The top loader washer Commercial Technology washes very small loads well. I bought it for the deepwater wash. It DOES NOT work. It also has a auto sensing. Hate this washer. I have to pour buckets of water in the wash to fill it. Maytag/Whirlpool go back to the way it should be. If I want a full washer I should have it! At the end of the day IT IS MY WATER BILL!

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

Maytag Centennial eco conserve clothes washer - I purchased a Maytag (non-agitating) washer, (model MVWC400XW) just about a year ago and I cant tell you how dissatisfied I am with this product. It does not clean the simplest of soil from garments. I have actually had clothes come out of the washer after a complete wash cycle, with dry clothes. They recommend putting soap in first, at the bottom of the washer and then load clothes; I have had clothes come out stained as a result the clothes sitting on top of the soap. I am requesting that I be able to return (have this washer picked up) from my home and replaced with a washer with an agitator or a compatible washer that actually washes clothes. I believe that this may qualify as a lemon with regards to California lemon laws.

I was repairing this Maytag Maxima washer and was almost electrocuted. I simply grabbed the wrong screws which were too long for the door switch, one screw went through into the open/close switch and contacted voltage, thus causing a direct short to the chassis and me. It also damaged my control board (the most expensive one in the industry), now Im out an extra $220 because Whirlpool made an engineering error. A screw should not be located so close (millimeters) to a voltage source where a simple mindless mistake could cause electrocution and possibly death. As for the washers operation, the drain pump failed after just two years, it sometimes leaks water out the front because debris gets into the boot drain back holes. It smells like mildew even though we leave the door open, my clothes stink, Affresh is costly and really doesnt help much. It does a decent job of cleaning, not as good as the old top loaders but it saves water. I think next tax return time this machine goes up for sale and we get a better machine.

I have been trying to solve the issue with my washer, that my parents bought me for my new home. Home Depot, where they were bought, came out twice, and all they say is there is nothing wrong with the washer. There are plenty of things wrong with the washer. It doesnt clean the clothes. I have to use the heavy wash cycle, to try and get the clothes clean. Maytag wont even deal with the situation. The fight has been going on for over 2 years (washer serial # is CY4744432 manufacturers number is MVWC6ESWWI).Not sure if I should just give up. Im really tired of fighting with Maytag and Home Depot. I hope you can help.

My Maytag dishwasher MDB7749SAM is not quite 5 years old. At the end of December 2016 a bubble appeared on my vinyl floor. The plumber could not find any broken pipes or reason for any moisture to have gotten under the flooring. A flooring company did not know what was causing the bubble, moisture or the vinyl glue had failed. The floor got worse and worse, more bubbles.Called the flooring company again. Raised the register cover and could see all the moisture under the vinyl and underlayment. Plumber discovered the dishwasher fill valve had failed but because there was so much insulation on the kick plate, at the bottom of the dishwasher, it forced the water, which was in a pan under the dishwasher, to push the water to the back by the wall and under the flooring. Plumber said, the insulation acted like a dam to keep the water from showing in the front of the dishwasher. The first and subsequent bubbles, in vinyl were 3 feet away from the dishwasher. No way to tell the dishwasher had the problem. Has anyone experienced this problem? If not, take care to remove the kickplate and check your dishwasher for water problems.

Im told even though my fridge is leaking water and making sizzling sound nothing can be done and my model number and serial number match the recall for this product and I was told that if my fridge catches fire then, Call us but to me thats ridiculous.

After first dishwasher was recalled, this one (installed less than 4 years ago - Oct. 2010) had the electrical panel burn out - two years ago. Now - for second time. LAST TIME BUYING A MAYTAG!

Ive had my Maytag oven for about 5 years and the oven and burners are still working perfectly. The problem is the light bulbs. One of the light bulbs has a rickety connection because I have to keep twisting the bulb every time I turn it on to keep the light on. My other light bulb burned out and Im not replacing it because Im concerned the problem is in the electrical part where I screw it in, not the bulb itself, so Im leaving it off and am using the other annoying bulb and I installed a lamp under the counter to compensate for the missing light from the other stove bulb. The most important part of the oven are the cooking features so even though the bulb situation is annoying, it cooking features perform well.

Maytag 18.5 cu ft Bottom Freezer Refrigerator purchased 12/10/12. 1/12/16 the bottom of the freezer had an inch of ice that leaked onto the floor. My plumber chipped away ice and unclogged drains $97.50. 4/19/18) the same $97.50. 5/22/18 an appliance repair business installed a drain kit $148.40. This was his 25th Maytag with the same problem. A whole website has complaints about this problem. I sent a letter to Maytag and they wanted to send out their technician to find out the problem (with a service cost to me). With all these complaints, and a kit to fix it, they already know the problem but refuse to do anything about it. Maytag used to be a reputable company. No more. The customer service said I should have bought an extended warranty. I said a $1400 refrigerator should last longer than 3 years (the first leaking occurrence). I will never buy a Maytag product (nor Whirlpool that makes it).

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

We bought a top load washer and the matching dryer. A thermal switch (I think it’s called) blew in the dryer at about two years. Luckily my husband is an electrician, so he took care of that. WASHER-A little after 2 years the plastic “driver hub” stripped And the agitator has stopped working, the door is having trouble locking and it won’t spin fast enough to get the water out of the clothes. I’ve ordered a new “driver hub” for $53! It is a cheap plastic part. Probably 1 cent to make in China. Robbery. This will hopefully resolve all 3 issues I’m having with the washer. They even charged me 9.99 shipping. $2000 later Maytag/Whirlpool should treat their customers like royalty. I will never ever buy another Maytag or other brands associated with Whirlpool ever again.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

One month after warranty we had our first issue which cost us $380. Kinda my fault I was told by repair guy... My bra underwire came out during wash and destroyed the part we had to replace. Then a year later during spin cycle it sounds like an airplane taking off for about 10 minutes. Its so loud we cant even hear our TV! So guessing its bearings gone bad now? Which is a very difficult part to replace. And pricey. So guessing a new washer is in our future. We previously owned a Maytag washer and had it for 15 years and it still worked fine, we just wanted to upgrade. Big mistake! I wouldnt wish this washer on my enemies. I think the repair guys sets it to mess up when they do this reset thingy. Lol. Cause within a month of the renewed warranty we purchased was expired is when the 2nd issue began. I think the older washer are better because all this newer technology stuff is crap!! My advice do not buy Maytag Bravos series washer unless youve got lots of cash for repairs!!

Not only does dryer come with missing parts and are told by Maytag 1 to 2 weeks for delivery or drive 25 miles to pick up one. You do not qualify for rebate even though you do not receive washer and dryer for 5 days after rebate starts. Should have kept my old GE was faster and got clothes cleaner. Was looking at a Maytag refrigerator not anymore with their service.

