I bought my first Maytag French Door fridge about 7 years ago. When it was two it started running water on the floor. I paid a service guy to tell me a tiny little drain in the back clogged up and stopped coil defrost water from draining out. He fixed it. A year later, the fridge stopped cooling but the freezer was cold. I hired another service man who charged me a mint to diagnose that a fan that blows cold air up into the refrigerator failed. Rather than pay him again, I ordered the part. Heres the joke--the part wasnt available. An older part was substituted. Why? The first fan motor was small to make the energy start requirements--but it was too weak to be reliable. The new motor was an earlier model--almost twice as large and powerful. So much for Energy Start. At exactly 5 years and six months, the compressor went out. Im on year two with the new one. I said to myself they cant all be that bad. Now it is leaking on the floor. I have to disassemble the freezer, remove the inner wall, defrost the coils and clean out the drain hole. Wouldnt smart engineers make an easy way to do that from the back? Seems simple.

Under no circumstances should anyone buy an MMV4205DE or maybe any Maytag microwave. These units contain defective door switches and will fail within a year rendering the unit useless. The engineer that got the bright idea to protect us from starting the microwave without opening and closing the door along with the engineer that designed the defective switch scheme should be fired immediately.I purchased the unit March 2016 to replace a 10-year-old Maytag that had a failed magnetron, no problems ever with the door switches! This unit started to act up in Dec 2016 with the fatal open/close door problem, I am an EE so I opened the unit and checked the switches and found they were defective, replaced both for $80 and 6 months later the problem is back. I am buying another brand as I dont have time to deal with the problems with this unit. I now have the old white 15-year-old unit that I replaced years ago sitting on the counter to use while another unit is on order. Unit is heading for the landfill next month. Never buy a Maytag microwave, they all have the same problems!!!

Water ran out of washer and flooded my garage. 1) Replace computer. 2) Wrong computer. 3) Water still flooding garage. 4) May need water valve. 5) Showed up didnt know what to do, then left. 6) Whole new tub - 3 hour repair - 2 weeks until they have time to repair. Still waiting. HELP.

Like many others Ive read about online, our Maytag fridge model MFI2269VEW5 with bottom mount freezer has ice forming at the bottom of the freezer compartment. The ice then melts and runs onto the kitchen floor. At this point, I am able to prevent this leakage problem by removing the 1/2-inch layer of ice that builds up about once a week. Using a stiff plastic spatula, I am sometimes able to remove the ice in one large sheet but usually it breaks up and has to be removed in pieces. I have seen several videos online showing how this problem can be fixed but as a pensioner with limited income, I am sure the expense of a repairman would be prohibitive. I could likely make the suggested repairs myself but because of a knee replacement, I am not able to kneel for any length of time so that is out of the question. Besides, when we purchased this fridge 3 years ago, we expected it to run trouble free for the rest of our days. This is obviously a design problem and Maytag should be covering the cost for all repairs. However, it is a sad reality that Maytag and their owner, the Whirlpool Corporation is only interested in making a profit to satisfy their stock holders. They apparently only pay lip service to making quality products that last and customer satisfaction seems to be a thing of the past.

I bought this machine at Lowes because of the BIG drum area and about 2 years ago, it started to make funny noises; then I got the F-51 signal. I tried everything, shifting articles of clothing, then unplugging the machine and re-plugging. I am in the process of researching a plain Jane model, not one with all the bells and whistles. I am extremely dissatisfied and wish Maytag would step up to the plate and recall these machines. A motherboard and the costs for other parts, I would be better off replacing with a brand new machine. Dissatisfied!!!

Had some extra time, so I thought Id add my .02 to those including myself disgusted with Maytag products! 1st up, the Maytag washer and dryer I purchased from my nephew after his divorce. The washer shot craps 2 months after I bought it from him (out of warranty of course!). The transmission went out - cost to repair $550.00. My nephew paid $350.00 new at Sears. We happened to have our ol reliable clanking GE, so we used that while deciding what to do about the washer. In the meantime, the dryer quit heating. Cost to replace heating element - 400 smackers! Dryer new at Sears was $250.00.Come to find out that even though they had Maytag names on the washer/dryer, they were cheap copies by White/Westinghouse. Well anyway we bought a set of Whirlpool Duets before doing our homework, cuz if we knew what was gonna happen... Before we knew the trouble we were going to have with the washer/dryer, we got a Maytag Quiet Series 300 dishwasher (Maytag Quiet Series 300 MDBTT60AWW). Yip, the control panel failing problem! Only purchased 1 so far (only 1?!), but my wife likes to hand wash the dishes. If we were the typical family using the dishwasher all the time, I would have replaced more than 1 at a cost of $135.00 each from Sears and doing my own R&R work, saving on the labor. Cost new at Lowes - $350.00Up next is the Maytag fridge. I purchased it back when our 2 boys were at home. I bought it mainly for the name and large capacity. After about a year (yip out of warranty) the cooling was very uneven. Sometimes the freezer would defrost by itself, then it would start working ok again. The top couple of racks in the fridge would be quite a bit warmer than the bottom. I understood the top racks would be a little warmer, but Im talking like 15 degrees. I called a repairman and told him about the problem. He said hes received numerous complaints on this particular fridge, and theres really no way to repair it unless the electronics are replaced as well as the compressor because as the compressor gets weak over time, the electronics get fouled up by this. Cost new - $1300.00. Estimate over the phone cost to repair - $950.00 with no guarantees. Replaced with a SamsungAs far as the Duets? No problems so far. They work great and we are very pleased by them. But I have did my research and am holding my breath! I also have a Maytag microwave thats still working, but has did a couple of unusual things - the lights in the front panel display started flashing showing a fault. I unplugged it when its did this to reset it. That was a while back and now it seems ok. At least for now!When someone says, Yeah, well, you might just have a lemon, but the rest of Maytags appliances are fantastic! My wife and I when we hear this are ready for a fight! Weve had experience with all of Maytags products, and with the exception of the Duets (so far), they are nothing but junk!! Another thing I wish to mention is the Samsung fridge. Its about the only model that has a factory 5-year warranty on the compressor and major components. Weve had several fridges in our married life, and the Samsung is far superior to any fridge weve owned. Ill be looking to that brand in the future. The last item I promise: If you read the reviews on front load washers, none of them get very good ratings. If I would have know that, I may have purchased a top load. But the Duet washer does do a superior job (IMO) cleaning the clothes, and the clothes are virtually dry after the last spin.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

IT A GOOD DISHWASHER, BUT I HAVE HAD 2 PROBLEMS WITH THE CONTROLS AND HAD THE CONTROL PANEL REPLACED. TWICE. The insurance I bought with the machine, sent me a jerk to fix it, I complained and they sent a good repairman.

