Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

I bought a new Maytag stove and it is less than two years old and the oven has already quit working. It only has a one year warranty and will cost about $200 to fix. I am very dissatisfied with what I thought was a good product.

Very disappointed with Maytag Bravos XL, four year old unit with bearings going out. Quoted $400 + for repair. With two in the house, wash demands are normal. Quality is questionable to have bearings & seal going out in four years. Also you cannot buy the bolt which holds the Washer Motor Rotor Cover on without buying the whole $130 assembly. Daughter has Whirlpool brand with same problem. Seems to me this is a problem Maytag/Whirlpool should address. My old unit (that I wish I still had), worked for 25 years. Would not recommend these machines.

Maytag is the worst dryer ever purchased. We bought it in 2019 and the heating element broke. When I contacted Maytag directly, they said, nothing they could do. Really?? A major part was defected and there was nothing they could do! Its very sad when a major company that you purchased from shuts you down with a defected piece in their dryer and they chose not to help out the consumer. Shameful! I will NEVER purchase another product from them again...

We purchased Bravos series Maytag washer and dryer. These are a match pair, the top loader, extra large capacity, very top of the line, $$$$$. The washer has already been replaced after many repairs, but the replacement new Maytag leaves a powdered gray residue on all the clothes because of the small amount of water it puts in the washer tub. Even on the deep water cycle, if I put in a blanket it will come out of the washer half dry where water has never reached it. This washer is the worst I have ever seen and cost top dollar. Maytag says nothing wrong but when I show them the powdered residue on the clothes they refuse to answer. This is the worst engineered washer ever, tangles the clothes terribly, does not clean the clothes and usually forces you to wash them twice to removed the soap residue left on them. I have tried every soap on the market, stacked clothing as Maytag suggested, tried various tricks Maytag has suggested, but nothing stops the grey soap residue. This washer cost almost a $1,000 for just the washer, it is a disaster. I have asked Maytag to refund my money but they refuse. If anyone else has their washer - we need to join in a class action lawsuit to force Whirlpool, maker of Maytag to replace this piece of garbage!!!

Called Maytag. Was part of 2005 recall with Neptune Maytag washer. We did not realize it and now Maytag will not do anything. Now having dryer issues with a cracked drum. Called and there was no resolution or attempt to resolve.

Maytag washer, top loader, Bravo series: We purchased Maytag washer and dryer 4 years ago. Last week, the washer started sounding like a 747 was landing in our laundry room. Maytag sent a service representative and informed us that the bearings were faulty and it would cost at least $800 to fix. It is appalling that a 4 year old appliance should fail like this. We will buy a different make and we will never buy any Maytag appliance again. This is such poor quality and worse service. Maytag would only offer a 30-40% off a washer, but only if we bought it directly from them. We can get a better offer from any local store. They also said we could get a discount on the part we need, but not the service. Do not, I repeat, do not buy Maytag anything. You will regret the purchase.

We bought this refrigerator one year & 3 months ago & we have had various issues that are now no longer covered under the warranty. The pantry drawer has a peg on the side that is plastic & broke off on the right side. Will have to replace the whole right side panel. One of the door handles is coming loose which should be an easy fix, but its just annoying that it happened at all. Now the control panel is reading OFF/OFF & isnt responding at all. Tried unplugging for 10 secs, then plug it back in, but no luck. I cannot find any info online regarding this issue, so we will have to call Maytag. Hopefully, there is an easy resolution to this problem & we wont have to buy a new motherboard.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

Whirlpool owns Maytag and it appears that selling poorly made products is now their focus. When I purchased this Maytag 30 Gemini double oven range, I thought I was buying a superior product. Now, I am on my 3rd repair. When would it fail, on Christmas Eve morning when I am trying to prepare dinner for 20 people who are coming for dinner party. I paid too much for this piece of junk. From now on, I am buying from the scratch and dent sale because there are no quality appliances manufactured today. Buy cheap and it wont irritate you so much because no one especially Whirlpool owned companies focus on quality.

Bought washer in 2010 from Sears. Told me the washer had a sensor to measure how much water it needs. Was told by service guy that was a blatant misrepresentation by the sales person. It only fills up with 8 of water. When I wash my white towels with normal dirt (dog paws), with HE detergent and bleach on various cycles, my towels come out tie-dyed with dirt. Totally dislike this machine.

I thought it was just my machine that sounded like an airplane taking off in my laundry room. Upon reading these reviews I see there is a real problem with this machine. My parents and grandparents trusted and swore by Maytag products. Maybe then, but certainly not now. Maytag for me stands for landfill. I have had 2 Maytag certified service companies come to repair my washer that is only 6 years old and its the same part both times which I am told by these service providers has been a problem and Maytag knows about it. But when I call Maytag all I get is some sound bite advising me there has been no recall and since I have an extended warranty I will have to take it up with them since that is who my contract is with. Of course they are only obligated to make a repair and cannot replace a defective unit. Of course not.Far be it for Maytag to step up and really stand behind the promises they are making all over our television channels with the new Maytag man. The top of the washer is also all rusted out around the soap, bleach, and softener openings. It is a poorly made machine with known issues by a manufacturer that I will never buy from again. Its a sad day that manufacturers are not held accountable for inferior products and even sadder that this Maytag manufacturer boasts its made in the USA for this machine. So is it back to China we go??? If you want America back you better support your product to your buyers.

