Purchased from Lowes October 2014, paid $680.00. Now needs $600.00 in repairs for new springs and basket rim according to a Maytag appliance repairman.Washer is leaking in the front left. Repairman thinks I need 4 new springs and a redesigned taller basket rim to keep the water from pouring out over it. Yes, it is 16 months old!! Ridiculous!

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

I had no issues with my washer. The best thing I ever did was stop using Sabrina softener in it and made the switch to vinegar. The worst thing I ever did was think that paying $900+ for a nice washer would get me more than a year! What a joke! I started noticing small leaks when my hardwood floors started lifting and once my husband looked into this, we realized there is no seal around the top of the drum. So there is no barrier between the drum and your floors basically. Then one day we had a flood. As we watched the cycle run, we noticed that when the water was filling into the bleach and fabric softener compartments it was coming in at such a high rate, it was spilling over the sides down to the floor. So we went to the internet and found a few complaints about this, but no answers. Thankfully we found one guy who had the exact same problem and even had pictures that matched ours. Luckily a real appliance tech answered him and he couldnt even figure it out but took a guess at what I might be: the water inlet valve. But that was just a guess. So we called around to find the part and talked with a few sales persons. One was so nice to even ask a technician standing in line. And he said that there was no way this could be it. But then we decided to take a gamble. We also noticed that both compartments were filling up at the same time, but the bleach should fill during the wash cycle and the fabric softener during the rinse cycle. So it was either the $104 water inlet valve. Or the $200+ circuit board. These are my options after already spending $900+.. So we went with the valve and thank goodness it worked!!!! It is so disappointing that after a short time, this washer broke and cause more damage to my floors. It is an awful design. I bought myself the nicest front loaders for my first house. When that broke 7 years later, I bought this washer because I liked the no agitator design without the smell of a front loader. Now when this one breaks again, Im not buying another HE machine. The majority of people I talked with today said that these HE machines are breaking down faster and faster as the get better and better. I am so beyond disappointed, angry and in shock that this washer failed in less than a year and a half time. My hope is that this review will give the answers we couldnt find without paying an arm and a leg. Is this what passes for quality these days???

I have the same complaint as everyone else. I have had my dishwasher since April 2013. Less than 9 months after having it the control panel went out and they came and replaced it. Now June 2015, 2 years and 2 months after purchasing and a year and a half after the control panel was replaced, none of the buttons work except the cancel button. How is it that these machines, as expensive as they are, crap out after 2 years! Such a waste on money!! Maytag has lost my business forever!!

This washer sucks so bad. Just got it a few hours ago and its absolutely horrible. The water just runs for the wash cycle. And I was told by the salesperson at Best Buy that it would save you water. Thats not the case. There is enough water to run over all the clothes. It doesnt agitate enough to even move the clothes around. The clothes basically sit at the bottom of the tub in the water doing nothing. This Maytag Bravo washer will be returned tomorrow. Me and my wife are highly disappointed. I wouldnt recommend this to anyone. Weve decided to just get the old washer fixed and go from there. There are too many bad reviews for this washer to still be on the market. We feel that this was a total waste of time, energy and money.

I’ve had this new stove just over a week. Used 3 times (I just moved). I have cooked on staying already on the ceramic top. I’ve had a ceramic top stove for over 20 years with barely a mark in it. Terrible. I’ve left a message with the store with no reply.

Purchased standard Maytag refrigerator w/ freezer on top in 2012. Freezer has never been able to keep ice cream. Never called for repair because after reading several of these complaints, mine seemed to be a minor frustration. However, I am waiting for the other shoe to drop.

My Maytag dishwasher is not working after 1 years & 60 months. I called Sears, where I got it. Then, Maytag company. It looks like I need to spend $167 for an electronic controller (the push buttons will not turn on) if I do myself (I doubt if I can go it, but I can try). If not, how much will I pay a tech for coming (I was told $59) plus the labor if I let him fix it. So Im looking at a total of approx $400 plus to fix a 1 1/2 yr old Maytag dishwasher. Any comments Maytag??

Purchased this oven at Lowes on 2/8/2018 for $1925. Worked good until my wife cleaned the lower oven on 11/22/2019. The next morning the oven was locked and nothing would work. We called for service and the repair bill was $194.55. I told the repairman that the oven had a 10 year warranty on it, one year on everything and the rest on the parts only. He said no, and showed me in the warranty book that it only covered two parts. Which was not the two parts he had to replace. If you purchase a oven with self-clean feature, I would recommend that you do not use it.

I have owned several dishwashers thru the years and my favorite is Maytag. Maytag is quiet, barely hear it running which is rare for a dishwasher, dependable and plenty of space for dishes, pot and pans etc. I wouldnt have any other but Maytag. Also has several options for dishwashing which is a big plus. Love Maytag!!!

I bought this washer 2 years ago, it has always been noisy and not cleaned or rinsed my clothes very well. With dark clothes, I have to rinse them twice if not three times. Now it has quit throwing out the water all together and is not rinsing the clothes at all. Paid $72 for a repair man to hook it up to his computer and tell me there was nothing wrong with it. Told me it was how I was loading it. I dont think so. Now I have to replace a two-year old machine. I will buy a basic machine that only washes my clothes this time. Nothing is made to last these days.

