Replaced a Maytag Bravos xl washer and dryer in 2015. First year was fine but almost right after the warranty period, the spinning cycle was loud. You cant even have a conversation near the washer. I put up with it after calling the repair department. Because I was told that it will cost as much to repair than buy a new washer. Now the washer does not drain when a small amount of cloth are in the washer. Dont buy this washer and dryer. Maytag is not as good as it once claim.

I purchased a Maytag dishwasher because they are supposed to be known to be a good brand. But my dishwasher is 3 years old and it started rusting around a steam vent on the outside of the door! This issue has been ongoing but as Ive been busy, I havent had the time to address the problem with Maytag since its out of warranty anyway. But I feel like this should not be a warranty issue to begin with, it should be a recall issue. I had a plumber look at this, and he said that it was caused because the vent was not properly sealed during manufacturing. Now it looks as though mold spores are growing inside the steam vent! Maytag will not stand behind their product, so why should I invest anymore money into it?! I would rather purchase another dishwasher (OTHER THAN THIS BRAND) than dump another penny into this garbage dishwasher!

I have had my washer and my dryer (model no. MGDB850WQ - serial no. MJ3311087), for 1 and 1/2 years. I have given both plenty of time and since the beginning, I have literally hated these products. This was a large purchase, so I feel locked into a terrible choice. I wish I had never bought these two items and will never use Maytag again. I will also never recommend these products to anyone. I do not like the new technology.

I have had commercial front loading washers since they came out (first was a Whirlpool Duet); although I like the capacity they have for large quilts and sleeping bags, they just dont seem to clean as well as the agitate-in-tub style, and they can take a ridiculous amount of time for a cycle -- wheres the energy savings there that they advertise? Im going to go back to the agitate-in-tub of water style when a replacement is needed. A lot of hype and expense, and plenty of experience with these on my part, but Im going to grade them a C, at best, compared to the agitator style washing machines I use to own.

Had a problem with the control circuit board on my 6 year old refrigerator. Had it serviced and found that the problem was common, the main circuit board needed to be replaced. The service person advised me it wasnt currently available from his supplier. I call Maytag and they said it was back ordered from their parts source. When asked for an availability date, I was told the date was unknown? I started a search for the circuit board and found it was indeed a problem for many many other consumers who owned this model refrigerator. Lesson learned: Maytag is no longer a good brand to own.

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

I bought this over the range Maytag microwave model MMV4205DH-1 5 months ago and today a hairline crack appeared alongside the door handle. I called Maytag to find out how I can get this repaired since, as time progresses, it will become worse due to using the handle to open and close the microwave. I was told this was a cosmetic warranty which expired after 30 days. They would fix it only if the microwave couldnt be opened. Apparently, the handle can become loose but as long as the door opens, they wont do anything.I bought Maytag because of their supposed reputation. Im so glad this happened with my $300 microwave as we were getting ready to replace our washer and dryer and were looking at Maytags. Good to know they dont back their products before I spend several thousand dollars on a washer and dryer. I will NEVER purchase another Maytag. My $120 generic microwave lasted 10 years and I gave it to my son and it is still going strong.

Maytag Dishwashers work great. It cleans well and appearance is very good. I have always trusted Maytag appliances. Its quiet running and also energy saver. If I had to replace I would stay with Maytag.

Bought a Maytag bravo xl washer and dryer two years ago. Spent around 1,500 dollars. Didnt make it a year before things started going bad on them. First the lid lock on the washer broke. I got the lid lock pulled out far enough that I could drill a hole in it and tie some thread to it to pull it out when the washer was ready to lock. Today the piece of junk just quit. Not long after the junk washer started messing up the dryer starts sounding like a fork in the garbage disposal. It still works and dries the close but you hate to even turn it on because of the noise. I will never purchase anything maytag again in my life. JUNK!

I purchased this set 7 years ago and the washer started stopping mid-cycle and the dryer sensor doesnt work. I called the Maytag service number and after several phone calls (they had my name spelled incorrectly and the wrong address), was able to schedule an authorized servicer. He said the motor and motor controller needed to be replaced and it would cost over $900. When I said I expected my $1,200 washer to last more than 7 years, the service person informed me that the machines were made by Samsung (not Maytag) and just carried the Maytag label. He said the Maytag Neptune washers and dryers were the reason Maytag went into bankruptcy and was bought out by Whirlpool. I am disappointed Whirlpool/Maytag does not stand behind this product and will not buy this brand again.

I bought a fridge, model number MBF1958, its a top fridge-bottom freezer. The freezer part leaked and spilled water that then froze onto the bottom of the freezer, which of course froze. I discovered this 1 month after the 1 year warranty ended. Maytag gave me a courtesy repair service guaranteed for 90 days. Of course, 2 weeks after the 90-day period ended, I have the same problem again.

My oven smelled for weeks after being installed. The first time I self cleaned, the oven stopped working and the door remained locked. It took weeks to get it repaired because we needed a part that had to be ordered. The second time we self cleaned, the oven smoked, set off smoke alarm that had to be disconnected, the control panel bulged, and the door locked. It was Sunday. I wrote a nasty email to Maytag. The service man who came Monday could not unlock the door, and said he had to order a part and would return the next Tuesday if the part arrived.Next, I had warranty issues. I had to get a copy of the purchase receipt from Home Depot to prove that the oven was still in warranty. Out of the blue, my phone rings on Thursday and it was Joe ** from Maytag in Michigan. He had read my email, said he was sorry for all the problems, and if I did not mind waiting 2 to 3 weeks, he would send me a brand new oven, would have it installed, and would have the old oven sent back for inspection. I did not mind (although there is only so many things that can be grilled or you can bake in a toaster oven). Three weeks later, I have my newly-installed new oven with its new, year-long warranty. Thank you Mr. ** and Maytag for the great service.

