We purchased the Maytag Atlantis used (4 years old); it looked like new. When I opened the lid, I noticed a terrible smell like some left the clothes in the washer for days. I used white vinegar, baking soda, bleach, anything to try and get rid of the smell. Nothing worked. Finally, my husband took out the agitator and then the drum. Inside and around the drum was lint from all the years of washing clothes. He scraped it all off and bleached it and put it back together and it was okay for a while. It now smells again and I am afraid we will have to keep doing this or our clothes will always smell. I also leave the lid open after a wash so Im not attacked by the smell when we open it. I also had the Maytag Neptune front loader years ago, and the water pooled by the gasket on the door. That smelled too! We will be redoing our laundry area soon and will be shopping for a new washer and dryer. It will not be a Maytag!

Horrible machine. Uses too little water, cycles are too long. No matter what the size of the load, it takes an hour. Just after 3 years the bearing went out on the machine. Cost for repair will be $250. Thats not even an electronic problem which Im sure would be next. NO THANKS. Im getting a new machine and it wont be a Maytag.

The washer doesn’t have enough water to to get clothes clean. Even on deep water wash there’s is not enough water. It doesn’t get clothes clean, its very noisy. It takes a long time to was, even on short cycles. You can’t soak dirty clothes, it has a cycle for soak but it is not long enough. After about 3 months the lid licking doesn’t work and the progress lights remain on and never go off. This is the worst washer that I have ever owned. I just want to return it and get a different one!

Duck bill valve for defrost water from freezer malfunctions, water flows into freezer freezes, then eventually overflows onto floor. Huge problem for folks with wood floors. Also a slip/fall danger especially for the elderly. When the repair line is contacted, they deny the problem and say you are the only one. But if you do your research, you find there are hundreds of complaints and in November 2013 they issue a service bulletin, but its internal, not meant for consumers to find out. So if you have this problem, go to the Consumer Product Safety Commission and fill out a complaint. Maybe then something may come of it.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

We built a new home in 2008 and purchased a Maytag appliance package from Home Depot, including a dishwasher, stove and refrigerator. From the beginning, we had problems with our French door refrigerator (MFC2061HEW; it has been discontinued). Within the first year we had 3 ice makers replaced because it was not making any ice. Now, mind you, we went through Maytag to have their repairman to service our appliance and they set up all the service calls. We limped by for awhile and called a different repairman to come and check the fridge because it was not staying cold or making ice again and, of course, it was out of warranty. The first thing he did was check the freon and we were told that it didnt have enough freon to keep it going, so he recharged it and it worked great. We have had to have the repairman come back again this month because it stopped making ice and the temperature for upper and lower was all over the place. He checked the freon again and said the unit has a slow leak in it and he was unable to fix that. I contacted Maytag because I felt if the first repairman had checked the freon from the beginning, we wouldnt be having this problem. The only suggestion I got from them was call a company with a dye kit test and that they are sorry, but its not under warranty. I dont know about anyone else, but $2000.00 for a fridge that has been a pain since day one is a lot of money to replace. I feel they dont care about their customers and they should be responsible for paying for the repair that should have been caught from the get-go.

I purchased one of the first Impeller washer and dryer. The dryer is great, but the washer needed repair immediately. Home Depot refused to exchange the pair, so I will never buy from them again. The washer takes over an hour to complete the wash cycle, has to be set on Bulk in order to get enough water for a decent wash, and is extremely rough on clothing. Its made holes in some of my shirts and everything comes out twisted without enough rinsing. Sleeves are always turned inside out. Thats how rough it is. It costs me more in water and electricity. Neither Home Depot nor Maytag would replace the pair for me.

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

I bought this machine a year and a half ago. The entire drum and spin motor need to be replaced. Maytags warranty only lasted 1 year. I bought it at Home Depot, and also purchased the extended 5 year warranty. The extended warranty is as bad as the washing machine. I am now just 2 days shy of 4 weeks of trying to deal with both parties. Ive had to take my laundry in to have it done. The cost of the laundry, the cost of the machine, and the cost of the warranty is more than $200 more than what Home Depots Extended Protection Plan is willing to reimburse/refund. Home Depot does as much as Maytag when it comes to standing behind what they sell. An $800 washing machine only good for 18 months, really???

2013 We purchased from Lowes Maytag washer and dryer front load stackable. We live in a house 1890. We have a closet that these units go into so we are restricted to what brand we can buy. WE read the reviews. People must lie or are paid to write good ones. Within a few weeks the washer was giving us trouble. The door latch was not closing properly and it would take up to 20-30 min. to get it to start. Called and they said the latch was stuck. Again started having problems on and off. Months went by and had another service call. Same issue. Fixed it again. 2014 again same problem. We have to order a new latch and some other part. They could not get the part. Called Maytag directly and they were back ordered. What does that tell you. This is a major problem so much so that no one anywhere had the parts. 6 wks to finally get it and got it fixed. But in the meantime, the dryer was not working correctly. The clothes were damp and lint was all over. It was like a steam bath. They came out and when they looked at the back of the dryer it was burnt. Now this is what upset me. He said it could have caught fire and burnt down our house. Nice. The dryer was shot. They said to fix it would cost more than it was worth. Our warranty gave us a new dryer. 3 wks later I have my washer and dryer back working. In the meantime we have spent more time at the laundromat than at home. Brand new washer and dryer and are going to the laundromat. We had the dryer 5 days before it stopped working. Brand new dryer. Called and got a service call. The spring on the start button was not correctly put in. Who inspects these products. This was not right from the factory. So they fix it. Said if it happened again they would need to replace the entire thing. I do not know what that means. That was Dec. End of Dec. the washing machine is not running through the cycle. It had weird display on the washer. Thought maybe it was overloaded. Had to cancel and drain and then hit drain and spin. This takes not only more time but more electricity. I put in 2 sheets and it did it again. Had a few loads that ran properly and again it started. Called for service. He comes out and the motor that runs the belt to spin and some circuit board is shot. They call 2 days later and say that no parts can be found anywhere. WTH! It is 18 mos old and already the parts are extinct. So the warranty company said it was not worth fixing. They are giving us a new washer.I remember the commercials about Maytag that the repairmen had nothing to do. Well I thought it was because they did not break down. No... they cannot find parts. This is unacceptable. We have to go through the inconvenience of them not working and schlepping to the laundromat baskets of clothes. In the winter this is not fun. We are retired. Have to walk down icy steps. I have a washer/dryer upstairs and I cannot use them. Dont work. Not just the aggravation of dealing with repairs but not getting parts available, then having to wait to get money back to order a new washer and dryer and then get the dryer and 5 days later it doesnt work. Now we have to wait 2 wks for a new washer. It better work. Have to buy the warranty over again on each product cause they fulfill it when they buy you a new product. So this costs us extra money. The money we pay at the laundromat. The cost of electricity every time we have to run the washer 3-4 times to get it to spin out the water so I can dry them.To say I am upset is an understatement. I was told by a rep at Lowes, well Maytag has about 3 lemons a yr and you just got all of them. That was their consolation to our problem. I think Maytag needs to inspect their product. Our house could have burnt down. It is not a matter of parts going bad but damn the stuff is not even 2 yrs old. And the dryer was 5 days old when it stopped working. WE had a Maytag dishwasher and it was installed brand new and did not work. It had a defect in it. I never got to wash one dish in it and it had to be repaired. So I am not happy with Maytag. You go on Facebook and tell your story and all the Maytag horror stories come out. You need to do something to save yourself. Your company name is going down the tubes. Thought you should know this.