We got our Maytag fridge approx.18 months ago. There was no trouble the first year and there has been nothing but trouble for the last five months. The freezer started frosting one day which causes temp to get in danger zone - we defrost it with a hair dryer about every week and it has continued to frost up ever since. We have a friend that works for a certified Maytag repair business. He came to our rescue five times and called Maytag hot line for help.Together, they could only suggest that the gasket be replaced. He could not see anything wrong with it but we changed it just in case. Still, the problem continues. When we called Maytag customer service (877-556-57420), we were told that no one has had the problem before us. We just looked online; there are 521 complaints about Maytag. My question now is, how do we get a class action lawsuit going?

Received this Maytag dishwasher model MDW7749SBW1 as a gift from my son in June 2013 when my old dishwasher finally quit. January 2014, the soap/rinse aid dispenser did not work. Called Maytag and they sent repairman who replaced the part. Still did not work so repairman said another part was not communicating with the dispenser so he replaced that part. Worked fine. No charge since it was under warranty. Now its July 2014 and the touch panel doesnt work. Called for repair and was told since it is out of warranty, it will cost about $350 to repair. I called Maytag about this and said that I had a defective appliance. I was told that since I didnt buy the extended warranty, there was nothing they could do. I mentioned my last Maytag lasted 25 years and had only two minor repairs so I didnt see any reason to buy an extended warranty. I thought I was buying a good product. I was told shed register my complaint. Waiting for my repairman to come out tomorrow and see what he can do. I also have a Maytag stove. Wonder how long that will last?

I have always stored clean dishtowels and oven mitts in the storage drawer of my ovens (for over 50 years). I bought a new Maytag (2 days old) and was cooking in the oven tonight. I opened the drawer to get a mitt and it was on fire!! I am shocked. How dangerous is that! I looked over the manual and there is nothing that says towels cannot be stored in the drawer. It was literally on fire. I emptied the contents of the drawer into the sink. Has anyone else had this problem?

We have had 2 sets of Maytag washer & dryers. Our first set was a top load. When we bought the Neptune front load machines we gave the top load to our daughter and it still runs great after 14 years! Our front load W&D are 7 years old. We have a dog breeding business and when we have puppies the W&D pretty much run nonstop for 16 hours a day or longer. The blankets and towels come out like new every time!! The only complaint I have is the top of the front load machines seem to be plastic and scratched really easy. But the enamel on the top load still looks new! We plan on shopping for a new set this weekend passing these on to our daughter. We will buy ONLY Maytag for the rest of our lives!!

I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

I purchased a Maytag Bravo washing machine item # 26 23872 for $617.69 on 11-23-11 and it was delivered and set up on 12-02-11. My problem is if you have dirty sweaty clothes, you cannot get them clean with such little water. I used the HE detergent as directed. I talked to a woman at the local Sears Appliance store this morning, 7-11-12, about it. She said I need to use Affresh. So I did clean my washer but with a similar brand and my clothes are still stinky. I have even washed an empty load or two with bleach and hot water. I make sure I wash with hot water and completely dry my clothes.When you take a bath and dry yourself off with a towel, it smells like a musty basement. I am allergic to mold. I cant even take a wash cloth, get it wet and wash my face without wanting to throw up from the smell. I have had guest comment on the towels as well. Its embarrassing. The problem is you cannot clean something with an inch of water in the machine. I am 58 years old and now have to do the wash. I went to the store and asked if we could return it for an exchange or anything like a discount on a new one and she would not budge. She said it had to be within 90 days but 90 days was in the middle of winter and I was not having dirty sweaty clothes from doing outdoor yard work.Now that summer is here, 7 months later, my clothes have been smelly for a few months. I cant take it anymore. I showed the woman that I had been to Lowes and had an estimate of 10% off with free delivery, set up and haul away. She said she could do 15% but when you add on the delivery fee, it was higher than Lowes. I purchased my whole upgraded kitchen stainless steel appliances for about $7,000 and this set of washer/dryer but Sears could not help me out? What a disappointment that a loyal customer such as me could not at least get free delivery on a new washer. I went right back to Lowes and ordered the same machine I wanted Sears to sell me matching Lowes price.So now, I am stuck with a 7- to 8-month-old machine still in the one year warranty that is like new but is a worthless piece of junk as my clothes all stink. Run, dont walk if someone tries to sell you a low water HE machine. I tried sending this letter to searsinfo.com corporate office and it is rejected even though the website gives you that address.

Control Panel MDB8949SBB - I purchased my dishwasher in August of 2013. The control panel has stopped working and Maytag refuses to discuss the issue with us. Regardless of how many complaints they receive they are in denial about their product. They now offer a Repair +1 program which costs $260 for a repair and an additional 1 year warranty. If I do that I will get 1 year out of it before I run into the same problems. Any ideas?

Recently started having puddles of water on floor every morning. Just noticed a thick sheet of ice on freezer floor when I had trouble closing the freezer door. Also the water dispenses very slowly. Removed filter and it would not dispense at all. Will try melting the sheet of ice to see if that helps. Purchased 2011.

When purchasing a microwave for our kitchen the Maytag MMV4203DB00 had all the functions I wanted. Just after a year its quite cooking. The fan would still run but not heat anything. I called Maytag and was told basically, tough luck. I said something about Maytag, that it was supposed to be a great brand and should last longer than 1 year. The part to fix it plus labor was going to cost nearly as much as a new microwave to replace it. Now, the microwave has started to turn on by itself. Customer service was very rude and came off with a we dont really care attitude. I will never buy Maytag again.

I purchased a Maytag top-load washer 16 months ago. I had a problem with it four months after purchase and they told me it was not leveled, which I did not believe. I set it up as the manual said to. The washer left clothes soaking wet about every 30 loads. I continued to use it and the washer finally quit working after 16 months. The repairman found the nut which holds the pulley on the shaft that turns the drum had been loose and had been this way for some time. $129.00 later, it was fixed. It works fine now. I wonder if this problem should have been caught on the first service call when it was still under warranty.

The new Maytag commercial brand is different than the traditional Maytags. Uses less water. The new technology in the variety of choices for cycles and the steam cleaning for the dryer is a great feature.

I own a 2004 Neptune front end washer that Ive dealt with the terrible smell of stagnant water since I got it. Now the motor went and I was told I need a new washer even though the product warranty information clearly states the motor is covered for up to 10 years. The repairman told us that the motor thats in my machine is no longer being manufactured. How is that my fault? I do not have another $800.00 for a new one, which is now not even a lot of money for a washer. Ive already bought 2 washers since I built my home 14 years ago. Its just not right!