Wow, my dream oven, or now nightmare! I purchased a Maytag dbl oven MGR6775BDS in 2007. The top oven stopped working first after about 3 years and this week, the bottom. I cooked a meal on Monday and Wednesday. Without notice, it would not go past pre-heat. I have called several people and they all act as if this was a truly unique situation. Since I have been out of work, both my regular and extended warranty have expired. I had good faith in a product that carried the name Maytag and the fact that it was on sale for $1,200. I didnt know I had so much company. Yeah, I was told I could purchase a repair warranty for the sale price of $340. Oh yeah, I replaced a 20+ year old oven for the new and stainless dbl oven of my dreams.

MDB7749SBW - Purchased a new dishwasher from Home Depot & had them install it. It worked for 6 1/2 months & the control panel blinked & went dead. I did some research & found there were a lot of problems with the control panels & even a class action lawsuit. I went to Home Depot & they said contact Maytag & brushed me off. I set up a repair per warranty & all was fine for 10 months & same problem has happened again. I told them at Home Depot to replace the unit since nearly every repair job on the control panels prematurely fail again every time. I am going back to the Home Depot again. I do have older Maytag appliances that perform as required & I do know Lowes would have replaced the defective dishwasher.

In October of 2011, I purchased a $1,199 Maytag Bravos Washing Machine. It recently started making a really loud noise during the spin cycle (REALLY loud). I had a local appliance repair guy come and he told me the main tub bearings are bad, sealer is defective and that it would not be cost effective to fix it.I called Maytag and they offered to sell me another one for $839. I am very dissatisfied that I only got 4 years out of a $1,199 machine!!! Ridiculous!! I wouldnt mind a minor repair that cost a few hundred to fix... I get that. But for it to be junk in 4 years... I have a hard time with that for the price. My appliance guy said it was junk when I bought it. Year ago, you got 15 to 20 years out of a good washing machine. Now... I buy a high end machine and it lasts 4 years. And why would I spend another $839 for the same piece of junk!!! That would be throwing good money after bad. It is not going to happen. I promised Maytag that I would post as many reviews about their product as possible... so everyone can know that they make a lousy, defective product and charge a very high price for something that will not last. Dont buy it!!

I have bought a new Home Depot Maytag Impeller HE washer. After 6 repeat washings of 2 items that are lightweight dark brown it was obvious after drying they had soap and lint and lot hairs on it. I reached with no he detergent. The last 4 times the water level filled to 1 depth even for high level water setting to extra rinse or power wash settings. I went to Home Depot and they suggested I call Maytag repair center on Tuesday after the labor day holiday to have them check it out. I will also call the supervisor at Home Depot as I do not feel paying $600 for a faulty machine is acceptable.

I purchased the gas stove in June of 2012 from Home Depot, along with a Maytag microwave (Model MGR7662WB4). Home Depot installed both items. After trying to reach into the microwave about the stove, the knob would turn itself on with me brushing up against it. This happened several times, and one time the flame shot up and I almost got burned. The last time it happened, I did not realize that the knob was turned very slightly and gas was coming out of the burner for several hours. If it were not for a friend stopping over, I would not have considered the odor being from the stove. I assumed that the drains were probably backed up and started to add cleaners to the toilet bowls. I had to open the windows for several hours to get the smell out. So I called customer service 2 times. The first person said I would have to pay for the call if the problem was not Maytag and I said, “Forget it.” Then I went into Home Depot and the salesperson in there gave me another number to call for service. They came last Friday and said that he had seen at least 10-15 calls about this and since the unit was working as designed and no recalls, there was nothing they could do. “Just wait and see if a recall would be put into place and I would be on the list to fix it. In the meantime just keep the knobs off (which I was doing already out of fear).” My sister just bought a Whirlpool gas range this summer as well and asked if I could try her knob and it worked perfectly. Again I called CS and was told they could not send me those at no charge and that it would cancel out the warranty. So I asked her what I have to do before I or someone else gets injured and she said that until there was a recall, there was nothing they could do. I told her I was going to contact Consumer Report as well as Pam Zekman on Channel 2 news in Chicago. End of story; I still have the problem and no knobs on the new stove. Anything you can do to help please contact me, and thank you in advance.

Dishwasher is just 2 years old. Touch panel is bad, not Maytag of old. Waiting for the corporate apology. Seems to me that this is a common problem and a case of poor engineering. Also seems like a case of the middle American getting worked over by the big corporate giant. Not happy. Will not suggest Maytag to anyone. Not looking forward to having to replace something that should have lasted significantly longer.

To anyone out there who is considering purchasing a Maytag washer. My husband & I purchased a Maytag Bravo top loader washer from Sears Hardware here in Columbus, OH. We had always received great review regarding Maytag products. This washer is expensive & does not work. We started having problems from the day we purchased & had Sears come out three times for repairs. This washer has a built in scale which is extremely sensitive. We are very disappointed in this washer. It takes an entire day to do 3 loads of laundry. The washer goes off balance on every load. It doesnt do a god job cleaning the laundry. I do not suggest the Bravos series to anyone consider purchasing this product. It is a piece of JUNK! We purchased in Aug 2010 and the washer will need to be replaced within the next several months. Keep in mind that more expensive & lots of fancy extras doesnt mean a better quality washer or dryer. Stay away from Maytag or you will have the Old Maytag repair guy @ your door frequently.

I purchased a Maytag dish washer (not even 2 years old yet). I bought it on 8/29/10 and I paid over $400.00 for it brand new. The model number is MDBH949AWW1 and the serial number is F03422327. I am only asking for the part (motherboard). I have lots of friends and associates at church, work and social that I have talked to about this Maytag. And I would like to give a good report about the company and what they make and that they stand behind their workmanship. I know for a fact that they have 22 motherboards on hand ready to go out and what I have read online is that many people are having the same problem. I need a motherboard. I believe this unit should easily last over 10 years, so I am not asking for much. I will have it installed myself. I just need the part. I trust that you are a reputable company that has been around for many years and Whirlpool has taken new ownership and they have been around for a long time, too! My own parents owned one for over 30 years. This is all that I would request. I’m thanking you in advance.