Bought a Maytag refrigerator model #MFT2673BEW10 in 2013 for $2100, the ice maker has leaked for two years. Paid for service come out and look at it, ice maker is shot, three years old, and it is junk. Tried to get help from Maytag Customer Support, what a joke. I was hung up on 4 times, and never did get any type of help except your unit is out of warranty. Bought at the Maytag Store in Saginaw, Michigan. No help there either. DONT BUY MAYTAG!!! They are junk!!!!

I purchased a Maytag Dishwasher #MDB7749SBM1 as part of a complete kitchen remodel less than 3 years ago. Maytag was a great product years ago so I thought I would switch from GE to Maytag thinking that I had purchased a quality set that would give me years of great service! What a bad choice to say the least! This dishwasher has never dried the dishes completely with heated dry option. I never cared for the plastic latch and metal catch option either since I caught water dripping from the bottom since the door must not have been completely shut even though the latch was secure.Most recently, the start option on the flat control panel will not work. After opening and closing door multiple times I can get the start option to light up and run the cycle. Added bonus to start option not working correctly is that when the dishwasher door is shut, it automatically runs hours later with no human interaction. The dishwasher lights were lit up like a Christmas tree at 7 am this morning and running a cycle. Guess it thought the dishes werent clean enough. I am going to price out a board and determine whether I will throw this piece of crap in the dumpster and find a different brand! I HIGHLY RECOMMEND THAT YOU DONT BUY A MAYTAG DISHWASHER!

This is the best microwave that we have ever purchased. I especially like the baked potato choice. Its also very easy to use and clean. I would definitely recommend it.

Our new refrigerator was pissing all over the kitchen floor. We had to disconnect the ice maker after an alleged repair part was supplied. (We had to pay a plumber to install it.) It didnt work, so we finally had to disconnect all the parts related to the ice maker. Here it is July, and ice cubes would really be appreciated right now. I get angry when I see all the Maytag commercials that pop up on the internet!

Maytag HE Top Loader Washing Machine: I have regretted buying this piece of garbage since my first wash. This washing machine is complete waste of money and a piece of garbage. The Auto Sensing doesnt work and doesnt cover the clothes with enough water. When the deep water wash is chosen the clothes just float around but the agitator doesnt get them clean. Dont waste your money hoping it will work, because it wont. Maytag used to signify quality that is no longer the case. I am going to also give a bad review to the place I purchased this piece of garbage because all stores need to discontinue selling this junk.

I have been on the chatline with Maytag customer service for two days, trying to enforce my warranty, which expires next week. My washer flooded my kitchen over the weekend, and I contacted Maytag to schedule the repair under the warranty. First, the woman, Aisha, looked up my registration, and confirmed that I was who I said I was, that my address and phone number had not changed, and told me that according to the records, the washer was purchased on 2/7/2011. Whats the problem? First, they wanted the model and serial numbers. I realized that this is important information in determining what machine needs what repairs, except there was not one sticker anywhere on my washer! Aisha said that the technician would not perform the repair, if the manufacturer did not install the model information properly on the machine. As if I had any control over the placement, or lack thereof, of proper ID for the washer. This was followed by a request for proof of purchase. I explained that I moved, and misplaced it, but I would have it emailed to me from the original purchaser. I was told that unless she could verify the proof of purchase, and the date of purchase, she could not schedule the repair under the warranty. This is despite the fact that not 5 minutes ago, she had just read this information from her computer! I asked her why would I register someone elses washer under my name and address? She didnt care. I told her I would have the receipt emailed the next day, and she stated that regardless of the date I requested, and scheduled the repair, if the actual repair took place after the expiration date of the warranty, it still would not be covered! I told her that makes no sense. I have no control over your scheduling issues. If you cant honor the warranty if the repair is made after the expiration date, then I need a date prior to that. I am entitled to the terms of the warranty, and intend to use them. Aisha said again that, without proper proof of purchase and purchase date, without proper tags on the washer, and if the repair takes after the expiration date, it would not be covered. I disconnected from her, and reconnected with another rep, who told me that some of the information Aisha gave was incorrect. I can schedule the repair, get the receipt and email it, or submit it through the chat, and regardless of when the repair was actually done, the warranty would still be honored. This person couldnt be sure what effect the lack of proper tags would have on that. My third re-entry into the chat was no better. I located a copy of the receipt in my email, and contacted the chat again. An almost amazing thing happened! This woman again confirmed all of the information Aisha recited last night, and was prepared to schedule the repair, without even asking about proof of purchase. This woman, Jennifer, was willing to schedule the repair, verify that it would be covered under the warranty, even if it was after the expiration date, because I had called and arranged the appointment before the expiration date, and she was willing to have the missing manufacture tags replaced. I had to ask her three times to review the email, and confirm that I had the correct receipt for the technician. I asked if the technician in the course of repairing the washer, had to remove the drainage hose, could he either replace it with a longer one, or add an extension, because according to Lowes at the time of installation, the hose they installed was supplied by the manufacturer, not them. Jennifer stated that since he was only there to repair the leak, and installation is not covered under the warranty, I would have to pay for him to replace the wrong hose, with the correct hose myself, even if he removes it! I told her that she needed to ensure that the technician absolutely did not remove the drainage hose from the back of the washer during his repair, because if he removes a part that is obviously the wrong part, and then replaces the wrong part after his repair, I would file a complaint every single place I possibly could. Why would a repair technician remove a part, determine that it is the wrong part, and then put it back! That is like a mechanic repairing the axle of a car, and discovering the brakes are bad, but since he is only there to repair the axle, he replaces the bad brakes after fixing the axle! He was going to be able to replace the missing manufacturer tags, though! This entire process took at least 3 hours and two days. To date, Maytag/Whirlpool is absolutely the worst company I have had to deal with, right after Sears, and ahead of AT&T. The consequences are that so far, Maytag refuses to have the technician replace the wrong hose with the correct hose, if he removes it in the course of repairing my washer.

After having had Maytag Highlander washer and dryer for 28 years in our early married life, and continuing to think that Maytag was a quality product, we purchased the Neptune front load washer MAH6700AWW. Let me tell you this IS NOT your mothers washer, nor is this Maytag a quality product. First it was necessary to install water pipe shock arrestors because of the water valve on washer causing shock in the waterline when it closed. The automatic Softener/detergent dispenser didnt work from day one.Coins and etc. constantly kept getting under flippers and couldnt be easily removed. I found that it was impossible to remove the plastic flipper without breaking a plastic mounting tab. On my first call to customer the Maytag Customer Loyalty Team, aka Customer Service (CS), I was told that the plastic flippers were not available as a separate part, and that the entire tub assembly with plastic flippers would need to be replaced. WHAT???????? THATS LUDICROUS. After temporarily securing the broken flipper to the tub, I thought Id call again about a week later to see if the previous answer was correct. On this call, the customer service lady (whose name I have), said the flippers are available and that she would send two at no charge. A few days later two flippers arrived, but were not the correct ones. I then decided to drill two holes in the tub and remounted the broken flipper with two stainless screws as a permanent solution.Two pumps needed to be replaced. One was replaced under warranty and one by myself. The one replaced by me was damaged by a coin that made its way from the tub to the pump. Other washer manufacturers provide a means of trapping such objects before they get to the pump. The wash cycle stopped unexpectedly numerous times without reason, after which the code 5d was displayed. I called Maytag Customer service. The representative didnt know what 5d code meant. Her suggestion was to call a service man. Again, I called later to ask and was told 5d meant excessive suds which wasnt the cause. Might this have been a control problem?There were three incidents of water discharging onto the floor from under the washer over the last two months, which caused water to cover an area of approximately 5 by 12 resulting in extensive cleanup in addition to damage to stored items. Since these occurrences were weeks apart and unpredictable, I knew the problem would be difficult, if not impossible, to diagnose, even by a serviceman. I concluded that it was probably a problem with the control; either filling too long or not emptying the tub before refilling for the next cycle. Thats when I decided to send this troublesome Maytag piece of junk to the landfill.