We purchased our Maytag Refrigerator brand new, about 18 months ago. It always ran loud so the repairman came out during the 12 month warranty period. He told us to unplug and reset it, but that never did the trick. Eight months later, the fridge stopped cooling. We called our local repairman and he told us ($97 later) that the compressor was out. He said we should contact Maytag because the compressor should be under a 5-year warranty. Then the nightmare began. I spoke to four different reps with a total hold time of about 2 hours. Two of the reps put me on hold to get a supervisor and/or consult another rep and I was mysteriously cut off each time. One rep told me my compressor wasnt covered under warranty. The last rep I spoke to told me it was covered and he scheduled a Maytag repairman to come and replace the compressor. I was thrilled. The repairman came out and informed me that the compressor was indeed out and handed me a bill for $137. I asked why I was being billed and he said because that was the way that Maytag had ordered the service call. I told him that the Maytag rep had assured me that Maytag was covering the repair. He apologized and said that not only was I obliged to pay for the diagnosis (which I didnt need because I had already paid my local guy for the same information), but that it would cost $900 to replace the compressor. I was flabbergasted. I called Maytag and they denied all responsibility. They said that even though the rep had assured me of Maytags commitment to replace the compressor under the 5-year warranty, he had made a mistake and I wasnt actually covered. So I paid our local repairman to replace the compressor, because by that time, we had been living out of ice chests for 2 weeks. That was 3 weeks ago. Now the unit is freezing water on the bottom of the freezer and then leaking water on the floor. It is unconscionable that this company be allowed to defraud people to this extent. I will never buy a Maytag again and I would like to be informed of any class action suit. This company should be deeply, deeply ashamed of itself.

MHW7100DW Maytag Washer Steam & YMED7100DW Maytag Dryer Steam. Both of them are easy to use. They hold lots of clothing as well as bedding and many different settings. They both do an excellent job. Brand and excellent reputation. Had my last Maytag washer & dryer over 25-years and had no problems with either. Thats why I bought Maytag again. Repairs are very costly when you have to pay technicians. Dont like poor quality construction or enamel chipping when you place items on them. Very easy to clean both of them. Practically no lint dust emitted into the room from the dryer. Had no problems with my previous washer & dryer. Thats why I purchased a full size Maytag washer and dryer again.

Waste of $1700. Well all I can say is I wish I woulda read these reviews prior to buying but thought Maytag was a good brand. Boy was I wrong. Never again will I purchase Maytag products. I must say I haven’t had any issues with the dryer. Works great. The washer on the other hand is garbage!! It barely cleans the clothes. Some articles only get partially wet. Everything tangles together. The worst part is all my dark clothes ends up full of dust and lint. They look dirtier coming out than when they went in. Very disappointed. If you use deep load it takes about 1 1/2hrs to wash, definitely not energy efficient, and clothes still have lint on both cycles, and unfortunately most of our clothes need to be hung up, so dryer can’t pick up the lint. My old wash was way better. I shoulda went for same old style. Save you money and buy another brand.

Do not buy a Maytag Washer. I had a Maytag for 25 yrs with only 1 repair in its 23rd yr. When it finally retired at age 25, we replaced it with another Maytag assuming it would also last long. No chance. We had only 2 good yrs. Now, at 2 yrs old, it is so so loud during the spin cycle that it sounds like an airplane (757) is flying overhead at 50 ft above the roof... No way can we possibly use the washer if anyone in the house is sleeping. Repairs cost more than the initial price of the washer. Please do yourself a huge favor and buy another brand. There are too many complaints about Maytag to even consider purchasing one. Not worth the aggravation!!

Fridge model mff2055drm00 - Purchased 2 years ago. Upon delivery and working water leaked from bottom. Called recommended service. Result took out fridge and brought in another new one. Today the fridge/freezer ices up, ends up sounding like a rocket ship. Not working efficiently. Called for authorized service. Was told needed a new thermostat... after TWO Years? Service call price $125, quote to purchase, replace and install thermostat $550. Almost $700. Big mistake buying Maytag- who knew? But never again! We are quite angry and very disappointed with the mediocre performance of this product.

I, like SO many other people, am experiencing problems with a relatively new Maytag dishwasher. Mine is Model MDBH979SAB1. I have owned the dishwasher for 4 years but use it 6 months of the year and, because I live alone, maybe twice a week. In effect, it has the equivalent of less than a year of normal use. My problem is the same as countless other people. I can tell from how it behaves that it needs a new control board. I find little comfort in the fact that I one of several thousand people experiencing a problem with a newer Maytag appliance. What concerns me, after reading many negative reviews and seeing Maytags response, is that Maytag does not seem to care. We need to get the word out. We need a massive boycott of Maytag. We need to hit them where it hurts: in their bottom line. Since they seem to be content to continue to put out defective products, the only way to protect consumers is to put Maytag out of business.

Control panel start button failed 55 weeks after purchase and installation. Model no. MDB4709PAW. Repair costs for labor and part totaled $298. I have since found out that Maytag dishwashers with this type of control panel are faulty and fail often within first 3 years. Purchased at Johnnies Appliance, Glendora on 6/14/14 NJ; ticket no. **.

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

Bought a Maytag washer from Lowes 3 years ago and it is just junk. I am 62 years old and never had a washer that actually broke down. What happened to good American technologies. I guess those days are gone, anyway dont buy a Maytag, duh. It is the day after x-mas and I have to buy another machine.

Wow! I wished I had reviewed this page before purchasing a Maytag. We bought a new Maytag Range (#MGR5751BDD) from Menards in March 2008. Within a couple of months, we were out of a stove. I was lighting the burner to make dinner for my family (it is a gas range) and all the burners started making a clicking noise and they caught on fire. Luckily, my husband was nearby and took the fire extinguisher to it.We thought for sure that the house was going to be gone. We contacted Maytag and they had a guy come out (wasnt the friendliest and cted like he could care less). He stated there was wiring that was bad but because we took the fire extinguisher to it we probably voided the warranty. What? He would submit a report to Maytag.Maytag reluctantly gave us some money but not near enough to cover the stove that was only a couple of months old. Now, I cant use the new range that is 2.5 years old. It pops and spurts because the regulator needs to be replaced. The bad thing is by the time we pay for a repairman and the new part, it will cost us a lot of money we cant afford. This stinks.

I have owned two Maytag washers. Top load and front load. They have been the biggest piece of garbage I have ever purchased. My current front loader eats and destroys clothing. I have had to throw out numerous clothes as the machine simply destroys them. I have also had numerous problems with Maytag washers. The wiring is garbage. Couple yrs after purchase the washer shorted out. Im handy so I took it apart. Discovered a broken wire. I had to rewire a new connection with as. The wire used in manufacturing is so thin its line a strand of hair. Now it leaks under the drum. I had to place a container under the drum to collect the water. My other purchase was a top load. The lint was just a nightmare. Maytag sent me some contraption after numerous complaints that was suppose to assist in the collection of lint. Again, a piece of garbage. DONT BUY. Save your MONEY.

Bought a new home in July of 2016 and the builder had included a Maytag Bravos XL washer and dryer. They are THE WORST performing appliances I have ever used! I will replace as soon as I have the means to do so. DO NOT PURCHASE the Maytag Bravos XL appliances. The engineers that designed them should be fired! The washing machine makes an incredibly loud noise (like an old starter grinding in a 50s car). Im told that this is normal for the machine. Does NOT clean well and leaves soap spots on dark clothes... leaves them on light clothes but I cannot see them. Whites come out dingy even with bleach. The tub is so deep that I have to use tongs to get out smaller items, I am 53 tall and have never had this issue before. Soap dispenser drawer wont stay closed during wash cycle. Clothes are so badly tangled during the wash cycle that it is hard to describe the wrinkled mess that has to go into the dryer.Dryer issues: Very loud. Very wobbly and unstable, and yes, it has been leveled 3 times. Bed linens have to be separated at least 3 times during the drying cycles because they twist and wad up into big, wet knots of cloth. Infuriating!!! Dry time is very long unless you wish to cook your clothes. So disappointed in this product. Total rubbish!!