I had the exact same experience as the Tampa person with my Maytag dishwasher (Model: MDBTT60AWW). It was not cleaning the dishes, even when I thoroughly rinsed them. Plus, it started leaking midway through the cycle. Since the warranty was expired, I purchased an extended warranty in July 2012 for $296 (yes, in hindsight, I should have just bought a new appliance, not Maytag). I had 3 visits from 2 different technicians, both telling me the dishwasher did not leak. One telling me I was using the wrong kind of detergent and thats why dishes werent getting cleaned. The other telling me that there were too much suds and that could cause it to leak. So, I should pour a tablespoon of cooking oil (yes, cooking oil) in the dishwasher when it starts leaking and that will cut down the suds. I dont think so!Then, I found out a couple of weeks ago that this model was under a recall since 2010, not related to the leak at all. Yet, Maytag still sold me the extended warranty (wheres the ethics of that?). I requested a pro-rated refund of the balance on the warranty - and wouldnt you know that with the technicians service calls, the amount of time used on the warranty (6 months) plus an admin fee - I have used $296.48 of the warranty amount. It is almost to the exact penny of what I originally paid, so I will not be receiving any refund. They are only giving me a debit card of $150 or $250 once I buy a new Maytag to replace the recalled model. I do not want to continue down this frustrating path known as Maytag appliances.

My husband and I were Maytag fans, and we purchased the fourth set of Maytag w/d in May 2019, along with an extended warranty. Four sets may seem like a lot, but my husband and I have been married for almost 30 years now. Long story short, the washer went haywire, and kept flashing LF. After searching Google for answers, my husband flipped the main breaker, then unplugged the washer overnight. It seemed like that fixed the problem, but it didnt. I called Lowes for help and got hung up on numerous times. The hang-ups were not due to my attitude or choice of words. I kept getting transferred from person to person and put on hold, then the phone would go dead. Eventually, someone actually spoke to me and gave me an 800 Maytag number to call, which resulted in more hang-ups.As before, eventually I got to speak to a real human being who took my info and said that a service tech would contact me. Well, over two weeks later, no one has contacted me. However, due to my post/review on the Maytag website, a Lowes representative did call me and offered me a full refund on the washer, but not a word was mentioned about the dryer that seems to be possessed because it turns on and off at will. My husband and I have a limited income, and we purchased the top-of-the-line Maytag w/d thinking that it would last at least ten or more years.For the money that we spent, the w/d should have at least lasted for the warranty period. As noted before, Maytag was once the Toyota of w/d. You could not purchase a better product. Now, the exact opposite is true. Buyer beware, the most expensive with all of the bells and whistles is not always the best. My husband and I have gone retro with the purchase of a new Speed Queen w/d, which will be delivered this week. Hopefully, it will live up to the reviews that I have read.

Maytag Bravos washer and dryer both need replaced in 3.5 years! Control board had to be replaced on washer in under 2 years and now the replacement went bad in about 15 months. Maytag can’t help! Hundreds of dollars wasted. Dryer is not much better as the control board is now malfunctioning! DO NOT PURCHASE MAYTAG!

Please do not buy a Maytag washer top loader. It does not get enough water and it does not clean your clothes. It is the noisiest cheapest made machine out there. If you have kids you really need to bypass this one. I have had this for 10 months and its only me. Please especially if you have children stay away from it. Im the most unhappiest camper Maytag ever had.

We purchased a Maytag MDB7749SBWO Maytag dishwasher. Suddenly the control panel does not work. Trying to find out why I found that there are thousands of complaints about this known defect with water and steam getting in and corroding the control panel. Shame on Maytag for continuing to sell these without fixing the problem. I expected my dishwasher to last many years based on the Maytag reputation instead I need to replace it. I am not going to spend the money on a repair with a machine that will have the same problem again according to other consumers.

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

Got woken up to the sound of my refrigerator ice lid flapping. Boy is it loud! Called Maytag and found out it was a recall so they will fix. They set up for someone to come out to fix the following week. That was a flop because they did not have the part. I waited 4 hours for someone to show to find out that Maytag scheduled the appointment for nothing - not only did they NOT have the part but they did not have a clue as to when it will come in. Time is valuable! Here we are 5 weeks later and my refrigerator is still flapping and loud. Has been calling Maytag for them to say that the part has been expedited. Well it has been expedited for more than 3 weeks now! Today they say that it will be another month before the part comes in! Not Good! This is such an inconvenience and Ive lost a lot of sleep over this flapping noise. Its an embarrassment when guests come over to our home! Tired of it!

Horrible machine. Uses too little water, cycles are too long. No matter what the size of the load, it takes an hour. Just after 3 years the bearing went out on the machine. Cost for repair will be $250. Thats not even an electronic problem which Im sure would be next. NO THANKS. Im getting a new machine and it wont be a Maytag.

Chalk up another bad tub bearing. Washer around 4 years old. Repair man says $350 to $400 to fix. Also said sees it couple times a week. Said after Whirlpool bought Maytag quality nose dived. Maytag no longer top of line. Will never buy another Whirlpool or Maytag product. Just replaced control panel on dishwasher also. Amazon sells kit to repair washer. That should tell you how bad it is. Called Whirlpool to see if they had plans to do anything about this. No they dont. Stay away.