My Maytag range from the 1990’s is the easiest to clean top of the range I have ever had. Controlling the temperature of cooking is very easy. The oven is not as responsive As it takes about 10 minutes to preheat. Once heated it maintains an even temperature.

Purchased Maytag Bravos Washer in 2013. Used a little over a year and had to put it in storage for 2 years. Biggest piece of junk Ive ever had. Ive had cheap washers that lasted more than 20 years! Repairman said all diagnostics read normal. I put a very small load in to show him the water was not even wetting the clothes and only swishing them around a little. The shirt on top never got wet and was still in its same position when it went into the final spin. He said this is normal. He recommended I dump the machine and find an old NON Maytag model with the tall agitator!!! Ive tried using all the settings combinations; and the water level never gets all the clothes wet and clothes do not get clean. Will NEVER buy a Maytag product again.

I purchased a range 5 months ago. It is STAINLESS STEEL. It began to rust. I called customer service and they told me it was cosmetic, so they wont help. I think a stainless steel range should not rust after 5 months. Very disappointed, WILL NEVER BUY MAYTAG Again.

I started hearing the Maytag Microwave MMV4203DW00 beeping this morning after breakfast. I had not used it since the night before to heat up soup in a Corning Ware bowl. Its doing that 5E thing and nothing on the control panel works. Ive unplugged it, waited, plugged it back in and the same thing. It starts off saying Select Clock and 5E and then stops on the 5E. I bought this in Aug. 2010 and it is vented out the wall. Of course, that doesnt work now. The metal rack has never been put in it. Im single and the only one who uses it and I dont use it very much either. And this model only got the one 40-watt regular bulb over the range - lousy. And it doesnt work now either. And the control panel lights up orange. Had I known that, I would have never bought it in the first place. Of course, the stupid orange 5E lights up. Im unplugging it for good. Its not worth fixing. Do not buy this microwave!

I purchased both a Maytag washer and dryer and I am very disappointed in both products. Both appliances have electronic controls and are substandard. For the dryer if you do not touch the start area exactly right it will not start, can take multiple tries. For the washer, my town turned off my water to switch out the meter, once done the washer did not know how to clear the air in the lines and gave a LF error and no one at Maytag customer service could help me solve the issue and then could not set up a service call as their computers were down and did not have a process to call back the customer. This is terrible Customer Service - never again Maytag or any of their other products????

We bought this Maytag Bravos top loading washer 2 years ago after having bad luck with a front loading Maytag. Maytag was always the top brand to buy so I thought it was the style washer but now I believe Maytag has failed to keep their standard of quality high. My clothes come out of the washer almost dry and full of lint. Even though I use the HE wash soap, it does rinse out of the clothes. Dark clothes come out with a noticeable scum so I suppose the lighter clothes do, as well, I just cant see it. I sometimes have to wet the clothes down to get them clean and I always have to double rinse them which defeats the whole economy issue. Im not happy with this washer and would not recommend anyone to buy a Maytag brand washer.

We bought this Maytag Bravos 300 Quiet series top loading washer 3 years ago. Maytag was always the top brand to buy so I thought it was the style washer but now I believe Maytag has failed to keep their standard of quality high. My clothes come out of the washer almost dry and full of lint. Even though I use the HE wash soap, it does rinse out of the clothes. Dark clothes come out with a noticeable scum so I suppose the lighter clothes do, as well, I just cant see it. I always have to double rinse them which defeats the whole economy issue. Im not happy with this washer and would not recommend anyone to buy a Maytag brand washer. I absolutely HATE this Maytag Washer. DO NOT buy it. I would rate it less than one star however they did not offer a 1/2 star. If there is class action lawsuit please include me.

I purchased and installed a high end MAYTAG above the stove microwave. After 3 years of light use I hear an electric cracking sound and it dies. Of course no warranty coverage. Model MMV5208WB-1. I have to conclude MAYTAG builds junk and does not stand behind what they sell.

I saw something on your website about Maytag Neptune class action suit back in late 2005. I have owned one, never was notified of the settlement, and saw this since I have a mildew problem also in my washer. They are not willing to do anything about the repair on my machine, but send out someone and make me pay for it. Since I bought it in 2002, I would want to know why was I not included in the repairs and why wont they honor me in this since I am the machines original owner. Help, I worry that I am not having clean clothes and it is contributing to illness due to mold spores!

I recently purchased a new Maytag Commercial top loading Bravos from Lowes. It looked like a sturdy model and has a 10-year parts warranty and to cover this washer even more... I purchased the additional warranty from the factory. The washer is delivered, set up... First batch of laundry the washer is making all kinds of noise, the clothes are wet..water didnt dissolve soap packet... Repairman comes out..washer out of balance, cold water not at full pressure... Computer failure noted. Now still making a lot of noise, my clothes are twisted and intertwined and still dirty. My dryer isnt even taking the wrinkles out and even after I iron on hi steam the clothes are still wrinkled beyond belief... Im so dissatisfied with the washer... I want to return it... I cant believe Maytag would manufacture a washer that is ruining my clothes...

I have a 4-year old Maytag refrigerator. The back of the top freezer compartment is frosted and frozen, and the bottom refrigerator is now too warm to put food into. I wonder if a lonely non-busy Maytag repairman can come and fix it? Oh wait! Thats the deceptive false advertising that I bought into when I wrongly assumed that these were great appliances. I cant afford to get this fixed and after what Ive read from other peoples experiences, it wouldnt matter anyway. It would just break again anyway. What a joke! Ill unplug it and try replugging it in after it thaws and maybe that will work.

We purchased a high capacity washer (MVWB835DW), along with the matching dryer, two years ago from Lowes. This review is not about Lowes. They did the best they could to make things right. The review is about the Maytag washer (made and serviced by WhirIpool). It has been nothing short of a debacle. The first two washers did not work and had to be replaced. The third and current washer has been repaired three times, including the drum and motor. We have been without the use of the washer for over a week each time while waiting for parts and Whirlpool to approve the repair. The washer is not high capacity as advertised. Filling the drum even half way results in the washer stopping mid cycle whereupon we have to adjust the contents back into balance. In addition, the machine leaves a lint residue on dark clothing that has to be wiped off by hand. We have asked Maytag/Whirlpool to replace the machine but they say it has to fail for the same issue four times in order to qualify for replacement. We are done and will purchase another washer from a different manufacturer. It’s easy to understand why Samsung and LG have become such a dominate force in the laundry sector. Whirlpool/Maytag does not care about you or the problems with their product. Buyer beware!

We purchased a Maytag Jetclean Plus Dishwasher in June 2013. It worked well enough initially. We bought it because it had a large capacity and built in disposal. By August 2014, just after the warranty expired, the front panel gave out. To have someone even look at it cost $150. By following instructions from internet discussion groups by other people facing similar issues, we were able to get it to run in random mode. Programs were no longer indicated or selectable but dishes generally still got cleaned. Two months later a wheel fell off the premium rack glides. Finally after about 2 years of use, the dishwasher finally gave up altogether. At this point the stainless steel tub is no longer stainless. The entire device has worn poorly and looks shoddily made. This is the worst use of $900 I have ever made, and what tweaks me the most is Maytags attitude and their ludicrous warranty that barely lasts out the weakest link in the device.