I purchased a new gas range in Nov 2013, but didnt use it until April because I was remodeling a house I had just bought. When I used it to cook Easter dinner, my meal was cold; the oven heats, then shuts off. Maytag has sent service techs 3 times. They have replaced the control board and the DSI module and ordered another part, for which we have been waiting over 3 weeks. Now they tell me it will be here next week. Maytag obviously cannot fix the NEW range, but they refuse to replace it. They deem it to be repairable though they cannot repair it. Customer service claims to be sympathetic, but will do nothing except schedule another service call and offer to extend my service warranty. What good is a service warranty if they cant repair the appliance? If youre smart, youll steer clear of Maytag and Whirlpool appliances. They are total CRAP.

My Husband bought a Maytag Bravos Washer 2 years ago this next month. The washer is extremely hard on clothes. We have to wash all clothes on hand wash to keep them from tearing up our clothes, and we are having to replace the door lock for the third time. Of course the last 2 times were not under warranty. So once again, I cant do laundry when I need to. Thanks.

My husband and I purchased a Maytag Bravos washer and matching dryer in November of 2009. At three or four months old, the dryer quit drying and was emitting a weird smell and smoky air coming out of it. It was under warranty so a technician was called. A fan blade inside it had broken. The repairman replaced it and the motor as a precaution. There was absolutely nothing inside it that could have broken the fan blade and I always check pockets. My hoses were clear also. He told me that it looked poorly designed inside for air flow. He made a box out of sheet metal to fit inside it that he said would help it with air flow on the inside. I still have the dryer but I dont like it very much because it still doesnt do a great job of drying. It has to run too long and at too high a heat to dry laundry. The latch on the door broke a few months ago and had to be replaced too. I havent had problems with the washer as of yet. I like the washer and it washes very well but I will not buy a Maytag washer or dryer again. WHIRLPOOL OWNS MAYTAG NOW AND THEIR PRODUCTS ARE ACTUALLY MADE BY WHIRLPOOL SO I WOULDNT TURN TO THEM.

We purchased a Maytag Bravos washer & dryer in September 2012 and 2 1/2 years later March 2015, no heat. We called a repairman and he said heat element went out. When researching this problem online I was shocked how many people had the same problem as we have. It cost over $300 to fix and I am concerned that it will just break again and again after reading these reviews. I think that a class action lawsuit may be needed so that this unfortunate situation does not continue to happen to other consumers.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

The washer buzzes. Period. I called Lowes...they said to unplug it then plug it back in so it will reset the computer. I did twice...Nothing. A light comes on for the sensor...Then nothing. I didnt see all the bad reviews for this machine. I had my other Maytag for 24 years and the tub was going bad. This scares me. I will be calling Lowes later. They are selling defective machines and they know it.

The washer does not wash good on the initial wash. I have to wash my clothing twice. Cost and time consuming. The washer is “HE” and the water level is never enough. My clothes be saturated with dirt/lint scum and I never overload my washer. HELP!!!

I purchased a Maytag Bravos washer and dryer combo 2.5 years ago. Six months in, I noticed that the washer would always stop halfway through the cycle. We had a repairman come out because it was under warranty and he said it just had to be reset. I then started to become weary of the product. The washer, that is larger than most, is still a problem today. The dryer, the last couple of months, has not dried clothes completely. Today the dryer just stopped. Maytag will rip you off when called for service because the warranty is expired. I have owned old dryers for several years and I am so disappointed with the Maytag product that I will make sure that anyone I know thinking about purchasing a Maytag will buy another brand. The worst washer and dryer I have ever owned.

Bought top of line Maytag dryer and washer in 2011. Immediately had problems with dryer. Dryer resets timer itself to outrageous times. Clothes so dry they could have been parchment. This has continued with multiple service calls and electronics replaced. Still continuing but they will not act lemon law. I have extended warranties but get runaround everyone including Sears where I bought it pointing to each other. Tech came out today and said problem was the way the dryer is. No way to change it. I guess that is nature of the beast. I will never buy Maytag or from Sears again.

My old washing machine was about 25 years old but still doing a fantastic job getting the laundry done. When the dryer died we decided to replace both machines so theyd match. I had been setting money aside for years in preparation for this purchase. Ive only had them for two weeks and I stay awake at night wondering what GENIUS decided you can get clothes cleaner in a tablespoon of water than you can in an adequate amount of water?! My old washer could wash a load of laundry in about 20 minutes. Again, what GENIUS decided taking over an hour to wash a load of laundry in a tablespoon of water was a better way?! What working woman would choose to double the time needed to do laundry and then not feel confident that the clothes are clean?!!! I am so mad and frustrated and disappointed and I dont know what to do. I wish I could yell at somebody!!!

I bought a Maytag dishwasher, model # MDB7749AWW1, in April 2011 and the control panel just stopped working. Of course, Im outside the one-year warranty, but judging from the other reviews on this site, that doesnt really matter. A $500 dishwasher should last more than 17 months! I agree with the other consumers. The control panel on these dishwashers should be recalled. Obviously, its defective. Instead, Im being told I can either pay $250 for the repair plus a one-year warranty or $130 plus parts to cover a onetime fix. Ridiculous.

Maytag Performa Side by Side fridge PSD262LHEB door handle pulled off for the second time since purchase but this time, the handle knocked over a pot of hot water on me. I am just relieved that I have no small children anymore. I would consider this very dangerous in any household. The first time, it was covered under warranty along with the broken ice maker. The repairman stated that he had replaced many handles and due to design flaw, they would not last long.

My daughter purchased this washer and matching dryer as a set from Lowes about 4 years ago. It was one of the few with an agitator and that is what she wanted. After using the washer for the first time she was very disappointed to find that the shortest cycle took over an hour and that the locking lid feature couldnt be bypassed. A few weeks ago the washer began gushing water onto the floor which flooded the basement below. She had purchased an extended warranty which was due to expire the following week.She called Lowes and scheduled a repairman. He finally came 2 weeks later and used the Internet to help him diagnose the problem!!! We could have done that. He decided that the control panel was only allowing the agitator to turn in one direction during the wash cycle. So essentially it was spinning a tub full of clothes and water causing lots of water to overflow the tub onto the floor. Needless-to-say he had to order a part and cant return for over 2 weeks to install it. IF this is even the problem! He also said he couldnt disable the locking lid feature! If my daughter had been able to open the lid when the problem started she would have known more about it.We are thankful her machine was under warranty but she will have been without a machine for almost 2 months when and if it is fixed. This is completely unsatisfactory for a gently used 4 year old washer. The dryer takes forever to dry also. If you are buying Maytag based on how long your grandmothers machine lasted, you will be disappointed! This washer caused so much damage we had to file a homeowners insurance claim!