We recently purchased a Maytag Washer/Dryer set, but shortly after it arrived, we realized it was way too big for our needs, so traded it in for a smaller model (Model #MVWB765FC3). After a few washes, it developed a loud clicking noise during the entire wash cycle. Inquired about it at the retailer we purchased it from (showed them video of it) and was told it was not supposed to make that noise. Subsequently the Maytag Repairman paid us a visit and told us theres nothing wrong with the machine and that the retailer should not have told us what they did.#1). The machine did not make that noise initially. It started after a few loads of laundry. #2). The first machine we brought home was the same model (only larger) and that one didnt make that noise. To add insult to injury, the repairman has the audacity to tell my husband, Well, this visit didnt cost you anything. Really?! It cost him 4 hours of pay while he sat home waiting for you! In addition, we were delivered two cosmetically defective dryers that had to be returned. Furthermore, when I was washer/dryer shopping, I sent Maytags Customer Service Dept. an e-mail through their website asking questions about the product. To this day, I have still not received a response. I had a bad experience about 20 years ago with Maytag, but thought Id give them a second chance. I tell you...there will not be a 3rd time.

If I want to line dry something, first I have to pick off all the lint. Even when I use the dryer, I still have to pick off lint and there’s often creases with dirt dried right in. I have to inspect everything that comes out of the washer to see if it is clean before I dry it. This doesn’t save water, as I often have to wash things at least twice. Awful! Also, ridiculous. A wash machine is supposed to get things clean.

Purchased a Maytag bravo washer model #MVWX500XLO 2yrs and 6 months ago April 28/2011. In Dec. 2013, I heard a loud clanking sound and was shocked. I thought that some coins were lodged somewhere.... not the case. I put up with the clanking until after Xmas.... Finally I called a licensed technician (in business more than 20 yrs). He immediately identified the problem.... THE TRANSMISSION was shot. Wow what a shock! 65.00 dollars house call to give me the news. I phoned head office to no avail. The office said that it is not covered and that the part would be in the neighborhood of 350.00 $ and probably the installation around $160.00. I am still in shock. We paid around $750.00 for the unit. The technician said that it is one of the worst machines he has ever worked on. I am now talking with Home Depot to see if they can get some compensation on the unit (speaking with the rep). Will I buy another Maytag (by the way) made by Whirlpool... I guess not.

Never had a Maytag before I bought my house. So far the only complaint is there’s a broken piece that prevents the drawer from functioning. Otherwise, pretty good stove/range for the price. Do wish it was easier to clean without scraping anything up.

Maytag French door Bottom Mount Model # MFT2976AEW02 - Purchased this model refrigerator in late 2013. Had minor problems with ice maker for last 6 months, not have freezer problems, as the bottom freezer is not keeping food frozen. Called repairman today. He ran 64 checks on refrigerator, said to keep eye on problem and he will re check in 24 hours. Called private company, Maytag in Latrobe. They referred us to the Maytag repairman. We will keep you posted. We moved all of our frozen food to a downstairs older freezer for safekeeping. Keep checking, we will update.

I purchased my Maytag Refrigerator in Feb 2013. It is model MFF2558VEW7. It has the French doors w/ freezer at the bottom. This past week, I lost everything in the freezer. I call the Home Depot where I purchased it and they said that I have to call Maytag. I did and they sent a repairman out. It needed a compressor. After only 8 months, the compressor goes out? Why should this fridge be repaired and I not be given a new one? With all the problems with the Maytag, there needs to be one big class action filed. I asked for a loaner because it would take up to five work days for them to order the part. The answer was, We do not provide loaners.

My 2.5 year old hood range microwave stopped heating. I called repair guy, he charged $115.00 for barely a half hour and said he tightened a part and it should be fine OR the part would need to be replaced. Guess what!... That night microwave is still not heating anything. Dinos Appliance Repair is responsible to repair but Maytag doesnt stand behind its product. How do I get my money back when a repair doesnt repair anything? I wont buy Maytag again or GE.

Brand New 2019 Model 465 Washer and like others are saying is a piece of junk as they do not fill the drum with enough water even on the Deep Water fill option. The laundry does not circulate and nothing gets clean. Maytag is really poorly designed and manufactured these days and a complete Rip Off!

I purchased Maytag refrigerator (model # MSD2572VES). The fridge side stopped working. I was told that the vent/chute between the freezer and fridge ices up and prevents the cold air from the freezer to go through the fridge. The tech said that Maytag was sending him a tube of silicone to apply all around freezer and fridge and that this will probably fix the problem. So in other words, because of a design flaw, the refrigerator cannot function without adding silicone (maybe). I believe I purchased a lemon with a design flaw and they want me to accept a permanent band-aid as the solution. Shouldnt I have right to demand another model instead of having to accept a cheap alternative (silicone)? Now, if factory installed parts break off, can you imagine silicone tubed in after the fact where there was no silicone crevasse? I cant imagine it staying on - permanently.

Purchased a stackable washer and dryer (Maytag) for our new condo in Feb 2015. After it was installed a few months later the problems began. The washer wasnt removing the water from the clothes. We contacted Maytag and they informed us that they subcontract out to a company called Appliance Service of Central Florida (727-462-0394). Contacted Appliance Service and set up a date to be serviced. Since then, we have had Appliance Service out to our place over 8 times. They found fault in our control panel, our door lock, replaced our motor and have replace several other parts. It has been over 4 months since they started repairs on our machine and have informed me that they have a right to try and fix the problem. I have no problem with this but when and how long do I have to put up with this? They dont seem to care that my wife and I havent had a working washer in over 4 months.The people doing the repairs stated that this machine should have been replaced because it had or has several problems with it and after replacing the motor, electric panel etc it still isnt working. When I contacted Maytag they stated that as long as Appliance Service is working on the problem, it out of their hands. Is there anything I can do besides contacting a lawyer and spending more money?

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

At first the Maytag Bravos XL top load washing machine met all me expectations. After 3 yrs. the top where you load bleach and fabric softener began to rust. This is not covered under warranty. My last washer was a Whirlpool and had it 15 year and never had that issue. So it cant be from the water, just poor workmanship. Very disappointed. Now my lid came loose and is ready to fall off. Would not recommend.

Purchased a Maytag fridge in August of 2010. Had issues January 2014 - needed a new circuit board. At the happy cost $230.00. Well it is now May 2014 and had to have the repair man here again for another circuit board $258.64. Maytag will not stand behind their product or parts they use in their products. They flat out told us that we shouldnt have to replace the circuit board that often and then said they wont stand behind it. So buyer beware. DO NOT BUY ANYTHING MAYTAG!!!!!

