We bought the Maytag Bravos washer & dryer combo from box store. I wanted an extra large capacity washer to accommodate king sized bedding, and having fewer wash loads in general. Cons: 1 - This machine is not energy efficient when each wash load takes 1:30 to 1:50 each load. 2 - The detergent/fabric softener/oxi dispensers are a joke. Water dumps into every compartment at once. And if there’s still detergent left by the rinse cycle, well you get the picture.3 - The “Bedding” setting is the only one which will provide enough water in the tub to get anything wet. Since there isn’t any type of agitator the clothing/bedding just floats on the surface in dirty perfumed water. 4 - With any of the other settings the water level is so low it doesn’t always get everything wet so items are not being washed properly. At most maybe 2 pairs of jeans or just a few t-shirts can be washed on the “Normal” or “Power Wash” settings. 5 - Because there isn’t an agitator, clothing gets knotted up. Dress shirts, dress pants, jeans, towels, you name it, everything comes out of the washer in a knotted mess.The Bravos XL Dryer: My only complaint with the dryer is that it allows a good amount of lint to pass through into the machine. Then it’s difficult to get any type of lint brush into the vent area to remove the lint. Dampened lint in the machine can make clothing smell musty and nasty. I had to call a service to remove lint from the dryer & ducting because of the odor lingering from the inside the dryer.

I love my dishwasher. The only hold back is similar to what I hear about all others and that is that it takes a long time. I love that is it quiet, has lots of room and is easy to use.

Washer needs new transmission at only 3 years old! Maytags 10 year part replacement doesnt cover it. The company actually asked why I didnt purchase extended warranty, I thought I didnt need one. Bad bearings, it doesnt wash the clothes clean, $400 to fix it. Needless to say Im buying a new washer and it will not be a Maytag, worthless piece of scrap!

This washer does not distribute enough water to wash clothes properly. I continually take clothes out of washer that are not completely wet. My darker clothes have white spots of detergent on them that did not get rinsed off. This product should be pulled from the stores. We have tried everything, using deep water wash, bedding wash, to get more water in the machine. Our clothes are not coming out clean. Complete waste of our money!

I bought a full Maytag kitchen in 2010 because like many others, I trusted the brand. However, before I knew it, the dishwasher broke down. I live in Canada so I get Whirlpool (owns Maytag) 2 year limited warranty. Thank God for that because I have had the repair guy come 7 times. Each time for the same problem (control board) and they have replaced a listed of parts with no success. I have asked them to honor their no lemon policy but am given excuses as to why someone has to come see it first before they can give me a new one. Once the service guy arrived he obviously has no idea about anything and just goes for the repair. Its so frustrating.I am fed up. It is completely unacceptable because now Im losing money staying home waiting for the repair guy. Maytag is the biggest piece of junk I have ever bought. I only hope you see this before buying a Maytag product. Like many others here I use my dishwashers once a week. Now Im faced with a dilemma where I might have to purchase a new dishwasher as soon as my 2 year warranty runs out. My $700 went down the drain.

The bearings and motor went out in less than 3 years. The warranty good - the dealer I purchased from Siano Appliance gave me credit to purchase another Maytag washer - which I had to purchase an additional warranty for $320. The new Maytag is less than 5 months old - the motor has been replaced and waiting on a tech now to fix it. It would not come on. SO in warranties I have paid over $640 and am still having issues with the new washer. The first time I purchased a warranty for 10 year - when the machine was replaced I had to purchase another warranty for that machine - now if I have to replaced this one that will be an additional $320. IS this legal?

We have a Maytag Dishwasher Model MDBH949AWB. We have purchased the extended warranty. Today, after more than 100 minutes on the phone, mostly on hold, we were unable to schedule an appointment to replace the control board, or even have them verify that we have extended warranty coverage. It generally took many many minutes to get a person, only to be referred to a different person at a different number. Nobody had access to our extended warranty info, and to go further into getting a repair scheduled, they said they needed that info. I finally went on their website, and after keying in extensive information, I got a screen saying they were having trouble with their website, and to please try again later. So I did their chat, and ultimately they told me to call 866-730-6094. The earlier numbers I called, in sequence, were 866-576-1660 (53 minutes on hold); then told to call 866-265-0029, for another long hold. And then told to call 800-626-4342. Long hold, and I hung up. At one point, I think the second person I actually spoke with gave me an incident number of **. My extended warranty expires in Feb. of 2017, and they even asked me to renew early. Since the warranty seems totally worthless, why would I do that? Terrible customer service. Wont do business with Maytag ever again, and am warning others not do so either.

Our Maytag Atlantis dryer had smoke coming out and almost had our house on fire! Had it not for us double checking the entire house would have burnt down! The dryer is less than 10 years old and already it is tearing apart. I cant risk using it again. Terrible company. I would never buy Maytag products ever again!

