Two months after my warranty expired, the motor burned out on my dishwasher. I called Maytag to see what they would offer, but they would only offer a discount on the actual part. I was so angry I was ready to buy a new dishwasher and forget about them...but I dont have that kind of cash to throw away. After going 5 weeks without a dishwasher (first-world problem) I paid for the part and a repairman to come and fix the dishwasher. Now 3 months later, the touch panel wont work. I am so upset that I wasted the money to fix this piece of junk. I will never purchase another Maytag again.

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

Purchased the Neptune washer & dryer in 2002. Did not purchase any additional warranty. I have had Frigidaire, Kenmore and Speed Queen washers previously and used them until they quit. I have not had any problems with either the washer or dryer. No mold, no smell, nothing. I did laundry for 2 children and 2 adults, 6 to 8 loads per week with half being heavily soiled work clothes. I still wash 3-4 times a week. I was able to wash & dry king size blankets and comforters for the first time with this set. Washer and dryer are located on the main floor of house and are the quietest units I have ever owned. They may quit tomorrow, but they have done the job that they were designed to do. I am well satisfied with the quality and performance of both units and would not hesitate to purchase Maytag appliances again.

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

Maytag MCT Washer & Dryer - I bought the largest capacity to save time. However even my 6ft tall husband has problems reaching the bottom to remove clothes. Even worse is the lack of water to clean clothes, washes so long it wears clothes and they are still dirty. I tried to improve on my old Neptune and Id love to have it back. I may have to junk this washer. The dryer is very slow. Buying this set was tossing my hard earned money in the trash.

I have a similar story to Patricia. Been without a fridge for over a month. Refrigerator is almost brand new (bought last year) and a service-person has been out three times (going on 4) to fix it. The fixes NEVER work and then they have to order ANOTHER part and I have to wait for the part AND THEN the service person. I should not have to wait once the part comes in. People who have been waiting should be at the TOP of the list. Then again, this is Maytag...probably EVERYONE has been waiting for a fix.Ill never buy a Maytag appliance again unless they give me a new appliance, pay for the apartment sized refrigerator I was forced to buy while I waited--I have 3 children who need fresh food--and replace the $300 worth of groceries that went bad when I was assured the second fix would work (they wont replace my refrigerator--if they do, Ill be satisfied--unless it breaks in less than a year, too).

I purchased a Maytag Microwave Oven MMV5208 WS 1 from Home Depot less than two years ago. Mine was actually manufactured in April 2013 according to the ID tag. A couple of months ago it started acting up because a switch when the door closes began to malfunction and you had to open and close the door several times to get the microwave started. Then all of a sudden when you set the timer and pushed the start button it would flash on and immediately shut off. This is extremely frustrating because I paid more than $400.00 and purchased it less than two years ago. I am disappointed because Maytag advertises its reliability and this microwave is anything but reliable.

In October 2017, I purchased a Maytag MVWB765FW0, thinking that it would live up to the Maytag reputation but I will NEVER buy Maytag again. This machine is more suitable to wash industrial canvas rather than clothing and bedding. All the laundry is twisted and mangled and ends up in a large tangled ball at the bottom of the tub. My clothing is being destroyed faster than I can replace it.

I like Maytag but my low water no agitator washer does not do the job as well as it could. Also if a coin gets in the washer it is very hard to get out of the crevasse in the tub area. Most people from time to time have some change ending up in the washer...it should be easier to retrieve.

Maytag Bravo Quiet Series 300 MVB700VQ - My wife and I feel this is one of the worst machines sold. We purchased it from Costco 2 yrs ago and had several issues over the years. Pump, locking, water level, small clothing items like socks getting in behind the drum and clogging the pump, and yesterday a flooding issue. That is right, my Bravo 300 did not shut off and the water ran continually with an LD code displayed. The water overflowed into the kitchen & pantry. The wood floors are now warped. We were home so we were able to shut off the water as the washer controls (buttons) were locked and not responding. We spent the better part of 3 hours moving items and wet vacuuming the house. We now have a dehumidifier running in hopes we can salvage the wood floors and minimize mold growth.I will note that I have a home warranty (third party) that covers repairs on my appliances, this washer included. The repair man thought it may be the pump, a line, and/or the control panel/module that need replacing. The repairs would be covered by home warranty.... but not the floors. There is NO WAY I am fixing any washer that flooded my home.Yesterday, I took a 3 yr old washer with known issues back to Costco. I was not happy with the manufacturers suggestions that I buy parts as it was Out of warranty. Again, I had a third party warranty so the repairs would have been covered! It is clear that the manufacturer doesnt CARE about the quality or the performance of this machine. I have found a FIX for these issues. We are buying an LG Washer that is more $ and is highly rated by Consumer Reports. Stay AWAY from this model and current repackaged models of Bravo/Cabrio!

I bought the top of the line Maytag washer. I was told they have improved their washer so that it no longer requires an agitator. I was also told the new machine saves you money by using less water. It has a sensor so that it only puts the water needed to clean your clothes. Instead of filling up with water and having the agitator to stir the clothes around, this new and improved machine puts a small amount of water in the machine and vibrates. The end result? All of the dirt and debris gathers in small pockets and sticks to your clothes. In order to save water the sensor only allows a small amount of water to enter the machine to rinse your clothes. When you consider how many times you have to go back and rinse your clothes before you get the caked on dirt off of your clothes, its costing you more money, more time and more aggravation. Oh yea, the maintenance man was out three times before the machine was a year old. The last visit was to replace that fine Maytag motor that was less than a year old. I have pictures that show my clothes with caked on dirt and debris on them after they have completed their wash cycle. It is HORRIBLE!!!

