I purchased this washer in January 2017 at our local Home Depot here in Mexico. It was a washer/dryer combo. Now, in July, a mere 6 months and only a few wash loads later, it has gone from the worst machine I have ever owned to what I consider to be garbage material. First of all, it boasts about not using much water. This is true... Only 1/4 of your load is in the 3 inches of water at the bottom of the machine and the top 3/4 never even gets wet. I couldnt believe it. Now, I put 2 sheets in this morning and it fills almost to the point of spilling out, though I have to give it credit for shutting off the water before it actually did so. This is a NEW washing machine!!! I, along with a lot of other folks from what I am now discovering, are all in the same boat. I remember Maytag being a mark of excellence way back in the day... This is no longer the case. Stay away from this company... I know I will.

Less than 1 year ago, my washing machine that my husband bought me was a Maytag Mod #MVWC200XW0. It went. The repairman came and had to put in a brand new capacitor and less than 3 months later, there are two things that are wrong with the washer and I cant use it again. I have to go to the laundromat and take clothes elsewhere to get them done. I took out an extended service agreement in January. Maytag deducted $21.18 from my checking account and they never sent me an invoice for the balance of $42.36. I kept calling and trying to get an invoice. Then on June 25th, I received a letter in the mail that they cancelled my service agreement. I guess this was cancelled in May and they sent me a letter a month later. Now, the repairman was there last night and they could not fix it without us paying upfront and the extended service plan said they didnt even know if we would get reimbursed for any of the parts. This is very poor for a washer that is just a little over a year old. As far as I am concerned, this washer is junk and needs to be junked. My husband got a lemon. I am not putting this amount of money in something that every 3 months has something going wrong with it. I would appreciate a phone call back or something that could be done. Thank you.

This washing machine is garbage! We paid almost 1000$ for it and it damaged most of our clothes. We believe this washer was released from Maytag with a functional problem. Because it does not drain the water and soap properly, therefore it leaves white stains on the clothes after it is done. Please see in the picture. After recommendation from Lowes we clean washed with Affresh for many times, it did not fix the issue! We called Maytag customer warranty service. They sent a technician and his solution did not solve our problem. We called them again and they said if they send a technician again they might charge us 130$. We think Maytag warranty is a waste of time and energy. They are useless. We will never ever buy anything from Maytag.

Bought this Maytag microwave mmv 4205ds March 2016. Have had open/close problems five times in 3 years. Unit replaced under warranty once. Now out of warranty. No need to mention inconveniences we’ve been through. Whirlpool-Maytag obviously have done nothing to correct this problem. I will never buy any of their product again. Wanted to give them ‘0’ stars but program won’t allow me.

This Maytag (1979 model) is about as good as other dishwashers (I always rinse before placing in machine). It does have a lot more buttons that are not used than the last one I used (installed in the 1950s). Delayed start, choice of preheating water or not, choice of drying. Not big enough to do everything when have company and too big to use when no visitors present. When I am alone it takes 3 months to get enough to fill the machine and by that time they are getting moldy so most of the time I wash by hand. Black glass front with imposing row of controls across the top. I normally do not generate enough dirty dishes to warrant having a dishwasher. Since my wife died I have used the dishwasher two to three times a year.

This washer is the worst piece of junk I have ever purchased. From day 1 it never cleaned my clothing. It was too much money to call a repairman so I have lived with it since October 13, 2013 and I have finally been able to buy a new washer this week. My husband would come home from work and ask me why I put dirty clothing in his drawers, he said his clothes stunk and were stained. This washer just did not clean the clothing. It didnt use water. I cannot say how many times I would open it after washing a load and the clothes were dry. It saved water alright, it didnt use any and it was installed properly. If you are going to purchase a Maytag Centennial, run. Dont walk. Run, fly, look the other way, just dont buy this HUNK OF JUNK! I cant even sell it, so we will sell it on eBay for parts just to recoup some of our hard earned money! MAYTAG YOU SHOULD BE ASHAMED OF YOURSELF!

Centennial commercial tech. washer - We purchased this piece of junk in Sept 2013, and had to have a repairman twice before it was six weeks in my home. I wrote several letters but the only thing that I received were applications for insurance to cover repairs. I should have received a replacement as it was bad from day one, but Maytag doesnt replace!!! Its been semi-reliable for the past several months, until early this year. It started jerking when it changed cycles, sounding as if the drum was hitting really hard against the sides. It has continued to do that regularly; now it wont function on the cycle its set on. It wont spin, sometimes the lid lock wont work. It starts filling when it should be draining. This evening, it stayed in the rinse cycle for 40 minutes and when I realized it was still rinsing I had to unplug it to get it stopped. It goes on and on, (and so could I out of frustration). The good name of Maytag has turned to trash, and when it leaves my home, no more Maytags!!! PS. The dryer we got with it takes at least 1 1/2 full cycles to dry a load, and since I couldnt get it to spin properly, Ill be lucky to get this last load dry in 2 to 2 1/2 cycles.

I bought a Maytag dishwasher, when I bought my house (7/2010). I live alone and I use my dishwasher only once a week or once every two weeks. After 3 years of working perfect, it stopped working. I had someone come look at it. After troubleshooting with the basic steps, making sure the water was correctly hooked up, a fuse was not the problem. The dishwasher door was shut completely. He took the racks and all movable parts, & thought something, a piece of glass, etc, was stuck in the drain. Nope. After reading these reviews I realize it is got to be the control panel because the start button will not come on and all these people have the similar problem. It just stopped. Period. The panel lights come on, but not the stop button. I am a single person as stated and on disability and on a very tight budget. I bought a Maytag because of the name and reputation. How long would it have lasted under normal use, say a family of 4, using it nightly? Certainly less than a year. I have no idea what to do now. I cannot afford a repairman, & I am certain it is the control panel on the dishwasher. I do of course have all the model numbers, etc & papers, when I bought it. I can provide proper paperwork, when contacted.

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

Bought a dishwasher about 2 years ago, through Home Depot. After it was installed, contacted Maytag to let them know that it didnt seem to be working correctly. They sent out a repairman, who looked at the machine, and then told us that with the new eco friendly settings, it would be best to let the dishes dry overnight. It seems that the company and its employees dont know [or care] about the product. Contacted their service/helpline to let them know that the screws on the insides of the latch [on the cover] are NOT screwing into anything, they come loose. Person couldnt find same in his system, finally sent screw, but they were the wrong size and didnt work. Just opened the dishwasher this AM, after washing the dishes last night. 12 hours later and they still are not dry. This isnt eco, this is something that is wrong that Maytag doesnt want to address. Buy something else!!!