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

CONSUMER BEWARE! The Maytag Bravos X is without equal the biggest disappointment I have ever had the frustration of using. What a rip off! Water goes in, water goes out and it makes A LOT of noise. That’s it! (That locking lid should have been our first clue.) Specifically, a normal load takes one hour. What you save in water you pay double for in electricity. If you place a folded pair of pants in the washer that’s the way they come out; folded. Two twin sheets and a small blanket come out of the washer with dry spots every single time. If I use liquid fabric softener the clothes come out spotted with it. And it is louder than the train. You would be 100x better off purchasing a washer at a yard sale for $25 than to throw your money away on the Maytag Bravos X. DON’T DO IT.

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

We owned the washer for 2 years and 2 days when we got a code F70. After searching online, I found hundreds, if not thousands, of reviews and self-help forums that show this product is in dire need of a recall. The problem I had is the motor control unit (MCU), which is a $225 to $275 part online. However, Maytag will only replace the board under extended warranty with a refurbished board that they say costs $330, whereas they say the new one is over $600. Why is it that Maytag charges double what everyone else charges? If so many people are having these problems, it is obviously a defect and should not be the consumer’s responsibility. It is obvious that this is too common of a problem.

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

Bought a Maytag Front Load MHW6000AW washer and had a problem with amount of water in wash cycle. Dealer sent service men 3 times and changed several parts but washer still did not work and both repairmen said they did not know what was wrong. They called Maytag Tech Support but those people did not listen and said if no code shows up the machine is operating properly. Maytag then sent another company repairman. He worked 2 hours and said he could not find the trouble and Maytag support hung up on him. Maytag then sent another company repairman and he did one test and said the machine is fine and left in about 15 minutes total time. Now Maytag refuses to send another company for another opinion but I have a $1200 machine that still does not work properly. I am totally dissatisfied with Maytag and will stay away from their products totally. Companies wonder why people buy foreign equipment and this is the answer. I had a Samsung washer and never had one bit of trouble with it.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

18 month old range did not shut off although it showed off on the cancel page. $800 down the toilet. Maytag had the guts to charge $100 to troubleshoot plus parts and labor. I will donate it to scrap metal. Company does not give a rats behind. DO NOT BUY MAYTAG.

Original owner of $800 HE top loader washer since 2010. We heard a grinding noise for months, then finally it seized up. Repairman quoted me $300 to replace bearings. The repair guy seemed a bit too eager for the job, so I knew it must have been easier than expected. I Googled the heck out of it, and used this forum heavily for guidance. Seems the bearing failure is a pattern issue. It also seemed ridiculously involved and no one had posted a how to video matching my model’s layout. I took a peek with my own eyes and noticed a sock had gotten under the basket. The sock got caught in the drive belt and knocked everything loose. I removed the debris, tightened the pulley and everything worked. Cost me $0 to fix myself. So buyers beware before repair. And check the error codes yourself when in doubt! The first thing I did was check error codes. Found a great video here **.

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

Maytag Dishwashers work great. It cleans well and appearance is very good. I have always trusted Maytag appliances. Its quiet running and also energy saver. If I had to replace I would stay with Maytag.

Save money. I have always had Maytag & loved them until I bought the Bravos xl top load washer. The salesperson insisted it was a large capacity energy efficient w/ great maintenance record -- greatly misleading. The water level does not rise enough to effectively clean or rinse so clothes do not get cleaned or detergent doesnt rinse out thus allowing only 2 to 3 towels or jeans to wash per load. Such ineffective cleaning cycles create the ongoing need for loads to be rewashed and be extremely small, yielding credence to other consumers’ accusations of being mislead and false advertising of xl capacity. As such, it takes hours to wash a family of threes clothes. The machine shakes like crazy and clothes get ruined as they get twisted and tangled into each other ripping, tearing, misshaping and ruining them.

We purchased a Maytag brand thinking it would be a quality long lasting machine. Wrong, the washer shakes from day one, We complained to Lowes, they brought out and installed a second unit, it does the same. The clothes dont get clean, sometimes you can see the blue HE Tide still on the clothes (sheets) after cycle is complete. Junk, waste of money, Ill never buy another Maytag product again. Dont waste your money on a Bravos Maytag top loading HE machine.

My front load Kenmore just fell apart. I guess Im lucky I have had it for 8 years and now its broke. I could fix it but thought it would be better to get a new one. I looked at all the reviews for front load washer and could not find one that had positive reviews. So I went with a top load. After reading all the complaints I might have made a mistake, but its too late now as it was delivered yesterday and now doing the clean cycle. Oh my…what junk they all produce now - a true throwaway society. My refrigerator is still working after 24 years what a gem of a product. Happy days.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

The washer is not cleaning the laundry. Its a HE my butt. Its been looked at and fixed numerous times. It sits too long and it doesnt really agitate the laundry at all. Laundry is in the exact position when you loaded it when its done. Its the worst washer ever! I can clean the laundry better in the sink!

I have owned my Maytag Neptune Washer since 1998 and this is the first time that it will not drain all the water... Doing some research before I call a repairman... Have a Great day!

