We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

Do NOT buy a Magtag washer. I purchased a brand new washer from Lowes in 2017. The washer gets stuck in the wash cycle. When I called Lowes, they said to call Maytag, who sent a service person out. The service person recalibrated the machine never ran a cycle and left. We had to call two more times after this for the same reason with the same result where the serviceman left without running a cycle. This was all while the product was under warranty. Since I had three service calls, I called Maytag frustrated that this kept happening to a new product. I was told there was nothing they could do, but if it happens again to have the service guy come back out. When the warranty runs out, I will have to pay for the service tech. Unbelievable. Save your time, money and frustration and buy a Whirlpool! I dont know how Maytag gets away with selling defective products.

I will never buy another Maytag Product in my life again. The Bravo is the worst of the worst washing machines ever. They claim to save on water but the electric it uses is terrible. You have to be a magician to untangle the clothes. Anyone who had anything to do with the workings of this machine should be fired.

I bought a Bravo washer 4 years ago from Home Depot. The spin cycle is stuck on high speed and sounds like a jet plane. Repair man came and said don’t bother to fix it because the bearing is gone. The machine cost close to $900. The repair man charged over $100. We are two retired senior citizens who dont do lots of laundry. I have read numerous complaints about the Bravo washer very similar to ours. Elder abuse should protect us from Maytag’s thievery and lack of help in repairs and replacement. A class action should be in place to address the Maytag Bravos manufacturing defects. There should be a recall and some type of reimbursement on this product . Please help us with this unjust situation.

Paint bubbling & peeling off appliance: I purchased new double convection oven from Lows (Maytag). One month after delivery, paint began to bubble and peel off. Maytag takes the position that as long as the oven functions properly, the paint is simply cosmetic and the warranty does not cover cosmetic problems. Maytags position is that even if all the paint peels off but the appliance still functions properly, too bad for you!

I bought a Maytag dishwasher less than two years ago. The Maytag repairman just informed me that the control panel, the control board and the harness were burnt and needed to be replaced with parts costing over $300. I said, No, thanks. I paid him the $99 service call fee and called Maytag to see if they would help. Nope, they pretty much said, tough luck.

Purchased a Maytag Electric Range on Jan/9/2016 and delivered Jan 12/2016. To start the Aqua Steam clean is for the birds. Does not clean worth a darn. Model MER8600DH cost $823.33 and I thought this unit was awesome until December 2018. The oven makes loud bangs and it’s not metal contracting or whatever. I stopped using my oven. Tonight my top burner started snapping like an arc or short. Yup that’s it for me. I was thinking of buying a Maytag Gas Range as I was brought up on gas and I have a plumber coming this weekend to plumb for Natural Gas but after reading all the negativity on the gas ranges as well I absolutely will not be buying a Maytag now or ever! I expected more from Maytag. :(

I purchased this relatively expensive range and could not have imagined how dissatisfied I would be. The Aqualift cleaning technology does not work. There is no way to clean the oven door. They stress not to use oven cleaner, but as the Aqualift system does nothing to clean the oven door, there is no choice but to use oven cleaner, which they say will ruin the oven coating. Also, the grates are very heavy and it is impractical to clean the range top. I wish I had researched further; this product is a MAJOR disappointment.

We upgraded and purchased a new Maytag Dishwasher Quiet Series 300 MDBH955AWQ to benefit our new kitchen remodel. Initially, the dishwasher worked great. I routinely insist on keeping the filters and interior clean as I was raised up believing that if you take care of your equipment, it will take care of you. Very shortly after purchase, there was a fire recall which was taken care of by Maytag and a third party contractor. Then as time went on, it continuously rendered out dishes with debris and food on them. Then it stopped working. It turned out the latch or door handle broke on the pivot point on the interior of the door. I got that replaced and everything was good again. Then about three months later, of course after warranty, it would not start or anything. I verified power and connections and nothing. I spent about $60 on JustAnswer for further advice and the answer was to replace the control board. After about $250 for a service call and $130 additional, it turned out the control board went out. I observed how it appeared to be a poor design due to the control board being exposed to all of the humidity and other moisture from within the dishwasher door. Then after that being fixed, about six months later, the door latch broke again. Its minor enough that you may not realize its broken until you open the door panel back up again. The plastic is breaking Im sure due to the heat and moisture, but its just minor enough that it will not make contact to indicate the door is closed. I got that replaced again for another $140. Four months of that getting fixed and Im getting the same result, no functionality at all from the control panel. In other words, the control board is out again!Ive spent almost as much in repairs that I have for the dishwasher in the first place. As many have stated before, why are we not getting quality products anymore? I went to the Maytag website to see if there were any other additional recalls for this dishwasher, and the recall site was down, so I called. The lady on the phone, as pleasant as she was, indicated that the recall for the heater coil was already performed, which I already knew. I asked, due to the other problems Ive had and money Ive spent, if there were any additional recalls, and of course the reply was no. Im used to staying with a reputable company and providing loyalty to that company for quality products and service, even if I have to spend more initially in order to spend less overall. Obviously, Maytag is now out of the question for future business or referrals. This dishwasher is getting replaced before I put one more dime into it.

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

Bought a Maytag refrigerator from Home Depot about 2 years ago. Like everyone else we are having leaking problems from the freezer drawers. I wonder if anyone has had it repaired and whether it was repaired

This is the 3rd time my Maytag refrigerator has gone out on me and its only 7 years old! Its always the same thing, my refrigerator side starts getting warmer and warmer while the freezer starts forming crystallized ice. Both times its broken down in the past it has been the defrost timer. One service man said Maytag is not the reliable company it used to be and I would be better off buying a brand from Sears (Whirlpool or Kenmore) cant remember. Anyway, each of those services was close to $300 and now Im faced with another service call. We paid $2,800 for a refrigerator we thought would last decades. Well never buy Maytag again! I wish Maytag would own up to its cheap parts and send replacements to its customers with instructions on how to install!

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

I purchased a Maytag Bravos XL at the end of June 2013 because my washer of 14 years finally quit. On the 2nd load of laundry I ran, the machine began making a terrible grinding noise. It sounds as if I am washing a load of rocks while its on the wash cycle. I immediately called the local store I purchased it from and they sent a technician out to look at the machine. He couldnt figure out why it was making this noise, so he called Maytags techs for assistance. They had him run a battery of tests and they finally determined they needed to replace the motor. Are you kidding me? On a brand new machine?! Now Im thinking I have a lemon for sure. They replaced the motor and the machine continues to make the same noise. Ive called Maytags Customer Service to let them know about the garbage theyre producing and all I got was attitude. The warranty only covers parts and does not replace machines, so Im stuck in the song and dance of lets try to figure this out and see how they can make this piece of junk work. I then asked to speak to a manager. She offered me a 6 month extended warranty for free. I guess thats a big sign that Im going to need it since what they are producing is garbage. Whatever happened to customer satisfaction? Its now just the too bad attitude. Now, I feel like Im being held hostage by my machine because I have to take time off of work for appointments with service technicians. Wheres Maytags compensation for my time and the hassle of having to deal with this? I paid $1000 for something and I guess its too much to ask for it to actually work. I am all for buying American (the machine had a sticker, proudly made in Ohio) but if this is the quality of work that they are producing they should be embarrassed to work for this company. I will never buy a Maytag again and am making it my mission to warn others of my expensive mistake!