We were sold a Maytag Neptune washer mah550bbw in 2004 when it was already on recall by Maytag and a class action lawsuit was filed against Maytag. We also bought an extended warranty. Now we have the same problems as the lawsuit. We own dry cleaners so we do laundry once a month for small articles. For the last few months the clothes have an odor and they come out looking not clean. We were sold a defective and recalled product and are not happy right now. We would like a fast resolution to this problem; otherwise, we seek legal actions.

This washing machine is good for cleaning clean clothes, like stuff you wear one day at a desk job. But nothing dirty. Its really bad. Dont fill it either, nothing will get clean. 1/2 full or less. If you put too much clothing in there it will leave lint and other debris all over them. Also, dont use granular detergent, it wont dissolve or rinse out. Liquid detergent only. Weve had it for about two years, and its a constant disappointment. A total waste of money. Really annoying. I have to get rid of it. Its almost completely useless.

I purchased top of the line Maytag washer and dryer in 1975! They are Harvest Gold. They were sold last week along with my house. I now have Whirlpool appliances in the rental apartment I moved to. There are some irritating features.

Purchased the Bravos XL top load washer a month ago. We work outside daily and our clothes get very dirty. I havent really taxed the machine yet (Im doing what I consider a normal load of wash. I know the machine could handle twice as many clothes as its the 5.3 cubic feet washer, but I havent had that many clothes to put in at one time). The washer works great. Clothes are clean and smell fresh. For those that say this washer is extremely loud - you must not have something set up incorrectly. Either the wet pan you put under the machine is making contact with parts it shouldnt or someone didnt level it properly. Really, this is NOT a loud machine. We purchased from Lowes and they delivered, set up and leveled both the washer and dryer. (Yes, we also purchased the matching Bravos XL front load dryer and were impressed that it dries our clothes in half the time our old one did). We would definitely recommend the Maytag Bravos XL washer and dryer.

I find this Maytag dishwasher just ok, nothing special. It doesnt seem to clean any better or worse than other dishwashers I have had or used in the past. It also seems to get really slimy under the inside of the door.

I have only had this machine for 2 weeks after having a Maytag since 1994. Even broken, my old machine was far superior to this one, a Maytag Bravos. Fortunately, the salesman noted that I wouldnt be happy with this machine but, thanks to a government mandate, all new machines behave in a similar manner to save water and energy. This agitator-less machine neither washes nor rinses the clothes/bedding/towels properly. It takes four times as long to wash the items but doesnt get them nearly as clean. Today, I put 2 pairs of shorts, 2 T-shirts and a standard bed-sized mattress cover in to wash. The mattress cover never even got thoroughly wet even though I used the deep wash and extra rinse settings. Last week I put sheets in the sheet setting only to have them come out totally wrinkled and stiff as a board with soap even though I used the recommended amount of detergent. This is a disaster. Shame on Whirlpool/Maytag and the U.S. Govt. A river and a flat rock would work better!

MFI2670XEMS - I bought a Maytag Fridge MFI2670XEMS in 2012. I dont remember how long it took to start leaking but it wasnt long. Same thing as what most people are complaining about - I also have hardwood floors that are ruined. I just had a kitchen remodel and now I wish the floors werent new. Warped badly under the fridge. It is a constant pain. I have to break up the ice with a blunt object to get it out. I was so excited to get a new fridge. Of course it was on sale, now I know why. I wish I had just kept the old one, at least my floors would look great. Lame.

Bought my Maytag washer and dryer as a set in Feb 2011...like many, I did not get the extended warranty, as I thought this was a great brand. Ive had nothing but problems with both. The dryer takes two rounds to dry, the lint filter is wet and rusted. The belt has popped off and needed to be put back on..The washer does not clean very well. Ive replaced the shift actuator because it was not spinning, now it sounds like a turbo jet taking off. And as of a week ago, my washer started leaking underneath. Paid a tech to come look at it and said my motor was done and Im better off buying a new washer and even recommended that I do Not buy Maytag! So I googled Maytag Bravos and seen all the poor reviews and realized I wasnt the only one! My set is 3 years old and its ridiculous that Ive had these issues, as so many has. Extremely disappointed of this brand and I too, will not be buying Maytag ever again!!

I am absolutely disgusted with this Maytag Bravos XL washer. Have owned it 6 months and cant wait to get rid of it. We live on a farm and have cattle. If jeans go in the machine with mud on them, they will come out with mud on them. I have tried soak, deep water wash, power wash. Nothing works. I might as well put a wash tub in my back yard and wash by hand. Anything black must be washed by itself as it will come out covered in lint. How did this machine ever go on the market? Expensive mistake. Please do not buy this machine.

A company who sells a washer that makes washcloths/towels smell musty as you take them clean from the drawer should be ashamed and refund everyones money!!! I have always love Maytag/Whirlpool products until this piece of trash washer. My husband, who is retired from Maytag, gets a very nice deal when buying their products under the VIP program. However, how nice a deal is it when you have musty/sour smelling towels after washing??? Ridiculous! Seems that when the washer went to no agitator and water/electricity saving they forgot what the purpose of a washing machine was. Im very upset and would NEVER recommend Whirlpool/Maytag products to ANYONE!

I didnt want something from Sears due to horrible experiences with them. Maytag is very reliable and the cost was reasonable. They fit in the small space available for washer and dryer. They have all the features I need. The only complaint I have about the dryer is that for some reason if the load is small, it takes longer to dry than with a full load. I have had them for about 5 years now. I expect a washer and dryer to work correctly every time. If its poor construction I would not buy it. I also expect an appliance to last many years with proper maintenance.

The washer does not get clothes clean at all even with the help of odor blaster, does not spin right, does not even out the clothes, walks while it is spinning. My towels do not smell good at all. The dryer gets too hot and the lint trap is always a mess even though I clean it after every use.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

In July 2006, we purchased a Neptune Washer. The only problem we had with it is it does NOT spin the water out of the clothes after the wash cycle. This has been going on for about 4 years. In February 2012, we had a service person to examine the washer. According to the service person, there is nothing wrong with the washer. He said to put in clothing of the same type: All towels, all jeans, all pillowcases, etc. This is not the real world. This cost me a service call with no solution. On June 10, I called Maytag on my issues. They have no recalls or issues with this washer. They recommended another service call which I refused. I even offered the washer free of charge to the person I was talking to, but did not get a response. Never again will I purchase a product from this company.