I bought a Maytag refrigerator over the summer - the French door and drawer freezer. Expensive but crappy. After about a month motor starting making noise then is shut down. Called the store. They came and swapped it out and not even two weeks later same thing. Looked up product and all awful reviews. Never thought to look up reviews before purchasing. Could of save myself the headache. Not to mention my daughter was like, Mom stop buying that brand. It sucks. Did you not realize our washing machine is the same brand and after almost two years it started acting up and your last washing machine you had for 10 years before it even gave you any problems.

Bought Maytag Bravos in 2010. It does not clean but worse than that it rips clothing (for example: loops off pants, holes in pjs, tons of ripped towels), so many items of clothing torn that I cant keep count. Today I had a pillow case ripped apart (see image). I have had four sheets ripped that I can no longer use. Maytag should have recalled this washing machine. I have the Maytag Bravos dryer also and the drum was on backwards on it when I bought it.

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

Maytag Free Standing 30-inch Gas Range - In 2004 we bought our model MGR5775QDS gas range with 5-burners because it offered the most BTU variety for the price: 1 burner with a high BTU (16K), 1 with low (5K), plus 2 in mid-range (9.5K) and 1 with 12K. Within half a year of using the oven, we turned on the self-cleaning function. Big mistake. One cleaning cycle later, our oven refused to ignite. The cleaning cycle burned out the ignition unit. Cant remember if its replacement then was under warranty but the repairman said this was a COMMON PROBLEM with Maytag and we best not use it EVER. In 2014 our cleaning lady mistakenly thinking she was doing us a favor, set the self-cleaning function. Once again, the ignition unit was destroyed. This time its replacement was $350 with part and labor. One and half months later, the oven is again non-functioning. This time our repair guy said the part is a very minor, inexpensive one BUT MAYTAG IS NO LONGER MAKING IT!!! The only way well get our oven back is if he can find another model and cannibalize it to fix ours. Are we disgruntled? Yes. Would we like to see a class action suit against Maytag for knowingly manufacturing a gas range with a malfunctioning self-cleaning unit that destroys oven parts? Yes. Will we ever again buy Maytag? Not on your life. A once stellar manufacturer gone down the tubes with a growing reputation for making junk. American-made appliances mean zip these days. Thank you for nothing, Maytag.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

Really havent had any problems. The Maytag repairman really is lonely. Great quality wash machines and dryers for that matter. I havent had to do anything. Spins well... Very quiet, no complaints. Dryer works well too. Many cycles area to put fabric softener and bleach. It has a extra extraction cycle and many other features.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

This washer is a piece of expensive junk. It was used sparingly (2 people using it) for 16 months when a repair service had to be called. The estimate to fix the machine ($980) exceeded the initial cost. It did not clean the clothes adequately when it was working. There was a powdery substance on the clothes when they were removed. The clothes were always bunched up and intertwined. Only the proper type and amount of soap was used. I cant recommend this washer to anyone. We were very disappointed since we have always purchased Maytag washers/dryers. Never again.

My Maytag dishwasher is a nightmare. I purchased it in February 2013, started having problems with it turning off a week ago. I called Maytag customer service on Wednesday and was told I had a service call scheduled for Friday. I took the day off of work to be available for the repair service. I was given a phone number for the repair service. By noon I was wondering when I would receive a phone call to let me know when the technician would arrive? Then I was told that my appointment was scheduled for next Tuesday... ARE YOU KIDDING???? THAT WOMEN FROM MAYTAG CUSTOMER SERVICE LIED TO ME ABOUT THE DATE OF SERVICE!!!! I spoke with Scott, customer service representative (manager) and he told me that I was sent an email with confirmation. ANOTHER LIE!!!! I HAVE NOT RECEIVED ANY EMAIL FROM MAYTAG. I would never buy another Maytag appliance.... They DO NOT STAND BEHIND THEIR PRODUCTS. LOUSY CUSTOMER SERVICE... SUB PAR TO SAY THE LEAST!!! Very dissatisfied customer - wasted my time and are not willing to make it right.

Purchased a Maytag Dishwasher (Model MDB7749SBBO), total with tax $590.34 on 3/31/13. It wasnt a cheaper model, had stainless interior. Owning it after a 1-1/2 year, the Control Panel went bad. Maytag offered me for $267 for repairs and 1 yr warranty. Why thats about half the price I paid. My personal repairman told me the cost would be around $200 to replace the control panel. Why I could get a more inexpensive model for $300 and still get a year warranty. Very disappointed in Maytag quality of their product.

We bought our set when they first came out at Home Depot. We gave a pretty penny for the set. The first complaint was soon after I got them home; the washer gets the clothes so tangled up its hard to get them out sometimes. The 2nd complaint is, for a couple months now, the UL light comes on and beeps. I have to open the lid, close it and it starts that part of the cycle over and it usually does 4 to 5 times before it actually spins and finishes. I put it in the shop; they said they cant find out whats wrong with it. They said the leveling rods are still new looking. I was like, I know its still a newer set. Its money for nothing. I called Maytag. They want to charge me over a $100 just to come out! Rip off! Do not buy this set. Beware! Im still having problems. I will not buy a new Whirlpool set because they bought Maytag out and I will not buy a new Maytag set ever again!