I purchased this product at an authorized Maytag dealer sixteen months ago (Maytag front-Loading washer, model MHWE55OWW1) for approximately $1,500. The main bearing and drum are now shot. Maytag has acknowledged that it is likely defective. Notwithstanding their conclusion, Maytag has chosen not to offer a repair or replacement. The conclusion is simply that Maytag does not make a very good product, and any prospective purchasers can expect that they will not get any customer support for their products.

Sounds wonderful. Thats what I thought when I let my son have my 20-year-old, still running older washer. I wanted a new one. It worked good for 3 years and then one night I went to throw the clothes in the dryer and its full of water. After the last rinse and spin, it filled again and stopped. So I tried it on every cycle and got the same results. I thought, No problem. We have a great, honest repairman. Ill call him the next day and hell fix it. When I called and told him what type of washer it was, he was surprised it was working at all. Seems they had a problem with water leaking into the transmission. Apparently, I was lucky that mine had worked for as long as it did. Like I said, Im lucky to have an honest repairman. He told me he could charge me to put in a new timer and solve that problem, but I shouldnt waste my money since it is just a matter of time before it goes bad. Seems they were all bad and Maytag never made good on them. Told me the smartest thing to do would just to go ahead, bite the bullet and get another. It will be here Tuesday morning. Hopefully, this will be the last one I have to buy (keeping my fingers crossed since I had hoped the Maytag was going to be the last). My old machine is still running great for my son. Over 30 years my repairman has had to fix quite a few things for me - ice makers, dishwashers and even a timer on my old washer. Thank goodness he was honest enough to not fix my washer. I dont know if there are even any Maytag products around now, but if there are, they will never get my business. I spent a fortune on a machine that should have lasted the rest of my life. Ive had childs toys that lasted longer. My advice is do not buy Maytag.

We purchased a Maytag Bravos Quiet 300 about 8 months ago and it will not clean anything. Not one setting will make this machine clean. You have to wash everything 2 to 3 times. There is no savings of any kind with this machine and I dont know anyone who has the time to wash everything multiple times. Its all about the water; its about as much as you can spit. I ran a hose from the faucet and added 8 gallons about 10 minutes into the wash cycle and was able to clean (float) a set of sheets. I find this energy star machine to be worthless and I would have been better buying an old machine at a garage sale than this Bravos machine. Junk. If you cant float your cloths folks, you might as well be rubbing them on a rock.

I have bought a new Home Depot Maytag Impeller HE washer. After 6 repeat washings of 2 items that are lightweight dark brown it was obvious after drying they had soap and lint and lot hairs on it. I reached with no he detergent. The last 4 times the water level filled to 1 depth even for high level water setting to extra rinse or power wash settings. I went to Home Depot and they suggested I call Maytag repair center on Tuesday after the labor day holiday to have them check it out. I will also call the supervisor at Home Depot as I do not feel paying $600 for a faulty machine is acceptable.

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

This microwave doesnt rotate in use, it only goes back and forth...not as good! I believe the rotating type of microwaves heat your food more evenly, but it might just be a personal preference. I would NOT recommend this type of microwave.

I purchased all new appliances and decided to go with Maytag. My Maytag Refrigerator model MFI2569VEM after 12 months, just after the warranty expired, started leaking all over my kitchen floor. I called Maytag and all they told me was there is no recall on this model and there was nothing they could tell me over the phone. I purchased an extended warranty and that is a whole other problem to get someone out. They said to check the freezer problem I need to call when the leak was occurring, so they could see what is happening. So basically, I need to leave water on my kitchen floor so they could see what is happening. Who hires these people?

I have a Bravos washer model # mvwb45owqo and matching dryer. The price for the pair was $1347.00 plus tax. The washer and dryer were bought Jan 14 2010. 10-10-13 the pump went bad and was replaced. I paid $ 221.00 to have it replaced. 10-31-2013 I was washing a load of cloths and it was very noisy. I call the local dealer and they come out and said that it needs a drive shaft tub part #w10193886. I would be about $300.00 to replace the part. Also they charge $75.00 for a service call. I called Maytag and talked to Ashley (**) from customer service and she said they could not give me any help that the washer was too old. I might also add that my last washer was 3 years old and the motor needed to be replaced. It was also a Maytag. I always thought if you paid more money for quality it was worth it. I am sorry I did not buy a cheap machine from Sears or somewhere else. It would of been 1/2 of the cost and I could of replaced it after 3 years or so if necessary and still been money ahead. We also have 4 rental homes that have all Maytag in it. I will be holding my breath that they are not junk also. I will tell everyone I know not to buy Maytag and I will never own anything that has the Maytag name on it again.

The washer and dryer were purchased together as a set 4 years ago in 2010. There have been times where I actually had clothes come from the washer completely and partially dry due to lack of water inside the washer! It fills based on how many clothes are in the washer or capacity that it senses. I have had so many clothes dry washed and torn up due to its use! If you set the washer to the wrinkle control position it does not go through the last rinse and spin cycle, you must reset it to the rinse, drain, spin cycle again in order to finish processing that load.It has already thrown its belt 2 times! Which my husband had to fix since we could not get in touch with anyone at Maytag who knew what we were talking about! If change gets stuck inside the washer bin in the little groove in the tank it is very difficult to get out, Im sure everyone has washed a pair of pants with the change still in the pockets, yes I know this is user error but if you dont know the change is in the little grooves because you cant see them, it stops the washer! So be sure to search this every time you do laundry!The dryer has a mind of its own! Sometimes it will finish drying your clothes, sometimes it wont finish the time set! Theres no reason just doesnt finish! There is so many reasons I will never purchase this brand again. Ive run out of room and patience. My clothes look like Im homeless!

Why is it when you wash dark clothes they come out with white spots which looks like soap. I have put very little soap and it still appears. I usually wash in cold water so I tried warm water - same result. I have had a Maytag for a least 40 years never had this problem - what is it I am doing wrong? I have to wash and rinse at least 2 more times. I would appreciate a answer so I can fix this.