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

Control panel broken for a second time in 23 months: I purchased a Maytag dishwasher less than 2 years ago at Home Depot. 11 months later, the control panel went out. Specifically, the start/cancel buttons stopped working. A service tech called me under warranty; the control panel was shipped to me, and the tech fixed it. He also told me that they had had numerous problems with the control panels.13 months later, the control panel went out; specifically, the start/cancel buttons stopped working (sounds familiar). I can get nothing from Maytag, except a demand for service fees or sales pitches for extended warranties (at a price that was half of what the dishwasher cost new). They also offered me the free part as long as I pay the service call fees. I told them to just to ship me the part and that Id do it myself. Nope. I must pay the repairman. Now, theyll ship me the part if I pay for it, but they wont ship me the free part. It only comes with a service call.Maytag also told me that there were no reports of problems with the start/cancel button, an obvious lie with a quick internet search. The customer service rep sounded like she knew I was getting treated badly and kept using the word policy. Her supervisor was much more cocky and made sure I knew that I wasnt getting anything from her company.They make horrible products, attach what once was a good name, provide zero customer service, and lie to your customers. Great business practices. I will never purchase a Maytag product again.

I purchased my Maytag Bravos washing machine set in July 2007. In May 2011, I had to have the shocks and another part relating to running a balanced load replaced. I spent about $500 on those repairs. The parts to replace the shocks took more than 6 weeks to arrive! Roughly one year later, the plastic water pump has broken and needs replacing - another $100 part plus labor. I always believed Maytag was a reputable company, but I am very sad at the quality of the product I purchased based on their reputation. They should be ashamed! To date, the dryer has been good - knock on wood!

Have a Bravo Quiet Series 300, does not clean clothes because on not enough water to wash with. Have to set it on Bulk to have it clean good enough. The way it agitate and rotate the clothes turns the wash into knotted pretzels (this also makes it harder to clean the clothes) which in turn makes the spin cycle vibrate badly. Cannot put wash in and leave because of this.

Ran washer with extra rinse and clothes came out with dry spots. The only way to get clean wash is to wash everything on bulky/sheets. We lost every appliance in Sandy. If I had known the machine was so-called water saver I never would have purchased it. I was in a hurry. I hate the machine.

We bought our Maytag Neptune washer in 2005. We chose Maytag because of their reputation, their headquarters in Michigan, and because looking at the machines in the store, they seemed to be well built. Were we ever wrong! You would think paying $1000 for a machine would get you a product that lasts longer than 8 years! Our other washer (a Whirlpool) lasted 20 years and was still working. Im now consistently getting a 3e error code. In searching online, I found that this is a pretty universal problem and thought maybe Maytag had a recall on it. What a waste of valuable time. I did find out the machine was actually a Samsung. This seems like fraud. If I wanted a Samsung, thats what I would have purchased! Contacting Maytag Customer Service was like Land of the Stupid. After getting the runaround and being sent to a phone number and website that only covered Samsung I called Maytag again. I was put in contact with another person who could supposedly help me with the recall. Even though I told him what the problem was, he gave me the robot response about sending the GFCI plugin and told me, That should make your washer safe to operate. Seriously??? I replied, This wont fix the problem because THE WASHER DOESNT WORK and we got the recall part long ago. He then wanted to schedule a repair appointment. Not doing that, considering how stupid the Maytag reps I had talked to so far had been. Putting the hubby on the case, luckily hes pretty handy. On the upside, it was fun responding to the Maytag customer service survey that night, LOL. All of our other appliances are Maytag and they have all been great, but this washer is an unreliable piece of junk.

Softener container is clogging up with softener. Worse, the drain in the fridge has frozen up twice and now again I am having to pay someone to clean it out. A pool of water accumulates in front of the fridge where the ice melts. Disgusting in new appliances.

My Maytag dishwasher model MDB7749SBM2 was two months out of one year warranty and the Whirlpool control panel went out. We replaced it for 80.00. 3 months later same issue. We had that replaced for free. 4 months later same issue. We had to fight but got that replaced for free. Now 2 months later same problem. It cleaned wonderful when it worked. I will never buy another Maytag or Whirlpool. I used to buy nothing but Maytag. We threw it out tonight. Tired of a dishwasher that is only part time.

I love my gas stove. Mine is a five burner in white. Easy to clean and an accurate baking oven. Keeping the burner area clean IS a constant chore with a white surface. It would be lovely if the company made liners to catch the mess, but alas, I make my own with aluminum foil. This is an excellent stove and I’d buy it again! No buyers remorse.

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

Purchased the Maytag Bravos washer approx. 2.5 years ago. I cannot even begin to describe how disgusted I am with this washer. My clothes i.e. towels come out ripped on the edges, clothes do not get clean, shirts etc come out wrinkled no matter what setting used. It is not energy efficient because loads of laundry need to be washed twice if they are soiled (like our everyday jeans). Went back to the independent store where I purchased washer and was told to use only the bulky or gentle/delicates cycles to reduce rips in clothing. Such a complete waste of money, and it was not cheap!

