Like many others Ive read about online, our Maytag fridge model MFI2269VEW5 with bottom mount freezer has ice forming at the bottom of the freezer compartment. The ice then melts and runs onto the kitchen floor. At this point, I am able to prevent this leakage problem by removing the 1/2-inch layer of ice that builds up about once a week. Using a stiff plastic spatula, I am sometimes able to remove the ice in one large sheet but usually it breaks up and has to be removed in pieces. I have seen several videos online showing how this problem can be fixed but as a pensioner with limited income, I am sure the expense of a repairman would be prohibitive. I could likely make the suggested repairs myself but because of a knee replacement, I am not able to kneel for any length of time so that is out of the question. Besides, when we purchased this fridge 3 years ago, we expected it to run trouble free for the rest of our days. This is obviously a design problem and Maytag should be covering the cost for all repairs. However, it is a sad reality that Maytag and their owner, the Whirlpool Corporation is only interested in making a profit to satisfy their stock holders. They apparently only pay lip service to making quality products that last and customer satisfaction seems to be a thing of the past.

It leaves white stuff all over everything. You have to rewash or rinse black clothes at least twice. We have to clean the washer frequently or the clothes smell like mildew. I chose Maytag because I thought they were the best. Apparently, I was wrong and it was a mistake buying this.

MFI2670XEMS - I bought a Maytag Fridge MFI2670XEMS in 2012. I dont remember how long it took to start leaking but it wasnt long. Same thing as what most people are complaining about - I also have hardwood floors that are ruined. I just had a kitchen remodel and now I wish the floors werent new. Warped badly under the fridge. It is a constant pain. I have to break up the ice with a blunt object to get it out. I was so excited to get a new fridge. Of course it was on sale, now I know why. I wish I had just kept the old one, at least my floors would look great. Lame.

I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

I spoke with Mike today at the customer service department at Maytag to see if Maytag would pay for the parts to repair my 04/2010 Maytag front load washer (model MHWE450WW00). The bearing assembly needs to be replaced. So, that means the tub and basket need to be replaced too. The original cost in 04/2010 was $1,088 plus tax. The cost to repair is $1,048. Maytag will do nothing since it was purchased over 12 months ago. I cant believe I just threw almost $1100 away on a washer. Obviously, there is something wrong when an appliance doesnt work after 1.5 years.

Ten years ago I bought a very expensive set of Maytag Neptune Washer MAH5500BWW and dryer units with the single all-in-one pedestal. The washer starts sounding like a freight train during the fast spin dry cycle. A service tech came out, turned it on, listened, told me it is bad outer tub bearings going bad. And the price to fix is $846. Its essentially a throw-it-away deal. The tech says he has done hundreds of these and its a 3-hour major tear down, the bearings are press fitted and you essentially buy a new outer tub instead of replacing the bearings in the old one. Maytag went out of business and was bought by Whirlpool. What a piece of crap and to think how great Maytag once was. Now I have a dryer and a pedestal that probably wont fit any other washer brand.

I feel its kind of cheap. The interior is all plastic which doesnt look shiny and clean as it use to be when it was new. Not efficient in cleaning. Can see still dirt spots in some of the washed dishes.

I bought a Maytag commercial washer - it was pricey but I loved the fact that it had dial knobs and only one feature was electronic as I find the electronics to be what fails the most. It holds a lot of clothes and gets them really clean. I absolutely love it!!

About 6 years ago we purchased a new french door style refrigerator. It lasted one year and one month then needed over $700 in repairs. First you need to know I am into electronics, DeVry graduate with 30+ years experience in repairing electronic devices. The Maytag basically frosted over in the freezer and was warm in the upper part of the fridge. I called a friend who had experience fixing fridges and lo and behold we found something really unusual.The way this machine operates is by blowing the cold air from the freezer up into the fridge. There is a fan located in the back of the freezer wall that does this. We found the fan, which was mounted in a grey box, spinning at about 2 revolutions a minute. My friend took me to the wholesale parts distributor he uses and we gave them the brand (Maytag) model (MFD2561HES) and they gave us a fan... just a fan with two wires. No grey box with fan inside... At this point I got curious, I mean WTF?!?The grey box was made not to be opened and I had to get clever so as to not damage whatever was inside it. After getting it open I discovered the fan inside was wired to a circuit board which upon inspection was a timing circuit. This is why the fan still turned only too slow to function. The new fan was installed and my only problem with the fridge now is the ice maker, which I disconnected.Conclusion: Maytag actually designed this fridge to break down and require hundreds of dollars of repairs AFTER the warranty expired by installing a timing circuit that disables the fan that drives the cool air to the upper part of the fridge to keep your food cold and your freezer frost free. Replace the grey box with a normal fan and youll get years of good use out of your French Door Maytag! As long as you clean the seals regularly and dont mind buying ice to fill the tray with... The repair cost me $39 and a six pack of beer for my friend.

I have bought Maytag products for years. I have a white Maytag microwave that is about 3 years old. It was given to me at 1 yr. old by my sister-in-law when she decided to splurge and create her dream kitchen and went with stainless. The door handle broke in the first year. We glued it. It just recently completely fell off completely-snapping at both ends. I am calling Maytag and attempting to have it repaired. I am otherwise very pleased with this appliance. I have had other microwaves for many years without this happening. Im hoping they will agree to repair.