Not long after dishwasher MDB7609AWB2 was out of warranty the START switch on the keyboard would not work. Called dealer and they sent someone out to check for a charge not quite $100. Could not fix it so said it needed a new control panel which with labor was almost $200. Doesnt work so get it fixed. Now less than 3 years later the same thing has happened - wont start. Lousy engineering and part probably made in China to save Maytag money, I feel is the cause. This is happening over and over to those of us who purchased in good faith what used to be a reliable product from a reliable company.

We purchased this double-oven range (model: MGT8775XW01) about 5-6 years ago. It came with some slight bubbling on the plate that the control knobs go through/are mounted onto. A few years later, the bubbling paint began to chip/peel off - revealing rust (its a white range). I bought some touch-up paint, but that didnt look very good. Now that entire plate is bubbling and peeling and makes the whole range look like crap. My wife swears well never buy another Maytag product...EVER! Shes ripped! I cant seem to find the replacement part to purchase. Lousy products!

Maytag Bravo Quiet Series 300 MVB700VQ - My wife and I feel this is one of the worst machines sold. We purchased it from Costco 2 yrs ago and had several issues over the years. Pump, locking, water level, small clothing items like socks getting in behind the drum and clogging the pump, and yesterday a flooding issue. That is right, my Bravo 300 did not shut off and the water ran continually with an LD code displayed. The water overflowed into the kitchen & pantry. The wood floors are now warped. We were home so we were able to shut off the water as the washer controls (buttons) were locked and not responding. We spent the better part of 3 hours moving items and wet vacuuming the house. We now have a dehumidifier running in hopes we can salvage the wood floors and minimize mold growth.I will note that I have a home warranty (third party) that covers repairs on my appliances, this washer included. The repair man thought it may be the pump, a line, and/or the control panel/module that need replacing. The repairs would be covered by home warranty.... but not the floors. There is NO WAY I am fixing any washer that flooded my home.Yesterday, I took a 3 yr old washer with known issues back to Costco. I was not happy with the manufacturers suggestions that I buy parts as it was Out of warranty. Again, I had a third party warranty so the repairs would have been covered! It is clear that the manufacturer doesnt CARE about the quality or the performance of this machine. I have found a FIX for these issues. We are buying an LG Washer that is more $ and is highly rated by Consumer Reports. Stay AWAY from this model and current repackaged models of Bravo/Cabrio!

Hello, I purchased a Maytag Bravos washer model MVWX655DW from the Home Depot in June of 2017. I can provide the receipt. Within 6 months I had a broken lid switch and the unit would not move through the cycles. Luckily, I had the ability to replace the lid switch at the cost of about $100 just for the part. The repair was fairly involved. This summer, the unit failed to agitate, upon much research, I learned the washer drive hub (which makes the washer agitate and spin) was worn out. It was made of plastic and it is quite a job to get the cover plate off and to replace this part which ranges in price from $20-$45. This is a fairly difficult job and I would not recommend it to most people. It should not be needed in a 3 year old machine. Upon inspection of the drive shaft teeth when I took the washer apart, I found the steel teeth to have significant wear. Why? Now, in mid-November, same issue, the plastic drive hub is worn out again! I was told maybe my shock absorbers for the drum needed to be replaced as the drum may be shaking too much. My previous washer was good for 18 years and I replaced it with this highly recommended model Maytag with the chrome basket. This is absolutely the worst appliance I have had and with every repair, I viewed many, many people with the same complaints and feeling that Maytag should issue a recall on these machines. I will be contacting Maytag and Home depot with my review. The HD installer also stripped the plastic valve one of the water hoses goes on that I had also to replace. A $40 dollar part. This took some disassembly but not as bad as replacing the drive hub every three months. Needless to say, I have to buy a new machine after 3 years of unreliability with his machine. A waste of $500 + of my hard earned money. Very, very disappointed. If I wasnt mechanical and able to fix this washer, it would have cost me hundreds in repair bills. I have receipts of the parts I have purchased for this unit. I hope your experience is better if you have owned one of these machines. Maybe I just got a bad one but many people have complained about this model so I dont believe I am alone. I hate to see good people spend their money on poorly constructed machines. I certainly expected more than 3 years out of a brand new appliance. Maytag and Home Depot have lost a good, long time customer unless they want to make it right. Please feel free to contact me.

Bought a 2400.00 refrigerator 1 year and 4 months ago. The freezer quit working and we lost everything in the freezer. We called and were out of warranty. The commercial on tv shows the bored repairman who never has any work because Maytag is so reliable. What a crock! We are going to have to pay for the labor which could be as high as 800.00. This is so wrong. This is a high end refrigerator and the fact that it only lasted a little over 1 year is unbelievable. I would dump it if I could afford to. It is a piece of junk. I will never ever buy Maytag again. Make a new commercial, one where the repairman is so busy he works 24/7. We got screwed by Maytag. They do not stand behind their product, they rob you blind.

Im really happy with my range. The only drawback is that the upper oven/broiler is a little on the small side. The five burners on top are convenient for when I am cooking a large family meal on weekends and holidays.

I purchased the Maytag Bravos XL MVBW755DW Washer and MGDB755DW Dryer in July 2016. Shame on me for not making my complaint sooner. They offer the Tide Pods for use but they dont completely dissolve and leave a residue/stain on the clothing. I have to wash everything on Deep Water Wash just to try to get them to come clean. Clothes will come out dry in some spots, they will have fabric softener stains on them, the pre-treated stains are still there once washed. Lint residue will be left on just about every piece of clothing. The fabric softener/detergent dispensers left side is rusting and I have to pull it out and clean it once a week. I cant get to the track on the inside to try to clean it and soon that will deteriorate and the dispenser will no longer slide into place. If I could attach pictures I would. Now moving on to the dryer, it dries clothes great. My only complaint at this point is that when the cycle is getting ready to shut off it sounds like a jet engine and rattles terribly. To sum this up, I called customer service this morning. They said nothing that I am explaining to them sounds as though it is a manufacturers defect. They said they will send a tech out to review at a fee of $99.95 plus the cost of any labor associated with the repair. They did however offer to pay for the parts. Now my question to them is if none of my issues are a manufacturers defect then why would you offer to pay for the parts? The unit(s) are no longer under warranty... Think twice, gather as much information as you possibly can prior to making a major purchase. I DO NOT RECOMMEND THIS PRODUCT!

I bought my washer just over 3 years ago and it started making loud clicking noises and it seems like the agitator function is not working at all. I have a repairman coming over in a few days. I knew I should have gotten the extended warranty!