I know that Maytag wants to conserve water by adding as little as possible... But when the damn machine puts hole in 5+ shirts Im not a happy homemaker!!! At first I thought it was the dryer so I had a repair come out and explain Im not the first person that complained of this issue. Its too late for me but Maytag needs to be aware that they are losing, what I thought to be, one of the top washers reputation.

This range and oven get unsafe, very hot on the surface and sides. Also, first time we used the oven, our oven mitts and bbq tools caught fire in the storage drawer.

No motor is available for the Bravos washer machine which is 5 years old! Now the machine is garbage and I need to buy a new one. I thought Maytag was a great brand so I purchased the Bravos but now I understand from the company that no motor replacements are available!! Wtf? Maytag/Whirlpool dont care for loyal supporters so, I am TELLING EVERYONE not to purchase Maytag/Whirlpool appliances whose name has gone for a dump with this latest situation.

I purchased model number MF12067AEW in 10/07. Motherboard has been ordered to be replaced. I have been waiting 2 weeks for the board--all over the Xmas holidays without a refrigerator! We bought this model and paid $2,800 to have a counter-depth refrigerator. I will never by anything from Maytag again. We are holding our breath to see what the cost will be and if it will it break down again. We lost all the food in the top. Ice machine flap continued to pound open and shut all the time.

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

Mine is the same sad story as all the others. Bought our Maytag dishwasher in 2013 (model MDB7749) and 15 months later, the control panel went out. We have contacted Maytag and they basically told us it could be our fault it doesnt work, so they wont fix it. Now we have learned that this is an issue that A LOT of people are having. We called their special number for this problem and were told they still wouldnt fix it since we called BEFORE having it repaired. So my question is, how is this legal and why arent they recalling this product? I know that there was a class action lawsuit against Maytag for this problem. Why dont we hold them accountable as well? This is bad business and we shouldnt allow them to take advantage of hard working people like this.

Built a new house, bought new appliances for the kitchen. Like others, did all the research, wanted to buy American made. Wow, did we ever make a mistake. Refrigerator is just over 2 years old. It is worthless. Repairman, Maytag Certified, says that it appears to be internal problems and probably come from the factory that way. He suggested I contact Maytag directly and they should be able to make things right for me and my family.So, I called, sat on hold for 10-15 minutes, and was finally connected to a customer service employee. I explained all that I knew about the problem, she pulled the repairmans notes and the notes of the technician that had spoken with the repairman. After reviewing the file, she informed me that my 2-year-old refrigerator was out of warranty and there was nothing that could be done.What ever happened to American Made companies standing behind their product? I didnt spend $2000 on a refrigerator that would last me 2 years. I expected 7-10 years, AT LEAST! I expected a company with the name MAYTAG to show some shame for creating a piece of junk and charging a customer this much money for something they know is obviously flawed from the factory. Shame? No. Guilt? None whatsoever.Caution to those considering a Maytag product. Run away! Go find a more reputable company. Go find a company who views customer service and quality products as a priority. I didnt purchase the cheapest refrigerator on purpose. I paid extra for American made and what I thought was a quality product sold by a quality company. Reality has now set in.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

The washer worked great for the first 6 months, then it didnt dissolve the soap, it wouldnt complete the cycle, and there is a loose bolt like sound when you spin the drum. The load level is not an issue. We have had the serviceman out four times, he has called the tech support each time and they cannot resolve the issue. Maytag said sorry! Unless it does it constantly then they cant help. The control panel has been replaced and the drum has been replaced. So we keep paying the water and sewer bill to rerun the load 1/2/3 times to get it to complete the cycle. This washer was purchased last May, 2011 and they say were stuck with it.

My $1,500 Maytag double oven Gemini has been trouble from the get go. 1st, trying to broil something cannot be adjusted. It sits 3 to 4 from the fire & there is no 2nd shelf. The control knobs sit on top of the stove & its easy to burn them when cooking. The broiler has always smelled like its leaking gas. Plus, the bottom oven stopped working & we had to get it repaired. The last straw was when the control board went out. We arent even going to try to repair, just going to buy a new stove. No Maytag!

Washer broke down after one year. The washer stop in the spin cycle. Called many times - got no satisfaction. Still using local laundry mat. Very disappointed. Always thought Maytag was top of the line. I guess I was wrong.

Maytag washer has increased my water bill; it was supposed to be energy efficient! Also, the washer will not wash a blanket. Sensors will move a large item to one side causing an uneven load which then causes numerous extra fills until stopped manually. I was told to add more items! A blanket barely fits in the tub. I had to invest in lint rollers since the rinse cycle is inefficient. This washing machine is useless. I should have stuck with Kenmore.

I have had my washer and dryer for more than 5 years. As normal, over time, stuff wears out and parts need to be replaced. The manual doesnt list part numbers that are needed. The website doesnt pull up part numbers when you type in the model number. After paying for overnight shipping that isnt guaranteed (and was more than the part itself), it didnt show up until a couple of days later and it was the wrong part. I would have to pay for shipping costs of the return, now tripling the cost of the actual part. Calls to customer service were not at all helpful as all they could say was that I would have to pay for the return shipping and they were sorry there was nothing they could do. I wont be purchasing anything from Maytag ever again.

My Maytag dishwasher MDB780AWW2 was recalled due to electrical problems. They gave me a voucher to purchase another one, plus I had to pay another installation fee. New unit was installed in February 2011, and here I am with a control panel issue. Seems like a similar problem, too. The lights light up, but the dishwasher wont start. Its another $345.00 plus tax repair by a repairman.

I am about to replace the control panel on my Maytag dishwasher (MDB7749SAM1) for the second time since purchasing it in 2012. Additionally, I have replaced the door gasket twice, as it becomes loose and does not properly seal, causing water to leak from the door during the wash cycle. There are many documented complaints of corrosion on the control panel ribbon cable necessitating replacement of the entire unit. If there were a way to replace the ribbon cable instead of the entire panel, it might be a bit easier to swallow the repair expense. Either way, it is ridiculous to have to spend almost 1/3 the original cost of the dishwasher to make it usable again, and twice in only 5 years time! My previous dishwasher was 30 years old and still functioning (though noisily) when I replaced it with this expensive lemon. I have not contacted Maytag, as it is not in warranty, however, it seems that a major appliance should last longer than a couple of years without issues.

We purchased the Maytag Bravos XL MCT washer and dryer in July of 2013 and have been completely and totally dissatisfied with every use since. We immediately contacted the store where we purchased them and were told we had to contact Maytag. We contacted Maytag on numerous occasions only to be read ridiculous solutions from a notebook that were no different than the instructions in the users manual and never worked. We had our first set of washer (with agitator) and dryer for 23 wonderful years. The washer absolutely does not work. The decision to remove the agitator and reduce the water levels is absurd. The soap does not get distributed, the lack of water causes loads of clothes or sheets to get rolled up into tight balls with no hope of being cleaned, and the spin cycle is so powerful it rips your clothes apart unnecessarily. The dryer is smaller than the washer and cannot handle the same size load the washer can put out and typically requires more than one cycle to complete a drying. All in all this has been the most painful experience we have ever had with any appliance. We are completely dissatisfied with both the store where we purchased these units and the complete and total lack of response from Maytag after requesting either of them to take back these units or make some equitable adjustment so we could purchase different units. We have reached a point where we will most likely store these Maytag units in the garage and purchase a new washer and dryer, being forced to accept the financial loss.