Bought a Maytag dishwasher model MDB7749AWM2 on 02 Jan 2012 with no issues whatsoever until three days ago when it stopped working altogether and after doing a series of tests I discovered that Im joining a large and growing list of owners with the same problem. I never have been a fan of digital controls due to their vulnerability to temperature and humidity conditions or high impacts for that matter. Ive owned many dishwashers of various brands for upwards of 10 years on average each. This is the first one not equipped with analog/mechanical controls. Im hoping I can still find more of that type.

Freezer does not freeze well. Causes most our food to get freezer burned. We tried turning it up and down but made no difference. Actually went and bought a separate freezer for meats.

I thought I was nuts - only 2 of water in a full machine of bedding or clothes. I agree with all the other one star remarks - clothes still dirty, still dry, hardly any water and if you use the bedding selection, it takes nearly 2 hours to wash a load and then it doesnt spin dry so you have to rinse and spin again. Very disappointed with the machine. Yes - class action lawsuit? How do we do this.

We purchased our Maytag washer about four years ago. I love the features, but occasionally we have clothes rip in the machine. We have had it serviced only once for maintenance. It is great with the large capacity. I can wash bedding including quilts and sheets in one wash. Makes laundry day a breeze for a large family!

Our new washing machine (Maytag Maxima XTLM Front Load Steam Washer & Dryer w/ Pedestals) has developed a loud knocking while running which the authorized whirlpool repair provider said was due to internal ball bearings. He said that the washing machine caused the pedestal to become warped and the only way to stop the knocking was to replace the pedestal. Whirlpool refuses to replace the pedestal saying that the pedestal must have come that way or was installed incorrectly or was overloaded. There are only two of us and we never overloaded at all. The knocking started several months after the installation. If the pedestal was defective (came that way), why wont Whirlpool replace it under their warranty?

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

Purchased the Maytag Bravos XL washer and dryer in January, 2014. Today, 5/16/15 (less than 1 1/2 years later) the repairman tells me that the cause of the loud noise in the spin cycle is bad bearings. Only a 1-year warranty on the machine. I have never purchased extended warranties on appliances so this will cost me $400! Or a new washer since this is more than half the cost of the new washer. This is bad business, Maytag. Ive been a loyal Maytag customer for years but I think Im heading to Speed Queen with their 5-year warranty unless youre going to give me a helluva deal to keep me. Grrrrrrr.

I love the bottom freezer & refrigerator on top. Its so convenient... but it really could have a little more refrigerator space though. I love the stainless steel. It makes the fridge look regal. Also, the fingerprints do not show.

Maytag Bravos XL HE MVWB725BW. Washer was fantastic at first. Then about at 14 months old, the spin cycle starting making loud noises. Called Maytag, they promptly dispatched a repair service. The estimate to fix the washer was $531. The repair man stated Maytag does NOT seal the bearings from the factory. They only rely on a rubber washer, poor design. Maytag was unwilling to help with a washer with their name on it that failed at 14 months in any shape or fashion. She mentioned that Maytag has a 2-10 warranty on the motor only (which is non-existent, its electromagnetic). This will be the last Maytag that I ever intend to purchase.

This washer had good reviews when we bought it, but now today the agitator is not working. I see there are now 100s of bad reviews of this machine most around the same 1 1/2 year mark. How unacceptable to have a large appliance like this break after such a short time. Ive called Maytag to see if there was a recall and there is not. They offered the extended warranty to me for $325 that would cover all parts and labor. Ridiculous.

I owned a Maytag Neptune washer and dryer for 13 years and never had a problem. The only one thing I would say about them is that since the washer had no agitator it would often tangle the clothes, but they were clean and not damaged so I was ok with that. We moved to another house in July 2016, and the moment we plugged in our dryer there was a spark and smoke under it. Our dryer was fried and it was because the previous owner put in the 220 outlet and wired it wrong. So our dryer was dead and cannot be fixed.Since the washer had the small problem with tangling clothes together, I convinced my husband to get a whole new set, not just a dryer. We went to Lowes and picked out a new Maytag Bravos XL, thinking that the brand was reliable and they were so big I didnt have to worry about doing bedding in it. Like ALL of the other reviews of this set, DO NOT BUY THEM! The washer does not use enough water to wet the entire load and you will be left with soap residue on your clothes and they will not smell fresh and clean at all. In fact, my son sometimes wets the bed or has dirty underwear and that is what my entire load of laundry will smell like when I wash them. Imagine taking a load of dressy work clothes out of your dryer and they smell like dirty underwear!I have tried other settings, different types of soap (liquid versus pod, etc) and doing smaller loads. None of this fixes the issue. It is obvious that Maytag and Lowes will do nothing about this issue, according to other reviewers, so Im not even going to bother to have them come out here to do a service call and charge me for it. So Im stuck with a $1,500 garbage laundry set! (Actually the dryer is fine, it just takes longer to dry than Im used to). Im all for a class action suit to get our money back and force them to stop producing such crappy products! Also, if you are considering this set, keep in mind that they have just over a 1-star average rating on this site, and that is because every reviewer is forced to add a rating of at least 1 star. If not, I think wed all pick the zero.