A pure piece of junk this wash machine is. It is more of a merry go round than a wash machine. I do not understand how it can be called energy efficient. All it does is spin and spin and clothes come out as beautifully dirty as they were loaded. If you make the mistake of putting a few extra clothes (machine calls itself a large capacity), clothes bunch up and one has to pull them apart. The bleach dispenser was used as one would use a bleach dispenser. However it is all rusted. I had bought extended warranty from Lowes but Lowes did not honor the warranty saying rust was a cosmetic issue. Yet when Lowes sold the extended warranty, they did not specify cosmetics were not covered. It is not even cosmetic. It simply is cheap enamel paint.I have used 200 dollar wash machines but never have I experienced such a horrible and annoying product. I will try one more time to see if Maytag will help out with the rust issue. If not, I will simply cut my losses and buy a regular cheap machine. Maytag should be ashamed of itself. I bought a Maytag because I thought they made the best machines!!! Oh! Well, maybe they did at one time.

We bought a Maytag Refrigerator, Model MSB27C2XAMSS from BrandsMart on 2/4/2015. Today, I made my 4th Service Call for the Ice Maker not making ice. The service department has replaced the icemaker, repaired it and still does not work. When I call for service I usually have to wait 5-7 days before I can have a technician come to my home. Also, the refrigerator door does not close unless you push it completely to the refrigerator, unlike most refrigerators that I have had. I would never buy another Maytag refrigerator and certainly will make an informed and researched decision before buying another refrigerator. I am truly dissatisfied with this refrigerator and would suggest looking for other brands.

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

Stove does not heat evenly in oven. Electric burner cannot be turned down to low or simmer, then it will not cook at all. Other burner turned down to low does not stop bubbling and stays at a high temp. There is no consistency. I am extremely disappointed and curse at this stove every day. Model #MER7664XB. Serial #R13316302.

Called about our upteenth issue with our Maytag microwave. Was told the part was covered but we would have to pay for service. The last tech told us how to wiggle the part to make it work. Paid a fortune and it broke again. They do not care about customers!!

We are on our 2nd Maytag washer with the 1st being a top load with agitator and the second without. Both were also bought used. The 1st one broke after I was cleaning it so totally my fault but the second one the door lock broke. Aside from that they do wash clothes well and but I do wish there were more or different cycle settings. Overall they are good machines for out price. (Being used that is.)

We received a MayTag Microwave on Saturday May 10, 2014. There was a minor ding in its case, but it did not show any other damage. After installation I tried to use the microwave. It did not work. So on Monday the 12th I called 800-688-9900 for service. A service appointment was scheduled for Wed May 14th. The service man told us the microwave could not be fixed and had to be replaced. I asked who should replace it. He told me to take it back to the place of purchase.I took it back to the dealer and after a lot of discussion it turned out that MayTag had to replace it. I was given a case number. I called Maytag and was told replacement could take 4 -3 weeks. I could purchase a new microwave and have it by Friday may 16th much sooner than Maytag could do.

Purchased from Lowes October 2014, paid $680.00. Now needs $600.00 in repairs for new springs and basket rim according to a Maytag appliance repairman.Washer is leaking in the front left. Repairman thinks I need 4 new springs and a redesigned taller basket rim to keep the water from pouring out over it. Yes, it is 16 months old!! Ridiculous!

I have always been an advocate for Maytag Appliances. Never bought anything beside Maytag. Our old Maytag refrigerator broke. Would cost too much to fix. So, we decided to buy new. We had the old white, which I was perfectly fine in buying again, however, white was super expensive. So, the salesperson persuaded us to purchase stainless steel. We got a pkg for close to $4000 all in June of 2016. Needless to say, these items have been called for repair within the 1 year warranty over half a dozen times, and have had to replace pieces that have just broken. My worst experience is the stove. I really do not like it at all. I feel the product is misleading. We wanted a self cleaning oven. It is the newest brand out there for what I consider a joke. It is the AquaLift Technology that does not clean anything. My old Maytag self cleaning oven cleaned far better than this. The same spots are in the oven. It just is worthless. I have addressed my frustration with Maytag where I was told that the oven is for the light user. Well, then you need to educate the people who sell your stuff, because I have a family I cook a lot. If this product was made for an apartment single person who does not cook then we should have been informed. Your product states Self Cleaning. Its not self cleaning!!! My frustration went up to the main office of Maytag where their resolution was to give me a discount on a new stove.What do I do with the one I have, and I was told I could sell it!!!! Really Maytag wow from a consumer that has always been a valued customer this is the level of service I get. I ended up purchasing an extended warranty on all Maytag products, because of my fear of something just breaking again. My advice to all is either buy a no named brand or buy something cheaper. Please folks if you have a family do not purchase these products. Its for people that just need a pretty display of appliances!!!

We purchased a Maytag Dishwasher in 2011. In 2014 I got no response from the control panel when trying to start the machine. Service came out and had to replace the control panel. The cost for that repair was $269.00. It has now just stopped working again. Same issue. After seeing all the posts, I realize that this is a prevalent issue and in some cases a safety concern. If Maytag knows about this issue with their control panels why have they not recalled or corrected these problems! Needless to say, I will never trust this company again!!! Model number MDB7749AWM2.

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

I wished I researched more before I purchased, but like most people, I believed in the reputation of Maytag. Like many others - my control panel started to go out 19 months after install: Had my first event with the washer; it would not allow me to select normal wash. A high-end machine shouldnt have electrical connection problems within 19 months, just 7 months after the warranty expires.When the repairman pulled apart our machine, he found a similarly burned looking touchpad ribbon cable, that was burned in exactly the same position as the photos shown on Maytags website under the review referred to. Maytag/Whirlpool has set up a special phone number to deal with this problem: I dialed 1-866-931-7384... Been on hold for over an hour Of course - NO answer! Ill try later but I am very angry that this has been a known issue BEFORE I purchased mine at Home Depot. What a piece of junk. This is the last Maytag Ill ever buy again. The service is horrible, the product is junk.

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

I purchased this Atlantis dryer several years ago. To this day, I have replaced the rollers and drum three times. What a piece of junk! This will be the last Maytag I ever own.

I purchased a Maytag MDBH979SAB0 dishwasher from Home Depot two weeks ago for around $600. I got it installed and it would not turn on. I contacted Maytag and after a few questions, she stated that they would have to send a repairman. After a few days, the repairman arrived and said hed never seen this model before but that we needed a new control panel. After waiting a week with no work, I called Maytag to get an update. The control panel is out of stock and could be a while - they are trying to find one somewhere around the country. They refused to send a replacement dishwasher, even though this was brand new. Their policy says repair, not replace. Dont take the chance purchasing a Maytag dishwasher.