We purchased a $700 Maytag range 2 years ago and recently the oven did not work. After a Maytag authorized tech came out and checked the unit, he proclaimed the circuit board was bad and needed to be replaced. Since these ovens only have a 1-year warranty - regardless of the price you pay - he said it would be over $450 to repair it. When I asked why so expensive, he stated that they dont price the parts - Maytag does. I decided I could buy a new range for that price and get one with a warranty so I passed. I then decided to contact Maytag because I was very disappointed that such a reputable brand would prove so faulty. After writing a very polite letter and emailing customer service, they replied with a pack of lies. They stated that they have no control in what the service company charges for parts and failed to offer any assistance. They did not offer any solution except to say, Sorry. Well, you can bet that I have already spread the word to all my friends and associates about this experience and my Facebook page lit up with comments after I posted it. I will never buy another Maytag product and will make it my mission to spread the word. I had a similar issue with my brand new HP laptop but after contacting them, they immediately reached out to me and offered to pay for part of the repair!! Thats how you take care of your customers.

We purchased a Maytag dishwasher in July 2013. In October 2014 it stopped working. None of the buttons on the control panel would light up. The service technician diagnosis was that it needs a new control panel at a cost of about $200.00. We chose not to do the repair since the technician recommended against it.

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

I bought my Maytag Bravos top load washer from Home Depot. In one year. I had the Maytag warranty people out three or four times. The warranty ran out and I purchased an extended warranty from A&E. I have had them out at least five times.I called Maytag and they told me since that I didn’t get the extended warranty from them, that there was nothing they could do for me. I explained to them that this washer cost me over $900 and that I have had numerous repairs on the washer, in which the warranties cost me over $400 so far.How much do I have to keep paying for this lemon? Maytag will not do anything about it! This goes to show you that paying top dollar for a washer does not guarantee you will have a good product. In this economy we can’t afford for this to happen. This is a very bad product and Maytag will not stand behind their own products, but they are willing to charge the consumer high dollar for them. This is a disgrace!

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

MDB4949SDM1 - After owning Maytag model MDB/C-2 for thirteen (13) plus years, I decided to purchase the subject Maytag Model when my 13 year old died. Big mistake. Previous model was very simplistic in rack design and it provided user-friendly options such as two detachable baskets for silverware and a special rack for delicate items.The new model has been designed so your dishes go in on angles on the top rack and as such bowls, small plates etc never stay in place once you move the rack and the lower rack configuration was redesigned and the rear area which was open to allow for bigger pots and pans to fit better has been removed, so now you have to lay your pans on top of the tines, very difficult to low the dishwasher.Additionally, I purchased the stainless steel model; apparently in the coating process a drip pattern was sealed that you can see when sunlight hits dishwasher. Further the stainless steel face that they bond to the door has popped, so when you grab the handle the face pops in and out. Lastly the new design has an adjustable upper rack; I tried numerous times to adjust the rack and couldnt so when I called Customer Service for these issues, it basically boils down to if the Service Man comes out and determines my issues are cosmetic and the rack which Ive never been able to adjust should happen to work then I have to pay the service call as there is not warranty coverage. So I declined the Service Call and advised that this would be my last Maytag purchase. I highly recommend anyone considering this unit fully investigate and test out before buying.

This was purchased 3/25/2010 with the Home Depot Service Contract thru 3/2015 . We have already had a service call in 2013. We were OK until January 2015. Now we join many other customers with the leaking defroster. We have taken all the steps of the other customers. We went and called for a service appointment. Weve spoken to Maytag Customer Service 800-253-1301. Ive asked if there was recall? NO! I asked if there was log made of my call, NO! Any work done had to with Maytag Authorized Repair Person. The Home Depot Contract use a Non-Authorized Service Person. Weve gone to Home Depot. We are in a catch 22! We have spent good money on this refrigerator. Out of sight, out of mind. We will go back to Home Depot Again!

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

This is the worse washer... As many other have complained I have the same problems. This washer it will not fill with water ever. It doesn’t rinse clothes or clean them as I’m use to the old washers doing. From day one I noticed the water does not fill in the tub and wondered how can the clothes be getting cleaned properly. Getting a F51 code and after going on YouTube and checking for problems it seems to say the same code after it works for a bit. This is the worse appliance I have ever purchased. I am so frustrated and will never purchase a Maytag anything again. Never did in the past up to this one and never will after this one.

Maytag bravo - thought it would be a good brand/buy/new technology. Absolutely nothing to like. Complete junk. Bought it in June 2013. Doesnt get things clean and takes a long time to not do that. We thought a good reputation from a major brand would mean a durable efficient washer with a reasonable capacity and good features. Unfortunately we didnt know when we bought it what a bad design/investment it was. It has destroyed numerous garments with fraying and doesnt rinse soap or dirt out because it doesnt use any water.The bravo from Maytag is supposed to be low water efficient. Unfortunately, it doesnt use enough water to wash clothes, no matter how little or how much HE soap you use. It frays clothes, leaves soap residue, wont wash jackets or blankets or bulky things, takes forever to NOT get things clean, doesnt get heavy stains or mud out, the list goes on and on.... oh, and its expensive, and breaks down a lot. I cannot believe that there has not been a government recall where the people who were unfortunate enough to buy one have been given a large amount of money back.