I am renting to own a Maytag refrigerator and it is leaking water on my floor. Runt my floor already - had to replace the floor once. Sent it back to the place where I got it for them to fix it. Paying insurance by the way that isnt worth a crap either cause they wanting to tell me that I left it open at some point or the lights was off at some point. Anyway to make a long story short they gave me the run around and didnt want to fix it. But how do you fight big companies? This was a rental company by the way rent to own so now I have 4 payments left out of 24 at 180.00 each and they still dont want to fix it. I dont know who to be madder at - the rental company or Maytag from selling this piece of junk. But by me renting to own it if any problems occurred they were suppose to fix it. Youre already paying twice the amount to get one cause of credit issues. But thats no reason to double screw someone or should I say triple cause you getting doubled the rental company alone. They need to recall this refrigerator. It has been a lot of complaint and they want to tell you to go behind the refrigerator unstop a line. Well I didnt buy this refrigerator to have to work on pulling it out from the wall every two days to do this procedure. This is crazy. Any one out there looking to buy a refrigerator my advice to you would be do your research and stay away from rental places whatever you do because you will pay twice the amount and they wont stand behind their promise either to fix it as long as you renting from them! And stay away from Maytag!!!

My Daughter got me a Maytag oven with the AquaLift technology and is a piece of Junk. Half the time the Water is still there when the cycle is over. The water has made it between the front glass pieces and the finish on the top of the stove looks horrible, it just looks dirty. The knobs are cheap and the fake chrome finish is flaking off. Unfortunately Im stuck with it because I cant afford a new one... this was a gift to me because Im disabled and it was to make my life easier.

I purchased both the washer and dryer in this series. First the washer does a horrible job actually cleaning the clothes unless you set it as a bulky load and use more water. Despite that issue, after only owning the set for four years the dryer broke down. It made a terrible noise and you could not run it because it was far too noisy. My husband thankfully bought a replacement part and fixed that issue. A few months later I started having trouble with the washing machine. It freezes constantly and I have to unplug to get it working again. It usually take over 15 times to actually get it to begin to fill with water. Now it started to stop working during the wash cycle and I have to unplug it again to get it going. Most times I have to change it to another setting like rinse and spin or drain and spin to complete a wash cycle. Last night it began to have a plastic burning smell. I used to own the same washer for 20 years and only had minor issues that come with extended use. To only own this pair for under five years and have them both break down proves that these are poorly made products and you should save your money and purchase a different brand altogether. I will never buy another Maytag as long as I live if this is how well their products are made. I expect to have my appliances last longer than five years for their price. So save your money when it comes to these machines. I promise you will not be happy with your purchase. I will either have to repair the washer and hope it will last at least a few more years or chalk this up to a lesson learned and discard both machines.

Our washing machine is 3 years old. About a year ago we started to see hairline cracks on the plastic lid in the bottom corners by the hinges. These have now become huge and pieces of plastic are breaking off every time we do a load of laundry. Maytag (under the Whirlpool brand) will not replace the lid for us. We paid $130 for a tech to come out and confirm what we already knew - that we need a new lid. And now the parts and labor will cost over $550. We have called customer service several times and spoken to a supervisor and the best they can offer us is to pay for the part which still leaves us to pay over $400 out of pocket to repair a $600 washing machine. This seems to be a common problem and is all over Google, yet Maytag is not willing to help their customers.

My Maytag Front Load Washer Model MHWE200XW purchased from Sears had a malfunctioning spin cycle. The authorized Maytag repairman from Landers, with support from a Maytag technician by phone, did not know how to repair it. The machine had light use over the past 15 months, and hence was not covered under warranty. So I am out $650 for the machine and $200 for the repair that resulted in continued and even worse malfunctioning. Unfortunately for me, the tests did not show any errors and the machine did not state any error. It just would not spin and then would not allow the door to open. It is a lemon and I do not recommend its purchase.

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

Softener container is clogging up with softener. Worse, the drain in the fridge has frozen up twice and now again I am having to pay someone to clean it out. A pool of water accumulates in front of the fridge where the ice melts. Disgusting in new appliances.

I just want everyone to be aware that Maytag went bankrupt several years ago. They were bought out by another company that still puts the little Maytag sticker on, and all the products are made in Mexico. Apparently all the lawsuits wiped out the company. I did not know this when spent several thousand dollars on one of the best Maytag refrigerators a few years ago. I had nothing but problems with it, and literally had to fight with customer service while it was still under warranty. Needless to say, it only lasted 7 years before the compressor went out, which is roughly $1000 to fix. Kenmore here come...

I give the Bravo T/L Washing machine and the Maytag company zero stars. I had to call for service 3 times within the last 22 months, twice for the electronic panel which needed to be changed, and the third time, it needing a new tub/drive shaft assembly at a cost of $405.27. I did receive a call from the Maytag customer service and all they would do is make a note of my complaint. I feel if you pay almost $1,000.00 for a machine it should work for more than 22 months. I believe Maytag manufactures an inferior product.Not only did it not last, my family and I found that the clothes didnt come out as clean as it should have, and sometimes, the towels would have a mildew smell to them after washing and drying. I assure you that I have read the enclosed instructions of how to use the machine, load the machine, and only used products designed for the machine

We purchased a Maytag French Door Refrigerator with a bottom freezer in 2010. About 6 months ago, we noticed water leaking out the front of the refrigerator. We recently called Maytag service and were told that the refrigerator pan was too small and they would order it and have the independent contractor replace it. The woman I spoke with said that Maytag has been having a lot of complaints about this as the pan put in the refrigerator was too small. In my opinion - an obvious design flaw. The service tech came to our house today with a larger drain...not a pan as I had been told by Maytag (Maytag is the one who ordered the drain to be put in). We ended up paying an unexpected $209 (Pan vs. drainage replacement is a lot more expensive). Needless to say, we are upset for having to pay $209 for a Maytag design flaw as well as not being told upfront what the correct part was that was being ordered. We called Maytag and were told there was nothing they could do because its not on the recall list (yet) and because we didnt buy the extended warranty. We are feeling like suckers and will never buy another Maytag.