Brand New 2017 Maytag Dishwasher MOB8959SFZ4 - The first time we used it it leaked from the door. I called the plumber back to make sure it was level and lined up properly and it was. Called the dealer, they sent a technician who sent away for a new latching mechanism. 3 weeks later the parts showed up. Technician installed them ran it through empty and no leaks problem solved? Nope. So I loaded it up and ran it again and it leaked. Called the dealer back but the technician is away on vacation.They suggested that the top rack might be pushing against the door for some reason when it is loaded so I removed everything from the dishwasher and ran it through again but it leaked again.Its something to do with the door not latching properly and it doesnt have a lever that locks like the old ones did. Its such a flimsy product. It baffles me that importers are getting away with bringing this crap into the country. Im now in week 5 with a brand new dishwasher that doesnt work. Maybe thats why its known for being one of the quietest dishwashers on the market.

I have a top loader Maytag washing machine, Model MVWB835DW4, bought in 11/2019. Five months of light use, the lid cracked. Received a replacement and four months later the lid once again cracked in the exact same spot. Requested replacement parts under warranty and I was told that a service tech must install the lid. Due to health and safety concerns related to Covid, we are not take any chances letting people into our home. My wife and I are 70 years old and are at high risk. Maytags response was they would not send parts under warranty to me and a service tech must install the parts. If I dont let them in by 11/2/2020 (the end of the warranty period) then I would have to pay for the parts. Maytag has the very worse customer service in the industry.

I bought the machine at Lowes. It was cheaper than the regular old agitator washers which should have been a clue. I like the old agitator washers that fill as you put in the clothes. Lowes installed it, turned it on and did not seem to care that although water should have been entering washer, none did. They rushed out. Ok, my water to the washer was bad so it was a simple plumbing fix. Less than 1 year the machine was full of water and would not agitate, spin, drain or anything. It sat full of water. My brother looked at it, fixed the hose that was no longer attached and it worked! Yeah for 1 year almost when again the belt came off, fixed again. Trying to find correct belt is starting to annoy me. I want to take it and dump it. It looks pretty but is nothing but a piece of crap. Maytag, shame on you!!!!

Wow! I wished I had reviewed this page before purchasing a Maytag. We bought a new Maytag Range (#MGR5751BDD) from Menards in March 2008. Within a couple of months, we were out of a stove. I was lighting the burner to make dinner for my family (it is a gas range) and all the burners started making a clicking noise and they caught on fire. Luckily, my husband was nearby and took the fire extinguisher to it.We thought for sure that the house was going to be gone. We contacted Maytag and they had a guy come out (wasnt the friendliest and cted like he could care less). He stated there was wiring that was bad but because we took the fire extinguisher to it we probably voided the warranty. What? He would submit a report to Maytag.Maytag reluctantly gave us some money but not near enough to cover the stove that was only a couple of months old. Now, I cant use the new range that is 2.5 years old. It pops and spurts because the regulator needs to be replaced. The bad thing is by the time we pay for a repairman and the new part, it will cost us a lot of money we cant afford. This stinks.

My refrigerator is several years old, and I would buy the same brand when I need a new one, although I would hopefully buy a counter depth one because my kitchen is so small, and the one I have now is kind of big for the space.

Purchased our side-by-side stainless steel refrigerator. After about three months, we too have a constant puddle of water outside the bottom freezer door. Maytag came out for the first year it was under warranty, each time saying it was fixed. Its still not fixed and its been three years. We have to keep a towel next to the fridge constantly and have experienced floor damage. Class action suit? Sign me up!! My Maytag double oven has stopped working, and my Maytag dishwasher does not clean my dishes at all. I will NEVER buy Maytag again.

Purchased from Lowes October 2014, paid $680.00. Now needs $600.00 in repairs for new springs and basket rim according to a Maytag appliance repairman.Washer is leaking in the front left. Repairman thinks I need 4 new springs and a redesigned taller basket rim to keep the water from pouring out over it. Yes, it is 16 months old!! Ridiculous!

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

We had 10 year old Kenmore units in the past that were much better and worked faster at both cleaning and drying. We prefer a washer with a agitator and top load. The dryer is preferred to be gas. Both the Maytag washer and dryer we have need constant repairs. Washer for control panel repairs, and dryer for false heat sensing problems. Now they say not to use dryer anti-wrinkle sheets. The washer needs less sheets put in at a time to rinse better. It is a agitator less model.

We purchased our washer Model # MHWE450WW01 and Serial # CS10502122 on March 30, 2011 along with a front loaded dryer and refrigerator on March 30, 2011 from a local store Appliance Outlet in Duncansville, PA. As with most new purchases we were excited as all three of these appliances being replaced were 20 years old. All were installed and worked great. My wife and I would often comment that in the spin cycle the washer sounded like a jet engine readying for take off. At some time in early 2014 we had Appliance Outlet come out and inspect the washer and told us that the washer was not to be that noisy and they would authorize replacement parts under warranty. In calling Maytag we were treated well and the parts came. Rear tub W10772619, Basket W10283352, Front tub W102823352.One of the parts was in fact cracked when it came in and had to be reordered. It was and several weeks later it arrived and Appliance Outlet fixed the washer. It ran so quiet we could not believe it was the same machine. In late spring of this year the noise was back. Appliance Outlet confirmed that indeed the same issue was happening and we would need to replace the parts again. In early June 2105 I called customer service and explained the situation and the rep took the notes and stated that we could indeed get these parts replaced and we as homeowners would pay for the labor. As YOU would I tried to get the labor paid for and was given the company line policy and told that there was NO way Maytag paid for the labor and the parts would be shipped. I accepted these terms.Yesterday my wife called to find out the status of the parts shipment and was taken for all intent and purpose right back thru the initial call routine. NO record of my call in early June existed and the best she got was that if Appliance Outlet would call and order the parts that they would be reimbursed. Appliance Outlet said that is NOT normal warranty procedure. Normal warranty goes from Maytag to the appliance Owner. They only confirm the issues/problems and do the labor. I am now stuck. I am also CEO of a company and while it pales in size the buck stops at my desk.

Bought Maytag Bravos in 2010. It does not clean but worse than that it rips clothing (for example: loops off pants, holes in pjs, tons of ripped towels), so many items of clothing torn that I cant keep count. Today I had a pillow case ripped apart (see image). I have had four sheets ripped that I can no longer use. Maytag should have recalled this washing machine. I have the Maytag Bravos dryer also and the drum was on backwards on it when I bought it.

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

I have used several brands of refrigerators and Maytag stood out for me. Everything works as good as new. However, my experience with ice machines, has been the first thing to quit.

The washer doesn’t have enough water to to get clothes clean. Even on deep water wash there’s is not enough water. It doesn’t get clothes clean, its very noisy. It takes a long time to was, even on short cycles. You can’t soak dirty clothes, it has a cycle for soak but it is not long enough. After about 3 months the lid licking doesn’t work and the progress lights remain on and never go off. This is the worst washer that I have ever owned. I just want to return it and get a different one!