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

I recently bought a home that had a Maytag Neptune set. While they were newer than mine, I sold my Kenmore set, dirt cheap. Last night when I opened the washer door to take the load out, smoke billowed out. Im sick about this. There should be a recall on these washers!

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

Purchased a Maytag Dishwasher (Serial # P33706417) in Sep. 2013. In the beginning was working fine. After a year and a half started having problems pushing the button to start, not starting. Had to wait a few hours then hit it again and all the lights would light up and then it would start washing. Then when done, some lights stayed on and never went off. Then a month or 2 later, same problem but only a couple of lights would go on and when done 2 lights would blink continuously. After several months now, none of the lights are working and cant get dishwasher to start. Called a tech and he said the control board and the touchpad were not working. Would cost me over $400 plus shipping, etc. to for new. Very frustrated with Maytag, as we havent even gotten 2 years out of this dishwasher and the 1 year warranty has expired. DONT BUY A MAYTAG!!!

We had a repairman come out and take a torn pillowcase out that was jamming. It worked for a couple of weeks, now refuses to start. We have decided to rid ourselves of the Bravos 300 washing machine and not deal with Maytag any more. I would not advise anyone to buy a washer of this type, as it never really got the clothes clean to begin with.

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

Maytag dishwasher model MDB4949SDE3: This dishwasher is the biggest POS that I have ever owned in 40 years. The first one would never turn on and fill with water and after it finally did it leaked on my new floor. Waited 10 days to have it replaced. The dishwasher cycle is 2.5 - 3.5 hours and the dishes come out dirty. The top rack is not adjustable to wash odd things. I feel that these dishwashers need to be replaced.

I bought the machine at Lowes. It was cheaper than the regular old agitator washers which should have been a clue. I like the old agitator washers that fill as you put in the clothes. Lowes installed it, turned it on and did not seem to care that although water should have been entering washer, none did. They rushed out. Ok, my water to the washer was bad so it was a simple plumbing fix. Less than 1 year the machine was full of water and would not agitate, spin, drain or anything. It sat full of water. My brother looked at it, fixed the hose that was no longer attached and it worked! Yeah for 1 year almost when again the belt came off, fixed again. Trying to find correct belt is starting to annoy me. I want to take it and dump it. It looks pretty but is nothing but a piece of crap. Maytag, shame on you!!!!

The top of the range has blistered and has worn off. It cannot be cleaned. I spoke to a Maytag representative and was told to try and use magic eraser to clean around the burners. This did not work. The model number is mgr7775xs. Is there any solution to this problem. My range looks terrible.

I am, was, a loyal Maytag owner. The Bravos design, center hub, catches the clothes and rips the material. Customer service will only state damaged material is not warrantied. So I now have a washer that in addition to washing clothes rips them.

Had a Maytag washer, 3.5 tub, stopped working. The motor upper bearing lost it press, drive shaft dropped 3/4 inch and locked against lower housing, stripped out pump spline. No f/u by Maytag after many attempts. This is a design flaw, the upper housing is so thin, if it had .001 press on it I would be surprised. This flaw resulted in a cascade failure of motor and pump.

Lets be real and say that people with good experiences dont often end up on websites writing reviews because they are busy enjoying their product! I purchased my set in early 2012 and will admit that initially there was a learning curve with using a washer with no agitator. I enjoy doing laundry and Im really good at it but with this washer I had to change my routine. Always pretreat stains. Deposit clothes loosely around the drum and shake clothes loose before putting them in the dryer. My clothes come out great! I have a child, two dogs and a greasy truck driver man and everyones clothes smell great. I can wash my king bedspread and anything else in my house with no issues. And my washer has never torn any of my clothing, however fragile. I dont iron often and I hand wash nothing.I give 4 stars instead of five for the extra steps to ensure my clothes are clean and wrinkle free. No they dont make things like they used to but thats with all the new stuff. My moms 3000 dollar Samsung set (her washer) isnt working as I write this. Too bad more people with good experiences dont get online and share. Hope this has been helpful.

I purchased a Maytag dishwasher model number MDB7749SBM in May of 2013. In August the dishwasher control panel stuck on Rinse only cycle. It has been stuck on this cycle for a month. I contacted Maytag and they walked me through a reset. It has not worked. It looks to me as if the control panel has failed. This seems to be a common problem with the Maytag dishwashers. As soon as the warranty expires, so does the dishwasher. I purchased this dishwasher from Home Depot for over $600 thinking I was buying a quality product. My previous dishwasher was also a Maytag, even a lower end one that lasted almost 14 years! This one has not even lasted 14 months!!I was told by Maytag that I could purchase an extended warranty for $267.45 that would last a year. I believe, 4402 based on other reviews that I will be dumping more money into this one even after that. Very disappointed!! I will never buy another Maytag product again! I should have bought the Bosch. It was roughly the same price and high quality. I bought Maytag based on my previous experience. No More!!