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

We have the 4000 series front loader washer. Within 8 months of owning it, it would shut off in mid cycle. You have to unplug it to restart it. Then, when it completes the cycle, it is still soaking wet. So, you have to put it through the drain and spin cycle again. There is something major wrong with the spin cycle. It takes about 2 hours to do one load of laundry and you have to stay home to do all of the steps. It costs as much to fix it as the machine costs. It’s the worst washer we have ever had. No more Maytags!

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

We purchased the Bravos XL washer just over a year ago. It is being replaced 1/10/2017. Simply put this is the worst product I think I have ever encountered. Extremely noisy wash cycles leave residue on the clothes, clothes do not get wet in some spots. This washer is so noisy you can hear it from outside. What an embarrassment. You have to run the clothes twice first with detergent and again without detergent to remove the residue left over from the first wash cycle (not energy efficient at all). If I could give a minus score like minus 10 I would.

I am extremely dissatisfied with the Maytag Gas stove and oven. The setting are too high and you cannot simmer something, it burns. I tried the oven cleaner and my oven is still dirty. The burner knobs do not have a click feature. I came home to a house filled with gas. I was not using the top burners, so I must have brushed up against the burner knob while using the oven. I was only gone an hour, imagine if I had been gone longer and walked in the door and created a spark on the rug.

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

I purchased a Maytag dishwasher in 2010 model MDB6709AWW1. I only had it a year and the control panel went. They came out and replaced it and the guy told me that they were having a lot of the same problems. Now in 2015 it has gone again. It will run, but you cant change the settings. I took out the extended warranty on it and called 3 weeks ago and they sent out a local appliance repair company. This guy told me he had just come from another house with the same dishwasher with the same problem. He ordered the parts and I have been waiting 2 weeks. I called and the lady told me that they changed the part # and that they dont have any made yet and dont know when they will. WHAT!!! How can a company not have any parts made for their own dishwasher. I didnt buy the dishwasher when I bought all my other appliances, because there was a dishwasher here. It was gross and didnt work well. All my other appliances are Kenmore and I will stick with them. Have owned them for years and never had any problems.

Maytag Dishwasher purchased for $634 on 7-6-12 from Lowes. Control panel malfunctioned in August 2014. Started leaking in April 2012. From the online comments, I am trashing this machine. It is not worth fixing it and having it malfunction again. Maytag will not say anything about this, only offers a repair person out to fix. I am very disappointed that my hard earned money purchased a sub standard machine. Maytag used to mean reliability. NO more.

Purchased our side-by-side stainless steel refrigerator. After about three months, we too have a constant puddle of water outside the bottom freezer door. Maytag came out for the first year it was under warranty, each time saying it was fixed. Its still not fixed and its been three years. We have to keep a towel next to the fridge constantly and have experienced floor damage. Class action suit? Sign me up!! My Maytag double oven has stopped working, and my Maytag dishwasher does not clean my dishes at all. I will NEVER buy Maytag again.

My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

I purchased a Maytag Bravos in October 2015 and a month and a half later the machine began to make a tweeting sound and the clothes were coming out incredibly wrinkled no matter what spin cycle I put it on. There were also times when the clothes came out totally dripping wet like they hadnt spun at all. I called Maytag and they sent out a technician from a local store which was not a Maytag store. When I told him what was going on, his response to the machine turning out very wrinkly clothes was, Well, why dont you just chose no spin. I said to him, So the clothes wont spin and I have to take out my clothes dripping wet? Doesnt that defeat the purpose of having a washing machine that spins? He didnt say anything to me.It turned out the machine needed a new gasket motor... after two and a half months... and it would take a week - minimum - before he would come back. Maytag sent me a survey which I filled out and they called a day later. They offered me a six month extended warranty for free. I explained to them that I didnt understand why something mechanical would break after two and a half months but the woman just kept apologizing.

Just bought a washer and my clothes are always left with dust and dirt on them after washing. Called Maytag, they sent a technician over, but he found nothing wrong. Company refuses to do anything about it, including exchanging it for a different model, since weve had it for more than a month. I am extremely dissatisfied since I just lost over a grand on a washer that doesnt actually wash my clothes.

I cannot use my Maytag gas range and oven appliance until I can purchase part #W10213446, which your factory website shows as back-ordered until 2020. This means that I cant cook a meal or have the family and friends Ive invited come to my home for Christmas dinner. I need your help to provide better customer service than Ive received to date through working with the Maytag customer service call center, and the service Maytag parts distributors Reliable Parts and WC May company have received from working through your factory website.Ive owned Whirlpool appliances since I built my home in 1989. When I remodeled my kitchen in August 2010 I chose a Maytag range, fridge, dishwasher and microwave as Id had a good experience with your products for 21 years. Youve built a great reputation for quality products and service, and I hope that you will continue to deliver on the commitment promised in your brand by resolving my problem quickly. A burner control on my three-year-old gas range and oven (model #MGR6775; serial #D00934496) recently stopped working (a Maytag design defect - several screws were too weak to hold the cooktop at the correct level) and your customer service call center referred me to A&E Factory Service for the repair. A&E service staff have been to my home twice and are unable to fix my stove leaving me without a stove for the past two weeks and foreseeable future - as the necessary part, #W10213446, is shown as back-ordered with no estimated time of arrival. The WC May company let me know that your website shows an ETA of 2020 for this part on your factory parts website.When the service repairman informed me that the part was indefinitely back-ordered today, I called the Maytag customer service center asking them to locate and expedite delivery of the part. The line staff and her supervisor let me know that they would not provide that service, as I do not have a pre-existing extended warranty contract for the range. I am willing to pay for expediting the part, but they wont give me that option. So I called the parts retailers covering the western U.S. myself to learn that Whirlpools supply chain is so flawed that it cannot provide a part for a three-year-old range.Whirlpools core principles espoused on your website say that founders Lou, Emory and Fred Upton continually improved their washer; they cared about their community, their employees and their customers. They believed that there is no right way to do a wrong thing. It also states that what truly distinguishes Whirlpool Corporation is our commitment to building strong brands and a loyal consumer base. Were focused on maximizing the benefits of our worldwide network of resources, which is unmatched in the industry.I believe that leaving me for up to two months without a range, so that I cant cook meals for myself every day, and for my family during the Christmas holidays is not living up to your brand promise. Please let me know as soon as possible how you will solve this problem.