Maytag Centurian is a terrible product. I dont think the designers of this model have ever washed and dried a load of clothes. Washer problems: The lid (top loading) locks so user unable to determine if the correct amount of detergent is being used. There is an unlock button, but it takes quite a long time to unlock (maybe 15 seconds), then an even longer time (seems like a minute or 2 to restart). The machine is LOUD and at one point in the cycle BANGS. I actually returned the first as defective, but when the 2nd machine made the same noise, I was told, no, thats the way it is. It seems to take much longer to wash a load than my previous machine. The Power Wash tears my clothes. Even the regular wash puts holes in my thin tee shirts after a few washes. Really had to get spots out. I almost have to hand wash to get the spots out BEFORE putting in the machine. Dryer Problems: Takes 70 minutes or more to dry a normal load with a couple of towels. The cover to the lint catcher doesnt seem to be properly sealed. Lint particles get all over the top of my dryer. I bought this Washer/Dryer combo last year. Im annoyed every time I do laundry.

I bought a Maytag microwave model mmv4203ds00 on May 2010. On 8-20-10, the microwave stopped working. It was serviced under warranty. However, on 10-31-11, the microwave stopped working again.

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

I purchased range in January of 2011. I have had the top replaced and still it looks bad. Every time I use a burner, even if boiling water, I need to use the razor scraper to clean the burner. I’m very dissatisfied. We used to say we would buy nothing but Maytag but not anymore. Tell anyone who will listen how much I hate this stove. Oven does not cook properly, burns most everything I bake no matter if I lower the temp and time!

First front loader washer and love it. Saving on water, less tangling of clothes. So far they are quieter than others that I have had. The dryer is almost 10 years old and the washer less than a year. The machine I had previous to this was top loader that had to be replaced, would no longer spin.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

Maytag will not fix 2 major issues with new $700 Maytag dryer bought from Home Depot who takes no responsibility. They wont return it. Maytag wont replace defective dryer unless technician from totem appliances cannot fix problem. The tech ordered a control board and timer. Only installed the timer. He did not fix 2 issues. Dryer never stops at OFF. Dryer leaves damp spots on any clothing whether small or medium large load. Was told by Maytag if damp spots then its OUR problem... our ventilation. No it is your sensor. Our model is ymedc465hwo serial m820. 07331. Bought in late Oct. 2018. Two supervisors later we are being sent to tech or tech company and played games with. All I know is Maytag sells defective dryers then wont replace them or fix main issue.

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

My husband and I purchased a Maytag stainless steel French door/freezer bottom ice making fridge from Hhgregg in Brown Deer, WI and 8 months later (now), Ive been told that my food that is spoiled, cant be replaced and my service for the fridge wont be done until next week! I have 5 kids and a husband. This has turned our world upside down. I called them and spoke to a Nicole and she said they cant do anything for us, but we can try to contact the diamond repair service at 269-927-2519 to see if they can get us in sooner. I asked for a refund for the fridge and she said no, the 10 warranty only counts for repairs... I am so angry that I didnt research Maytag before now. I gave the Whirlpool fridge to the delivery guys of Hhgregg and I had that for 18 years and it never went out on me. If anyone is reading this and is upset as well, let us get together and start a class action suit!

Have had nothing but trouble with this fridge! Ice forms at bottom of freezer with frost all over top shelf. Ice maker no longer works. 3 years old for goodness sake. Had repairman replaced all lines, and still have the problem. Heard you have to unplug fridge for 24 hours to solve problem EVERY 2 Months! I Guess the Maytag repairman stays lonely because they dont stand behind their product! Hate it!!

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

Neptune washer maxima XL steam - Our machine is only 2 years old and we feel the soap dispenser is defective. That little door inside to choose either liquid or powder is not flush with the basic cup and to make matter worse, there is a V shape hole at the bottom of that little door. Meaning, fill it up, and while you are looking for the softener in your closet, all the expensive liquid HE soap is on your floor! And when you close the door, if you wait for starting the load, all the soap goes into that rubber gulley instead of being sent over the clothes. I just got off the phone with them, they wanted to send a technician AT MY EXPENSE - when I do feel it is a deign mistake, not a use/abuse on my part. I proposed instead to send them a picture. They refused. I proposed to send them the soap drawer, they refused as well. I will never buy Maytag ever again and dont recommend to anyone to go to this Brand name!

Same issue as everyone else. After about 15 months the control panel on my Maytag dishwasher model#MDBH979SAM1 has malfunctioned. First it would only let me choose the rinse option but now all the lights are turning on and the dishwasher will not stop washing but yet the dishes are still dirty. I called Maytag and they quoted me 249.00 to fix the issue. But if its a common problem with this make and model why do I have to pay to replace the panel. They should recall this model or replace the panel with an updated one that wont have the same issues! I cant imagine paying 249.99 every year to replace this panel that seems to malfunction no matter what you do!!! I paid around 550.00 at the home Depot for this dishwasher! It did not even last me two years!!! I want a lawsuit filed against this company and I want my money back or my dishwasher replaced with one that works and wont have the same issues!!!

Maytag 2000 front loading washer - This unit was purchased in Feb 2013 along with the matching dryer. From the onset it has presented with the problem of trapping small objects such as socks, underwear and other small loose objects in the rubber seal at the front of the door leaving them soaking wet and needed to be wrung out by hand. There is not any way to run a second spin only to wring out the clothes without doing an entire wash or rinse again rendering the efficiency void. I have been able to buy a mesh bag to put smaller items in for washing with the regular laundry load. However, this is not why I purchased the washer and I would strongly recommend to others not to buy this product. Very disappointed. I thought the Maytag brand was reliable. Never again will I buy any of their products.