I bought the Bravo XL HP Washer and Dryer in 2014. Dryer is great but the washer just after having it 1 yr started making awful noises. Had a repair man come which cost me money and was told the bearing went out and I needed a new one. He said it would cost over 700.00. I didnt fix it as I could buy a new one for that price. I did that. I hate the washer. It doesnt get the clothes clean and the cycles are long. My clothes dont feel or look as good. I have to leave the top open or it smells awful. So, I got the new washer 1 yr after the other one in 2015. It is now 2016 and it is making noises. Theses washers need to be recalled and we should be able to get a different one or our money back. Please, do something about these washers as a lot of us are stuck with them.

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

We bought a new Maytag top load washer March 2018. July of 2021 it starts making the worst racket Ive ever heard. I thought at first that there was a dog being killed by another animal. As I ran to the door I realized it was my washer. Long story short, repair guy said itd be cheaper to just buy a new washer. Maytag did nothing to help us resolve the issue of a 3 yr old machine totally useless. We bought this machine because we thought it would last for years. I mean their commercial shows the repair guys doing nothing because Maytags never need service. My new machine is not a Maytag. No more Maytags for me.

Purchased a Maytag microwave/range hood in 2005. So yes, it is almost 10 years old but should the handle break off in ones hand? I would say poor material is the culprit. No use contacting the company by the looks of it... they dont stand by their product. Warranty says 10 years but broken handle would likely be cosmetic...

I moved into this house and the dishwasher came with it. For an appliance that is over 8 years old it works beautifully. It cleans my dishes well and doesnt leave residue on them. I ran it through a cleaning cycle recently and that has only improved its performance. I recommend dishwashers by Maytag because they last and perform well.

Purchased the Maytag MMV405DS Microwave and matching refrigerator from Best Buy in 2016, they were exactly what we had been looking for. Little did we know of the problems we would have with the microwave. At the one year mark the infamous open/close door problem begin. Luckily we were still within the warranty period since it was repaired at no charge. However six month later the problem re-occurred, we are now out of warranty and have little recourse. Maytag should have by now have come up with a fix. I find it hard to believe they are still manufacturing this microwave and selling this product knowing it will fail. We have little choice but to replace it with another brand which will not match. Suggest anyone looking for appliances stay away from Maytag.

Had side-by-side refrigerator for over 12 months - Went completely dead - Would need $500 work!!!!! Just got less 6 months. Now need filter for water and air filter!!!!!! I wish I can give it less than one star!!!!

We purchased a new Maytag Bravo washer and dryer on March 4, 2011. On January 26, 2015, our washer stopped spinning the clothes. We purchased these appliances while preparing for retirement, thinking we would possibly never have to purchase them again. There is only two of us! Wrote to Maytag (when it was still Maytag) and got a response of So sorry **, we can fix your washer for $319.00. We could buy a new washer for not much more than that!!!!!

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

Thank all of you for saving me. I was about to buy a Maytag with bottom freezer from Home Depot. No wonder they are marked down an additional 20% off their sale price.

Well, my washer is 2 years old, yes thats right - 2 years old. And it only goes to the wash cycle, washes once and stops, wont complete a full cycle. Yes, the brand with the commercial with the repairman just sitting around because their products are so great you never have to work on them. Yeah right. And Ive seen videos on YouTube on the problem with the Maytags. So Maytag may want to look into it!

Purchased a Maytag Bravos washer model MTW6700TQ ON 5/5/2008. Also purchased extended service agreement. This washing machine was only five years old when it started rusting on the top of the body where you load the clothes and fill the detergent. Not in a million years did I expect a washing machine to be rust-prone. Its a washing machine. The service contract doesnt cover dust, mold, rodent damage, and RUST (like rust is an external source). When I called Maytag they were not surprised. They said the life expectancy of their product could be as little as a year and a half. Regardless of the extended maintenance expense I now must throw this piece of junk away. NEVER BUY A MAYTAG. This time I am buying an LG.

I bought my Maytag Quiet Series 300 about 6 or 7 years ago. About January this year the clean light quit working but the dishwasher was still doing its job. Every once in a while the clean light would come on again and then go away. I did not worry about this as the dishwasher was still working despite the absent clean light. I did call Maytag and told them about this. I believe I even asked if they (customer service rep.) had heard about this and was told no. Last Friday the start button no longer works which means the dishwasher will not function. Some of the other lights/buttons work but not start or clean. I have dealt with Maytag repair service/customer service before about my Maytag washer. I know they are not much help and I always end up paying a lot of money. I am not interested in calling a Maytag repair person in and paying from what 300.00 to 400.00 dollars to get it fixed. Past experience of others seem to prove that it will break down again. Last Maytag appliance that I will ever buy. I used to be a loyal customer. I want to join the class action suit. Please tell me how I can join.

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

I purchased the subject Maytag washer (MHWE201YW-3.5 CU FT WHT FRNT LD WSHR) from Home Depot in December of 2012. I got exactly 1 year of use and then the washer stopped working. I called the Home Depot repair person who came and repaired the unit. The repair lasted two weeks and the washer stopped working again. Because the unit was no longer under its 1-yr warranty the Home Depot repair person was not available for repair. Another independent Maytag repair person came and evaluated to problem. He said the computer which is located on the motor was no good and to the tune of over $400.00 (parts and labor) a new motor was purchased and installed. It lasted two months and it quit working again. After several months I was finally able to contact the original Home Depot repair person for one visit. He said he would check the code message and get back to me. I never heard from him again. I have been taking my laundry to the laundromat ever since and it is getting expensive. I dont want to spend another $400 on this machine as it will only break again. What do you recommend?

Maytag MCT Washer & Dryer - I bought the largest capacity to save time. However even my 6ft tall husband has problems reaching the bottom to remove clothes. Even worse is the lack of water to clean clothes, washes so long it wears clothes and they are still dirty. I tried to improve on my old Neptune and Id love to have it back. I may have to junk this washer. The dryer is very slow. Buying this set was tossing my hard earned money in the trash.

Our Maytag dryer is only, maybe, 3 years old. I do not dry towels, jeans or heavy sweatshirts in it (I line dry and then soften up in dryer). I clean the lint filter each time. Our heating element has gone for the second time. The first time it cost $200-250 to repair. It is so sad that our appliances are not made to last as they did. Or is it just Maytag? You can be sure we will not buy another Maytag item. I am looking into recalls at this time.