My only issue is that I am short and find it difficult to reach the wet clothes to put them in the dryer. Other than that I am quite happy with the machine. I have had no problems to date. Thank you.

Our $1,000.00 Maytag Bravos is only 4 years old (also bought the matching dryer at the same time). We have had to purchase two new motherboards for the washer and now the uL, during the spin cycle, comes on and my clothes will not spin out. I have followed the manuals directions to unplug, wait, replug, redistribute, etc... all to NO avail. So very disappointed with this machine. Bought it because it was a Maytag, but will never buy another :( I had this machine repaired with major amount of parts and expense (due to the uL problem), BUT the uL code still keeps coming up. I am one really unhappy customer.

I bought a brand new Maytag washer and dryer at Home Depot and did not use until a week later when I found out that the washer did not spin out the water and the machine turned off automatically when cycle was not finished. As a result my load was soaking wet. I called Maytag customer service and they sent the technician. I was standing next to the technician to see what was wrong with the washer. After checking several things and seeing the unresponsive of the washer the technician told me the control unit failed and the clutch also failed. He had to order the parts and it will take at least a week for him to come back and fix it.I called Maytag customer services and complained about the brand new washer and ask them to replace it with a new one as I dont know if the problems returns and it doesnt have just one failing part. Both the controlling unit and the clutch were failed. Also i bought a brand new products I expect it to work. I dont want to pay for brand new washer and I could not use it plus it took so much of my time going back and forth between Home Depot and Maytag. It was so stressful and I had tons of laundry that need to be done. I also had to take half a day off to call the Maytag customer services and Home Depot.During my first call with Maytag customer services I asked them to call my local Home Depot so Home Depot will allow me to exchange for another Maytag washer. They had refused at first but when I told them all the reasons above they agreed to call Home Depot and allow the replacement. They asked to hang on the phone while they were calling Home Depot and finally confirmed with me that I could go there and do the replacement.Surprisingly when I came to Home Depot they said they did not get any notes or call from Maytag regarding my PO# and the replacement. I had to wait for 1hr and 15 minutes for the Home Depot to be able to connect to Maytag customer services and we had to wait for their supervisor to approve the replacement. I was so disappointed later to hear Maytag supervisor telling Home Depot that I had to wait for the repair and they did not approve the replacement. Its really a waste of time and money to buy Maytag products and they dont honor what they said to customers. Once you pay them they take your money and dont really care whether their product is worth the money consumers spend on them. In general its a rip-off!!! Stay away from Maytag products if you dont want to waste your time and money!!

We bought this he Maytag washing machine about 3 years ago. I have hated it from the start and should have put a review right away because it is a piece of cr#&. It does not save any energy because I have had to rewash loads because clothes come out still dirty, lint still on them, sometimes even dry spots on clothes. I did a wash today and chunks of HE detergent still in the clothes. I am rewashing a load right now. I now have to do a presoak hoping that will help the load come out cleaner. So dont waste any money on Maytags HE machines as I will never buy another one.Being an environmentally conscious person, I thought HE was the way to go but it doesnt save any energy when you have constantly run a laundry twice to get clothes clean. It also does not do a good job spinning as clothes are still very wet. I hate this machine and I am thinking about junking it even though it still runs. Very bad purchase.

I purchased a Maytag dishwasher on Nov. 5, 2013 from Freds Appliance. I had to have the control panel fixed twice and it failed again in June 1916. My stemware had a film on it and I either had to wash it by hand or rinse it in hot water and dry by hand. Thus I felt like how could my other dishes not have this film on them even though I faithfully used Finish. I have 2 daughters who live within a half mile of me and they did not have this trouble with their dishwashers. I always felt Maytag was a top brand, but I replaced my 3 year old Maytag with a Whirlpool that my daughter and her family of 4 used for 19 years. Guess what... my glasses come out sparkling without using Finish and they wash in half the time and are dry!

My Maytag dishwasher model MDB7749SBM2 was two months out of one year warranty and the Whirlpool control panel went out. We replaced it for 80.00. 3 months later same issue. We had that replaced for free. 4 months later same issue. We had to fight but got that replaced for free. Now 2 months later same problem. It cleaned wonderful when it worked. I will never buy another Maytag or Whirlpool. I used to buy nothing but Maytag. We threw it out tonight. Tired of a dishwasher that is only part time.

Theres nothing at all good about this machine. It is impossible to work with. Ive hated it since the day I got it. Dont buy it, ever, ever, ever. You cant put additional items in once its started, you cant adjust a load thats uneven and get it to complete a cycle, it takes forever to do one wash and it often rinses multiple times and theres no way to stop it. I HATE THIS MACHINE. HATE IT. LIKE ITS A PERSON. HATE. Is that clear enough?

I purchased a Maytag Bravos in October 2015 and a month and a half later the machine began to make a tweeting sound and the clothes were coming out incredibly wrinkled no matter what spin cycle I put it on. There were also times when the clothes came out totally dripping wet like they hadnt spun at all. I called Maytag and they sent out a technician from a local store which was not a Maytag store. When I told him what was going on, his response to the machine turning out very wrinkly clothes was, Well, why dont you just chose no spin. I said to him, So the clothes wont spin and I have to take out my clothes dripping wet? Doesnt that defeat the purpose of having a washing machine that spins? He didnt say anything to me.It turned out the machine needed a new gasket motor... after two and a half months... and it would take a week - minimum - before he would come back. Maytag sent me a survey which I filled out and they called a day later. They offered me a six month extended warranty for free. I explained to them that I didnt understand why something mechanical would break after two and a half months but the woman just kept apologizing.

1 year 4 month old fridge went out. Waited a month for part/repair. No help from customer service. $1200 fridge, $700, lots of angry calls, no luck. Customer service is horrible. Will never buy Maytag again. Someone suggested to take it to small claims court. Has anyone successfully done this? Any advice how to get my $700 back? Please email me **. Thanks.

This Maytag Dryer (Model #MEDP575GWO) was delivered January 29th and the paint on top of the dryer is bubbling and peeling. I haven’t even had the unit 4 months yet and they tell me the warranty for “cosmetic” reasons is on 30 days. This is completely unacceptable and I will sue them if necessary. I am in utter disbelief.

First we bought the washer and not even a month after it was ruined. In the span of the year that weve had it, it has broken down about three times. Then we bought the matching dryer in August and by the beginning of December it has broken down. Called customer service and they are not coming until January 18. Have me waiting over a month to fix it. Worst brand ever and even worse customer service. Never again will I buy anything from this brand.

I called Sears to have a simple repair done to my Neptune washer and received a quote for $800.00++. They gave us a coupon to get a new washer at Sears and we did. Last week my dryer broke and I looked the repair up on Youtube. It looked real simple. A quote for $270 was given to us. Again a coupon if we wanted to buy new. It seems to me Sears jacks the price up on its parts and labor in order to push the customer to buy new. So far its worked for them and Im sure everyone else as well. Its not going to work out for Sears this time. Im no longer doing business with them and I will do the repair myself. I still got stuck with the service call but that will end as well going forward because I know now what the game is. Shame on you Sears. Double thumbs down for my Maytag Neptune washer and dryers.

Purchased a Maytag - MDB7749AWM1 dishwasher in 2011 from Home Depot. The door seal has failed several times and been replaced by a serviceman. The warranty has since run out but the seal continues to fall out every time you run the dishwasher and open the door. Has anyone else had a similar problem? I have considered gluing the seal in place but cant find a glue that will handle the temperature. Im sure that Maytag will say they have never seen this problem before. Maytag is off my purchase list forever!!!