I purchased a Maytag Bravos XL washer and dryer at Best Buy (Pacific Sales) in March 2013 at Best Buy. I also purchased extended warranty on both machines. A few months into owning the machines, the washer started giving us a UL error light. It wouldnt finish the wash cycle and had to be restarted multiple times before it would do so. I called Best Buy and they sent out a repairman. He said the set-up cycle had not be run correctly by their own installation team (which I paid for), and he said that he had fixed it.A few months later the problem started reoccurring again. Best Buy sent out repairman again who claimed there was nothing wrong with the machine. He left and the problem started reoccurring soon thereafter. I called again, and Best Buy said they couldnt do anything about it because Maytag could only work on the machine (it was now getting an F:51 error message as well). Maytag sent someone out who watched it run for 15 minutes and diagnosed that it was fine and left. I told him that the error didnt occur until the end of the cycle, but this seemed to make no difference to him (he didnt want to wait).Same thing happened again (might run five to ten loads without an error and then it pops up again), and I called Best Buy again. They sent out the Maytag repairman again (different repairman). He spent about the same amount of time as the previous Maytag repairman. His conclusion was that the machine was fine; he told us that this particular washer (the top-of-the-line for Maytag) gets out of balance frequently and that we would simply need to live with it. Like his colleague, though I told him that the error message doesnt occur until the end of the cycle, he didnt stay that long.Not long after he left, the problem started occurring again. I called Best Buy and indicated that theyve had plenty of chances to repair the machine and that I wanted a new one. They said someone would call. The response: another call to schedule a repair visit. I called them back and told them that I didnt want another repairman but rather a new machine (weve wasted hours and hours of our time giving them a chance to make the purchase right). They then had someone from the Geek Squad call, who swore that hed put his best guy on it and that he would actually work on it this time (ordered parts). He was supposed to show up this past Friday but called in sick (now rescheduled for this coming Friday). In the meantime, the machine (last night) quit working altogether. I have a pile of wet laundry and am faced with going to the laundry mat today.Im at an utter loss of words for this experience. It is truly the most frustrating consumer experience that Ive ever had. Ive watched Best Buy, Pacific Sales, and Maytag play pingpong back and forth across the table for months. I paid good money for top-of-the-line washer but have gotten bottom-of-the-line service. Surely, at this juncture, Maytag and Best Buy will finally do the right thing. I am going down to the Best Buy store this morning to visit with the store manager (and then to the laundry mat...not exactly how I wanted to spend my Sunday). If not, then next steps will be to figure out how to find representation to force the issue of the lemon law. Exasperated.

Maytag MHW3505FW Washer and dryer were purchased 13 months ago. I purchased and spent $2,000 because the Lowes salesperson and the stickers on the machine said they had a 10 year GUARANTEE AND commercial quality/technology. Exactly 2 weeks after 12 months the washer started flashing erratically when I was able to turn it on. Wouldnt react to any of the touch controls and stopped working. Called Lowes who told me because I hadnt bought an extended warranty they would do nothing. When I told them I was told a 10 year warranty was in place they said they only cover a year. I was told to call Maytag. Maytag said the 10 year warranty only covers the steel drum and motor! Nothing else is covered after one year. I was offered an extended warranty for $600. Not something I will be doing. I will replace with non-computer washer and dryer and will NEVER BUY MAYTAG again. They should be sued for false advertising.

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

My grandmother got a Maytag Bravos XL MVWB755 washer and from day 1 she had to call Maytag with issues due to residue left on the clothes. They told her to not use this setting... buy this detergent... only use cold water etc. Never did they offer a repair guy to come out. A year passes still having issues shes out of warranty. They now offer a repair guy but claim theyre going to charge her $90. Once she explains to them that she was never offered a repair guy & they shouldve done this before. They decided to waive this fee and send a repair guy. Once the technician comes out to the house they do absolutely nothing and they fill it up with water say we need to clean it and Ill come back out and do another diagnostic. When they come back all they do is fill it up with water get a glass check the water and say, Nope, no floating residue. Everythings fine. They then tell her she needs to get a water softener which is going to be hundreds of dollars.The technician also says do not use any other settings except for these two. Can someone please explain to me why they have all these dang buttons and settings if were not supposed to be using any of them and why all of the clothes come out with soap residue scummy residue all over them? The old washer never did this. It was a Kenmore and its the same water same everything but this Maytag washer is been nothing but problems. It leaves the residue which is stripped all over dark and white clothes, it is extremely loud, not all the clothes even get wet! Maytag is been extremely uncooperative with assisting my Nana. They tell her no one else not one other person is having this problem but when I look up this issue I find that about 2500 people on this forum are having very similar problems. Something has to be done. Maytag should have to take responsibility for this washer. The bottom line is it supposed to be an XL. When my grandparents are washing its only for two people. Theyre not even filling that washer up of all of the clothes are not even getting wet. It just goes to show you that the energy-efficiency that they claim is not working. The washers not getting enough water inside of it. Its not fully rinsing the clothes and no one should have to put the clothes in wash them then do a whole another rinse cycle just to get the dang soap off. So basically at this point she stuck having to do multiple washes using way more utilities than she should have to and Maytag is basically going to do nothing. It wont help her over the phone the technician is a joke and it looks like so many of you people are having the same issues.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

The Maytag Centennial (Model MVWC6ESWW1) washer was purchased in September 2009 and within 18 months no longer provided water at the temperature selected on the control panel. The problem started after we used a spin setting to remove water from a cycle that did not complete itself. Somehow selecting a spin cycle disturbed the water temperature control mechanism. We were advised by Sears to unplug and then reattach the electrical connection (similar to rebooting a computer), but this was not successful in water being delivered to the washer at the temperature indicated on the control panel. While there was minor damage to clothing and a waste of hot water before we realized what was happening, the real inconvenience is not being able to rely on the water temperature setting. Based upon reading comments on the internet (including Consumer Reports) concerning this washer, the public should be warned not to purchase this machine. Better still the machine needs to be recalled in order to protect the consumer.

After a year, the plastic parts of Maytag dishwasher is breaking and upstairs propeller is no longer running. Do not buy this product. I made that mistake.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

I bought a Maytag washer 3 years ago. Maytag gave me a number for one of their warranty service repair shops in my area. The first repair service doesnt even respond to my calls. The second repair service is a total ripoff. So in summary, Im stuck with a 3 year old washer that has a broken drive assembly that the warranty wont cover.

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

Within the first month of purchasing my front loading Maytag Neptune washer (MAH6700AWW) at Home Depot, the soap dispenser fell off. The machine not only leaked, requiring stack of towels to be placed on the floor to keep the room from flooding, but often produced foul-smelling clothes, despite cleaning the machine. On top of that, the delicate cycle stopped working and then last month, the entire control board went! It is past its warranty period, and I cannot afford a new washer for my family of 6. The machine has been discontinued and the parts unattainable. The control board of our dryer (MDE6700AYW) went too, causing buzzing in the electrical connection and burning, causing us to have to shut down the circuits for the machine. Maytag has lost all my respect as a quality appliance supplier. We spent $1700 on the set and the machines have been a nightmare. Please note: we were NOT notified that there were class action suits against Maytag regarding their machines.

We purchased a Maytag French Door Refrigerator with a bottom freezer in 2010. About 6 months ago, we noticed water leaking out the front of the refrigerator. We recently called Maytag service and were told that the refrigerator pan was too small and they would order it and have the independent contractor replace it. The woman I spoke with said that Maytag has been having a lot of complaints about this as the pan put in the refrigerator was too small. In my opinion - an obvious design flaw. The service tech came to our house today with a larger drain...not a pan as I had been told by Maytag (Maytag is the one who ordered the drain to be put in). We ended up paying an unexpected $209 (Pan vs. drainage replacement is a lot more expensive). Needless to say, we are upset for having to pay $209 for a Maytag design flaw as well as not being told upfront what the correct part was that was being ordered. We called Maytag and were told there was nothing they could do because its not on the recall list (yet) and because we didnt buy the extended warranty. We are feeling like suckers and will never buy another Maytag.