I purchased a Maytag Bravos XL at the end of June 2013 because my washer of 14 years finally quit. On the 2nd load of laundry I ran, the machine began making a terrible grinding noise. It sounds as if I am washing a load of rocks while its on the wash cycle. I immediately called the local store I purchased it from and they sent a technician out to look at the machine. He couldnt figure out why it was making this noise, so he called Maytags techs for assistance. They had him run a battery of tests and they finally determined they needed to replace the motor. Are you kidding me? On a brand new machine?! Now Im thinking I have a lemon for sure. They replaced the motor and the machine continues to make the same noise. Ive called Maytags Customer Service to let them know about the garbage theyre producing and all I got was attitude. The warranty only covers parts and does not replace machines, so Im stuck in the song and dance of lets try to figure this out and see how they can make this piece of junk work. I then asked to speak to a manager. She offered me a 6 month extended warranty for free. I guess thats a big sign that Im going to need it since what they are producing is garbage. Whatever happened to customer satisfaction? Its now just the too bad attitude. Now, I feel like Im being held hostage by my machine because I have to take time off of work for appointments with service technicians. Wheres Maytags compensation for my time and the hassle of having to deal with this? I paid $1000 for something and I guess its too much to ask for it to actually work. I am all for buying American (the machine had a sticker, proudly made in Ohio) but if this is the quality of work that they are producing they should be embarrassed to work for this company. I will never buy a Maytag again and am making it my mission to warn others of my expensive mistake!

On June 5th, my husband turn off the water to the house since we were going to be away for 4 days. Unfortunately, it was not completely turned off. When we left, the washing machine was OFF, with the door slightly cracked open (to allow for circulation). When we returned, there was water all over in our upstairs, plus water had gone down the walls to the lower level. We could not figure out how the water got into the washer since it was turned off. The insurance company asked that we call a repairman to find out what was wrong. Fortunately for the repairman and us, the machine continued to go on and on after the Curtis had checked it out (it pumped out for him but not for us) and turned it OFF. It jumped from cycle to cycle after he had turned it off. Obviously the control board did its own thing. Be aware-- it can happen!!

We purchased the Maytag Bravos MCT in July 2017. Just passed the 1 year warranty and the glass door just shattered. No reason for it really other than it must have been defective. Nothing dropped on it and it wasnt cold or hot in the room. I got nothing. Maytag said they didnt know why it would happen, and would have to send service tech out. A lid for this type of washer alone is $200-$300. Buyer beware. Dont get a glass top loader.

I have used several brands of refrigerators and Maytag stood out for me. Everything works as good as new. However, my experience with ice machines, has been the first thing to quit.

Purchased a Maytag microwave/range hood in 2005. So yes, it is almost 10 years old but should the handle break off in ones hand? I would say poor material is the culprit. No use contacting the company by the looks of it... they dont stand by their product. Warranty says 10 years but broken handle would likely be cosmetic...

This Maytag Dryer (Model #MEDP575GWO) was delivered January 29th and the paint on top of the dryer is bubbling and peeling. I haven’t even had the unit 4 months yet and they tell me the warranty for “cosmetic” reasons is on 30 days. This is completely unacceptable and I will sue them if necessary. I am in utter disbelief.

I purchased a Maytag Centennial Top Load Washer in February 2012. I wish I had understood the workings of the washer before making the purchase. I am not at all happy that the lid locks as soon as the washer starts and unless I push a button to get the lid open. I cannot open the lid to maybe add more items or check to see if the water amount is sufficient or too much. I have no idea how much goes in for each water level. Of course, I cannot take water out but I could put more in if I see it is not enough. And after learning the water levels, I would know just how to determine the level I need. Some man must have designed the panel. Otherwise I am satisfied. I really like the large load capacity. I originally thought I wanted a front load to get a large capacity but this suits me fine.

The Maytag Bravos XL washing machine has a difficult time getting clothes clean. The glass top allows a person to watch the clothing being washed. After one watches this for 5 minutes, it is quite clear that the clothes are not being washed properly. Clothes frequently end up dirty at the end of the wash cycles. I personally believe the design of the agitator is so poor that it is not capable of moving the clothing around to come clean. The tub is a large 4.5 cubic foot capacity, but because it uses so little water it simply doesnt function as advertised. Often there is residue on clothing, simple stains like dirt marks dont get removed. In addition to poor cleaning, the spin cycle is simply bizarre; clothes are twisted to the point that the wrinkles created during this cycle will not come out during the dryer phase of laundry work. I am completely unsatisfied with my purchase and regret not researching this more prior to purchase. I am baffled that this product could actually make it through quality control at Maytag. I have had one service call under warranty to fix the lid not locking. This repair was completed with satisfaction.

I purchased this Maytag Washer and Dryer back in 2000 and have never been unhappy. It really gets my clothes clean and uses a lot less water than a top loader. The only issue is that if you do not clean it once in a while it will start to smell, but I have a cleaner I use every month and so far (knock on wood) it doesnt smell mildewy.