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

In 2006, my wife and I purchased a new Maytag refrigerator, the model type with the freezer in a drawer near the floor and the drawer is under the main door of the fridge. The thing has a sealed system and has a freon leak which makes it nearly impossible and not financially prudent to try to fix. Two repairmen were out and I spent $200 for them to tell me the same bad news. Its unbelievable that this junk wouldnt even last ten years. What is this, Russia? Ive heard some of their awful appliance experience stories and now this can join them. The reliable Maytag repairman who never has anything to - you know the one. He is probably dead. Hes not really the one to blame here though, it is the reliability of Maytag that is dead and will remain so for as long as this company is alive. Dont ever trust or buy Maytag if you care about making your investment in new appliances last! Dont do it, people!

This oven has been used so very seldom that I didnt feel I could rate it until now. We use the oven 1-2 times a week since purchasing it in March of 2018. There hadnt been any reason to use the Self Cleaning part of the oven until last week. I have had a oven with self-cleaning for 20 years and the oven went out so we purchased this one because of its sleek look and features. However last week I decided to use the self-cleaning setting on it and came home after being gone all day to find that the house smelled like it had a fire burning in it. I ran to the oven to find the whole inside cover in a white powdery substance. It looked like a snow blizzard had gone on inside of it. I was use to a small amount of white residue being inside the oven after it finished and it just wiped right up. We spent hours vacuuming it out then scrubbing it down with vinegar water and a sponge with a scouring pad on it. The casserole spill was still on the bottom, most of the enamel is gone and the glass will not clean off. I did not use any chemicals in the oven prior to turning it to the self-clean mode, I believe that it overheated and burnt the enamel off and distorted the glass. Whirlpool offered to send me a cleaning kit. I told them that would do no good. I had already scrubbed and used a razor blade to try and clean the bottom and the glass and them sending me different cleaning supplies would not fix the fact that 80% of the inside protective coating on the oven is gone. Now it is a porous surface. A Serviceman was scheduled and he called prior to arrival today and asked me to explain what was going on with my oven. I explained and he said I can almost guarantee that Whirlpool will say that it is cosmetic and they only cover cosmetic for 3 months and that I will have to pay for a $100.00 service call. This is a load of crap. This coating is part of the oven to keep it clean and protect the metal from the high heat of baking in it. This is not cosmetic feature like the outside stainless steel finish or the black trim decor. The inside doesnt look pretty. It is a function. See the photos below. Whirlpool Range Item # 805150. Model # WEE510S0FS.

When I went to use this machine (maytag bravos). I noticed there was like a 1/4 filled in tub, checked water flow, that was fine. Then read the manual that Maytag sees using Less Water is better for clothes, I always thought it was less detergent, ohh well. Wouldnt recommend this item to anyone.

I purchased my Bravos washer in 2011. Three days before the warranty was up, the motor went out. It was leaking oil and had to be replaced. Two days later it quit working again I had to have another repairman out and found that the gear shifter had popped off so he put it back on and charged us 85.00. Luckily my husband watched him repair it and knew what to do if it happened again, which it does just about every 2 or 3 loads so I have to pull it out and pop the ring back on. I waste more water than I save with this machine. I have to drain the water so I can move the machine out and start all over because they didnt wash, and that wastes more soap. I would get laundry done cleaner and faster if I beat it against a rock. This is the worst washing machine I have ever owned and I will never buy a high efficiency washer or another Maytag again.

We purchased a Maytag Centennial line washer (Model # MVWC400XW0) and paid a little more hoping that it will last longer than a normal washer. After just 14 months, the washer breaks and we are forced to buy an extended warranty from Maytag for $300. The warranty price seemed a little high; however, the only other option was to buy a new washer. The repair guys showed and said it should be fixed.After just three weeks, the washer broke again with the exact same symptom. Since I had the extended warranty, I called in another ticket. A different repair guy showed up and he said the first guy messed up. He said the guy misread the diagnostic code and didnt even put in the part that he said he replaced. The repair guy checked with Maytag and they told him it was no longer cost effective to fix our washer. Really? They overcharged for the warranty and wont even repair it when it breaks. The only reason I can think Maytag would do this is that they know the washers are junk.

My Maytag is 2 weeks old, and knew from the start I had a lemon. The compressor sounds like a giant freezer. I had the service man take a look at it, and while he was here the compressor did not come on. He pulled the plug from the fridge and turned it back on and still it did not turn on. I asked him to stay till it turned on and he said he could not stay any longer. I waited for him from 2 PM till 7:30 PM. He was to arrive between 3 and 6. Talk about frustration, and I only wish I had read all the reports before I bought this junker. I was so worried I decided to get the insurance for 4 years. The reason the ice forms is because you have no control over the ice. You cant see them and they get stuck. I had a side by side before this, and I can kick myself for not buying a side by side again. I was told to shut it it down when youve had enough ice cubes, to stop it from getting stuck. This ice maker is so big and so hard to pull out and the switch to turn it off is on the inside. So far my only complaint was the humming, but I can see a tough road ahead.

This Maytag bravo washing machine is the worst ever machine I have owned. I bought it new, and shortly after the 1 year warranty expired, I started having problems with it. I had a repairman come out. All he did was take out the trouble shooting guide, press a code, and wait. The machine told him that each function worked. Even though it did not work properly. He hid the trouble shooting guide inside the machine, so I cannot get to it. Now I have so many problems with this machine, that it takes me all day to do 1 load. This thing makes noises that I have never heard from a washing machine in my life. I would never buy another Maytag product, nor do I recommend anyone else to buy one.

I purchased a Maytag dishwasher with a control panel in September of 2013. In August of 2014, the control panel died and did not allow me to run the washer. In March of 2015, the piece which was replaced died. When contacting Maytag, even when they did the repair the first time, said they were unable to cover the cost because it was now out of warranty. Ive seen several class action lawsuits around the product with Maytag. Do not buy a Maytag. It used to be a quality brand, but is now terrible.

My parents always bought Maytag and so did I. Ive experienced minimal problems in the past and have done my own repairs. My new MDB4949 dishwasher is GARBAGE! Imagine coming home and seeing water flowing out of the house under your back door! The water was coming from the kitchen across the kitchen floor and cascading down the stairs like a waterfall. I pressed the cancel button, nothing? Opened the door, NOTHING! Shut off the circuit breaker, NOTHING!Water continued to flow until I closed the supply valve! The dishwasher damaged my home! Six service visits later and still not fixed! 9 days out of warranty and still having the same problem! Customer service told me to hire a plumber to fix my plumbing problem with the dishwasher water supply! Thats funny because 3 other dishwashers (in the same exact place) had no problem with the water supply in the past 23 years? Two of them were Maytag!I never give less than a positive review but, this is outright FRAUD! The dishwasher has damaged my home on 2 occasions! Unless I want to stay home the whole time its running I cant use it? The customer service is pathetic at best. The control board issue is a scam by every company. Its all designed to keep you on a service plan and is a scam! Long gone are the days of the reliable rotary timer/control that lasted forever! You can thank everyone you know for not paying attention and letting this happen! I guess we can wash our own dishes by hand or comply with this obvious scam?