I have a 7-year -old Maytag dishwasher, which was not working well. I paid over $600 for extra features. Maytag contacted me that the coil had to be replaced. They sent it to me, but the repair service said that theyve sent the wrong one. When they sent the second one, the repair service came out and called Maytag, They said that my model cannot be recalled. The repair service left, and after 1/2 hour later, Maytag called me and said that the repair man has to come back and install a new coil. He came back and installed it.

I purchase my first glass top stove; a Maytag. It came with a 10 year warranty on all elements and the glass top. As this is a first glass top I read through all instructions, there appeared no real warnings on what to do to maintain the glass; or rather what would damage or void a warranty. I simmered some maple syrup, and as it so often does when reaching the proper temperature, it boiled over. On a regular burner, one just uses a little elbow grease and your stove is returned its previous state. This actually pitted the glass, and as the warranty people at Maytag informed me voided the warranty, and seriously weakened the glass top suggesting it would be likely to break. Seriously?????? All of us boil stuff over on the stove top from time to time, and this damages the glass top and voids a warranty??? VERY DISAPPOINTED in Maytags product and their warranty.

Paint bubbling & peeling off appliance: I purchased new double convection oven from Lows (Maytag). One month after delivery, paint began to bubble and peel off. Maytag takes the position that as long as the oven functions properly, the paint is simply cosmetic and the warranty does not cover cosmetic problems. Maytags position is that even if all the paint peels off but the appliance still functions properly, too bad for you!

Refrigerator - The freezer of the refrigerator would randomly leak on the floor. When I had it repaired on 12/30/14, at a cost of $253.97, the repairman showed me the defective part. He confirmed the online reports that the leaking was caused by a defective part. The defective part had been used because it was cheaper. Now the repaired refrigerator works well. Last month, the control panel on the dishwasher stopped working. According to the online reviews, this is a frequent problem requiring that a new control board be installed. The reported failure typically occurs after the one year warranty expires. My appliances are located in a second home so are only used about once a month. A salesperson at a different appliance store said that appliances usually last from 10 to 12 years. The four years of occasional use prior to failure is not acceptable. I would like to have Maytag repair the dishwasher at their cost. How do I get this to occur?

This washer stops every 10 minutes, sometimes taking 3 to 4 hours to complete one spin cycle if it is completed at all. All troubles began shortly after warranty expired. NEVER EVER will I ever buy Maytag again. I make certain that I tell everyone I come in contact with about the pathetic quality of Maytag.

2 years ago I purchased a Maytag Washer & Gas Dryer. Unfortunately, I did not invest or believe in extended warranties. I believe in trying to buy quality products. The door on the washer would not open and 2 error codes were displayed. I was trying to add another piece of laundry and the washer had just started. I canceled the load, waited for the door lock light to go out, but the door would not open. The error codes began displaying E3 and F5. I immediately went to the Maytag website for a resolution. The suggestions did not work and was instructed to obtain service if they did not. I called for a service call for $35, but was told that the repair would be over $300 for parts and that was not including labor. The parts I needed were a control panel and a part for the door lock. This was not a Maytag Company service tech and he told me that this happens because the parts are plastic. Currently, besides a Maytag Washer & Dryer I have a microwave, stove, and dishwasher that are also Maytag. When I replace these appliances, I WILL NEVER BUY ANOTHER MAYTAG PRODUCT. I expect the quality and life of an appliance to be more than 2 years, without buying an extended warranty. When I told a friend what had happened with my Maytag Washer, she told me that she had a Maytag Washer broke down with a control panel problem, and she couldnt remember the other part. She informed me that her repair was over $500.

We first purchased a Maytag Neptune washer and dryer set. We loved them. Had them for 15 years with no problems. When we decided to get a new washer and dryer, we were loyal to the Maytag brand. I was immediately drawn to the Maytag Bravos XL due to the extra large capacity. What a mistake! This washer and dryer pair take more than two hours to complete a single load of laundry. It often takes more than one wash to get clothes clean. If you wash an extra drum large load of laundry, often times there is not enough water and agitation to even get all of the clothes wet. I have a one-year-old boy and a six-year-old boy, their clothes get very dirty. This washer Does not get food off of my one-year-old’s bibs. And my six-year-old’s clothes come out looking as if they haven’t even been washed. What a disappointment! My husband and I are going out today to purchase a new washer and dryer set after having just purchased these Maytags in April last year. What a waste of money! Please include me if a class-action suit it’s taken.

M1BXXLZYB00 - This is the worst appliance I have ever owned and I am 56 years old. Very noisy, freezes my produce and actually anything in the refrigerator. Yet the freezer wont freeze popsicles. Had 2 service calls on the fan and or fan motor in the first 6 months. Now 2 years later we have replaced 2 compressors and had to pay 200.00 labor to have installed. Now the compressor is out again not even 30 days after the first 2. Whirlpool wants to send another compressor and the poor repair guys are suppose to do it for free now because it is within the 30days. The offered me to buy another refrigerator with prices of 699.00 and 519.00. My fridge in the garage is way more dependable than this one and I have had for 10 plus years with no problem.

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

I bought my microwave in Nov of 2015. We began having problems in April 2017. When you cook or warm something up it gets hot. The light wont come on and the display continues to say open/close door. After about 4 hours of cool down time it may or may not restart. After contacting Maytag I was told I should have purchased the warranty. They also informed me that they do not have repairman in my area. We have just replaced all appliances with Maytag so now I am concerned they are all junk. We did buy warranties on the major appliances, but how will they repair with no repairman in my area. Maytag used to be the best appliances but after this experience and now I have a broken microwave after only a year and a half that they dont stand behind, I will never purchase any Maytag again. It also seems that this is not the only issue they are having with their microwaves. I have contacted my Lowes where we purchased and they even made a Maytag call with no results. Maybe the suppliers should stop promoting and selling their items. We replaced a 22 yr old Kenmore microwave that was still working thats why this is so heart breaking. Stand behind your products. No wonder you dont have repairman. They would never get a day off from repairing your junk.

I bought this machine at Lowes because of the BIG drum area and about 2 years ago, it started to make funny noises; then I got the F-51 signal. I tried everything, shifting articles of clothing, then unplugging the machine and re-plugging. I am in the process of researching a plain Jane model, not one with all the bells and whistles. I am extremely dissatisfied and wish Maytag would step up to the plate and recall these machines. A motherboard and the costs for other parts, I would be better off replacing with a brand new machine. Dissatisfied!!!

We have a 4yr old model MFI2665XEM7, just started leaking water every other day. A puddle wipe it up and its gone. Have ice build up on the bottom of freezer. Any suggestions on what to do?

We bought a Maytag Neptune Washer and dryer package from Home Depot in 2004 and had nothing but problems ever since. Such things as washer had mold constantly. Also, clothes seemed to have a foul odor after washing. The dryer always seemed to have to be ran twice to get clothes dry.