I purchased my home in 2008 at which time I bought all brand new Maytag appliances, well the above the stove microwave Ive had to replace the door handle because it broke off and the oven I can only use the very top or bottom to cook on and I cant move them, otherwise the racks will fall through. I have burned myself numerous times as I cant pull the racks in or out and I found that out cooking dinner and when I pulled it out the rack fell through and my dinner went crashing down and splashed everywhere. Due to this fact I hardly ever use it. I contacted Maytag with no help, told me to buy new racks and those did the same thing so it was a $100. It seems as though the liner cant handle the self clean heat and if you look at my oven, the left side is pushed in. If anyone gets help with this issue please let me know. My model number is MERH865RAS serial # 14348133LX. Oh and my refrigerator is a side by side and I have had to have it repaired twice because my food kept thawing out. That model number is MSD2651KES serial 60869476LV all of these are Maytag products and were purchased brand new from Home Depot.

Bought a Maytag Stainless Steel kitchen stove to upgrade my appliance before retirement. 14 months later the spring loaded hinge failed. A bad piece of engineering in the way of a retainer pin to hold the spring pressure tore out of its pressed metal hole. The hollow pin was fastened in place by a 3 fluted punch instead of with a proper rivet with a head. My local parts supplier had 10 on hand so you know they are aware of this. $70 and an hours labor and it is repaired. My local seller said, Too bad you didnt get the extended warranty. So much for Maytag dependability.

Maytag Bravo Washer and Dryer - We are usually review writers. I just felt it was our duty to help others save their hard-earned dollars and not purchase this product. We have owned this expensive and highly researched set for a bit over 2 years. We have had to have repairmen out a half dozen times for dryer repairs. The washer was purchased with the largest tub because I wanted to be able to wash a full load of sheets or a blanket. NOT!!! It gets off balanced, twists every single item (as in blue jeans, towels, soft t-shirts, etc...any weight or size) into a huge mess and has actually ruined some of my clothing. The dryer gives me error messages all the time. I am beyond words with my disappointment. We saved a long time for this set and now are absolutely stuck for a long time before we can replace. You know Maytag my message to you is that hard-working people used to trust your company name. I have been married 43 years and we keep our purchases for many years. I have never in all these years been so disappointed in the huge purchase we made thinking it was a lifetime investment. Now I am doing everything I can to save this year so maybe can replace it down the road as soon as we can. I am telling you people reading this... DO NOT BUY THIS SET. IT IS A TOTAL WASTE OF YOUR HARD EARNED MONEY.

Such a horrible and expensive kitchen purchase. The stainless looking pieces are either fake or very poor quality - they scratch so easily. After the first year of use the top of the stove looked like it was 30 years old. The oven glass is extremely hard to get at to clean - you have to remove very finicky screws that dont go back into place easily. Oven temp is questionable and it takes a very long time to heat up. I would never recommend the Maytag Gemini oven to anyone.

This dishwasher has an electronic control panel that is faulty. Within one year of purchase, the control panel shorted out. It was replaced under warranty. Almost exactly a year after that, the same part failed for the same reason. This time, Maytag refused to replace it for free since it was out of warranty. A new control panel would have cost over $250. Disappointed with this Maytag product and their refusal to replace an obviously defective part, I decided to buy a new dishwasher from another manufacturer. Also, it did not make sense to me to spend that kind of money to replace a part that would continue breaking every year. AVOID Maytag dishwashers with electronic control panels!

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

Within 1 month Maytag sent 2 repairmen to repair my microwave. I paid $271.20 for the repair and part. The same 2 parts used the first 2 times were ordered again and I was told that Maytag could not get them again. The service and parts are supposed to be guaranteed for 3 months. Maytag refuses to refund me; offering me 15% off a new purchase. I would not buy from Maytag. They lost a customer.

Our oven is 3 years old and the last time I used the self clean option caused the control panel to malfunction. Now we have to buy a new panel. The repair guy online advises people not to use the self clean as this is a common problem!!! What? I cant use that feature? That is so ridiculous!!! Now we have to pay $300. Whatever happened to the Maytag claim to quality and you would never see a Maytag repair man? Something needs to be done about the problem of appliances and electronics being so poorly made and basically disposable.

Bought this washer and dryer 3 1/2 years ago mainly because of Maytag name and reputation. They were very expensive to purchase. The washer is a piece of junk 3 1/2 years old used for my wife and I and leaks oil all over the floor. Called repair man to come and look at it, wasnt here 5 minutes said transmission is shot. Cost over $400 to have it repaired. We are junking it and that will be the last Maytag product I ever own.

We purchased a Maytag electric convection oven with a warming drawer 3 months ago. We have been happy with the cooking features, but not the Aqualift self-cleaning. It does not work and Maytag does not acknowledge this. Instead they have offered cleaning products to us which their own instructions tell you not to use! Does this sound like a self-cleaning oven? They have offered to send out a service person to check the temperature. However, from reading multiple reviews by others, there will likely be no satisfaction from this company.

After only 4 years, this washer stopped spinning. Called Maytag support (Ha! the ads show the Maytag repairman sitting by a non-ringing phone) I had to wait 20 mins to get through. Only after paying for a service call would they be able to determine if this problem was motor-related. In reading reviews (which in hindsight I wish I would have done prior to purchasing) this is a common problem and is related to bearings going bad. Pay for service call vs buying a non-Maytag product -- will set this out by the curb and buy a different brand.

My name is Luis ** and I own a Laundromat in Yuma, AZ. I recently purchased 10 Maytag top loaders model MVW18PDAWW in August, so the machines are practically new. They are the new HE top loaders with locking lids. Since I purchased them I have had nothing but trouble. Customers have complained about them on a regular basis; there are days when we have had as many as five complaints.First of all, the locking lids proved to be a much bigger problem than we anticipated. People want to open top loaders to add fabric softeners and when we have opened them so that they can add the fabric softener they are often disappointed with the level of water in the washer. Those people consequently refused to use those particular washers. People have pressed the buttons on the control boards and sent the machines into a loop; different readings have appeared on the screen. Some of them say out of order, sync and several other error codes. Eventually the machines reset themselves or I have had to reset the programming. In the meantime the people pass the word and those machines are not used by those who hear. The controls are too sensitive and are not suited to a commercial coin laundry.Whenever any buttons on the control board are pressed the time of the wash appears on the board. Because of this some people who are busy and are using and loading several washers claim that they have already put their money into the machines; they argue with the attendant or with us. Many times they actually believe that they have placed money in the machine and many times they try to get a free wash from us. Either way they are unhappy and they, and those who hear them argue, will not use those washers again. In most cases we lose them as customers and once customers are lost they never return.I placed them in a location where the previous Maytags had been heavily used, expecting them to replace the old machine. I was wrong. They are used very little and the long and short of it is that we are losing money and since our busy season is coming up, will be losing even more customers and therefore more money. I spent close to $12,000 on the machines, including delivery and installation and right now they are quickly becoming heavy paper weights. I have contacted the salesman who sold them to us, but he has given us the runaround and done nothing about the situation.