Same issue as everyone else. After about 15 months the control panel on my Maytag dishwasher model#MDBH979SAM1 has malfunctioned. First it would only let me choose the rinse option but now all the lights are turning on and the dishwasher will not stop washing but yet the dishes are still dirty. I called Maytag and they quoted me 249.00 to fix the issue. But if its a common problem with this make and model why do I have to pay to replace the panel. They should recall this model or replace the panel with an updated one that wont have the same issues! I cant imagine paying 249.99 every year to replace this panel that seems to malfunction no matter what you do!!! I paid around 550.00 at the home Depot for this dishwasher! It did not even last me two years!!! I want a lawsuit filed against this company and I want my money back or my dishwasher replaced with one that works and wont have the same issues!!!

Bravos mct. Unbelievable, this washing machine is terrible, no water. The water level doesnt even cover 6 items. Have to wash triple the loads of my old washer just to get the clothes clean. I have to go to the laundromat twice a month. I shouldnt have to do that. Almost want to fill the washer with water, but dont know what will happen. Very unsatisfied with this washer.

My dishwasher, purchased in 2013 sings the same tune as many of these complaints...stopped working correctly, turned on whenever it wanted to, etc. Thought it was the cpu...no. Called Whirlpool and they gave me the same runaround that they give everyone...more money for a temporary fix. Did some more research that led me here and discovered that the ribbon cable leading to the control panel was fried due to heat and moisture. Easy to check for yourself... looks like brown crap on the cable...if you have a meter, you can easily check it. Tried to repair it, very difficult, but I tried. NEWS?...I wrote a complaint to the Better Business B... and mentioned that this is a safety issue, which it is.Believe it or not, just received a call from the corporate office (Whirlpool) and they were interested...I actually got their attention. They said they would have someone contact me... she did today... so this is encouraging. I dont know what they are offering, but this poor design is a serious problem, and if you want to get in Whirlpools face better go through the BBB. I already have purchased a new part and am adding silicone to the cable to protect it from the heat...but Im really seeking full reimbursement because this is not going to end well. Good luck...

Bought va washer. Trying to upgrade. Water fills about 1/3 of way even on bulky setting. Supposed to be high efficiency. Detergent does not get all the way out because there is no enough water. Have to put it through 2 rinse cycles. Worst machine. Design is flawed. Clothes all wrinkled. I cant afford to buy clothes and have them ruined. Man must have designed. Hate the washer. Im poor and they want take it back... want my money back. I cant buy washer every day. I will keep on complaining. No customer service. People just put you off. It is a Centennial high efficiency. A piece of junk.

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

Maytag Dishwasher MDB7749SBW3 - Control panel problem just like everyone else describes. Bought in Nov 2014... how disappointing!! My husband is sure he can fix it if I buy the part. I went online to order the control panel, and of course because Im in Canada I cant ship the part directly from the website, I have to call the Canadian Sears Part Dept., its about $200! As I came across all these reviews I am even contemplating if I should waste our time and money trying to fix this thing... Maytag never again!!!

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

I owned a Maytag Neptune washer and dryer for 13 years and never had a problem. The only one thing I would say about them is that since the washer had no agitator it would often tangle the clothes, but they were clean and not damaged so I was ok with that. We moved to another house in July 2016, and the moment we plugged in our dryer there was a spark and smoke under it. Our dryer was fried and it was because the previous owner put in the 220 outlet and wired it wrong. So our dryer was dead and cannot be fixed.Since the washer had the small problem with tangling clothes together, I convinced my husband to get a whole new set, not just a dryer. We went to Lowes and picked out a new Maytag Bravos XL, thinking that the brand was reliable and they were so big I didnt have to worry about doing bedding in it. Like ALL of the other reviews of this set, DO NOT BUY THEM! The washer does not use enough water to wet the entire load and you will be left with soap residue on your clothes and they will not smell fresh and clean at all. In fact, my son sometimes wets the bed or has dirty underwear and that is what my entire load of laundry will smell like when I wash them. Imagine taking a load of dressy work clothes out of your dryer and they smell like dirty underwear!I have tried other settings, different types of soap (liquid versus pod, etc) and doing smaller loads. None of this fixes the issue. It is obvious that Maytag and Lowes will do nothing about this issue, according to other reviewers, so Im not even going to bother to have them come out here to do a service call and charge me for it. So Im stuck with a $1,500 garbage laundry set! (Actually the dryer is fine, it just takes longer to dry than Im used to). Im all for a class action suit to get our money back and force them to stop producing such crappy products! Also, if you are considering this set, keep in mind that they have just over a 1-star average rating on this site, and that is because every reviewer is forced to add a rating of at least 1 star. If not, I think wed all pick the zero.

On June 5th, my husband turn off the water to the house since we were going to be away for 4 days. Unfortunately, it was not completely turned off. When we left, the washing machine was OFF, with the door slightly cracked open (to allow for circulation). When we returned, there was water all over in our upstairs, plus water had gone down the walls to the lower level. We could not figure out how the water got into the washer since it was turned off. The insurance company asked that we call a repairman to find out what was wrong. Fortunately for the repairman and us, the machine continued to go on and on after the Curtis had checked it out (it pumped out for him but not for us) and turned it OFF. It jumped from cycle to cycle after he had turned it off. Obviously the control board did its own thing. Be aware-- it can happen!!