M1BXXLZYB00 - This is the worst appliance I have ever owned and I am 56 years old. Very noisy, freezes my produce and actually anything in the refrigerator. Yet the freezer wont freeze popsicles. Had 2 service calls on the fan and or fan motor in the first 6 months. Now 2 years later we have replaced 2 compressors and had to pay 200.00 labor to have installed. Now the compressor is out again not even 30 days after the first 2. Whirlpool wants to send another compressor and the poor repair guys are suppose to do it for free now because it is within the 30days. The offered me to buy another refrigerator with prices of 699.00 and 519.00. My fridge in the garage is way more dependable than this one and I have had for 10 plus years with no problem.

Maytag top loader washer will not complete cycles. Washer is only fourteen months old. Repairman says parts will cost four hundred and seventy four dollars - almost what I paid for the washer.

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

The glass shelves stop 2 1/2 inches from the back of the refrigerator. Things keep falling down in back. I have a counter depth. Cant afford to lose any space. Freezer poorly designed for space compared to one I had before.

Bravos XL Like so many others Ive read, this is a terrible product. Washer constantly goes off on unbalanced load. After 14 months, the plastic tub disintegrated. Maytag tried to sell me the service and extend a warranty for $300 also. Just like all the other reviews. Wow, has Maytag gone downhill.

My Maytag (MER7662XQ) oven has stopped working after barely 6 months of use. I filed a warranty-repair complaint and reported the error codes shown: F1 (faulty touchpad) and F3 (faulty temp sensor). Although Maytag promptly sent a repairman, he arrived without parts and left within 5 minutes without fixing anything. He said he would order parts. Whenever they were delivered to us, by mail, we should call again to schedule another repair. But he warned he was prohibited from coming out for another 7 days. So far, Ive been without an oven for almost 3 weeks and there has been no action or information. My calls to Maytag produced nothing, except confirmation they show the repair as open since they do not actually distribute parts, and the repairman is with an outside company. A terrible product and a worse service! I would not ever buy another Maytag product and recommend that no one else does either.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

Well, I thought I was buying quality products dishwasher and refrigerator and both are very disappointing. Of course the Maytag dishwasher (MBD7749AWB2) really upsets me since I just bought it in Aug of 2011. Now it will not finish a load of dishes and I did what the lady at Maytag told me. She said it was the control board. But it is not the control board. It is still working the same as it was. Now what should I do? When they said I had a 10year warranty I didnt think a known product like Maytag would let me down. MAYTAG, YOU SHOULD BE ASHAMED TO ADVERTISE YOUR PRODUCTS TO LASTS! THEY SUCK!

I purchased two Maytag appliances; PC-touch control 500 Electric Smoothtop and a dishwasher. In less than two years, I have spent over $1,000.00 repairing these two appliances. With my stove, I have replaced the PC control board and the oven light kit. Less than a year and a half, I now need to replace the PC control board again. I have been a Maytag customer since 1976. The dishwasher had a recall for the heat element and I replaced the control panel control board and door lock switch and the main control board. I will never buy Maytag again.

Maytag 18.5 cu ft Bottom Freezer Refrigerator purchased 12/10/12. 1/12/16 the bottom of the freezer had an inch of ice that leaked onto the floor. My plumber chipped away ice and unclogged drains $97.50. 4/19/18) the same $97.50. 5/22/18 an appliance repair business installed a drain kit $148.40. This was his 25th Maytag with the same problem. A whole website has complaints about this problem. I sent a letter to Maytag and they wanted to send out their technician to find out the problem (with a service cost to me). With all these complaints, and a kit to fix it, they already know the problem but refuse to do anything about it. Maytag used to be a reputable company. No more. The customer service said I should have bought an extended warranty. I said a $1400 refrigerator should last longer than 3 years (the first leaking occurrence). I will never buy a Maytag product (nor Whirlpool that makes it).

After only about a year or so - and it is out of warranty - the clothes are not clean - there are white type of scum marks left on clothes and especially dark clothes. This is even after I use the recommended detergent and less than normal and do a double rinse. Have to wash clothes again with no detergent with a double rinse again. Just so annoying. Would never buy Maytag again.

Purchased a Maytag dishwasher 1 1/2 years ago and the panel went out. I paid $550.00 for this item, wanted to get a nicer one hoping it would last. Of course they only have a year guarantee for parts and Labor. Will not buy another Maytag appliance again!!!

Bought a Maytag Stainless Steel kitchen stove to upgrade my appliance before retirement. 14 months later the spring loaded hinge failed. A bad piece of engineering in the way of a retainer pin to hold the spring pressure tore out of its pressed metal hole. The hollow pin was fastened in place by a 3 fluted punch instead of with a proper rivet with a head. My local parts supplier had 10 on hand so you know they are aware of this. $70 and an hours labor and it is repaired. My local seller said, Too bad you didnt get the extended warranty. So much for Maytag dependability.