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

It sounds like an old threshing machine... I have to close the laundry door it is so loud. People cant believe its a new machine. So saving water is the big deal we hear so much about...but water is the main cleaning agent and it hardly covers the clothes even on a full load coverage. Do not use bleach in the machine unless the load contains ONLY WHITES. It just destroyed a new pink top as it spurts out the bleach without any controls. It does not get whites or clothes clean and just twists the clothes to the point everything you wear has to be ironed. There is not one good thing I can say about this pair of appliances except BUYER BEWARE~ I wish I had read the reviews... Buy the old...tried and true.

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

A washer should last 10 years. Bought it in 2009 - after two years we spent $200+ on seal and bearings. Now, in 2014 we need more seal and bearings and the service tech recommended by Maytag says the cost will be $500+. Machine has a serious design flaw, and bad parts, and bad service.

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

In October 2017, I purchased a Maytag MVWB765FW0, thinking that it would live up to the Maytag reputation but I will NEVER buy Maytag again. This machine is more suitable to wash industrial canvas rather than clothing and bedding. All the laundry is twisted and mangled and ends up in a large tangled ball at the bottom of the tub. My clothing is being destroyed faster than I can replace it.

25 months ago, I bought a brand new Maytag stainless steel microwave. We had upgraded all of our appliances except the microwave when we moved in our home. Our first purchase was the Maytag refrigerator. Should have learned my lesson from that because after less than a year, the freezer on the bottom went out twice! We bought this new microwave to replace an old one that didnt match the other appliances and was worn out. Two months ago, the code SE started appearing and then would go away after a few minutes. Now it doesnt go away and you cant use the microwave. I finally called a repair person since its out of warranty and was told that it would cost over $300 to fix it. Really! Im so angry because now I have to take money. I dont have to replace a microwave that should have another few years of use. Nothing at all reliable about a Maytag. I doubt Ill buy anything else they make.

My dishwasher racks are disintegrating. I called to see what to do or if there was a recall. I was told that problem happens a lot, but there is no recall or other option other than to purchase new racks. I could almost buy a new dishwasher. I bought Maytag so that it would last a long time with few repairs. That has not been the case with this dishwasher. I had a medium grade Sears’s dishwasher for years before I supposedly upgraded to a better dishwasher. Maytag is obviously an overpriced name and the quality of their product is no better than any other cheap dishwasher.

Shame on Maytag! Customer Service is appalling! Paid 2500 for one of their top of the line refrigerator/freezer and had the repair people 5 times in one year. It was determined that it is a bad model number that Maytag wont recall but knows it is faulty. Started with ice build up in freezer making it sound like a plane taking off. It kept running trying to defrost (energy efficient-right). The repairman put in a request to have the product replaced based on symptoms and freezer being at 26 degrees. We had to wait five business days for Maytag to review it. I have a family and was having guests. They told me to buy a dorm refrigerator and they would send me a small credit towards it in 4 to 6 weeks. They finally agreed to replace the known faulty model, but I have to wait for the exchange team to contact me (2 weeks later). I keep calling and leaving messages but cant get the exchange team to even return my calls. I have my sons graduation this weekend and I dont have a freezer and my refrigerator is faulty with all my vegetables rotting within two days. It also took two days to originally get someone in management to call me back (even though it did no good - she cant help me). You cannot talk to management if you call customer service. They downright refuse! What a company!

Should have read reviews. Ill never buy another Maytag. This stove has been bad almost from start. Stove has burned marks from using broil. Repairman told me not to use broil anymore. One of eyes has been worked on 2 times; the knob does not work correctly; when you turn off, it goes past the off and keeps on going to the left. It is very hard to clean surface. I have had a few years. Company paid for one repair. They should have replaced stove from beginning. Not safe.

Three-year-old top load Bravos. Started doing the LD/SD tango about one year ago. Intermittent fault, but becoming more prevalent. Can spend an entire day attempting to finish one load; sometimes must be unplugged overnight to clear faults. Washer receives heavy use from extended family of five adults and two children but has never been overloaded. Machine is horribly flimsy and constructed of the cheapest possible materials. I wish I had removed the back prior to purchase.Just because it is possible to attach a processor to a piece of equipment doesnt mean its necessarily a great idea. Any geek can tell you that the three things most despised by a digital device are heat, humidity, and vibration. A washing machine by definition is an epicenter, a breeding ground, for those specific environmental factors. Well done, Maytag. You have demolished what was, perhaps, the most respected name in the business. Good luck getting that particular rep back. Purchasing a Speed Queen. The living embodiment of old-school. Electro-mechanical timer. Stainless. Porcelain-enamel. American-made. Not one complained on this site. Might just shoot an Office Space vid centered on the demise of the Bravos. This time, its personal.