Purchased my Maytag in November of 2010, with the freezer on bottom. Within 1 year the ice maker stopped working, and every 8 to 10 days it gets a sheet of ice on the bottom, and water runs out all over the floor. Guess, Yes the warranty expired and scared to death that Im gonna have to replace my floor. If there is a class action suit out there please inform me.

Terrible! First and last frontload washer I will ever have. Seems like every other load will not spin clothes dry no matter how many times you rebalance. You have to add more clothes or take some out dripping wet to finish the cycle. Most annoying appliance I have ever owned.

Maytag Bravos Quiet Series 300 - Just DONT BUY this junk. We bought the washer and dryer set from Home Depot in 2011 and have had nothing but trouble with the washer. Three times small objects like dimes, pennies and nickels got past the agitator into the drain pump which has been replaced twice. Beneath the agitator we even found a few missing socks. Today after a visit to the Laundromat, we bought a Samsung with a 5 year extended warranty. If that doesnt work it will be an old fashioned Speed Queen next. We will never buy anything Maytag again and I hope to influence everyone we meet about them. I cant wait to throw it into the city landfill for recycle dog food cans.

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

I have the Maytag Bravos washer and dryer. The machine has broken several times every year, and every year, Maytag makes me feel like it is my fault. They built a machine, and they do not stand behind it. And I cannot get a local machinist to work on it. I have asked Maytag to replace it from the start, and they refused, telling me its out of warranty. The only thing out of warranty is the frame--all parts are new. Here is the history:On 1/04/2008, I purchased it from Home Depot, and it cost $815. Then in 4/2009, there was an F51 code, and Maytag replaced the mother board after long hold times and much pleading to help me. They said they could do nothing, because it was out of warranty. It took manager to manager to manager to get the agreement to extend the warranty. (I then found that this was a regular Maytag issue.)From 9/2010 to 10/2010, an ld code occurred. The approved Maytag scheduled service had to come out 4 different times to attempt to fix the issue. One time, they said it was broken wires for the drain pump. The next, it was off balance; and the next, it was a sensor. Then the next time, they replaced the mother board again, and again after much argument that the part was less than a year old. Each time, they get more and more difficult to deal with and made me feel more and more like I am asking them for something unreasonable. The service guys said the washer was like new.... All new parts and I would never have a problem again. It cost $80 after argument, and Maytag covered the parts.Last 2/2011, problems include a fast spin, ld code, and off balance; and it stopped working. It needed new suspension rods which cost $250. Maytag paid nothing. Then in 8/2011, ld code started again, and I would have to turn off to drain and then restart to spin. Maytag called in a service call, and they never showed up. Every time, they said they read over my file and that theres nothing they can do to help me. And no one else for me to speak to.In 10/2011, the ld code came on permanently. The Maytag call I made this time again said there was nothing they could do to help me.I am so frustrated; I dont know what to do next. I threw away an older set working washer and dryer, thinking I made a great decision to upgrade to this new set. Now my family of 5 cannot wash our clothes. No one will work on the washers locally, and Maytag treats me like Im complaining for nothing and I should just spend endless dollars to fix this machine. And Im at a loss. I had to get a part for the dryer the other day, and the parts store person told me that this washer is one of Maytags mistakes. if that is so, why wont they help me?

25 months ago, I bought a brand new Maytag stainless steel microwave. We had upgraded all of our appliances except the microwave when we moved in our home. Our first purchase was the Maytag refrigerator. Should have learned my lesson from that because after less than a year, the freezer on the bottom went out twice! We bought this new microwave to replace an old one that didnt match the other appliances and was worn out. Two months ago, the code SE started appearing and then would go away after a few minutes. Now it doesnt go away and you cant use the microwave. I finally called a repair person since its out of warranty and was told that it would cost over $300 to fix it. Really! Im so angry because now I have to take money. I dont have to replace a microwave that should have another few years of use. Nothing at all reliable about a Maytag. I doubt Ill buy anything else they make.

I have Maytag dishwasher model # MDB7609AWB2. I purchased it from Sears on 5.30.10. It was installed 3 weeks later. From June 2010 through November 2011, the dishwasher has stopped working 3 times, every 6 months, requiring a service call to fix the electrical /circuit board problems. The aggravation of owning a poorly built machine and inconvenience of waiting for Sears to send a repair person has sealed our decision to stop doing business with Sears and Maytag.

I purchased a stainless steel (freezer bottom) Maytag refrigerator Model # MFI2670XEM0 in Oct 2012. Since then its been a nightmare. The repairman has been out four times, once being a week after I purchased it. It leaked and ruined my kitchen floor. Call Maytag, they didnt want to hear about it. As of this moment, I have three more things broken on the unit. My ice maker literally takes 3 days to make ice, the alarm on the door is broken, and the plastic crisper cracked and now will not stay in. Called Maytag again and they stated that they will not replace the item with one of equal value. They just keep repairing it. I will NEVER EVER buy another Maytag product again. I spent $1700 on this product and had faith in the Maytag product. That will never happen again. Shame on Maytag for not standing behind their products.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

This Maytag refrigerator is a counter depth so a little smaller in the Inside than I would like but fits in my tiny kitchen great. It has an inside water dispenser which is so nice because it keeps the clean look on the outside. It’s a year old and so far I have not had any problems with it.

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

I really like my Maytag dishwasher. It has been very good. I have had it for at least 10 years and it is still working fine. It is worth every penny. If this one stop working I would buy another Maytag dishwasher.

I have a Maytag dishwasher MDBH980AWQ10, within the 1st month of owning it there were issues. Now the electronic control panel is shot, dishwasher wont turn on. To replace it...almost the cost of what I paid, warranty has run out. In the last 7 years we have had problems with 5 various Maytag products, replaced our Maytag dishwasher which lasted 20 yrs and Maytag washer & dryer that lasted 30+ years and ran without a hitch. Maytag has not been helpful at all and their authorized service repair. A&E Repair Service is a bigger scam than they are. It is a waste of my finances and time to buy major appliances every 5 years. Each and every one of their new appliances has died shortly after all the warranties have run out. Im beyond frustrated, disgusted, and financially drained. It does not pay to be brand loyal to Maytag for they are no longer respectful nor appreciative of their customers. I would love to give corporate the opportunity to enjoy the same products that are in my home...in their homes...as well as the experience of their customer service. Last Maytag purchase for me! Is there anything that I can do in the meantime so Im not stuck with their lemons?

I have owned my Maytag Neptune Washer since 1998 and this is the first time that it will not drain all the water... Doing some research before I call a repairman... Have a Great day!

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

Dont buy a washer from Maytag, they put it together wrong and the transmission leaks so it will stop spinning after time and then it fries the motherboard. Too expensive to fix so you have to by a new one.. Their 10 year warranty is a joke and doesnt cover anything hasnt even been 5 years yet. Garbage products.