We purchased a Maytag MVWX655DW1 Bravos MCT washer in 2017 and I recall a sloshing sound during agitation. Its a high efficiency model and was okay for several months, I think. It began to make something of a clunking sound during agitation that was similar to the deceleration sounds when the spin cycle completes. It seems that is an indication that something is wrong. Clothes arent clean after washing - another reason to suspect a problem. I observed the wash cycles and noticed that some items dont even get wet during the wash cycle. The clunking is probably an indication of the type of failure but I couldnt find anything other than someone else asking the same question when I did an internet search. Expected performance is shown in a company video with water sloshing during agitation. Thats the key take-away. My basket moves back and forth an inch or two during agitation and makes a clunking sound at each direction change. Water isnt sloshing through clothing and some of the garage rags that were once my clothes probably just needed a good washing. I suppose that even cleaning the washer isnt accomplishing much. The spin cycle is actually impressive. I load the washer evenly and find the completed loads with a towel or shirt evenly covering the clothes pulled to the basket below. Unfortunately, thats probably the only part of the process cleaning anything.The enclosure says its designed and assembled in U.S.A. and, unfortunately, speaks to our manufacturing ability. Some of the engineers Ive worked with over the years suggested areas to inspect. I was able to use my phone camera to look under the unit and noted that it is controlled by a main drive motor and a little synchronous motor with a linkage that Im guessing changes agitation direction. Both are made in China. Ive considered repairing it and just pulled the wash plate for inspection and found nothing beyond the difficulty of pulling the wash plate. Probably an issue with the drive assembly and a few hundred dollars in parts to fix. Ive also had input from someone about the cost of replacing the control board. I grew up with TV commercials of the Maytag repairman with nothing to repair in the world of reliable, American products. Its disappointing to find that is no longer the case. The low tech GE washers weve used all our lives were old and ugly when they left our house. Not defective, a few drops of oil below or worn finish but still working. It really is a disappointment to look at where we are today. It didnt have to collect samples on Mars or deliver orders in a self-driving vehicle. A reliable washer to clean dirty clothes is all we hoped for.

Maytag washer, model# mvwp575gw0, which is under warranty. This washer is less than one year old. Within the first couple months the transmission leaked oil and service tech had to replace the transmission. A few months later – another problem, clothes wet after spin cycle - tech told me the agitator base and/or couple parts need replaced. Quality control appears to have been lacking at the factory when this washer was made. This house has only one person presently. The washer was not abused.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

Purchased 6 11 21 from Menards. $1100.00. With extended warranty $134.99. Lid lock inoperative on 9 11 21. Called Menards, past 30 days. They will not help. Called Maytag, took 2 weeks to get a diagnosis on issue, while technician was there week of 28th the motherboard fired. Another month, part came in October 23rd then wiring harness fired, and pump also. 1 week for parts, which were replaced, Technician came and was stumped as it still doesnt work. Diagnosis after this appointment for the pump replacement is clutch, rotor & stator are fried.Nov 18th, new rotor came in and Technician says although brand new in box, it is defective from factory. New one ordered. In meantime I have called maytag every week with no results, they tried to get me to accept 100.00 gift card, I laughed, as we are a family of 6 and generally have 6-8 loads a week. And have spent on average 70.00 a week for the last 14 weeks, we could have bought another washer by now. Last maytag lasted 16 years! This one 3 months...They finally decided to replace it, but we wont recieved it for another 4-5 weeks. So, 20 - 22 weeks of no brand new washer bought in good faith, brand rep, and paid for based on prior experience. So far, No customer service, No brand reputation, No product longevity. I will never buy another maytag, ever. If you only had negative stars to award this useless product. This is almost criminal, and is close to being fraudulent and willfully deceitful. It is false advertising and to date they have not really stood behind their product...

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

I purchased a washer and dryer model MAH8700AWW. In 2005, I purchased the extended warranty. In 2009, I had to replace the main control board and motor on the dryer. Now, I find out that the washer has a warped drum which caught on the door boot and messed the shaft up. I didnt know that it has probably been that way since I purchased it because every time I washed clothed, I had to stay in with it because when it would go to spin, the washer would walk out into the middle of the room. I called about it and they told me to put rubber pieces to hold it still. Now it is going to cost $ 821.95 to fix. That is more than I paid for the washing machine and Maytag will not help to fix it. I would like someone to contact the company and find out why they dont stand behind their products anymore.

I need a new circuit board for a $2500 refrigerator. It was Saturday night of a holiday weekend when the ice chute started opening and closing and lights on door panel flashed like crazy. I called Maytag, who set up a service appointment for me for Monday. The tech came at 6pm and said there was nothing he could do without a part from Maytag and left. I proceeded to throw out all spoiled food and load a cooler with ice. I called Maytag, and they said it will take about a week to receive the part and have service. I have children in the house, and we live in Miami. I said that I would pay for overnight delivery of the part, and they told me it couldnt be done. I called this morning for a tracking number of the part, and they told me that it wasnt sent out as of yet. According to the internet search, this is a problem with a considerable amount of model number MF12568AES, and I should have been notified by the company. They claim it is a special project, not a recall.

I will never buy another energy efficient washer again. My Bravos is supposed to save money and be environment friendly, but when you have to wash clothes more than once to get them clean, theres no savings. Ive tried different detergents, cleaned the washer, rinsed twice, added vinegar, baking soda and everything imaginable to get the clothes smelling fresh without any luck. I have had several items ruined because the bleach dispenser pours onto dry laundry. Im disgusted.

We purchased our double free standing gas range about 6 years ago. Our top oven went out about 4 years after purchase. We purchased the extended warranty from Sears and it was fixed at no charge. About a year later, the top oven would not work again. We called Sears, our warranty was up so it would be a repair that we would have to pay for. We decided to go with the Maytag repair service since it is a Maytag appliance and we had to pay anyway. The repairman came in and said that the top box that holds the electronic in it had fried wires and it would have to be replaced. So for $480, he could replace it. It was more than likely caused by a power surge. I just read that this also coincidentally happened to someone else so I find this cause to ask more questions. I also note that the top of the oven behind the burners where there is some sort of vent gets extremely hot (I accidentally touched it and had a blister the next day) when the oven is being operated. This is directly under the box that holds the electronic components. I would think that may have something to do with the wires frying since it is that hot directly below the panel. Could this be a defect in the building of the stove? Has anyone else had this instance beside the one person that I read about on your website?

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

My clothes sometimes come with white spots on them. My clothes are very twisted. I would LOVE to have Maytag replace my washing machine so I could again sing their praises!!!

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

Clothes do not turn over in the wash cycle. The clothes at the bottom get plenty of hard scrubbing from the agitator but the ones at the top barely get wet and never move down to the bottom. Insufficient amount of water enters the tub. The repairman says the washer is working as designed. Neither Maytag or Lowes will take back the washer. Worst appliance Ive ever owned. Bummer!

Maytag Model #MBR2258XES refrigerator purchased May 2014 from Home Depot. Problem #1: Freezing in refrigerator compartment (frozen vegetables). Problem #2: Water leakage on floor from defrost. Wood floor is/has expanded and may now be ruined. This model is now discontinued. Looking into contacting an attorney.