This Maytag Bravos is the worst washing machine I have ever had. Who ever heard of washing with almost no water? Takes way too long. Clothes not clean. Any water savings way offset by ridiculous length of washing time. I can wash and dry a load of clothes in an old stacking washer/dryer before one finishes washing in this thing. I was excited to get it and now cant wait for it to go. Wont make this mistake again.

Bought this Maytag washer from Sears and the salesman told us it was the best washer on the market. Well the Maytag washer is a dud. It leave residue on clothes, clothes come out very wrinkle. This washer does not even have a filter. I would not recommend this washer to anyone. We are very dissatisfied. We dont blame Sears, we blame Maytag for even thinking about putting this washer on the market - Maytag model mav7757aww

Re: refrigerator model # MBF2258XEB1. The above-referenced refrigerator was purchased in 2011 from Home Depot. We paid over $1,000.00 thinking we were buying a good product. Right now the bottom freezer is working but the refrigerator is not cooling. An appliance repairman cleaned out the defroster part, but that did not resolve the problem. He said it was a compressor/valve gas line problem. I cannot afford to spend hundreds of dollars to have this repaired. Even though the warranty has expired, I believe that Maytag should pay the cost of the repair. This is VERY inconvenient and frustrating.

Dryer doesn’t wash all the clothes and the dryer doesn’t dry anything correctly. All, regardless of materials or size of load, comes out damp. Repairman’s excuse was that it’s a learning curve(?) and our dryer vent was the cause (which it wasn’t as we had it checked out and there was nothing in it) and that was it. Very disappointed in the washer and dryer and now the company where we bought them as it seems that we’re stuck with over $2K worth of equipment that doesn’t wash or dry well. We’re awaiting to speak with manager for a replacement of anything not Maytag. Not holding our breath and definitely not a happy customer.

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

We had this washer 16 months. We bought it new from Home Depot. The clothes came out with spots on them, white residue and grease spots. This was ongoing for awhile. The bearings went out after 6 months. It was so loud now the water pump went out. I was told by Whirlpool (they bought out Maytag) that water pump is on back order and could take a couple of months!! To fix the bearings and the water pump was almost 700.00. A new washer is 1000.00. We junked it and had to buy a new washer GE. We are sick about this waste of money!!! What a piece of JUNK this Maytag Bravos XL is!! We need to have a class action suit and try to get something back. This is ridiculous and they arent taking responsibility. Whirlpool/Maytag are rip offs!!!!

I purchased my Neptune Washer in 2005/2006. I had a mildew problem, and the store told me to clean it with bleach. It is now 6 years later, and the ball bearings are going out. I called two different repair companies, and were told by both they would save me the call out charge, because the ball bearings were going out, and it would cost between $ 600-$700 to fix, so I may as well buy a new one. The washer is only 6 years old. This is completely unacceptable! I then tried to find someone online to fix it, and I ran into the fact that the Neptune Washers had a recall. Why was I, not notified? I bought the washer and dryer set from a Maytag store. No one tried to reach me. I am now stuck with the problem of buying a new one, and really cannot afford one at this time. I went with Maytag due to the brand name, and I knew it would be reliable. Is the joke really on me? Can someone please call me, and point me in the right direction?

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

I purchased a Maytag 4-door model, a little over three years ago. A little over a year ago, I noticed small puddles of water around the bottom of my refrigerator on the floor. I blamed the dog for having accidents and shrugged it off. Well, after months of putting up with this I came to the realization that it wasnt my dog, so I started looking for leaks on the seal, etc. Thats when I realized that the entire floor of the freezer was one solid block of ice! So, I looked online for people that might be having the same problem. Sure enough, there are A LOT of us!!! Now to add insult to injury, I have to have a MAYTAG certified repairman come and look at what needs to be done! He only charges $85.00 just to come to my house!!!! Thanks MAYTAG, I spend $2500.00 for a refrigerator thats obviously defective, and still have to pay more to have it repaired!!!

We had a wonderful Bisque Maytag double oven in 2002. We bought new stainless appliances this year, and have been very disappointed with the range. Why do you have to hold the temp and timer settings one increment at a time to set it, and why do you have to push Start after that? Frequently we set the temp or timer and walk away, only to find that the oven or timer did not begin because we forgot the new step. When the timer goes off, you have to push it twice to get it to reset. The burners themselves have too many confusing pictures for the settings. What happened to low heat, medium and high and hash marks in between? The stove top itself is a nightmare to keep clean. Give me back my coil stove any day!!!

We bought our refrigerator 14 months ago and it has a 10 yr limited parts warranty. Both the freezer and refrigerator quit working, right after we spent $600 in groceries. I called the warranty dept and the soonest they could get here to service it, was 9 days later cause they only go thru Diamond Preferred, to do the repairs. Then on the 9th day, Diamond Preferred calls to let us know that unfortunately, they cant get here to fix it until another 5 DAYS!! Two weeks with NO refrigerator and freezer, is ridiculous. They should pay another repair place to come out instead of just relying on the ONE!! Our food is now ruined, $600 worth. And to top it off, weve had to eat out costing us more money, and then once its finally fixed, we have to go buy more groceries. I will NEVER buy a Maytag appliance, ever again!

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

I have had it (Model MDB6000AWB) for a few years now. It had to have the door replaced per recall. This dishwasher does not wash dishes well at all; need to rewash many items after going through normal wash cycle. Also, all spokes are burning and falling off, along with pans getting burn marks. I am not sure how safe this is anymore. I am going to purchase another dishwasher, but not a Maytag!