Purchased my microwave in 2005 and seldom used it. However in the last few months, the halogen light which lights up the range surface has been flickering. When I asked an electrician doing other work around my house to repair it, he discovered that the halogen light is attached with a dual pin socket which is plastic. When the halogen light gets overheated (and halogen produces alight of heat) it melts the plastic. It has already melted some of the plastic socket. When it fails to operate, I will have to repair the light socket which will be very expensive or buy a new microwave. This microwave cost $800 or more because it offered convection cooking which I have seldom used.This is what is presumed quality appliance? Plus I added the cost of an extended warranty.

Purchased a new Maytag refrigerator in January 2013. In September 2013, the ice maker stopped working and Maytag sent out a repairman to replace the ice maker. In February 2014, the ice maker stopped working again. I contacted Maytag and was told the refrigerator was no longer in warranty. I told them that since the ice maker was replaced in September the warranty should have covered me for a year from that date. The Maytag representative told me that was not had it worked and asked if I wanted them to repair the item for a fee. I bought a non-Maytag ice maker and replaced it myself. It is now July 2015 and the ice maker is still working fine. I am not a repairman.

I purchased both the washer and dryer in this series. First the washer does a horrible job actually cleaning the clothes unless you set it as a bulky load and use more water. Despite that issue, after only owning the set for four years the dryer broke down. It made a terrible noise and you could not run it because it was far too noisy. My husband thankfully bought a replacement part and fixed that issue. A few months later I started having trouble with the washing machine. It freezes constantly and I have to unplug to get it working again. It usually take over 15 times to actually get it to begin to fill with water. Now it started to stop working during the wash cycle and I have to unplug it again to get it going. Most times I have to change it to another setting like rinse and spin or drain and spin to complete a wash cycle. Last night it began to have a plastic burning smell. I used to own the same washer for 20 years and only had minor issues that come with extended use. To only own this pair for under five years and have them both break down proves that these are poorly made products and you should save your money and purchase a different brand altogether. I will never buy another Maytag as long as I live if this is how well their products are made. I expect to have my appliances last longer than five years for their price. So save your money when it comes to these machines. I promise you will not be happy with your purchase. I will either have to repair the washer and hope it will last at least a few more years or chalk this up to a lesson learned and discard both machines.

We bought a new Whirlpool dishwasher, and it was a nightmare. So after four years of that we tried their sister company Maytags dishwasher. I have to say that I think these two old American brands have been ruined. This Maytag dishwasher is always making my dishes smell like rotten fish or a dead animal. I have to dump bleach and or vinegar down in the bottom constantly to keep the stink down. And I have looked and there is no food laying in the grinder. Then we started to lose wash cycles, and the buttons (not real buttons but a cheapo control panel) started to malfunction after 2 years. Now, 3 years into it the plastic adjusters in the top rack are broken, control panel has gone totally haywire, and still smells terrible. I remember when American appliances were sturdy and reliable because they were designed by engineers. Now they must be designed by accountants and shareholders. Goodbye Maytag and Whirlpool.

Buyer Beware! This is by far the WORST washing machine (Maytag Bravo) I have ever owned! The complaints are almost too numerous to list. Among them: Noise level is atrocious, water level is always low and cannot be adjusted, suds do not wash off, clothes do not come clean and get beaten up, takes an hour plus to do a load of laundry, frequently comes unbalanced, do not feel I can leave the house with this running, service calls have provided no fix, Maytag does not care. Do not buy! Saving my pennies to buy a different brand, will never touch a Maytag product again, Surprised there is not a Class Action lawsuit pending. When there is, Ill be right on board.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

Save money. I have always had Maytag & loved them until I bought the Bravos xl top load washer. The salesperson insisted it was a large capacity energy efficient w/ great maintenance record -- greatly misleading. The water level does not rise enough to effectively clean or rinse so clothes do not get cleaned or detergent doesnt rinse out thus allowing only 2 to 3 towels or jeans to wash per load. Such ineffective cleaning cycles create the ongoing need for loads to be rewashed and be extremely small, yielding credence to other consumers’ accusations of being mislead and false advertising of xl capacity. As such, it takes hours to wash a family of threes clothes. The machine shakes like crazy and clothes get ruined as they get twisted and tangled into each other ripping, tearing, misshaping and ruining them.

I bought this wash (XL HD) 1 1/2 years ago. From the time the people installed it it never worked correctly. I have never wanted to beat up an appliance before, but this washer makes me so mad that I am ready to just throw it out and buy a new one even though I paid 600.00 for it and it was more than I would ever pay for a washer. I bought this so I could wash my comforters mainly. Well I cannot wash comforters unless I wash them 5 times or at least try to wash them 5 times or more. They get unbalanced and then the machine shuts off. After doing everything from changing the hoses like somebody else suggested, it still didnt work. Along my troubles with trying to rinse and drain I did find something new that I didnt know I could do for all these months is when you put your machine on rinse, spin, dry and the extra rinse light pops on, click it and turn it off, then it reduces the spin time to 15 minutes instead of 26. Also now I have to just let my hose drain on the floor of my outside wash room because if I hook it up through the wall to drain outside it just stops with the LF code. So I have 2 inches of water on my washroom floor and it really sucks. This is the only way I can get the machine to work without turning itself off. Very disappointed with this machine that appears to be so large (looks can be deceiving). It cannot wash hardly anything and this machine should be taken off the market. It is garbage. I really wish this did work because I have spent too much time trying to rewash, respin, get all the water out of the clothes so I could dry them. This should be banned and not sold by any store.