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

Bought a new Maytag Over the stove model Microwave from Lowes. It worked fine for a while. Then it started saying open close door. We opened the door and closed it, and sometimes it would work. This went on for a while till it finally would not work at all. Called for repair, the service guy came and took it apart and one of the door switches needed adjusting. He left and it was working, good deal. 2 days later open close door started all over again. We found if we lifted the door when closing it, then it would work sometimes, until one day it would no longer work. We called for another appointment, and got a new company to fix it called ABCO. The service guy showed up and tightened a screw and it worked again, said the other service guy might have forgot to tighten it down. I tried it and it worked. We did not touch it again till next morning and back to open close door again. Called ABCO back and got a new service time for Wednesday next week. Wednesday came and went, called to see why no show. They said we were not on the service list and were very sorry. So we set up a new time for them to show the following week Tuesday between 12 and 3 pm. At 3:49 they called and said sorry, but they were not going to be able to make it today. I told her then get us tomorrow and was told they were very busy and maybe Thursday would be better. I told her we were in line and and should get service before others that came on later. Her reply was maybe Monday of next week was better. After the runaround she said they would try for Wednesday tomorrow, but no promise made. After that I called Maytag direct and they said nothing they could do except make another service appointment. She told me I could get a service appointment tomorrow Wednesday between 8 and 12am or 12 and 3pm. I asked with who this time and was told ABCO who just told me they were too busy to show up tomorrow and had put me on standby. In the meantime I paid over $300 for the Maytag microwave that is never going to need service because the Maytag service man is so lonely. And bought a $ 200 Panasonic counter model so we could have a working microwave. So now we are in over $500 and still no Maytag working microwave. They did send me a letter offering me a discount on extended service plan if I want one. I told them it would be cheaper after the one year runs out under warranty, to just junk the microwave because it has cost me way more in wasted time, waiting for the lonely Maytag repairman to show up. Bottom line do not buy a Maytag Microwave model MMV4205DS-1 unless you just want a good looking decoration over your stove with a nice light, and have plenty of time waiting for the lonely Maytag repairman.

We bought a Maytag oven in Late October 2018. On January 22, 2019 the oven quit heating. Since it was still under warranty we called Maytag and they sent out a contracted service technician. The service tech said the circuit board had gone bad, and said it would be 5 to 10 days for part to come in. After a month the part still had not come and service tech was not returning calls. We called Maytag after another week and they provided very little help other than, We will contact service tech. Service tech never called us nor did Maytag call back. Called Maytag back on 3.10.2019 and asked how we could get this part and oven fixed. Customer service representative was not very helpful as they asked for part number which she was told was a circuit board and the tech they sent did not give that to us. After the customer service rep continued to provide any help other than say call service tech they sent out. I asked what if they replaced it for us since we have been without now for almost as long as we have owned. She stated Maytag does not do this except in extreme cases. I asked what is considered extreme cases. She stated she did not know. At this point I asked if she could transfer me to her supervisor and sat on hold for an hour, then had to leave for work. Very disappointed with Maytag and their lack of support to back their product.

Weve had this washer for five months now and really regret buying it. It cannot remove even minor stains and often leaves residue on clothes, even with extra rinsing. I spilled coffee on some fleece pajamas and it took four washings to get the smell out.

Maytag in general has gone from being reputable in the early 70s to being the epitome of a rip-off company that sells junk, then refuses to stand behind it. I have a Maytag Washer and dryer. The washer continually goes out of balance and spins across the floor. Repair people tell us that our floor is not strong enough - funny, our new Samsung washer has no apparent issues with the floor or anything else. Our Maytag Gemini is a piece of crap. The ovens do not work or heat up most days. Maytag pushes replacing an EOC board at $800.00, but then the part is not available. Stove is not even six years old. Maytag is a synonym for junk.

This washer is awful. We had repair guy out within year one 3 times. Changed the door gasket because it was a known problem. That did not fix problems. We have to drain and clean out hard to reach filter monthly, socks get caught in drain filter constantly. Horrible, horrible, horrible. Hate it.

I purchased a Maytag dishwasher May 2019 Model# MDB4949SDE3 Serial# F80446835. It has to be one of the worst purchases I have made in a long time. In fact, I wish I could return it and start over with another brand. My glasses come out of the cycle with film and silverware is spotted. I have tried everything from scrubbing and rinsing before I put into the dishwasher, every product on the market, making sure my hot water heater is on high to settings for the longest most powerful cycle and it still continues to disappoint. My warning is DO NOT buy this dishwasher.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

I purchased Maytag dishwasher (model # MDBH979AWW3) in June of 2010. Trouble started on washer after 18 months. Touch pad buttons dont all seem to be working. Occasionally gets to run after slamming door multiple times, but dispenser doesnt function properly. After trying to diagnose myself with door switches, connectors, etc., I caved in and called service. Service quoted $470 parts and labor to fix the problems, including control touch panel, dispenser, and control board (seems common from what I read here). Wish I had seen this string of posts before I called Maytag/Whirlpool customer service to see if they would help before I did any repairs. The responses I got from the service rep were rigid and scripted. Only time she varied from the script was to explain that modern high-efficiency appliances dont tend to last as long as ones 20 years ago. 18 months? Really? I might buy that if it was a mechanical durability design issue. Supervisors responses were also scripted, pointing back to the 12-month warranty. She said she did a warranty search on my model and that there was no warranty concern for this problem (really?). If there was, she might be able to help me. I guess there is no warranty history because most failures are between 12-24 months and the consumer has to pay for replacement outside of warranty. No semblance of customer service or customer care, just repeating what is on their website. Response was: I am sorry you are dissatisfied with the product and my response, but there is nothing I am authorized do. Sent an email to Maytag customer service regarding the problem and customer service interaction. They called back saying they stand by the original customer reps response, but offered to have someone else come out to give a second opinion on the problem. From what I read here, that doesnt seem necessary. Wish Maytag/Whirlpool would at least acknowledge that there is a problem, even the auto industry seems to have figured out a way to equip the service industry with known recurring problem history (TSB) and offer token help to keep customer loyalty. Apparently another quality organization fallen victim to short-sighted methods of maintaining shareholder value.

I bought the Maytag washer and it lasted 5 1/2 months. I am now going on 1 month without the washer because no one wants to take responsibility for it. Your warranty and service is crap. I will never buy another Maytag product and I will be sure and let anyone that I know that is about to purchase one not to!

I’m 41 years old and finally had my first new washing machine. Four days later, while my 11 year old had the stomach flu, it died. Not impressed. Apparently the delivery guys left a note on our file saying there was a defect on our washer and that we needed to contact Maytag. This was news to us when we called The Brick today. I hope they didn’t knowingly sell us a defective washer. Alas, we have to wait until Monday with pukey sheets in the washer.

Maytag WFW7590FW & YWED75HEFW 24 Compact Washer and Dryer: These 2 machines are a lemon and the extended warranty plan was completely disappointed. Both needs maintenance before the 1 year warranty ends. The washer was the worst between the pair. The washer cannot spin the laundry dry. The Home Depot extended warranty plan was not the cost. It takes 2 business day for the service call to call us back. Then a schedule date was 2 days later. The service person complained about not getting authorization to do the work without charging us. He did even showed up for the 3rd call. He did nothing to resolve the issue and said the diagnostics showed there was a load issue, which was not true. A very light load still didnt spin dry. The washer not spinning clothing dry issue has been more than 1 month and is still not resolved. The repair person Dean didnt even re-schedule another date after not showing up today. There is a 90 day policy that we cant request for another repair person to attend to the issue. The dryer also made excessive noise which was caused by a broken attachment that established the drum.