I bought a Maytag MMV1153BAW Microwave. Within a year, the electronic key pad started cracking from normal use. After two years, the microwave intermittently starts then just stops, with the key pad showing 0000. We must unplug the device, or turn the breaker off and on. I called Maytag about the key pad and they said it wasnt covered, and a replacement key pad cost more than the microwave. After two and a half years, we purchased a new microwave, and have sworn never to buy Maytag again.

The fridge has a grinding noise that is getting worse, by the day. I cannot seem to define the exact location of problem, whether the freezer or the fridge. Maytag you stink, and your web site stinks, too.

We bought 10 18-lb washers about a year ago. They are a maintenance nightmare. For example on June 5 7 out of 10 machine were out of service. One has been down since Jan 20 and the others for various lengths of time. The guarantee for these machines has been misleading since the parts for repair are never available. We are losing business and money because of the Maytag failure to provide equipment that operates as advertised. We need help now.

Problem with the front panel are the dishwasher has been replaced 2 times in 3 months. Was told by the tech repair person is not a well made product. He would replace it if he could had a warranty and added a new warranty for 1 year and is up again and of course have to do it. Was told if it happens again they most likely replace with a new unit. Hopefully. Not happy.

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

I purchased my Maytag dishwasher thru Costco. I did so because I got a 2 year warranty if I bought thru them. The washer was approximately 6 months old and they replaced the pump. Approximately 3 months later they replaced the heater. Approximately 4 months after that they replaced the entire operating/electronic board located in the door. Approximately 6 weeks before the warranty was up they had to rebuild the middle dish tray. Now that the warranty is expired by 2 months the door is leaking like a sieve. Unlike most families we use our dishwasher at least twice daily. In summation I would not recommend this brand of appliances to anyone. I will not pay to have this one repaired.

Well I have the washer and dryer. I love the dryer, it is excellent! Now on to the washer. It tries to save water so I guess people in California would love it. I have a laundry room in the basement and one up on the top floor with the Bravos in it. I only do the clothes that are not dirty but a little smelly in the Bravos. Any clothes that are dirty I do in my 20 year old machine in the basement. Do not purchase this machine if you are under 56 because you will need a step stool. Everything I wash I do on the longest cycle because the other cycles do not get all the clothes wet. Think about what I just said. The machine does not get all the clothes wet. Do not purchase this machine. I really cannot call it a washing machine, but they look real pretty in the laundry room.

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

Purchased Maytag Bravos Washer in 2013. Used a little over a year and had to put it in storage for 2 years. Biggest piece of junk Ive ever had. Ive had cheap washers that lasted more than 20 years! Repairman said all diagnostics read normal. I put a very small load in to show him the water was not even wetting the clothes and only swishing them around a little. The shirt on top never got wet and was still in its same position when it went into the final spin. He said this is normal. He recommended I dump the machine and find an old NON Maytag model with the tall agitator!!! Ive tried using all the settings combinations; and the water level never gets all the clothes wet and clothes do not get clean. Will NEVER buy a Maytag product again.

I bought the Maytag Bravos X washer and dryer combo 4 months ago and its been a hassle every time I use the washer. The dryer is fine, but the washer constantly has problems. No error codes, I just hit start and it clicks intermittently in sensing mode for 10 minutes and shuts off. Once in a while, it decides to work - adding water, but never cleaning thoroughly and I always have to run an extra spin cycle because the clothes are sopping wet once it finishes. Ive been reading reviews all over the internet describing similar issues with these models and I am kicking myself for allowing myself to be convinced Maytag is a quality brand. Dont waste your money on these pieces of junk and really do your homework. I wish I had never bought them and am angry that I will have to deal with it until it eventually breaks down in the very near future, Im sure.

I purchased Maytag washer, as it was rated the best of the best at the store. First of all, Delicates cycle washes exactly like Normal. All my sweaters got ruined as the agitation is VERY HARD. I dont think the manufacture even knows what that cycle means! Absolutely awful! Theres no difference between Delicates and any other cycle!Second, Deep fill cycle. If you select off on that cycle the clothes get hardly damp. HOW can you wash hardly damp clothes???? If you go with Deep fill, the washer is supposed to weigh your laundry 1st and ONLY pour the water according to the weight. Well.... you can put only 5 small items and the washer fills all the way to the top! What the hell is this???? How can few items fill such a ginormous washer???? It doesnt work! Im so pissed and want this washer out of my laundry room!

I bought a Maytag washer 3 years ago. Maytag gave me a number for one of their warranty service repair shops in my area. The first repair service doesnt even respond to my calls. The second repair service is a total ripoff. So in summary, Im stuck with a 3 year old washer that has a broken drive assembly that the warranty wont cover.

This is undoubtedly the worst washer I have ever owned or used! I have never before felt compelled to write a review on a product, but I wanted to make other buyers aware. There is not enough water to clean the clothes - the water level doesnt even cover the top of the clothes, so the top of the clothes are dry as they are agitating! After drying (dryer doesnt dry either) the clothes do not smell fresh or clean. Ive put up with it for 3 years and am disgusted every time I use it. Im just about ready to buy another set.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

I purchased a Maytag MDBH979SAB0 dishwasher from Home Depot two weeks ago for around $600. I got it installed and it would not turn on. I contacted Maytag and after a few questions, she stated that they would have to send a repairman. After a few days, the repairman arrived and said hed never seen this model before but that we needed a new control panel. After waiting a week with no work, I called Maytag to get an update. The control panel is out of stock and could be a while - they are trying to find one somewhere around the country. They refused to send a replacement dishwasher, even though this was brand new. Their policy says repair, not replace. Dont take the chance purchasing a Maytag dishwasher.