I purchased a french door Maytag refrigerator in Dec. 2009. We have never had decent ice. Icemaker is in the door and the seal does not keep the ice cavity cold enough. After many, many service calls and a replacement refrigerator, I was told to dump the ice twice a week and get ice out of the dispenser all day long. Really? All day long? It is model #bmft2771web1. They will not take care of this problem. It is a defect but they will not take responsibility for it. I now have a problem with my Maytag double oven! The temp on the bottom oven is 25 to 50 degrees off. I am waiting for my dishwasher and microwave to be next. I will never buy another Maytag. Buyer beware. I have to buy my ice from 7-Eleven. Thats why I bought a $ 2,100 refrigerator, so I can get my ice elsewhere!

After having had Maytag Highlander washer and dryer for 28 years in our early married life, and continuing to think that Maytag was a quality product, we purchased the Neptune front load washer MAH6700AWW. Let me tell you this IS NOT your mothers washer, nor is this Maytag a quality product. First it was necessary to install water pipe shock arrestors because of the water valve on washer causing shock in the waterline when it closed. The automatic Softener/detergent dispenser didnt work from day one.Coins and etc. constantly kept getting under flippers and couldnt be easily removed. I found that it was impossible to remove the plastic flipper without breaking a plastic mounting tab. On my first call to customer the Maytag Customer Loyalty Team, aka Customer Service (CS), I was told that the plastic flippers were not available as a separate part, and that the entire tub assembly with plastic flippers would need to be replaced. WHAT???????? THATS LUDICROUS. After temporarily securing the broken flipper to the tub, I thought Id call again about a week later to see if the previous answer was correct. On this call, the customer service lady (whose name I have), said the flippers are available and that she would send two at no charge. A few days later two flippers arrived, but were not the correct ones. I then decided to drill two holes in the tub and remounted the broken flipper with two stainless screws as a permanent solution.Two pumps needed to be replaced. One was replaced under warranty and one by myself. The one replaced by me was damaged by a coin that made its way from the tub to the pump. Other washer manufacturers provide a means of trapping such objects before they get to the pump. The wash cycle stopped unexpectedly numerous times without reason, after which the code 5d was displayed. I called Maytag Customer service. The representative didnt know what 5d code meant. Her suggestion was to call a service man. Again, I called later to ask and was told 5d meant excessive suds which wasnt the cause. Might this have been a control problem?There were three incidents of water discharging onto the floor from under the washer over the last two months, which caused water to cover an area of approximately 5 by 12 resulting in extensive cleanup in addition to damage to stored items. Since these occurrences were weeks apart and unpredictable, I knew the problem would be difficult, if not impossible, to diagnose, even by a serviceman. I concluded that it was probably a problem with the control; either filling too long or not emptying the tub before refilling for the next cycle. Thats when I decided to send this troublesome Maytag piece of junk to the landfill.

I purchased a dryer model med7500yw not even a year ago and the heating element has failed four times causing a lint fire and my clothes are burned and melted. Maytag only wants to keep servicing the dryer and not refund me my money. I asked the representative who claimed to be a supervisor would she feel safe with the dryer in her home and her rude remark was this is not about me and because the service was done back in November and now its January it will need to be serviced yet again. I am losing time from work and the repair men are rude and ignorant.

Maytag used to have a reputation for quality. Their low water energy efficient Centennial is a waste of money. Half of the time clothes come out wet and most of the time they are still dirty. Also you are only supposed fill the tub 1/4 of the way with clothes so you end up doing 3 times as many loads per week. What genius came up with this idea? Save your money. You would get better results washing your clothes in a tub with a washboard. Seriously!

Purchased my microwave in 2005 and seldom used it. However in the last few months, the halogen light which lights up the range surface has been flickering. When I asked an electrician doing other work around my house to repair it, he discovered that the halogen light is attached with a dual pin socket which is plastic. When the halogen light gets overheated (and halogen produces alight of heat) it melts the plastic. It has already melted some of the plastic socket. When it fails to operate, I will have to repair the light socket which will be very expensive or buy a new microwave. This microwave cost $800 or more because it offered convection cooking which I have seldom used.This is what is presumed quality appliance? Plus I added the cost of an extended warranty.

Bought a new Maytag Over the stove model Microwave from Lowes. It worked fine for a while. Then it started saying open close door. We opened the door and closed it, and sometimes it would work. This went on for a while till it finally would not work at all. Called for repair, the service guy came and took it apart and one of the door switches needed adjusting. He left and it was working, good deal. 2 days later open close door started all over again. We found if we lifted the door when closing it, then it would work sometimes, until one day it would no longer work. We called for another appointment, and got a new company to fix it called ABCO. The service guy showed up and tightened a screw and it worked again, said the other service guy might have forgot to tighten it down. I tried it and it worked. We did not touch it again till next morning and back to open close door again. Called ABCO back and got a new service time for Wednesday next week. Wednesday came and went, called to see why no show. They said we were not on the service list and were very sorry. So we set up a new time for them to show the following week Tuesday between 12 and 3 pm. At 3:49 they called and said sorry, but they were not going to be able to make it today. I told her then get us tomorrow and was told they were very busy and maybe Thursday would be better. I told her we were in line and and should get service before others that came on later. Her reply was maybe Monday of next week was better. After the runaround she said they would try for Wednesday tomorrow, but no promise made. After that I called Maytag direct and they said nothing they could do except make another service appointment. She told me I could get a service appointment tomorrow Wednesday between 8 and 12am or 12 and 3pm. I asked with who this time and was told ABCO who just told me they were too busy to show up tomorrow and had put me on standby. In the meantime I paid over $300 for the Maytag microwave that is never going to need service because the Maytag service man is so lonely. And bought a $ 200 Panasonic counter model so we could have a working microwave. So now we are in over $500 and still no Maytag working microwave. They did send me a letter offering me a discount on extended service plan if I want one. I told them it would be cheaper after the one year runs out under warranty, to just junk the microwave because it has cost me way more in wasted time, waiting for the lonely Maytag repairman to show up. Bottom line do not buy a Maytag Microwave model MMV4205DS-1 unless you just want a good looking decoration over your stove with a nice light, and have plenty of time waiting for the lonely Maytag repairman.

I purchased a Maytag made by Whirlpool in China about two years ago. The timer went out about nine months later. It went out again about 3 months after that and I paid to replace two sensors in addition. The washer still stops during a cycle at various times; it might be pausing or spinning or filling. When it finishes washing, sometimes it refills and leaves everything wet. I purchased from Deweys in San Clemente and they have tried to service but this is a real lemon. I will never buy anything again made by Whirlpool. I will research and find out what companies have been bought by them so as to avoid this. I note online that there are several hundred complaint problems about Whirlpool so they had to buy a company with a good reputation and ruin their product.