Owned my Maytag Maxima front loading HE washer for just under 2 years. Went to turn it on one day and got an error code that I later found out meant the computer board went bad (a very costly expense). I called Maytag and explained that a $1200 washing machine should last more than 23 months and if they stand behind their products they should do something to cover this repair. Even after speaking to a manager they told me too bad they couldnt help me. But they would be happy to sell me a $350 extended warranty.... Never again Maytag/Whirlpool!

Electronic control board fried after 3 yrs on Maytag Gemini range - certain buttons on control board would not set for ovens. Called Maytag, said was not covered, past 1 year warranty. Recommended repair shops, all overpriced. The piece cost between $300-500 for a 3 year old stove. Cheapest repairman wanted 90 to install piece. Ordered piece online and replaced it myself with help from YouTube video. Maytag has lousy repair records lately. Of 4 Maytag appliances purchased in 3 yr kitchen remodeling… already had issues with 3 of them. Do not recommend Maytag anymore!

I was pleasantly surprised that this basic model would work so great! It really gets the dishes clean. It came with the house so I did not choose it and probably would not have bought it if I had to shop for it.

I bought this electric dryer Bravos (Model# MEDB850YW0) in Nov. 2011. Since I bought it, its giving me the same problem - it doesnt want to turn on. Today is the 6th time that I have been calling the customer service to fix it. Yesterday, it just got fixed; and today, its not working again for the same problem. I asked them if they can give me a new one, since its not even over 1 year. But they said they will not replace it because it cant be fixed. But it is so ridiculous, and its wasting my time. This is so unfair. I paid $800.00 for this machine.

I purchased this washer from Lowe’s on 8/9/2017. After 3 years and 2 months, this washer would no longer power up. I tried resetting it by unplugging it and lifting lid 6 times. It didn’t work. The extended warranty from Lowe’s expired on 8/9/20. I called a technician and he found it need a control panel and control board. He suggested that I call Maytag to see if they would give me the parts as a courtesy since the washer was only three years old. I contacted them and experienced long wait times (51 minutes was the longest). I spent a total of 3 hours on the phone with them. They said no there was nothing they could do for me since the manufacturers warranty ended 2 years ago and the “mother control panel” doesn’t fall under 10-year motor warranty. Well, there’s no need for a motor warranty if there’s no power to the unit! The cost of the parts would be almost $600. It is shameful to not stand behind your product. I would expect to have to replace an iron or a juicer after 3 years, but not a washer. This was a major blow to how I would view the way they do business. I purchased the extended warranty from Lowe’s. I will never do that again. It was a waste of money. They didn’t make any concessions for me either. They kept saying it was a manufacturers issue.

I bought a Maytag Gemini double oven gas range 5 burners (model MGT8885XS000), even air true convection cooking. Within 4 months, 1 of the gas valves (knobs to turn gas on with) froze. I could not turn one of the top burners off. Maytag came out and fixed it. Three months later, another one froze. Again Maytag came out and fixed it. Our warranty ended. Over the next year, all five burner valves have frozen. I called Maytag, told them what happened. The most they could do for me was to give me the part half off. So I can pay $200.00 for parts and pay for a repairman to come out and fix it. The oven cost $2,000.00. I am still paying for it. Chances are if I repaired it would break again.

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

DISHWASHER MDB7749AWM - We purchased this dishwasher from Home Depot on 10/15/2011 for $630.00 for my birthday and yesterday the start button stopped working (cycle lights still work). We went online to look for more troubleshooting options and we found lots of complaints about faulty control panels. Sounds like thats what we have. VERY disappointed in Maytag for not correcting known issue. My dishwasher is only 3.5 years old and there are only 2 adults in our home. We run the dishwasher 1 to 2 times per week meaning this Maytag dishwasher will only last for about 200 wash cycles. Shame on you Maytag!

We bought a washer & dryer from Home Depot 2 1/2 years ago. The control board went out on my washer. I called Maytag and they wanted $109 for a diagnostic fee and wouldnt tell me how much the labor would be. A control board costs $350. So by the time all is said and done... the money would be better spent buying a new one. Maytags slogan of dependability lasts is a bunch of hooey. Washers should last more than 2 1/2 years and Maytag should back up their appliances. They just lost a customer.

An average refrigerator/freezer at best. I would not recommend it unless you also buy a service agreement to fix things that go wrong with it. Ice maker went out.

We bought a Maytag refrigerator. Big big mistake. It bangs, makes all kinds of noises. The bottom freezer has ice that builds up once in a while, has to be unloaded and thawed out. We have had several service calls and they do not know whats wrong. Trouble started about a month out of warranty. Called Maytag and they would not do anything. WE are very disappointed in Maytag. We spent more money to get a good product and ended up with junk. We are getting rid of it and buying one that is made by a company that knows what they are doing.

Purchased 6-1/2 years ago when we had kitchen remodeled. Bought the stainless steel with stainless interior. The interior design was perfect for placing the various dishes, glassware and utensils. There are a number of settings to choose from, however, we tend to use it as more of a sanitizer so the light or normal wash are the preferred and dont use the heat-dry as we dont find it necessary. Very pleased with the quietness of the cycles and have no regrets with our purchase.

Problems with Maytag dishwasher, purchased at Sears Canada Model MDB7749S is only a couple of years old, and as such is no longer under warranty. This Dishwasher is less than 3 years old! Both the interior and exterior is stainless steel and looks virtually new. Cost of parts and labour to repair amount to more than a new dishwasher--this is unacceptable. Poor design. Little value compared to cost. First issue: bottom rack wheels fall off because the plastic pin holding the plastic wheels on the rack become fall out, leaving no way to hold the wheels onto the rack. Second issue: faulty design of the integrated door handle and control panel on the exterior door face. The control panel pops out of the front cover panel when door is pulled open. With some struggle it can be popped back in.I agree with another reviewer who wrote: The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

