be on a special diet to recover from a stomach disorder. I placed 1/3 cup of dog food plus chicken broth and baby food in a bowl. I intended to heat it for seconds. Minutes later, my dog was whining and sneezing. I immediately returned to the kitchen to find the food and bowl were completely charred. The biggest problem however was from the plastic splash guard that melted down. Smoke filled my home. I had to call the fire department. I was coughing and had difficulty breathing. The smell was horrible!The insurance company and I have had thousands of money in restoration cost due to the damage. I was out of my house for weeks and got very sick due to returning to the home that was not remediated properly (allergies and asthma). The microwave was an over the range Maytag MMV4205BA. I would like to find out if the fire was due to a malfunction in the microwave oven. If so, Maytag should be paying for the damages. I still need living room furniture and carpeting replaced due to smoke damage.

I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

I bought this washer less than 4 years ago and its already broken (leaking from the basket). Maytag refuses to honor their warranty and is charging $400 to send someone out to fix it even though it specifically says in the warranty that the basket is covered. When I mentioned this to the rep, I was told that does not apply to all washers. I expected better service from Maytag and thought it was a reputable company. I will now have to purchase another washer, rather than spend $400 to fix this one. It definitely will not be a Maytag!

I purchased a Maytag dryer #MEDB400VQ for $715.48 along with a 5-year warranty for $119.99 on March 30/2012. Since then, the dryer has broken six times. Our warranty stated that after it breaks 3 times, we would get a new dryer. All claims for a new dryer have been denied. The dryer is still broken, going on 10 days, only to find out that parts needed are on back order for two more weeks. This is unacceptable! I will never ever buy a Maytag again and will tell all family and friends my story so they do not purchase a Maytag and go through the hell that Maytag has put my family of five through!

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

Maytag washing machine Model # MHWE500VW - 2 control boards only last 4 years. I paid top dollar, $1229.00 to be exact and the parts and labor are $659.00 with no guarantee that there wont be further problems. Technician told me that this is typical of Maytag products. Contacted Maytag and they told me to take a hike and have a nice day. I will attempt to get some help from the place of purchase, Hamai Appliance, Maui, Hawaii.

Just purchased/used the washer. One needs water to wash clothes. I added water to the machine just to get the clothes washed. How can this pass any reviews when it does not use enough water to clean a set of sheets? Not to mention rinsing. Does anyone wash clothes in the group that designed this machine?

It leaves white stuff all over everything. You have to rewash or rinse black clothes at least twice. We have to clean the washer frequently or the clothes smell like mildew. I chose Maytag because I thought they were the best. Apparently, I was wrong and it was a mistake buying this.

I unfortunately just had the same issue concerning my unit. The unit went berserk, stopped cooling and ruined all my food. I managed to get it outside after leaking spoiled food all over my floor. I washed it out and contacted Maytag after reading the hundreds of complaints. They sent someone out to fix the panel but he couldnt get it to cool. He said many times when a unit goes down that the acidity from produce along with moisture can eat through the aluminum components causing a freon leak. Obviously, this happened to me. I contacted Maytag and they said they would fix that too but once I called back, they said that it was a separate issue. Then I spoke with another person who said they would send a tech to inspect. I took off work and finally got a courtesy call from tech saying he was told not to come. I was amazed I missed work waiting and got no call from Maytag saying they changed their mind. I called back in and was told flat out I would not be covered, even though the fridge was fine before this happened. I suggest everyone read over the Consumer Protection Act which covers defective equipment causing issues by both injury and property damage. A class action lawsuit needs to be organized concerning this also. In the meantime, I implore each of you to file a complaint with the Better Business Bureau in your state along with Michigan where Maytag is headquartered. This will guarantee a response from corporate. Also, make copies of this forum and send it to your State Attorney General explaining how you have been sold a defective item. They say ABC news once did a segment on this fridge issue also, so I suggest contacting them asking for a follow-up story. For those that use social media, go onto their Facebook and Twitter page to post a link to this site and the way you have been treated after spending over $2,000 and a fridge that has lasted 7 years or less. Its time for small voices to unite to form one that is much larger.

The dishwasher doesnt clean and the dishes and silverware come out greasy. What a piece of crap.

I purchased a Maytag Dishwasher (MDB7749AWW1) just over a year ago from Sears. I did not get an extended warranty since the appliance wasnt over $1,000 and I thought I would take my chances. Sure enough, about one month after the warranty expired, it all falls apart. There is something wrong with the control panel and I cant get anything to work. Ive been looking online and see that this is a common problem. So rather than throw more dough into the money pit, Im purchasing a new, simple, uncomplicated GE Americana washer from Home Depot for $279. I figure this will cost me less than going through the repair dance with Sears and Maytag. I will never purchase an appliance from Sears again. Ive been through the mill already with a $2,000 Jenn-Air range that has broken down five times in the past three years (2 times it was the control panel). I was lucky that I purchased the 5 year extended warranty on that one, but never, ever again will I deal with Sears.