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

I purchased a Maytag stainless steel French door model the middle of 2006. While cleaning the French doors with the cleaning product given to me with the purchase of the new fridge, I notice what looked like coffee on the doors. It wasnt, it was rust on the stainless steel doors. I called the service tech and they came out. Rubbing the fridge, he told me it wasnt rust. He took a closer look and found that it was in fact rust. He called his office; they told him that rusting on the doors has been an issue lately. He charged me $65.00 for what I already knew. I called Maytag and it took a while, but they decided to send new doors. However, I had to have a Maytag rep install it, which would cost me. I didnt have it done. Two years later in 2010, the French doors felt hot to the touch and the inside was warm and not cooling. The freezer was fine. I called for a tech to come out and it’s another $65.00 to fix a fan motor that blows cool air from the bottom to the top. Oh, it’s not under warranty because it wasnt inside with the motor. Total cost: $235.00. In 2010, I woke up and opened the fridge to get milk out. It was warm and so was the inside of the fridge. I thought it was the same problem, but the freezer also was warm. Upset and not wanting to pay for this again, I unplugged the thing and started using a little fridge that I have stored in the basement. It has no freezer. Today, I finally got over being pissed and decided that I would have a tech come out and find out and finally fix it. The tech said that the compressor has failed and it would cost $790.00 to fix. Im not having it fixed, so it’s another $65.00 gone. The tech said that the compressor in Maytags/Whirlpools has been a pretty big issue lately. All I can say is that I will not ever purchase Whirlpool products again. From inside to the outside, this product has been unsatisfactory. I just noticed that the rubber is failing on one of the French doors. Wake up, Whirlpool. Model number is MFD2561HES.

So our 4 year old Maytag Dishwasher just took a crap. Thank God we were at the kitchen table when it started to smoke, which smelt like burning wires and unplugged it immediately. Repairman came out and said it would be a 3 to 4 hundred dollar repair. What happened to the great 10 year Warranty? Oh yeah, its a limited warranty which does not include wiring. Could have burnt down my 4 year old home, but thats ok, not covered. The good news, the upper arm I replaced due to wear and tear would have been a free repair, because it would have been covered! No more Maytags in this home, ever!!

I wished I researched more before I purchased, but like most people, I believed in the reputation of Maytag. Like many others - my control panel started to go out 19 months after install: Had my first event with the washer; it would not allow me to select normal wash. A high-end machine shouldnt have electrical connection problems within 19 months, just 7 months after the warranty expires.When the repairman pulled apart our machine, he found a similarly burned looking touchpad ribbon cable, that was burned in exactly the same position as the photos shown on Maytags website under the review referred to. Maytag/Whirlpool has set up a special phone number to deal with this problem: I dialed 1-866-931-7384... Been on hold for over an hour Of course - NO answer! Ill try later but I am very angry that this has been a known issue BEFORE I purchased mine at Home Depot. What a piece of junk. This is the last Maytag Ill ever buy again. The service is horrible, the product is junk.

New side by side, water inlet to ice always freezes. Had a service man out, said some tube needed to be enlarged but still freezes up.The ice dispenser is total junk. Keeps spitting out ice after glass is removed and just a poor design. Dont recommend this brand.

Maytag washer not draining properly. Called Aug 15 for help. First tech in on August 23, makes a diagnosis, orders part; no news, I call, am given Sep 15 as next date. Come 9/15, I take off from work, only to find out tech cannot come that day, to reschedule. Next tech comes 9/25 with a different diagnosis and different part to order. By October 3, an announcement that part came in, to make an appointment. By now, its been a month and a half, I am so angry. I call a friend, who fixes it in 15 minutes by simply clearing a clogged drain filter. This is unacceptable: the inordinate wait, incompetent techs, unresponsiveness from customer service. I cancelled my contract with Maytag Warranty/AIG.

Ive had this Maytag for more than 15 years and it still works well. Its a basic fridge, no special features. Just keeps food cold or frozen. Freezer at top, fruit & veggie bins at bottom, cheese bin. No problems, good performance.

After two years of dealing with this awful washer, I felt compelled to write a review. I have had $50 rebuilt washing machines, as well as new ones from the bargain aisle. They worked very well for us. But when it was time to purchase a new one, we wanted a washer with a larger capacity and ended up with this boobie prize. Honestly, whoever designed this washing machine should be ashamed. I cannot believe it made it past the testing stage! Blankets and quilts roll into a ball and never get clean, detergent gets trapped inside this ball of doom, the simplest dirt on clothes survive the cycles, and forget trying to clean stains. I scrub them out, then use the rinse cycle. JUST AWFUL!!! Honestly, this is THE WORST and most disappointing purchase I have ever made. Stay away from it.

We purchased a gas range and over the range Maytag microwave a few years back and have had problem after problem with the microwave. Weve had 3-4, maybe more, repairman here and they replaced pretty much everything. Its been going for about a couple years now without a service call, but it went out again today. Very frustrating when you spend good money on junk. We are now to the point that we either replace it with another brand or we just put in a hood and have a microwave on the counter. Just so frustrating. I would not recommend Maytag over the range microwave to anyone!

We purchased a Maytag Bravos Automatic Washer 6/28/09. The interior enamel around the bleach dispenser started rusting about six months ago and it’s getting worse. Our white clothes are getting rust stains on them. Otherwise the machine works well, but what a huge flaw. We will buy a new machine, but not a Maytag.

Very easy to use- just dial the button to the load of your choice! The only problem I have is it becomes unbalanced sometimes on a heavy load. :( And it is also energy efficient and lets you know when it needs cleaning.

My husband purchased the Maytag Bravo December 2013. We immediately started noticing clothes been destroyed and stains still in clothes. We immediately contacted Whirlpool and shared our concerns and they sent out technician. He stated that the motherboard was gone. After repairing the motherboard, that do not stop our clothes from being destroyed and making them clean. I have wrote numerous letter to the CEO of whirlpool and sent pictures. When they decide to call you back months have passed and still they do not want to help you. Whirlpool have refused to take responsibility for a bad product they invented. They do not stand by their mission. Someone please help the consumer, because this big corporation refuse.

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

We purchased a Maytag refrigerator model # 1TXEGMYWOO. The refrigerator part froze all of the food in it. We moved the temperature selector to the last place (two notches away from the recommended setting), and the food still froze. The furniture store we purchased it from replaced it with another refrigerator (same model). And that one did the exact same thing. We had to throw out more groceries. Obviously, this model is defective. We are now waiting for the store to replace this one (with a different model and brand). They have been very good about trying to make things right for us. Maytag, however, is a different story. They were very rude and indifferent when I called to complain. Their policy is to repair or replace the part (temperature gauge). I dont want a new part. This is a new product. And I bought it expecting it to work. I have had to throw hundreds of dollars worth of groceries away. I was very disappointed in their attitude. I will not purchase another Maytag item again. They used to have a good reputation. They now sell inferior products and do not stand behind their products.

We purchased the washing machine (MVWB400VQO) on July 9, 2009. Now we must buy a new washing machine as this one is apparently beyond repair, or else the repair costs will far exceed what it would cost to purchase a new machine. We are completely disgusted with its failure, as we paid $822.36, with the delivery fee and the tax. We expected that this machine would last for years, but here we are, 42 months later, having to again invest in a washer. Now that we have a computer and are able to browse your performance reports, we wish we had been able to read them before, in which case we never ever would have bought it at all.Yesterday it spewed water all over our basement, flooding things that should not get wet, providing an atmosphere for encouragement of mold and rust. The motor is gone as the housing is cracked, which was caused by debris getting into it, something that we could not have known or prevented. This is very poor design by your company, in our opinion. We called some repairmen, all useless as apparently the whole machine would have had to be completely dismantled at a rate of $84.00 per hour, and he could not tell us how many hours that would take, to say nothing of finding a new motor for the thing.We will never again buy a Maytag product as they are expensive with a too-short shelf life and there’s nobody who cares when you need help for something that should not have happened at all. I understand Maytag is really not the good old dependable Maytag we used to know and love at all, but rather is now owned by the Whirlpool Corporation, whose products we will never purchase either.I know why that lovable old Maytag repairman we used to see on TV is retired. Its because he could no longer stand the quality (or lack thereof) of the appliances that you are now producing. He is probably home, hiding his head somewhere and hoping nobody will recognize him. And what, kind sirs, do you have to say about this? Thank you in advance for your prompt reply.