I have always bought Maytag and never had a problem except with this new washer. Our clothes smell like dirty laundry and when done washing there is lint in the creases or folds of the clothes. I am using a product for cleaning the washer each month, but our clothes still have an odor. I do not like the way the washer works, it just moves back and forth slowly, but the clothes dont circulate enough.

I purchased the Maytag refrigerator MFF2055DRM on 7/7/16 new. It was suppose to be stainless steel; but now I am seeing rust spots at the top and bottom of the French doors. I clean my refrigeration weekly and find it odd that now it is rusting. Also, I am able to place magnets on the doors - which should not be for stainless steel. In addition, I spend over $100 a year replacing the mandatory filters. I must also place the setting to high to maintain my milk and juices. I must also have to place them in the very back of the refrigeration. I am a single senior and my refrigeration is not overloaded with food; nor am I constantly in and out of the refridge. Not very happy.

Bought it in 2013. Just replaced freezer motor. I thought for sure it would give me better service.

I bought the Maytag Bravo XL MVWB725W washing machine and dryer pair in August of 2015. 2 months after I bought the pair the thermostat went out on the dryer. It was under warranty so it was fixed and no problems after that. In July of 2016 I have my first stainless steel hose break at the fitting because of corrosion flooding my laundry room. I thought it was a fluke so I put another one. The next hose started to corrode in September 2016. We thought there was some weird chemical reaction going on between the hose and the filter on the back of the machine. So we changed to rubber hoses in September. Since then we have gone through 6 sets of rubber hoses. We have had the water company out, they say our water is fine. A plumber out, our new water heater is fine as is our plumbing. An electrician, who changed an outlet and put a grounding wire on our house water line. And an appliance repair man, he found the problem so he called Whirlpool who makes Maytag. There is corrosion on the water temp control. However nobody has EVER seen this problem and doesnt know how to fix it. Not even Whirlpool. And Whirlpool says its my house. Im at a dead end with a washer that is constantly going through hoses. It really doesnt wash clothes very well either unless you put a lot of stain remover on the clothing before and wash it in hot water. And yes it is noisy. Dont buy this product.

We purchased our Maytag washer and dryer 5 years ago... THE ABSOLUTE WORSE PURCHASE... on average 3 repairs a year after the first 6 months!!! Now the dryer is down. It takes minimum 2 trips out from a repair company to fix even minor issues. We are going to Sears today to replace both units. PLEASE SAVE YOURSELF A HEADACHE AND DO NOT PURCHASE A MAYTAG! Yard Sales next step for our... cheap.

Almost one year to the date of purchase, my Maytag glass top range stopped working. The oven is still operational, but the range top does not work. The knobs turn and the surface lights go on but the elements no longer heat up. Trying to get a response from a real person at Maytag was impossible. I was put through a myriad of prompts that led me to scheduling a service appointment. I called AppliancesMart and got a wonderful sales person who said a service call would cost me 60 to 80 dollars and that he had not heard of repairs below $300 for this type of problem. Needless to say I am very angry and disappointed that I had not done more research before I purchased this item. If I can prevent one more person from making this same mistake, I will get some modicum of satisfaction out of this horrible experience.

We purchased a Maytag front load washing machine and dryer about 5 years ago. The front load washer is completely full of mold even though I have always followed the directions of wiping it out after each wash, leaving the door cracked, washing the machine with Affresh and even trying bleach and vinegar rinses. When I called customer service they refused to do anything about it. Then the dryer stopped working after 5 years and we had to get it serviced. Now, the door has completely come apart, as in every little piece has come off the handle and surrounding door frame. I have never seen anything like this on the oldest of machines and I have taken care of these appliances. I will never buy another Maytag...

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

So far, so very good. This is the first time owning/using an electric oven. I just love my Maytag. It was affordable, especially since it was a combo sale with the over-head matching microwave from Home Depot. Two years later and it's as if I just purchased it. Wonderful, wonderful, wonderful.

Have been very disappointed. The burners keep going out. The repairman said a bug could crawl on the element and break it. Then the temperature on burner on it works from med to high and any lower no heat. The dual burner is now backwards. The oven handle keeps falling off. Worst range I ever had and I thought it was a step up to Maytag.

Maytag Dishwashers work great. It cleans well and appearance is very good. I have always trusted Maytag appliances. Its quiet running and also energy saver. If I had to replace I would stay with Maytag.

Electronic control board fried after 3 yrs on Maytag Gemini range - certain buttons on control board would not set for ovens. Called Maytag, said was not covered, past 1 year warranty. Recommended repair shops, all overpriced. The piece cost between $300-500 for a 3 year old stove. Cheapest repairman wanted 90 to install piece. Ordered piece online and replaced it myself with help from YouTube video. Maytag has lousy repair records lately. Of 4 Maytag appliances purchased in 3 yr kitchen remodeling… already had issues with 3 of them. Do not recommend Maytag anymore!

In April 17, 2015, I purchased another Maytag microwave but wanted the convection oven too from Home Depot. The convection fan quit working in January 2017. I called Maytag to ask how this was covered. Maytag only has 1 year warranty on parts and labor. So basically if you dont buy an extended warranty, you are stuck with a product that quits working. Apparently, Maytags work is only good for 1 year or they would have a longer warranty. I told the Rep this when I spoke to him. He told me they normally last 5-7 years. Wow, still not acceptable. He said I had two options. Maytag could send out a repairman and it would cost almost $300. The other option was just as ridiculous. I told him I paid almost $500 to start with and it only lasted 21 months. Of course he said if I had bought extended warranty it would have helped. If I paid $500 for an oven, why should I have to pay more to cover their bad workmanship?!! I am very disappointed in the quality and price of this convection oven. The bad thing is I bought all new Maytag stainless steel appliances in 2016 to match the convection oven. The products I replaced had been in my home for 12 years with no problems.