If you dont want your sheets ripped, then DO NOT purchase this machine. All my sheets have been torn, and many items of clothing damaged beyond repair due to this machine. Also, the machine started rusting out the first year I bought it (see photo). The repair man said that I must be doing something wrong - of course, its the consumer and not the machine - ha! Maytag should have given all of us a huge credit to a different machine because they knew of these problems early on. Never again will I purchase a Maytag appliance.

Dryer doesn’t wash all the clothes and the dryer doesn’t dry anything correctly. All, regardless of materials or size of load, comes out damp. Repairman’s excuse was that it’s a learning curve(?) and our dryer vent was the cause (which it wasn’t as we had it checked out and there was nothing in it) and that was it. Very disappointed in the washer and dryer and now the company where we bought them as it seems that we’re stuck with over $2K worth of equipment that doesn’t wash or dry well. We’re awaiting to speak with manager for a replacement of anything not Maytag. Not holding our breath and definitely not a happy customer.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

I had purchased a Maytag Front Load Washer Model no. MHWE300VW00 in 2009. Now the rear tub, basket, and belt are gone. I will never purchase another Maytag product and would not recommend them to anyone.

The steam/heat produced by the oven has made the electronic (digital) control panel buckle. Yes! This is a thousand-dollar (plus) stove, and it has warped, through no fault of mine. When I want to cook something, I press the keypad to enter the number of cooking degrees that I want. The problem is, the control board is not working correctly. Regardless of my typing in 350, it will default to 100 degrees and stay at 100.As a teacher, I do not have a huge income. I was disgusted with my recent repair estimate of $80 for a service call, and a quote of over $600 for the replacement part, plus some not-yet-determined labor installation costs. Calling the 800 phone number for Maytag connected me to some local people working as independent and overpriced contractors in Los Angeles, California. They are not MAYTAG employees, so they are not well-informed about the product.I miss the time when manufacturers stood by their products, and had factory-trained and authorized employees available to make repairs. I bought this monster Maytag stove from Lowes. I am disgusted with both companies. I have gone online to research buying my own part and hiring a local yokel to put it in. Most everyone I have encountered has been a rip-off artist. I am teaching your kids and grand kids to read and write, and you dont want to help me repair my stove without price-gouging. I can use the burners to some stove-top cooking. Life has become a hassle without being able to cook.

I purchased a Maytag dishwasher in 2010 model MDB6709AWW1. I only had it a year and the control panel went. They came out and replaced it and the guy told me that they were having a lot of the same problems. Now in 2015 it has gone again. It will run, but you cant change the settings. I took out the extended warranty on it and called 3 weeks ago and they sent out a local appliance repair company. This guy told me he had just come from another house with the same dishwasher with the same problem. He ordered the parts and I have been waiting 2 weeks. I called and the lady told me that they changed the part # and that they dont have any made yet and dont know when they will. WHAT!!! How can a company not have any parts made for their own dishwasher. I didnt buy the dishwasher when I bought all my other appliances, because there was a dishwasher here. It was gross and didnt work well. All my other appliances are Kenmore and I will stick with them. Have owned them for years and never had any problems.

We bought this range (model MER8700DS 1) March 25, 2015. Manual states when you use the oven first few times odor or smoke may happen and is normal. It also tells you this is not harmful but remove birds to another room because the fumes can kill them. Noxious fumes? Forget about the birds! Had to open up the whole house and go outside. Burned my eyes, throat and lungs. Day after day, repeatedly turned temp up to 400 trying to burn off what we thought might be a coating. No luck.Maytag got very concerned when I explained about the noxious fumes and had someone come out right away. Tech took it apart. He removed bottom (screwed in) plate that covers the bottom heating element. That plate gives the added ability to have 3 racks and make full use of the 6.3 cubic ft. capacity. Under the plate we found bits of insulation. We think that is what we smelt as it burnt up. He couldnt smell anything when he had it up to 400. So off he went thinking problem solved. Well, it still stinks. We will have Home Depot take it back. Oven takes forever to come to temp which we read in many complaints but thought thats minor. Dont know what oven to get instead since Whirlpool makes so many brand names. And other brands all seem to have their own problems.

I have a similar story to Patricia. Been without a fridge for over a month. Refrigerator is almost brand new (bought last year) and a service-person has been out three times (going on 4) to fix it. The fixes NEVER work and then they have to order ANOTHER part and I have to wait for the part AND THEN the service person. I should not have to wait once the part comes in. People who have been waiting should be at the TOP of the list. Then again, this is Maytag...probably EVERYONE has been waiting for a fix.Ill never buy a Maytag appliance again unless they give me a new appliance, pay for the apartment sized refrigerator I was forced to buy while I waited--I have 3 children who need fresh food--and replace the $300 worth of groceries that went bad when I was assured the second fix would work (they wont replace my refrigerator--if they do, Ill be satisfied--unless it breaks in less than a year, too).

After buying this dishwasher model MDB6759WWW3 in Jan. 2010, I fully expected it to work longer than it did! So far, the control panel has been replaced 5 times. The last time was Sept. 17, 2012 and already it is out again. I talked with Customer Service, since Georgia has a lemon law. After 4 times it is to be replaced.They had no record of the part that was replaced, just that a technician had come and repaired (by ordering the same part they had no knowledge of). This time they will either replace or instead of me calling, my lawyer will call. I will never buy another Maytag product and will encourage anyone else not to buy either. My daughter had the same experience with a refrigerator, a piece of junk they did nothing about. By the way, I have an extended warranty plan, which should not even be necessary!

We bought a Maytag refrigerator less than two years ago because... its Maytag. Less than a year later we had five service calls. The refrigerator wasnt cold, the freezer was the temperature of the refrigerator and it took two months and two different repair companies to fix it. And now... yes, the same problem seems to be occurring. It was a leak that was supposed fix. Cant bear the idea of going through this all over again. NEVER again Maytag!!!

We have a Maytag washer. It is the noisiest washer I have ever seen! It is in the garage as you could not have this washer in a house. The deep water wash is not deep enough. It bangs and knocks VERY loud! There have been times when all of the clothes are not even wet.

I bought my washer in 2016 and now it’s broke again. This is the fourth time! I’ve gone everything to take care of this and it’s a lemon! I will never buy Maytag again. I want to buy USA products but four times for repairs in three years is way too many. I guess it doesn’t matter what name is on it. My last washer was a GE and was still running after 15 yrs when I bought this one. Not one repair ever made on it! I’m telling everyone to stay away from maytag.

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

MY MAYTAG WASHER and DRYER ARE 17 YEARS OLD. THEY are FRONT LOADERS WHICH I THINK MAKE A DIFFERENCE. I BOUGHT MAYTAG because I had trouble with Whirlpool products that didnt go the test of time. The only problem I have with my washer is the mildew.