Friends, Romans, Countrymen, At first I was skeptical and I once thought that I was the only one whose wife complained about the terrible soap stains and un-rinsed clothes. And finally my rinse and spin cycle stopped spinning and rinsing! However, after reading several reviews and complaints about the famous Bravo X He washer by Maytag and taking into consideration that there are over 650 complaints, making mine # 651. I now find I have lost all skeptical-ability and feel that we all may be comrades in this venture of purchasing the new trademark of the trade-mark Maytag. As almost all of us say our previous experience with Maytag was great. My parents had a Maytag since I was knee-high to a grasshopper and we were a family of eight. First we had the one with the rubber rollers, that was a work of mechanical genius. I even remember getting my arm caught in the rollers. Then my dad bought the spin dry model and that lasted a good 20 years. When I say the Bravo X at Sears it looked like the state of the art washer. However, and unfortunately I will have to agree with all of you. It is a piece of scrap metal and Maytag will not recall or recognize their mistake and make good on a recall or something. The least they should do is give us an old machine that does wash and spin to replace the new one that is less than 2 years old and does not work. I sure hope this letter does not fall on blind eyes. I think we may even have a collective lawsuit.Sincerely Yours;Mr. Lost All Skeptability!

After less than two years the commercial washer we purchased from Lowe’s died. A repairman came out after a week and said it potentially needs a new control unit or computer. The control unit is on back order and we’ve been without a washer for a total of three weeks. The situation still remains unresolved and I’m regretting not going back to Samsung. After 9 years with a Samsung washer, it died and Samsung refunded the full price of the washer. It was a poor choice to choose American. :(

Im another Maytag dishwasher dissatisfied victim. The control panel stopped working within 12 months and replacement stopped working after one year, which they say is not covered under the warranty. They make rubbish which are disposable and have lifetime of one year.I feel we have to stop Maytag misrepresenting their garbage and basically defrauding us by selling substandard items to unsuspecting consumers. If you have been victim of Maytag lets join together. I would like to start a group to take a class action lawsuit against Maytag. I am very angry and feel they have to be stopped. All Maytag says in response is to try to sell me a one-year insurance. With the rubbishy quality of their products, they probably make more money from selling insurance than their substandard equipments.

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

I am, was, a loyal Maytag owner. The Bravos design, center hub, catches the clothes and rips the material. Customer service will only state damaged material is not warrantied. So I now have a washer that in addition to washing clothes rips them.

Thankfully, Home Depot replaced the washer when Maytag wouldnt authorize a replacement after I had it for 3 days. Maytag wanted me to order a part, wait for the part, and then schedule their third party service contractor. It’s been about 2 weeks without a washer. Ive been posting about my experience and received an email from Maytag asking me to post feedback on their site, but it was rejected. Their note to me was “Our publication guidelines do not permit content that references a service policy, customer service interaction, or customer service question.” In other words, theyre not at all interested in customer service. Maytag/Whirlpool is no longer the brand to look for.

This is a review of a washer that is no longer sold. I bought a top of the line Maytag washer 45 years ago. After around 25 years the control (all mechanical) started sticking during the cycle. I opened it up, sprayed it with TV Tuner cleaner, worked it a few times, and it has worked perfectly ever since. That is the only problem or repair on that machine since it was purchased!

As all the other reviews day 1 Dryer had no heat, washer unbalanced and knotting all the clothes. Sent out new dryer after trying to fix to no avail. One month after new dryer, normal cycle continues to run and not turn off. Repairs again - new computer board. Now washer is winding high pitch noise level - repair new bearings. Thank goodness for warranty. But washer and dryer act up again. I purchased extended warranty. Washer tub needed replacing because transmission went out, dryer again control panel problems. Last night the dryer started on FIRE. I’m sure because the control panel normal was not working again after it was replaced less than 2 yrs ago. Total time owned 6 miserable years. Going back to basics, ugh....

Our Maytag oven (not sure model) in the first year started doing crazy things with the oven computer. The oven would shut off and come back on and the display would be garbled. Also when my girlfriend tried to pull the turkey out, the rack fell off the left side and dumped all the juices into the oven. She almost got burned and there was a lot of smoke. The freakin rack should never fall off! Also our dishwasher is on its second control board. I lived by Mr. Maytag and his airplanes/helicopters at Crest airpark in Covington, WA. I wish I still did. Id like to ask him what he thinks of his crappy products. You get nothing for your money anymore. Im not sure but Ill bet both of my problems with these products have something to do with saving a buck by making this crap in Mexico or some other *** hole. Im just glad Maytag doesnt make airplanes or medical equipment.

I bought this washer from Lowes in 2013. It worked okay for a little while but lately it stops mid-cycle. Clothes are soaked and all of the soap hasnt been rinsed out. Poor excuse for a washing machine! Will never buy a Maytag again!

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

My washer is great. It get the job done. Have no agitator so I can wash 2 comforters. I really like Maytag Heavy Duty. Can get the job done right the first time. Self clean itself also. Also it is a efficiency.

I purchased a stainless steel (freezer bottom) Maytag refrigerator Model # MFI2670XEM0 in Oct 2012. Since then its been a nightmare. The repairman has been out four times, once being a week after I purchased it. It leaked and ruined my kitchen floor. Call Maytag, they didnt want to hear about it. As of this moment, I have three more things broken on the unit. My ice maker literally takes 3 days to make ice, the alarm on the door is broken, and the plastic crisper cracked and now will not stay in. Called Maytag again and they stated that they will not replace the item with one of equal value. They just keep repairing it. I will NEVER EVER buy another Maytag product again. I spent $1700 on this product and had faith in the Maytag product. That will never happen again. Shame on Maytag for not standing behind their products.

I bought a complete kitchen: stove, fridge, dishwasher microwave. Suppose to be stainless steel. All have rusted out within 6 months. Maytag does not stand behind their products. They sent me cleaners and all my appliances rusted more using their cleaners.

On May 23, 2009, I purchased a Maytag bottom mount refrigerator even though I knew that Maytag had many problems with this product and others. I innocently thought that by the year 2009, all their problems would have been taken care of - I was wrong. On April 2, 2011, the freezer part of the refrigerator was not defrosting. I had to make a service call to replace the control board. On March 3, 2013, the regular part of the refrigerator was not cooling. I had to make a service call to replace the control board.Complaining to Whirlpool is a waste of time. The best answer I have received is, I am sorry. There is no end to the garbage Whirlpool is manufacturing and by my experience they dont care. Why dont we, the consumers, hire a lawyer and start a class action suit to let Whirlpool know we are fed up with being ripped off?