We purchased a Maytag MFI2670XEW6 french door/Bottom freezer refrigerator in July of 2012 through Home Depot and for the past 6 months have had to scrape ice off the bottom of freezer every 5 days or so to prevent water flowing on floor. I see so many exact complaints from people that I am just fuming! Cannot believe this company is not backing their products up with that issue. A recall should most definitely been done. I grew up believing Maytag was top of the line but I am wrong. I bought this to replace a 16 year old GE refrigerator (side by side) which I never had any problem with and now I regret not replacing it with another GE. I havent contacted the company yet as I thought I would check complaint reviews before I did that but it seems that the company is just treating their customers like dirt. To spend $2200 for a refrigerator and have problems within the first 3 years is unacceptable!!! They had better start going good on this problem or face the fact that they will no longer be in business a short time down the road. The best form of advertising is word of mouth and online reviews and it looks like they are going to lose a lot of customers with the direction they are taking.

I, like SO many other people, am experiencing problems with a relatively new Maytag dishwasher. Mine is Model MDBH979SAB1. I have owned the dishwasher for 4 years but use it 6 months of the year and, because I live alone, maybe twice a week. In effect, it has the equivalent of less than a year of normal use. My problem is the same as countless other people. I can tell from how it behaves that it needs a new control board. I find little comfort in the fact that I one of several thousand people experiencing a problem with a newer Maytag appliance. What concerns me, after reading many negative reviews and seeing Maytags response, is that Maytag does not seem to care. We need to get the word out. We need a massive boycott of Maytag. We need to hit them where it hurts: in their bottom line. Since they seem to be content to continue to put out defective products, the only way to protect consumers is to put Maytag out of business.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

We loved the Maytag dishwasher when we first bought it. After about 5 years it started leaking. Had rubber gasket replace, only held up 2 years. This was the only problem.

Purchased Maytag washer 2014, first the porcelain in the tub chipped then 3 years later the control unit assembly and actuator went bad they wanted $464 to fix the machine, more than we paid for it. The dealer tried to sell us insurance for this product at a hefty price, I believe all manufacturers are making their products with a short lifespan and the way for them to make money is by not making a quality product like they used to do that lasted 25 years or more, the only washer out there that is dependable is speed queen made in the USA in Wisconsin.So we the consumers are the losers in buying washers that do not live up to their name, Maytag covers themselves by a warranty of one year period for parts and labor and if you do not buy the extended warranty at a hefty price you are out of luck - so my advice is when buying a washer read all the reviews and make your decision, but the best advice is buy a speed queen online for $600 and save $400 by doing that and get a quality washer that will last 25 years or more.

Double door Maytag 3 years old has been leaking water in freezer floor and forming sheet of ice. After reading the reviews, I may decide to buy a different brand. Why spend more money on repairs! Very bad experience!

About 9 yrs ago, we remodeled our house. And when it came to appliances, I was vehement we were going to go with Maytag because of their great name and reliability (We have 7 sons and needed reliable appliances). Boy, was I ever wrong?! We have gone through 2 Maytag dishwashers and countless repairs to the Maytag dryer. And our top of the line refrigerator has been a piece of junk!Of course, shortly after the year warranty was up, the flimsy pieces of plastic holding up the shelves started breaking off. The repairman, who came to replace the cooling coil on the refrigerator, said those shelf plugs couldnt be fixed. The whole front of all drawers have come off as well. He mentioned that Maytag was going bankrupt and started compromising on fit and finish. And he said that we just happened to purchase in that time frame. Now, we have a compressor that needs to be replaced for over $500! I have, in my garage, a Gibson freezer from my grandma that is 40 yrs old, and literally the most reliable appliance we have. Never have we made any repairs to it!I called Whirlpool (since they bought Maytag) to tell about my horrible experience with Maytag, and let them know we have to replace these appliances. I asked if there was anything they could/would do (discounts whatever) to redeem their name. I was told that they would not be able to help at all. So, I told them that I would not give Whirlpool anymore of my business and warn anyone I could, not to buy Maytag, Whirlpool or Amana. Isnt there any appliance company out there who cares about customer service, a good name and a reliable product?!

Purchased an over the cooktop microwave 3 years ago, it came with a 20 year warranty. It stopped working and I promptly emailed Maytag customer service. It took them over 3 weeks before they responded. That is not acceptable. Did they think I had a back-up microwave to take its place until they finally got around to reply to me? Well we could not wait, and we just threw that piece of junk out and had it replaced with a competitors unit. We will never buy Maytag again and will inform anyone we know about the poor operation of Maytag products and lousy customer service. My suggestion to anyone considering Maytag products is to not waste your time and money and look to another manufacturer.

The Maytag Bravos washing machine (Model No. MVWB75OWQ1 Type 580) is the worst Ive ever owned. The low water level obviously is not sufficient to clean the clothes as the clothes come out still dirty. I pre-treat stains carefully and follow all of the directions and 9 times out of 10, my clothes come out with the stain still there. The clothes never smell clean. In fact, they have an odor. My t-shirts still have a smell of BO under the arms and some of my clothes still smell like my perfume. They just arent clean. I feel like we put our dirty clothes in this machine and they agitate around in a little pool of water for an hour and they come out still dirty. The machine frequently gets off balance and shuts down too. If I had the money to trash this one and go buy another one - Id do it in a heartbeat. Unfortunately - Im stuck with this piece of junk until I can afford to buy a new one. This was a total waste of money and Maytag should be ashamed that they have not recalled it and given its customers a replacement option.

I purchased a Bravo 300 MVWB400VQ in 2009. I knew in 6 months that I had made a huge mistake. The clothes began coming out soaking wet - the dark clothes have lint, pet hair, and rings on them. The large capacity drum is just that... a big drum. If I wash bedding in it, it becomes off balance and sounds like its fallen over. I have used only HE detergents, and I wash the washer (yes, wash the washer, does that tell you anything?) before the light comes on. Now the machine sounds like its full of loose parts or rocks in it when it begins to fill up. Its even worse when the water starts to pump out. Now that Ive read all the other complaints, I realize that Im doomed. All of these trusting people have been cheated out of nearly a thousand dollars for a piece of junk. What good is Consumer Affairs if there is nothing done when there are so many complaints? I will join any lawsuit against Maytag if ever there is one. This is another lemon that promised everything and delivered nothing.