The Maytag has nice features but the shelves dont allow much room to adjust them and the freezer could stand to be a bit larger but overall its a good and hard working fridge for the price. Would love if those two things could be fixed without a huge price tag.

Maytag Dishwasher purchased for $634 on 7-6-12 from Lowes. Control panel malfunctioned in August 2014. Started leaking in April 2012. From the online comments, I am trashing this machine. It is not worth fixing it and having it malfunction again. Maytag will not say anything about this, only offers a repair person out to fix. I am very disappointed that my hard earned money purchased a sub standard machine. Maytag used to mean reliability. NO more.

This washing machine is garbage! We paid almost 1000$ for it and it damaged most of our clothes. We believe this washer was released from Maytag with a functional problem. Because it does not drain the water and soap properly, therefore it leaves white stains on the clothes after it is done. Please see in the picture. After recommendation from Lowes we clean washed with Affresh for many times, it did not fix the issue! We called Maytag customer warranty service. They sent a technician and his solution did not solve our problem. We called them again and they said if they send a technician again they might charge us 130$. We think Maytag warranty is a waste of time and energy. They are useless. We will never ever buy anything from Maytag.

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

Maytag french door fridge model MFF2558VEW7. I bought this fridge about 3 years ago. Have had nothing but problems. First I had problems with the freezer frosting up, then I had the same problem of ice buildup in bottom of freezer. Now the freezer only gets cold enough to cool drinks and the fridge only gets to about 60 degrees. This is not the only Maytag appliance I have had problems with. I bought a dishwasher a few years ago that quit working just after the warranty ran out. Both bought from Home Depot. After reading other reviews, it seems that appliances bought from Home Depot have had problems too.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

The design capacity of the dishwasher is not conducive to cleaning a full load. Within 3 months of purchase one of the interior baskets broke. I will never buy another Maytag product again. I was a fool in believing this was a top of the line dishwasher.

I have had 2 Maytag washers in 37 yrs and loved their products, however I purchased a Maytag quiet 300 in 2/09 and it is the worse Maytag product on the market. The frame around the bleach dispenser has rusted out and I have called for the 3rd time in 5 years to have it repaired. To my dismay it will cost 300.00 to fix because the bearings have to be replaced. I will now have to purchase a new washer. The days of the Maytag man are long gone. By the way the Maytag dryer has been serviced twice. I thank God everyday for that extended warranty I bought, but now it has now expired.

The machine started having issues within a week of purchase. The current issue is, when running the clean cycle, the washer becomes stuck in a mode where it is constantly adding and duping water down the drain. First time it happened, I started the clean cycle before going to bed. In the morning the machine was still in the clean cycle. Running water in the tub and pumping back out down the drain. The water heater ran all night, as the washer was filling and draining the tub at the same time. Each time we attempt run the clean cycle, the washer locks up in this mode.This is the only issue I have had. Many people complain about wrinkled clothes and I agree. I take each garment out the washer and shake it out before putting it in the dryer, this makes a huge difference. Just remember, this is not your mothers washer. It does a great job at cleaning the clothes and saves many gallons of water a month.

We have had this dishwasher [Model MDB7749SBW2] for about 1 1/2 years now, and gave had a lot of trouble with it. It will run a cycle on its own without anyone even touching a button. My current problem is the start button wont work. I reset the dishwasher by pushing the series of buttons I found online to do a reset, and the start light lit up, but after the reset cycle was finished I tried to run a wash cycle and couldnt get the start button to do anything. Ive seen a lot of reviews online on this being common with Maytag brand dishwashers this old. I will NEVER buy a Maytag product again nor would I recommend it to anyone as a good product. I am very frustrated and disappointed in Maytag!!!

No motor is available for the Bravos washer machine which is 5 years old! Now the machine is garbage and I need to buy a new one. I thought Maytag was a great brand so I purchased the Bravos but now I understand from the company that no motor replacements are available!! Wtf? Maytag/Whirlpool dont care for loyal supporters so, I am TELLING EVERYONE not to purchase Maytag/Whirlpool appliances whose name has gone for a dump with this latest situation.

Fire Danger. We had a power outage and my Maytag gas range/double oven (Model: MGR6875ADS) was dead after the power came back on. We figured it was the control board and braced for the expense to replace it. A few days later, I plugged the oven back in just to see if it would work and it did! The control panel came back on and we were up and running. The good news end there. On Christmas Eve, we came home to a house full of smoke with fire alarms buzzing. A butcher block style cutting board that was on top of the range with Santas cookies on it was on fire. Twenty more minutes and the house would have been gone.