We purchased our Maytag Bravos Top Load washer 3 years ago from Home Depot. I have to admit this is the worst washer ever. The clothes does not appear to get clean enough for the amount of time it takes for the clothes to wash. The white clothes look dingy after a wash that I have gotten to the point of pouring an additional amount of bleach in the wash tub. The amount of water that is in the tub is next to nothing, I have to either add additional water or place no more than 20 pieces of clothing in the wash. This is sad and I regret that I wasted my money on this product and I do not recommend it. As soon as I get some extra money to throw away, this washer is going out with the bulk trash.

Range is at least 20 years old and everything still works w/o issues. Our model has an upper level and a larger lower level that is a convection oven also. The top one heats up real fast which is great for quickly cooking and reheating. The lower one is large enough for everything else.

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

I purchased a Maytag quiet series dishwasher (Model Number: MDB6759AWW) for $500.00 in May 2009. Three months later, I started experiencing difficulty with the control panel. One light would continue to blink and it would not do anything else. I called to have it repaired but by the time he was to come out, it started working again only to stop working again the next week. On 7 Oct 09, the repairman came out and replaced the panel. Then, about six months later, it stopped working again. I called again but canceled the appointment because it started working again. Then, after having it for one year, it stopped working again and I called only to be told that it was no longer under warranty. Now, we cant get the control panel to do anything. From all the other similar complaints I have read, it seems like there is a defect with the control panel. A dishwasher should last for more than one to two years. This is very frustrating.

When my husband surprised me with a double oven stove I was leery. First Thanksgiving my thoughts were concurred as the 20lb turkey fell from the chinsey rack.....even a cookie tray with almonds fell down.... Unfortunately the lower oven is off by 1/2, no racks work in there. My biggest gripe is that the seller did not exchange it, just tried more racks. Now Maytag will not do anything but allow me to order more racks. This item is a huge piece of junk.

This machine sucks. Im down to washing three to four items only on an extra capacity machine because every single load becomes unbalanced. Feeling the weight of each item and then placing it correctly doesnt work. Repairman came out. Said it was balanced. Lie. At this point I want to take a sledgehammer to it and send the pieces one by one to Maytag. They should be embarrassed to even have this product for sale to the public with their name on it.

Worst customer service ever. I ordered my washer and dryer from home depot 2 weeks before a possible delivery day. The day before delivery I receive a call that they dont have them and I must wait 1 more week. After 3 phone calls I am promised a credit to my account. A week after delivery I am wondering where my credit I was promised is so I call. Im told the most I can be given is $100. I state that I feel my time is worth more than that. A supervisor is brought in and Im told we will get $150 credit. Then put on hold. She reviews account (why didnt you do this first) and told because we didnt call within 48 hrs of delivery the most they can give us is $75. So I call back very frustrated. Then Im told its our word against theirs that we were offered that?!? What?!? Well I am sure you record conversations and thats total BS. I explained how you cant offer something then take it back. I was told the week before I was getting a credit and my account already notated. No one said, Call within 48 hrs to dispute again to get it. Why would I have to I mean seriously. So after a total of at least 2hrs on the phone before and after delivery I am forced to settle with $75. I feel very unappreciated. I purchased and paid for $1633 worth of appliances that were a week later than promised. Called less than 24 hrs before expected delivery and told they dont even have them. Then told Im getting a credit of $150 to be told sorry now just $75. The lady proceeds to say that she doesnt think it was because of the phone call not being made. What? Are you serious. WELL THAT WAS THE LAME EXCUSE I WAS GIVEN SO I COULD CARE LESS IF IT WASNT THE REAL REASON. THAT JUST MEANS I WAS LIED TO. I promise I will never buy Maytag Whirlpool again. One customer may not mean much to you but good customer service means everything to me.

I just saw that there had been a class action lawsuit settled in 2005 for the Maytag Neptune front load washer and I was never notified as an owner! I have this crummy product and have been living with it for more than 10 years! I just scheduled a repairman to replace the moldy gasket (for the second time) and the noisy pump, and a latch that has to be slammed for a sum of $438. What a crock. I was told this was a top of the line model when I purchased it for $999. Ive never had such a piece of junk before in my life. I run loads of bleach weekly to control the mildew.

Thinking it would be dependable and clean my clothes well, I spent $888 online for this washer. Normal use, HE detergent, only adults washing normal loads. After 4 mos., would not agitate, made loud clicking noise, filled and drained. Bought 3yr service plan, and company assigned still tried to charge a fee just to look at it. After 1 week of dirty clothes piling up, bought a Samsung combo, & had the Maytag hauled away. Money on the Maytag down the Toilet! Never again--Maytag, Amana, Whirlpool, etc. All made by same folks and pure trash!

MCT commercial technology washer Bravos XL - HORRIBLE product, NEVER worked right! Maytag misrepresented this washer. DONT buy it! Lie after lie! Its suppose to be high efficiency... conserve water and energy. I have to use 3 times the amount of water and energy because it doesnt wash the first time correctly. Leaves soap in clothes, just doesnt wash properly. I have done EVERYTHING they have recommended NOTHING works! I will NEVER buy another product from them. Even the repair people and Customer people say they have nothing but problems. Im going to small claims court. Im sure with all the problems we could get a class action lawsuit. No stars.

I purchased a Maytag model 4000 Front Loading washer in April 2010 and in May 2011, the tub bearings went out which is a $600 repair. Now in January of 2012, the tub bearings are going out again. Neither Lowes nor Maytag are willing to do anything to remedy the situation. Do not buy Maytag and do not buy from Lowes. Their major appliance buyer has to know about this and continues to retail a product not fit for its intended purpose.

We bought this range (model MER8700DS 1) March 25, 2015. Manual states when you use the oven first few times odor or smoke may happen and is normal. It also tells you this is not harmful but remove birds to another room because the fumes can kill them. Noxious fumes? Forget about the birds! Had to open up the whole house and go outside. Burned my eyes, throat and lungs. Day after day, repeatedly turned temp up to 400 trying to burn off what we thought might be a coating. No luck.Maytag got very concerned when I explained about the noxious fumes and had someone come out right away. Tech took it apart. He removed bottom (screwed in) plate that covers the bottom heating element. That plate gives the added ability to have 3 racks and make full use of the 6.3 cubic ft. capacity. Under the plate we found bits of insulation. We think that is what we smelt as it burnt up. He couldnt smell anything when he had it up to 400. So off he went thinking problem solved. Well, it still stinks. We will have Home Depot take it back. Oven takes forever to come to temp which we read in many complaints but thought thats minor. Dont know what oven to get instead since Whirlpool makes so many brand names. And other brands all seem to have their own problems.

I have never given anything a negative review before, but this, by far, the absolute worst appliance I’ve ever had in my entire life. I bought it because I had an old leaky washer, but I’d take it back in a heartbeat because it could ACTUALLY wash my clothes. We spent a lot of money on this washer because we wanted something really nice that would actually work, but this washer is no better than me throwing my clothes in the sink and turning the water on. I’ve tried every kind of detergent and pretreatment that I could possibly try, and nothing helped because the actual machine don’t do nothing. Shirts come out still coated in mud, and half the load is dry??? Please, save your money, get your washer somewhere else. And I hate to even give this thing 1 star because it ain’t even worth that.