My Atlantis dryer has never been able to be used on more/less dryer settings, I have had 4 repairmen repair my dryer 3 were while dryer was under warranty to fix the same thing 3 times wiring 4th time, anyway last repairman said my More dry wont work because I never had a sensor installed in my dryer and there is not a place for one so since 2005. Ive used timed dry only or my dryer runs all the time. I am concerned the first 3 repairmen never caught this. I should not have to be responsible for this either. Please have a manager contact me and have them check into my Atlantis Maytag dryer bought in 2005 and all the repair slips sent to Maytag.I used Green Yates in Joplin. Pretty sure. I thought I just had to live with it they would put new parts on I think timer, thermostats anyway can someone tell me for sure or inspect for yourself. I am single and dryer never used that much. Concerned Consumer, Nancy **/ Nancy ** as that name had front loader set from Maytag that I was very pleased with but sold with home in KC area, wish I had that set again I was very pleased .Thanks for your time.

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

I have had it (Model MDB6000AWB) for a few years now. It had to have the door replaced per recall. This dishwasher does not wash dishes well at all; need to rewash many items after going through normal wash cycle. Also, all spokes are burning and falling off, along with pans getting burn marks. I am not sure how safe this is anymore. I am going to purchase another dishwasher, but not a Maytag!

At first the Maytag Bravos XL top load washing machine met all me expectations. After 3 yrs. the top where you load bleach and fabric softener began to rust. This is not covered under warranty. My last washer was a Whirlpool and had it 15 year and never had that issue. So it cant be from the water, just poor workmanship. Very disappointed. Now my lid came loose and is ready to fall off. Would not recommend.

We bought a new commercial Maytag washer. It’s deep, it has the agitator, suppose to be the top of the line. I can do sheets and the top ones are dry when done. It doesnt get clothes clean especially if they are really dirty. So I add water to this wonderful machine——anyone wanting pictures of finished clothing I would be glad to send to you. Dirty jeans come out dirty jeans. If I forget and don’t add water it’s worse. So I watched it. It fills up to maybe halfway on clothes and this is on heavy soil and deep fill. I complained about it at the store and was told “he had one and it did fine” and you can’t get any that do any better.

We have a model MF12269VEMS. Approx 3 years old. Ice maker and water dispenser work great. Fridge works well. We have experienced over the last 6 months a buildup of ice that forms inside the freezer under the drawers. If we dont catch it every 4-5 days we cannot open the drawers as the ice catches the bottom plastic drawers. I called Maytag directly and the pleasant young lady told me after checking that it did not seem to be an issue...clearly after looking into the internet I am not alone! Maybe someone can email me a fix?

Bought a Maytag Front Load MHW6000AW washer and had a problem with amount of water in wash cycle. Dealer sent service men 3 times and changed several parts but washer still did not work and both repairmen said they did not know what was wrong. They called Maytag Tech Support but those people did not listen and said if no code shows up the machine is operating properly. Maytag then sent another company repairman. He worked 2 hours and said he could not find the trouble and Maytag support hung up on him. Maytag then sent another company repairman and he did one test and said the machine is fine and left in about 15 minutes total time. Now Maytag refuses to send another company for another opinion but I have a $1200 machine that still does not work properly. I am totally dissatisfied with Maytag and will stay away from their products totally. Companies wonder why people buy foreign equipment and this is the answer. I had a Samsung washer and never had one bit of trouble with it.

I bought a refrigerator from Home Depot in July 2013. In late November 2014, I noticed water on the floor in front of the fridge. I called the Maytag customer service and reported the problem.. The customer service rep explained to me that Maytag discovered a design flaw in the part that allows the water to drain when going through the defrost cycle. I also called Home Depot. Their response was it was my problem because the fridge was out of warranty and I did not buy an extended warranty plan. After two more calls to Maytag, they scheduled a service appointment. The service repairman told me the same thing about the design flaw. I have the old part and the package the new part was in. The two parts are completely different. I requested that Maytag or Home Depot replace the fridge or give me credit for the amount I spent. Maytag is now saying there was not a design flaw and because of that, Home Depot refuses to replace the appliance. I will never buy another Maytag product or shop at Home Depot. The extended warranty is a way to place the responsibility directly on the consumer and eliminating the responsibility of the manufacturer and the store.

I was repairing this Maytag Maxima washer and was almost electrocuted. I simply grabbed the wrong screws which were too long for the door switch, one screw went through into the open/close switch and contacted voltage, thus causing a direct short to the chassis and me. It also damaged my control board (the most expensive one in the industry), now Im out an extra $220 because Whirlpool made an engineering error. A screw should not be located so close (millimeters) to a voltage source where a simple mindless mistake could cause electrocution and possibly death. As for the washers operation, the drain pump failed after just two years, it sometimes leaks water out the front because debris gets into the boot drain back holes. It smells like mildew even though we leave the door open, my clothes stink, Affresh is costly and really doesnt help much. It does a decent job of cleaning, not as good as the old top loaders but it saves water. I think next tax return time this machine goes up for sale and we get a better machine.