Maytag, Whirlpool, and Sears are junk dealers. We bought a Maytag Bravo topload washer in April 2011. Shortly after the first year, after using it once weekly, it began to stop draining. Clothes were soaked, meaning lots of wringing out by hand and using the dryer double time to get them dry. There are no clogs or kinks in the line. The machine is junk! It should have lasted much longer than this. I am not going to spend more money to have a repair person come and check on it. Its not worth it. Im going to buy a GE washer, the old-fashioned kind that gets clothes clean. Maytag, Whirlpool, and Sears are much worse-off breeds these days. They are off the list for good. Their products are a joke. Unfortunately, Im not laughing, but close to tears. Enjoy my money, you **.

I bought my maytag stove model MGR7662WS on January 30, 2011 and have had it serviced 3 times... same problem. I set oven to 350 degrees, put food in oven and later check on food only to find the temperature reads 350 but the oven is cold. Food is not cooked and it smells like gas. I turn it off and turn it back on and it does not turn on most of the time. Service guy keeps replacing parts and says he will replace the same part he just replaced last week. He says sometimes the part comes out defective. I think the stove is defective and I have thrown away so much food because it does not finish cooking and smells like gas. Its so frustrating because my Thanksgiving was ruined two years in a row due to turkey not cooking.

Im very pleased with both the washer and the dryer. The front-load washer is very efficient with many washing options dependent on items being washed. Spin cycle spins very well which lessens the dry time of the washer.

Maytag is the brand I had for 18 years and never had a problem with the washer or dryer in all that time. So when my dryer died I decided to get a new set of Maytag washer and dryer. I picked the set together and they dont have a lot of bells and whistles, simple to use and the washer is an HE. Cost was about $900 for the pair. I bought the washer and dryer in May of 2015. Models are simple to use. I have not had any problems and quite pleased with the work they do.I like to stick with a brand if it has served me well. Energy costs need to be low and I look for sales. Capacity is something I do not need a lot of, since it is just two I am washing for. Good quality is what I look for. I have not ever had paint chipping or rusting. Never had socks missing or a bad result with cleaning or drying. The washer has a cleaning cycle and the dryer is very easy to clean, the lint filter, and I get great results with no static when I take clothes out of the dryer.

The Maytag Bravos XL low water washing machine is very disappointing. About 20% of the time it needs a second rinse because there isnt enough water released to rinse clothing. Forget washing anything large. It just doesnt do it. Waste of money. The matching dryer is just fine - no complaints.

I purchased the washer 12 months ago. I liked large tub size and Maytag name. Thought I had made a good purchase. Boy am I am sorry. The washer overflows my large utility sink for drainage on large load setting and clean setting, ruining the flooring in an adjoining room. You cant wash black clothes in it leave white residue spots all over clothing. You cant use pod soap. Doesnt dissolve totally. Just on your clothing so you must wash again. So now I am trying to figure out what I can do but afraid I am going to replace it. Would Not recommend this product. Bravos XL MCT MVWB835DW1.

New side by side, water inlet to ice always freezes. Had a service man out, said some tube needed to be enlarged but still freezes up.The ice dispenser is total junk. Keeps spitting out ice after glass is removed and just a poor design. Dont recommend this brand.

I bought a Maytag Bravos top loader in Oct 2011. About a yr after having it, it started having problems. At the end of the cycle, theres still water in the tub and clothes are soaked. A couple of months after that, it started completely skipping the wash cycle, so the clothes would just sit in dirty water and do nothing. I called the small appliance co. I bought it from and by the time I get done paying a house call and parts, I might as well buy another one. I called Maytag because it seems theyre all having the same problem and at some point youd think they would be responsible for their product. They couldnt care less and the options they offered me were a joke!! Please, whatever you do, DO NOT BUY A MAYTAG because you will be on your own if anything goes wrong (unless you want to pay them the price of a new washer!!).

I purchased Maytag dishwasher Model #MDB7749SBW in November of 2013. The front touch panel no longer works. Everytime I push the selection for wash it automatically jumps to Cancel. This dishwasher is less than 2 years old. I didnt purchase the extended warranty simply because I thought I was purchasing a very reliable product. Lonely Maytag Repairman of old. Ha Ha. I am very disappointed and am telling friends about this and all of the reviews Ive read that are similar complaints. I would never purchase a Maytag product again.

MHW7100DW Maytag Washer Steam & YMED7100DW Maytag Dryer Steam. Both of them are easy to use. They hold lots of clothing as well as bedding and many different settings. They both do an excellent job. Brand and excellent reputation. Had my last Maytag washer & dryer over 25-years and had no problems with either. Thats why I bought Maytag again. Repairs are very costly when you have to pay technicians. Dont like poor quality construction or enamel chipping when you place items on them. Very easy to clean both of them. Practically no lint dust emitted into the room from the dryer. Had no problems with my previous washer & dryer. Thats why I purchased a full size Maytag washer and dryer again.

If I want to line dry something, first I have to pick off all the lint. Even when I use the dryer, I still have to pick off lint and there’s often creases with dirt dried right in. I have to inspect everything that comes out of the washer to see if it is clean before I dry it. This doesn’t save water, as I often have to wash things at least twice. Awful! Also, ridiculous. A wash machine is supposed to get things clean.