I purchased a washer in July and its already off track. When I seen it I know it was junk but the sales person assured me it was a good product. 3 months later its off track. No spinning. DO NOT WASTE YOUR MONEY.

Warranty dept. will not help you! I have been told by technicians sent to service my refrigerator after it spoiled food multiple times from not staying cold. The technician flat out told me that this refrigerator cannot be fixed but they are not allowed to say that it cannot be fixed. They will not return your calls and are just flat out rude. After asking to escalate a call, the rep said the manager will call me right back in a few minutes. Hours went by and I called again five minutes before they closed to speak to someone in management at that moment. This manager told me with no hesitation that they dont always believe what their technicians say because they send out techs that are good, okay, and not good. My first question is why is Maytag confident in the people they are sending to my house time and time again that stay for three hours?! She began to get rude and disrespectful and said, Well, if you had cancer, you wouldnt believe the first thing they say... I am in awe of these remarks. How do you compare a refrigerator to cancer?! I asked for a business address and stated that I would like the address to file with the Better Business Bureau and she told me that they have all the info I need. She refused to let me speak to anyone else. This situation is uncalled for when I have the technician telling me, This refrigerator is not repairable but they wont allow me to say that and Maytag will not make this an easy process for you. Unbelievable!

Just like all the other reviews, 14 months after purchase and 2 months out of warranty the control panel on our Maytag Dishwasher stopped functioning. The “10 year warranty” is a joke a covers 3 things. We had model MDB4949SHX, $550 new.

Gemini Twin natural gas range - I bought this range approximately 18 months ago. I thought it had all the features I needed and it looked good -- looking good is just about all it does! If you are a real cook I would suggest you avoid this range. The burner controls are preset and it is impossible to turn the flame very low if a simmering heat is required. If you are making meringues, again, the oven heat cannot be turned to a cool enough temperature. Ovens bake/broil unevenly. It takes forever to bring a pot of water to a boil, not because the flame is not hot enough, but because the pots sit far too high above the flame. Bad, bad design. Probably designed by someone who eats take-out!!

I purchased this washing machine from Home Depot in 2012. I am amazed that it lasted this long after reading the reviews on here. It will not drain water, it will not spin. I see many customers bought the same washer and are having multiple issues. When will Maytag recall these machines? Overpriced and unfair to consumers to sell something that is broken or not reliable.

Our oven is 3 years old and the last time I used the self clean option caused the control panel to malfunction. Now we have to buy a new panel. The repair guy online advises people not to use the self clean as this is a common problem!!! What? I cant use that feature? That is so ridiculous!!! Now we have to pay $300. Whatever happened to the Maytag claim to quality and you would never see a Maytag repair man? Something needs to be done about the problem of appliances and electronics being so poorly made and basically disposable.

My $1500 2 yr old Maytag mbf2258Dem refrigerator stopped cooling properly (wont freeze). The icemaker was the slowest I have ever had. That may have been the problem when I bought it. The Maytag Repairman came out and said that even with Maytag sending me a new compressor (under warranty) this unit was not worth fixing. I called Maytag and they said sorry there was nothing they would do. So l looked up every review I could find... and this refrigerator is just bad. Not Worth Fixing. So Maytag deceived me. On the front of the door it says 10 year compressor warranty. Thats a big sales feature! They know that they have a problem. This is one bad company!

Maytag dishwasher does not clean dishes. It has hot water and we have had a repairman look at it and he said water jets working. We have to wash all our dishes by hand before loading them into the dishwasher to sanitize.

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

This Maytag Bravos HE machine has the poorest design! It doesnt use enough water on the normal cycle so I always have to use the bulky load just to get the clothes wet. The old washers used to spin the water out thus keeping the load even. This machine drains the water first and then tries to spin an uneven load! When this happens the machine bangs loudly from side to side, stops, refills with more water and starts the whole process again until it fixes its problem or until you go shake out the entire load and reposition everything. Then it uses more water to start the process all over again. It takes twice as long to do a load of laundry.Every time I use it I say I hate this machine! This machine should have never been released without extensive testing. Maytag could have figured out all of their own problems and fixed them so we wouldnt be writing all of these bad reviews. A recall should have been done years ago and the problems all fixed. I will never buy Maytag again!

After 16 months my Maytag dishwasher control panel went bad. The company told me they could not help me. I asked for a new control panel to install myself, no luck. I bit the bullet and bought one online for 110 dollars. 2 months later... you guessed it, its bad. Now I have to send it back under warranty. It was a Maytag name brand OEM part. I thought Maytag was a reliable name, I thought wrong. Never again.

Maytag MHWE450 washer - Purchased this front load washer/Dryer and pedestals 12-1-2011. The bearings are so loud when it spins that you cant hear anything. You have to replace the whole tub to fix it with no directions anywhere on how to do it. I had a Maytag top load washer for 15 years before this. They worked perfectly when I sold them. I thought these would be a great purchase for a lot longer than 2 years.