Same thing as everyone else. The motherboard/control board, the main face of the washer went out and this part isnt covered on an $800 commercial washer after only 3 years of residential use on a commercial washer. Menards refused to swap it out, saying this is Maytags issue. Maytag boasts their 10 year warranty and labels it right on the motherboard as a 10 year warranty, but the motherboard isnt covered? If the main computer isnt covered, What is covered? Just screws? I called Menards and got nowhere. Called Maytag and held for an hour then had to hang up so I can work. The warranty is extremely misleading and is the reason we bought this particular washer, because it says 10 year parts warranty right there, but Maytag conveniently doesnt consider the main control board a part.

I have had a number of Maytag washing machines in my life and have never disliked a machine as much as the last one I purchased! The bleach dispenser is awful and any bleach that happens to land on the outer rim has ruined many clothes. I took them to my dealer to show him the ruined clothes and was told bleach does not evaporate do must be wiped off each time. With no soap dispenser I find I have to put the soap in first and keep trying to fill the machine some before I add the clothes. This takes forever but if dont do this my clothes are stained. I purchased this machine on April 11, 2017 and can not afford to go buy another washer at this time. The Dealer can not help me and when I called Maytag they were not interested! Buyer beware!

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

We moved into a new house and the GE washer died after the first week, then the Whirlpool replacement died after two weeks. Decided to try the Maytag which the store gave us for $50 more than the Whirlpool. It runs like a champ. At least two loads of laundry a day every day and sometimes weekends. Clothes come out perfect, no damage and the machine is quiet.

I purchased this washer three years ago. It worked fine, but all of a sudden the washer stopped spinning and was not following any of the cycles. Of course it was out of warranty. The repairman states the computer board on the washer is fried and will cost $400 to replace. Several stores have stopped selling Maytag because of quality issues. No more Maytag for me.

Purchased Maytag MDBH979AWW serial #FY4202009 from Lowes October 30, 2009. Control panel went out after warranty, and we replaced it. It quit working again in May 2012, and we replace the control panel, and then in November 2013 it quit and we replaced the control panel along with a new door latch just to be sure on December 4, 2013. The dishwasher quit working mid-cycle a couple of weeks ago only 9.5 months since we replaced the last control panel. Im fairly certain it is the control panel again. We have paid more to replace control panels for this dishwasher than we paid for the original appliance. There should be a recall and compensation on this issue. Very disappointed that Maytag and Whirlpool do not resolve this issue. We will be buying a different dishwasher, and it will not be Maytag or Whirlpool.

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

I purchased a Maytag Centennial washer and dryer on February 4th. It was delivered on the 11th. I am dissatisfied with the performance of the washer. I use the same amount of detergent and fabric softener as I did for my 15-year old Maytag washer, but the wash is not as soft as with the old machine. Also, the wash when finished appears to be a lot wetter. What is wrong? What else can I do?

We purchased a Maytag front load washer and matching dryer in 2007. In 2010, the main control board of the washer broke down. We spent $450 to replace it.In 2014, the washer stopped working. The dryer started producing horrid odor when we used it. We replaced both with LG recently. We NEVER buy or recommend Maytag products. Stay away from Maytag. There are many other reliable washers and dryers in the market. This is to help other consumers.

Never liked this machine. No flexibility in settings, ruins clothes, noisy and often shuts down. But main concern in the fact the whole top is rusting by the bleach dispenser and it leaks from the top all over. It is only 3 or 4 years old. Can not believe an expensive product like this can be so bad.

We purchased a French door Maytag refrigerator model MFD2561HEB in November 2007. In August 2008, the unit stopped working suddenly. The high voltage control board was replaced under warranty, but the tech could not determine why the board failed. I called Maytag to demand a new refrigerator. The best they would do was to extend the warranty for 6 months, no charge. The unit quit twice more in September. A tech was summoned (paid service call), nothing found. It started working again. Since then, the thing has quit several times. We unplug, move all food to a second refrigerator, wait a day, plug it in, and move the food back. The useless box quit completely this week, not quite 5 years of service life. The tech said the board must be replaced again, no guarantee. We declined. I called Maytag again to demand a new replacement and escalated the complaint. They are to call back, ha! In the 5 years of poor service (and poor customer service) from Maytag, the 30-year old second refrigerator has been up to the task of preserving our food. This experience has made me vow never to do business with a Whirlpool-affiliated brand again.

We have had our Maytag dishwasher MDB9100AWQ only 5 years and now it keeps shutting off. I see there is plenty of this complaint. I will not purchase another Maytag product after reading all these reviews and experiencing it.

I spent a lot of money for top-of-the-line Maytag. It sanitized and worked to perfection. Delay wash, force wash, grinds everything you could possibly ever want. Fantastic and I can move the racks around. Beautiful. Stainless steel tub. Stainless outside. It has a ribbon cord in the controller. They didnt seal the controller head enough. So the dishwasher stops working after an almost guaranteed 2 yards from the ribbon cord rusting. Well you got to buy another one and it comes as a fill unit at 250 IF you replace it yourself. About 500 for a plumber. And you replace it every 2 years. Maytag is having class actions about it, it knew it has the problem. Its just very profitable to continue having the problem.

Maytag Dishwasher Model # MDB7809AWB2. Part = Console Keypad. We have lived in this home for approximately 4 1/2 years. We purchased a Maytag Dishwasher and had to replace the motherboard in it about 2 months after the warranty ran out. We paid 1/4 of the cost of the dishwasher to get it fixed and I am having the same problem again. I am very dissatisfied with the appliance and I will not pay another $200 to get it fixed. I will never buy another Maytag appliance. Dont buy Maytag!!!