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

Bought a Maytag front load washer. When it is operating it is very loud. Some parts of the washer are made of cheap plastic. The Optimum detergent dispenser also of cheap plastic failed after 1 month. Disappointed in finding out only the outside metal box was made in America. All inside components are made in China which raised the cost $300 due to recent tariffs.

I bought a Maytag dishwasher (Model: MDBH949AWS2) from Home Depot on 07 April 11 and it died 24 August 11. I called Maytag to set up an appointment for repair. The repair person showed up and stated that the control panel needed to be replaced. Apparently, if moisture gets into the panel it shorts it out. One would think that when designing an appliance that utilizes water and creates steam, it would be sealed. Anyway, the repairman explained that because the dishwasher was in a residential program, the warranty was null and void. I wish that someone would have explained this before I purchased it. I went online to AppliancePartsPro.com and ordered the part for $100.75 including the shipping cost. Then, I went back online to look up how to install the panel. The repair person said that they are charging $133.00 for the part and $129.00 to install. A small star tip screwdriver and 15 minutes was all it took to fix. From what I have read, this will not be the last control panel but, at least, I know how to fix it. Another thing that I know is that Maytag is off my list of future appliance purchases regardless of where Im using them.

I have never been so disappointed in purchasing an appliance for my home. The Maytag Bravo XL large capacity top loader, has never worked properly, and I have many ruined pieces of clothing. Although it has a very large capacity, the water barely fills to a 1/4, and clothes are sticking out of the water, while they are supposed to be submerged/being washed IN the water. Clothes come out of the washer smelling foul. WORST WASHING MACHINE EVER.

I have used Maytag washer and dryer for over 20 yrs. I recently replaced the set we purchased in 1988 because the washer broke down but I have never had a great problem with it either. I do on a average of 3 loads of laundry a week. I measure my detergents, mostly wash on warm or cold and I keep the filters and machines clean. I would buy the same maker should I need to replace them.

The last Maytag washer was great, the dryer not so much, but I was able to repair it. This Bravos is sorry. 4 years old and the tube goes bad is not what you would expect from Maytag. Consequences, no more Maytag or GE for that matter, that dont leave many brands to choose from.

Our Maytag ref. is not quite 4 years old and it is leaking water on to our floor. The ref. is a French door with water and ice in the door and freezer on the bottom. We have to clean up puddles of water at least 3 or 4 times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasn’t Consumer Affairs demanded a recall on these expensive defective refrigerators to date?

I purchased the Maytag Bravos washer and dryer in September 2010, before moving to Washington. After a few months, the washer broke and had to have a repairman out twice to fix. It never would wash a blanket without stopping with error messages. He told these were notorious for problems. Now our dryer is leaking and not drying. I checked the vent hose and water and some wet lent are inside. In moving the dryer, I can hear a piece rattling around inside. From research and other posts, it sounds like its a broken pulley system inside. Maytag is junk. Customer service is terrible! I bought this unit during a veterans day sale at Lowes, using my veteran discount. Obviously, Maytag has no problem ripping off veterans or anyone else based on their horrible customer service. I will be actively posting as many negative online posts and videos about my experience on every forum and veteran site I can. They are horrible! Stay away from Maytag!

Purchased my Maytag Dishwasher MDB7749SBM on 5/13. 3 weeks ago the panel went out! I found others have had the same complaint on their Maytag Dishwashers too! I also learned this model was discontinued from Home Depot. Is this because Maytag knows this Dishwasher was JUNK and that they allowed consumers to buy this model knowing it had these problems - I believe so! I find it absolutely crazy that Maytag has not issued a RECALL and now I am out almost $700 plus if I get it fixed or buy a new one, I am out even more $$! There has to be some RESPONSIBILITY taken from Maytag!!! This Company was built on an excellent reputation but now this company reputation is considered POOR for selling defective products and doing nothing about it!

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

According to Maytags manual Odors and smoke are normal when the oven is used the first few times... Exposure to the fumes may result in death of certain birds. What about humans? I had serious respiratory problems and the industrial-level fumes lingered after dozens of uses. Neither the upper nor the lower ovens are calibrated. Upper oven baked at 325 when digital readout said 350. Lower oven had to be set to 365 to cook at 350. (After several puzzling baking disasters I bought an oven thermometer.) YOU are supposed to calibrate it yourself with cryptic instructions and a lot of trial and error.

I have always stored clean dishtowels and oven mitts in the storage drawer of my ovens (for over 50 years). I bought a new Maytag (2 days old) and was cooking in the oven tonight. I opened the drawer to get a mitt and it was on fire!! I am shocked. How dangerous is that! I looked over the manual and there is nothing that says towels cannot be stored in the drawer. It was literally on fire. I emptied the contents of the drawer into the sink. Has anyone else had this problem?

I will never buy another Maytag product. Our dishwasher is not even 2 years old and the control board went bad. No extended warranty was purchased because we assumed that it would last longer than 2 years when our Sears Kenmore lasted 25 years. No help from customer service. We now have to spend over $300 to get this piece of junk repaired.