Bought a Maytag refrigerator/freezer 18 months ago. The freezer went bad. The first repair guy said it needed a new computer board which wasnt covered. Called Maytag, they wanted another repair service to look at it. He said it needed a new evaporator. We have now spent $250 to be told the repair will cost another $500. Maytag will make a goodwill gesture because we are a nonprofit business to cover the part only so we will still be out another $300. This is unacceptable for a relatively new Maytag. Obviously they can no longer be counted on to back their equipment. Very disappointing.

So this washer, Bravos MCT cleans good not great. Saves water but clothes dont always come out clean or smell fresh. We have had it for just over a year and the control panel stopped working. Warranty is good for only 1 yr. UGHH!! It is all one unit so the complete circuit board had to be replaced. Half the cost of this washer new! I saved money by replacing it myself. Took 15 minutes. Very easy. Disappointing when you see this is a come problem with this model.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

We purchased our Maytag dishwasher on 12-26-2013. It was installed in early Jan. We did not buy an additional warranty. We put our faith in the Maytag name. We had no problems with our dishwasher. It was smooth and quiet. The one year warranty ended in Jan. 2015. In March of 2015, our dishwasher control panel began to go crazy. A short while later our Maytag shut down completely. Every now and then the washer will come on by itself. We will try and cut it off. It cuts off when it is ready. We have got quotes on getting it fixed by Maytag. With installation and tax, our Maytag Dishwasher cost us $649.22. Our complaint is the same complaint of thousands of other customers - the control panel. Maytag should have a recall and fix this problem. Maytags remedy for this problem is to sell a warranty for each year that a family owns the dishwasher. That is not acceptable. Please consider a recall on this item. Our model is MDB7749SBW2. Our serial #F33406909. Thanks for your help.

I purchased a Maytag Bravo Washer and Dryer about 2 years ago; dissatisfied with the products. Washer continues to smell. I clean it all the time with the Affresh tablets. Usually, I have to use 2 bags just to get it not to smell for at least 2 weeks. Now, the glass front dryer is rusting out around the window.

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

This machine sucks. Im down to washing three to four items only on an extra capacity machine because every single load becomes unbalanced. Feeling the weight of each item and then placing it correctly doesnt work. Repairman came out. Said it was balanced. Lie. At this point I want to take a sledgehammer to it and send the pieces one by one to Maytag. They should be embarrassed to even have this product for sale to the public with their name on it.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

Thankfully, Home Depot replaced the washer when Maytag wouldnt authorize a replacement after I had it for 3 days. Maytag wanted me to order a part, wait for the part, and then schedule their third party service contractor. It’s been about 2 weeks without a washer. Ive been posting about my experience and received an email from Maytag asking me to post feedback on their site, but it was rejected. Their note to me was “Our publication guidelines do not permit content that references a service policy, customer service interaction, or customer service question.” In other words, theyre not at all interested in customer service. Maytag/Whirlpool is no longer the brand to look for.

Failed after only 13 months with light use. I have a Whirlpool extended warranty which I had to fight to get them to honor. Then someone came to fix my washer and needed part was ordered, but part isnt available and company wont tell me when it will be. I have received 6 part availability dates so far. Whirlpool wont help. Over two months now without a washer. Ive asked them to replace machine or give me my money back, but they refused. The Whirlpool Extended Warranty group doesnt answer their phones, was put on hold for a long period.

We bought this Maytag MFI2269DRM01 Fridge/Freezer in June 2016. We have nothing but trouble. First the center rail holding up the Fruit/Veg drawers snapped within a month then the freezer drawer would not close properly which gave us all sorts of problems (door open lights flashing and fridge staying on longer. Lights not working etc.) The service tech came out and tried to fix it and went away saying it was not repaired that he would need a new freezer drawer. In the meantime I had to push the drawer to try and get it to work right. Now the handle is loose and the stainless steel front of the drawer is damaged by pushing it in so much.This repair started in November and now it is the end of March. I asked them to replace the complete unit but they say that the warranty is just to repair. It seems like they have no parts to fix this. Then the new center rail snapped again!!! When they sent the part out to me to install, I found the main frame of the Fruit/Veg rack at the back had snapped. Everything is brittle plastic with not enough support. (The only vegetable that I think I can put in the drawers is mushrooms.) I thought by buying a Maytag that the name sold it. What a piece of junk it is!!! Will never buy another Maytag product!!!

This is the worse washer... As many other have complained I have the same problems. This washer it will not fill with water ever. It doesn’t rinse clothes or clean them as I’m use to the old washers doing. From day one I noticed the water does not fill in the tub and wondered how can the clothes be getting cleaned properly. Getting a F51 code and after going on YouTube and checking for problems it seems to say the same code after it works for a bit. This is the worse appliance I have ever purchased. I am so frustrated and will never purchase a Maytag anything again. Never did in the past up to this one and never will after this one.