We bought a washer & dryer from Home Depot 2 1/2 years ago. The control board went out on my washer. I called Maytag and they wanted $109 for a diagnostic fee and wouldnt tell me how much the labor would be. A control board costs $350. So by the time all is said and done... the money would be better spent buying a new one. Maytags slogan of dependability lasts is a bunch of hooey. Washers should last more than 2 1/2 years and Maytag should back up their appliances. They just lost a customer.

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

This happens to be a commercial one - I dont know why; the landlord bought it. It will not do just 1 or 2 items. I would need this for when I have a very muddy towel from the dog & dont want to put anything else in with it; or with a newly purchased item that I want to wash by itself. It gets stuck on the wash cycle & will not continue. Then I have an item(s) that is soaking wet, which I dont want to put into the dryer. And in the winter, I cant put it outside. I did an online chat about this & was told not to just put one or 2 items in the washer. What??? Im 68 years old; have been doing wash for well over 50 years & have NEVER had this problem. I dont know if this applies to all Maytags since this is the only one Ive ever had, but I would definitely not recommend this product!!!

This has been the worst washer I ever bought. First the washer does not fill with water even on the deep fill function. It pours little water and washes the clothes with basically no water. The sensor for the lid broke less than six months of using it, soap residue is left on the clothes. I do not recommend this washer at all.

Bought this Bravo washer from a Sears Outlet Store. Had trouble the first 2 weeks and did all the troubleshooting to no avail. Just when I was ready to return it to the store I decided to try one more thing. The guys who hooked it up had reversed the water hoses - cold was hooked up to the hot intake, and hot water was hooked up to the cold intake. Took all of 5 minutes to switch the hoses to the correct intake and the machine works like a charm. MAKE SURE THE WATER IS HOOKED UP CORRECTLY.

I have always hated soft touch control panels so I purchased a Maytag Dishwasher with old style push buttons. IT DID NOT CLEAN THE DISHES, so Lowes took it back and I was convinced to UPGRADE to an MDB7749SBB0 and was told this machine was top of the line, although it was VERY temperamental from the start. I guess I should have done my homework. I see now several complaints about the control panels not working. I was told that MAYTAG was a very reputable company and that they stand behind their product. WRONG!. The company KNOWS these panels have problems and should replace them free of charge as it is obviously a defect. Nope, first they offer to send someone out (In a week) to repair it at $80 just to look at it and the panel is over $100 to replace, and when I complained they tried to sell me extra coverage for $250. REALLY? What is the purpose of purchasing a QUALITY dishwasher? I might as well purchase a cheap dishwasher and replace it when it breaks. I think you should be responsible for your product when you have several complaints on a specific part.

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

I had a problem with my 1 year old oven. I scheduled an appointment and no one showed up. So I fixed it myself. A week later they called to schedule an appointment and I told them that they were scheduled for last week. So their response was OK, I dont need them anymore - goodbye. The parts are under warranty so I send them the part I replaced myself and the invoice for the cost. I didnt get a response. So 3 months later I send a second letter. Three more months and still no response. I can remember when Maytag had commercials showing their repair sleeping because they had no work to do. Now, their products are failing and their entire service depart is asleep.

DO NOT BUY Whirlpool Corp Appliances, ESPECIALLY MAYTAG. They do not stand behind the units they sell. We dropped $600 on this Commercial Grade wash machine (5.3 cu. ft. High-Efficiency White Top Load Washing Machine with Deep Clean Option, ENERGY STAR Model MVW7232HW) and paid to upgrade the lines to stainless steel. It died after 22 months, a bad seal leaked water internally, fried some components (no water ever leaked from the unit onto the floor) and despite there being a 10-year limited manufacturer warranty on parts sticker on the unit... the fine print says only the tub and motor are covered.There is no way we could have known the seal was leaking and it was not the result of misuse (overloading) or abuse. The parts to fix it are back-ordered months and cost more than a new unit after install. Glad I paid $150 to learn all this. It also did not wash great on most settings. Purchased at Home Depot, they refused to stand behind the product as well.

Purchase a Maytag washer in 2012 and less than 4 years later have to go shopping for a new washer. Purchased a Maytag because was under the impression that it was a good product and would last. Not true. The washer almost caught fire, just happen to be nearby when smoke started coming out from behind the washer, so I was able to turn off the machine and then unplug it and my husband smelt wires burning. If I hadnt been nearby we could have had a fire instead of smoke. I dont want to rain on anyone parade but I wont be recommending this product to anyone.

Brand New 2017 Maytag Dishwasher MOB8959SFZ4 - The first time we used it it leaked from the door. I called the plumber back to make sure it was level and lined up properly and it was. Called the dealer, they sent a technician who sent away for a new latching mechanism. 3 weeks later the parts showed up. Technician installed them ran it through empty and no leaks problem solved? Nope. So I loaded it up and ran it again and it leaked. Called the dealer back but the technician is away on vacation.They suggested that the top rack might be pushing against the door for some reason when it is loaded so I removed everything from the dishwasher and ran it through again but it leaked again.Its something to do with the door not latching properly and it doesnt have a lever that locks like the old ones did. Its such a flimsy product. It baffles me that importers are getting away with bringing this crap into the country. Im now in week 5 with a brand new dishwasher that doesnt work. Maybe thats why its known for being one of the quietest dishwashers on the market.

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

Recently purchased a washer from Home Depot. Machine is now on its 3rd repair. The wiring harness is fired. Could have caused a fire. Now they still will not replace and part is on order which will take 4 weeks to be in stock. I called Maytag and expressed my concerns to which they could not help me as every washer is theirs can be repaired. I really don’t understand what happened to making things right. Very frustrated that they will not repair or reimburse for that matter. Please refund my mom and pick it up.