I unfortunately just had the same issue concerning my unit. The unit went berserk, stopped cooling and ruined all my food. I managed to get it outside after leaking spoiled food all over my floor. I washed it out and contacted Maytag after reading the hundreds of complaints. They sent someone out to fix the panel but he couldnt get it to cool. He said many times when a unit goes down that the acidity from produce along with moisture can eat through the aluminum components causing a freon leak. Obviously, this happened to me. I contacted Maytag and they said they would fix that too but once I called back, they said that it was a separate issue. Then I spoke with another person who said they would send a tech to inspect. I took off work and finally got a courtesy call from tech saying he was told not to come. I was amazed I missed work waiting and got no call from Maytag saying they changed their mind. I called back in and was told flat out I would not be covered, even though the fridge was fine before this happened. I suggest everyone read over the Consumer Protection Act which covers defective equipment causing issues by both injury and property damage. A class action lawsuit needs to be organized concerning this also. In the meantime, I implore each of you to file a complaint with the Better Business Bureau in your state along with Michigan where Maytag is headquartered. This will guarantee a response from corporate. Also, make copies of this forum and send it to your State Attorney General explaining how you have been sold a defective item. They say ABC news once did a segment on this fridge issue also, so I suggest contacting them asking for a follow-up story. For those that use social media, go onto their Facebook and Twitter page to post a link to this site and the way you have been treated after spending over $2,000 and a fridge that has lasted 7 years or less. Its time for small voices to unite to form one that is much larger.

We purchased our Maytag Refrigerator brand new, about 18 months ago. It always ran loud so the repairman came out during the 12 month warranty period. He told us to unplug and reset it, but that never did the trick. Eight months later, the fridge stopped cooling. We called our local repairman and he told us ($97 later) that the compressor was out. He said we should contact Maytag because the compressor should be under a 5-year warranty. Then the nightmare began. I spoke to four different reps with a total hold time of about 2 hours. Two of the reps put me on hold to get a supervisor and/or consult another rep and I was mysteriously cut off each time. One rep told me my compressor wasnt covered under warranty. The last rep I spoke to told me it was covered and he scheduled a Maytag repairman to come and replace the compressor. I was thrilled. The repairman came out and informed me that the compressor was indeed out and handed me a bill for $137. I asked why I was being billed and he said because that was the way that Maytag had ordered the service call. I told him that the Maytag rep had assured me that Maytag was covering the repair. He apologized and said that not only was I obliged to pay for the diagnosis (which I didnt need because I had already paid my local guy for the same information), but that it would cost $900 to replace the compressor. I was flabbergasted. I called Maytag and they denied all responsibility. They said that even though the rep had assured me of Maytags commitment to replace the compressor under the 5-year warranty, he had made a mistake and I wasnt actually covered. So I paid our local repairman to replace the compressor, because by that time, we had been living out of ice chests for 2 weeks. That was 3 weeks ago. Now the unit is freezing water on the bottom of the freezer and then leaking water on the floor. It is unconscionable that this company be allowed to defraud people to this extent. I will never buy a Maytag again and I would like to be informed of any class action suit. This company should be deeply, deeply ashamed of itself.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

I researched gas ranges for a few months before choosing our Maytag gas range - it was on sale when we ordered it and it arrived within a couple of weeks. We wanted to buy local and were successful with price matching the sale price. I would recommend this range as it functions great and we totally love the larger oven door.

We purchased the washer and dryer pair...beautiful looking, no agitator, water efficient. Load sensing feature. TERRIBLE, TERRIBLE, TERRIBLE. WORST APPLIANCE WE HAVE EVER PURCHASED. Used it 3 times. Clothes would not rinse, left white soap residue in the folds of the black clothes, even after a second wash. Home Depot was just the GREATEST, they replaced it for us. We went with a less expensive model GE. With the agitator and full water load...save yourself A LOT OF TROUBLE, stay away from Maytag Bravos XL.

Our Maytag Bravos is 4 years old. Settings are preset at the factory. Besides the glitches others have written, the hot water sensor INSIDE the machine has gone out. This means - no clothes can be washed on the hot setting, and the warm setting gives only lukewarm water. I have had more than one plumber look at the machine, and the consensus is...the internal sensor needs replacement. However, this machine being only 48 months old, I am debating whether or not just to buy a new machine. This is a HE washer, and I am very disappointed in its performance. This is the worst Maytag machine I have ever owned.

I bought the Maytag Centennial Washer a year ago. I have had nothing but problems. The clothes never get fully wet so you have to wash clothes 2 or 3 times. The lid does not open when running. So you cant put soap after the clothes are damp. I say damp because they dont get wet. Right now the sensing light has been on for 2 hours. I need to catch a flight in the morning and I cannot wash my clothes! My white clothes never get clean. I have to wash 2 or 3 times. Actually 4 time would work better. The water and electric wasted with washing over and over again is nuts. Stay away. Ive warned you!

MAYTAG BRAVOS WASHER - Biggest mistake I have ever made, like all the other complaints, washer does not clean the clothes. This washer and dryer are in our vacation home. Only used on weekends we are there, now the washer is broken, will not spin and UL light comes on, even with no clothes in it. DO NOT BUY!!! Like others have stated, we need to start a class action lawsuit against Maytag for fraud and knowingly selling junk.