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

Maytag Frenchdoor MFX2570AEM3 - Was initially really excited with this brand new fridge. We have not even fully paid it off, as we bought with credit at Home Depot, and it continuously leaks water from freezer! I have taken everything out, defrosted, spent about two hours pushing hot water through the freezer drain with a turkey baster and it was only about four days before I had a puddle on my floor again! We have bought quite a few maytag products before, but after this fridge, probably never again! If there is a recall or a lawsuit pending, please, someone advise me of either.

This is probably the worst place ever to buy any appliances. They are extremely unreliable and the technology on them sucks. If you wanna buy new appliances I highly recommend you spend your money elsewhere. The customer service is extremely horrible and is a disgrace. Shame on this company. They lie about when they will repair your stuff too, so dishonest and I hate this company.

When I went to use this machine (maytag bravos). I noticed there was like a 1/4 filled in tub, checked water flow, that was fine. Then read the manual that Maytag sees using Less Water is better for clothes, I always thought it was less detergent, ohh well. Wouldnt recommend this item to anyone.

How can any company with a reputation that we all have grown up with MAYTAG pull such a DESPICABLE act on its customers of 20, 30, 40 plus years ??? $500+ repairs for each of 2 boards in nothing better than a BOAT ANCHOR... I would give anything to have my 15 yr or even 20+ yr old pair back! Worst purchase of our 50 years of life! Its overdue time for a Class Action Lawsuit! Also has no one had your washer jump and dent your dryer? Imagine a child in a room with something as Vicious as MAYTAG BRAVOS! Just as well have them play in the STREET! Lets all join together and show MAYTAG the consumer does count. Thank you...

3 years into the buying of a Maytag Bravos XL MCT washing machine (Serial # **) and already had to replace the original control panel for a cost of $400+ in less than 2 years of the buy. Now AGAIN the replaced control panel is now once again shot and the machine is not starting. The appliance needs to have a #manufacturers recall for the control panel. #Maytag #Whirpool #BetterBusinessBureau Note -- all existing customers, please lodge manufacturers complaint for the control panel issues @ 1-800-344-1274. (Even if you dont pay because of extended warranty or plan coverage, if you are facing the control panel issue year on year). All future customers, buy this appliance at your own risk.

This is my THIRD dishwasher, and by far the best. The Bosch machine I had before that was a catastrophe: mediocre cleaning, intense filter cleaning required - at least every two days - and, with a pretended noise level of 47 dB, MUCH noisier than the 50 dB announced by Maytag. Somebody is laughing at someone! To sum up: the Maytag MDB4949SHZ cleans dishes incredibly well, is very silent and requires no filter cleaning.

Recently started having puddles of water on floor every morning. Just noticed a thick sheet of ice on freezer floor when I had trouble closing the freezer door. Also the water dispenses very slowly. Removed filter and it would not dispense at all. Will try melting the sheet of ice to see if that helps. Purchased 2011.

I have a Maytag dishwasher; a nylon roller for the upper rack cracked. It is held in place by a hex head screw. The roller is about $1.75. Maytag will not sell me the roller. I have to buy a complete rack adjuster assembly for $46 to replace a small nylon roller that screws in. I have had these problems before with them. I guarantee that I will never buy another Whirlpool-manufactured appliance. This is ludicrous!

Was coerced into purchasing this fridge three years ago. Told how Maytag is the highest quality fridge etc. From day one it was noisy and seemed to be running half the time. I had asked for a quieter fridge, partially why I paid $2000 for it. Now there is something wrong with it. Not sure what yet. But for $2000 it should not be failing three years later. My Samsung was quieter, 1/3 of the price and lasted at least 8 years. Thought about calling customer service but read too many bad experiences here in regard to that. Will never use Maytag again.

I owned a Maytag Neptune washer and dryer for 13 years and never had a problem. The only one thing I would say about them is that since the washer had no agitator it would often tangle the clothes, but they were clean and not damaged so I was ok with that. We moved to another house in July 2016, and the moment we plugged in our dryer there was a spark and smoke under it. Our dryer was fried and it was because the previous owner put in the 220 outlet and wired it wrong. So our dryer was dead and cannot be fixed.Since the washer had the small problem with tangling clothes together, I convinced my husband to get a whole new set, not just a dryer. We went to Lowes and picked out a new Maytag Bravos XL, thinking that the brand was reliable and they were so big I didnt have to worry about doing bedding in it. Like ALL of the other reviews of this set, DO NOT BUY THEM! The washer does not use enough water to wet the entire load and you will be left with soap residue on your clothes and they will not smell fresh and clean at all. In fact, my son sometimes wets the bed or has dirty underwear and that is what my entire load of laundry will smell like when I wash them. Imagine taking a load of dressy work clothes out of your dryer and they smell like dirty underwear!I have tried other settings, different types of soap (liquid versus pod, etc) and doing smaller loads. None of this fixes the issue. It is obvious that Maytag and Lowes will do nothing about this issue, according to other reviewers, so Im not even going to bother to have them come out here to do a service call and charge me for it. So Im stuck with a $1,500 garbage laundry set! (Actually the dryer is fine, it just takes longer to dry than Im used to). Im all for a class action suit to get our money back and force them to stop producing such crappy products! Also, if you are considering this set, keep in mind that they have just over a 1-star average rating on this site, and that is because every reviewer is forced to add a rating of at least 1 star. If not, I think wed all pick the zero.

Dinner ruined again... I bought all brand new Maytag stove MERS755RAW, I can only use one area and that has cant move them, the racks fall through. I have burned myself time after time when attempting to pull the racks in or out. Friends arrived and when we pulled cooked dinner out the rack fell through and it was so hot I could not hold it causing the entire dinner to come crashing down and spilling everywhere. I along with my family cannot use it again. Can anyone assist or make a recommendation? New racks do not work as it appears that oven has expanded and the dimension have changed. Do they have a recall or safety repair bulletin?