My dishwasher racks are disintegrating. I called to see what to do or if there was a recall. I was told that problem happens a lot, but there is no recall or other option other than to purchase new racks. I could almost buy a new dishwasher. I bought Maytag so that it would last a long time with few repairs. That has not been the case with this dishwasher. I had a medium grade Sears’s dishwasher for years before I supposedly upgraded to a better dishwasher. Maytag is obviously an overpriced name and the quality of their product is no better than any other cheap dishwasher.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

We had a Whirlpool stove/oven for many years, and it was finally time to trade it in. Everything about that unit was good. While shopping for another Whirlpool, the sales rep told us that Maytag and Whirlpool are one and the same. That we found, is false. An important feature for us in an appliance is the self cleaning oven. The Maytag oven had to be leveled four times after it was installed, in order for the self clean feature to function. The self clean part is only a small indented portion of the bottom of the oven, not the entire oven. And even that does not clean. After going through the dealership service about this problem, I contacted Maytag. My final frustrated summary to the rep was that I understand that we bought a lemon, and you are not going to help us in any way. I just want to say to anyone considering a Maytag stove and oven, raise your standard. If you choose Maytag, you will only be disappointed. I am.

CONSUMER BEWARE: Maytag is the WORST corporation to deal with. We have purchased a Maytag range from them recently. Unfortunately we have had 4 appliances delivered to us damaged from Maytag. The fourth time around we finally got a supervisor on the line. In order to expedite the situation. And the supervisor (Frank) refused to expedite or even call to try and move up the 5th delivery date. All he talked about was Maytag company policies to us. To make a long story short and I do mean long. Buyers beware. Maytag DOES NOT HOLD THEMSELVES ACCOUNTABLE FOR ANYTHING. Once the appliance leaves their facility they are not responsible for it. I CANT SAY THIS ENOUGH. DONT PURCHASE MAYTAG PRODUCTS.

Works quietly and efficiently and I love it! I dont even know its running and the dishes are sparkling clean when they come out. How could ask for anything more. I would always purchase this brand again. The reliability is another factor, I have had Maytag before.

Purchased dryer less than 6 months ago and now have an issue with the powder coating bubbling up and flaking off on the dryer drum. Maytag says not covered under warranty unless found in less than 30 days. If I had know that I would not have purchased the dryer.

I purchased a Maytag top-load washer 16 months ago. I had a problem with it four months after purchase and they told me it was not leveled, which I did not believe. I set it up as the manual said to. The washer left clothes soaking wet about every 30 loads. I continued to use it and the washer finally quit working after 16 months. The repairman found the nut which holds the pulley on the shaft that turns the drum had been loose and had been this way for some time. $129.00 later, it was fixed. It works fine now. I wonder if this problem should have been caught on the first service call when it was still under warranty.

Maytag French Door Fridge Model MFT267AEW10 - Not even 1 month out of warranty and the water line solenoid is leaking. It seems the water line installed at the factory was pulled so tightly that it has caused the solenoid inlet to start leaking. We really researched this refrigerator and thought we were buying the best. Not so, Maytag wont warranty it. The last purchase of Maytag I will ever make. We should have bought the Samsung but we were trying to buy American. Wont make that mistake again. Not a smart investment. Refrigerators are supposed to last a good ten years. How sad.

After 16 months my Maytag dishwasher control panel went bad. The company told me they could not help me. I asked for a new control panel to install myself, no luck. I bit the bullet and bought one online for 110 dollars. 2 months later... you guessed it, its bad. Now I have to send it back under warranty. It was a Maytag name brand OEM part. I thought Maytag was a reliable name, I thought wrong. Never again.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

I bought a brand new Maytag bottom freezer fridge on Aug. 12th, 2012. The main compressor went out on Memorial Day of 2013. I contacted the store I bought it from; they referred me to a local repairman who fixes Maytag. I talked to him and told him the problem along with the make & model of mine. He ended up telling me what exactly the problem was, & there were about 5 people ahead of me with the same fridge, & same problem... all main compressor problems. Check this out. The compressor part is on back order... so now I have no fridge, & Im stuck with this piece of crap, until MAYTAG finds a compressor to ship to the local repairman. - Last Maytag product I will ever own in my lifetime!!!

Purchased Maytag Model MVWB865GW0 Ser# **, had it ONE year, circuit board and switch have gone bad, will not turn to change the type of wash cycle and the lid will not lock, which makes the washing machine not start to wash. Contacted Maytag to request a service call, per the service team the circuit board will cost $300, plus a switch $75 and Labor $100 plus tax. We will be better off buying a new washing machine! We should not have this high cost within ONE year of purchasing! Will not purchase a Maytag again!