I have written to Whirlpool about complaints with this range and was very dissatisfied with response. The following were complaints on above range: Range does not have a light on it as the past ranges had. It is very much needed. Grates on burner are to high, therefore it takes longer for items in pot to heat up. Type of steel used on range is very thin and tiny, in other words very poor quality. This is what has happened since Whirlpool bought out Maytag. Quality of Steel that Maytag used is no longer since Whirlpool took over their products. This is true of All their Appliances (Refrigerators, Washers, Dryers, and Ranges). All meaning appliances manufactured by Whirlpool.Manual knobs for turning on oven have been replaced by touch screens, these eventually wear out and are very costly to replace. If it works why change it. Drawers on bottom of range used to be larger, now they are narrow and smaller height wise. Residue on base of burner appears quite frequently and has to be cleaned even if no overspills occur. And why cant Whirlpool make quality merchandise as good as Maytag use to make. Regarding the physical appearance of Range it is very attractive in looks, however Looking good and functioning poorly with inadequate materials used in construction of Appliances outweighs benefits of looking good. My wife and I regret not returning this appliance within 90 days of purchase. In the future we will not purchase Whirlpool or any other appliances manufactured by them if that is possible. Kenmore, LG and perhaps other appliances parts are made by Whirlpool. I received a response from Jake **, Whirlpool Corporation, Executive Office. The Comment from Jake that did not impress me was this: While we regret you are dissatisfied with the current design of your Maytag Range, this is the model that you selected. His comment says too bad better luck next time. Letter was dated March 5, 2014 received on March 13th or 14th.I sent a handwritten letter to Mr. Jeff Fettig on March 12th which was written on March 11, 2014. No response to handwritten letter to Mr. Jeff M. Fettig. Verification that the Executive Office that my email to you Mr. Jeff Fettig Chairman and Chief Executive Officer Whirlpool Corporation was received on February 20, 2014 by Delores **, Corporate Office Staff. Supposedly Mr. Jeff Fettig.

Bought a 2400.00 refrigerator 1 year and 4 months ago. The freezer quit working and we lost everything in the freezer. We called and were out of warranty. The commercial on tv shows the bored repairman who never has any work because Maytag is so reliable. What a crock! We are going to have to pay for the labor which could be as high as 800.00. This is so wrong. This is a high end refrigerator and the fact that it only lasted a little over 1 year is unbelievable. I would dump it if I could afford to. It is a piece of junk. I will never ever buy Maytag again. Make a new commercial, one where the repairman is so busy he works 24/7. We got screwed by Maytag. They do not stand behind their product, they rob you blind.

We purchased a refrigerator in December 2010 with a 12-month warranty. Since the refrigerator was delivered, we have experienced nothing but problems. Most recently, there was a problem with the auto defrost causing us to lose all our food stored. It also caused water damage to our floor. We scheduled maintenance with a contracted company through MayTag. After three scheduled visits, which made me miss 3 and a half days of work resulting in an additional loss of over $300, our refrigerator is still broken and they just want us to schedule another maintenance visit. When calling Maytag customer service we are literally told, “your loss, there is nothing we can do to resolve your issue, we can only continue to send out maintenance.” I am so disappointed in this company, the product, the customer service, maintenance service etc.

Was coerced into purchasing this fridge three years ago. Told how Maytag is the highest quality fridge etc. From day one it was noisy and seemed to be running half the time. I had asked for a quieter fridge, partially why I paid $2000 for it. Now there is something wrong with it. Not sure what yet. But for $2000 it should not be failing three years later. My Samsung was quieter, 1/3 of the price and lasted at least 8 years. Thought about calling customer service but read too many bad experiences here in regard to that. Will never use Maytag again.

I cook a lot so we wanted to purchase a double oven. We purchased this double oven about 10 months ago. Every day I complain about this range. It cooks very uneven. Called Maytag and they sent out a repairman who said I needed to preheat the oven for 25 minutes before putting my food inside. Dont pay any attention to the beep, because when it says it has preheated but it really hasnt. To think you pay that kind of money for such a piece of JUNK!! Also, I have owned 2 other glass top stoves (the last one I owned for 23 years) and never had a scratch on the surface. Theres already a big scratch on this new one. Glass top on this one is such poor quality. Would not recommend to my worst enemy.

I purchased a new Maytag from Home Depot. It was delivered and installed by them on 7/20/12. Today is 9/18/12. It is less than 2 months old and the tub is starting to shred around the upper rim. I called to get it repaired. What a nightmare. First I tried to understand a Filipino woman through a bad connection. She advised me to call a different customer service number, 1-800-688-9900. I talked to Crystal. She called up information on me using my phone number. She asked for the serial number as she had the model number available from the online registration I completed on 7/20/12. I told her I do not have that and asked where it was located. I also told her that I was unable to get it at this time as I am handicapped. She advised me that I had to show my repairman the receipt or I would have to pay a $60 service charge. I get nervous about throwing good money after bad. So I then asked why. If the serial number is so important, why is it not a required info when you register online? She had no answer. I asked to speak to her supervisor. I waited 4 minutes. Enna finally came on the line. She gave conflicting info about my online registration. She said I was not registered online (if not, how did Crystal have all my other info including my model number? Why did Crystal tell me I had registered without the serial number?). Enna told me that the repairman could key in the serial number when he gets to my house and if my washer was under warranty, I would not be charged. Again I asked why, if the serial number is so critical to the process and with all the info they seem to have on me (name, address, phone number, model number, place of purchase, date of delivery, etc.), why is the location of this very critical number is not in the owners manual? Why do they allow you to register without it online and why dont they track sales and delivery by serial number? She was unable to address these issues. I asked to speak to her supervisor. She told me she would give me her supervisors name and number (Kim, **) but she would not give me a last name or contact information. She told me that she was the highest level that I was allowed to speak with.Bottom line, my Maytag is falling apart, getting through the red tape to get it fixed under warranty is silly. Maytag ignores its own concept of tracking by serial number and does not support the use of serial number by telling you where it is located on an appliance or requiring it to register online. Calling customer service is a joke! I was mad when my new $800 washer started to fall apart. Now I am just sad with the way we allow manufacturers to treat us. Mad about the way we allow them to operate in the United States. They create junk or junk parts overseas, products fall apart over here, calls for repair get routed around the world, and then they create more red tape and call it customer service. I made one bad choice. Hopefully, you are reading this and can avoid your own.

Less than four years ago we purchased a new set of Maytag appliances, refrigerator, stove, dishwasher, microwave, and upright freezer. To date, the only appliance we have not had a problem with is the microwave. The bottom element is not working on our stove model # MER8775AS. We will never buy Maytag or Whirlpool products again. Save yourself time and money!

I bought a front loading Maytag Cloths washer model# MHW3505FW1, SER# C71451407 new in April 2017, from Home Depot, since then it has broken down three times, with a water pump, a master board, and now another master board, we were told by the appliance repair service that is used by Home Depot extended warranty service, that it will take a month to receive the master board. Thats it... Never again will we buy another Maytag or Whirlpool product. This is unacceptable. Gone are the years when Whirlpool and Maytag made quality products!