Ive tried all manner of washing clothes, especially dark ones. Different cycles, different detergents and amounts, but it always leaves scum marks in folded places. I have to either brush off what I can, and/or rinse the clothing in a sink and then rewash the clothing without detergent. In an attempt to save water, I end up using two or three times the amount.

I have a Maytag Washer and Dryer that I am very happy with. I have had both of them for about 6 years. I had a problem with the soap dispenser not working properly shortly after I purchased them, but a service technician came and fixed that within a few day. I will probably stick with the same brand when/if I do have to replace them.

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

We have a model MF12269VEMS. Approx 3 years old. Ice maker and water dispenser work great. Fridge works well. We have experienced over the last 6 months a buildup of ice that forms inside the freezer under the drawers. If we dont catch it every 4-5 days we cannot open the drawers as the ice catches the bottom plastic drawers. I called Maytag directly and the pleasant young lady told me after checking that it did not seem to be an issue...clearly after looking into the internet I am not alone! Maybe someone can email me a fix?

The washer does not clean clothes. Thank goodness I bought a 4-year warranty because they have been out 4 or 5 times on washer alone. The dryer is now squealing and shuts off (a safety feature I am sure). The repair person replaced the pulley system and one belt, it still squeals and shuts off. I called the Maytag CEOs office and talked to a machine. Some really nice lady called me back and said she cannot do anything to help me. They have no consumer person to help you and troubleshoot with you. The washer is rusting, it is an inside washer. I live in SE, Texas and they told me it was due to living close to the coast. Well, Ive had GEs that never rusted and in fact, the problem is really with all the HE washers. I hate them. They do not clean clothes. I will never buy another Maytag or Whirlpool product again.

Bought a Maytag Stainless Steel kitchen stove to upgrade my appliance before retirement. 14 months later the spring loaded hinge failed. A bad piece of engineering in the way of a retainer pin to hold the spring pressure tore out of its pressed metal hole. The hollow pin was fastened in place by a 3 fluted punch instead of with a proper rivet with a head. My local parts supplier had 10 on hand so you know they are aware of this. $70 and an hours labor and it is repaired. My local seller said, Too bad you didnt get the extended warranty. So much for Maytag dependability.

We are on our 2nd Maytag refrigerator in 6 years and both units have failed. Maytag will not stand behind their product and the service company declined to come out to look at the unit because we were upset and contacting the BBB. So we have spent thousands on 2 refrigerator units that have lasted 2.5 to 3 years a piece. If I could give no stars I would and I would advise to look at other companies and models.

I purchased my Maytag gas range (model number mGR7665WB) on Thanksgiving 2011! It worked fine until May 2012. Then the bake function just stopped working. If I select bake, the temperature fails to rise above 100F and a sickening gas smell fills the kitchen! PC Richards, where I purchased the product from, sent a repairman who took two weeks and two visits to fix the part! Everything was working fine until six months later during cooking for a full house on the day of my daughters birthday party. Same problem, bake function failed again along with gas smell! I was pregnant at the time and very worried about the gas smell! We had to leave the house a few days after that due to the hurricane and when I returned, everything worked great for a few weeks only to fail on Christmas Eve leaving me to cook the meat for our Christmas Day dinner in a neighbors house, highly embarrassing and inconvenient! Now Maytag and PC Richards are only able to repair at a high cost to me which I cant afford and feel I shouldnt be responsible for as this product has been consistently unreliable and possibly dangerous. I am especially concerned about the gas smell as I have a newborn and a 3-year old in our small apartment!

I was all too excited to FINALLY own a new set! I conducted research and read reviews. We decided on the Maytag Bravo XL set (Lowes) and was thrilled! For the first 6 months. They were both fantastic! 6 months later, several times the clothes washed were soaking wet as if they had been set on soak. It continuously alerted to clean after 3 loads. The dryer... Well, evidently, if you live in a high-humidity region, DO NOT HOOK TO THE WATER LINE FOR THE STEAM OPTION. It will soak your dry clothes! After 3 loads of drying, it fails to re-start for the 4th load for at least 12 hours! When paying over $1,590 for a new set, this should not be an issue. Mind you, I do laundry once a week - 5 to 7 loads including linen. Fortunately, we paid an additional $200 for the warranty at Lowes.Lets see what happens there!

Purchased a Maytag MDB4949SHZ dishwasher new from Home Depot in January 2018 as part of an extensive home remodel and addition. Did not move back in permanently until late June 2019, so the unit was not used at all until then. It quit working in January 2021 and our local (Sandpoint, ID) appliance repairman diagnosed a bad motor and pump assembly (the main functional component of the dishwasher). The unit was marketed as having a 10 year warranty and based on past experience with older Maytag appliances we purchased it. The fine print reveals that the 10 year warranty applies only to components that are unlikely to ever wear out or fail; all the rest are covered by a one year warranty. Part cost is over $200 and does not include installation. Maytag customer service (45+ minute hold to speak to a live human) of no help. No way are we throwing good money after bad to fix it. Lesson learned; just purchased a Bosch.

Not only does the water not drain properly causing an insane amount of stench of moldy water being trapped, but this washer has had nothing but problems since we got it. Error code after error code, problem after problem. So disappointed. My husband wanted an LG and I said it had to be Maytag because Maytag was the best. Thanks for making me a liar Maytag!

Same complaint as most of the others: bought a refrigerator in 2013 and about one month after the 1 year warranty had run out the freezer started leaking water all over the floor and build up is on the bottom of the freezer, making it difficult to pull out the metal drawer. :( We do not have the water even hooked up to the automatic icemaker so have no clue where the water is coming from. Clothes washer has never worked properly from day one, didnt fill up with enough water. Had the repair man here while the warranty was still in effect and he verified that the washer DID not fill with enough water therefore leaving soap and grime on our clothes. :( He had to order an entire new brain and replaced it. Worked for a couple of months better than it ever DID and now back to soapy, grimy, dirty clothes again. Why isnt there a recall on the part that keeps backing up on these bottom freezer Maytag refrigerators? Someone needs to start a class action lawsuit and get these things recalled and replaced. Spent a lot of money on this brand new refrigerator and was so jazzed to get a brand new one for the first time in my life. :( Well that was surly short-lived. Shame on you Maytag, your company has really gone downhill. I would love it if an attorney could start a class action lawsuit with Maytag on their bottom freezers.

I had a Maytag dishwasher (made by Whirlpool) that after 4 months of ordering wrong parts, parts arriving damaged, and parts that were re-engineered and did not match up, the dishwasher could not be fixed. The extended warranty people (AIG) promised me twice on a recorded telephone call that they would exchange my dishwasher, and after many many heated telephone conversations was given a 20 minute lecture on how the word exchange does not mean they will replace it. The frustration ultimately overtook my misspent loyalty in anything made by Whirlpool and I decided to accept the buyout of my extended warranty contract, at a loss of hundreds of dollars to me - well worth getting rid of that dishwasher and any further affiliation with Whirlpool corporation. Absolutely horrible customer service. Unbelievably god awful treatment. I dont know what happened to customer service at Whirlpool, but my dealing with them has convinced me that the term is an oxymoron at Whirlpool. Horrible horrible customer service. I have never been treated so poorly in my life. I truly dont know how they can still be in business if they treat their customers like they did me.

I purchased a Maytag Bravos HE top load washing machine from Sears in 2011. In January 2015, the machine stops at the spin cycle and wont continue the full process. The lid light comes on and blinks red. The machine made a loud grinding noise. A technician from Sears has been to my home 4 times in a month but unable to fix the problem. I have to take my clothes to the outside laundry. I have a protection warranty but it ends in a week. Im frustrated. Maytag Bravos sucks.