Maytag Bravos XL Washer and Dryer. How exciting to get a new washer/dryer!! Im a savvy bargain and quality shopper, but I really messed up here. A little over a year ago, we moved from IL back to TX and I got to buy a new washer AND dryer at the same time (a rarity). I went and looked at SO many washers/dryers and decided on the Maytag Bravos XL because a friend said she loved hers. It had a deep water wash and bedding cycle (for our blankets, comforters, sleeping bags, etc), and I thought that I could throw that wayward sock in after I started the load (unlike our previous front load washer).Where do I begin with the complaints? (And Im NOT a complainer - never filled out a review in my life). This is what I sent to Maytag: 1) Im 55 tall and can barely reach the items at the bottom of the drum, along with the lid falling on my head when Im trying to do so. 2) Forget throwing in the wayward sock - it must finish the cycle its in before it will let you unlock the lid (Where did locked lids come from anyway? Is that how those missing socks are disappearing - escaping out of unlocked lids? What are we trying to keep in or who are we trying to keep out of the machine? Doors you lock - not washing machines! I dont get it!).3) Even the deep water/bedding wash cycle does not do the job. Using the exact recommended measurement of HE liquid soap does not get the items clean. What a chore to take something out and have white detergent lines all over it and have to wipe it down with a wet cloth. Sure, I could then do a rinse and spin cycle, but since it doesnt add enough water, it doesnt come out much better. The machine senses by weight how much water to use. I am positive that every energy efficient machine is now programmed to add exactly 4 cups of water per load (regardless if its a comforter or one pair of jeans).4) Supposedly, we are saving so much water usage, but energy efficient is a misnomer - it takes me twice as long to do laundry now. The time factors are ridiculous. There are no quick cycles on this machine. If I have a load of delicate tops that just need a quick wash and rinse before I hang them out (I was not out baling hay in them, so its not like they are filthy dirty. In Texas, its the sweat that you are trying to eliminate), the least amount of time I can find on a cycle is 45 minutes. I might as well hand wash them all and be done in 5 minutes. But, that was the point of the washing machine - to do the work for me! And forget the deep water wash cycle of 58 minutes, plus the added rinse and spin cycle (to try and remove the white soap line). Its now taken one and one-half hours to try and clean/refresh a barely soiled comforter.5) The spin cycle is SO efficient, that I have items come out totally dry many times in certain spots. Im washing a comforter right now and I can guarantee you that when I remove it from the washer, there will be an entire section that looks like it never even got wet. Im no engineer, but after watching through the see-through lid, the agitation is not working well enough to get to every section.6) I havent seen a soap bubble or suds yet. You are told to use such a small amount of detergent, Im not sure how anything actually gets clean. The clothes are sprinkled with water, agitated a small amount, spun until they are almost dry and voila - the same dirty clothes come out! 7) The dryer has now ruined 2 of my bras as the hooks get caught in the mesh panel at the back. It literally melted part of the bra! I tried hooking them together before I threw them in there, but now have to put them in a lingerie bag to keep them from being mauled and mutilated. I have NEVER in 37 years of marriage and washing had that happen before.8) I literally could not get my dryer to turn on and a repairman had to come out to the house to show me the amount of pressure I had to use in one finger to start the dryer. I had almost taken a hammer to it before he arrived. Can you imagine pressing the start button on anything - the dishwasher, a hair dryer, a TV remote control, and it not turning on? And all because you pressed too hard or too light? This computer age and electronic panels are killing me! 9) The dryer has the same locking system as the washing machine. So, if you didnt see the wayward sock on the floor or between the two units until after you pushed (lightly, of course) the start button, you have to stop the unit before you can open the door to throw the sock in.I didnt mean to write a novel (about a washer and dryer, no less)! But, I feel better and hope that I have saved one woman from making the same mistake I did. Read those reviews AND believe them. And by the way, my friend who recommended the Bravos XL to me looked at mine and said Thats NOT my washer and dryer. Evidently, mine was the new and improved version! So much for that claim!

Maytag washer MVWC565FW - Clothes do not wash. They just get pushed around and the soap scum is left on the clothes even with the water at the highest level. I bought the washer override lid switch at a appliance parts store just to observe the washer cycles. The washer did not wash the clothes. I took the washer back. I like Maytag products but this washer has to be engineered.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

This is a continuing aggravation! On July 27, I discovered the dishwasher (MDB7600AWW) tub had developed a crack in the bottom right rear and had warped my countertop and the floor under it was full of water! I called the appliance store where it was purchased and was told to call Maytag. I have a 20-year warranty on the tub with free replacement of the unit if it fails. I called Maytag and was told we needed a service call to verify. I scheduled it for July 30, and 3 minutes and $75 later, yup, tub is cracked. Its a known problem, and the dealer has already replaced some for customers. I called Maytag to get the ball rolling for replacement. I spoke with Jennifer and was told shed get back to me.Meanwhile, we went to several stores, checking out other Maytag models. So, Id have some idea of what was available as a replacement. I called Jennifer on July 31 with a suggested model Id find as a suitable replacement. She said shed check and get back to me. On August 13, I called Jennifer for some answers, got the voicemail, and left a message. On August 14, I went online to chat. Finally, I was told Id have a replacement in 10-12 days. Id be contacted to schedule installation. On August 16, I called a local dealer again. He cant understand the problem. Hed replaced two others in a few days. He made some calls for us and gave us the name and phone for the company replacing the dishwasher as well as the work order. Installation was tentative for August 23. (Hed been cut out completely!)I called Optimus Solutions, and theyre awaiting shipment. Tentative installation was on August 23. On August 22, theres still no word. I called Maytag customer service. Sorry, it was shipped to the wrong address, so it was shipped back! Its now in transit and supposed to be delivered to Optimus Solutions today but not being scheduled for installation until August 31!This has become one nightmare after another with everyone pointing the finger at the next guy. Phone calls get only the same runaround. No, speaking to a supervisor wont help - theyll tell me the same thing. Isnt that convenient! Meanwhile, Im still washing dishes by hand and having psoriasis on my hands, which are like two pieces of raw meat right now. It is beyond aggravation; its bordering on torture! (No, I cant wear gloves. They make my hands sweat and even more sore!) Besides, I shouldnt be washing dishes by hand. I paid for a dishwasher that failed through no fault of my own, and now, Im being punished for purchasing it. I can guarantee that if I had no warranty and had to replace this dishwasher, it would have been replaced immediately!Never again. I purchased all Maytag products for my new home. As they fail, I can guarantee I will not be replacing them with Maytag or Whirlpool, which now owns Maytag. I will be telling everyone who will listen to stay away from Whirlpool and Maytag, because their customer service sucks big time.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

Purchased this Calypso machine as a second machine for my ranch to handle really dirty clothes. Purchased from Sears Outlet as a refurb machine would be fine for the purpose. Machine was alleged to work by Sears. Paid several hundred for the machine, brought it home, and voila it does not work. New hoses, ran all the checks, and will not fill. Called Sears and, despite the statements of the manager, was told that I have to have a 3 day old machine repaired and not replaced. This POS did not even work out of the box. Years ago I had a Calypso which is now a flower pot. Junk, Junk, Junk. NEVER buy anything from Maytag or Whirlpool.