Im totally done with the Maytag brand that Ive trusted for over 30 years. I never knew until yesterday via Facebook friends that they are not true Maytag-made anymore. They were bought out by Whirlpool eight years ago. I bought my top-load Maytag Bravo 400 Series Washer ($1,028) at Home Depot in October 2008. No problems with it until now, less than 4 years old with error code DL. So I looked in the book and found it was the lid lock (the little red light wasnt lighting up when closing the lid, which prevents it from running).I made an online appointment with Sears Home Appliance repair to check it out. But after talking with online friends and googling fix videos, I was able to get it running today by taking the top off, unplugging the lid wire and plugging it back in. So far, its working but now I will fear each time I go to use it that something else will fail. My old Maytags (washer and dryer) bought in the 80s never needed service until they approached the 14- to 15-year mark. That only tells me that the newer made appliances are total junk! So many complaints and how the companies dont back their appliances, it just sickens me.

My Maytag dishwasher will not come on and it is loaded. The control panel is out for the third time.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

We purchased a Neptune washer/dryer combination with pedestals a few years ago. The washer vibrates so violently that I had to block it between the dryer and wall to keep it from walking across the floor during the spin cycle. We had a technician come out, and he stated that the unit just needed to be balanced. The level I used showed the washer balanced in all 4 directions. Then he said I had to balance it with the machine running to stop the vibration. That didnt work either. I had previously installed vibration dampers and the technician told me that makes the vibration worse. When is someone going to file another class action lawsuit against Maytag, as there appears to be thousands of complaints for this same washer?

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

Less than 2 yrs old and starts giving UL error on spin cycle. I try replacing the springs. No relief. Notice dark brown fluid under dryer. Thing sound like a plane taking off. A little more research and Im thinking its the bearings. Looks like an expensive repair, now I have to decide whether to cut my losses. Seriously? The reviews on here are just horrible, not like this was an dl hell machine.

I purchased this dishwasher at least 12 years ago and it still works. However, after that much use some of the buttons no longer work. It has china, economy, regular, rinse only and extreme wash features.

Not only does the water not drain properly causing an insane amount of stench of moldy water being trapped, but this washer has had nothing but problems since we got it. Error code after error code, problem after problem. So disappointed. My husband wanted an LG and I said it had to be Maytag because Maytag was the best. Thanks for making me a liar Maytag!

I purchased a Maytag gas range after remodeling my kitchen. I thought I was getting a good product, boy was I wrong. The ceramic gas grates are so slippery that pots tend to slide off but the real problem is that the racks inside the oven fall when you place pots on them. I tried cooking a Thanksgiving turkey in it and the racks fell to the bottom of the oven. It appears that the top rack and the bottom rack are the only two that stay in place. And it also appears that when the oven is on, the sides of the oven expand so that the racks fall. I have tried to contact Sears as thats where it was purchased to no avail. I will now attempt to contact Maytag directly but it appears that I will also not get anywhere there. I have read at least one other complaint of this exact same type happening to someone else. This is very dangerous. Do they really want a lawsuit?

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

Unless you’re doing laundry for an army don’t buy the Maytag commercial washer MVWP575GW. I should have gone with my original choice but my husband was concerned with the durability and warranty hence why we purchased this washer. It’s just the 2 of us and I frequently use the delicate cycle. Unknown to me at the time you can not adjust your water level so if you’re washing delicates plan on wasting a lot of water unless you only wash your delicates once a month. In my opinion delicates are undergarments, blouses, etc. delicate cycle in “deep water wash” only. As far as we can tell the wash cycle at its longest is 8 minutes which I guess for commercial grade is probably correct. However there is a presoak option that I don’t the believe does the work of a longer wash cycle. If you have to do a quick scrub on a piece of clothing as the washer is filling up you can not do this as everything stops once the lid is up.Last but not least the washer is loud it sounds like it’s going to break down at any minute. I’m sure many of the issues people have with products today are due to government regulations. I’ve tried contacting Maytag customer service on numerous occasions to see if I’ve been doing something wrong even though I’ve read through the operating manual several times, I’m currently on hold for 20 minutes. Doing the laundry has never been the highlight of my day but I never minded it until now. I absolutely dread it now. My suggestion would be if you like the features on your current washer, spend what you need to to get it working properly which is what I wish I had done with my 23 yr old washer. Worst purchase I’ve ever made!

My old Maytag is still working after 20 years but my husband surprised me with a new pair! Washers is just pure junk. Not enough water to hardly wet the clothes. They just rub together and get worn out looking, towels are rough and not soft but my biggest complaint is the AWFUL wrinkles! I have to iron everything! Only had it 3 days, called Menards and asked if we could return for an exchange or upgrade and they said no. If this is the best American Made has to offer, then I will look at the Samsung! Shame on you Maytag. Not one good review on here and you do nothing to restore confidence in American Made. I will spread the word - NEVER by a Maytag or an appliance from Menards. Neither one stands behind the piece of junk!

I purchased a new Maytag top loader at Home Depot. They delivered and set up. From the first load, I have had problems with the washer stopping and jerking. Clothing becomes a tangled mess. I contacted Maytag, they suggested I make sure I put on proper setting for the items within the washer. I do not know how one can fail at putting sheets in the washer and putting the setting on sheets and they are so twisted you have to spend time pulling them apart. This happens to almost everything I wash. I believe that I have a lemon, still under warranty, Maytag believes I should pay for a house call. Home Depot will only forward the information to me that Maytag gives to them.

Purchased this Maytag microwave brand new on April 2017. In January 2019 began to have issues with the display reading open/close door. Maytag would send a repairman for $160 to take a look at the problem. Parts of course are extra. I will never buy a Maytag product again.

We purchased a Maytag Bravo in 2011. With only three adults in the house using it for regular clothes washing, we were surprised when we had to call a repairman and the charge was going to be over $500 to fix the transmission and clutch. We had the same problem as described in many of the other comments, i.e., door sensor would not work properly and machine would not spin. Not even worth it to fix. Word is that Maytag is made by Whirlpool and if this is true, it would explain the disappointment. We have replaced more Whirlpool appliances than I can count. Never again Maytag!