I depend on my front loading Maytag washer. It is very reliable, does a great job of cleaning even difficult items like comforters and pillows as well as items deeply soiled. I use the many features like water temp and level, fabric type, heavy or light load, etc. The only complaint I have is that the front cover of the detergent, fabric softener and bleach drawer came off and the exterior paint on top of appliance is rusting and peeling. A stronger substance for the surface where often detergent, fabric softener and other substances are often stored and they leak.

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

The control board is not working on my 2 year old dishwasher. I now see this is a common problem with Maytag dishwashers. I have called to see if there is a recall on this problem and they said no. I have been told it can cost up to $500 to fix it so I guess it is a throwaway. I should have called when it was purchased as the digital buttons didnt seem right from new. What a waste of money and I will never buy Maytag or Whirlpool.

Maytag 765 Washer - What a disappointment after having a Maytag set for 2 decades only to get a new one that isnt worth much quality wise. 2 new washers in 2 weeks due to a ratcheting noise that they both have. The solution??? Have a third service call only to hear, replace it (which we did) or replace the transmission. The 3rd call coming up will be the same. What good is a new transmission going to fix it when the last 2 machines had New transmissions. Quality??? I dont think so. Oh, I had to buy the second replacement in order to get credit for the first one. This was at Lowes. Is there even a quality washer out there anymore?

We purchased a Maytag Dishwasher Model #MDBTT60AWW3. Shortly after manufacturer warranty ran out, the control panel went out. Luckily we had purchased the extended warranty. The repair company came out and put a new control panel in it. Two months later, the control panel goes out again. The warranty firm sends out a different repair company. They replace the control panel again. This time it doesnt work. They replace some of the buttons as according to the repair person they arent registering the correct OHM reading. It works again. Yay!. A week later, its not working again. The repair company is coming back. This is really starting to get old. Between the multiple times it has broken down, waiting for the repair company to come out, diagnose the problem and order parts, we have been without a dishwasher for approx. 2 months the multiple times it has broken down. Im so fed up with this thing. I also will never ever buy another Maytag again. They need to have a major recall on these because of the terrible, terrible control panel. This isnt just me, its a lot of people.

The Neptune Front Load Washing Machine I purchased in December of 2007 started sounding like a jet taking off, about three months ago. The noise has become unbearable. The repair person said that the whole drum needs to be replaced and it is not worth fixing. Are you kidding me? This was an expensive washing machine and now we have to get a new one? We cannot afford to get a new washing machine. We need an explanation of why this would happen and from the other complaints I have read on the Maytag website, we are not the only ones. This is the second time something has happened to this washer, the first time, it was under warranty (only a few months into the purchase and the pump was bad and was replaced). What is the company doing to help people with this faulty machine?

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

Very poor quality. Vegetables freeze at the back of the fridge I have tried everything. The vegetable drawer constantly comes off its track and the freezer door slide jams and stops the door from closing. It leaves about 1/2 inch gap. Now the Whirlpool/Maytag company changed their corporate policy and wont allow an appliance store that to come out and fix the fridge I have to go back to the manufacturer. Their website wouldnt take my email address when I tried to sign up for an account and they wont answer the phone. What a hassle. Ill buy another brand next time but never GE or Whirlpool again!

I have a Maytag Bravos washer and on almost every other load, the dark clothes (mainly slacks) come out with white splotches on them and then I have to re-wash the pants and the splotches go away. What could be causing this? Im tired of washing clothes more than once. Its incredibly wasteful and bad for our environment. Thank you.

Maytag Bravo XL - We bought the set about a year ago, after high recommendations from the salesman at Best Buy. This washer does not clean clothes - they come out with soap & spots & white stuff, even after I use the deep water or the extra rinse cycles. These cycles take well over an hour. When they are finally finished, my clothes are twisted into ropes that have to be unwound & taken apart before putting in the dryer. I hate to think what its doing to more delicate clothing, getting stretched & tied up like that. This washer is awful - cant wait to get a new one. The dryer isnt much better - cant believe a $900 dryer doesnt have a steam refresh cycle! And the controls are so touchy - if you actually push them, they dont work. If you lightly hover over the button & barely breathe on it, it does - very strange.

I bought a Maytag front loader washer and dryer, plus the pedestals for each. In last August of this year the washer just stopped in the middle of a wash cycle. I placed a call to the customer service. The tech diagnosed and placed an order for a part and set an appointment for two weeks later, with a time window 1 to 5 pm. The person called at 5:30 to tell me he had an job before he could get to me. I had taken the day off to wait for him. I called and they ended up rescheduling, for two more weeks.. Tech came ordered different parts, tech did not show up. Tech came out again ordered new parts. Next week he arrived wrong parts. Washer still not extracting. New tech, new parts, new appointment, this was what happened throughout September and October. Tech was not happy with his job, stated that to me, would not do anything but install part, even if it didnt work. He took parts with him. The washer still not extracting. Last Thursday he didnt even have all the parts, made the decision to replace machine without discussing it with me. Told me Sears would call me in 48 hours. Received call today Tuesday. Go to Sears to have it replaced. None of the machines they offered are compatible with mine. I will have to purchase the pedestal for the new machine, plus pay the overage to get the comparable machine. Service appointment people were horrible, cold and rude. Sear store at the mall where I purchased my washer said that it was not their problem. Once we sell it you are in their hands. Have had Maytag for over 30 years. Will never buy it again. Will never buy at Sears again. Too bad I have to replace my washer with something from Sears. Not enough space to write everything I have gone through, the lost workdays, the extra expense of having to go to the laundromat, the stress of dealing with incompetent people and techs.

Bought brand new. No deal, not on sale, not a return. Just heres money... give me working washer. This thing doesnt wash anything. It leaves soap all over the clothes. When you turn it on and wait til it starts washing, look in there with the lid open... theres barely any water! The clothes on top stay dry! The only way to wash your clothes in it is to add three-3 gallon buckets of water at the start of each STAGE of EACH cycle! My wife showed me after three months of washing clothes like this. Anyway, to the garbage with this and back to Whirlpool basics with me.

I wish I had researched high efficiency washers before buying because of a name we trusted implicitly. Our washer does not get our clothes clean & cleaning it with Affresh is not enough. I have never had to work so hard at getting clothes clean! Towels smell musty, stinky. My husbands sweaty workout & gardening clothes smell worse, even with subsequent washes & his shirts have white spots from the detergent not even being washed out. The rinse cycle water just washes out the bottom of the machine while the clothes are plastered against the side of the machine. I do not wash my husbands clothes with anyone elses or it all smells and if he washes them twice, they still have that odor that comes from being dank. Even if I stop the washer to arrange the clothes on the bottom so they will get rinsed properly (gotta wait two hours for a load to finish) I have bought every HE laundry detergent on the market, every odor remover, vinegar, baking soda, bleach. For a year Ive been chasing my tail to do the dance that I never had to do with a top loader agitator Maytag that we had for 7 years and never had to clean once, but used unscented detergent that got the worst smells and stains out without much thought. Even reviews that I read about their amended top loader with an agitator are not very good.

Wish it was a French door style instead of freezer on top. Not good if you are tall. Other than that we are pleased with it but will look to trade for a French door style.