I bought a high capacity Maytag Bravos washing machine, thinking it would be better than the ones that shred your clothes around the center post. Wrong. You still have to wrap your clothes around the edges as if there were a post, and even then the machine will become unbalanced (after much thumping and crashing), causing it to stop, which forces you to redistribute the weight, sometimes several times in one load of wash! I called the company and got nowhere -- I wont say nowhere fast because it took forever to get nowhere. I do not recommend this machine.

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

I read the reviews before I bought this washer, went to a major department store to buy it. This way I knew that I could get good support if something happened to it. Its been 3 months, I use the washer everyday. There are 4 adults in my building, they use it daily. I have never had a problem yet, the clothes come out cleaner than the front loader I have. It seems Maytag still makes a good product. I am the first to admit, when you make large number of products you will have some with a defect. But this washer the Centennial by Maytag works great.. Plenty of water in the tub, the clothes come out clean.. Maybe those people having problems need to stop buy at big box home centers. Theyre known for lumber not washers.

Bravos XL Washer and Dryer (Maytag) is the worst appliance set ever. Not enough water in the bin, residue despite using the correct detergent, and clothes which do not even get fully wet during the wash cycle. I am so sorry I purchased this pair - I do like the heavy duty spin, and the dryer does dry (but the door clasp has somehow come loose and stopped working - has to be wiggled into place every time I close the door). The really frustrating part is the low water levels (and even bulky is less than a half a bin of water. I am attaching a photo with two sets of sheets, a towel and three wash cloths). Most cycles only put about two inches of water in the bin - appalling. And the long long long cycles - what is energy-saving about having to do a load twice and using more than an hour for one cycle? I wish I could adjust the water levels. Seriously disappointed in this duo. Sorry I wasted my hard-earned money on it. I was seduced by a pretty exterior.

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

We purchased the Bravos X set (Model Number: MEDX700XW0 and Model Number: MVWX700XW2) form Lowes in October 2012. When the items arrived and we used the dryer for the first time in the delicate setting, the machine kept cutting off! So, Lowes brought us a new one. At first it worked but then the delicate cycle on that machine ended up not working as well a few months later. I ignored it and used the other settings. Yesterday, the washer broke. The entire basket detached! We were washing a small blanket and sheet set and kept hearing a loud banging sound. I went to check and the clothes were soaked and the entire drum was detached. I am so friggin angry! We spent over 1200 for this set and less than 3 years later, the set is ruined. I am on the phone with Maytag now b/c they need to replace this set or give us an upgraded set. They know that this set had issues yet they decided to still market and sell it. I want to sue!

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

Shame on Maytag! Customer Service is appalling! Paid 2500 for one of their top of the line refrigerator/freezer and had the repair people 5 times in one year. It was determined that it is a bad model number that Maytag wont recall but knows it is faulty. Started with ice build up in freezer making it sound like a plane taking off. It kept running trying to defrost (energy efficient-right). The repairman put in a request to have the product replaced based on symptoms and freezer being at 26 degrees. We had to wait five business days for Maytag to review it. I have a family and was having guests. They told me to buy a dorm refrigerator and they would send me a small credit towards it in 4 to 6 weeks. They finally agreed to replace the known faulty model, but I have to wait for the exchange team to contact me (2 weeks later). I keep calling and leaving messages but cant get the exchange team to even return my calls. I have my sons graduation this weekend and I dont have a freezer and my refrigerator is faulty with all my vegetables rotting within two days. It also took two days to originally get someone in management to call me back (even though it did no good - she cant help me). You cannot talk to management if you call customer service. They downright refuse! What a company!

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

Our Maytag refrigerator that is two years old has been nothing but issues just after the warranty expired. Ice maker is broken and it started having the temp alarm go off every few weeks and now every few days. It was a 1800 dollar purchase and no one has been helpful where we bought it nor has Maytag. We will never purchase another Maytag product...

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

All my kitchen appliances are from Maytag, however I would highly recommend buying the extended warranty for any appliance you buy. Maytag is not helpful to customers when it comes to repairs. They will recommend you their authorized companies which here in Colorado Springs are the one with the worse review and already knowing the the repair will cost more than the cost of a new one. You will have to be available 5 hours of your day and spend $110 for a guy to come to your house and tell you that the repair will cost more than a new one. Oh and if your microwave is a 2.0 CU like mine you will have to pay $300 plus in double labor because your microwave will require two people to take it down from the kitchen cabinet.

After seeing all the bad reviews about Maytag I decided to write my review, we purchased a Maytag washer and dryer 1990 when moving into our new home, and we still have the same set. Now it does not have a motherboard which I feel today is the major problem with most appliances. Get away from the motherboards. Turn the machine on and off when its supposed to, or let it run its Cycles. Dont overfill, because this causes wearing motor parts. The dryer belt wore out on the dryer but that was an easy replacement. Im a woman of 64 and get it myself. Maytag I hope that you get back to the plain ol simple washer and dryer because mine is probably going to wear out which I hope not but I would so love to get the same set I got now.

The HE version of Maytag washer leaves the clothes smelling bad. There are suggestions to remedy this, but why do these type washers cause this? The suggestions dont work. No more HE washers of any brand.