MER8700DH - Within 6 months, left rear burner stopped working and Maytag repaired it under warranty. Within next 6 months, and just before end of warranty, right front burner stopped working and again Maytag covered it under warranty. Within the second year of ownership, the oven was not working correctly and Maytag refused to cover it because it was off warranty. So I called a local appliance repair company who gave me an estimate of over $300 to repair it and basically advised against repair stating that this stove was a piece of junk. So I replaced it with a GE and junked the old one before it was even two years old. I filed a complaint with Maytag. At first they said they would go half on the labor, but then they said I should have bought the extended warranty and refused all further help.

I have never owned a Maytag in my life but was told it was the best on the market. That is so wrong. I purchased my Maytag Bravos washer and it has been a nightmare. Never again will I buy a Maytag. I have replaced two belts. It never spins the clothes out. Always have to restart it to respin. It turns off in the middle of the cycles. It will take hours and hours to do one load. At this time it just puts up the minutes and counts them down...does nothing. I am just fed up with this washer. I also bought a Maytag Centennial Commercial dryer. I have replaced a belt once. I would highly recommend not buying the Maytag Bravos washer. Save yourself the headache.

When purchasing a microwave for our kitchen the Maytag MMV4203DB00 had all the functions I wanted. Just after a year its quite cooking. The fan would still run but not heat anything. I called Maytag and was told basically, tough luck. I said something about Maytag, that it was supposed to be a great brand and should last longer than 1 year. The part to fix it plus labor was going to cost nearly as much as a new microwave to replace it. Now, the microwave has started to turn on by itself. Customer service was very rude and came off with a we dont really care attitude. I will never buy Maytag again.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

Dishwasher could do better with washing the dishes better and less recycling time. Also, it would be better if it had a self cleaning unit on it.

I purchased a Maytag Dishwasher Model MDB7749SBM3 in January of 2014. I have had issues with the control board for the past month: lights come up at random; it takes 3 to 10 trials to get it to start and now it is dead. After reading many reviews on this site, I now understand what the problem is. I called Maytag customer service and they wanted to schedule a service call at $98 just for the diagnostic. I asked the Maytag associate whether the control panel issue was a common problem and she said she would research that but did not give me an answer. I am totally disgusted by this company!!! I would be happy to join a class action suit.

Under a year old @MaytagBrand fridge stopped working and they couldnt get a repairman here for a week. I said this was unacceptable--we would lose hundreds of dollars in groceries and months of breast milk. They didnt care. I asked if they would reimburse me for a private repairman, they said no. Less than a year old. Friends, I implore you, never buy @MaytagBrand. This customer service is truly unacceptable.

We bought our Maytag dishwasher less than 2 years ago (model MDB8969SDM0) and we are remodeling our kitchen now January 2018, and when we pulled the dishwasher out we found that the wire (12/2) had melted into the back panel. We won’t be putting this Maytag back in.

I have a Maytag refrigerator that is 7 years old. It works fine except it needs a new freezer door gasket. In trying to get the part so it can be repaired I discovered that they had chosen to discontinue production of this part. I can no longer get it anywhere. They were the most unhelpful customer service I have ever worked with. They refused to try to find a part for another model that may work. They refused to offer a discount on a replacement product. They even refused to give me a phone number to talk to management. I had always been a loyal customer to their brand prior to this but I will never again purchase a Whirlpool or Maytag product. I dont expect not to have an issue but I do expect the ability to be supported in obtaining a commonly replaced part for a major appliance that is less than 10 years old.

Dinner ruined again... I bought all brand new Maytag stove MERS755RAW, I can only use one area and that has cant move them, the racks fall through. I have burned myself time after time when attempting to pull the racks in or out. Friends arrived and when we pulled cooked dinner out the rack fell through and it was so hot I could not hold it causing the entire dinner to come crashing down and spilling everywhere. I along with my family cannot use it again. Can anyone assist or make a recommendation? New racks do not work as it appears that oven has expanded and the dimension have changed. Do they have a recall or safety repair bulletin?

Same problems as everyone else. Water not soaking the clothes, questionable load capacity, shaky (we have engineers in the house so there is no way they did not look for floor evenness as the stores/Maytag will tell you that you may not have done, complete bs) etc. Its absolutely horrible that were all now stuck with such a terrible machine. I really wish I had read these reviews before (I googled the machine earlier but got generic stuff and didnt stumble upon these reviews until much later). Maytag should take responsibility on this as retail stores do not take back appliances unless they are defective. The Bravos is definitely a defective product from the get-go though.

Only 2 months after purchasing the Neptune Washer I required a service call as the washer was not draining. Technician replaced the pump and cleaned the drain filter. 4 months later the same issue happened. 3 months later the computer board was replaced and filter cleaned. Since purchasing this washer I have had to have 5 service calls to have it fixed. I called Maytag and they told me it is my fault the filter is clogged. Although the things in the filter are from my familys laundry the filter is located in the middle of the machine which requires the machine to be torn apart to clean the filter. This is a TERRIBLE design flaw which is NOT covered under the maintenance agreement as the service technician said this problem was caused by us. Maytag was the absolute worse to deal with as I have spoken to two levels of customer support managers and all of them said its my fault.