I purchased this oven about 6 months ago. This is my second Maytag oven which I had for 18 years. I am extremely disappointed in the quality of this oven. I did my homework and shopped around and chose another Maytag. First, the ignitor clicks and clicks but doesnt ignite. After 4-5 times I have to shut the oven off and restart it. But worse than that is the enamel on top. The quality is HORRIBLE. You cannot use anything but a soapy sponge to clean the top. With my last oven I was able to use anything (softscrub, ajax, the scrubber side of a sponge) and the top was shiny clean. My stove top is covered with scratches and is not even thoroughly clean. There are grease spots around the burners that if I scrub any harder Ill take the enamel off completely. Very, very poor quality. Will never buy another Maytag.

I would not purchase a Maytag in the future. The top oven does not work, and one of the burners is semi functional. Considering I have only have the oven about 5 years. I am not happy with the the product. In the future I would seek other options, Maytag is not on the list of products for consideration.

Maytag Bravo Quiet Series 300 MVB700VQ - My wife and I feel this is one of the worst machines sold. We purchased it from Costco 2 yrs ago and had several issues over the years. Pump, locking, water level, small clothing items like socks getting in behind the drum and clogging the pump, and yesterday a flooding issue. That is right, my Bravo 300 did not shut off and the water ran continually with an LD code displayed. The water overflowed into the kitchen & pantry. The wood floors are now warped. We were home so we were able to shut off the water as the washer controls (buttons) were locked and not responding. We spent the better part of 3 hours moving items and wet vacuuming the house. We now have a dehumidifier running in hopes we can salvage the wood floors and minimize mold growth.I will note that I have a home warranty (third party) that covers repairs on my appliances, this washer included. The repair man thought it may be the pump, a line, and/or the control panel/module that need replacing. The repairs would be covered by home warranty.... but not the floors. There is NO WAY I am fixing any washer that flooded my home.Yesterday, I took a 3 yr old washer with known issues back to Costco. I was not happy with the manufacturers suggestions that I buy parts as it was Out of warranty. Again, I had a third party warranty so the repairs would have been covered! It is clear that the manufacturer doesnt CARE about the quality or the performance of this machine. I have found a FIX for these issues. We are buying an LG Washer that is more $ and is highly rated by Consumer Reports. Stay AWAY from this model and current repackaged models of Bravo/Cabrio!

Same as all the other reviews control panel intermittently started to fail. Dishwasher is less than 3 years old. Does not work at all now. I tried resetting circuit breaker - nothing. This unit was $700 from Home Depot. Complete trash. It is cheaper to buy new dishwasher than repair - how unfair! Maytag won’t repair - well for over $300 they will. I feel better knowing everyone has same issue & is not my electrical system. Class action lawsuit!

In May 2007, I bought a matching Maytag Neptune washer Model MAH5500 and dryer. I also bought the 3-year extended warranty. Approximately 4 years later, actually 1 month after the warranty had expired, the washer started to get very loud and sounded like a jet engine taking off. I called Brennen Repair Service in Midland, Michigan. The repair man came out and said he did not even have to look at the washer. He knew what was wrong. The bearings were going in the machine. He said I could fix it for approximately $600 or just run it till it quits. I was furious. I called Maytag and explained my issue and was told that there was not a recall and they could do nothing to help me. They even told me that they had not had any complaints of this nature regarding this model. I told them they were full of it. I know of at least 4 people in my family and workplace that have had to replace the Maytag front loader piece of ** washing machine. I think Maytag should stick behind their product with all the complaints out there. I would like to shove my washer through their front window. I previously owned a Maytag washer for 25 years and had not one issue. It ran perfectly. I will never buy another Maytag product nor will anyone in my family. Maytag, you suck. Your service and reputation is appalling.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

I bought this washer three years ago. It is the worst washer I have ever owned. Washing a load of clothes, it goes off balance constantly, large load, small load...it doesnt matter. The smell because of low water usage is awful, and the clothes dont come out clean. I have to buy a new one and that really stinks. Maytag youre off my list for purchases. These days its quality that will keep you in business. We are too smart for this garbage.

Purchased Bravos 300 quiet series wash and dryer 3 1/2 yrs ago new. 18 months ago the washer gives me f51 and ul codes. To repair this USA made washer will cost over 250 dollars. I see why the Maytag repairman is not busy. Cause after 2 years you gotta buy a new one. All these digital controls are made in China - junk. Ill buy LG or Samsung next.

I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

Spent a lot of money on a Samsung washer. Will never buy that brand again. Too much money for only working for 2 years. And left clothes dirty. Had to wash clothes twice. My Maytag washer was bought with a deep water wash cycle. Totally love it. Also not a front loader.

We got our Maytag dishwasher in 2011. Weve experienced a lot of the same problems other people have mentioned. Control Panel was the first thing to go out. Now it has a foul odor coming from it and it doesnt get the dishes clean. The heating coil has stopped working and is rusting. This dishwasher is junk and Im very disappointed. I will never buy Maytag again nor any company related to them.

Every day you hear a hissing noise and water leaks in from the vents and freezes. This builds up and water leaks on the floor. You have to chip the ice out or end up slipping and falling. This happened to me - Maytag was no help. Time for a lawsuit.

I bought the power wash Bravos XL... Bad. It does not rinse the clothes, leaves residue on dark clothes.. probably all clothes - cant tell on lighter colors. I dont recommend!!! Waste of money.