Ten years ago I bought a very expensive set of Maytag Neptune Washer MAH5500BWW and dryer units with the single all-in-one pedestal. The washer starts sounding like a freight train during the fast spin dry cycle. A service tech came out, turned it on, listened, told me it is bad outer tub bearings going bad. And the price to fix is $846. Its essentially a throw-it-away deal. The tech says he has done hundreds of these and its a 3-hour major tear down, the bearings are press fitted and you essentially buy a new outer tub instead of replacing the bearings in the old one. Maytag went out of business and was bought by Whirlpool. What a piece of crap and to think how great Maytag once was. Now I have a dryer and a pedestal that probably wont fit any other washer brand.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

Dont buy a washer from Maytag, they put it together wrong and the transmission leaks so it will stop spinning after time and then it fries the motherboard. Too expensive to fix so you have to by a new one.. Their 10 year warranty is a joke and doesnt cover anything hasnt even been 5 years yet. Garbage products.

I would like to say that I purchased the Neptune washer & dryer for my parents back in 1998. Up to now, 23 May 2015, not once has either of the machines required service and have been functioning well for the past 17 years. This is a testament to the quality and workmanship that is Maytag. This week I have purchased the Maytag Maxima front loading washer & dryer for my home because of Maytags reputation.

My Maytag is 2 weeks old, and knew from the start I had a lemon. The compressor sounds like a giant freezer. I had the service man take a look at it, and while he was here the compressor did not come on. He pulled the plug from the fridge and turned it back on and still it did not turn on. I asked him to stay till it turned on and he said he could not stay any longer. I waited for him from 2 PM till 7:30 PM. He was to arrive between 3 and 6. Talk about frustration, and I only wish I had read all the reports before I bought this junker. I was so worried I decided to get the insurance for 4 years. The reason the ice forms is because you have no control over the ice. You cant see them and they get stuck. I had a side by side before this, and I can kick myself for not buying a side by side again. I was told to shut it it down when youve had enough ice cubes, to stop it from getting stuck. This ice maker is so big and so hard to pull out and the switch to turn it off is on the inside. So far my only complaint was the humming, but I can see a tough road ahead.

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

Purchased our dishwasher 11 months ago from Lowes. Dishwasher has a 10 year warranty on racks and 2 other items. We are 2 adults in the household. Dishwasher is maybe used 4 times a week. Very light use! Circulation pump is bad which also took out the dishwasher solenoid. Im not going to fix because it if only lasts a year again that is a very expensive repair. Very disappointed in this made in the USA product. That was the reason I purchased it. Made in the USA. Come on Maytag. You can do better than this!

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

Well, I thought I was buying quality products dishwasher and refrigerator and both are very disappointing. Of course the Maytag dishwasher (MBD7749AWB2) really upsets me since I just bought it in Aug of 2011. Now it will not finish a load of dishes and I did what the lady at Maytag told me. She said it was the control board. But it is not the control board. It is still working the same as it was. Now what should I do? When they said I had a 10year warranty I didnt think a known product like Maytag would let me down. MAYTAG, YOU SHOULD BE ASHAMED TO ADVERTISE YOUR PRODUCTS TO LASTS! THEY SUCK!

We bought a Maytag refrigerator. Big big mistake. It bangs, makes all kinds of noises. The bottom freezer has ice that builds up once in a while, has to be unloaded and thawed out. We have had several service calls and they do not know whats wrong. Trouble started about a month out of warranty. Called Maytag and they would not do anything. WE are very disappointed in Maytag. We spent more money to get a good product and ended up with junk. We are getting rid of it and buying one that is made by a company that knows what they are doing.

TRASH! Bad, Destructive, Dangerous. I am in awe of the worthless, destructiveness of this machine. This washing machine does not add enough water to even cover clothing. It agitates, tangles & tears clothing. You end up with dirty filthy tangled clothing. And this is after waiting for it to make some kind of idiot decision as to whether or not to wash your clothes at all. I frequently go out and it’s made a decision not to start at all. There also is no lint filter, so subsequent loads of laundry are dirtier than the first. You can’t wash clothes without enough water to cover them. I read online that it adds water depending on the weight of the clothing, so wet the clothing first to make it think it’s a heavier load. When you do that it spins the clothes first before it begins to wash them. Your clothes still come out of the machine dirty. If you’re looking for revenge, make someone a gift of this washing machine. Otherwise, put it out with the trash.

Love my Maytag washer! It is great to have a clear lid so I can see the clothes being washed. Not only the features, it really cleans my clothes. I was surprised at the stains that are removed just from washing them!

Not only did I buy a Maytag washer for the brand name and trusted longevity, but because they were always a good product in the past. When my Maytag EZ-Epic washer drum failed after only owning it for two years, there was no effort made by any associate to cover this under any sort of warranty at all. To replace this part, I was quoted so much money that I could go out and buy a brand new one for the cost of the repair for this faulty part. I am extremely dissatisfied with the way I was treated because the so called product was out of warranty and I will never buy a Maytag product again. Shame on Maytag for ever selling off to such a fraudster of a company.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.