We purchased a Maytag refrigerator (MBF2258XEW) less than 6 weeks ago, and the compressor has already failed! Its not good, but the reason I am writing is their customer service (or lack of it)! We were told that it would take 3 weeks to get the replacement part, which was only 45 days old. Home Depot, where I had bought it, has been great; and they pushed Maytag/Whirlpool to agree to replace it. But Home Depot cannot not get us a new one until the paperwork comes from Maytag. We were told by their customer service that it would take 4 working days just to process the paperwork! Thats working days, and this is a Friday! So now, theyve all left for the weekend, and I still have no refrigerator and no idea when I will get one! They said no to getting the part faster, no to speeding up the paperwork, no to me returning it and getting a refund, and no to providing me with a rental. Please consider this when making any new appliance purchase.

Bought washer in 2010 from Sears. Told me the washer had a sensor to measure how much water it needs. Was told by service guy that was a blatant misrepresentation by the sales person. It only fills up with 8 of water. When I wash my white towels with normal dirt (dog paws), with HE detergent and bleach on various cycles, my towels come out tie-dyed with dirt. Totally dislike this machine.

Purchased a maytag washer last yr. and I feel it is the worst washer I have ever dealt with. I hate that every time I wash somethings they come out with lint all over them and they are the same things I have washed before and never had the problem, plus I hate the cover locks so you cant put water in before you put soap in.

Read MANY complaints about these units leaking water onto the floor underneath. This is accompanied by a sheet of ice forming on the bottom of the freezer under the main drawer. Good money says the cause is a plugged drain tube. I had a Subzero that suffered a similar problem. The factory installed drain tube was a flexible coil type and food particles would be easily caught, compromising water flow - leading to an ice plug and eventual evaporator ice-over. I replaced the factory tube with 1/4-inch rubber fuel line and the problem went away for good. With the Maytag units, if memory serves, access to the drain tube is from the back of the unit. You have to remove an access panel to get to it. There is typically a small removable rubber restrictor cap on the bottom of the tube; this is the most likely spot for a clog to form. Due to its design, IMO, clogging and ice-over will probably be a periodic thing. If you are really handy, you can do this maintenance thing yourself.

If you are considering this product...RUN AS FAST AS YOU CAN!! This is the biggest piece of junk Ive ever owned!! I would be more than happy to take back my 20+ year old washer over this JUNK!! It is 2-2 1/2 years old tops. I cannot count how many times my husband has already had to repair this garbage!!! I will NEVER purchase another Maytag appliance! My stainless steel dishwasher isnt any better!!

The door is worthless. I am the only washing machine user in my home and am gentle with my appliances. However over normal use, the washers door has cracked and has had to be replaced twice since it was purchased from Home Depot.

Purchased my Maytag Dishwasher MDB7749SBM on 5/13. 3 weeks ago the panel went out! I found others have had the same complaint on their Maytag Dishwashers too! I also learned this model was discontinued from Home Depot. Is this because Maytag knows this Dishwasher was JUNK and that they allowed consumers to buy this model knowing it had these problems - I believe so! I find it absolutely crazy that Maytag has not issued a RECALL and now I am out almost $700 plus if I get it fixed or buy a new one, I am out even more $$! There has to be some RESPONSIBILITY taken from Maytag!!! This Company was built on an excellent reputation but now this company reputation is considered POOR for selling defective products and doing nothing about it!

We purchased the Bravos XL washer just over a year ago. It is being replaced 1/10/2017. Simply put this is the worst product I think I have ever encountered. Extremely noisy wash cycles leave residue on the clothes, clothes do not get wet in some spots. This washer is so noisy you can hear it from outside. What an embarrassment. You have to run the clothes twice first with detergent and again without detergent to remove the residue left over from the first wash cycle (not energy efficient at all). If I could give a minus score like minus 10 I would.

We went to Lowe’s to buy a new washer when our old front loader would’ve cost more to repair than was worth it. This Bravo XL washer is the biggest rip off EVER!! I, like others, have watched with a flashlight & see that most clothes are nowhere NEAR being wet AT ALL!! Let me tell you... I am BEYOND LIVID!! I bought this washer thinking we could wash our comforter at home instead of a laundromat and WHAT A JOKE!! It would never even wet a FOURTH of a queen comforter, let alone the whole thing!! My husband had to actually LEAVE HIS JOB to go home and change because his shirts smelled like a wet animal! People actually were commenting on the smell!!Believe me, we tell EVERYONE how ridiculous this whole energy saving scam is!! AND... I am having to wash clothes TWO and THREE times to get them NEAR smelling normal!! My electric bill and water bill have gone up substantially and again, I AM LIVID BEYOND WORDS!! We spent over $900 for this washer with the extended warranty!!! NEVER EVER AGAIN WOULD I BUY MAYTAG!!! And I have tried EVERYTHING to try to rectify this; I added less detergent, I’ve used the deep water wash, extra rinses. I’ve had the Maytag technician here replacing the circuit board thinking perhaps THAT would give me more water. I sure wish we could all do something for SO MANY of us being taken advantage of!!! Did I mention I’m FUMING?!!?

I purchase all new appliances in 2010 when I built my new home. The dishwasher, stove, and over the stove microwave are Maytag. Thank goodness my refrigerator is a Kenmore. My microwave is coming up with the SE or 5E code and wont work. It would cost more to have a repairman come out and fix than to buy a new one. And from the reviews I have read it would just happen again. I cant believe with all the complaints about Maytag that any stores are still selling them. This company should be sued for selling such pieces of junk and taking our hard earned money for them. Never ever buy a Maytag anything!!!

My old washing machine was about 25 years old but still doing a fantastic job getting the laundry done. When the dryer died we decided to replace both machines so theyd match. I had been setting money aside for years in preparation for this purchase. Ive only had them for two weeks and I stay awake at night wondering what GENIUS decided you can get clothes cleaner in a tablespoon of water than you can in an adequate amount of water?! My old washer could wash a load of laundry in about 20 minutes. Again, what GENIUS decided taking over an hour to wash a load of laundry in a tablespoon of water was a better way?! What working woman would choose to double the time needed to do laundry and then not feel confident that the clothes are clean?!!! I am so mad and frustrated and disappointed and I dont know what to do. I wish I could yell at somebody!!!

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

Thankfully, Home Depot replaced the washer when Maytag wouldnt authorize a replacement after I had it for 3 days. Maytag wanted me to order a part, wait for the part, and then schedule their third party service contractor. It’s been about 2 weeks without a washer. Ive been posting about my experience and received an email from Maytag asking me to post feedback on their site, but it was rejected. Their note to me was “Our publication guidelines do not permit content that references a service policy, customer service interaction, or customer service question.” In other words, theyre not at all interested in customer service. Maytag/Whirlpool is no longer the brand to look for.