This machine(Bravos XL Washing Machine) was highly recommended to me at the Home Depot by a sales associate. I broke down and took the recommendation. Oh how I regret that! This is a terrible washing machine. It does not put enough water into the machine to even cover the clothes halfway. It ties the clothes in knots! I made a terrible mistake when I purchased this!

I bought my Maytag Quiet Series 300 about 6 or 7 years ago. About January this year the clean light quit working but the dishwasher was still doing its job. Every once in a while the clean light would come on again and then go away. I did not worry about this as the dishwasher was still working despite the absent clean light. I did call Maytag and told them about this. I believe I even asked if they (customer service rep.) had heard about this and was told no. Last Friday the start button no longer works which means the dishwasher will not function. Some of the other lights/buttons work but not start or clean. I have dealt with Maytag repair service/customer service before about my Maytag washer. I know they are not much help and I always end up paying a lot of money. I am not interested in calling a Maytag repair person in and paying from what 300.00 to 400.00 dollars to get it fixed. Past experience of others seem to prove that it will break down again. Last Maytag appliance that I will ever buy. I used to be a loyal customer. I want to join the class action suit. Please tell me how I can join.

We got our Maytag fridge approx.18 months ago. There was no trouble the first year and there has been nothing but trouble for the last five months. The freezer started frosting one day which causes temp to get in danger zone - we defrost it with a hair dryer about every week and it has continued to frost up ever since. We have a friend that works for a certified Maytag repair business. He came to our rescue five times and called Maytag hot line for help.Together, they could only suggest that the gasket be replaced. He could not see anything wrong with it but we changed it just in case. Still, the problem continues. When we called Maytag customer service (877-556-57420), we were told that no one has had the problem before us. We just looked online; there are 521 complaints about Maytag. My question now is, how do we get a class action lawsuit going?

Having had a household for over 40 years we have had a few washers come and go. I hate to say it but this line of washers should go. Worst pile of junk parts I have seen. Bought it from Costco a few years ago based on past histories of Maytags. Was I ever so wrong. It has never worked well. I chalked it up to being Water Efficient but after reading over 8 pages of scornful reviews, I was mistaken. Water level is always too low to do anything so clothes are needing rewashed. Have reverted to using the Bulky setting to do general washing as that fills the tub about 1/4 of the way. Then the spin cycles stops due to unbalanced load and loud banging of the wash drum, EVERY LOAD!!! And now for the past month Code DL pops up saying it is taking too long to drain. I have checked all hoses for blockages, none seen. And with the glass top, you can SEE the washer NOT WORKING right. We have a door on the laundry room and even with it closed the volume is over 70 dB and can overpower most conversations in our family room 20 feet away. I have been told that Costco may take it back but why punish Costco members for a design failure of Maytag??? Has anyone thought about a Class Action Lawsuit? The Bravos Quiet Series 400 dryer match to this washer has so far been flawless. I may have to dig the 20 year old Whirlpool washer out of the storage shed to replace this Maytag. Sad. I want to state my true feelings but I will not use profanity here.

I moved into my home in July 2013. My kitchen came with all stainless appliances that appeared and seemed to be in excellent shape. I have been using the Whirlpool Microwave oven to heat foods (all in microwave safe) containers and dishes. This morning, I was heating a muffin, when suddenly I hear popping. When I looked through the glass into the inside of the microwave I saw sparks then flames. I immediately stopped the microwave. The fire apparently started in the area of one clip that holds the metal rack inside. In researching this issue online, I found hundreds of complaints from people who have experienced the same issue, and Whirlpool refused to replace the unit because it is out of warranty.

Bought this because it’s American made. It seems to be very glitchy. If you don’t use the detergent drawer it always flashes low detergent. The quick wash leaves soap on clothes. It acts up and leaves clothes too wet. No buzzer to tell you when it’s done. Have to hold button for 3 seconds to start. You can’t just hit button and walk away. Then wait for it to sense the load first to make sure it starts. Very expensive model.

This washing machine just sprinkles water on your clothes then ties them up in knots. And to add insult to injury, needs repairing every year or so. Horrible! It does have a couple of redeeming qualities, but they definitely dont outweigh the cons. It spins the clothes quite dry and has a large capacity. I have dogs and kids who play football and a husband who does construction, and its not unusual to find lumps of dirt and fur trapped in an article of clothing or blanket. All my bras and sweaters get ruined, it twists them up horribly. The blankets and sheets end up in a mushroom shape. Sad to say, NOT good. I like Maytag, but not BRAVOS.

I have a top loader Maytag washing machine, Model MVWB835DW4, bought in 11/2019. Five months of light use, the lid cracked. Received a replacement and four months later the lid once again cracked in the exact same spot. Requested replacement parts under warranty and I was told that a service tech must install the lid. Due to health and safety concerns related to Covid, we are not take any chances letting people into our home. My wife and I are 70 years old and are at high risk. Maytags response was they would not send parts under warranty to me and a service tech must install the parts. If I dont let them in by 11/2/2020 (the end of the warranty period) then I would have to pay for the parts. Maytag has the very worse customer service in the industry.