I bought a Maytag MDB8959SBS2 December 2013 with several major appliances for our new home while they were all deeply discounted and bundled with cabinets etc from Lowes. Moved in June 2014. Said dishwasher crapped out last month (May 2015). Buttons all fouled up, push normal and 6 other lights come on. Tried different resets, reboots, power down all no good. I ordered parts to repair, control board, control box, no luck. No warranty because purchase date was December 2013. This thing didnt last 11 months of use, and its just my wife and I running maybe 2 loads per week. I will certainly do more research and buy a foreign make/model or at least one not made by Maytag or affiliated brand. Unfortunately this supposed Made in the USA sticker sure doesnt stand for quality with this company.

Maytag mod# MBF2258XE81, Ser# K04712605. 3 years old. At 6 months old, the drain plug clogged. Freezing water under pull out drawer of freezer, spilling onto kitchen floor. Fixed under warranty. 9 months later the same thing. I had to pay $190. Now, it has been happening for 6 months, and I use a spatula to lift the sheet of ice out. I have to do this every 10 days, or it leaks onto the floor, tile and rug in my kitchen. This is just wrong. I see I am not the only one. If Maytag does not fix this known problem, I guess I will get a new fridge. I had my last fridge for 21 years, never had problem. Thought I was upgrading.

This dishwasher has an electronic control panel that is faulty. Within one year of purchase, the control panel shorted out. It was replaced under warranty. Almost exactly a year after that, the same part failed for the same reason. This time, Maytag refused to replace it for free since it was out of warranty. A new control panel would have cost over $250. Disappointed with this Maytag product and their refusal to replace an obviously defective part, I decided to buy a new dishwasher from another manufacturer. Also, it did not make sense to me to spend that kind of money to replace a part that would continue breaking every year. AVOID Maytag dishwashers with electronic control panels!

I purchased a new Maytag dishwasher model MDB7609AWB1 approximately 2yrs ago from Sears. We purchased quite a few new appliances from them and they are always helpful. Within the first year, right after the warranty was up, it stopped working. No lights on the power panel. I called Sears, out of warranty, sorry. Said they would give me a deal on the repair. Sears came out, replaced the computer. $230.00. 6 months later, it stops working again. I go on line to look up these models and sure enough a lot of people are having the same issues. I did some of the checks that they said to do and found my plastic door latch was broken. A little plastic arm that actuates the switches broke. Should have been made of metal. I replace it myself, very easy, by the way. So I figure, in another 8 months it will prob break again. They run anywhere from $19.00-$30.00. 2 days ago power panel and light, not working again. I called Sears and asked them if they were having issues with the power panels that this was the second time in less than 2 years, and if there were any recalls, they said no. I guess they dont follow their reviews, but according to google reviews, its a major problem with most of them. Maytag, Whirlpool, and Amanda. Ordered a new panel today, again they are $141 from Sears but if you shop, you can get a new one for less than $85.00. If you have any kind of mechanical skills, you can replace it in less than 20 mins. It just seems to me that this big companies have let their quality control go and are more concerned about the profit. There should be a recall on these. Do Not buy a Maytag/Whirlpool dishwasher, they are total junk. Sorry Maytag, you lost another customer.

The oven hasn’t caused any issues. It’s beautiful stainless steel and black finish creates a shiny but modest finish to my kitchen. It’s self cleaning power is also useful and saves time and where I come from time is money. It cooks food evenly just as an oven should.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

This machine is the worst! I purchased this Maytag washer 2 years ago and the machine leaks from the left side bottom. I called Maytag and they said I need one of the techs out to check the machine and the cost was going to be $115 so I agreed even though was not too happy that there is no guarantee after 2 years. The service tech arrived. He could not move the machine himself and was a little angry so my wife called a neighbor to give the tech a hand after looking at the machine. He called if office to help him diagnose the unit and said the drum seal was bad and it would cost $315.00 so my wife agreed but at the end of the transaction my wife asked the technician, Is it guaranteed that this would fix it? He replied there is no guarantee but we still have to pay to try... What kind of diagnostic is this, Im very unhappy with this company. 1st the machine sucks after 2 years to start leaking and 2nd their service dept. sucks also... stay away from Maytag.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

This is the worse washer... As many other have complained I have the same problems. This washer it will not fill with water ever. It doesn’t rinse clothes or clean them as I’m use to the old washers doing. From day one I noticed the water does not fill in the tub and wondered how can the clothes be getting cleaned properly. Getting a F51 code and after going on YouTube and checking for problems it seems to say the same code after it works for a bit. This is the worse appliance I have ever purchased. I am so frustrated and will never purchase a Maytag anything again. Never did in the past up to this one and never will after this one.

I have had nothing but headaches with our washer. We purchased it 4 years ago and after using it for a few months, I took it out because our clothes came out smelly and unclean. Called Maytag and they did nothing. So we went back to a regular washing machine and put this machine in the corner of the basement. I refused to throw away a $1,100.00 machine! So this year our machine quit, so we decided to try using the machine again to save us some money instead of buying another one... Well, that lasted for only a short time. Clothes still smell, came out unclean and just yesterday, the machine stopped rinsing and spinning! This machine has barely been used and its been nothing but trouble. Maytag service just plain sucks. They dont care about their consumers. I will never buy a Maytag again and I always let everyone I know to not buy this type of machine.

I purchased a Maytag dishwasher on Oct. 12, 2013. The control panel failed in July 2013 and had to be replaced. I was unable to program a wash cycle and the lights would move all around the front. After the first failure, I was told that the control panel would only be covered for 3 months - the original purchase date for the washer, NOT the date of the NEW control panel. I was then talked into an extended service plan. Now, four months later, the control panel has failed again and I am unable to program a normal wash. A repair man is not scheduled to come for another 9 days. As a single homeowner, this product is not used even on a daily basis. I will never purchase another Maytag washer. They do not back their product with appropriate repairs.

I have ALWAYS bought MAYTAG since the 1970s. But MAYTAG is no more. Whirlpool bought them out. I have an HE (first mistake)... HE... will go away just like low flow toilets did!!! You cannot wash clothes in 4 of water. I bought a top loading Brazos XL for $1100 (second mistake)... Have had it just over a year! I should have returned it but did not. Huge mistake (#3)... Repairman told me to get rid of it as fast as I can. Will eat me up in repairs. Now needs repair again for another NEW issue... The fill sensor does not tell the machine to load the proper amount of water. Now I cannot clean washer, tried three times last night. I am beyond upset. Repairman said buy GE! You can bet it will NOT be High Efficiency!!!!!

Hello, I bought the above top load Maytag washer last summer and shortly after purchase the spin cycle was accompanied by a load grinding noise. This became progressively worse per use and I contacted Maytag Canada. The experience calling is a challenge with often busy, and at times long waits. When I did get through on the line they were very good customer-service-wise and arranged for a local accredited company to attend my home and assess the problem. Service visit number one resulted in the lack of parts to fix, so I waited two weeks for the next visit with appropriate parts. Washer began to grind again, I called Maytag, another appointment was set, service call #2 again resulted in the SAME parts being replaced as service #1, and upon departure the washer immediately resumed grinding. Call #3 to Maytag and a 4th visit was scheduled to my home. This time with a different service provider, parts changed washer not fixed. Maytag called and this time I asked for replacement. Three weeks later I received a new washer. The version was updated so the drain hose no longer reached my drain pipe. Once sorted out, my first wash today with the new unit and GGGRRRIIINNDDDING.. I would not recommend this product. Will be calling Maytag again Monday.