Our Maytag oven (not sure model) in the first year started doing crazy things with the oven computer. The oven would shut off and come back on and the display would be garbled. Also when my girlfriend tried to pull the turkey out, the rack fell off the left side and dumped all the juices into the oven. She almost got burned and there was a lot of smoke. The freakin rack should never fall off! Also our dishwasher is on its second control board. I lived by Mr. Maytag and his airplanes/helicopters at Crest airpark in Covington, WA. I wish I still did. Id like to ask him what he thinks of his crappy products. You get nothing for your money anymore. Im not sure but Ill bet both of my problems with these products have something to do with saving a buck by making this crap in Mexico or some other *** hole. Im just glad Maytag doesnt make airplanes or medical equipment.

The Maytag Bravos XL Gas Dryer I purchased less than a year ago has stopped working three times. The dryer stops producing heat. I am now about to call Maytag repair again and waste time and energy setting up a warranty service call. I spent a lot of money in order to go to the Laundromat on a Sunday. Do not purchase this dryer if you would like to be able to dry clothes at home with any type of consistency or confidence. Arrrggg!

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

MER8700DH - Within 6 months, left rear burner stopped working and Maytag repaired it under warranty. Within next 6 months, and just before end of warranty, right front burner stopped working and again Maytag covered it under warranty. Within the second year of ownership, the oven was not working correctly and Maytag refused to cover it because it was off warranty. So I called a local appliance repair company who gave me an estimate of over $300 to repair it and basically advised against repair stating that this stove was a piece of junk. So I replaced it with a GE and junked the old one before it was even two years old. I filed a complaint with Maytag. At first they said they would go half on the labor, but then they said I should have bought the extended warranty and refused all further help.

Oh my god, I feel your pain, folks. My mother is sick in the hospital while I try to maintain my house with this totally POS refrigerator!! 3 defrost cycles to remove ice and now the service guy tells me that compressor is shot, 6 week back order for parts!!! Just two years old!!! Also had the same water overflow issue to boot 1 year after getting it. Maytag (whirlpool)- youre killing me!!!!

Bought a Maytag Washer & Dryer and after only 4 years the front panel went...cost to replace part only $653.55. After expressing concern about the price Maytag cut the cost of the part in half - now installed $475.00. Disposable dryer. Choked on it and decided to go ahead with the repair. Part was to be in in a week and it is now been a month. Maytag/Parts supplier no idea where the part is and doesnt return phone calls. Have to use the laundromat (family of 5). More money out of pocket. Not to mention time. Called Maytag again to complain about the service and having to pay more money out of pocket to use the laundromat. They basically told me, Too bad. Have used Maytag appliances over the years and always been satisfied but the company is clearly going downhill.

I purchased a Maytag Bravo xl washer & dryer for $1600 in May 2017. Sunday, the user interface panel went out in the washer. After an $85 diagnostic visit, we were told it would be $500 to repair and take an additional 5 days. My husband is recovering from major knee surgery so I was short on choices. I elected to purchase a new speed queen and will never purchase Maytag again. The 10 yr warranty tag on the front is useless!

2013 We purchased from Lowes Maytag washer and dryer front load stackable. We live in a house 1890. We have a closet that these units go into so we are restricted to what brand we can buy. WE read the reviews. People must lie or are paid to write good ones. Within a few weeks the washer was giving us trouble. The door latch was not closing properly and it would take up to 20-30 min. to get it to start. Called and they said the latch was stuck. Again started having problems on and off. Months went by and had another service call. Same issue. Fixed it again. 2014 again same problem. We have to order a new latch and some other part. They could not get the part. Called Maytag directly and they were back ordered. What does that tell you. This is a major problem so much so that no one anywhere had the parts. 6 wks to finally get it and got it fixed. But in the meantime, the dryer was not working correctly. The clothes were damp and lint was all over. It was like a steam bath. They came out and when they looked at the back of the dryer it was burnt. Now this is what upset me. He said it could have caught fire and burnt down our house. Nice. The dryer was shot. They said to fix it would cost more than it was worth. Our warranty gave us a new dryer. 3 wks later I have my washer and dryer back working. In the meantime we have spent more time at the laundromat than at home. Brand new washer and dryer and are going to the laundromat. We had the dryer 5 days before it stopped working. Brand new dryer. Called and got a service call. The spring on the start button was not correctly put in. Who inspects these products. This was not right from the factory. So they fix it. Said if it happened again they would need to replace the entire thing. I do not know what that means. That was Dec. End of Dec. the washing machine is not running through the cycle. It had weird display on the washer. Thought maybe it was overloaded. Had to cancel and drain and then hit drain and spin. This takes not only more time but more electricity. I put in 2 sheets and it did it again. Had a few loads that ran properly and again it started. Called for service. He comes out and the motor that runs the belt to spin and some circuit board is shot. They call 2 days later and say that no parts can be found anywhere. WTH! It is 18 mos old and already the parts are extinct. So the warranty company said it was not worth fixing. They are giving us a new washer.I remember the commercials about Maytag that the repairmen had nothing to do. Well I thought it was because they did not break down. No... they cannot find parts. This is unacceptable. We have to go through the inconvenience of them not working and schlepping to the laundromat baskets of clothes. In the winter this is not fun. We are retired. Have to walk down icy steps. I have a washer/dryer upstairs and I cannot use them. Dont work. Not just the aggravation of dealing with repairs but not getting parts available, then having to wait to get money back to order a new washer and dryer and then get the dryer and 5 days later it doesnt work. Now we have to wait 2 wks for a new washer. It better work. Have to buy the warranty over again on each product cause they fulfill it when they buy you a new product. So this costs us extra money. The money we pay at the laundromat. The cost of electricity every time we have to run the washer 3-4 times to get it to spin out the water so I can dry them.To say I am upset is an understatement. I was told by a rep at Lowes, well Maytag has about 3 lemons a yr and you just got all of them. That was their consolation to our problem. I think Maytag needs to inspect their product. Our house could have burnt down. It is not a matter of parts going bad but damn the stuff is not even 2 yrs old. And the dryer was 5 days old when it stopped working. WE had a Maytag dishwasher and it was installed brand new and did not work. It had a defect in it. I never got to wash one dish in it and it had to be repaired. So I am not happy with Maytag. You go on Facebook and tell your story and all the Maytag horror stories come out. You need to do something to save yourself. Your company name is going down the tubes. Thought you should know this.

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

DO NOT BUY Whirlpool Corp Appliances, ESPECIALLY MAYTAG. They do not stand behind the units they sell. We dropped $600 on this Commercial Grade wash machine (5.3 cu. ft. High-Efficiency White Top Load Washing Machine with Deep Clean Option, ENERGY STAR Model MVW7232HW) and paid to upgrade the lines to stainless steel. It died after 22 months, a bad seal leaked water internally, fried some components (no water ever leaked from the unit onto the floor) and despite there being a 10-year limited manufacturer warranty on parts sticker on the unit... the fine print says only the tub and motor are covered.There is no way we could have known the seal was leaking and it was not the result of misuse (overloading) or abuse. The parts to fix it are back-ordered months and cost more than a new unit after install. Glad I paid $150 to learn all this. It also did not wash great on most settings. Purchased at Home Depot, they refused to stand behind the product as well.

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

I have a Maytag MEDC200XW3 model. Good price reliable and rugged. It washes all the way from my delicates to my husbands heavy fire protective clothing with no problems. Holds lots of clothes with no issues either!