My Maytag washing machine is rusting out at less than three years! [Photos included]. I have called customer service twice, spoken to two different women and have been told that it is a cosmetic issue [Model MTW2541240; Serial CW2541240 ]. The last e-mail with photos was sent to Gwendolyn **. I indicated that the rust has ruined very expensive sheets, other clothing, towels. It took me a long time to figure out what was causing the spots on the clothes. There is rust on the outside of the machine, the lid and inside the actual drum which holds the water. The machine is a lemon. You have me registered in your system with the date of purchase.My question to you, since when is rust in the inside of a washing machine a cosmetic issue? Are you aware of this issue? Do you as the CEO believe this is what is acceptable for a Maytag washing machine? I firmly suspect this issue is beyond my washer based on my research with various stores and sales people. They are telling me I am not the first with this issue, non-Lowes stores. I purchased the machine at Lowes and because no one at Whirlpool was responsive to him or to Lowes, he is offering to apply the refund to a new Lowes washing machine. I am now in the process of searching my credit card records from Sept-Oct 2008 which is when I bought the machine.I would like not to be restricted to Lowes for another washing machine. I will notify Rick ** (at the Lowes Turtle Creek, Coconut Creek store in Florida, telephone 954 346-3993) of this letter to you so that you and Rick dont think I am trying to obtain a double refund. I just want the full value of the washer back so that I will have a choice in the replacement. The selection at Lowes is limiting. I will upgrade to more of a commercial washer and pay the difference. I wanted you to be made aware of this issue.

We purchased this washer from Sears. Its always been loud during spin, but the past couple months it has gotten VERY loud. It jumps around. Also, it tends to ball clothing and towels. It has been hard on my clothes and bedding. Many times I have to rewash towels and bedding, even jeans at times. I have been very unhappy with this purchase from day 1. It was not a cheap washer.

I have a Maytag Series 3000 washing machine which, as many knows, is the same as a Kenmore. I bought the set 23 months ago and since then, I have had nothing but trouble. In my first three months of ownership, I had my first error code of which I had to replace the hot/cold water valve. Fortunately, the unit was under warranty. Since then, I have had to replace the CCU and MCU twice. Now, the units MCU went out again! Whatever happened to the Maytag name? How can I get this permanently fixed or replaced? Is there a lemon law for appliances? Any assistance would be appreciated.

Purchased a Maytag dishwasher from Best Buy. We did not buy the extended warranty from BB because there is a warranty with Maytag. After 4 months of use the washer stopped working. We were unable to return it to Best Buy because we exceeded the 2 week return policy and needed to rely on Maytags 1 year warranty. It took over 2 weeks to schedule a repair and he was unable to fix it, it needed an entirely new Control Board and UI panel. 3 weeks later he returned with the new parts. It worked for 10 days with the NEW Board and panel, it has now stopped working again. We are not able to replace it due to the California Lemon Law which allows a company 3 opportunities to fix it before replacing. Next time I will purchase the Best Buy warranty so I can replace this Maytag LEMON.

Purchased dishwasher from Highway Appliance in Dunlevy, PA on August 21, 2013. In August, 2015 control panel apparently went bad. When pushing normal, other buttons light up, but not the one you select. Tried throwing the breaker to reset, to no avail. Based on reviews, seems like many others have the same problem. Step up and do the right thing Maytag - recall & replace these machines!!!

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

I bought a Maytag washer 6 years ago. Energy saver. Less water. Nothing ever seemed clean. Always white streaks and I used liquid detergent. So we went out and bought another Maytag with agitator June 2017. Never drains properly. I will never ever buy another Maytag product.

First bought a nice looking Samsung. Didn’t last 6 months. Upgraded to a nice Maytag with steam and have never regretted it. It’s been years of worry free and trouble free use. My Samsung dryer is on the way out the door and to be replaced with a Maytag too.

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

I had this microwave less than a year. The control panel went out and Maytag fixed it. Now a year and a half later, the same thing happened. This product was almost $400 at the time we purchased it. I have had better luck with $40 microwaves.

Had our house built in 2009 and the builder carry Maytag Appliances. After 3 years every single appliances start giving us problems. First the refrigerator not getting cold, got it fixed. Then the dishwasher panel, then the built-in microwave, then washing machine. Just the other day the refrigerator broke down again and I was told the compressor was bad. Really? Whats going with this company? All the appliances from this maker dont have longevity. I have 20 year older refrigerator from GE and its still working. Please do not buy this garbage... Its a waste of your hard-earned money.

We bought this dishwasher on 7/8/2013 which is my wifes birthday and boy was that a mistake in many ways! I had 5 service calls on my Maytag Dishwasher MDB7749SBM1 before it went out of warranty. It has issues with the ribbon cable and controller and the control lights are like a disco on the keypad. Now it gets so hot I cant touch the door when its running. So I have had to turn off the power and go get a new dishwasher next weekend which WILL NOT be a Maytag!

Our bottom freezer began building up ice. We cleared the ice and unclogged the drain gasket as per the many instructions that we found online. Researching this problem, I discovered very quickly that this is due to a faulty design of the drain grommet. A new part has been substituted by Maytag. I called Maytag customer service and they refused to supply the replacement at no cost to me and claimed there is no quality issue. This is not about the $20 for the part. It is a leading consumer brand disregarding customer satisfaction. This is also bad business. They will sacrifice their reputation for a $20 part on a $1,000+ purchase. They need to be put on notice that they cannot get away with this in the age of the web where there is total transparency.

When my stackable washer finish its complete cycle, there is water left in the tub. You can manually turn the tub and you can hear water sloshing around.