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

I bought a brand new Maytag bottom freezer fridge in May 2005. The first thing to go was the timing switch. I lost all contents of the fridge and freezer. The next to go was the compressor. Again, all the contents of the fridge and freezer were destroyed. This was after the 5 year warranty was complete. The cosat of repairs is around $800.00, which is the cost of a new fridge. I emailed someone from customer service, who replied how happy they are to hear from me, and how I can call anytime. I called customer service, and spoke to a supervisor. The fridge was built in the USA, but cannot tell me where the parts are from. No one seems to get, that I am disgusted that an appliance would last only as long as the warranty lasts. Oh, and the repairs are only covered for 90 days. My parents have a 62 year old RCA chest freezer that is still going strong. The lesson is, dont get rid of your old appliances. They may use a lot of energy, but they last. I will never buy from Maytag, ever again.

I purchased this product at an authorized Maytag dealer sixteen months ago (Maytag front-Loading washer, model MHWE55OWW1) for approximately $1,500. The main bearing and drum are now shot. Maytag has acknowledged that it is likely defective. Notwithstanding their conclusion, Maytag has chosen not to offer a repair or replacement. The conclusion is simply that Maytag does not make a very good product, and any prospective purchasers can expect that they will not get any customer support for their products.

We bought our beautiful Maytag refrigerator model MFI2568AES at our local Home Depot approx. 4 to 5 years ago. The refrigerator stopped cooling last week and we had just renewed the warranty for 3 years. The service repair stated that the problem was not covered (internal corrosion) and they could not do anything for us. Is this how long Maytag refrigerators last? Home Depot was also not willing to do anything for us. Were very upset and disappointed and using ice chests for now.

The machine started having issues within a week of purchase. The current issue is, when running the clean cycle, the washer becomes stuck in a mode where it is constantly adding and duping water down the drain. First time it happened, I started the clean cycle before going to bed. In the morning the machine was still in the clean cycle. Running water in the tub and pumping back out down the drain. The water heater ran all night, as the washer was filling and draining the tub at the same time. Each time we attempt run the clean cycle, the washer locks up in this mode.This is the only issue I have had. Many people complain about wrinkled clothes and I agree. I take each garment out the washer and shake it out before putting it in the dryer, this makes a huge difference. Just remember, this is not your mothers washer. It does a great job at cleaning the clothes and saves many gallons of water a month.

We bought our Maytag Bravos washer and dryer 3 years ago. We bought the set from E-Z RENTALS in Crossville, TN. We paid on the set for 2 years. You can only imagine how much we paid. Two weeks after the payoff, the washing machine started acting up. We were led to believe that the set had a 10-year warranty on them. They made sure that we saw the 8-10 sticker on the front of the machine. E-Z Rentals said that we had to pay extra for the warranty. They hung us out to dry. I could have bought a nice car for what we paid for this washing machine. Now its torn up again. This will make the 3rd time that we have had to call a repairman. We are ready to take the washing machine to the dump and buy a Whirlpool. The man at E-Z Rentals said that on average, the Bravos machine lasts for 3 to 4 years. After that, its cheaper to buy a new one. Does anyone know if, in fact, these machines come with any type of warranty? We truly do not have a clue. We would be grateful for any information on the washing machine. This has been a hurtful experience. I feel that we were taken advantage of.

We bought the Bravo washer and dryer in 10/2009. Since then the dryer has never worked well. Weve had at least 8 service calls on same and the sensor doesnt work, i.e. says the clothes are dry when they arent and we always have to run them through at least two-timed cycles to make them completely dry. The washer is another nightmare. At least 8 service calls as well, and after one where the motor was replaced, it popped off and flooded my entire house. They laundry room is located on the second floor. I had to replace floors, walls, ceiling, light fixtures, etc. Insurance covered it but it never shouldve happened. Now the washer doesnt drain properly and the error code LD displays every load and we must manually drain it by either setting an extra drain cycle or take the entire machine apart and vacuum out the water. Each load takes twice the amount of time it should, if not more. But I guess its okay because the dryer takes just as long to dry a load of clothes. Something has to be done. Maytag is refusing to stand behind their products and it seems as though many of the complaints are for the same issues. Is there a lemon law for household appliances?

I purchased this washer January 2020. Bravos XL model# MVWB830DW5 is the worst washing machine ever. Does not clean your clothes, leaves soap residue on your clothes. Clothes aren’t fully submerged in water for the wash or rinse cycles. Do not waste your money. You will be highly disappointed.

Bought a new Maytag Over the stove model Microwave from Lowes. It worked fine for a while. Then it started saying open close door. We opened the door and closed it, and sometimes it would work. This went on for a while till it finally would not work at all. Called for repair, the service guy came and took it apart and one of the door switches needed adjusting. He left and it was working, good deal. 2 days later open close door started all over again. We found if we lifted the door when closing it, then it would work sometimes, until one day it would no longer work. We called for another appointment, and got a new company to fix it called ABCO. The service guy showed up and tightened a screw and it worked again, said the other service guy might have forgot to tighten it down. I tried it and it worked. We did not touch it again till next morning and back to open close door again. Called ABCO back and got a new service time for Wednesday next week. Wednesday came and went, called to see why no show. They said we were not on the service list and were very sorry. So we set up a new time for them to show the following week Tuesday between 12 and 3 pm. At 3:49 they called and said sorry, but they were not going to be able to make it today. I told her then get us tomorrow and was told they were very busy and maybe Thursday would be better. I told her we were in line and and should get service before others that came on later. Her reply was maybe Monday of next week was better. After the runaround she said they would try for Wednesday tomorrow, but no promise made. After that I called Maytag direct and they said nothing they could do except make another service appointment. She told me I could get a service appointment tomorrow Wednesday between 8 and 12am or 12 and 3pm. I asked with who this time and was told ABCO who just told me they were too busy to show up tomorrow and had put me on standby. In the meantime I paid over $300 for the Maytag microwave that is never going to need service because the Maytag service man is so lonely. And bought a $ 200 Panasonic counter model so we could have a working microwave. So now we are in over $500 and still no Maytag working microwave. They did send me a letter offering me a discount on extended service plan if I want one. I told them it would be cheaper after the one year runs out under warranty, to just junk the microwave because it has cost me way more in wasted time, waiting for the lonely Maytag repairman to show up. Bottom line do not buy a Maytag Microwave model MMV4205DS-1 unless you just want a good looking decoration over your stove with a nice light, and have plenty of time waiting for the lonely Maytag repairman.

Maytag Centennial washer - Bought this washer brand new and after the first 2 months started having issues. The washer took FOREVER to fill and to complete a basic load took literally an hour or more. Then within the next 7 months it stopped spinning out the final spin cycle. Spin light would flash as would lid lock but wouldn’t spin the water so I had to manually unplug the machine then plug in out cycle on drain and spin and that worked 50 percent of the time. Repairman came out and said could be a number of issues but he said honestly it would cost me a lot less to just go buy a new washer! This is INSANE! I grew up with the Maytag repairman commercials and thought Maytag was still top of the line but LEMME TELL YA, IT AINT! The Centennial is a total piece of crap so PLEASE don’t purchase this machine as I can promise you will NOT be satisfied! MAYTAG, STEP UP YOUR GAME BECAUSE YOU SUCK.

I purchased this refrigerator 1 1/2 yrs. ago. The refrigerator stopped getting cold about 3 months after warranty expired. I called Maytag company and told them how disappointed with their product and also how angry I was after spending $1500 only 18 months ago and now it is useless! They kept asking me if I bought the extended warranty and I said I didnt think I would have to after buying a brand new product. And then it breaks so soon!! And now they want me to spend an additional $359 to get the warranty... what a racket! She told me to look under the fridge for leaks. Sorry I cant, Im disabled. She said too bad and would have service man call me but that would be even more expensive. Woops, disconnected.