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

We purchased a Maytag Dishwasher in 2011. In 2014 I got no response from the control panel when trying to start the machine. Service came out and had to replace the control panel. The cost for that repair was $269.00. It has now just stopped working again. Same issue. After seeing all the posts, I realize that this is a prevalent issue and in some cases a safety concern. If Maytag knows about this issue with their control panels why have they not recalled or corrected these problems! Needless to say, I will never trust this company again!!! Model number MDB7749AWM2.

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

Bought a brand new Maytag French Door Bottom Mount refrigerator in 2014 to simply upgrade to stainless steel. Put my old refrigerator that I have had for 17 years in the garage. Never EVER had an issue with it and it still runs perfectly. Well, just out of warranty in May of 2015, the ice maker stopped working in the new Maytag. Called and got service. Learned there was a recalled part. Service man fixed. 2 days later, it broke again. They came back out and fixed again. This time, the motor was REALLY LOUD. They came out to replace that. Now, both the freezer and refrigerator are not properly cooling. Cannot keep ice cream and cannot make ice. Called again. I was told these dual fan systems simply do not work. I am out of warranty and too bad for me. A wasted $2500!!!

MTB2656DEB - Well my fridge is now about 12 years old and from the beginning it was horrible ice as always forming under freezer door. The cold cut draw broke 3 times with its cheap junkie plastic. I hated it from the beginning. I have owned a GE double door with ice maker for 26 years. Wish I had kept it.

We purchased a Maytag washer model MVWC400XWO almost 2 years ago and it has problems with the bearings and the whole computer board is defective. I was told to buy the extended warranty for $350, which we did. As of today, we were told by extended warranty they are refunding our money because there are so many things wrong with this washer, including the whole computer board, that it would cost them too much to fix or replace it. Im in complete shock. We paid well over $500 and are still making payments on it. I spent the day reading hundreds of reviews from people with these exact same problems and Maytag is aware of it and will not help. They should not be selling these anymore. Im completely sick to my stomach. I cant afford another washer and when I called Maytag, they said it was past the year and we are out of luck. I cant believe this can happen to people and they get away with it. A washer should last longer than 2 yrs.There are hundreds of people going through this with Maytag and no one will help.

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

MHW7100DW Maytag Washer Steam & YMED7100DW Maytag Dryer Steam. Both of them are easy to use. They hold lots of clothing as well as bedding and many different settings. They both do an excellent job. Brand and excellent reputation. Had my last Maytag washer & dryer over 25-years and had no problems with either. Thats why I bought Maytag again. Repairs are very costly when you have to pay technicians. Dont like poor quality construction or enamel chipping when you place items on them. Very easy to clean both of them. Practically no lint dust emitted into the room from the dryer. Had no problems with my previous washer & dryer. Thats why I purchased a full size Maytag washer and dryer again.

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

We received a MayTag Microwave on Saturday May 10, 2014. There was a minor ding in its case, but it did not show any other damage. After installation I tried to use the microwave. It did not work. So on Monday the 12th I called 800-688-9900 for service. A service appointment was scheduled for Wed May 14th. The service man told us the microwave could not be fixed and had to be replaced. I asked who should replace it. He told me to take it back to the place of purchase.I took it back to the dealer and after a lot of discussion it turned out that MayTag had to replace it. I was given a case number. I called Maytag and was told replacement could take 4 -3 weeks. I could purchase a new microwave and have it by Friday may 16th much sooner than Maytag could do.

The Maytag dishwasher works really well. Not the quietest, but cleans thoroughly. I dont use heated drying though, to save energy. Stainless steel interior retains enough heat to mostly dry. However, unit died after only 7 years. Expected longer life.

I love the functionality of this Maytag refrigerator. The inside is so nice and big, I can almost fit anything into it. When I need to make a lot of food for a lot of people, this refrigerator really foots the bill.

Maytag Bravos XL Washer & Dryer - After a long 45-year use of our old GE W./D. that were still working fine when we decided it was finally time to upgrade. Big mistake. Nothing but dissatisfaction on every level of complaints by those who registered here before us and then some. This all was noticed almost immediately after purchase, but we lived with it trying not to believe our worse fears. That is until we both started breaking out with skin rashes. Just logged on this site after a Google search... We were shocked and disappointed in our purchase decision. We will join in a class action lawsuit if ever one is initiated... Any lawyers with one of these?

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

We bought a Maytag dryer and within two years the drum cracked. It will cost over $500 to repair it and then will the new drum be better? I bet not. Piece of junk.

It is nice to know that there are other people out there that have the same problem with the Maytag washers cabinet inside and outside rusting. Our rusting is around the bleach area rim and on the outer seam of the washer. Our washer is now 4 years old. We started having the rusting problems in 2011. We called Maytag and of course. They are sorry for our problem but cant do anything about it. They made it sound like we were the only ones having this problem. We need to stand strong and continue to complain about this problem until Maytag takes responsibility for their poor quality washers. Anyone out there looking to purchase a washer. Do your homework. Buyer beware of Maytag washing machines!!!!

I have a Maytag dishwasher; a nylon roller for the upper rack cracked. It is held in place by a hex head screw. The roller is about $1.75. Maytag will not sell me the roller. I have to buy a complete rack adjuster assembly for $46 to replace a small nylon roller that screws in. I have had these problems before with them. I guarantee that I will never buy another Whirlpool-manufactured appliance. This is ludicrous!