I purchased a washer in July and its already off track. When I seen it I know it was junk but the sales person assured me it was a good product. 3 months later its off track. No spinning. DO NOT WASTE YOUR MONEY.

I bought this machine a year and a half ago. The entire drum and spin motor need to be replaced. Maytags warranty only lasted 1 year. I bought it at Home Depot, and also purchased the extended 5 year warranty. The extended warranty is as bad as the washing machine. I am now just 2 days shy of 4 weeks of trying to deal with both parties. Ive had to take my laundry in to have it done. The cost of the laundry, the cost of the machine, and the cost of the warranty is more than $200 more than what Home Depots Extended Protection Plan is willing to reimburse/refund. Home Depot does as much as Maytag when it comes to standing behind what they sell. An $800 washing machine only good for 18 months, really???

I called Sears to have a simple repair done to my Neptune washer and received a quote for $800.00++. They gave us a coupon to get a new washer at Sears and we did. Last week my dryer broke and I looked the repair up on Youtube. It looked real simple. A quote for $270 was given to us. Again a coupon if we wanted to buy new. It seems to me Sears jacks the price up on its parts and labor in order to push the customer to buy new. So far its worked for them and Im sure everyone else as well. Its not going to work out for Sears this time. Im no longer doing business with them and I will do the repair myself. I still got stuck with the service call but that will end as well going forward because I know now what the game is. Shame on you Sears. Double thumbs down for my Maytag Neptune washer and dryers.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

We bought the Bravo washer and dryer in 10/2009. Since then the dryer has never worked well. Weve had at least 8 service calls on same and the sensor doesnt work, i.e. says the clothes are dry when they arent and we always have to run them through at least two-timed cycles to make them completely dry. The washer is another nightmare. At least 8 service calls as well, and after one where the motor was replaced, it popped off and flooded my entire house. They laundry room is located on the second floor. I had to replace floors, walls, ceiling, light fixtures, etc. Insurance covered it but it never shouldve happened. Now the washer doesnt drain properly and the error code LD displays every load and we must manually drain it by either setting an extra drain cycle or take the entire machine apart and vacuum out the water. Each load takes twice the amount of time it should, if not more. But I guess its okay because the dryer takes just as long to dry a load of clothes. Something has to be done. Maytag is refusing to stand behind their products and it seems as though many of the complaints are for the same issues. Is there a lemon law for household appliances?

I purchased range in January of 2011. I have had the top replaced and still it looks bad. Every time I use a burner, even if boiling water, I need to use the razor scraper to clean the burner. I’m very dissatisfied. We used to say we would buy nothing but Maytag but not anymore. Tell anyone who will listen how much I hate this stove. Oven does not cook properly, burns most everything I bake no matter if I lower the temp and time!

Purchased my Maytag in November of 2010, with the freezer on bottom. Within 1 year the ice maker stopped working, and every 8 to 10 days it gets a sheet of ice on the bottom, and water runs out all over the floor. Guess, Yes the warranty expired and scared to death that Im gonna have to replace my floor. If there is a class action suit out there please inform me.

I dont know anything about the Maytag washers and dryers but have a Maytag washer and dryer. And I just recently bought a house that the owner is leaving both the washer/dryer, and both are Neptunes. I have an older set of Maytag washer/dryer and they are about 20 yrs old. They are both top load and I had one repair where a water line had a small leak and the service man came and fixed it and havent had any problems since. So I came on Maytags site to see how good these are, but from what I read, I think I will give the set of Neptunes away and just keep my old set as I am told them will last a good 35 or more years. They are heavy duty and large capacity. Thank you for letting me comment on your washers and dryers.

I bought this washing machine approximately two and a half years ago. I replaced the agitating wash plate three times. After several months, the wash plate will start free spinning from the gear and will spin like a top. It has to be replaced at $140.00 plus the service call. When it was working, it doesnt clean the clothes well. I contacted Maytag numerous times about this problem and they basically gave me a tough luck answer. I just went purchased a old style machine with a tall agitator that will clean like its suppose to. Its a shame Maytag has no compassion to try and compensate customers for the expenses. I also contacted Whirlpool which took over Maytag. My rating is a negative five.

Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

Maytag Neptune MAH8700AWW and MDE9700AYH Washer and Dryer - Electrical overload to house circuit, multiple water pump replacements (Maytag would not sell rebuild kit with impeller and gasket or seal causing us to have to buy complete water pumps with mounts and motor.), electronic error readouts, odor and mold washing machine. The welds breaking on the drum causing possible fire hazard by filling case up with dryer lint fibers, around the electrical components, and air intake heater and also allowing metal fragments to get imbedded in the familys clothes. Also, Maytag Oversize Capacity Plus Quiet Pack Heavy Duty with Lifetime Tub.

This is Maytag model: MVWB765FWO-Top loader. HE rated. It handles mixed loads without balance issues but I cannot yet address reliability. The new machine averages 7+ loads weekly and is in the 8th week of use. The overall performance is clearly superior to the Kenmore Elite it replaced.

I purchase all new appliances in 2010 when I built my new home. The dishwasher, stove, and over the stove microwave are Maytag. Thank goodness my refrigerator is a Kenmore. My microwave is coming up with the SE or 5E code and wont work. It would cost more to have a repairman come out and fix than to buy a new one. And from the reviews I have read it would just happen again. I cant believe with all the complaints about Maytag that any stores are still selling them. This company should be sued for selling such pieces of junk and taking our hard earned money for them. Never ever buy a Maytag anything!!!

Never liked this machine. No flexibility in settings, ruins clothes, noisy and often shuts down. But main concern in the fact the whole top is rusting by the bleach dispenser and it leaks from the top all over. It is only 3 or 4 years old. Can not believe an expensive product like this can be so bad.

First bought a nice looking Samsung. Didn’t last 6 months. Upgraded to a nice Maytag with steam and have never regretted it. It’s been years of worry free and trouble free use. My Samsung dryer is on the way out the door and to be replaced with a Maytag too.