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

Purchased Maytag washer 2014, first the porcelain in the tub chipped then 3 years later the control unit assembly and actuator went bad they wanted $464 to fix the machine, more than we paid for it. The dealer tried to sell us insurance for this product at a hefty price, I believe all manufacturers are making their products with a short lifespan and the way for them to make money is by not making a quality product like they used to do that lasted 25 years or more, the only washer out there that is dependable is speed queen made in the USA in Wisconsin.So we the consumers are the losers in buying washers that do not live up to their name, Maytag covers themselves by a warranty of one year period for parts and labor and if you do not buy the extended warranty at a hefty price you are out of luck - so my advice is when buying a washer read all the reviews and make your decision, but the best advice is buy a speed queen online for $600 and save $400 by doing that and get a quality washer that will last 25 years or more.

We were sold a Maytag Neptune washer mah550bbw in 2004 when it was already on recall by Maytag and a class action lawsuit was filed against Maytag. We also bought an extended warranty. Now we have the same problems as the lawsuit. We own dry cleaners so we do laundry once a month for small articles. For the last few months the clothes have an odor and they come out looking not clean. We were sold a defective and recalled product and are not happy right now. We would like a fast resolution to this problem; otherwise, we seek legal actions.

Its just me and my wife. We bought a brand new, top of the line Maytag top loader washing machine 7 1/2 years ago. It quit working last week. We called a reputable appliance repair company in Toledo. It cost $88 for the technician to tell us the Maytag computer system is not worth repairing. It looks great. According to the technician Maytsg is known for selling junk. My wife and I felt we were buying a top of the line washing machine. We were duped. We had a top of the line LG top load washer delivered today. Never will we ever, under any circumstances, buy anything from Maytag.

I bought this Maytag dishwasher model # MDB7749SBM2 and of course it ran great until the warranty was up and then the touch pad started acting up where if you would press normal every other thing would light up. I replaced the keypad and then the controller and its working at this point again. The keypad ribbon cable had a big burn mark in it and by all these complaints it seems like an issue Maytag has and does not want to address. Luckily I work on electrical and was able to do this myself and I had no labor but over $300.00 in parts. What upsets me is I bought because of the reputation and the Made in America on it and it was replacing a 20 yr old Kenmore that was still working great when I took it out. With all the complaints about the same issue Maytag which is Whirlpool would step up to the plate and fix this. No more Maytags/Whirlpool for me again.

Every 3 months, the freezer compartment needs to be dismantled to unclog the defrost drain hole. When this occurs, it dumps all the defrost all over the base of the freezer which then leaks water out of the freezer door all over the floor. Clearly a design flaw and Maytag will not acknowledge this but appliance repairman says these are notorious for this. A $1700 fridge shouldnt do this. Never will I buy a Maytag again, a complete POS.

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.

I have spent a lot of effort leveling my machine, and my wife balances the load very carefully, but 10 times during a cycle, it will start slamming the tub around, so loud you can hear it from the street. I, like others in this forum, thought I was buying the best washer in the market, and paid extra for the Maytag name. It sounds like from the other complaints, that my problem is just the tip of the iceberg. It will cost me $200 to replace the suspension rods. I wouldnt mind paying the money, if I thought it would fix my problem. After reading about all of the other problems with the Bravos, I might just cut my losses, and get a new one. What a waste of $1,000.

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

White clothes come out with some sort of grease stains on them and darks come out with a detergent white scum on them. I have to put them through twice to get the scum off and I have to scrub my whites by hand. So much for your new type washers. If I could find a washer with an agitator and water saver on it, I would buy it in a flash and get rid of this so called newest thing on the market. I have to put a cleaner through it every 2-3 weeks that costs me $10.00 for 3 pucks and having to rewash my clothes does not save water or time. There is a lot to be said for the washers that had water saver on them. First of all, I could open the lid during the wash cycle and add another item. (2) I could use the last of the 2 rinse cycles from my white clothes to start a load of dark clothes, that was truly a water saver and both loads were sparkling clean. Every women that I have discussed these new machines with (both front loaders and top loaders) say that you and other companies that think you have improved wash day for women have definitely not improved it but rather made it a nightmare. Absolutely hate this product. I hasnt given me a moments satisfaction since we spent the $1,000.00.

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

I purchased the Bravos XL washer and dryer from Lowes in March of 2011. I had only had my dryer for a couple of months when it stopped drying out of nowhere. The repair man came and replaced the fuse assembly and all was well until December 2011. Again the same problem happened. I had to wait almost 10 days for someone to repair it. Once again in January 2012 for the second time the fuse assembly was replaced. Its now December 2014 and again my dryer has stopped working. Have to wait again 10 days for anyone to come and fix this. I will never buy another Maytag dryer again.