An average refrigerator/freezer at best. I would not recommend it unless you also buy a service agreement to fix things that go wrong with it. Ice maker went out.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

I bought this Maytag MCT washer and dryer set brand new from Lowes October 31st, 2016. When I washed the first load it made so much noise I thought it was broken. Called Lowes and they said it is just noisier than the older ones. This is the water/load sensing model, supposed to be great. I am usually here by myself, so at most I wash one load of clothes a week. I have a queen size mattress pad in there washing right now. This pad fills up the drum pretty much, I have it on deep water but that only gives me maybe 1/4 of the drum that has water in it. The pad is wet from wicking, NOT from the water covering it. How is this supposed to clean anything when the water is not covering the items?When it spins out, it gets off balance easily. The manual says to not worry about balancing load as you put it in there, but doesnt make any sense to just cram on one side as the water isnt going to float the cloth around to balance. The settings for Bulky does nothing more than the setting for Deep Water, you still do not get enough water to wash your clothes.It also does not do any good to add fabric softener to the machine, as it seems to just take it all out, you cannot smell any fabric softener on your laundry when you are transferring it to the dryer. And the laundry when dry isnt soft like it was with the old machines. I will be 62 in December 2017. My parents always had Maytags, never a problem. This is the 4th set of Maytags I have had. And bought a set for my daughter in 2013 also. And this by far is the worst. Their quality is completely gone now. Nothing but cheap made products that are predestined to fail. Friend across the street said she had looked at this set when she was in market to get a new set. She has an friend who works on appliances and who works for stores selling these models and he told her, they were not worth buying. Wish I had known that. Do not waste your money.

I bought a top end Maytag refrigerator with the freezer in the bottom drawer. Spending the extra buck was something that I thought was worth it, being a Maytag. Fifteen yrs go by and it stops completely. It cost me 200 bucks for a service technician to tell me that the compressor or it has a leak. Its not worth repairing. With todays cience and technology, you would think that they can make a refrigerator last for 25 yrs or more, like the old ones. We went to the moon 44 yrs ago. Why cant they make them to last? I think that the corporations figured they can make more money making an inferior product that needs to be replaced every 10-15 yrs. I will never by a Maytag again.

Never liked this machine. No flexibility in settings, ruins clothes, noisy and often shuts down. But main concern in the fact the whole top is rusting by the bleach dispenser and it leaks from the top all over. It is only 3 or 4 years old. Can not believe an expensive product like this can be so bad.

I bought this Maytag dishwasher model mdb6709awq1 from Home Depot that installed it; they did a good job installing for a fair price. My gripe is with Maytag. I have owned a Maytag dishwasher since 1977. Back then it was the best you could buy. Since Maytag sold out to Whirlpool to save being bought by the Chinese, the design of the dishwasher has lost or gave up their unique design that made it so good and dependable. The inside of the rack/drawers has been totally changed. It used to have fold down racks on each side of bottom rack that was great for coffee mugs, small bowls/containers, and they came out sparkling clean. The utensil basket was centered front and again the utensils came out super clean. Maytag sold their soul when they sold out to Whirlpool. Dont know if that was part of the deal that they give up their unique design or why did they change the rack design. I wish I still had my old Maytag from 1998 that yes, worked without a problem, then I sold the house with the dishwasher. Why is it that so many appliance makers have taken dependable workhorse designs and phased them out? What is wrong with an appliance lasting for years, decades without problems? Only thing I can think of is that they wont make millions every year as they only would sell so many a year if they are dependable as they wont need to be replaced.

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

On March 2011, I purchased a Maytag dishwasher model #MDB7749AWB1. The dishwasher worked excellent for 16 months. One morning, with dishes loaded and ready to go, the start button would not light up. The other buttons did light up but that did me no good, I need the start button. A few days later, none of the buttons would light up. I found a repair person who said it would cost over $200.00 to make repairs. I refuse to put another penny with no guarantee that this new part would work. I will never ever buy another Maytag appliance. The last inexpensive, unknown manufacturers dishwasher lasted me 13 years. Do not waste your money on this thing.

I had to replace a washer & dryer which was destroyed in a fire. We lost everything. I was hoping a new set would last me many years. Boy, I was wrong. Maytag Bravo washer is the worst by far. I havent even had it 4 years. I had a plumber in 4 times already. The pump keeps breaking; it doesnt drain properly. It appears that dirt is entering the clean laundry and the laundry has to be washed again. It looks like I have to research for a new washer. It wont be a Maytag. They are thieves!

I bought a Maytag dishwasher, model MDB8551AWB, in 2007 and have kept purchasing maintenance agreements. From January 2011 to March 2012, I have had to have Maytag send out a repairman to replace the control panel five times. This is absolutely ridiculous, and the inconvenience. Plus the repairmen are surprised Maytag keeps on repairing this dishwasher and not replacing it. More the $2000 has been put into this dishwasher since January 2011. When calling Maytag, I was informed that the problem would have to be the same which it has been but on the same contract for it to be classified as a lemon. Well, it has now been four times. I will never purchase another Maytag.

This washing machine just sprinkles water on your clothes then ties them up in knots. And to add insult to injury, needs repairing every year or so. Horrible! It does have a couple of redeeming qualities, but they definitely dont outweigh the cons. It spins the clothes quite dry and has a large capacity. I have dogs and kids who play football and a husband who does construction, and its not unusual to find lumps of dirt and fur trapped in an article of clothing or blanket. All my bras and sweaters get ruined, it twists them up horribly. The blankets and sheets end up in a mushroom shape. Sad to say, NOT good. I like Maytag, but not BRAVOS.