Had a problem with the control circuit board on my 6 year old refrigerator. Had it serviced and found that the problem was common, the main circuit board needed to be replaced. The service person advised me it wasnt currently available from his supplier. I call Maytag and they said it was back ordered from their parts source. When asked for an availability date, I was told the date was unknown? I started a search for the circuit board and found it was indeed a problem for many many other consumers who owned this model refrigerator. Lesson learned: Maytag is no longer a good brand to own.

I purchased a MTW6600TB0 Washer and Dryer on 6/17/07. I have had issues with the washer from the beginning; smell in towels and mechanical problems as well. The machine does not fill properly and receive error codes that are electrical issues per A & E service. I get LF errors occasionally and randomly on different cycles. I finally called for service because I now am receiving F51 Error, which has to do with the basket per A & E service technician. I was told on Black Friday that my machine required both baskets and the rotary motor. My machine is just 4/5 years old. No unusual wear and tear. There are only three people in my family and we live in a fairly warm climate so no heavy winter clothing, etc. I was told that my stainless steel basket was rusting to my plastic basket. I am still trying to comprehend the fact that two materials that are not supposed to rust are rusting. After looking for a new washer over Thanksgiving weekend, I find out that Maytag warranties their stainless steel basket and rotary motors for 10 years. So do they warranty the things they say the warranty or not? Of course, it is a holiday weekend and I cannot get a hold of Maytag. I paid for a service call and the technician told me I would be responsible for the repairs at about $500 for parts plus labor. I looked up the parts he recommended replacing and it was over $800. I paid $1000 for this machine less than 5 years ago. Thats $200 a year for the privilege to use a Maytag. Additionally, my set is black. I can not find a black washer anywhere.

We purchased a Maytag Bravo Washer and Dryer in late 2007. We had a one-year warranty on the set. At just over 2 years, we started having problems with the washer. It started making a loud noise when spinning and started beeping all the time during the cycles. We contacted Maytag and they said the only thing they could do for us was to sell us an extended/repair warranty for $320.00. If the cost of fixing the machine was too much, they had the option to replace it with another machine equal to the value of the machine in todays market, or cash, or a gift card equal to that.We were angry about the cost of the warranty and we were unemployed at the time and couldnt afford that so we just had to let it go. The machine progressively got worse where only two of the cycles would work, but not without beeping several times where you had to fix the load, and the sound got so loud it sounded like you had a jet plane just overhead. Just the other day it completely quit working. We have been in contact with Maytag several times but their only answer is their repair warranty. Weve talked to numerous appliance repairman, who all knew exactly what was wrong because they have seen it so many times, and they told us that we have several things going wrong with the machine we would probably need a new drum, a new drain pump and a new control board.We were told that it would cost more to just buy the parts than it would be to buy a new machine. In the course of our phone calls to Maytag, they have continually told us that they are sorry but there is nothing they can do, in fact they only have record of two of our calls (how convenient!). Since experiencing the issues with the machine, we have researched it online and found that scores of consumers are dealing with the exact same problems we are having which shows that there are defects in the manufacturing of these machines. Maytag should be forced to fix these problems. They are well aware of them and they should have to back up their products.There should be a class action lawsuit out against them. We were told by an appliance repairman that Whirlpool (who bought out Maytag) has a washer called Cabrio that is the exact same model as the Bravo and that they do have a class action lawsuit out against this model. Consumers that purchased the Bravo should be included in that lawsuit. I am stuck with a broken down washer, mildewing clothes and dont know where to turn outside of paying out the money for the extended warranty with no guarantee of what we would get out of it, purchasing a used set with no guarantee, or putting out the expense for a new set.This set was an expense set and we went with Maytag because they used to have a good reputation, but we feel like we have been totally cheated. If the appliance companies were forced to offer a longer warranty on their products, they would have to manufacture them at a higher standard. For the cost of these new machines this is exactly what we as consumers should expect. Please help us to know which direction to go. Even with purchasing a new machine we are apprehensive!

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

My washing machine is 2 1/2 years old. It is not overused, just 2 people in the household. Maytag wanted to sell me a contract for $320, I declined. After research I see that this machine has many complaints against it. I bought Maytag because they never need repair. I would like Maytag to fix this machine without charge or recall the machine. From what I have read, these machines are defective. The electronics are failing at 2 to 3 years.

I purchased a dishwasher model #MDB4709PAM from home Depot in March 2014. There is something wrong with the electrical and it is shocking people if you touch it. Just so were clear.. MY DISHWASHER IS ELECTROCUTING PEOPLE... Called Maytag repair because hey its only five months old. Cant send anyone out for three weeks.... three. Took an hour on the phone because I had to talk to four departments. Kept asking if anyone had been hurt seriously or property damage, so they made sure their butts were covered, sigh..... Should have bought the LG.

I bought this wash (XL HD) 1 1/2 years ago. From the time the people installed it it never worked correctly. I have never wanted to beat up an appliance before, but this washer makes me so mad that I am ready to just throw it out and buy a new one even though I paid 600.00 for it and it was more than I would ever pay for a washer. I bought this so I could wash my comforters mainly. Well I cannot wash comforters unless I wash them 5 times or at least try to wash them 5 times or more. They get unbalanced and then the machine shuts off. After doing everything from changing the hoses like somebody else suggested, it still didnt work. Along my troubles with trying to rinse and drain I did find something new that I didnt know I could do for all these months is when you put your machine on rinse, spin, dry and the extra rinse light pops on, click it and turn it off, then it reduces the spin time to 15 minutes instead of 26. Also now I have to just let my hose drain on the floor of my outside wash room because if I hook it up through the wall to drain outside it just stops with the LF code. So I have 2 inches of water on my washroom floor and it really sucks. This is the only way I can get the machine to work without turning itself off. Very disappointed with this machine that appears to be so large (looks can be deceiving). It cannot wash hardly anything and this machine should be taken off the market. It is garbage. I really wish this did work because I have spent too much time trying to rewash, respin, get all the water out of the clothes so I could dry them. This should be banned and not sold by any store.

Convenience, small, clean while you doing other jobs, it cleans while you sleeping, it's not loud, not expensive, comes in different sizes and colors, it's another helping hand, you will love it, it's worth the money.

Bought this washer and dryer 3 1/2 years ago mainly because of Maytag name and reputation. They were very expensive to purchase. The washer is a piece of junk 3 1/2 years old used for my wife and I and leaks oil all over the floor. Called repair man to come and look at it, wasnt here 5 minutes said transmission is shot. Cost over $400 to have it repaired. We are junking it and that will be the last Maytag product I ever own.

I purchased a Maytag washer from Badcock. Within 7 months the control board went out. It was down for nearly 6 months. I had to use a laundromat until I finally rented one from another place. Now again months later the control board is out again (F2F3 Call Service). Due to long wait time luckily I have another warranty but am being told I have to wait 2 weeks before a tech can come look at my washer, and that they wont have a loaner or cant just get me a new washer being the problem is THE SAME! Spent hours on hold only to be told to wait AGAIN! I would NEVER recommend dealing with this company. They used to be top of the line, but clearly not anymore.

We bought this washer in 2009. It has only been 5 years and we had a problem with the lid, now it leaks on the floor and most of all it has been rusting on the lid, the sides and rusting around the bleach port. Rusting on the top edge of the outside metal skin. I am not happy with this product at all. The serial number CV0870202. Model number is MVWB800VQZ. It is a quiet series purchased on 2009. I am not happy with the quality of this washer and I will not buy another Maytag.

Nineteen months in a home of empty nesters and the darn thing is a game of trying to outwit its electronics. We live a long way from town, which makes service calls a high dollar thing. I have spent considerable time this weekend trying to cipher its moods and order parts. This washer was purchased on an invalid reputation. Others beware.

After only three years of gentle use, my Maytag front loading washer bearing went. The repairman said this was because of too much detergent and the repair bill would be over $1100.00 (more than the cost of a new machine). I would never buy this machine again.

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

We purchased a $700 Maytag range 2 years ago and recently the oven did not work. After a Maytag authorized tech came out and checked the unit, he proclaimed the circuit board was bad and needed to be replaced. Since these ovens only have a 1-year warranty - regardless of the price you pay - he said it would be over $450 to repair it. When I asked why so expensive, he stated that they dont price the parts - Maytag does. I decided I could buy a new range for that price and get one with a warranty so I passed. I then decided to contact Maytag because I was very disappointed that such a reputable brand would prove so faulty. After writing a very polite letter and emailing customer service, they replied with a pack of lies. They stated that they have no control in what the service company charges for parts and failed to offer any assistance. They did not offer any solution except to say, Sorry. Well, you can bet that I have already spread the word to all my friends and associates about this experience and my Facebook page lit up with comments after I posted it. I will never buy another Maytag product and will make it my mission to spread the word. I had a similar issue with my brand new HP laptop but after contacting them, they immediately reached out to me and offered to pay for part of the repair!! Thats how you take care of your customers.

Bought a Maytag Washer & Dryer and after only 4 years the front panel went...cost to replace part only $653.55. After expressing concern about the price Maytag cut the cost of the part in half - now installed $475.00. Disposable dryer. Choked on it and decided to go ahead with the repair. Part was to be in in a week and it is now been a month. Maytag/Parts supplier no idea where the part is and doesnt return phone calls. Have to use the laundromat (family of 5). More money out of pocket. Not to mention time. Called Maytag again to complain about the service and having to pay more money out of pocket to use the laundromat. They basically told me, Too bad. Have used Maytag appliances over the years and always been satisfied but the company is clearly going downhill.

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

We purchased our Maytag Neptune Washer and Dryer approximately 5 years ago. Over the past year or so, Ive noticed an odor coming from our washer and it’s becoming stronger. Water is staying in the drum and there is mold growing on the rubber seal when you open the door.

I dont know where to start. This machine (Bravo XL Top Load Washer) is ridiculous! When I finally figured out how to start it, it did not rinse or spin clothes. I cannot figure out how to get it to do that so Im stuck with a washer full of wet clothes. To add insult to injury, I cannot reach into the washer to retrieve them. I am 52 and all washers are designed by freakishly tall people with NO REGARD FOR WOMEN apparently! Poorly designed! Poorly engineered! What a piece of junk!

The Maytag Bravos washing machine (Model No. MVWB75OWQ1 Type 580) is the worst Ive ever owned. The low water level obviously is not sufficient to clean the clothes as the clothes come out still dirty. I pre-treat stains carefully and follow all of the directions and 9 times out of 10, my clothes come out with the stain still there. The clothes never smell clean. In fact, they have an odor. My t-shirts still have a smell of BO under the arms and some of my clothes still smell like my perfume. They just arent clean. I feel like we put our dirty clothes in this machine and they agitate around in a little pool of water for an hour and they come out still dirty. The machine frequently gets off balance and shuts down too. If I had the money to trash this one and go buy another one - Id do it in a heartbeat. Unfortunately - Im stuck with this piece of junk until I can afford to buy a new one. This was a total waste of money and Maytag should be ashamed that they have not recalled it and given its customers a replacement option.

Ive had my washer and dryer since 2007. We purchased a new vacation home and it was included. I used the HD washing machines at my daughters, though hers was a front loader from a different company. Im unhappy with mine. Would not purchase one again. I find my clothes arent clean and my kitchen clothes and towels always have a residue on them. I now wash everything on warm, use the proper amount of soap and have to do heavy load cycle. Im still not happy, but it beats buying a new one.

We purchased all new Maytag appliances when we built our house. So far, the stove/oven has quit working and been repaired 3 times; its always the ignitor. The dishwasher has been fixed twice. The washer no longer spins out as it should. The refrigerator and dryer so far have run okay. I am definitely going to change brands with my new appliances. I will not purchase Maytag again. Its not what it used to be. I will do without oven this time, until I can buy a new one. Also, the dishwasher door has had problems from day 1, and now, it will not close at all. It seems like its off the hinge. Definitely, its not the Maytag of years ago.

Wow! I wished I had reviewed this page before purchasing a Maytag. We bought a new Maytag Range (#MGR5751BDD) from Menards in March 2008. Within a couple of months, we were out of a stove. I was lighting the burner to make dinner for my family (it is a gas range) and all the burners started making a clicking noise and they caught on fire. Luckily, my husband was nearby and took the fire extinguisher to it.We thought for sure that the house was going to be gone. We contacted Maytag and they had a guy come out (wasnt the friendliest and cted like he could care less). He stated there was wiring that was bad but because we took the fire extinguisher to it we probably voided the warranty. What? He would submit a report to Maytag.Maytag reluctantly gave us some money but not near enough to cover the stove that was only a couple of months old. Now, I cant use the new range that is 2.5 years old. It pops and spurts because the regulator needs to be replaced. The bad thing is by the time we pay for a repairman and the new part, it will cost us a lot of money we cant afford. This stinks.

In October of 2012 we bought a Maytag Refrigerator Model MFF2258VEM. In the spring and summer of 2014, we noticed puddling on our kitchen floor. We thought it was our dishwasher or sink since the $1800+ fridge was new, but couldnt find the problem. We travel a lot and are gone for extended periods. When we returned in winter of 2014, we discovered that there was substantial puddling and found a sheet of ice in the bottom of the freezer compartment. We did research and found that this is a common problem with all the bottom-freezer Maytag models, which then leak. We discovered that the leak had seeped into our kitchen sub-floor and was destroying all of our kitchen floor tile, causing cracking and breaking, a renovation of just a few years previous that cost a lot of money. There was NO problem with the floor until we put in this Maytag refrigerator. The remedy for the leaking is constant maintenance and a lot of work, totally ridiculous for a product that costs so much. I want to sue Maytag for both replacement of the refrigerator and the cost of replacement of my tile floor. Can someone please advise? Thank you.

I bought a Maytag Gemini double oven gas range 5 burners (model MGT8885XS000), even air true convection cooking. Within 4 months, 1 of the gas valves (knobs to turn gas on with) froze. I could not turn one of the top burners off. Maytag came out and fixed it. Three months later, another one froze. Again Maytag came out and fixed it. Our warranty ended. Over the next year, all five burner valves have frozen. I called Maytag, told them what happened. The most they could do for me was to give me the part half off. So I can pay $200.00 for parts and pay for a repairman to come out and fix it. The oven cost $2,000.00. I am still paying for it. Chances are if I repaired it would break again.

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

Replacing a working but noisy 14 year old Sears dishwasher for the newer Maytag was my bone head move for 2011. It died the first year control panel shot, no warranty. Paid for repair. This month dead again; same problem. Recall this stainless steel garbage. Maytag model MDBH949. Maytag, never again. Bought twice and last time.

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.